Wistron NeWeb WLANWARPLINKP Direct Sequence Spread Spectrum Transmitter User Manual User Manual 2411

Download:
Mirror Download [FCC.gov]
Document ID	137188
Application ID	npGBKeYO1PgDDY291VwkXQ==
Document Description	Updated Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	215.73kB (2696592 bits)
Date Submitted	2001-02-20 00:00:00
Date Available	2001-03-23 00:00:00
Creation Date	2001-02-09 16:38:23
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	2001-02-20 09:39:33
Document Title	穨User_Manual_2411
Document Creator	穨 User_Manual_2411.doc - Microsoft Word

IEEE 802.11b WLAN PC Card
WarpLink 2411
User’s Guide
Version:1.08
Please install the Utility/Driver first
before inserting the PCMCIA Card.
FCC Class B Radio Frequency
Interference Statement
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the separation between the equipment and receiver.
3.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4.
Consult the dealer or an experienced radio/television technician for help.
Notice 1:
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Notice 2:
Shielded interface cables, if any, must be used in order to comply with the emission limits.
Notice 3:
This device complies with part 15 of the FCC Rules. The operation is subject to the following two
conditions:
(1)
This device may not cause harmful interference.
(2)
This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: To comply with FCC RF exposure compliance requirements, a separation
distance of at least 2.5cm must be maintained between the antenna of this device and all
persons."
Table of Contents
Introduction ...............................................................................................................................1
Installation .................................................................................................................................2
2.1 Overview .................................................................................................................................. 2
2.2 Install the IEEE802.11b WLAN Utility/Driver.............................................................................. 2
2.3 Install the PCMCIA card.......................................................................................................... 12
2.4 Utility Startup Configuration...................................................................................................... 13
2.4.1 Setting .............................................................................................................................. 13
2.4.2 Wireless LAN Neighborhood ............................................................................................. 15
2.5 Uninstall the IEEE802.11b WLAN Utility / Driver...................................................................... 17
Application...............................................................................................................................21
3.1
3.2
3.3
3.4
File Sharing in Microsoft Windows 98........................................................................................ 21
Printer Sharing in Windows 98 .................................................................................................. 24
Using the shared folder............................................................................................................. 25
Using the shared network printer............................................................................................... 25
Troubleshooting.......................................................................................................................26
4.1 Check the Various Properties of the Card.................................................................................. 26
4.2 Microsoft Networking Checklist................................................................................................ 26
4.3 Others..................................................................................................................................... 29
1 Introduction
Thank you for purchasing our IEEE802.11b WLAN PCMCIA Card. It will be
interoperable among IEEE 802.11b standard compliant products from other
manufacturers and allows you to build a wireless LAN. Besides, you can use your
PC to connect with an access point wirelessly to share the wired network resource:
a. Share your Internet access by using just one connection
b. Share printers and other peripheral devices
c. Share data and image files between networked PCs
d. Play multi-player games
IEEE802.11b WLAN can wirelessly transmit and receive data, minimizing the
need for wired connections, at a speed of up to eleven megabit per second. With
IEEE802.11b WLAN you can locate your PC wherever you want without wires and
cables.
IEEE802.11b WLAN provide LAN users with great mobility, which are not available
under wired network, for real-time information access at anywhere within a
reasonable distance.
The IEEE802.11b WLAN configuration is easy to change from peer-to-peer
networks, suitable for a small number of users, to full infrastructure networks of
thousands of users that allow roaming around a broad area.
Please read this manual to get familiar with the IEEE802.11b WLAN. This manual
contains detailed instructions in operation of this product. Please keep this manual
for future reference.
Kit Contents
The IEEE802.11b WLAN PC Card kit includes the following items:
a. A PCMCIA Card
b. A CD including:IEEE802.11b WLAN Utility & Driver software, Acrobat
Reader3.0 and user manual PDF file.
c. The User’s Guide (this document)
2 Installation
2.1 Overview
In this chapter we will cover how to install the IEEE802.11b WLAN PCMCIA Card.
To establish your wireless network connection, the following steps should be
executed.
1. Install the software using the installation CD
2. Install the wireless LAN card.
3. Install the required network protocols to communicate with your network. Most
likely, you will need the TCP/IP protocol.
