Woods Equipment Rd60 Users Manual Heritage Rear Discharge Mower RDC54, And RD72

!! Woods-45 Woods Equipment Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

RD60 to the manual cb3a9fcc-3692-4928-be9e-921791297a6a

2015-02-05

: Woods-Equipment Woods-Equipment-Rd60-Users-Manual-408590 woods-equipment-rd60-users-manual-408590 woods-equipment pdf

Open the PDF directly: View PDF .
Page Count: 48

Download
Open PDF In Browser	View PDF

Rev. 1/12/2007

MAN0260

RDC54
RD60
RD72

Tested. Proven. Unbeatable.

OPERATOR'S MANUAL

HERITAGE
REAR DISCHARGE
MOWER

TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual
are completed before releasing equipment to the owner.
The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the
registration which certifies that all Dealer Check List items have been completed. The dealer is to return the prepaid
postage portion to Woods, give one copy to the customer, and retain one copy. Failure to complete and return this
card does not diminish customer’s warranty rights.
TO THE OWNER:
Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and
safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become
acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be
obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in
the United States and Canada call 1-800-319-6637.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces
provided:

Model: _______________________________

Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term IMPORTANT is used to indicate that failure to observe can cause damage to
equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a
triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety.
This Safety-Alert Symbol indicates a hazard and means ATTENTION!
BECOME ALERT! YOUR SAFETY IS INVOLVED!

DANGER

Indicates an imminently hazardous situation that, if not avoided, will
result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if not avoided, could
result in death or serious injury, and includes hazards that are exposed
when guards are removed.

CAUTION
IMPORTANT
NOTE

Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury.
Indicates that failure to observe can cause damage to equipment.
Indicates helpful information.

2 Introduction

Gen’l (Rev. 6/6/2005)

TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DEALER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 44
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER

LEA EL INSTRUCTIVO!

Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.

MAN0260 (Rev. 1/12/2007)

Introduction 3

SPECIFICATIONS
MODEL

RDC54

RD60

RD72

3-Point Hitch

Limited Cat. 1

Cat. 1

Cutting Width

54"

60"

72"

Cutting Height Range

1" - 4-1/2"

Operating Weight with
Chain Shielding

417 lbs.

521 lbs.

624 lbs.

Blade Speed (feet per minute)

16,200

18,000

18,100

Blade Spindles

Number of Blades

Universal Drive Series

ASAE Cat. 3

Caster Wheels

3.5 x 4 x 10

Tractor PTO Speed RPM

540

Recommended Maximum
Tractor Horsepower

15-25

25-35

Mower Frame Thickness

10 GA

8 GA

GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your mower. Read it carefully. It furnishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature, due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.

The illustrations and data used in this manual were current at the time of printing. However, due to possible
inline production changes, your machine may vary
slightly in detail. We reserve the right to redesign and
change the machines as may be necessary without
notification.
Throughout this manual, references are made to right
and left directions. These are determined by standing
behind the tractor facing the direction of forward travel.

WARNING
■

Some illustrations in this manual show the
mower with safety shields removed to provide a
better view. The mower should never be operated
with any safety shielding removed.

4 Introduction

MAN0260 (Rev. 1/12/2007)

SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident prevention are dependent upon the awareness, concern,
judgement, and proper training of personnel
involved in the operation, transport, maintenance
and storage of equipment.
It has been said “The best safety device is an
informed, careful operator.” We ask you to be that
kind of operator.

TRAINING
Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
Know your controls and how to stop engine and
attachment quickly in an emergency.
If you do not understand any part of this manual
and need assistance, see your dealer.
Operators must be instructed in and be capable
of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
Never allow children or untrained persons to
operate equipment.

PREPARATION
Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
Always wear relatively tight and belted clothing
to avoid entanglement in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
Make sure attachment is properly secured,
adjusted, and in good operating condition.

RD 54/60/72 (Rev. 1/12/2007)

Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
Make sure driveline shield tether chains are
attached to the tractor and equipment as shown in
this manual. Replace if damaged or broken. Check
that driveline guards rotate freely on driveline
before putting equipment into service.
Before starting power unit, check all equipment
driveline guards for damage. Replace any damaged
guards. Make sure all guards rotate freely on all
drivelines. If guards do not rotate freely on drivelines, repair and replace bearings before putting
equipment into service.
Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS systems in “locked up” position at all times.
Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS systems in “locked up” position at all times.
Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard.
Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
A minimum 25% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a
loader. Weigh the tractor and equipment. Do not
estimate.

OPERATION
Full chain shielding, designed to reduce the
possibility of thrown objects, must be installed
when operating in populated areas or other areas
where thrown objects could injure people or damage property. If this machine is not equipped with
full chain shielding, operation must be stopped
when anyone comes within several hundred feet.

Safety 5

SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
Never direct discharge toward people, animals,
or property.
Keep bystanders away from equipment.
Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body underneath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.

TRANSPORTATION
Use additional caution and reduce speed when
under adverse surface conditions, turning, or on
inclines.
Do not operate PTO during transport.
A minimum 25% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a
loader. Weigh the tractor and equipment. Do not
estimate.
Do not operate or transport on steep slopes.
Do not operate or transport equipment while
under the influence of alcohol or drugs.
Always comply with all state and local lighting
and marking requirements.

Do not operate or transport equipment while
under the influence of alcohol or drugs.

Never allow riders on power unit or attachment.

Operate only in daylight or good artificial light.

MAINTENANCE

Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.

Before working underneath, carefully read Operator’s Manual instructions, disconnect driveline,
raise mower, securely block up all corners with
jackstands, and check stability. Secure blocking
prevents equipment from dropping due to hydraulic leak dow n, hydraulic system failures, or
mechanical component failures.

Always comply with all state and local lighting
and marking requirements.
Never allow riders on power unit or attachment.
Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
Operate tractor PTO at 540 RPM. Do not exceed.
Look down and to the rear and make sure area
is clear before operating in reverse.
Do not operate or transport on steep slopes.
Do not stop, start, or change directions suddenly on slopes.
Use extreme care and reduce ground speed on
slopes and rough terrain.
Watch for hidden hazards on the terrain during
operation.
Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,
using proper procedure. Inspect and repair any
damage before resuming operation.

6 Safety

Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its components in any way.
Always wear relatively tight and belted clothing
to avoid entanglement in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
Make sure attachment is properly secured,
adjusted, and in good operating condition.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
Make certain all movement of equipment components has stopped before approaching for service.
Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body underneath equipment or between moveable parts even

RD 54/60/72 (Rev. 1/12/2007)

SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.
Frequently check blades. They should be sharp,
free of nicks and cracks, and securely fastened.
Do not handle blades with bare hands. Careless
or improper handling may result in serious injury.
Your dealer can supply genuine replacement
blades. Substitute blades may not meet original
equipment specifications and may be dangerous.
Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.

Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
Wear gloves when installing belt. Be careful to
prevent fingers from being caught between belt
and pulley.
Use care when installing or removing belt from
spring-loaded idler. Springs store energy when
extended and, if released suddenly, can cause personal injury.

STORAGE
Follow manual instructions for storage.
Keep children and bystanders away from storage area.

RD 54/60/72 (Rev. 1/12/2007)

Safety 7

SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!

2 - 18867

DANGER
SHIELD MISSING
DO NOT OPERATE
PUT SHIELD ON
18867--B

3 - Serial Number Plate
11 - 20106 - Rear Reflector (RD60 & RD72 Only)
MODEL NO.

SERIAL NO.

Woods Equipment Company
Oregon, Illinois, U.S.A.

1 - 15503

DANGER

4 - 1003751

WARNING
CRUSHING AND PINCHING HAZARD

ROTATING BLADES AND
THROWN OBJECTS

Be extremely careful handling various parts of

Do not put hands or feet under or into mower when

engine is running.

Before mowing, clear area of objects that may be

thrown by blade.

