Woods Equipment Lu126 Users Manual 111874 Loader Mounting Kit (LU126, LU132, 1020, 1027)

LU126 to the manual 6c5de27d-e6d9-4668-a024-f65e0a059ce4

2015-02-05

: Woods-Equipment Woods-Equipment-Lu126-Users-Manual-408539 woods-equipment-lu126-users-manual-408539 woods-equipment pdf

Open the PDF directly: View PDF .
Page Count: 38

INSTALLATION MANUAL

SAVE THIS

MANUAL!

Include it with

your Loader Manual.

It contains safety,

operation, and repair

part information

not found in other

manuals.

111874 LOADER MOUNTING KIT

for LU126, LU132, 1020, 1027 Loaders

on New Holland® Tractors

TN55, TN60A,TN65

TN70, TN70A, TN75, TN75A

and Case IH® Tractors:

JX1060C, JX1070C, JX1075C

includes Hose Kits

58025, 46945, 1010460

1023577, 1023583, 1023584

MAN0041

(Rev. 4/4/2008)

Tested. Proven. Unbeatable.

2 Introduction

LMK (Rev. 7/20/2007)

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions

and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’s

Manual are completed before releasing equipment to the owner.

TO THE OWNER:

Read this manual and Loader Operator’s Manual before operating your Woods equipment. The information presented

will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read

this manual carefully and become acquainted with all adjustment and operating procedures before attempting to

operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer

Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and

satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.

Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary

tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for

safe and satisfactory operation. Record the model number of your equipment in the space provided.

Model: _______________________________ Date of Purchase: _____________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.

The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with

an exclamation mark) to indicate the degree of hazard for items of personal safety.

Safety 3

Loader Mounting Kit SR3 (4/25/2003)

INSTALLATION

This Loader Mounting Kit is to be used only for

the loaders and tractors specified in this manual.

Any other use or modification of this mounting kit

may result in serious injury or death.

Hydraulics must be connected as instructed in

this manual. Do not substitute parts, modify, or

connect in any other way.

After connecting hoses, check that all control

lever positions function as instructed in the Opera-

tor's Manual. Do not put into service until control

lever and equipment movements are correct.

Safety instructions are important! Read all

attachment and power unit manuals; follow all

safety rules and safety decal information. (Replace-

ment manuals and safety decals are available from

your dealer. To locate your nearest dealer, check

the Dealer Locator at www.WoodsEquipment.com,

or in the United States and Canada call 1-800-319-

6637.) Failure to follow instructions or safety rules

can result in serious injury or death.

Keep hands and body away from pressurized

lines. Use paper or cardboard, not hands or other

body parts to check for leaks. Wear safety goggles.

Hydraulic fluid under pressure can easily penetrate

skin and will cause serious injury or death.

Make sure that all operating and service person-

nel know that if hydraulic fluid penetrates skin, it

must be surgically removed as soon as possible by

a doctor familiar with this form of injury or gan-

grene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID

ENTERS SKIN OR EYES. DO NOT DELAY.

Check that all hardware is properly installed.

Always tighten to torque chart specifications

unless instructed otherwise in this manual.

Air in hydraulic systems can cause erratic oper-

ation and allows loads or equipment components

to drop unexpectedly. When connecting equipment

or hoses or performing any hydraulic maintenance,

purge any air in hydraulic system by operating all

hydraulic functions several times. Do this before

putting into service or allowing anyone to

approach the equipment.

Protective hose sleeves must cover all hydrau-

lic hoses within 20 inches of the operator and be

secured onto metal hose fittings. Replace hoses or

sleeves if damaged or if protective sleeve cannot

be properly positioned or secured.

Make sure all hydraulic hoses, fittings, and

valves are in good condition and not leaking before

starting power unit or using equipment. Check and

route hoses carefully to prevent damage. Hoses

must not be twisted, bent sharply, kinked, frayed,

pinched, or come into contact with any moving

parts. Operate moveable components through full

operational range to check clearances. Replace

any damaged hoses immediately.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

Do not modify or alter or permit anyone else to

modify or alter the equipment or any of its compo-

nents in any way.

Do not allow bystanders in the area when oper-

ating, attaching, removing, assembling, or servic-

ing equipment.

Use a suitable lifting device of sufficient capac-

ity. Use adequate personnel to handle heavy com-

ponents.

Keep all persons away from operator control

area while performing adjustments, service, or

maintenance.

Safety is a primary concern in the design and

manufacture of our products. Unfortunately, our

efforts to provide safe equipment can be wiped

out by an operator’s single careless act.

In addition to the design and configuration of

equipment, hazard control and accident preven-

tion are dependent upon the awareness, con-

cern, judgement, and proper training of

personnel involved in the operation, transport,

maintenance, and storage of equipment.

It has been said, “The best safety device is an

informed, careful operator.” We ask you to be

that kind of operator.

Si no lee Ingles, pida ayuda a

alguien que si lo lea para que le

traduzca las medidas de seguridad.

LEA EL INSTRUCTIVO!

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

4 Mount Installation

MAN0041 (Rev. 4/4/2008)

LOADER MOUNT INSTALLATION

■ Only use 111874 Loader Mounting Kit for

mounting Woods LU126, LU132, 1020, 1027 loaders

on New Holland® TN55, TN60A TN65, TN70, TN70A,

TN75, TN75A tractors and Case IH® JX1060C,

JX1070C, and JX1075C tractors. Any other use or

modification of this mounting kit may result in seri-

ous injury or death.

Safety instructions are important! Read all

attachment and power unit manuals; follow all

safety rules and safety decal information. (Replace-

ment manuals and safety decals are available from

your dealer. To locate your nearest dealer, check

the Dealer Locator at www.WoodsEquipment.com,

or in the United States and Canada call 1-800-319-

6637.) Failure to follow instructions or safety rules

can result in serious injury or death.

Do not modify or alter or permit anyone else to

modify or alter the equipment or any of its compo-

nents in any way.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

If you do not understand any part of this manual

and need assistance, see your dealer.

NOTICE

■ This equipment must be assembled and

installed on the customer’s tractor by the Woods

dealer. Dealer must thoroughly inspect equipment

and complete each item on the PRE-DELIVERY

CHECK LIST, DELIVERY CHECK LIST, and PROD-

UCT REGISTRATION from the loader manual

before equipment is released to the customer.

CAUTION

Tractor Preparation

For installing this mounting kit, references to right, left,

forward, and rearward directions are determined from

the operator’s position in the tractor seat.

1. Remove the tractor front weights and front fend-

ers, if equipped.

2. Rotate the exhaust pipe opening to face away

from the left side of the tractor.

NOTE: On TNA models the tip of the exhaust

pipe will have to be removed and a weather cap

installed. See page 6 for installation instructions.

3. Set the tractor wheels to the manufacturer’s

widest recommended spacing. Refer to the

tractor operator’s manual.

NOTICE

■ Clean threaded holes in the tractor chassis

thoroughly, using a tap of the proper size. Paint,

rust, or debris in the threads may not permit cap

screws to be installed and tightened correctly.