The product is designed to operate in Windows 98SE, Windows Me, Windows
NT4.0 with Service Pack 3 or later and Windows 2000. And the installation
procedure is about the same. Please follow up the installation wizard that provided
by your system to install the software. The example here is based on Window
98SE.
2.2 Install the IEEE802.11b WLAN Utility/Driver
Please install the IEEE802.11b WLAN Utility/Driver first
before inserting the IEEE802.11b WLAN PCMCIA Card.
1. Insert the IEEE802.11b WLAN installation CD into your CD-ROM drive. The
setup program will then automatically start.
2. The setup program will start and the setup screen will appear on your monitor.
Select “ Next “ to go to the next screen.
3. Please carefully read the “ Software License Agreement. “ If you accept the
contract, click “ Yes “ to move to the next screen. If not, click “ No “ to
exit.
4. Please select the applications you would like to install, and click “ Next “ . If
you select “ Browse User Manual “ system will prompt a message to suggest
you installing Acrobat Reader.
5. Please choose your wireless device adapter, and click “ Next “ .
6. The default destination folder is displayed in the setup dialog box. To change
the default folder you can click “ Browse “ to set the destination folder. Click
“ Next “ to go to the next screen.
7. Select the Program Folder for IEEE802.11b WLAN Utility and click “ Next “ .
8. You will be asked if you want to add an IEEE802.11b WLAN Utility shortcut to
your desktop. Click “ Yes “ .
9. The user manual is published in Portable Document Format (PDF); we suggest
you install Acrobat Reader to read it. If Acrobat Reader doesn’t exist in your
system, a “ Question “ dialog box will prompt as follows. Select “ Yes “ to
install Acrobat for browsing user manual.
10. If you are sure to install Acrobat, click “ Yes “ and then system will guide
you to enter the Acrobat Reader 3.0 setup program. Follow the setup
procedure to complete the Acrobat Reader 3.0 installation.
11. The following page will remind you to install Microsoft network protocols for
IEEE802.11b WLAN to work properly. If the network protocol has existed in
your system, click “ No “ to the next page, otherwise click “ Yes “ to go to the
network setting and add the necessary protocols. Please refer to the session
4.2 Microsoft Networking Checklist for the detailed Microsoft network setting. If
you add the necessary protocols and finish the network setting, system will
prompt a reboot request and then click “ No “ to go to the next page.
12. The Driver and Help files will be copied to the system. Wait for the setup
program to finish the IEEE802.11b WLAN installation. Then select “ Yes “ and
click “ Finish “ to complete the installation. It’s recommended to close other
applications before rebooting your system.
13. To install the PCMCIA card, please refer to the chapter 2.3. “ Install the
PCMCIA card. “
Additional Note for Windows NT4.0
The installation procedure under Windows NT4.0 will be a little different from Windows
98 shown below. It will be change after step10 refer to the installation of Windows 98.
1. Click “ OK “ and system will auto-select I/O address and IRQ and remind
you to choose the unused I/O address and IRQ from Windows NT Diagnosis
to prevent system resource conflict.
2.
If the Ndis 3.0 packet driver has already existed in your system, the setup
message will be prompted as follows, just click “ OK “ .
3.
A prompt of networking setting will appear as follows. It’s the same as
Windows 98 operating system.
4.
The Network properties page will appear automatically in the screen if you
click “ Yes “ in the last step. You should choose “ AWLAN 11 Mb
IEEE802.11b Adapter “ in the Network Adapter of upper menu and add
necessary protocols, then click OK.
5.
The Microsoft TCP/IP setting page will be prompted. You can use DHCP or
manual set the IP address. The related Microsoft Networking setting is like
Windows 98.
6.
Click “ Yes “ and insert IEEE802.11b WLAN PC card before system reboot.
Additional Note for Windows 2000 to install Packet Protocol
You should add Packet Protocol under Windows 2000If the Packet Protocol
doesn’t exist in your system. The installation procedure will be a little different from
Windows 98. A message will be prompted to guide you to auto-install Packet
Protocol. Follow the on–screen instructions as listed below to complete the
IEEE802.11b WLAN Utility and driver installation.
1. Please insert 802.11b adapter (refer to section 2.3) .If the adapter
installation completed, click on “ Yes “ .