Keep bystanders away.
Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN
CAUSE SERIOUS INJURY OR DEATH.
15503-C

8 Safety

the machine. They are heavy and hands, fingers,
feet, and other body parts could be crushed or
pinched between tractor and implement.
Operate tractor controls from tractor seat only.
Do not stand between tractor and implement
when tractor is in gear.
Make sure parking brake is engaged before
going between tractor and implement.
Stand clear of machine while in operation or
when it is being raised or lowered.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
1003751-A

MAN0260 (Rev. 1/12/2007)

SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
5 - 18866

WARNING

8 - 18865

DO NOT EXCEED PTO SPEED OF

540 RPM
PTO speeds higher than 540 RPM can cause
equipment failure and personal injury.

FALLING OFF CAN RESULT IN BEING RUN OVER.
Tractor must be equipped with ROPS (or ROPS CAB) and seat

18866-D

belt. Keep foldable ROPS systems in “locked up” position at all
times.
Buckle Up! Keep seat belt securely fastened.

DANGER

Allow no riders.

6 - 18864

RAISED EQUIPMENT CAN DROP AND CRUSH.
Before working underneath, follow all instructions and safety rules in

operator’s manual and securely block up all corners of equipment
with jack stands.
Securely blocking prevents equipment dropping from hydraulic leak-

down, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN
RESULT IN SERIOUS INJURY OR DEATH.
18865--C

ROTATING DRIVELINE
CONTACT CAN CAUSE DEATH

KEEP AWAY!
DO NOT OPERATE WITHOUT -

DANG
NGER
ER

All driveline guards, tractor and
equipment shields in place
Drivelines securely attached at both ends
Driveline guards that turn freely on
driveline

9 - 1004114

If shaft connection is visible, shield
is missing. Replace shield before
operating equipment.
1004114

18864-C

10 - 33347

DANGER

BE CAREFUL!
7 - 1002423

WARNING
TO AVOID SERIOUS INJURY OR DEATH:
Read Operator's Manual before operating,
servicing or repairing equipment. Follow all
safety rules and instructions. (Manuals are
available from your selling dealer.)
Never allow riders.
Keep bystanders away from equipment during
operation.
Operate from tractor seat only.
Keep all shields in place and in good condition.
Lower equipment to ground, stop engine,
remove key and set brake before dismounting
tractor.
Never allow children or untrained persons to
operate equipment.
Do not transport towed or semi-mounted units
over 20 MPH.
FAILURE TO FOLLOW THESE INSTRUCTIONS
1002423-B
CAN RESULT IN INJURY OR DEATH.

MAN0260 (Rev. 1/12/2007)

Use a clean, damp cloth to
clean safety decals. Avoid
spraying too close to decals
when using a pressure
washer; high-pressure water
can enter through very small
scratches or under edges of
decals causing them to peel
or come off.
Replacement safety decals
can be ordered free from your
Woods dealer. To locate your
nearest dealer, check the
Dealer
Locator
at
www.WoodsEquipment.com,
or in the United States and
Canada call 1-800-319-6637.

GUARD MISSING.
DO NOT OPERATE.

DANGER
GUARD MISSING.
DO NOT OPERATE.

33347E

DANGER
Safety 9

OPERATION
The operator is responsible for the safe operation of
the mower. The operator must be properly trained.
Operators should be familiar with the mower, the tractor, and all safety practices before starting operation.
Read the safety rules and safety decals on page 5
through page 9.
This mower is designed for lawn and grass mowing. It
is not designed for rough conditions or heavy weed
mowing. It is equipped with suction type blades for best
results in lawn mowing.
Recommended mowing speed for most conditions is
from 2 to 5 mph.

using proper procedure. Inspect and repair any
damage before resuming operation.
Always wear relatively tight and belted clothing
to avoid entanglement in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.

Tractor Stability

WARNING
A minimum 25% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a
loader. Weigh the tractor and equipment. Do not
estimate.

WARNING
Never allow children or untrained persons to
operate equipment.
Keep bystanders away from equipment.
Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
Operate tractor PTO at 540 RPM. Do not exceed.
Before working underneath, carefully read Operator’s Manual instructions, disconnect driveline,
raise mower, securely block up all corners with
jackstands, and check stability. Secure blocking
prevents equipment from dropping due to hydraulic leak down, hydraulic system failures, or
mechanical component failures.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.

CAUTION
Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,

10 Operation

Figure 1. Tractor Stability

Attach Mower to Tractor

WARNING
Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
The standard 1-3/8" 6B-spline driveline with a QD yoke
is used to connect the mower to the tractor.
1. Attach the mower hitch pins to the lower tractor lift
arms and secure.
2. Attach tractor top link (1), Figure 2, to mower top
link bracket attachment point (A). Connect the
driveline to the tractor PTO shaft.
3. Attach tether chain to tractor drawbar (Figure 3).
4. Adjust the tractor lower 3-point arm anti-sway
devices to prevent mower from swinging side to
side during transport.

MAN0260 (Rev. 1/12/2007)

4. To raise rear of mower, move caster adjustment
spacers under rear caster arms.
5. To raise front of mower, move spacers under front
caster wheel arms.
Table 1: Cutting Height Chart
Spacers Required Under
Caster Arm Pivot Tube
1. Tractor Top Link
A. Mower Top Link Attachment Point
B. Mower Hitch Pin
Figure 2. Attachment Points

Cut Height

1/2" Spacer

1" Spacer

1-1/2"

2-1/2"

3-1/2"

4-1/2"

Tether Chain

Tractor Top Link Adjustment

CM906

Figure 3. Attach Mower to Tractor

Adjust Cutting Height

WARNING
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.

When the cutting height is set, adjust tractor top link
until mower top link attachment point (A), Figure 4, is
aligned vertically with mower hitch pin (B). The front
tires of the mower will lift off the ground before the rear
tires when the unit is raised. This will allow the mower
to follow the ground contour.
A. Mower top link attachment point
B. Mower hitch pin
C. Tractor top link
D. Mower hitch plate attachment point

IMPORTANT
■

Avoid low cutting heights. Striking the ground
with blades produces one of the most damaging
shock loads a mower can encounter. Allowing
blades to contact ground repeatedly will cause
damage to mower and drive.
1. Level mower from side to side. Check by
measuring distance from mower frame to the
ground at each deck rail.

Figure 4. Top Link Adjustment

2. Verify that the same amount of spacers are under
all caster arms.

RDC54 Only

3. Control cutting height by adjusting front and rear
caster wheels.

The RDC54 has two mower hitch plate attachment
points (D). It may be necessary to change the mower

MAN0260 (Rev. 1/12/2007)

Operation 11

hitch plate attachment point to obtain proper tire clearance and/or lift height.

Front Caster Wheel Interference Check

IMPORTANT
■

Do not operate tractor and mower until this
interference check has been performed. If you
change tractors, you must perform the check for
that mounting.
Perform this check with all of the spacers and springs
above the caster wheel arm. This will place the caster
wheels in their highest position and provide the lowest
cutting height for the mower.
1. Raise mower with tractor hydraulics to 16" at
dimension C, Figure 5, or maximum height of
tractor lift, whichever is less.
2. Pivot both front caster wheels forward and check
that there is clearance between caster wheels and
tractor tires.
3. If there is interference on RDC54 model, adjust
mower hitch plate point as shown in Figure 4. On
model RD60 and RD72, the hitch plate is not
adjustable; see tractor operator’s manual and
adjust tractor wheels accordingly.

