Woods Equipment Gill Str48S 2 Users Manual MAN0101

STR72S-2 to the manual 25145108-8ff1-43b6-a661-87e5761d38f1

2015-02-05

: Woods-Equipment Woods-Equipment-Gill-Str48S-2-Users-Manual-408662 woods-equipment-gill-str48s-2-users-manual-408662 woods-equipment pdf

Open the PDF directly: View PDF .
Page Count: 28

OPER ATOR'S MANUAL

Super Turf Renovator

& Seedbox

MAN0101

Rev. 3/09/2010

Tested. Proven. Unbeatable.

STR48S-2

STR60S-2

STR72S-2

2 Introduction

Gen’l (Rev. 3/5/2010)

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions

and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual

are completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that

all Dealer Check List items have been completed. Please contact your dealer to complete this form. Dealers can

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and

safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become

acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be

obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in

the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and

satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.

Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary

tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for

safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces

provided:

Model: _______________________________ Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.

The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with

an exclamation mark) to indicate the degree of hazard for items of personal safety.

Introduction 3

MAN0101 (Rev. 9/15/2006

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

PARTS INDEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .25

REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER

Si no lee Ingles, pida ayuda a

alguien que si lo lea para que le

traduzca las medidas de seguridad.

LEA EL INSTRUCTIVO!

4 Introduction

MAN0101 (Rev. 9/15/2006)

SPECIFICATIONS

Super Turf Renovator STR48S STR60S STR72S

Working Width 47" 59" 71"

Overall Width 58" 70" 82"

Roller Pins 1/2" x 1-3/4" 1/2" x 1-3/4" 1/2" x 1-3/4"

Bearing (Self-Aligning) Six 1" Six 1" Six 1"

Front Roller Positions Adjustable for Increased Agitation

Roller Diameter: Front & Rear 8" 8" 8"

Hitch Cat. I Cat. I Cat. I

Tractor HP Requirement 65 HP Max. 65 HP Max. 65 HP Max.

Weight STR48: 565 lbs. STR60: 710 lbs. STR72: 855 lbs.

Weight w/Seedbox STR48S: 820 lbs. STR60S: 920 lbs. STR72S: 1050 lbs.

Seedbox Capacity 3 Bushel 4 Bushel 5 Bushel

Seed Distribution Method Metered gear with flow adjustment lever

GENERAL INFORMATION

The purpose of this manual is to assist you in operating

and maintaining your Super Turf Renovator. Read it

carefully. It furnishes information and instructions that

will help you achieve years of dependable perfor-

mance. These instructions have been compiled from

extensive field experience and engineering data. Some

information may be general in nature due to unknown

and varying operating conditions. However, through

experience and these instructions, you should be able

to develop procedures suitable to your particular situa-

tion.

The illustrations and data used in this manual were cur-

rent at the time of printing but, due to possible inline

production changes, your machine may vary slightly in

detail. We reserve the right to redesign and change the

machines as may be necessary without notification.

■ Super Turf Renovator should never be oper-

ated with any safety shielding removed.

Throughout this manual, references are made to right

and left direction. These are determined by standing

behind the equipment facing the direction of forward

travel.

(Rev 3/09/2010)

Safety 5

STR48-72 Safety Rules (Rev. 7/28/2005)

TRAINING

Safety instructions are important! Read all

attachment and power unit manuals; follow all

safety rules and safety decal information. (Replace-

ment manuals and safety decals are available from

your dealer. To locate your nearest dealer, check

the Dealer Locator at www.WoodsEquipment.com,

or in the United States and Canada call 1-800-319-

6637.) Failure to follow instructions or safety rules

can result in serious injury or death.

If you do not understand any part of this manual

and need assistance, see your dealer.

Know your controls and how to stop engine and

attachment quickly in an emergency.



Operators must be instructed in and be capable

of the safe operation of the equipment, its attach-

ments, and all controls. Do not allow anyone to

operate this equipment without proper instructions.

Never allow children or untrained persons to

operate equipment.

PREPARATION

Check that all hardware is properly installed.

Always tighten to torque chart specifications

unless instructed otherwise in this manual.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

Make sure attachment is properly secured,

adjusted, and in good operating condition.

Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.

Make sure all safety decals are installed.

Replace if damaged. (See Safety Decals section for

location.)

A minimum 20% of tractor and equipment

weight must be on the tractor front wheels when

attachments are in transport position. Without this

weight, tractor could tip over, causing personal

injury or death. The weight may be attained with a

loader, front wheel weights, ballast in tires or front

tractor weights. Weigh the tractor and equipment.

Do not estimate.

OPERATION

Keep bystanders away from equipment.

Do not operate or transport equipment while

under the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from

equipment while engine is running. Stay clear of all

moving parts.

Always comply with all state and local lighting

and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.

Always sit in power unit seat when operating

controls or starting engine. Securely fasten seat

belt, place transmission in neutral, engage brake,

and ensure all other controls are disengaged

before starting power unit engine.