2. If your wireless adapter installed successfully, you will enter “ Packet
Protocol Auto Installation “ frame, click on “ OK “ and system will
auto-install Packet Protocol.
10
3. If Packet Protocol installed successfully, you have to reboot your system and
the IEEE802.11b Utility/driver installation under Windows 2000 is complete.
4. If the Packet Protocol installation has failed, a message will be prompted as
follows. Click “ OK “ to continue next step.
5. System will give you an on-screen instruction as follows to install the Packet
Protocol. Remember and follow the procedure to complete the Packet
Protocol installation and then click “ OK “ .
11
2.3 Install the PCMCIA card
The IEEE802.11b WLAN driver and utilities are
included on the accompanying installation CD.
Please follow the installation procedures in Section
2.2. (Your PCMCIA card will not work properly if the
driver and utilities are not installed correctly.)
Make sure that there is an empty PCMCIA slot for
IEEE802.11b WLAN PC card. Install the
IEEE802.11b WLAN Utility/Driver first before
inserting the PCMCIA card.
1.
Insert the PCMCIA Card and then the system will automatically start.
If you’re asked to insert a “ Windows 98 CD-ROM
“ during the installation, insert your “ Windows 98
CD-ROM “ and click “ Yes “ . Once the setup task
is completed, the “ Microsoft Internet Explorer
“ should start up. Please close it.
2.
When the PCMCIA card setup task is completed, you can start up the IEEE
802.11b WLAN Utility. To start up the utility, please refer to the chapter 2.4
“ Utility Start up Configuration “ .
12
2.4 Utility Startup Configuration
IEEE802.11b WLAN PCMCIA Adapter/Card has its own management software.
Users can control all functions provided by the application named IEEE802.11b
WLAN Utility. The Utility icon will appear in the working bar by clicking the
IEEE802.11b WLAN Utility shortcut on your desktop. The definition of the color of
the Utility icon is as follows:
Connected (Green)
low quality (Yellow)
disconnected (Red)
Double click the icon and the IEEE802.11b Utility will be opened.
2.4.1 Setting
This page is aimed at the basic setting of IEEE802.11b WLAN. You can set the
configuration by changing the following items and click “ Apply “ .
•
Computer Name: The login name of your computer.
•
Mode: If you want to connect with an access point, choose “ Infrastructure “ .
If
you have more stations and just want to set them as
peer- to- peer local network, choose “ Ad Hoc “ .
•
SSID :It is the group name that will be shared by every member of your
wireless network .You will only be able to connect with an Access Point
(AP), which has the same SSID. Note that the SSID will be the
continuous string excluding blank and case sensitivity.
•
Channel: It shows radio channel numbers used for networking. The Channel
can be changed only under the Ad Hoc Mode. If the Mode is
Infrastructure, this parameter will not be active. Infrastructure Client
nodes will always go to the same channel as their AP.
• Click “ Advanced Setting “ and then the following advanced setting about
your
IEEE802.11b WLAN will be displayed.
13
Configuration
•
It displays the configuration items that you can change under the AdHoc mode:
Power Saving Mode, Ethernet Conversion and Data Transmission Rate. If the
mode is Infrastructure, The Tx Rate will be fixed in “ Fully Auto “ and users
can’t change it.
Wired Equivalent Privacy
•
If you would like to enable WEP, the system will prompt a message to suggest
that you contact with your network administrator.
•
You may desire an additional measure of security in your wireless network,
which can be achieved by using the Wired Equivalent Privacy (WEP). Follow
the steps below to set your WEP:
(1) Select the data privacy algorithm you want (64 or 128 bit WEP type)
(2) Type Pass phrase
(3) Click “ Generate “ to generate automatically the corresponding WEP key.
If select 64 bit WEP type, 4 sets of WEP key will be generated; if select
128 bit WEP type, only a set WEP key will be generated.
(4) Choose one key (under 64 bit WEP type)
(5) Click “ Write “ and then press “ OK “ . WEP encrypts each frame
transmitted from the radio, using one of the keys entered from this panel.
(6) If you select “ Manual “ , you can type the 64bit WEP key manually.
Especially note that all the blanks of WEP key have to be filled by manual
typing. Click on “ Clear “ you can clean away all the settings of
Encryption.