CAUTION
Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,
using proper procedure. Inspect and repair any
damage before resuming operation.
Power for operating the mower is supplied by the tractor PTO. Operate PTO at 540 rpm. Know how to stop
tractor and mower quickly in an emergency.
If mower becomes plugged causing belt to slip for over
two seconds, follow these steps:
1. Maneuver equipment into a previously cut area
and allow mower to clear accumulated material.
2. Continue running at least two minutes, allowing
pulleys to cool. Stopping the mower when in
contact with a very hot pulley will bake and ruin
belt.
Proper ground speed will depend upon the terrain, the
height, and type and density of material to be cut.
Normally, ground speed will range from 2 to 5 mph. Tall
dense material should be cut at a low speed; thin
medium-height material can be cut at a faster ground
speed. Always operate tractor PTO at 540 rpm to maintain proper blade speed and produce a clean cut.
Under certain conditions, tractor tires may roll some
grass down and prevent it from being cut at the same
height as the surrounding area. When this occurs,
reduce your ground speed, but maintain PTO at 540
rpm. The lower ground speed will permit grass to partially rebound.
In general, lower cutting heights give a more even cut
and leave less tire tracks. However, it is better to cut
grass frequently rather than too short. Short grass
deteriorates rapidly in hot weather and invites weed
growth during growing seasons. Follow local recommendations for the suitable cutting height in your area.

Figure 5. Front Caster Wheel Interference Check

Front Roller (Optional)
The caster wheels effectively reduce scalping in most
cases. However, you may encounter areas where the
caster wheels and/or side skids drop into depressions
and allow center of the mower to contact ground and
scalp. An optional front roller may be installed to minimize scalping. See page 40.

Operating Technique

Operating Tips

WARNING
Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
Extremely tall material should be cut twice. Set mower
at a higher cutting height for the first pass. Then cut at
desired height, 90 degrees to the first pass. Remember, sharp blades produce cleaner cuts and require
less power.
Analyze area to be cut to determine the best procedure. Consider height and type of grass and terrain

12 Operation

MAN0260 (Rev. 1/12/2007)

type: hilly, level, or rough. Plan your mowing pattern to
travel straight forward whenever possible. Mow with
uncut grass to the right. This will distribute the clippings
over the cut area.

Uneven Terrain

WARNING

OWNER PRE-OPERATION CHECK LIST
(OWNER'S RESPONSIBILITY)
___ Review and follow all safety rules and safety
decal instructions on page 5 through page 9.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.

Do not operate or transport on steep slopes.

___ Check that all shields and guards are properly
installed and in good condition. Replace if damaged.

Do not stop, start, or change directions suddenly on slopes.

___ Check that chain shielding is in good condition
and replace any damaged chain links.

Use extreme care and reduce ground speed on
slopes and rough terrain.

___ Check that all hardware and cotter pins are properly installed and secured.

Watch for hidden hazards on the terrain during
operation.

___ Check to ensure blades are sharp, in good condition, and installed correctly. Replace if damaged.

Pass diagonally through sharp dips and avoid sharp
drops to prevent hanging up tractor and mower. Practice will improve your skills in maneuvering rough terrain.

___ Check that equipment is properly and securely
attached to tractor.

Removing Mower from Tractor - Storage
Follow cleaning procedure, page 17.
1. Disengage tractor PTO and raise mower with the
3-point hitch.
2. Disconnect mower driveshaft from tractor PTO.
3. Collapse driveshaft as far as possible and store it
in PTO hanger bracket to prevent ground contact.
4. Place blocks under mower side skids. Lower
mower onto blocks, disconnect mower from tractor
3-point hitch, and carefully drive tractor away from
mower.

WARNING
Keep children and bystanders away from storage area.

___ Make sure driveline spring-activated locking pin
or collar slides freely and is seated firmly in tractor PTO spline groove.
___ Make sure the driveline guards and tether chains
are in good condition. Guards must rotate freely
on driveline. Fasten tether chains to the tractor
and the equipment as instructed.
___ Inspect area and remove stones, branches or
other hard objects that might be thrown, causing
injury or damage.
___ Do not allow riders.
___ Check all lubrication points and grease as
instructed in “Lubrication Information” on page 14
& page 15. Make sure the PTO slip joint is lubricated and that the gearbox fluid levels are correct.
___ Set tractor PTO at correct rpm for your equipment.
___ Make sure tractor ROPS or ROPS cab and seat
belt are in good condition. Keep seat belt
securely fastened during operation.
___ Before starting engine, operator must be in tractor seat with seat belt fastened. Place transmission in neutral or park, engage brake, and
disengage tractor PTO.

Figure 6. Mower Storage Position

MAN0260 (Rev. 1/12/2007)

Operation 13

OWNER SERVICE
The information in this section is written for operators
who possess basic mechanical skills. If you need help,
your dealer has trained service technicians available.
For your protection, read and follow the safety information in this manual.

solid to support the loaded weight of the jackstands.
Test jackstand stability before working under any portion of the mower.

CAUTION
Always wear relatively tight and belted clothing
to avoid entanglement in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.

WARNING
Never allow children or untrained persons to
operate equipment.
Keep bystanders away from equipment.
Before working underneath, carefully read Operator’s Manual instructions, disconnect driveline,
raise mower, securely block up all corners with
jackstands, and check stability. Secure blocking
prevents equipment from dropping due to hydraulic leak down, hydraulic system failures, or
mechanical component failures.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
Operate tractor PTO at 540 RPM. Do not exceed.

BLOCKING METHOD
Do not work underneath mower unless it is properly
attached to the tractor and blocked securely. When
properly attached, the unit will be anchored to minimize
front to rear movement.
Raise mower completely, set tractor brakes, turn
engine off, remove key, block tractor wheels front and
rear, and disconnect mower driveline from tractor.
The only approved blocking devices for this mower are
jackstands with a load rating of 1000 pounds or more.
One jackstand under each corner of the mower (four
total) must be installed before working underneath this
unit.
When blocking, you must consider overall stability of
the unit. Just blocking under the unit will not ensure
your safety. The working surface must be level and

14 Owner Service

Figure 7. Jackstand Placement

Lubrication Information
Do not let excess grease collect on or around parts,
particularly when operating in sandy areas.
Figure 8 shows the lubrication points. The accompanying chart gives the frequency of lubrication in operating
hours, based on normal operating conditions.
Severe or unusual conditions may require more frequent lubrication. Some reference numbers have more
than one location; be sure you lubricate all locations.
Use a lithium grease of #2 consistency with a MOLY
(molybdenum disulfide) additive for all locations. Be
sure to clean fittings thoroughly before attaching
grease gun. When applied according to the lubrication
chart, one good pump of most guns is sufficient.
Use SAE 90W gear lube in the gearbox. Fill to plug on
side of gearbox.
Check gearbox daily for evidence of leakage at both
seals and the gasket between the housing and cover. If
leakage is noted, repair immediately. There may be a
small amount of lube emitted from the vent plug; this is
not considered leakage.
Overfilling the gearbox will cause the excess gear lube
to blow out vent plug and ruin the belt.

Driveshaft Lubrication
Lubricate the driveshaft slip joint every 40 operating
hours. Failure to maintain proper lubrication could
result in damage to U-joints, gearbox, and driveshaft.
1. Lower mower to ground.

MAN0260 (Rev. 1/12/2007)

2. Remove front half of driveshaft.

SERVICE BELT

3. Apply grease all around and along inner shaft.

Replace Belt

4. Reassemble driveshaft halves.

One of the major causes of belt failure is improper
installation. Before installing a new belt, check the following:

5. Raise and lower mower several times to distribute
grease.

1. Check pulley shafts and bearings for wear.
2. Check pulley grooves for cleanliness.
3. Make sure spindles turn freely and without wobble.

Ref
No.

Description

Frequency

Front U-Joint

8 Hours

Caster Wheel (Four wheels)

8 Hours

Caster Pivot (Four wheels)

8 Hours

Left Spindle (Access through hole)

40 Hours

Shield Bearings

8 Hours

Rear U-Joint

8 Hours

Gearbox (Fill to center of horizontal shaft with
SAE 80W or 90W gear lube)

Check Daily
For Leakage

Right Spindle (Access through hole)

40 Hours

Center Spindle (Access through hole)

40 Hours

Slip Joint

40 Hours
Figure 8. Lubrication Points & Chart

MAN0260 (Rev. 1/12/2007)

Owner Service 15

If grooves require cleaning, moisten a cloth with a nonflammable, non-toxic degreasing agent or commercial
detergent and water.
Avoid excessive force during installation. Do not use
tools to pry belt into pulley groove. Do not roll belt over
pulleys to install. This can cause hidden damage and
premature belt failure.