Look down and to the rear and make sure area

is clear before operating in reverse.

Use extreme care when working close to fences,

ditches, other obstructions, or on hillsides.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud-

denly on slopes.

Use extreme care and reduce ground speed on

slopes and rough terrain.

(Safety Rules continued on next page)

Safety is a primary concern in the design and

manufacture of our products. Unfortunately, our

efforts to provide safe equipment can be wiped

out by an operator’s single careless act.

In addition to the design and configuration of

equipment, hazard control and accident preven-

tion are dependent upon the awareness, con-

cern, judgement, and proper training of

personnel involved in the operation, transport,

maintenance, and storage of equipment.

It has been said, “The best safety device is an

informed, careful operator.” We ask you to be

that kind of operator.

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

6 Safety

STR48-72 Safety Rules (Rev. 7/28/2005)

(Safety Rules continued from previous page)

Watch for hidden hazards on the terrain during

operation.

Stop power unit and equipment immediately

upon striking an obstruction. Turn off engine,

remove key, inspect, and repair any damage before

resuming operation.

MAINTENANCE

Before dismounting power unit or performing

any service or maintenance, follow these steps:

disengage power to equipment, lower the 3-point

hitch and all raised components to the ground,

operate valve levers to release any hydraulic pres-

sure, set parking brake, stop engine, remove key,

and unfasten seat belt.

NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment

or between moveable parts even when the engine

has been turned off. Hydraulic system leak-down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment

to drop or rotate unexpectedly and cause severe

injury or death.

• Service work does not require going under-

neath.

• Read Operator's Manual for service instruc-

tions or have service performed by a qualified

dealer.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

Make sure attachment is properly secured,

adjusted, and in good operating condition.

Keep all persons away from operator control

area while performing adjustments, service, or

maintenance.

Tighten all bolts, nuts, and screws to torque

chart specifications. Check that all cotter pins are

installed securely to ensure equipment is in a safe

condition before putting unit into service.

Make sure all safety decals are installed.

Replace if damaged. (See Safety Decals section for

location.)

STORAGE

Block equipment securely for storage.

Keep children and bystanders away from stor-

age area.



SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety 7

MAN0101 (Rev.9/15/2006)

6 - PN 20106 Red Reflector

3 - Serial Number Plate

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can

enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your

nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United

States and Canada call 1-800-319-6637.

MODEL NO. SERIAL NO.

Woods Equipment Company

Oregon, Illinois, U.S.A.

SHIELD MISSING

Do not operate.

Put shield on.

DANGER

18868-B

5 - PN 18868

CONTACT WITH ROTATING PARTS

CAN CAUSE SERIOUS INJURY.

WARNING

15502--B

ROTATING COMPONENTS

Do not operate without cover in place.

Look and listen for rotation. Do not

open cover until all components have

stopped.

4 - PN 15502

9 - PN 24611 Slow Moving Vehicle

(Safety Decals continued on next page)

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

8 Safety

MAN0101 (Rev. 9/15/2006)

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

2 - PN 55122

1 - PN 55121

7 - PN 1003751

WARNING

55121--C

FALLING OFF CAN RESULT IN BEING RUN OVER.

Tractor must be equipped with ROPS (or ROPS CAB) and

seat belt. Keep foldable ROPS systems in “locked up”

position at all times.

Buckle Up! Keep seat belt securely fastened.

Allow no riders.

RAISED IMPLEMENT CAN DROP AND CRUSH.

Never go underneath raised implement which can drop

from equipment or tractor 3-point hitch hydraulic leak

down, hydraulic system failures, movement of control

levers or mechanical linkage failures.

Service work does not require going underneath

implement. Read manual instructions.

FALLING OFF OR GOING UNDERNEATH IMPLEMENT

CAN RESULT IN SERIOUS INJURY OR DEATH.

CRUSHING AND PINCHING HAZARD

 Be extremely careful handling various parts of

the machine. They are heavy and hands, fingers,

feet, and other body parts could be crushed or

pinched between tractor and implement.

 Operate tractor controls from tractor seat only.

 Do not stand between tractor and implement

when tractor is in gear.

 Make sure parking brake is engaged before

going between tractor and implement.

 Stand clear of machine while in operation or

when it is being raised or lowered.

FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN

SERIOUS INJURY OR DEATH.

WARNING

1003751-A

TO AVOID SERIOUS INJURY OR DEATH:

 Read Operator's Manual before operating, servicing or

repairing equipment. Follow all safety rules and

instructions. (Manuals are available from dealer or call

1-800-319-6637.)

 Operate from tractor seat only.

 Lower equipment to ground, stop engine, remove key

and set brake before dismounting tractor.

 Never allow children or untrained persons to operate

equipment.

 Never allow riders.

 Keep bystanders away from equipment during operation.

 Keep all shields in place and in good condition.

 Do not transport towed or semi-mounted units over 20

mph.

FAILURE TO FOLLOW THESE INSTRUCTIONS CAN

RESULT IN INJURY OR DEATH.

