Wistron NeWeb XRAV1 NFC MODULE User Manual WG3004A U5 Product Specification

Download:
Mirror Download [FCC.gov]
Document ID	3150120
Application ID	xjXMf3jDX0gvnCn0fIrVtA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.85kB (323069 bits)
Date Submitted	2016-09-28 00:00:00
Date Available	2017-03-27 00:00:00
Creation Date	2017-12-15 10:39:46
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-15 10:39:46
Document Title	WG3004A-U5 Product Specification
Document Creator	Microsoft® Office Word 2007
Document Author:	Tim Yen

XRAV-1 USER MANUAL
(V0.9)
Model Name:
Description:
Version :
XRAV-1 NFC MODULE
NFC reader/writter module compatible
V 0.9
This document contains proprietary information which is the property of Wistron NeWeb Corporation
and is strictly confidential and shall not be disclosed to others in whole or in part, reproduced, copied, or
used as basic for design, manufacturing or sale of apparatus without the written permission of Wistron
NeWeb Corporation.
NFC module Delivery Specification
V0.9
1. Introduction
XRAV-1 is a kind of NFC (Near Field Communication) module that could be embedded in one IT
system by simply connecting the module through I2C interface and start developing his application
software.
2. Hardware Block Diagram
XRAV-1 is a full feature NFC module and compliant with NFC standards (NFC Forum, EMVCo,
ETSI/SCP). XRAV-1 has an optimized architecture for low-power consumption in different
operation modes. The RF contactless front-end is supporting various transmission modes according
to NFCIP-1, NFCIP-2, ISO/IEC14443, ISO/IEC 15693, ISO-14443, MIFARE, and FeliCa
specifications. The major internal components are illustrated in Figure 1-1.
Host FPC/FFC Connector
Antenna Connector
FPC/FFC CABLE Insert into Connector
Figure 1-1 NFC
module Major Component and System Interface (Assembly Guide)
Note:
• Host FPC/FFC Connector:
Allow user to connect the XRAV-1 module to the host board via FPC/FFC connector.
• Antenna Connector:
Connected to FPC antenna, please note that matching circuitry should be design on antenna.
NFC module Delivery Specification
V0.9
3. Pin Definition
3.1 FPC/FFC connector type
Host connector
Pin number
Name
MOD_VDD
MOD_GND
SWP
MOD_VUP
Configuration
Power Supply Input
Power Supply Ground
Input/ Output
Power Supply Input
IRQ
Output
VDD_SIM
Power supply input
I2C_SDA
I2C_SCL
MOD_GND
Input/ Output
Input
Input
10
Reset/ WakeUp
Input
11
DWL_REQ
Input
12
SWP_PWR
Power Supply Output
13
MOD_VDD
Power supply input
14
15
VDD_IO
MOD_GND
Power supply input
Power Supply Ground
(PMUVCC)
(SIM_VCC)
Description
Module power supply
Module ground
Single Wire Protocol line to UICC/ SIM
Power supply for RF Front-end
Interrupt request from module to
platform
The power rail used to power UICC/
SIM. Applicable in a system where NFC
module used SWP to communicate with
an UICC/SIM in the platform
I2C data
I2C clock
Used for extra GND for signal integrity
Reset pin input from the host to wake up
the device from standby and also to reset
the device
Control pin to set the NPC300 in
firmware download mode
Power supply to UICC/ SIM or power
supply ‘request’ to PMIC. Applicable in
a system where NFC module uses SWP
to communicate with an UICC/ SIM in
the platform.
Additional pin for module power supply
to support higher current capacity
Host IO reference voltage
Module ground
Antenna connector
Pin number
Name
ANT1
RXP
TX1
GND
TX2
RXN
ANT2
NFC module Delivery Specification
Configuration
Output
Input
Output
Ground
Output
Input
Output
Description
Connection for antenna load modulation #1
Antenna reception path #1
Antenna transmission line #1
Antenna ground
Antenna transmission line #2
Antenna reception path #2
Connection for antenna load modulation #2
V0.9
3.2 SMT type
Pin number
Name
MOD_VUP
Configuration
Power Supply Input
IRQ
Output
VDD_SIM
Power supply input
I2C_SDA
I2C_SCL
Input/ Output
Input
Reset/ WakeUp
Input
DWL_REQ
Input
10
VDD_IO
MOD_GND
MOD_GND
Power supply input
Power Supply Ground
Power Supply Ground
11
ANT1
Output
12
13
14
15
16
RXP
TX1
GND
TX2
RXN
Input
Output
Ground
Output
Input
17
ANT2
Output
18
19
MOD_VDD
SWP
Power Supply Input
Input/ Output
(PMUVCC)
NFC module Delivery Specification
Description
Power supply for RF Front-end
Interrupt request from module to
platform
The power rail used to power UICC/
SIM. Applicable in a system where NFC
module used SWP to communicate with
an UICC/SIM in the platform
I2C data
I2C clock
Reset pin input from the host to wake up
the device from standby and also to reset
the device
Control pin to set the NPC300 in
firmware download mode
Host IO reference voltage
Module ground
Module ground
Connection for antenna load modulation
#1
Antenna reception path #1
Antenna transmission line #1
Antenna ground
Antenna transmission line #2
Antenna reception path #2
Connection for antenna load modulation
#2
Module power supply
Single Wire Protocol line to UICC/ SIM
V0.9
4. Specification
Standard specifications
Item
Main chipset
Frequency
NFC
Standards
Host interface
I2C Address
Host
connector
Antenna
connector
Operation
temperature
Storage
temperature