Install Belt
Refer to Figure 9.
1. Slide belt under drive pulley A and over idler arm.
Position belt around drive pulley A.
2. It may be necessary to remove front bolts (1) and
swing gearbox stand up to gain access to pulley A.
Route belt around pulley B, idler C, and pulley D as
shown.
3. Make sure belt is on drive pulley A and route
around idler F.
4. Grasp belt between spindle pulley E, spring-loaded
idler F and spindle pulley D. Pull spring-loaded
idler with belt to obtain enough belt length to route
it over pulley E. Make sure spring-loaded idler
pivots freely with belt installed.

IMPORTANT

SERVICE BLADE

WARNING
Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key,
and unfasten seat belt.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.

CAUTION
Frequently check blades. They should be sharp,
free of nicks and cracks, and securely fastened.
1. Inspect blades before each use to determine that
they are mounted securely and are in good condition.
2. Replace any blade that is bent, excessively nicked,
worn, or has any other damage.
3. Small nicks can be ground out when sharpening.

■

Use care when installing or removing belt from
spring-loaded idler. Springs store energy when
extended and, if released suddenly, can cause personal injury.

Remove Blades

WARNING
Do not handle blades with bare hands. Careless
or improper handling may result in serious injury.
1. Remove bolt (1), Figure 11, which has right hand
threads.
2. Remove washer and blade.

Sharpen Blades

IMPORTANT
■ When sharpening blades, be sure to balance
them. Unbalanced blades will cause excessive
vibration that can damage blade spindle bearings.
Vibration may also cause structural cracks in
mower housings.

Figure 9. Belt Routing

16 Owner Service

MAN0260 (Rev. 1/12/2007)

Chain Shielding

DANGER

Figure 10. Blade Balancing
1. Follow original sharpening pattern.
2. Do not sharpen blade to a razor edge, but leave
approximately 1/64" blunt edge.
3. Do not sharpen back side of blade.
4. Sharpen both cutting edges equally to keep blade
balanced. Balance blade using the method shown
in Figure 10.

Full chain shielding, designed to reduce the
possibility of thrown objects, must be installed
when operating in populated areas or other areas
where thrown objects could injure people or damage property. If this machine is not equipped with
full chain shielding, operation must be stopped
when anyone comes within several hundred feet.
Check that chain shielding is in good condition and
replace any damaged chain links.

CLEANING
After Each Use
●
●

Install Blades

●

CAUTION
Your dealer can supply genuine replacement
blades. Substitute blades may not meet original
equipment specifications and may be dangerous.

IMPORTANT

Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
Inspect machine and replace worn or damaged
parts.
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).

Periodically or Before Extended Storage
●
●

■ When installing blade, the lift of the blade must
be toward the spindle blade housing as shown in
Figure 11. Torque bolt (1) into shaft assembly to
100 lbs-ft.

1. Place blade over blade pilot on the bottom of the
shaft assembly.
2. Place bell washer (2) over blade and insert blade
bolt (1). Torque blade bolt to 100 lbs-ft.
●
●

●

Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
Remove the remainder using a low-pressure water
spray.
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.
Inspect machine and replace worn or damaged
parts.
Sand down scratches and the edges of areas of
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods
dealer).
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).
See Safety Decals section for location drawing.

1. 5/8 NF x 2 Cap screw GR5
2. Bell washer, 5/8 x 1-3/4 x .075
Figure 11. Blade and Spindle Assembly

MAN0260 (Rev. 1/12/2007)

Owner Service 17

TROUBLESHOOTING
MOWING CONDITIONS
PROBLEM
Grass cut higher in center of
swath than at edge

Grass cut lower in center of
swath than at edge

Streaking conditions in swath

Material discharges from mower
unevenly; bunches of material
along swath

POSSIBLE CAUSE

SOLUTION

Height of mower higher at front
than at rear

Adjust mower height and attitude so
that mower rear and front are within
1/2 inch of same height. See instructions on page 11.

Loose blade

Check blade hardware.

Height of mower lower at front
than at rear

Adjust mower height and attitude so
that mower rear and front are within
1/2 inch of same height. See instructions on page 11.

Loose blade

Check blade hardware.

Conditions too wet for mowing

Allow grass to dry before mowing.

Blades unable to cut that part of
grass pressed down by path of
tractor tires

Slow ground speed of tractor but keep
engine running at full PTO rpm. Cutting lower will help. Adjust tractor tire
spacing if possible.

Dull blades

Sharpen or replace blades.

Loose blade

Check blade hardware.

Material too high and too much
material

Reduce ground speed but maintain
540 rpm at tractor PTO, or make two
passes over material. Raise mower
for the first pass and lower for the second and cut 90-degrees to first pass.
Raise rear of mower high enough to
permit material discharge, but not so
high that conditions listed above
occur.

Grass is wet

Allow grass to dry before mowing.
Slow ground speed of tractor but keep
engine running at full PTO rpm.

18 Owner Service

MAN0260 (Rev. 1/12/2007)

TROUBLE SHOOTING
BELT CONDITIONS
PROBLEM
Belt slippage

POSSIBLE CAUSE

SOLUTION

Mower overloading; material too
tall or heavy

Reduce tractor ground speed but
maintain full PTO rpm. Cut material
twice, one high pass and then mow at
desired height. Cut 90-degrees to first
pass.

Oil on belt from over lubricating

Be careful not to over lubricate. Clean
lubricant from belt and pulleys with
clean rag. Replace oil-soaked belt.

Belt hung up or rubbing

Check belt position in pulleys and
idlers. Check belt for free travel in pulleys. Check under mower and around
blade spindle shaft for wire, rags, or
other foreign material. Clean all material from under mower.

Belt is misaligned

Re-align belt. Be sure belt does not
rub any other part while running.

Pulley is misaligned

Inspect to ensure belt is running in
center of backside idler. Shim idler as
necessary to align.

Pulley is misaligned

Re-align.

Damaged belt

Replace belt. *

Foreign object in pulley groove

Inspect all pulley grooves for rust,
paint, or weld spots and remove.

Worn pulley groove

Replace pulley.

Damaged belt

Rollover, high shock loads or
installation damaged

Replace belt. *

Belt breakage

High shock loads

Avoid abusive mowing. Avoid hitting
the ground or large obstructions.

Belt came off drive

Check pulleys for foreign material in
grooves. Avoid hitting solid objects or
ground.

Frayed edges on belt cover

Belt rollover

* Check belt for damage by laying it flat on the floor. A belt that does not lie flat (has humps or twists, indicating broken
or stretched cords) must be replaced.

MAN0260 (Rev. 1/12/2007)

Owner Service 19

DEALER SERVICE
The information in this section is written for dealer service personnel. The repair described here requires
special skills and tools. If your shop is not properly
equipped or your mechanics are not properly trained in
this type of repair, you may be time and money ahead
to replace complete assemblies.

WARNING
Before working underneath, read manual
instructions, securely block up, and check stability.
Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system
failure, or mechanical component failure.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.

CAUTION

Figure 12. Jackstand Placement

BLADE SPINDLE REPAIR
Spindle repair requires special skills and tools. If your
shop is not properly equipped or your mechanics are
not trained in this type of repair, you may be time and
money ahead to use a new spindle assembly.

Always wear relatively tight and belted clothing
to avoid entanglement in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.

For reference, the grease fitting is in the top of the spindle shaft.

BLOCKING METHOD

Remove Spindle

Do not work underneath mower unless it is properly
attached to the tractor and blocked securely. When
properly attached, the unit will be anchored to minimize
front to rear movement.