55122-D

WARNING

1003750

ENTANGLEMENT AND

FALLING HAZARD

Do not stand on rollers while machine is in

operation or parked.

Failure to follow these instructions

could result in serious injury or

death.

8 - PN 1003750

(Safety Decals continued

from previous page)

Operation 9

MAN0101 (Rev. 9/15/2006)

OPERATION

The operator is responsible for the safe operation of

this renovator. The operator must be properly trained.

Operators should be familiar with the equipment, the

tractor, and all safety practices before starting opera-

tion. Read the safety rules and safety decals on page 5

through page 8.

Recommended tractor ground speed is from 2 to 5

mph.

Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.

Never allow children or untrained persons to

operate equipment.

Keep bystanders away from equipment.

Keep hands, feet, hair, and clothing away from

equipment while engine is running. Stay clear of all

moving parts.

Stop power unit and equipment immediately

upon striking an obstruction. Turn off engine,

remove key, inspect, and repair any damage before

resuming operation.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

Super Turf Renovator Roller Operation

The Super Turf Renovator is an excellent turf recondi-

tioning tool. Its ground penetration promotes a healthy

root system by allowing water, air, and sunlight to enter

the roots.

For best results, adjust the renovator level front to back

so that the front and rear rollers work together. Control

forward and backward pitch by adjusting the tractor's

Top Link Pin

DP2

Operation 11

MAN0101 (Rev. 9/15/2006)

Adjust Front Roller Angle

1. Position tractor and renovator on a level surface.

2. Raise renovator slightly off the ground.

3. Stop engine and set parking brake.

4. Remove klik pin (21), lock pin (15), and lock

assembly (5) from front of renovator. See Figure 6.

Figure 6. Lock Pin and Lock Assembly

5. Raise the adjustment handle (16) and pivot it to the

next adjustment hole. Move handle rearward, front

roller will start to angle. Continue this process until

front roller has the desired angle.

Figure 7. Adjustment Handle

6. Install lock assembly (5), lock pin (15), and klik pin

(21) to secure front roller into position.

7. Reverse this procedure to move front roller back

into normal position.

Seeding Operation

Tractor speed and seed flow settings are critical for

proper seed population. Check the seed control chart,

on the inside of the seedbox lid (see page 11). Adjust

the flow control handle (Figure 8) as needed for the

seed being used and the population desired.

Tractor speed (normally 2-5 mph) should be estab-

lished so that uniform seed incorporation occurs with

the action of the rollers. The seed chart is based on a

standard sprocket configuration. Any adjustments to

this ratio will result in a change to the flow rate, as

described in the chart.

NOTE: The seed control chart should be used as a

general guide only.

Before seeding an area, check the attitude of the

seeder and adjust the top link so that the front and rear

rollers are level. Adjust the 3-point lower lift stop so that

the roller spikes penetrate the ground at 3/4" or enough

to remove the tracks left by the tractor tires.

Figure 8. Flow Control Handle

DP3

DP4

OPEN

CLOSED

DP7

12 Operation

MAN0101 (Rev. 9/15/2006)

Operating Tips

IMPORTANT

■ Before closing down the cup (reducing rates),

the operator should make certain that the cups are

not full of seed. If cups are full of seed (especially

small, round, hard seed), it may be necessary to

cover the meter holes and run seeder a short dis-

tance to reduce level of seeds in meter. Failure to

do so could result in damage to seed cup.

1. Do not allow dirt to build up on the roller sprockets.

Clean sprockets and chain as needed. Excessive

buildup of material can cause damage to the roller

and idler shafts.

2. Always run the drive chain with some slack in the

chain. An extremely tight chain can damage the

roller shaft, the roller bearings, and the idler shaft

and bearing.

3. When properly torqued, the hex lock nut (1) drives

the seedbox roller chain. Disengage the seedbox

chain, when not in use, by backing off a 1/4 turn on

the lock nut.

Figure 9. Drive Chains

Pre-Operation Check List

(OWNER’S RESPONSIBILITY)

___ Review and follow all safety rules and safety

decal instructions on page 5 through page 8.

___ Check that equipment is properly and securely

attached to tractor.

___ Check that all safety decals are installed and in

good condition. Replace if damaged.

___ Do not allow riders.

___ Check that all hardware is properly installed and

secured.

___ Check that shields and guards are properly

installed and in good condition. Replace if dam-

aged.

___ Check all lubrication points and grease as

instructed in Lubrication Information, page 12.

___ Make sure tractor ROPS or ROPS cab and seat

belt are in good condition. Keep seat belt

securely fastened during operation.

DP8



Operation 13

MAN0101 (Rev. 9/15/2006)

Equipment

You will need the following equipment to calibrate your seeder.

1. Two jack stands.

2. One to two pound sample of seed.

3. One tarp or canvas approximately 48" x 84".

4. One scale capable of measuring ounces or tenths of a pound.

Procedure

1. Evenly distribute seed in the bottom of seed box.

2. Raise STR just enough to lift rear roller spikes off the ground and

securely block the rear corners of the frame with jack stands. Blocking

up prevents hydraulic leak down or mechanical component failure.