NXP NPC300
13.56MHz
ISO/IEC 14443A, ISO/IEC 14443B PCD
FeliCa PCD mode
Mifare PCD encryption mechanism
ISO/IEC 15693/ICODE VCD mode
NFC Forum tags
NFCIP-1/NFCIP-2 protocol
EMVCo 2.0.1 for PICC and PCD mode
NFC Forum Wave 1 and Wave 2
ETSI/SCP 102 613 and 102 622 for SWP/HCI
NCI protocol interface according to NFC Forum NCI 1.0 standardization
I2C High-speed mode supported
0x29
 15 pin FPC/FFC
 7 pin FPC/FFC
 -25 ~ 80o C
 -25o ~ 125o C
5. Electrical Characteristics
Recommended Operating conditions
Symbol
MOD_VDD
MOD_VUP
Parameter
Power supply input
Power supply input
VDD_IO
IO power supply
VDD_SIM
Power supply input
Power supply for SWP
interface
[1] No VDD_SIM power supply input.
SWP_PWR[1]
Min
2.7
2.7
1.62
3.0
1.62
3.0
Typical
3.3
3.3
1.8
3.3
1.8
3.3
Maximum
5.5
5.5
1.98
3.6
1.98
3.6
1.62
1.8
1.98
Unit
Current consumption characteristics
Symbol
Min
IMOD_VDD
-IVDD_IO
-[1] MOD_VDD=3.3V
NFC module Delivery Specification
Typical
---
Maximum
190[1]
15
Unit
mA
V0.9
6. Recommended Operation Temperature
Supply voltage
Type of DC Source
Operational Climatic
 AC mains
 Internal DC supply
 Tnom (20°C)
NFC module Delivery Specification
DC
 External DC adapter
 Tmax (80°C)
 Battery
 Tmin (-25°C)
V0.9
7. Host Reference Circuit
7.1 No SIM Card used
7.2 SIM Card used on mother board
NFC module Delivery Specification
V0.9
8. Certifications and Regulatory
Item
Feature
14.1
FCC
14.2
IC
Description
RF: FCC part 15C
EMI: FCC part 15B
RSS-210 ISSUE 8
RSS-GEN ISSUE 4
RF: EN 302 291-1 V1.1.1, EN 302 291-2 V1.1.1
EN 300 330-1 V1.8.1, EN 300 330-2 V1.6.1
14.3
CE
EMC: EN 301 489-1 V1.9.2, EN 301 489-3 V1.6.1
Safety: EN 60950-1:2006/A11:2009+A1:2010+A12:2011+A2:2013
RF: LP0002
14.4
NCC
14.5
SAR
EMI: CNS 13438
EN62311
General:
This modular approval is limited to OEM/Integrators installation only.
OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or
install module.
The end user manual shall include all required regulatory information/warning as show in this manual.
End Product Labeling (FCC)
When the module is installed in the host device, the FCC ID label must be visible through a window on
the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a
second label must be placed on the outside of the final device that contains the following text: “Contains
FCC ID: _NKR-XRAV1_________
The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Required FCC Compliance Statement for Host Integration
To integrate this module into the host, the host manufacturer is responsible for the applicable FCC rules,
including the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
In the user manual of the host device, the following statements are required to be included.
 This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NFC module Delivery Specification
V0.9
 This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
–Consult the dealer or an experienced radio/TV technician for help.
 Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Module Integration Restriction:
This device is intended only for OEM integrators under the following conditions:
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
(3) The Loop antenna was verified in the conformity testing. Radiated transmit power must be equal to
or lower than that specified in the FCC/IC Grant of Equipment Authorization for FCC ID: NKR-XRAV1
and IC: 4441A-XRAV1. A separate approval is required for all other antenna type, or higher gain
antenna.
In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and
the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate
FCC/IC authorization.
NFC module Delivery Specification
V0.9
Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm between
the radiator & your body.
R&TTE Regulation:
In all cases assessment of the final product must be met against the Essential requirements of the