1.
2.
3.
4.

Raise mower completely, set tractor brakes, turn
engine off, remove key, block tractor wheels front and
rear, and disconnect mower driveline from tractor.

Disassemble Spindle

The only approved blocking devices for this mower are
jackstands with a load rating of 1000 pounds or more.
One jackstand under each corner of the mower (four
total) must be installed before working underneath this
unit.
When blocking, you must consider overall stability of
the unit. Just blocking under the unit will not ensure
your safety. The working surface must be level and
solid to support the loaded weight of the jackstands.
Test jackstand stability before working under any portion of the mower.

20 Dealer Service

Permatex® 3D Aviation Form-A-Gasket or equivalent is
recommended as a sealant.

Remove belt shields from deck.
Remove belt.
Remove blade from spindle assembly.
Remove nuts (6) and bolts (9) that secure spindle
to mower. (See Figure 13.)

1. Remove bolt (1) and washer (2) from the top of the
spindle.
2. Remove sheave (3) and spacer (4).
NOTE: A wheel puller may be needed if sheave
can not be removed by hand. Retain key (11).
3. Slide shaft assembly (12), lower bearing (5), and
long spacer (10) out the bottom of spindle housing
(8).
4. Remove upper bearing (5) and spacer (4) from top
of spindle housing.
5. Inspect parts and replace as needed.

MAN0260 (8/6/2004)

4. Install upper bearing (5) over shaft with the seal
facing up.
5. Install spacer (4) and sheave (3) over shaft.
6. Align keyways in shaft and sheave and insert key
(11).
7. Install washer (2), and bolt (1). Torque bolt to 35
lbs-ft.
8. Rotate sheave and check for free movement.
9. Lubricate spindle.

GEARBOX REPAIR
Read this entire section before starting any repair.
Many steps are dependent on each other.
Fill gearbox with SAE 80W or 90W gear lube until it
runs out the side level plug.
Repair to this gearbox is limited to replacing bearings,
seals, and gaskets. Replacing gears, shafts, and a
housing is not cost effective. It is more economical to
purchase a complete gearbox if repair to anything other
than replacement of bearings, seals or gaskets is
required.
Inspect gearbox for leakage and bad bearings.
Leakage is a very serious problem and must be corrected immediately.
Bearing failure is indicated by excessive noise and side
to side or end play in gear shafts.
CD6308

Seal Replacement
Recommended sealant for gearbox repair is Permatex® Aviation 3D Form-A-Gasket or equivalent.

1. 3/8 NF x 1 HHCS GR5
2. Cup washer
3. Sheave
4. Spacer
5. Spindle bearing
6. 3/8 NC Flange lock nut
7. 1/4 Tapered grease fitting

9. 3/8 NC x 1-1/2 HHCS
GR5

Leakage can occur at the vertical or horizontal gaskets
and shaft seals.

10. Spacer

Leakage at the horizontal gasket or seal can be
repaired without removing the gearbox from the mower.

11. Square key

Seal Installation

12. Shaft assembly

NOTE: Proper seal installation is important. An improperly installed seal will leak.

13. Blade kit
14. Cup washer
15. 5/8 NF x 2 HHCS GR5

8. Spindle housing

Figure 13. Blade Spindle Assembly

1. Clean area in housing where seal outer diameter
(OD) seats. Apply a thin coat of Permatex.
2. Inspect area of shaft where seal seats. Remove
any burrs or nicks with an emery cloth.
3. Lubricate gear shaft and seal lips.

Assemble Spindle
1. Slide lower bearing (5) over shaft assembly (12)
with seal down.
2. Slide long spacer (10) on shaft assembly.
3. Insert shaft assembly with bearing and spacer into
spindle housing from the bottom.

(Rev. 5/27/2005)
MAN0260 (8/6/2004)

4. Place seal squarely on housing, spring-loaded lip
toward housing. Select a piece of pipe or tubing
with an OD that will sit on the outside edge of the
seal but will clear the housing. Tubing with an OD
that is too small will bow seal cage and ruin seal.
5. Carefully press seal into housing,
distortion to the metal seal cage.

avoiding

Dealer Service 21

2
Incorrect
Installation

3
1

CD1092

1.Seal
2.Pipe or tube
3.Seal seat
4.Casting

CD1094

CD6306

Pipe or tube must
press at outer
edge of seal
Figure 14. Seal Installation

Figure 15. Gearbox Stand Assembly

1. Seal
2. Snap ring
3. Shim 55.4 mm x 61.7 mm
4. Ball bearing
5. Input shaft
6. Key 8 mm x 10 mm x 30
mm
7. Input gear
8. Ball bearing
9. Shim 60.3 mm x 71.7 mm
10. Snap ring
11. Oil cap
12. Output shaft & gear

22. Washer 25 mm x 44 mm x
4 mm

13. Ball bearing

23. Castle nut M24 x 2

14. Shim kit

24. 3/16 x 2 Cotter pin

15. Snap ring

25. 3/8 Solid plug

16. Spacer
17. Shim 60.3 mm x 71.7 mm

26. M10 x 22 mm Hex head
screw

18. Snap ring

27. Vent plug

19. Seal

28. Cover

20. Washer, 1.58 x 3.13 x .04

29. Ball bearing

21. Snap ring

30. Spacer

Figure 16. Gearbox Assembly

22 Dealer Service

(Rev. 1/12/2007)
MAN0260 (8/6/2004)

Vertical Shaft Seal Replacement
Refer to Figure 15.
1. Disconnect and remove the driveline from the
gearbox.
2. Remove vent plug (15) and siphon gear lube from
housing through this opening.
3. Remove gearbox stand from mower deck.

Disassemble Gearbox
1. Remove top cover (28), Figure 16, from housing.
Turn gearbox upside down and pour out remaining
gear oil from gearbox.
2. Remove oil cap (11) (to be replaced).
3. Remove snap ring (10) and shim (9) from input
shaft (5).

4. Remove gearbox and pulley from stand (2).

4. Support gearbox in hand press and push on input
shaft (5) to remove bearing (8).

5. Remove vertical shaft seal. Replace with new seal
(see Seal Replacement, page 21).

5. Remove gear (7) from inside housing.

Vertical seal should be recessed in housing. Horizontal seal should be pressed flush with outside of
housing.
NOTE: Distortion to seal cage or damage to seal
lip will cause seal to leak.
6. Fill gearbox with SAE 80W or 90W gear lube until it
runs out the level plug.
7. Assemble gearbox and pulley to gearbox stand.
Attach gearbox stand to mower deck.

Horizontal Shaft Seal Replacement
1. Disconnect and remove the driveline from the
gearbox.
2. Remove vent plug (27), Figure 16, and siphon gear
lube from housing through this opening.
3. If the leak occurred at either end of horizontal shaft,
remove oil cap (11) and/or oil seal (1). Replace
with new one (see Seal Replacement, page 21).
4. Fill gearbox with SAE 80W or 90W gear lube until it
runs out the level plug.

Remove Gearbox from Mower
1. Disconnect and remove the rear driveline from the
gearbox.
2. Remove vent plug (15), Figure 15, and siphon gear
lube from housing through this opening.
3. Remove gearbox stand (2) from mower deck by
removing four hex screws (8).
4. Remove four cap screws (14) and washers (13)
and remove shield (12) from gearbox.
5. Remove castle nut (6) and hardware from output
shaft of gearbox.
6. Remove sheave (3) from gearbox.
7. Remove four bolts (10) that attach gearbox to
gearbox stand and remove gearbox.