3. Place a canvas or trap under STR to collect seed.

4. Open seed cups half way and lock into position.

5. Turn rear roller in the direction of travel the number of revolutions as

indicated in the Formula section.

Calibrating the STR for unlisted seed or seed blends

6. Weigh the collected seed and calibrate.

7. If seed rate is not correct, repeat steps 1 through 6, after adjusting

the seed cup opening.

Formula

Revolutions per 1000 sq. ft.

STR48 - 87

STR60 - 69

STR72 - 58

Weight of collected seed

(___oz. x .0625 = ___ lbs.)

Seed per acre

(___ lbs. x 43.56 = ___ lbs. per acre)

Example

STR48 rear roller was rotated 87 complete revolutions in the direction

of travel as specified above. Collected seed weighed 10 ounces or .63

pounds (10 oz. x .0625 = .63 lbs). Seed rate was calibrated at .63 lbs. x

43.56 = 27.4 lbs. of seed per acre.

SEEDING RATE CHART

Alfalfa

(uncoated)

Bermuda

(hulled)

Blue Grass

(Kentucky)

Clover

(sweet, red)

Fescue

(creeping red) Italian Rye Timothy

Setting Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

Lbs per

1000 Sq Ft

Lbs per

Acre

1/4 Open* 1-1/4 52 1-1/4 52 1/2 22 1-1/2 67 1/2 18 1-1/4 50 1 45

1/2 Open 3-1/4 142 3-1/2 149 1-1/4 52 3-1/4 142 1-1/4 50 2 83 2-3/4 119

3/4 Open 5 216 5-1/4 224 2 82 5-1/4 224 1-3/4 74 2-3/4 116 4-1/2 194

Full Open 6-3/4 291 7 298 2-1/2 104 6-1/2 298 2-1/4 99 3-3/4 165 6-1/4 268

Rates are intended as a guide only. Variation in seed size and cleanliness will affect rates.

Check acreage and pounds of seed used and calibrate seeding rate per manual instructions for best results.

*Seed cups will crack some seeds at this setting. Not recommended: Lentils, Sorghum, Sudan Grass1001998

14 Owner Service

MAN0101 (Rev.9/15/2006)

OWNER SERVICE

The information in this section is written for operators

who possess basic mechanical skills. If you need help,

your dealer has trained service technicians available.

For your protection, read and follow the safety informa-

tion in this manual.

NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment

or between moveable parts even when the engine

has been turned off. Hydraulic system leak-down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment

to drop or rotate unexpectedly and cause severe

injury or death.

• Service work does not require going under-

neath.

• Read Operator's Manual for service instruc-

tions or have service performed by a qualified

dealer.

Keep all persons away from operator control

area while performing adjustments, service, or

maintenance.

Before dismounting power unit or performing

any service or maintenance, follow these steps:

disengage power to equipment, lower the 3-point

hitch and all raised components to the ground,

operate valve levers to release any hydraulic pres-

sure, set parking brake, stop engine, remove key,

and unfasten seat belt.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

Lubrication Information

1. Lubricate all six bearings housings every 8 hours.

Bearing housing are located on each end of rollers

as indicated by grease fitting (A). See Figure 10.

2. Lubricate grease fittings (B) & (C) every 8 hours.

3. Clean fittings prior to lubrication. Do not let

excessive grease build up around lubrication

points.

NOTE: One pump of a good grade multi-purpose

grease should be sufficient in most cases. Harsh or dry

conditions may require more frequent lubrication.

Figure 10. Lubrication Points

Cleaning

After Each Use

●Remove large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

●Inspect machine and replace worn or damaged

parts.

●Replace any safety decals that are missing or not

readable.

Periodically or Before Extended Storage

●Clean large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

●Remove the remainder using a low-pressure water

spray.

1. Be careful when spraying near scratched or torn

safety decals or near edges of decals as water

spray can peel decal off surface.

2. Be careful when spraying near chipped or

scratched paint as water spray can lift paint.

3. If a pressure washer is used, follow the advice

of the pressure washer manufacturer.

●Inspect machine and replace worn or damaged

parts.

●Sand down scratches and the edges of areas of

missing paint and coat with Woods spray paint of

matching color (purchase from your Woods

dealer).

●Replace any safety decals that are missing or not

readable (supplied free by your Woods dealer).

See Safety Decals section for location drawing.

CAUTION

Assembly 15

MAN0101 (Rev.10/15/2004)

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

Assembly of this equipment is the responsibility of the

Woods dealer. It should be delivered to the owner com-

pletely assembled, lubricated, and adjusted for normal

operating conditions.

In most cases the Super Turf Renovator is shipped

completely assembled from the factory. The seed box

is an option that can be added to the Super Turf Reno-

vator at a later time if desired.

Install Seedbox

1. Place seedbox on top of renovator mounting

saddles.