14
Country
•
Every country has different legal frequency range. Please choose proper
country setting. Under the infrastructure mode, the setting value will be
determined by the Access Point and can’t be set by users.
2.4.2 Wireless LAN Neighborhood
•
The Access Point SSID and Access Point MAC will appear in the screen if
you choose the Infrastructure Mode. Your Station Name and MAC Address
will appear if you choose the Ad Hoc Mode. (Please refer to the 2.4.1 Setting
to set your network mode.) The status of the Link Quality and Signal Strength
will be showed under the Wireless LAN Neighborhood.
•
Double click the Access Point SSID (under the Infrastructure Mode) or
Network Neighbors in the frame of Utility (under the Ad Hoc Mode) to access
to the Microsoft Network Neighborhood folder to find other on-line computers.
•
Click “ Rescan “ if you don’t find any other station.
•
Clicking “ More “ will spread the following information about your network:
15
Link Information
•
The link information, including the Current Channel, Transmission Rate,
Transmission State, is revealed here.
About
•
From this dialog box, you can get the details such as the MAC address and the
version information of each S/W.
16
2.5 Uninstall the IEEE802.11b WLAN Utility / Driver
1.
First you should remove the IEEE802.11b WLAN PC card. To safely remove
your PC card, we suggest you should follow the procedure below.
Click the Start Menu, choose Settings – Control Panel, and click the PC Card
(PCMCIA) icon. You will enter the PC Card (PCMCIA) Properties page as
follows, choose “ IEEE802.11b Wireless LAN Adapter “ and then click the
“ Stop “ button to disable PCMCIA socket. As the message: “ You may safely
remove the device “ prompted you may remove your PC card.
Additional Note for Windows Me
If you use Windows Me operating system, you may double click the “ Unplug
or Eject Hardware “ icon at the lower right side of the screen to enter the
picture as follows. You may choose the IEEE802.11b Wireless LAN Adapter
from Hardware devices list and then click “ Stop “ button to remove this
device. The procedure is like on Windows98 operating system.
17
2.
To exit the IEEE802.11b WLAN Utility, you should click the right bottom on the
Utility icon in the working bar and select “ Exit “ .
3.
To uninstall the IEEE802.11b WLAN Utility and Driver, you can move to Start –
Programs – IEEE802.11b WLAN Utility, and click
“ IEEE802.11b
Un-Installation “ .
4.
You will be asked if you want to uninstall the IEEE802.11b WLAN Utility and all
of its components. Click “ Yes “ to start to uninstall or click “ No “ to exit.
5.
Now the un-installation is completed. Please click “ Finish “ .
18
Additional Note for Windows NT4.0
The additional pages will be prompted as follows under the un-installation
procedure on Windows NT 4.0 operating system.
1. A un-installation guide will be prompted as follows, just click “ OK “ and follow
the steps on it.
2. The network properties page will be prompted automatically as follows, select
“ AWLAN 11Mb IEEE 802.11b Adapter “ and then click on “ Remove “ button.
If the step is finished press “ OK “ .
3. The warning message will appear as follows if you want to remove the
component from the system, and then click on “ Yes “ .
19
4. Make sure the AWLAN 11Mb IEEE 802.11b Adapter has been removed and
click on “ Close “ , and then system will restart.
Additional Note for Windows 2000
The following items should be noted:
1. Please don’t remove your PC card unless the IEEE802.11b WLAN
un-installation is completed.
2. Make sure to exit the IEEE802.11b WLAN Utility before uninstalling.
3. If you are sure to uninstall the IEEE802.11b WLAN Utility and Driver, the
system will give you a prompt as below to execute “ Device Manager “ to
remove the IEEE802.11b WLAN adapter, and then click “ OK “ .
4. System will give you a prompt as below while waiting for “ Device Manager “ .
Follow the instruction to uninstall IEEE802.11b WLAN adapter.
20
3 Application
To enable the sharing of the Internet access, you should set your IEEE802.11b
WLAN mode as “ Infrastructure “ and connect to the access point (please refer
to the chapter 2.4.1 “ Setting “ ). When the procedure is completed, an access
point will appear on the Wireless LAN Neighborhood of IEEE802.11b WLAN
Utility. Double click it to enter the Network Neighborhood folder. This folder
contains the links to all computers in your workgroup on the entire network.