MAN0260 (8/6/2004)

6. Remove oil seal (1) from front of housing (to be
replaced).
7. Remove snap ring (2) and shim (3) from front of
housing.
8. Remove input bearing (4) by using a punch and
hammer from outside of housing.
9. Support housing in vise in a horizontal position.
10. The castle nut (23) and cotter pin (24) are already
removed with the drive sheave. Remove the snap
ring (18), washer (20), and seal (19).
11. Remove output shaft (12) and bearings by using a
punch and hammer and tap on top to drive down.
12. Inspect gears for broken teeth and wear. Some
wear is normal and will show on laded side. Forged
gear surfaces are rough when new. Check that
wear pattern is smooth.
13. Inspect vertical and horizontal shafts for grooves,
nicks, or bumps in the areas where the seals seat.
Resurface any damage with emery cloth.
14. Inspect housing and caps for cracks or other
damage.

Reassemble Gearbox (RD60, RD74 shown,
RDC54 similiar)
Refer to Figure 16.
NOTE: Repair to this gearbox is limited to replacing
bearings, seals, and gaskets. Replacing gears, shafts,
and a housing is not cost effective. Purchasing a complete gearbox is more economical.
1. Clean housing, paying special attention to areas
where seals will be installed.
2. Wash housing and component thoroughly. Select a
clean area for gearbox assembly. Replace all seals
and bearings. All parts must be clean and lightly
oiled before reassembling.

Dealer Service 23

RD60 & RD72
3. Install upper output bearing (13), shims (14), and
snap ring (15) on output shaft (12). Use new shims
equal to the thickness of the original shims.
4. Press output shaft assembly into housing from the
bottom opening.
5. Install spacer (16), lower output bearing (13),
shims (17), and snap ring (18) in bottom of
housing.
RDC54
3. Install shims (14), upper output bearing (8), spacer
(16), lower output bearing (8), shims (17), and
snap ring (15) on output shaft. Use new shims
equal to the thickness of the original shims.
4. Press output shaft assembly into housing from the
bottom opening.
5. Install snap ring (18) in bottom of housing.
All Models
6. Apply grease to lower seal lips (19), and press seal
over output shaft (5), using a round tube of the
correct diameter. Be sure not to damage the seal
lip. Press in housing so that the seal is recessed.
7. Insert protective washer (20) (RD60 & RD72 only)
by hand.
8. Install snap ring (21) and position it together with
seal (19) by pressing it into position. Verify that the
snap ring is seated properly.
9. Press bearing (8) into the housing, using a round
tube of the correct diameter and a hand press.
Secure with shims (9) and snap ring (10).

17. Press in input seal (1), using a round tube of the
correct diameter. Be careful not to damage the seal
lip.
18. Press oil cap (11) on to the rear cover of housing,
using a round tube of the correct diameter.
19. Check the gearbox housing for leaks by plugging
all holes except one. Apply 4 psi compressed air
and immerse the gearbox in water to verify that
there are no leaks.
20. Remove the gearbox from water and dry off with
compressed air. Add SAE 80W or 90W EP oil until
it runs out of the side level hole. Tighten all plugs.

Install Gearbox
NOTE: Gearbox is heavy: do not attempt to move without mechanical assistance.
1. Set gearbox on gearbox stand and fasten with
bolts and nuts. Torque bolts to 175 lbs-ft.
2. Attach drive sheave to output shaft. Secure using
castle nut and hardware previously removed.
3. Attach gearbox stand to mower using four hex
screws.

Install Drive Sheave
1. When gear stand is installed on mower, dimension
A (from the top of the mower deck to the center line
of the drive pulley) must be 2-1/16" (±1/32"). This is
a critical dimension and must be carefully adjusted
for proper belt life. Add or subtract shim washers
under idler pulley to align with drive pulley.
2. Tighten gear stand hardware.

10. Install key (6) on input shaft (5).

3. Fill gearbox half full with SAE 90W gear lube.

11. Place gear (7) through top of housing and align the
two gears so they match.

4. Check level after waiting five minutes to permit
lube to work through bearings. Add lube, if
necessary, until gearbox is half full.

12. While holding gear (7) in place, slide input shaft (5)
through the gear and bearing (8).
13. Slide spacer (29) (RDC54 only) and bearing (4)
over input shaft (5) and press into housing, using a
round tube of the correct diameter and a hand
press.

5. Replace driveline shield. Attach driveline to
gearbox.

14. Slide shim (3) over input shaft and secure with
snap ring (2).
15. Check input shaft end float by moving the input
shaft by hand. If the end float is more than .012",
insert shim (9) between the rear bearing (8) and
snap ring (10).
16. Check that gear backlash is between .006" and
.016". You should not have to adjust the backlash.

24 Dealer Service

MAN0260 (8/6/2004)

UNIVERSAL JOINT REPAIR
1. Yoke
2. Cup and bearings
3. Snap ring
4. Journal cross

CD1386

Figure 19

Figure 17. U-Joint Exploded View

U-Joint Disassembly
1. Remove external snap rings from yokes in four
locations as shown in Figure 18.

CD1387

Figure 20
CD1385A

Figure 18
2. With snap rings removed, support drive in vise,
hold yoke in hand and tap on yoke to drive cup up
out of yoke. See Figure 19.
3. Clamp cup in vise as shown in Figure 20 and tap
on yoke to completely remove cup from yoke.
Repeat Step 2 & Step 3 for opposite cup.
4. Place universal cross in vise as shown in Figure 21
and tap on yoke to remove cup. Repeat Step 3 for
final removal. Drive remaining cup out with a drift
and hammer.

CD1388

Figure 21

MAN0260 (8/6/2004)

Dealer Service 25

U-Joint Assembly
1. Place seals securely on bearing cups. Insert cup
into yoke from outside and press in with hand
pressure as far as possible. Insert journal cross
into bearing cup with grease fitting away from
shaft. Be careful not to disturb needle bearings.
Insert another bearing cup directly across from first
cup and press in as far as possible with hand
pressure.
2. Trap cups in vise and apply pressure. Be sure
journal cross is started into bearings and continue
pressure with vise, squeezing in as far as possible.
Tapping the yoke will help.
3. Seat cups by placing a drift or socket (slightly
smaller than the cup) on cup and rap with a
hammer. See Figure 22. Install snap ring and
repeat on opposite cup.
4. Repeat Step 1 & Step 2 to install remaining cups in
remaining yoke.
5. Move both yokes in all directions to check for free
movement. If movement is restricted, rap on yokes
sharply with a hammer to relieve any tension.
Repeat until both yokes move in all directions
without restriction.

26 Dealer Service

Figure 22

MAN0260 (8/6/2004)

ASSEMBLY INSTRUCTIONS
DEALER SET-UP INSTRUCTIONS
Assembly of this mower is the responsibility of the
Woods dealer. It should be delivered to the owner completely assembled, lubricated, and adjusted for normal
cutting conditions.
Complete Dealer Check Lists on page 31 when you
have completed the assembly.

Install A-Frame Arms
1. Loosen lock nuts (52) at lower hitch point and
install A-frame arms (13) as shown.
2. Tighten nut securely.
3. Repeat for opposite side.

The mower is shipped partially assembled. Assembly
will be easier if components are aligned and loosely
assembled before tightening hardware. Recommended
torque values for hardware are located on page 43.
Select a suitable working area. Open parts boxes and
lay out parts and hardware to make location easy.
Refer to illustrations, accompanying text, parts lists and
exploded view drawings.

WARNING
Before working underneath, carefully read Operator’s Manual instructions, disconnect driveline,
raise mower, securely block up all corners with
jackstands, and check stability. Secure blocking
prevents equipment from dropping due to hydraulic leak down, hydraulic system failures, or
mechanical component failures.

Uncrate Mower
1. Remove sides and top of mower shipping crate.

CD6497

13.
14.
15.
16.
25.
51.
52.
54.
55.
56.