2. Install four carriage bolts (18) from underneath

saddles and secure with flanged lock nuts (19).

See Figure 11.

3. Do not tighten until all adjustments are completed.

18. 5/8 NC x 1-1/2 Carriage bolt GR5

19. 5/8 NC Flange lock nut

Figure 11. Seedbox Hardware Installed

Install Drive Sprocket

1. Place washers (12), sprocket (13), and lock nut

(15) on the left side of rear roller drive axle (Figure

12).

2. Do not tighten nut at this time.

NOTE: When properly torqued, the hex lock nut drives

the seedbox roller chain. Disengage the seedbox chain

when not in use by backing off a 1/4 turn on the lock

nut.

12. 3/4 Flat washer

13. Drive sprocket, 18T w/bearing

15. 3/4 NC Nylok Jam nut

Figure 12. Drive Sprocket Installed

Install Idler Bracket

1. Remove hex nuts (31) and hardened flat washers

(30) from cap screws securing the spring bracket to

the renovator. See Figure 13.

2. Place idler bracket assembly over cap screws and

install washers (30) and hex nuts (31) previously

removed. See Figure 14.

30. 5/8 Hardened flat washer

31. 5/8 NC Hex nut

Figure 13. Spring Bracket and Hardware

DP11

DP10

DP12

3130

16 Assembly

MAN0101 (Rev.10/15/2004)

Figure 14. Idler Bracket Assembly Installed

Install Roller Chains

1. Place roller chain (A - 35 link) around the seed box

sprocket and the large inner sprocket on the idler

bracket assembly. Secure chain using master link.

2. Install roller chain (B - 28 link) around the rear drive

sprocket and smaller outer sprocket on the idler

bracket assembly. Secure chain using master link.

3. Align the seed box sprocket and large inner

sprocket on the idler bracket by adjusting seed box

side to side.

4. Tighten hardware securing seed box to renovator

frame.

5. Slide idler bracket assembly forward to apply

tension to the horizontal drive chain.

6. Slide idler and spring bracket down to apply

tension to the vertical drive chain.

NOTE: Do not over tighten. Allow some slack in chain.

7. Adjust opposite side of roller to level.

A. Roller chain 35-LK w/adjustable links

B. Roller chain 28-LK w/adjustable links

Figure 15. Sprockets and Chains Installed

DP14

Idler Bracket

Assembly

3130

DP13

Idler Bracket

Assembly



Parts 17

MAN0101 (Rev. 9/15/2006)

PARTS INDEX

Main Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 19

Seedbox Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21

Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Quick Hitch Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Super Turf Renovator

& Seedbox Kit

STR48S-2

STR60S-2

STR72S-2

18 Parts

MAN0101 (Rev. 9/15/2006)

STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY

Parts 19

MAN0101 (Rev. 9/15/2006)

STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY PARTS LIST

REF STR 48-2 STR 60-2 STR72-2 QTY DESCRIPTION

1 ………… ………… ………… 1 STR Frame

2 1000778 1000778 1000778 1 Rear roller arm, right

3 1000779 1000779 1000779 1 Rear roller arm, left

4 D2213 D2213 D2213 4 Bushing, 0.88 ID

5 1002912 1001716 1001716 1 Lock assembly

6 1001984 1001984 1001984 2 Spring pin, .75 x 11.8

7 20A125 20A125 20A125 2 Compression spring

8 20A920 20A920 20A920 6 Bearing w/housing

9 46483 46483 46483 2 Sleeve, .82 x 1.05 x .66

10 1002018 1002018 1002018 1 Sleeve, .81 x 1.25 x 2.06

11 SU105 SU105 SU105 2 Category 1 drawbar pin w/lynch pin

12 SU106 SU106 SU106 1 Spring bracket, left

13 SU107 SU107 SU107 1 Spring bracket, right

14 ………… ………… ………… 1 Slide plate

15 1002914 1002914 1002914 1 Lock pin

16 SU905 SU905 SU905 1 STR Handle

17 100292548 100292560 100292572 2 Roller retainer assembly

18 100290848 100290860 100290872 1 Rear roller assembly

19 100290948 100290960 100290972 2 Front roller assembly

20 13759* 13759* 13759* 2 3/4 NC x 2-1/4 Cap screw GR5

21 27542* 27542* 27542* 1 7/16 x 11/32 Klik pin HT

22 2864* 2864* 2864* 4 3/4 SAE Flat washer

23 14334* 14334* 14334* 2 3/4 NC x 3 Cap screw GR5

24 FA446 FA446 FA446 5 3/4 NC Nylok nut

25 835* 835* 835* 3 3/8 NC Hex nut

26 31207* 31207* 31207* 1 3/4 NC x 4 Cap screw GR5

27 29485* 29485* 29485* 4 3/4 Hex jam nut

28 3231* 3231* 3231* 1 3/8 NC x 2 Cap screw GR5

29 34473* 34473* 34473* 4 5/8 NC x 3 Cap screw GR5

30 57817 57817 57817 8 5/8 Hardened flat washer

31 230* 230* 230* 4 5/8 NC Hex nut

32 838* 838* 838* 29 3/8 Lock washer

33 976* 976* 976* 26 3/8 NC x 1-1/2 Cap screw GR5

34 300157* 300157* 300157* 2 3/8 NC x 2-1/4 Cap screw GR5

35 1002943 1002943 1002943 2 .82 x 1.06 x .407 Sleeve

36 1002942 1002942 1002942 4 .68 x 1.02 x .66 Sleeve

37 1003828 1003828 1003828 1 Manual tube

38 1002934 1002934 1002934 — Safety decal set

39 1002935 1002935 1002935 — Complete decal set

40 1002938 1002938 1002938 — Replacement pins (25-pin set)

* Obtain Locally

20 Parts

MAN0101 (Rev. 9/15/2006)

STR48-2, STR60S-2 & STR72S-2 SEEDBOX ASSEMBLY

Parts 21

MAN0101 (Rev. 9/15/2006)

STR48-2, STR60S-2 & STR72S-2 SEEDBOX PARTS LIST

REF STR 48-2 STR 60-2 STR72-2 QTY DESCRIPTION

1 1000001 1000001 1000001 1 Seedbox support bracket, left

2 100001348 100001360 100001372 1 Shaft, .38 square w/holes

3 ………… ………… ………… 1 Center stiffener

4 1000766 1000766 1000766 1 Seedbox support bracket, right

5 100293248 100293260 100293272 1 Seedbox assembly complete

(3 & Decals)

6 100293348 100293360 100293372 1 Lid assembly complete

(13, 32, 37, & decal)

7 1000782 1000782 1000782 2 Bearing double row, 17 x 40 x .5 mm

8 1000783 1000783 1000783 1 Bearing block

9 1000784 1000784 1000784 1 Agitator shaft assembly

10 1000787 1000787 1000787 1 Seedcup shaft assembly

11 1000790 (8) 1000790 (10) 1000790 (12) Compression spring

12 1001705 1001705 1001705 1 Control lever

13 1001721 1001721 1001721 1 Seedbox hinge, 36"

14 100172248 100172260 100172272 1 Shaft, .38 square

15 46490 (8) 46490 (10) 46490 (12) Seedcup kit

18 1001986 1001986 1001986 1 Spacer, 1.22

19 1001987 1001987 1001987 2 Spacer, 2.56

20 1001988 (6) 1001988 (8) 1001988 (10) Spacer, 5.88

21 1001993 1001993 1001993 1 Spool assembly

22 1001992 1001992 1001992 1 Control plate

23 20A653 20A653 20A653 1 Spur gear agitator (28T)

24 20A654 20A654 20A654 1 Spur gear feed (30T)

25 20A656 20A656 20A656 1 Sprocket (15T)

26 1001997 1001997 1001997 2 Agitator bracket

27 20A663 20A663 20A663 2 Bushing, .5 x .75 x .75

28 20A664 (16) 20A664 (20) 20A664 (24) Agitator washer

29 20A687 20A687 20A687 1 Collar

30 20A765 20A765 20A765 1 Spacer, .75

31 1001714 (8) 1001714 (10) 1001714 (12) Washer, .44 square hole

32 20A635 20A635 20A635 1 Lid handle

33 1001978* 1001978* 1001978* 18 Blind rivet 3/16, #.63

34 1002016* 1002016* 1002016* 2 Chain, #2 double loop 9 link

35 FA159* FA159* FA159* 4 Eye bolt, 1/4 - 20 x 1

36 70065 (36) 70065 (40) 70065 (44) 1/4 NC Whiz nut

37 1001975 1001975 1001975 2 Flex draw latch

38 1001994* 1001994* 1001994* 6 Blind rivet 1/8, #.43

39 12169* 12169* 12169* 10 3/8 NC x 1-1/4 Cap screw GR5

40 14350* 14350* 14350* 11 3/8 NC Flange lock nut

41 3231* 3231* 3231* 2 3/8 NC x 2 Cap screw GR5

42 70067 (22) 70067 (26) 70067 (30) 1/4-20 x 1/2 Whiz bolt

43 70068 70068 70068 6 1/4-20 x 3/4 Whiz bolt

44 6697* 6697* 6697* 1 3/8 NC x 1 Carriage bolt

45 66840 66840 66840 1 3 Prong knob, 3/8 NC

47 1001995 (16)* 1001995 (20)* 1001995 (24)* 1/8 x 1 Roll pin

48 FA404* FA404* FA404* 2 1/8 x 1-1/2 Roll pin

49 FA405* FA405* FA405* 1 1/8 x 1-3/4 Roll pin

50 1006607 1006607 1006607 1 SMV Bracket

51 24611 24611 24611 1 Sign, (SMV) slow moving vehicle

* Obtain Locally

22 Parts

MAN0101 (Rev. 9/15/2006)