As a valued customer, Woods appreciates your comments. Once loader mount and

hydraulic hoses have been installed, please take a few minutes to complete the Loader

Mount Evaluation sheet that was supplied with this mount. Your comments will help us

continue to bring you quality products.

Mount Installation 5

MAN0041 (Rev.4/4/2008)

Install Right and Left Rear Mounts

1. Attach right rear mount (1) to tractor.

2. Secure using one cap screw (7) and hardened flat

washer (9) in the top hole.

3. Secure to bottom holes using two cap screws (8)

and hardened flat washers (9).

4. Secure to forward holes using two cap screws (5)

and hardened flat washers (9).

5. Repeat steps to install left rear mount (2). See

Figure 2.

6. Tighten all hardware to specifications listed on

page 6.

1. 1000468 Right rear mount

2. 1000469 Left rear mount

5. 307553 M20 x 2.5P x 50 mm HHCS

7. 1001377 M20 x 2.5P x 40 mm HHCS

8. 21413 M20 x 2.5P x 70 mm HHCS

9. 57798 3/4 Hardened flat washer.

Figure 1. Right Rear Mount Installed

Figure 2. Left Rear Mount Installed

Install Grill Guard (Optional)

1. Install grill guard (4) to front of tractor chassis,

using four cap screws (5) and lock washers (6) as

shown.

2. Torque hardware to specifications given on

page 6.

4. 40449 Grill guard

5. 307553 M20 x 2.5P x 50 mm HHCS

6. 21531 M20 Lock washer

Figure 3. Grill Guard Installed

6 Mount Installation

MAN0041 (Rev. 4/4/2008)

Torque Hardware

Torque all hardware to specifications listed below.

NOTICE

■ Check torque value of mount hardware after

10 hours of operation and again after every 50

hours of operation.

Install Weather Cap on Exhaust Pipe

NOTE: After the hydraulics and loader are install on

the tractor, check the clearance between the top of

the exhaust pipe and the loader boom when the

loader is raised. If there is interference, a weather cap

will need to be installed.

1. Remove exhaust pipe from the tractor. Save

hardware for later use.

2. Remove approximately 6-inches from the top of

the exhaust pipe.

3. Attach exhaust pipe to the tractor. Make sure that

the support flange on the exhaust pipe is between

the tractor and the support bracket as shown in

page 6. Secure using hardware previously

removed.

4. Attach weather cap to the top of the exhaust pipe

with supplied hardware. Position cap hinge to the

rear. See Figure 5. Weather cap is included in the

loader mount kit.

Figure 4. Exhaust Pipe Reinstalled

Figure 5. Weather Cap Installed

TORQUE SPECIFICATIONS

Ref. Cap Screw Qty Wrench

Size

Required Torque

7 M20 x 2.5P x 40 mm 2 30 mm 244 lbs-ft. (330 N-m)

5 M20 x 2.5P x 50 mm 8 30 mm 244 lbs-ft. (330 N-m)

8 M20 x 2.5P x 70 mm 4 30 mm 244 lbs-ft. (330 N-m)

DP7

Forward

DP8

Hydraulic Installation 7

MAN0041 (Rev. 4/4/2008)

HOSE KIT INSTALLATION

Keep hands and body away from pressurized

lines. Use paper or cardboard, not hands or other

body parts to check for leaks. Wear safety goggles.

Hydraulic fluid under pressure can easily penetrate

skin and will cause serious injury or death.

Make sure that all operating and service person-

nel know that if hydraulic fluid penetrates skin, it

must be surgically removed as soon as possible by

a doctor familiar with this form of injury or gan-

grene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID

ENTERS SKIN OR EYES. DO NOT DELAY.

Air in hydraulic systems can cause erratic oper-

ation and allows loads or equipment components

to drop unexpectedly. When connecting equipment

or hoses or performing any hydraulic maintenance,

purge any air in hydraulic system by operating all

hydraulic functions several times. Do this before

putting into service or allowing anyone to

approach the equipment.

Protective hose sleeves must cover all hydrau-

lic hoses within 20 inches of the operator and be

secured onto metal hose fittings. Replace hoses or

sleeves if damaged or if protective sleeve cannot

be properly positioned or secured.

Make sure all hydraulic hoses, fittings, and

valves are in good condition and not leaking before

starting power unit or using equipment. Check and

route hoses carefully to prevent damage. Hoses

must not be twisted, bent sharply, kinked, frayed,

pinched, or come into contact with any moving

parts. Operate moveable components through full

operational range to check clearances. Replace

any damaged hoses immediately.

58025 Hose Kit Installation - - - - - - - - - - - - - - Page 7

46945 Hose Kit Installation- - - - - - - - - - - - - - Page 11

1010460 Hose Kit Installation- - - - - - - - - - - - Page 16

1023577 Hose Kit Installation- - - - - - - - - - - - Page 19

1023584 Hose Kit Installation- - - - - - - - - - - - Page 22

1023583 Hose Kit Installation- - - - - - - - - - - - Page 24

58025 HOSE KIT

General Description

These set up instructions are for operating the 1020,

1027 loader using the tractor hydraulic remote control

levers. To use this hydraulic connection the tractor

must be equipped with either two hydraulic levers or a

joystick control and four tractor hydraulic couplers as

shown (Figure 5).

Hydraulic quick couplers for connection to tractor are

NOT INCLUDED with hose kits, but are available as

service parts.

NOTE: After the hydraulics and loader are installed

on the tractor, check the clearance between the top of

the exhaust pipe and the loader boom when the

loader is raised. If there is interference, a weather cap

will need to be installed. See Page 6 for installation

instructions. Figure 6. Connections to Tractor Hydraulic Couplers

(Typical)

8 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

58025 Hose Kit

Assemble and Route Hoses

1. Attach a 90-degree elbow (2) and male quick cou-

pler (3) to each loader supply hose (1).

2. Connect loader supply hoses to loader feedlines

as shown in Figure 7.

3. Route hydraulic hoses along loader mount, under

the right side of operator's platform, and over the

rear axle. See Figure 8.

NOTE: Hoses must be routed so that they are not

pinched, bent sharply, or chafed during operation.

Hoses must not interfere with any tractor control

operation or contact any moving parts.

1. 53670 Hose, 150" x 3/4 JICM x 3/4 JICM

2. 313053 Elbow, 3/4 JICF x 1/2 NPTM 90°

3. -------- Quick coupler, Male (not supplied)

Figure 7. Loader Feedline Connection

Figure 8. Hose Routing (Typical Installation)

Hydraulic Installation 9

MAN0041 (Rev. 4/4/2008)

58025 Hose Kit

Connect Hoses to Tractor

1. Connect hoses to the tractor hydraulic couplers

as shown in Figure 9.

Figure 9. Hose Connection to Tractor

Hydraulic Couplers (Typical)

Install Hose Hangers

1. Install hose hangers beneath the tractor chassis.

NOTE: For forward hanger, use hardware pro-

vided in kit; for rearward hanger, use tractor hard-

ware.

2. Route hoses through hose hangers as shown and

attach lock pins to retain hoses.