3.1 File Sharing in Microsoft Windows 98
IEEE802.11b WLAN allows the sharing of files between computers that are logged
onto the same wireless network. Let’s assume that you want your folder “ My
Documents “ to be shared with other computers and the wireless network:
1. First, locate the folder “ My Documents “ and right click it.
2. Select “ Sharing “ from the available options.
3. Select “ Shared As “ to open your folder for file sharing. You can also select
and define the level of access you want for your folder.
21
•
If “ Read-Only “ is selected, the other users in the wireless network can only
copy files from your folder. Copying files into your folder is not allowed.
•
If “ Full “ is selected, the other users in the wireless network have full access
into your folder. They can copy to and from your folder as well as modify files.
•
You can also set the option to “ Depends on Password “ wherein the user in
the wireless network can access to your folder through a set password. The
set password will determine if the user can only read your folder or has full
access to your folder.
4. Click “ Apply “ or “ OK “ to activate the options that you have set.
Now you can see the folder “ My Documents “ with a little hand under it. The
folder is now open for file sharing.
22
Sharing files in the IEEE802.11b WLAN wireless network will be like sharing files
on a wired LAN.
23
3.2 Printer Sharing in Windows 98
In order for a printer to be shared across the network, it has to be set as the
network printer. Follow the instructions below to set a printer as a network printer:
1. Click the “ Start “ button, point to the “ Settings “ , and then click “ Printers “ .
2. In the Printers window, click the printer you want to share.
3. Click “ Sharing… “ on the “ File “ menu.
4. Click the Sharing tab, then click “ Shared As “ , and if necessary, enter a
password.
24
3.3 Using the shared folder
1.
Double click the “ Network Neighborhood “ icon, and then double click the
computer where the shared folder is located.
2.
Double click the folder you want to connect to.
3.
You may want to assign a drive letter for shared folder that you connect to.
4.
In the “ Network Neighborhood “ , double click the computer where the
shared folder is located.
5.
Click the folder you want to connect, and click “ File “ menu, and then click
“ Map Network Drive “ .
6.
Select an available drive, and then click OK.
Note: If a password is required, the Windows will prompt you. Then you need to
enter the password that had been assigned to this shared folder.
3.4 Using the shared network printer
1.
In the “ Network Neighborhood “ , locate and double click the computer where
the printer you want to use is located.
2.
Double click the printer icon in the window.
3.
To set up the printer, follow the instructions on the screen.
Note:
1. After you have set up a network printer, you can use it as if it were attached to
your computer.
2. If a password is required, the Windows will prompt you, and you need to enter
the password that had been assigned to this shared printer.
Whenever printing a document through the network,
be sure to select the printer that is set as the
network printer.
25
4 Troubleshooting
If you encounter some problems installing the IEEE802.11b WLAN PC card or you
want to confirm whether your card is installed properly or not, refer to below the
procedure after you have installed the card.
4.1 Check the Various Properties of the Card
•
Click the “ Control Panel “ and then the “ PC Card “ . Check whether there is
a PCMCIA card in one of the sockets or not.
•
If you find an IEEE802.11b WLAN Adapter (PCMCIA) in one of the sockets, it
means a card is detected.
•
If you see a Question-mark (?) or Exclamation-mark (!) in yellow, the
resources are conflicting.
•
Right click “ My Computer “ and then select “ Properties “ . Select the Device
Manager and click the Network Adapter. You will find the IEEE802.11b WLAN
PC Card if it is installed successfully.
•
If you see the yellow sign, the resources are conflicting. Click “ PCMCIA Card
“ and then “ PCMCIA Card Service “ , you can see the status of the PCMCIA
Card.
•
If there are yellow signs either on the adapter or the PCMCIA card, please
check the followings:
1) Check if your Notebook supports 3.3V Card.
2) Check if your Notebook has a free IRQ. If not, make an IRQ free by
assigning the same IRQ to some devices.
3) Check that you have inserted the right card and have installed the proper
driver.