STR48-2, STR60S-2 & STR72S-2 DRIVE ASSEMBLY

REF STR 48-2 STR 60-2 STR72-2 QTY DESCRIPTION

1 ………… ………… ………… 1 Seedbox assembly

2 ………… ………… ………… 1 STR Assembly

3 1001710 1001710 1001710 1 Chain guard bracket

4 7832* 7832* 7832* 2 5/8 NC x 1-1/2 Cap screw GR5

5 57817* 57817* 57817* 2 5/8 Heavy lock washer

6 230 230 230 2 5/8 NC Hex nut

7 1000791 1000791 1000791 1 Idler bracket

8 1001983 1001983 1001983 1 Idler sprocket w/bearing

9 1002930 1002930 1002930 1 Roller chain 35-LK with adjustment links

10 1002931 1002931 1002931 1 Roller chain 28-LK with adjustment links

11 35139* 35139* 35139* 1 Retainer ring, .05 x .75

12 1257* 1257* 1257* 2 3/4 Flat washer

13 SU613 SU613 SU613 1 Drive sprocket w/bearing

14 12296* 12296* 12296* 1 1/4-28 x 15/32 Grease fitting

15 56722 56722 56722 1 3/4 NC Nylok jam nut

16 1001709 1001709 1001709 1 Chain guard

17 66840 66840 66840 3 3 Prong knob, 3/8 NC

18 5607* 5607* 5607* 4 5/8 NC x 1-1/2 Carriage bolt GR5

19 19025* 19025* 19025* 4 5/8 NC Flanged lock nut

20 FA419 FA419 FA419 2 Connector link

21 100293648 100293660 100293672 1 Deflector assembly, (includes item #23)

22 1002939 1002939 1002939 1 End support

23 1001975 1001975 1001975 2 Flex draw latch

24 1001994* 1001994* 1001994* 4 Blind rivet

25 12169* 12169* 12169* 2 3/8 NC X 1-1/4 Hex head cap screw GR5 ZP

26 14350* 14350* 14350* 2 3/8 NC Flange lock nut

27 1002934 1002934 1002934 — Safety decal set

28 1002935 1002935 1002935 — Complete decal set

29 1002959 1002959 1002959 1 #40 SGL Pitch offset link

* Obtain Locally

Parts 23

MAN0101 (Rev. 9/15/2006)

STR48-2, STR60S-2 & STR72S-2 QUICK HITCH KIT

REF PART QTY DESCRIPTION

1 ………… 1 STR Frame

2 1001702 2 Quick hitch sleeve

24 Appendix

Bolt Torque & Size Charts (Rev. 10/10/2005)

BOLT TORQUE CHART

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific

application.

Fasteners must always be replaced with the same grade as specified in the manual parts list.

Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.

Make sure fastener threads are clean and you start thread engagement properly.

All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.

Diameter

(Inches)

Wrench

Size

MARKING ON HEAD

SAE 2 SAE 5 SAE 8

lbs-ft N-m lbs-ft N-m lbs-ft N-m

1/4" 7/16" 6 8 10 13 14 18

5/16"1/2"121719262737

3/8"9/16"233135474967

7/16"5/8"3648557578106

1/2" 3/4" 55 75 85 115 120 163

9/16" 13/16" 78 106 121 164 171 232

5/8" 15/16" 110 149 170 230 240 325

3/4" 1-1/8" 192 261 297 403 420 569

7/8" 1-5/16" 306 416 474 642 669 907

1" 1-1/2" 467 634 722 979 1020 1383

SAE SERIES

TORQUE

CHART

SAE Bolt Head

Identification

SAE Grade 2

(No Dashes)

SAE Grade 5

(3 Radial Dashes)

SAE Grade 8

(6 Radial Dashes)

METRIC SERIES

TORQUE

CHART

Metric Bolt Head

Identification

8.8

Metric

Grade 10.9

10.9

Metric

Grade 8.8

Diameter &

Thread Pitch

(Millimeters)

Wrench

Size

COARSE THREAD FINE THREAD

Diameter &

Thread Pitch

(Millimeters)

MARKING ON HEAD MARKING ON HEAD

Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9

N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft

6 x 1.0 10 mm 8 6 11 8 8 6 11 8 6 x 1.0

8 x 1.25 13 mm 20 15 27 20 21 16 29 22 8 x 1.0

10 x 1.5 16 mm 39 29 54 40 41 30 57 42 10 x 1.25

12 x 1.75 18 mm 68 50 94 70 75 55 103 76 12 x 1.25

14 x 2.0 21 mm 109 80 151 111 118 87 163 120 14 x 1.5

16 x 2.0 24 mm 169 125 234 173 181 133 250 184 16 x 1.5

18 x 2.5 27 mm 234 172 323 239 263 194 363 268 18 x 1.5

20 x 2.5 30 mm 330 244 457 337 367 270 507 374 20 x 1.5

22 x 2.5 34 mm 451 332 623 460 495 365 684 505 22 x 1.5

24 x 3.0 36 mm 571 421 790 583 623 459 861 635 24 x 2.0

30 x 3.0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2.0

Typical Washer

Installations

Lock Washer

Flat Washer

8/9/00

Bolt

Appendix 25

Bolt Torque & Size Charts (Rev. 10/10/2005)

BOLT SIZE CHART

NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

ABBREVIATIONS

AG ............................................................. Agriculture

ATF...............................Automatic Transmission Fluid

BSPP .......................... British Standard Pipe Parallel

BSPTM...............British Standard Pipe Tapered Male

CV .................................................. Constant Velocity

CCW ............................................ Counter-Clockwise

CW ............................................................. Clockwise

F..................................................................... Female

GA................................................................... Gauge

GR (5, etc.) ......................................... Grade (5, etc.)