3. Torque hardware to 15 lbs.-ft.

6. 30577 M8 x 1.25P x 25 mm HHCS

7. 2472 5/16 Lock washer

8. 58033 Hose hanger

9. 58047 1/4 x 2-1/2 Lock pin Figure 10. Hose Hangers Installed

Figure 11. Hose Hanger Installation

CM2683

10 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

58025 Hose Kit

Verify Control Movements

1. Mount loader to tractor: Remove mount pins

from loader uprights. Align tractor with loader and

slowly drive tractor into loader. Shut off tractor.

2. Connect loader feedline hoses to tractor remote

control couplers. See Figure 9.

3. Comply with all safety rules and start the tractor.

4. Mount loader to tractor by activating bucket

cylinders to raise or lower the loader uprights into

the loader mounts. Slowly advance tractor

forward, activating appropriate cylinders to

engage loader completely into mounts. Insert

mounting pins to secure loader.

5. Check that all hydraulic control lever positions

operate the loader movements correctly as

shown in Figure 12.

6. If loader movements do not respond correctly,

shut off tractor, relieve pressure, and reconnect

properly. Loader control movements must be

correct before proceeding.

7. Once all loader functions are correct, start the

tractor and operate the loader to check for leaks.

Purge any remaining air from the hydraulic

system and check oil level.

8. When hose routings and correct loader

operations are verified, identify each circuit by

placing a matching colored band around the male

and female quick couplers. The color-coded

bands will make reinstallation easier when the

loader is removed from tractor.

9. Be sure that adequate slack is left in the hoses so

they can move as the loader moves through its

full range of motion.

10. Attach the plastic tie straps (included in kit) every

20-inches around the hoses to keep them tightly

bundled and away from contact with the ground

or other moving parts on the tractor or loader.

11. Before operating the loader, make sure that the

Pre-Delivery, Delivery, and Pre-Operation

Checklists from the Operator section in the

Loader Operator’s Manual have been completed.

Figure 12. Tractor Hydraulic Control Levers

CM1570

Control 2

Control 1

DP1

●Control 1, Handle forward - Boom down

●Control 1, Handle back - Boom up

●Control 2, Handle forward - Dump bucket

or attachment

●Control 2, Handle back - Rollback bucket

or attachment

Hydraulic Installation 11

MAN0041 (Rev. 4/4/2008)

46945 HOSE KIT

General Description

These set up instructions are for operating the 1020,

1027 loader using single lever control valve mounted

to the loader rear mount as shown in Figure 13. To

use this hydraulic connection the hoses must be con-

nected between the control valve and the tractor

hydraulic system located at the rear of the tractor.

NOTE: After the hydraulics and loader are install on

the tractor, check the clearance between the top of

the exhaust pipe and the loader boom when the

loader is raised. If there is interference, a weather cap

will need to be installed. See Page 6 for installation

instructions.

NOTICE

■ If hydraulic lines are not connected as shown

in this manual, the control valve may be damaged.

A blocked outlet (RETURN) or improper hose con-

nection will cause pressurized oil to enter the

return circuit and damage the valve.

Figure 13. Control Valve Installed

Adjust Control Valve

The control valve comes standard with two OUT

ports. One at the lower left corner and one at the

upper right corner. The port at the lower left is shipped

with a 3/4 JICM x 7/8 O-ring adapter installed. The

port at the upper right is shipped with a 7/8 O-ring

plug.

Remove plug installed in the upper right port. Remove

adapter from lower left port. Install plug in lower left

port and adapter in upper right port. Control valve

should have IN, OUT and PBY ports arranged as

shown in Figure 14.

Attach control valve and bracket to loader mount

before proceeding. Figure 14. Correct Control Valve Arrangement

Install Hose Guide

1. Attach hose guide (7) to the outer hole on the

bracket in front to the brake peddle.

2. Secure into place using cap screw (8) as shown

in Figure 15. Torque to 30 lbs.-ft. using a 16mm

wrench.

7. 54305 Hose guide

8. 307203 M10 x 1.25P x 35 mm HHCS

Figure 15. Hose Guide Installed

DP2

12 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

46945 Hose Kit

Attach Hoses to Control Valve

NOTICE

■ If hydraulic lines are not connected as shown

in the mount installation manual or tractor man-

ual, the loader control valve may be damaged. A

blocked outlet (RETURN) or improper hose con-

nection will cause pressurized oil to enter the

return circuit and damage the valve or the tractor

hydraulic system.

1. Attach 90° end of hoses (2) to the IN, OUT, and

PBY ports on the control valve.

2. Route hoses over hose guide (as shown in Figure

15), under right side of platform, and over right

rear axle.

2. 46947 Hose, 120” x 3/4 JICF x 7/8 JICF

Figure 16. Control Valve Hose Connections

Install Hydraulic Fittings and Hoses

1. Locate the hydraulic ports on the rear of the trac-

tor as shown in Figure 17.

2. Remove tube and fittings from the PBY,

PRESSURE, and RETURN ports.

Figure 17. Tractor Hydraulic Connections

PRESSURE

PBY

RETURN

DP3

Hydraulic Installation 13

MAN0041 (Rev. 4/4/2008)

46945 Hose Kit

Install Hydraulic Fitting and Hoses

(Continued)

3. Install adapter (3) and elbow (5) to the RETURN

port.

4. Install elbow (6) to the PRESSURE port.

5. Install adapter (4) and elbow (5) to the PBY port.

6. Attach hose from the IN port on the control valve

to elbow (6) in the PRESSURE port on the tractor.

7. Attach hose from the PBY port on the control

valve to elbow (5) in the PBY port on the tractor.

8. Attach the hose from the OUT port on the control

valve to elbow (5) in the RETURN port on the

tractor.

9. Position the hoses as shown in Figure 19.

3. 58081 Adapter, M22 x 1.5P x 7/8 JICM

4. 58647 Adapter, M18 x 1.5P x 7/8 JICM

5. 315024 Elbow, 7/8 JICM x 7/8 JICF

6. 46054 Elbow, 7/8 JICF x 7/8 JICF 45°

Figure 18. Hydraulic Fitting and Hose Installation

Figure 19. Hydraulic Fittings and Hoses Installed

PBY

PRESSURE

RETURN

14 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

46945 Hose Kit

Install Hose Hanger

1. Remove lower bolt, washers, and nut that

secures right fender to the ROPS.

2. Keep larger washer and discard the remaining

hardware.

3. Attach hose hanger (9), using spacer (10), cap

screw (12), flat washer (from tractor), lock washer

(13), and nut (14) as shown in Figure 20 and

Figure 21.

4. Route PRESSURE and PBY hoses through

hanger as shown in Figure 21.

5. Secure hoses into position using lock pin (11).

6. Route RETURN hose as shown in Figure 19 to

avoid upper 3-point arms.

7. Tighten all hydraulic fittings securely.

9. 58280 Hose hanger

10. 46948 Spacer

11. 58047 Lock pin

12. 31138 3/8 NC x 3-1/2 HHCS

13. 838 3/8 Lock washer

14. 835 3/8 NC Hex nut

Figure 20. Hose Hanger Installation

Figure 21. Hose Hanger Installed

Connect Work Port Hoses

1. The control valve kit contains hoses assembled

with quick couplers. Attach supply hoses to

loader feedlines, following the color scheme

shown in Figure 22.