A-frame arms
Rear offset link arms
Top link U-bracket
Sleeve 1-1/4 x 1-3/4 x 2-3/4
Sleeve 5/8 x 1 x 7/16
1/2 NC Flanged lock nut
5/8 NC Flanged lock nut
5/8 Standard flat washer
1/2 NC x 1-1/4 HHCS GR5
5/8 NC x 2-1/2 HHCS GR5

Figure 23. A-Frame Arms Installed

2. Remove lag screws and brackets that secure
mower to crate base.
3. Remove driveshaft wired to mower deck.

(Rev. 1/13/2006)
MAN0260 (8/6/2004)

Assembly 27

Install Rear Offset Link Arms

Install Driveshaft

1. Loosen nut (51) and bolt (55) at rear frame lug and
attach rear offset link arm (14) as shown in Figure
24. (Do not use wheel tube bolt.)

1. Slide QD yoke of driveshaft assembly onto
gearbox shaft. Make sure QD yoke pin is seated
securely in groove of gearbox shaft.

2. Repeat for opposite side.

2. Attach shield anti-rotation chain to drive shield.

3. Do not tighten at this time.

Fill Gearbox
CD6497A-1

1. Make sure vent plug hole is clear. Fill gearbox halffull with high quality gear oil that has a viscosity
index of 80W or 90W and an API service rating of
GL-4 or GL-5.
2. Fill gearbox until oil runs out the side plug on
gearbox.
3. Pour in one pint of gear lube, wait five minutes and
add additional gear lube until it just comes out of
side hole.

14.
51.
55.

Rear offset link arm
Nut, flanged lock 1/2 NC
1/2 NC x 1-1/4 HHCS GR5

Figure 24. Right Rear Offset Link Installed

4. Allow an additional five minutes for the lube to flow
through bearings, then check to make sure oil level
is at bottom of side hole. Replace side plug. Install
vent plug.

IMPORTANT
■

Gearbox is not filled at the factory. Prior to
delivery, make sure each gearbox is filled half-full
with 80W or 90W API GL-4 or GL-5 gear lube.

Install Chain Shielding (Optional)

Install Top Link
1. Insert cap screw (54) through A-frame arms (13),
U-bracket (15), sleeve (16) and rear offset link
arms (14) and tighten securely with nut (51).

3.
14.
15.

Shield, chain plate
Bolt, carriage 3/8 NC x 1
Nut, flanged lock 3/8 NC

2. Tighten hardware on rear frame lug and offset link.

15
14

3
CD6497-2

13.
14.
15.
16.
51.
54.

A-frame arms
Rear offset link arms
Link, U-bracket
Sleeve, .62 x .84 x 2.75
Nut,flanged lock 1/2 NC
Screw, HHCS 1/2 NC x 4-3/4 GR5

Figure 25. Top Link Assembled

28 Assembly

CM768

Figure 26. Chain Shielding Installed
(RD60 & RD72 Only)

CM757

(Rev. 1/13/2006)
MAN0260 (8/6/2004)

1.
2.
3.
4.
5.
6.

1/4 Pin
3-Link 1/4 proof chain
Shield, chain plate
Sleeve 1/2 x 3/4 x 1/2
3/8 NC x 1-1/4 Carriage bolt
3/8 NC Flanged lock nut

Figure 27. Chain Shield Installed (RDC54 Only)

DANGER
Full chain shielding, designed to reduce the
possibility of thrown objects, must be installed
when operating in populated areas or other areas
where thrown objects could injure people or damage property. If this machine is not equipped with
full chain shielding, operation must be stopped
when anyone comes within several hundred feet.
1. Install chain shielding plate (3) to rear mower frame
as shown.
2. Secure with carriage bolts (14) and flanged lock
nuts (15).
3. Insert carriage bolts from bottom upward as
shown.

Install Quick Hitch Kit (Optional)
(RD60 & RD72 Only)
NOTE: Figure 28 shows RD60. Other models use the
same assembly instructions.
NOTE: This kit allows mower to fit only Cat. 1 standard
ASAE quick hitch.

(Rev. 1/13/2006)
MAN0260 (8/6/2004)

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

Offset link, .38 x 2 x 25.88 (A-frame bars)
38" Long chain
Sleeve, .91 x 1.44 x 1.25
1/2 NC x 6 Cap screw
1/2 Flat washer
Sleeve, .5 x .75 x 3.38
1/2 NC Flange lock nut
Sleeve, .875 x 1.125 x .593 HT
7/8 Flat washer
Sleeve, .81 x 1.25 x 1.81
Figure 28. Quick Hitch Kit Installation

1. Attach offset link (1) to mounting pins, using 7/8"
sleeve (8) and flat washer (9). Do not tighten
hardware.
2. Attach upper end of offset link to pivot link, using
flat washer (5), sleeves (6 & 10), flange lock nut
(7), and 1/2" x 4-3/4" cap screw.
3. Remove rear offset links and replace with chains
(2).
4. Attach chain to top of A-frame as shown, using cap
screw (4), flat washer (5), and nut. Attach opposite
end of chain (2) to rear mower frame as shown.
5. Cut chain to length (RD60 - 40", RD72 45"). Vary
length slightly as desired. Twist chain to make finite
adjustments in length until unit lifts level.
NOTE: Do not bottom out the drive on front of
deck.
6. Install sleeve (3) on mounting pins and retain with
klik pin.

Assembly 29

NOTES

Install Front Roller (Optional)
1. Insert four carriage bolts (8) through the front
mower frame from inside out.
2. Place roller bracket (2) over bolts; then install
flange lock nuts (9) on bolts and tighten.
3. Place front roller (1), sleeve (3), bearings (4), and
washers (5) in roller bracket as shown in Figure 29.
4. Insert cap screw (3) through bracket and roller.
5. Secure with flanged lock nut (2). Do not
overtighten, roller must spin freely.

CD6310

1. Roller
2. Roller bracket
3. Spacer
4. Bearing
5. 1/2 Flat washer SAE
6. 1/2 NC x 9 HHCS GR5
7. 1/2 NC Flanged locknut
8. 3/8 NC x 1-1/4 Carriage bolt
9. 3/8 NC Flanged locknut
Figure 29. Front Roller Installation

30 Assembly

MAN0260 (8/6/2004)

DEALER CHECK LISTS
DEALER PRE-DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
Inspect the equipment thoroughly after assembly to
ensure it is set up properly before delivering it to the
customer.
The following check lists are a reminder of points to
inspect. Check off each item as it is found satisfactory
or after proper adjustment is made.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check that shields and guards are properly
installed and in good condition. Replace if damaged.

___ Check all bolts to be sure they are properly
torqued.
___ Check that all cotter pins and safety pins are
properly installed. Replace if damaged.
___ Check and grease all lubrication points as identified in “lubrication information” on page 14.
___ Gearboxes are not filled at the factory. Prior to
delivery, fill as specified in the "Service, lubrication information" on page 14 and check to see
that there are no leaking seals.
___ Check that blades have been properly installed.

DEALER DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
___ Show customer how to make adjustments and
select proper PTO speed.
___ Instruct customer how to lubricate and explain
importance of lubrication.
___ Point out the safety decals. Explain their meaning and the need to keep them in place and in
good condition. Emphasize the increased safety
hazards when instructions are not followed.
___ Present Operator's Manual and request that
customer and all operators read it before operating equipment. Point out the manual safety
rules, explain their meanings and emphasize
the increased safety hazards that exist when
safety rules are not followed.

___ Explain to customer the potential crushing hazards of going underneath raised equipment.
Instruct that before going underneath to disconnect the driveline, securely block up all corners
with jackstands and to follow all instructions in
the "Service, blocking methods" section of the
Operator’s Manual. Explain that blocking up
prevents equipment dropping from hydraulic
leak down, hydraulic system failures, or
mechanical component failures.

___ Show customer how to make sure driveline is
properly installed and that spring-activated locking pin or collar slides freely and is seated in
groove on tractor PTO shaft.

___ For mounted units, add wheel weights, ballast in
front tires, and/or front tractor weight to enhance
front end stability. A minimum 25% of tractor
and equipment gross weight must be on front
tractor wheels. When adding weight to attain
25% of tractor and equipment weight on front
tractor wheels, you must not exceed the ROPS
weight certification. Weigh the tractor and
equipment. Do not estimate!