4.2 Microsoft Networking Checklist
In order for the IEEE802.11b WLAN to run properly, some network items must be
presented in the Microsoft “ Network Neighborhood “ setup. To check and activate
the network setup, right click the “ Network Neighborhood “ with your mouse. The
following items should be presented in the network setup:
1. IEEE802.11b Wireless LAN Adapter (PCMCIA)
2. IPX/SPX-compatible
(PCMCIA)
Protocol ->IEEE802.11b Wireless LAN Adapter
3. NetBEUI -> IEEE802.11b Wireless LAN Adapter (PCMCIA)
4. TCP/IP -> IEEE802.11b Wireless LAN Adapter (PCMCIA)
5. File and printer sharing for Microsoft Networks.
6. Client for Microsoft Networks
26
27
If any of these items are missing, please follow the instructions below to install them
properly:
Set up the Network Protocols:
•
Click “ Add “ and select “ Protocol “ on Network “ Configuration “ .
•
Click “ Add “ and then choose the network protocol. Select Microsoft as the
manufacturer and “ NetBEUI “ , “ TCP/IP “ , and “ IPX/SPX-compatible “ for
the network protocols. Then click “ OK; “
•
Now your network protocol should be set. Please check if your network needs
any special requirements to operate in your office environment.
Network Service for Microsoft Networking:
•
Click “ Add “ and select “ Service “ .
28
•
Select “ Microsoft “ as the manufacturer and choose “ File and printer
sharing for Microsoft Networks “ for network service;
•
Click “ OK “ to set the network service.
4.3 Others
Wired Equivalent Privacy (WEP)
If you set the WEP Pass phrase, which is the same as the Access Point (AP) in
your IEEE802.11b WLAN PC card, but still can’t connect with the AP. It may be
that the key generated by your PC card is different from the key generated by the
AP even if the same Pass phrase is used between your PC card and AP. Please
follow the steps below to set WEP manually.
1. Check the WEP type and WEP key generated from the AP.
2. Select “ Manual “ on Wired Equivalent Privacy in your IEEE 802.11b Utility
advanced setting.
3. Type a set of WEP key generated from the AP into the key1blank of your
Encryption frame, other space you can type anything you like, but make
sure all the blanks will be filled.
4. Remember to press the “ Write “ button and “ OK “ to finish the WEP
setting.
Additional Note for Windows 98 earlier edition
If your system is running Windows 98 first edition, you may use one of the
following ways to make IEEE 802.11b WLAN Utility work properly.
1. Copy and replace the file MFC42.dll from c:\windows\system of Windows
98SE to the same directory of your Windows 98 first edition.
2. Upgrade your system and IE from Microsoft web site.
29
Additional Note for Windows NT4.0
1. If you are not the first time to install WLAN IEEE 802.11b Utility and driver
under Windows NT4.0, the following message will be prompted during
installation:
“ NDIS3.0 Packet Driver has existed in the system. “ Click “ Yes “ to
update the new driver.
2. If your WLAN Utility and driver can’t work properly, make sure the setting of
I/O address and IRQ are correct. From Start/System Manager Tool/Windows
NT Diagnosis/Resource to find the unused I/O address and IRQ, and then
choose one of them from the combo box.
Additional Note for Windows 2000
1. IEEE802.11b WLAN Utility error message
•
If the IEEE802.11b WLAN Utility and Driver installation has completed under
Windows 2000, but an error message appeared as follows, you should check if
your adapter inserted successfully and packet protocol installed successfully.
(See Section 2.2 “ Install the IEEE802.11b WLAN Utility/Driver “ -----Additional
note for windows 2000 to install packet protocol, in the User Guide for details.)
2. Uninstall failed
•
If you cannot uninstall IEEE802.11b WLAN Utility and Driver successfully.
Please follow the procedure below to reinstall the Utility and Driver.
(1) Find the file AWLAN.isu and delete it from the Programs files\
IEEE802.11bWLAN Utility folder.
(2) Reboot your system
(3) Reinstall IEEE802.11b WLAN Utility and Driver.
30

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : .穨.     User_Manual_2411.doc - Microsoft Word
Create Date                     : 2001:02:09 16:38:23
Title                           : .穨.User_Manual_2411
Producer                        : Acrobat PDFWriter 4.0 for Windows
Modify Date                     : 2001:02:20 09:39:33-06:00
Page Count                      : 34

EXIF Metadata provided by EXIF.tools