2. Connect loader supply hoses to control valve

hydraulic couplers when attaching loader.

Figure 22. 1020, 1027 Control Valve and Loader Feedline Hose Connections

11 9

DP5

Hydraulic Installation 15

MAN0041 (Rev. 4/4/2008)

46945 Hose Kit

Verification of Control Movements

1. Mount loader to tractor: Remove mount pins

from loader uprights. Align tractor with loader and

lowly drive tractor into loader. Shut off tractor.

2. Connect loader feedline hoses to control valve

hydraulic couplers (See Figure 22).

NOTE: At least 6” spacing should be maintained

between valve, bracket, or hoses and any tractor

control (brake pedals, accelerator, hand throttle,

or hydraulic levers).

3. Comply with all Safety Rules and start the tractor.

4. Mount loader to tractor by activating bucket

cylinders to raise or lower the loader uprights into

the loader mounts. Slowly advance tractor

forward, activating appropriate cylinders to

engage loader completely into mounts. Insert

mounting pins to secure loader.

5. Check that all hydraulic control lever positions

operate the loader movements correctly as

shown in Figure 23.

6. If loader movements do not respond correctly,

shut off tractor, relieve pressure, and reconnect

properly. Loader control movements must be

correct before proceeding.

7. Once all loader functions are correct, start the

tractor and operate the loader to check for leaks.

Purge any remaining air from the hydraulic

system.

8. When hose routings and correct loader

operations are verified, identify each circuit by

placing a matching colored band around the male

and female quick-disconnect coupler set. The

colored bands will make re-installation easier

when the loader is remove from the tractor.

9. Be sure the adequate slack is left in the hoses so

they can move as the loader moves through its

full range of motion.

10. Attach plastic tie straps every 20" around the

hoses to keep them tightly bound and away from

contact with the ground or other moving parts on

tractor.

11. Before operating the loader, make sure that the

Pre-Delivery, Delivery, and Pre-Operation

Checklists from the Operation section in the

Loader Operator’s Manual have been completed.

Figure 23. Single Lever Control Operation

●Handle forward - Boom down

●Handle forward to limit - Float position

●Handle back - Boom up

●Handle right - Dump bucket

or attachment (slow)

●Handle right to limit - Dump bucket

or attachment (fast)

●Handle to left - Rollback bucket or attachment

16 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

1010460 HOSE KIT

General Description

These set-up instructions are for operating the 1020,

1027 loader using the tractor hydraulic remote control

lever. To use this hydraulic connection, the tractor

must be equipped with a multi-function hydraulic con-

trol valve and remote control lever. The control valve

is located on the right side of the tractor beneath the

operator platform.

NOTE: After the hydraulics and loader are installed

on the tractor, check the clearance between the top of

the exhaust pipe and the loader boom when the

loader is raised. If there is interference, a weather cap

will need to be installed. See Page 6 for installation

instructions.

Figure 24. Tractor Hydraulic Control Lever and Valve

Install Hydraulic Fitting to Tractor Valve

1. Locate the tractor hydraulic valve under the right

side of the tractor platform.

2. Install adapters (1), adapter (3), and female half

of quick coupler set (5) to each of the tractor valve

ports. See Figure 7 and Figure 8.

NOTE: Not all parts supplied with this hose kit are

used for this application.

1. 1010920 Adapter, M22 x 1.5 x 3/4 JICM

3. 315036 Adapter, 3/8 NPTM x 3/4 JICF

5. 316007 Quick coupler set, male & female

Figure 25. Hydraulic Fittings Installed Figure 26. Hydraulic Fitting Installation

Hydraulic Installation 17

MAN0041 (Rev. 4/4/2008)

1010460 Hose Kit

Assemble Loader Hoses

1. Attach male half of quick coupler set (5) and

elbow (2) to each of the loader feedline hoses (4).

See Figure 27.

2. Attach loader feedline hoses to the steel feedlines

on the loader boom. See Figure 28.

3. Route hydraulic hoses along loader mount and

under the right side of operator's platform to the

tractor valve.

NOTE: Be sure to avoid contact with brake ped-

als and other moveable tractor components.

Hoses must be routed so that they are not

pinched, bent sharply, or chafed during operation.

Hoses must not interfere with any tractor control

operation or contact any moving parts.

2. 313015 Elbow, 3/8 NPTM x 3/8 NPTF 45°

4. 1009513 Hose, 76" x 3/8 NPTM x 3/4 JICM

5. 316007 Quick coupler set, male & female

Figure 27. Loader Hose Connection

Figure 28. Loader Feedline Connection

Connect Hoses to Tractor Valve

Connect hoses to the hydraulic quick couplers as

shown in Figure 29.

Figure 29. Hydraulic Hose Connection to

Tractor Valve

DP9

18 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

1010460 Hose Kit

Verification of Control Movements

1. Mount loader to tractor: Remove mount pins

from loader uprights. Align tractor with loader and

lowly drive tractor into loader. Shut off tractor.

2. Connect loader feedline hoses to control valve

hydraulic couplers (See Figure 29).

NOTE: At least 6" spacing should be maintained

between valve, bracket, or hoses and any tractor

control (brake pedals, accelerator, hand throttle,

or hydraulic levers).

3. Comply with all Safety Rules and start the tractor.

4. Mount loader to tractor by activating bucket

cylinders to raise or lower the loader uprights into

the loader mounts. Slowly advance tractor

forward, activating appropriate cylinders to

engage loader completely into mounts. Insert

mounting pins to secure loader.

5. Check that all hydraulic control lever positions

operate the loader movements correctly as

shown in Figure 30.

6. If loader movements do not respond correctly,

shut off tractor, relieve pressure, and reconnect

properly. Loader control movements must be

correct before proceeding.

7. Once all loader functions are correct, start the

tractor and operate the loader to check for leaks.

Purge any remaining air from the hydraulic

system.

8. When hose routings and correct loader

operations are verified, identify each circuit by

placing a matching colored band around the male

and female quick-disconnect coupler set. The

colored bands will make re-installation easier

when the loader is remove from the tractor.

9. Be sure the adequate slack is left in the hoses so

they can move as the loader moves through its

full range of motion.

10. Attach plastic tie straps every 20" around the

hoses to keep them tightly bound and away from

contact with the ground or other moving parts on

tractor.

11. Before operating the loader, make sure that the

Pre-Delivery, Delivery, and Pre-Operation

Checklists from the Operation section in the

Loader Operator’s Manual have been completed.

Figure 30. Single Lever Control Operation

●Handle forward - Boom down

●Handle forward to limit - Float position

●Handle back - Boom up

●Handle right - Dump bucket or attachment

●Handle to left - Rollback bucket or attachment

Hydraulic Installation 19

MAN0041 (Rev. 4/4/2008)

1023577 HOSE KIT

General Description

These set-up instructions are for operating the LU126

or LU132 loader using the tractor hydraulic remote

control lever. To use this hydraulic connection, the

tractor must be equipped with a multi-function hydrau-

lic control valve and remote control lever. The control

valve is located on the right side of the tractor

beneath the operator platform.