R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article
3.3 requirements.
1. The Loop antenna (gain: N/A dBi) was verified in the conformity testing, and for compliance the
antenna shall not be modified. A separate approval is required for all other operating configurations,
including different antenna configurations.
2. If any other simultaneous transmission radio is installed in the host platform together with this module,
or above restrictions cannot be kept, a separate RF exposure assessment and CE equipment certification
is required.
CE RF Exposure Compliance
This device meets the EU requirements and the International Commission on Non-Ionizing Radiation
Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic fields by way
of health protection. To comply with the RF exposure requirements, this equipment must be operated in
a minimum of 20 cm separation distance to the user.
1177
NFC module Delivery Specification
V0.9
End Product Labeling (IC)
Labeling Requirements for the Host Device (Section 3.2, RSP-100, Issue 11, January 2016): The host
device shall be properly labeled to identify the module within the host device. The Industry Canada
certification label of a module shall be clearly visible at all times when installed in the host device,
otherwise the host device must be labeled to display the Industry Canada certification number of the
module, preceded by the words ―Contains transmitter module, or the word ―Contains, or similar
wording expressing the same meaning, as follows: "Contains transmitter module
IC:_4441A-XRAV1___.
Required IC Compliance Statement for Host Integration
To integrate this module into the host, the host manufacturer is responsible for the applicable Industry
Canada rules, including the limits for a Class B digital device, pursuant to ICES-003 of the Industry
Canada Rules
CAN ICES-3(B)/ NMB-3(B)
In the user manual of the host device, the following statements are required to be included.
 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
 Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement."
IC Module Integration Restriction:
This module has been certified by Industry Canada as modular approval with the following restrictions:
1. The Loop antenna was verified in the conformity testing, and for compliance the antenna shall not be
modified. A separate approval is required for all other operating configurations, including different
antenna configurations.
2. If any other simultaneous transmission radio is installed in the host platform together with this
module, or above restrictions cannot be kept, a separate RF exposure assessment and IC equipment
certification is required.
NFC module Delivery Specification
10
V0.9
NCC remind
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司
商號或使用者均
不得擅自變更頻率 加大功率或變更原設計之特性及功能
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干
擾現象時，應立即停用，並改善至無干擾時方得繼續使用
前項合法通信，指依電信法規定作業之無線電通信
低功率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機
設備之干擾
NFC module Delivery Specification
11
V0.9
NCC logo location
NFC module Delivery Specification
12
V0.9

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : Tim Yen
Create Date                     : 2016:09:21 18:58:43+08:00
Modify Date                     : 2016:09:26 18:05:42+08:00
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29
Format                          : application/pdf
Creator                         : Tim Yen
Title                           : WG3004A-U5 Product Specification
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2016:09:26 18:05:42+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:e8b1df61-d2c8-4c04-81a4-fa34f528d2e4
Instance ID                     : uuid:8c03d96d-05eb-421a-9658-42450277786f
Page Count                      : 13

EXIF Metadata provided by EXIF.tools