HHCS.......................................Hex Head Cap Screw

HT ......................................................... Heat-Treated

JIC............... Joint Industry Council 37° Degree Flare

LH ...............................................................Left Hand

LT ......................................................................... Left

m ....................................................................... Meter

mm ..............................................................Millimeter

M ........................................................................ Male

MPa........................................................Mega Pascal

N .................................................................... Newton

NC ....................................................National Coarse

NF......................................................... National Fine

NPSM ...................National Pipe Straight Mechanical

NPT ........................................ National Pipe Tapered

NPT SWF ....... National Pipe Tapered Swivel Female

ORBM......................................... O-Ring Boss - Male

P .........................................................................Pitch

PBY .................................................... Power-Beyond

psi ........................................ Pounds per Square Inch

PTO ................................................... Power Take Off

QD ..................................................Quick Disconnect

RH ............................................................Right Hand

ROPS.......................... Roll-Over Protective Structure

RPM.......................................Revolutions Per Minute

RT ...................................................................... Right

SAE ........................Society of Automotive Engineers

UNC....................................................Unified Coarse

UNF ........................................................ Unified Fine

UNS ....................................................Unified Special

5/16 3/81/2 5/83/4 7/8

SAE Bolt Thread Sizes

MM 25 50 75 100 125 150 175

IN 1 7

Metric Bolt Thread Sizes

8MM 18MM14MM12MM10MM 16MM

234 56

F-8494 (Rev. 6/23/2005)

WARRANTY

(Replacement Parts For All Models Except Mow’n MachineTM

Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and

workmanship for a period of ninety (90) days from the date of delivery of the product to the original

purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a

period of 12 months.

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of

WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This

Warranty does not cover normal wear or tear, or normal maintenance items.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell

or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser

in any way. There are no third party beneficiaries of this Warranty.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of

charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with

this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)

days after such defect or noncompliance is discovered or should have been discovered, routed through

the dealer and distributor from whom the purchase was made, transportation charges prepaid.

WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the

product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF

REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS

WA RRA N TY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF

THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND

WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/

OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising

directly or indirectly from the product, whether such claim is based upon breach of contract, breach

of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality

of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or

goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for

labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to

obtain materials or manufacture replacement parts.

No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,

including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized

to alter, modify, or enlarge this Warranty.

Answers to any questions regarding warranty service and locations may be obtained by contacting:

3079 (Rev 10/21/2009)

Woods Equipment

Company

2606 South Illinois Route 2

Post Office Box 1000

Oregon, Illinois 61061 USA

800-319-6637 tel

800-399-6637 fax

www.WoodsEquipment.com

WARRANTY

(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)

Please Enter Information Below and Save for Future Reference.

Date Purchased: ____________________________ From (Dealer): __________________________________________

Model Number: ____________________________ Serial Number: __________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set

forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE

PRODUCT TO THE ORIGINAL PURCHASER.

All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.

The warranty periods for specific parts or conditions are listed below:

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to

improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been

materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized

service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made

with parts other than those obtainable through WOODS.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to

a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.

WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by

WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,

in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof

of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the

dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or

replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS

WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS

WARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS

MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY

OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the

product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal

theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,

revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute

machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture

replacement parts.

No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,

its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge

this Warranty. Answers to any questions regarding warranty service and locations may be obtained

Part or

Condition

Warranted

Model Number Duration (from date of delivery

to the original purchaser)

Gearbox

components

BW1260, BW1620, BW1800, BW2400 8 years

BW240HD, BW180HD, BW180HB, BW126HB 7 years

BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X,

BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240 6 years

PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,

RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,

9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH

5 years

RDC54, RD60, RD72, TBW150C 3 years (1 year if used in rental or

commercial applications)

Blade

spindles

RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,

9204RD-2 3 years

Rust-through

BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3,

BW180HB, BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260,

DSO1260, DS1440, TS1680

10 years

PART NO.

MAN0101

Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual

are the property of their respective companies or mark holders. Specifications subject to change without notice.

Woods Equipment Gill Str48S 2 Users Manual MAN0101

STR72S-2 to the manual 25145108-8ff1-43b6-a661-87e5761d38f1

Navigation menu

Versions of this User Manual:

Views

Navigation