Figure 31. Tractor Remote Control Lever

Install Hydraulic Fitting to Tractor Valve

1. Locate the tractor hydraulic valve under the right

side of the tractor platform.

2. Install adapters (1), adapter (3), and female half

of quick coupler set (5) to each of the tractor valve

ports. See Figure 32 and Figure 33.

NOTE: Not all parts supplied with this hose kit are

used for this application.

1. 1010920 Adapter, M22 x 1.5 x 3/4 JICM

3. 315036 Adapter, 3/8 NPTM x 3/4 JICF

5. 316007 Quick coupler set, male & female

Figure 32. Hydraulic Fittings Installed Figure 33. Hydraulic Fitting Installation

DP1

DP4

20 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

1023577 Hose Kit

Assemble Loader Hoses

1. Attach male half of quick coupler set (5) and

elbow (2) to each of the loader feedline hoses (4).

See Figure 34

2. Attach loader feedline hoses to the steel feedlines

on the loader boom. See Figure 35.

3. Route hydraulic hoses along loader mount and

under the right side of operator's platform to the

tractor valve.

NOTE: Be sure to avoid contact with brake ped-

als and other moveable tractor components.

Hoses must be routed so that they are not

pinched, bent sharply, or chafed during operation.

Hoses must not interfere with any tractor control

operation or contact any moving parts.

2. 313015 Elbow, 3/8 NPTM x 3/8 NPTF 45°

4. 1022986 Hose, 116" x 3/8 NPTM x 3/4 JICM

5. 316007 Quick coupler set, male & female

Figure 34. Loader Hose Connection

Figure 35. Loader Feedline Connection

Connect Hoses to Tractor Valve

Connect hoses to the hydraulic quick couplers as

shown in Figure 36.

Figure 36. Hydraulic Hose Connection to

Tractor Valve

DP9

Hydraulic Installation 21

MAN0041 (Rev. 4/4/2008)

1023577 Hose Kit

Verification of Control Movements

1. Mount loader to tractor: Remove mount pins

from loader uprights. Align tractor with loader and

lowly drive tractor into loader. Shut off tractor.

2. Connect loader feedline hoses to control valve

hydraulic couplers (See Figure 36).

NOTE: At least 6" spacing should be maintained

between valve, bracket, or hoses and any tractor

control (brake pedals, accelerator, hand throttle,

or hydraulic levers).

3. Comply with all Safety Rules and start the tractor.

4. Mount loader to tractor by activating bucket

cylinders to raise or lower the loader uprights into

the loader mounts. Slowly advance tractor

forward, activating appropriate cylinders to

engage loader completely into mounts. Insert

mounting pins to secure loader.

5. Check that all hydraulic control lever positions

operate the loader movements correctly as

shown in Figure 37.

6. If loader movements do not respond correctly,

shut off tractor, relieve pressure, and reconnect

properly. Loader control movements must be

correct before proceeding.

7. Once all loader functions are correct, start the

tractor and operate the loader to check for leaks.

Purge any remaining air from the hydraulic

system.

8. When hose routings and correct loader

operations are verified, identify each circuit by

placing a matching colored band around the male

and female quick-disconnect coupler set. The

colored bands will make re-installation easier

when the loader is remove from the tractor.

9. Be sure the adequate slack is left in the hoses so

they can move as the loader moves through its

full range of motion.

10. Attach plastic tie straps every 20" around the

hoses to keep them tightly bound and away from

contact with the ground or other moving parts on

tractor.

11. Before operating the loader, make sure that the

Pre-Delivery, Delivery, and Pre-Operation

Checklists from the Operation section in the

Loader Operator’s Manual have been completed.

Figure 37. Single Lever Control Operation

●Handle forward - Boom down

●Handle forward to limit - Float position

●Handle back - Boom up

●Handle right - Dump bucket or attachment

●Handle to left - Rollback bucket or attachment

22 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

1023584 HOSE KIT

General Description

These set-up instructions are for operating the LU126

or LU132 loader using the tractor hydraulics. To use

this connection, the tractor must be equipped with two

hydraulic levers and four tractor hydraulic couplers at

the rear of the tractor as shown in Figure 38.

NOTE: The male hydraulic quick couplers for connec-

tion to tractor are NOT INCLUDED with this hose kit

but are available as service parts.

NOTE: After the hydraulics and loader are installed

on the tractor, check the clearance between the top of

the exhaust pipe and the loader boom when the

loader is raised. If there is interference, a weather cap

will need to be installed. See Page 6 for installation

instructions.

Figure 38. Tractor Rear Hydraulic Couplers (Typical)

Assemble Hoses

1. Attach a 90-degree elbow (2) and male quick

coupler (3) to each loader supply hose (1). See

Figure 39.

2. Connect loader supply hoses to loader feedlines

as shown in Figure 40.

3. Route hoses along right mount, under the

cab/operator’s platform, and over right rear axle.

Be sure to avoid contact with 3-point linkage,

brake pedals, and other moveable tractor

components. Hoses must be routed so that they

are not pinched, bent sharply, or chafed during

operation.

1. 1023493 Hose, 200" x 3/4 JICM x 3/4 JICM

2. 313053 Elbow, 3/4 JICF x 1/2 NPTM 90°

3. -------- Quick coupler, male

(not included in kit)

Figure 39. Hose Assembly

Figure 40. Loader Feedline Connections

DP12

Hydraulic Installation 23

MAN0041 (Rev. 4/4/2008)

1023584 Hose Kit

Install Hose Hanger

1. Remove a bolt from the bottom of right

cab/operator’s platform support.

2. Attach hose hanger (4) and secure with tractor

hardware previously removed.

3. Place hoses in hose hanger when routing

hydraulic hoses to the tractor hydraulic couplers.

4. Secure hoses in position using lock pin (5).

4. 59520 Hose hanger

5. 58047 1/4 x 2-1/2 Lock pin

* Tractor hardware Figure 41. Hose Hanger Installation

Verify Control Movements

1. Mount loader to tractor: Remove mount pins

from loader uprights. Align tractor with loader and

slowly drive tractor into loader. Shut off tractor.

2. Connect loader feedline hoses to tractor remote

control couplers. See Figure 42.

3. Comply with all safety rules and start the tractor.

4. Mount loader to tractor by activating bucket

cylinders to raise or lower the loader uprights into

the loader mounts. Slowly advance tractor

forward, activating appropriate cylinders to

engage loader completely into mounts. Insert

mounting pins to secure loader.

5. Check that all tractor hydraulic control lever

positions operate the loader movements correctly.

6. If loader movements do not respond correctly,

shut off tractor, relieve pressure, and reconnect

properly. Loader control movements must be

correct before proceeding.

7. Once all loader functions are correct, start the

tractor and operate the loader to check for leaks.

Purge any remaining air from the hydraulic

system and check oil level.

8. When hose routings and correct loader

operations are verified, identify each circuit by

placing a matching colored band around the male

and female quick-disconnect coupler. The color-

coded bands will make reinstallation easier when

the loader is removed from the tractor.

9. Be sure that adequate slack is left in the hoses so

they can move as the loader moves through its

full range of motion.

10. Attach the plastic tie straps (included in kit) every

20-inches around the hoses to keep them tightly

bundled and away from contact with the ground

or other moving parts on the tractor or loader.

11. Before operating the loader, make sure that the

Pre-Delivery, Delivery, and Pre-Operation Check

Lists in the Loader Operator’s Manual have been

completed.

Figure 42. Loader Feedline to Tractor Remote Coupler Connections

24 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

1023583 HOSE KIT

General Description

These set up instructions are for operating the LU126

or LU132 loader using single lever control valve

mounted to the right loader mount as shown in Figure

43. To use this hydraulic connection the hoses must

be connected between the control valve and the trac-

tor hydraulic system located at the rear of the tractor.

NOTE: After the hydraulics and loader are install on

the tractor, check the clearance between the top of

the exhaust pipe and the loader boom when the

loader is raised. If there is interference, a weather cap

will need to be installed. See Page 6 for installation

instructions.

NOTICE

■ If hydraulic lines are not connected as shown

in this manual, the control valve may be damaged.

A blocked outlet (RETURN) or improper hose con-

nection will cause pressurized oil to enter the

return circuit and damage the valve.

Figure 43. Control Valve Installed (Typical)

Install Hydraulic Fittings to Control Valve

1. Remove open-center plug from the side of the

control valve.

2. Install PBY conversion plug (18) and elbow (17),

supplied with hose kit, into the side of the control

valve.

3. Attach elbow (5) to the fitting in the IN port of the

control valve.

5. 313032 Elbow, 3/4 JICM x 3/4 JICF 90°

17. 60 Elbow, 3/4 JICM x 7/8 ORBM

18. 346143 Power-Beyond conversion plug

Figure 44. Cable Control Valve Fitting Installation

DP10

Hydraulic Installation 25

MAN0041 (Rev. 4/4/2008)

1023583 Hose Kit

Install Hydraulic Fittings and Hoses

1. Locate the hydraulic ports on the rear of the trac-

tor.

2. Remove tube and fittings from the PBY,

PRESSURE, and RETURN ports shown in Figure

45.

3. Install adapter (4) in the PBY port, adapter (3)

and elbow (5) in the RETURN port and elbow (6)

in the PRESSURE port.

4. Attach straight end of hose (1) to the PBY port on

the control valve.

5. Attach 90° end of second hose (1) to the OUT

port on the control valve.

6. Attach one end of hose (2) to the IN port on the

control valve.

7. Route hoses under right side of platform, over

right rear axle and out the back of the tractor.

8. Attach straight end of hose (1) from the OUT port

on the control valve to the elbow (5) in the

RETURN port on the back of the tractor.

9. Attach end of hose (2) from the IN port on the

control valve to the PRESSURE port on the back

of the tractor.

10. Attach 90° end of hose (1) from the PBY port on

the control valve to the PBY port on the back of

the tractor.

Figure 45. Tractor Hydraulic Connections

Figure 46. Hydraulic Fittings and Hose Connections

Figure 47. Hydraulic Fittings and Hose Installation

PRESSURE

PBY

RETURN

DP3

Tube

PBY

PRESSURE

RETURN

DP11

1. 1002862 Hose, 120" x 3/4 JICF x 3/4 JICF 90°

2. 1023496 Hose, 120" x 3/4 JICF x 7/8 JICF

3. 1010920 Adapter, M22 x 1.5P x 3/4 JICM

4. 44426 Adapter, M18 x 1.5P x 3/4 JICM

5. 313032 Elbow, 3/4 JICM x 3/4 JICF 90°

6. 46054 Elbow, 7/8 JICM x 7/8 JICF 45°

26 Hydraulic Installation

MAN0041 (Rev. 4/4/2008)

1023583 Hose Kit

Install Hose Hanger

1. Remove lower bolt, washers, and nut that

secures right fender to the ROPS.

2. Keep larger washer and discard the remaining

hardware.

3. Attach hose hanger (9), using spacer (10), cap

screw (12), flat washer (from tractor), lock washer

(13), and nut (14) as shown in Figure 48 and

Figure 49.

4. Route PRESSURE and PBY hoses through

hanger as shown in Figure 49.

5. Secure hoses into position using lock pin (11).

6. Tighten all hydraulic fittings securely.

9. 58280 Hose hanger

10. 46948 Spacer

11. 58047 Lock pin

12. 31138 3/8 NC x 3-1/2 HHCS

13. 838 3/8 Lock washer

14. 835 3/8 NC Hex nut

Figure 48. Hose Hanger Installation

Figure 49. Hose Hanger Installed

Connect Work Port Hoses

1. The control valve kit contains hoses assembled

with quick couplers. Attach supply hoses to

loader feedlines, following the color scheme

shown in Figure 50.

2. Connect loader supply hoses to control valve

hydraulic couplers when attaching loader.

Figure 50. LU126 & LU132 Control Valve and Loader Feedline Hose Connections

11 9

DP5

Hydraulic Installation 27

MAN0041 (Rev. 4/4/2008)

1023583 Hose Kit14

Verification of Control Movements

1. Mount loader to tractor: Remove mount pins

from loader uprights. Align tractor with loader and

lowly drive tractor into loader. Shut off tractor.

2. Connect loader feedline hoses to control valve

hydraulic couplers (See Figure 50).

3. Comply with all Safety Rules and start the tractor.

4. Mount loader to tractor by activating bucket

cylinders to raise or lower the loader uprights into

the loader mounts. Slowly advance tractor

forward, activating appropriate cylinders to

engage loader completely into mounts. Insert

mounting pins to secure loader.

5. Check that all hydraulic control lever positions

operate the loader movements correctly as

shown in Figure 51.

6. If loader movements do not respond correctly,

shut off tractor, relieve pressure, and reconnect

properly. Loader control movements must be

correct before proceeding.

7. Once all loader functions are correct, start the

tractor and operate the loader to check for leaks.

Purge any remaining air from the hydraulic

system.

8. When hose routings and correct loader

operations are verified, identify each circuit by

placing a matching colored band around the male

and female quick-disconnect coupler set. The

colored bands will make re-installation easier

when the loader is remove from the tractor.

9. Be sure the adequate slack is left in the hoses so

they can move as the loader moves through its

full range of motion.

10. Attach plastic tie straps every 20" around the

hoses to keep them tightly bound and away from

contact with the ground or other moving parts on

tractor.

11. Before operating the loader, make sure that the

Pre-Delivery, Delivery, and Pre-Operation

Checklists from the Operation section in the

Loader Operator’s Manual have been completed.

Figure 51. Single Lever Control Operation

●Handle forward - Boom down

●Handle forward to limit - Float position

●Handle back - Boom up

●Handle right - Dump bucket

or attachment (slow)

●Handle right to limit - Dump bucket

or attachment (fast)

●Handle to left - Rollback bucket or attachment

28 Parts

MAN0041 (Rev. 4/4/2008)

111874 LOADER MOUNTING KIT

REF PART QTY DESCRIPTION

1 1000468 1 Right rear mount

2 1000469 1 Left rear mount

3 40448 1 Grill guard kit

(optional; included items 4-6)

4 40449 1 Grill guard

5 307553 8 M20 x 2.5 x 50 mm HHCS

REF PART QTY DESCRIPTION

6 21531 4 M20 Lock washer

7 1001377 2 M20 x 2.5 x 40 mm HHCS CL10.9

8 21413 4 M20 x 2.5 x 70 mm HHCS CL10.9

9 57798 10 3/4 Hardened flat washer

10 1010461 1 Exhaust weather cap 2.25 - 2.43

HHCS Hex Head Cap Screw

* Standard hardware, obtain locally

Parts 29

MAN0041 (Rev. 4/4/2008)

1010460 HOSE KIT

1020, 1027 LOADERS

1023577 HOSE KIT

LU126, LU132 LOADERS

REF PART QTY DESCRIPTION

1 1010920 4 Adapter, M22 x 1.5 x 3/4 JICM

1 1012055 4 Adapter, M18 x 1.5 x 3/4 JICM

2 313015 4 Elbow, 3/8 NPTM x 3/8 NPTF 45°

3 315036 4 Adapter, 3/8 NPTM x 3/4 JICF

4 1009513 4 Hose, 76" x 3/8 NPTM x 3/4 JICM

5 316007 4 Quick coupler set, male & female

NS 395061 2 Spiral band, plastic - Red

NS 395062 2 Spiral band, plastic - Blue

NS 395063 2 Spiral band, plastic - Orange

NS 88 * 3 Plastic tie (TY-RAP)

* Standard hardware, obtain locally

NS Not Shown

REF PART QTY DESCRIPTION

1 1010920 4 Adapter, M22 x 1.5 x 3/4 JICM

1 1012055 4 Adapter, M18 x 1.5 x 3/4 JICM

2 313015 4 Elbow, 3/8 NPTM x 3/8 NPTF 45°

3 315036 4 Adapter, 3/8 NPTM x 3/4 JICF

4 1022986 4 Hose, 116" x 3/8 NPTM x 3/4 JICM

5 316007 4 Quick coupler set, male & female

NS 395061 2 Spiral band, plastic - Red

NS 395062 2 Spiral band, plastic - Blue

NS 395063 2 Spiral band, plastic - Orange

NS 88 * 3 Plastic tie (TY-RAP)

* Standard hardware, obtain locally

NS Not Shown

30 Parts

MAN0041 (Rev. 4/4/2008)

46945 HOSE KIT

1020, 1027 LOADERS

REF PART QTY DESCRIPTION

2 46947 3 Hose, 120” x 3/4 JICF x 7/8 JICF

3 58081 1 Adapter, M22 x 1.5M x 7/8 JICM

4 58647 1 Adapter, M18 x 1.5M x 7/8 JICM

5 315024 2 Elbow, 7/8 JICM x 7/8 JICF

6 46054 1 Elbow, 7/8 JICM x 7/8 JICF 45°

7 54305 1 Hose guide

8 307203 1 M10 x 1.25P x 35 mm HHCS

REF PART QTY DESCRIPTION

9 58280 1 Hose hanger

10 46948 1 Spacer, .62 x .84 x .38

11 58047 1 1/4 x 2-1/2 Lock pin

12 31138 * 1 3/8 NC x 3-1/2 HHCS

13 838 * 1 3/8 Lock washer

14 835 * 1 3/8 NC Hex nut

15 88 * 6 Plastic ties (not shown)

HHCS Hex Head Cap Screw

* Standard hardware, obtain locally

Parts 31

MAN0041 (Rev. 4/4/2008)

1023583 HOSE KIT

LU126, LU132 LOADERS

NOTE: Not all parts supplied with this

hose kit are used for this application.

REF PART QTY DESCRIPTION

1 1002862 2 Hose, 120" x 3/4 JICF x 3/4 JICF 90°

2 1023496 1 Hose, 120" x 3/4 JICF x 7/8 JICF

3 1010920 1 Adapter, M22 x 1.5P x 3/4 JICM

4 44426 1 Adapter, M18 x 1.5P x 3/4 JICM

5 313032 2 Elbow, 3/4 JICM x 3/4 JICF 90°

6 46054 1 Elbow, 7/8 JICFM x 7/8 JICF 45°

9 58280 1 Hose Bracket

10 46948 1 Spacer, .62 x .84 x .38

11 58047 1 Pin, lock 1/4 x 2-1/4

REF PART QTY DESCRIPTION

12 31138 * 1 3/8 NC x 3-1/2 HHCS

13 838 * 1 3/8 Lock washer

14 835 * 1 3/8 NC Hex nut

15 88 * 6 Plastic tie (not shown)

17 60 1 Elbow, 3/4 JICM x 7/8 ORBM

18 346143 1 PBY conversion plug

HHCS Hex Head Cap Screw

* Standard hardware, obtain locally

32 Parts

MAN0041 (Rev. 4/4/2008)

58025 HOSE KIT

1020, 1027 LOADERS

REF PART QTY DESCRIPTION

1 53670 4 Hose, 150” x 3/4 JICM x 3/4 JICM

2 313053 4 Elbow, 3/4 JICF x 1/2 NPTM 90°

3 66511 4 Quick coupler, Male 1/2"

(not included in kit)

6 30577 1 M8 x 1.25P x 25 mm HHCS GR8.8

7 2472 * 1 5/16 Lock washer

8 58033 2 Hose hanger

9 58047 2 1/4 x 2-1/2 Lock pin

REF PART QTY DESCRIPTION

NS 58677 1 Support bracket (not used)

NS 54305 1 Hose guide bracket (not used)

NS 89 * Nylon cable ties

NS 395061 2 Spiral band, red

NS 395062 2 Spiral band, blue

NS 395063 2 Spiral band, orange

NS 54124 2 Spiral band, white

NS Not shown

HHCS Hex Head Cap Screw

* Standard hardware, obtain locally

Parts 33

MAN0041 (Rev. 4/4/2008)

1023584 HOSE KIT

LU126, LU132 LOADERS

REF PART QTY DESCRIPTION

1 1023493 4 Hose, 200" x 3/4 JICM x 3/4 JICM

2 313053 4 Elbow, 3/4 JICF x 1/2 NPTF 90°

3 66511 4 Quick coupler, Male 1/2"

(not included in kit)

4 59520 1 Hose hanger bracket

5 58047 1 1/4 x 2-1/2 Lock pin

NS 395061 2 Plastic band, Red

NS 395062 2 Plastic band, Blue

NS 56061 2 Plastic band, Green

NS 56062 2 Plastic band, Yellow

NS 88 * Plastic tie

NS Not shown

* Standard hardware, obtain locally

NOTE: Not all parts supplied with this

hose kit are used for this application.

34 Appendix

Bolt Torque & Size Charts (Rev. 3/28/2007)

BOLT TORQUE CHART

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific

application.

Fasteners must always be replaced with the same grade as specified in the manual parts list.

Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.

Make sure fastener threads are clean and you start thread engagement properly.

All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.

Diameter

(Inches)

Wrench

Size

MARKING ON HEAD

SAE 2 SAE 5 SAE 8

lbs-ft N-m lbs-ft N-m lbs-ft N-m

1/4" 7/16" 6 8 10 13 14 18

5/16"1/2"121719262737

3/8"9/16"233135474967

7/16"5/8"3648557578106

1/2" 3/4" 55 75 85 115 120 163

9/16" 13/16" 78 106 121 164 171 232

5/8" 15/16" 110 149 170 230 240 325

3/4" 1-1/8" 192 261 297 403 420 569

7/8" 1-5/16" 306 416 474 642 669 907

1" 1-1/2" 467 634 722 979 1020 1383

Diameter &

Thread Pitch

(Millimeters)

Wrench

Size

COARSE THREAD FINE THREAD

Diameter &

Thread Pitch

(Millimeters)

MARKING ON HEAD MARKING ON HEAD

Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9

N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft

6 x 1.0 10 mm 8 6 11 8 8 6 11 8 6 x 1.0

8 x 1.25 13 mm 20 15 27 20 21 16 29 22 8 x 1.0

10 x 1.5 16 mm 39 29 54 40 41 30 57 42 10 x 1.25

12 x 1.75 18 mm 68 50 94 70 75 55 103 76 12 x 1.25

14 x 2.0 21 mm 109 80 151 111 118 87 163 120 14 x 1.5

16 x 2.0 24 mm 169 125 234 173 181 133 250 184 16 x 1.5

18 x 2.5 27 mm 234 172 323 239 263 194 363 268 18 x 1.5

20 x 2.5 30 mm 330 244 457 337 367 270 507 374 20 x 1.5

22 x 2.5 34 mm 451 332 623 460 495 365 684 505 22 x 1.5

24 x 3.0 36 mm 571 421 790 583 623 459 861 635 24 x 2.0

30 x 3.0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2.0

SAE SERIES

TORQUE

CHART

SAE Bolt Head

Identification

SAE Grade 2

(No Dashes)

SAE Grade 5

(3 Radial Dashes)

SAE Grade 8

(6 Radial Dashes)

METRIC SERIES

TORQUE

CHART

Metric Bolt Head

Identification

8.8

Metric

Grade 10.9

10.9

Metric

Grade 8.8

Typical Washer

Installations

Lock Washer

Flat Washer

8/9/00

Bolt

Appendix 35

Bolt Torque & Size Charts (Rev. 3/28/2007)

BOLT SIZE CHART

NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

ABBREVIATIONS

AG .............................................................. Agriculture

ASABE.................... American Society of Agricultural &

Biological Engineers (formerly ASAE)

ASAE ....... American Society of Agricultural Engineers

ATF ............................... Automatic Transmission Fluid

BSPP .............................British Standard Pipe Parallel

BSPTM ................ British Standard Pipe Tapered Male

CV.....................................................Constant Velocity

CCW .............................................. Counter-Clockwise

CW............................................................... Clockwise

F ...................................................................... Female

FT .............................................................. Full Thread

GA .................................................................... Gauge

GR (5, etc.) ........................................... Grade (5, etc.)

HHCS ........................................Hex Head Cap Screw

HT........................................................... Heat-Treated

JIC .................Joint Industry Council 37° Degree Flare

LH .................................................................Left Hand

LT........................................................................... Left

m......................................................................... Meter

mm................................................................Millimeter

M.......................................................................... Male

MPa.........................................................Mega Pascal

N.......................................................................Newton

NC ......................................................National Coarse

NF ...........................................................National Fine

NPSM.....................National Pipe Straight Mechanical

NPT .......................................... National Pipe Tapered

NPT SWF .........National Pipe Tapered Swivel Female

ORBM .......................................... O-Ring Boss - Male

P...........................................................................Pitch

PBY ...................................................... Power-Beyond

psi..........................................Pounds per Square Inch

PTO ..................................................... Power Take Off

QD....................................................Quick Disconnect

RH ..............................................................Right Hand

ROPS ........................... Roll-Over Protective Structure

RPM ........................................Revolutions Per Minute

RT ....................................................................... Right

SAE ..........................Society of Automotive Engineers

UNC .....................................................Unified Coarse

UNF...........................................................Unified Fine

UNS...................................................... Unified Special

5/16 3/81/2 5/83/4 7/8

SAE Bolt Thread Sizes

MM 25 50 75 100 125 150 175

IN 1 7

Metric Bolt Thread Sizes

8MM 18MM14MM12MM10MM 16MM

234 56

F-8494 (Rev. 6/23/2005)

WARRANTY

(Replacement Parts For All Models Except Mow’n MachineTM

Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and

workmanship for a period of ninety (90) days from the date of delivery of the product to the original

purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a

period of 12 months.

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of

WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This

Warranty does not cover normal wear or tear, or normal maintenance items.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell

or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser

in any way. There are no third party beneficiaries of this Warranty.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of

charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with

this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)

days after such defect or noncompliance is discovered or should have been discovered, routed through

the dealer and distributor from whom the purchase was made, transportation charges prepaid.

WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the

product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF

REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS

WA RRA N TY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF

THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND

WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/

OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising

directly or indirectly from the product, whether such claim is based upon breach of contract, breach

of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality

of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or

goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for

labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to

obtain materials or manufacture replacement parts.

No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,

including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized

to alter, modify, or enlarge this Warranty.

Answers to any questions regarding warranty service and locations may be obtained by contacting:

F-3079 (Rev. 4/4/2008)

WARRANTY

(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)

Please Enter Information Below and Save for Future Reference.

Date Purchased: ____________________________ From (Dealer): ___________________________________________

Model Number: ____________________________ Serial Number: ___________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set

forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE

PRODUCT TO THE ORIGINAL PURCHASER.

Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.

The warranty periods for specific parts or conditions are listed below:

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to

improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been

materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized

service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made

with parts other than those obtainable through WOODS.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to

a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.

WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by

WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,

in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof

of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the

dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or

replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS

WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS

WARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS

MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY

OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the

product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal

theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,

revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute

machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture

replacement parts.

No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,

its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.

Answers to any questions regarding warranty service and locations may be obtained by contacting:

Part or

Condition

Warranted

Model Number Duration (from date of delivery

to the original purchaser)

Gearbox

components

BW1260, BW1800 8 years

BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X,

BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-2, BW180-2 6 years

PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,

RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,

9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD

5 years

RDC54, RD60, RD72 3 years (1 year if used in rental or

commercial applications)

Blade spindles RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,

9180RD-2, 9204RD-2 3 years

Rust-through BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-2, BW180-2,

BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680 10 years

PART NO.

MAN0041

Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual

are the property of their respective companies or mark holders. Specifications subject to change without notice.

Woods Equipment

Company

2606 South Illinois Route 2

Post Office Box 1000

Oregon, Illinois 61061

800-319-6637 tel

800-399-6637 fax

www.WoodsEquipment.com

Woods Equipment Lu126 Users Manual 111874 Loader Mounting Kit (LU126, LU132, 1020, 1027)

LU126 to the manual 6c5de27d-e6d9-4668-a024-f65e0a059ce4

Navigation menu

Versions of this User Manual:

Views

Navigation