___ Show customer the safe, proper procedures to
be used when mounting, dismounting, and storing equipment.

___ Make customer aware of optional equipment
available so that customer can make proper
choices as required.
___ Point out all guards and shields. Explain their
importance and the safety hazards that exist
when not kept in place and in good condition.

(Rev. 1/12/2007)
MAN0260 (8/6/2004)

Dealer Check Lists 31

NOTES

32 Dealer Check Lists

MAN0260 (8/6/2004)

PARTS INDEX

Rear Discharge Mowers:
RDC54
RD60
RD72

MAIN FRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 & 35
GEARBOX ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
RDC54 DRIVELINE ASSEMBLY ( COMER) . . . . . . . . . . . . . . . . . . . . . 37
RD60 & RD72 DRIVELINE ASSEMBLY (COMER) . . . . . . . . . . . . . . . . 38
DRIVELINE ASSEMBLY (WALTERSCHEID TWO-LOBE) . . . . . . . . . . 39
BLADE & SPINDLE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
REAR CHAIN SHIELDING ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . 41
FRONT ROLLER ASSEMBLY (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . 42
QUICK HITCH (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

(Rev. 12/15/2006)
MAN0260 (8/6/2004)

Parts 33

RDC54, RD60 & RD72 MAIN FRAME ASSEMBLY
36 - COMPLETE DECAL SET
37 - SAFETY DECAL SET

REF RDC54 PART
1
2
3
4
5

----1008044
1008022
1008023
1008024

34 Parts

RD60 PART

RD72 PART

QTY

----1008044
1008069
1008069
1008167

----1008044
1008166
1008166
1008167

1
1
1
1
1

DESCRIPTION
Main frame (not sold separately)
Idler arm
Right shield
Left shield
Center shield

(Rev. 11/24/2006)
MAN0260 (8/6/2004)

RDC54, RD60 & RD72 MAIN FRAME ASSEMBLY
REF RDC54 PART
6
7
8
8
9
10
11
12
13
14
15
16
17
17
18
18
19
19
20
21
22
23
23
24
25
26
27
28
29
30
31
31
32
33
34
35
36
37

1008025
1008028
1008030
1008032
1008045
1008056
----1006649
19579
19056
19605
64814
1008097
1008096
19749
29368
24993
65578
65130
65129
27542
20409
N/R
N/R
484
20644
67283
67284
67131
1002048
1008098
1020903
N/R
1008020
1004656
1004657
1008196
53591

REF

PART

12305

50
51
52
53
54
55
56
57

23479
11900
19025
23479
692
6100
941
19024

*
*
*
*
*
*
*

58
59

3489
12296

RD60 PART

RD72 PART

QTY

1008085
1008169
1008030
1008032
18824
1008056
----1006648
19579
55331
19605
64814
1008097
1008096
19749
29368
24993
65578
65130
65129
27542
N/R
33661
1791
484
20644
67283
67284
67131
1002048
1008099
1009508
1008113
1008020
1004656
1004657
1008196
53591

1008125
1008169
1008030
1008032
18824
1008056
----1006648
19579
19578
19605
64814
1008097
1008096
19749
29368
24993
65578
65130
65129
27542
N/R
33661
1791
484
18879
67283
67284
67131
1002048
1008099
1009508
1008113
1008020
1004656
1004657
1008196
53591

2
1
4
4
2
1
3
1
2
2
1
1
4
4
4
4
8
8
12
4
4
2
2
2
3
1
2
1
1
1
1
1
1
1
1
2
1
1

DESCRIPTION
Caster tube
Gearbox stand
Caster yoke (pneumatic tire)
Caster yoke (solid tire)
Hitch
Gearbox sheave
Spindle (see page 40)
Gearbox (see page 36)
A-frame arm
Rear offset link arm
Top link U-bracket
Sleeve 1-1/4 x 1-3/4 x 2-3/4
Wheel, 10" pneumatic (includes items 19) -orWheel, 10" solid (includes items 19)
Sleeve 1/2 x 3/4 x 4-1/16 (pneumatic tire) -orSleeve 1/2 x 3/4 x 3-3/8 (solid tire)
Ball bearing (pneumatic tire) -orFlanged bushing (solid tire)
1" Height spacer
1/2" Height spacer
7/16 Klik pin
Clevis pin 7/8 x 3 -orPin, Cat. 1 w/lockwasher & nut
Sleeve 5/8 x 1 x 9/16
Sleeve 5/8 x 1 x 7/16
Belt
5" Idler
Shoulder sleeve
Spring
Shield
Driveline (Walterscheid)
Driveline (Comer)
Sleeve 1-1/4 x 1-3/4 x 3/4
Manual tube holder
Manual tube - PVC
Caplug
Complete decal set
Safety decal set

DESCRIPTION

REF

1/2 NC x 5-1/2 HHCS GR5 (pneumatic tire) -or1/2 NC x 5 HHCS GR5 (solid tire)
1/2 NC Flanged locknut
5/8 NC Flanged locknut
1/2 NC x 5 HHCS GR5
5/8 Standard flat washer
1/2 NC x 1-1/4 HHCS GR5
5/8 NC x 2-1/2 HHCS GR5
5/8 NC x 1-3/4 Hex head flanged cap
screw GR5
1/2 NC x 3 HHCS GR5
1/4 - 28 Grease fitting

60
62
63
65
66
67
68
69
70
71
72
73

(Rev. 12/15/2006)
MAN0260 (8/6/2004)

PART
854
1008011
18270
39254
4378
62153
6593
20893
51946
64803
52893
24576

DESCRIPTION
*
*
*
*

1/2 Standard flat washer
3/8 NC sq nut w/retainer
3/16 Safety pin
M8 x 1.25 x 16 mm Hex head screw
5/16 Standard flat washer
3/8 NC x 1 Hex flange serrated
1/4 x 1/4 x 1 Key
25 x 44 x 4 mm Flat washer
M24 x 2 Hex castle nut
3/16 x 2 Cotter pin
PTO Hanger bracket
1/2 NC x 1-3/4 HHCS GR5
Standard Hardware, Obtain Locally

Parts 35

RDC54, RD60 & RD72 GEARBOX ASSEMBLY

REF

RDC54
PART

A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

1006649
39275
1007861
1007865
51850
N/S
20894
N/S
20890
1007864
57466
57374
N/S
----1007866
1007859
1007860

QTY

1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1

RD60 / 72
QTY
PART
1006648
39275
1007861
1007865
51850
N/S
20894
N/S
20890
1007864
57466
57374
N/S
20891
1007863
20895
20886

36 Parts

1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1

DESCRIPTION
Complete gearbox
Seal
Snap ring
Shim kit
Ball bearing
Input shaft
Key 8 x 10 x 30 mm
Input gear
Ball bearing
Shim kit
Snap ring
Oil cap
Output shaft & gear
Ball bearing
Shim kit
Snap ring
Spacer

REF

RDC54
PART

QTY

17
18
19
20

1007862
57466
57463
-----

1
1
1
1

1007862
39251
20900
20888

1
1
1
1

21
22

1007858
20893

1
1

20897
20893

1
1

23
24
25
26

51946
64803
N/S
N/S

1
1*
1*
4*

51946
64803
N/S
N/S

1
1*
1*
4*

27
28
29

39325
1007873
1007857

1
1
1

39325
1007873
-----

1
1
1
*

RD60 / 72
QTY
PART

DESCRIPTION
Shim kit
Snap ring
Seal
Washer, 1.58 x 3.13 x
.04
Snap ring
Washer 25 x 44 x 4
mm
Castle nut M24 x 2
3/16 x 2 Cotter pin
3/8 Solid plug
M10 x 22 mm Cap
screw
Vent plug
Cover
Spacer
Standard hardware,
obtain locally

(Rev. 6/10/2005)
MAN0260 (8/6/2004)

RDC54 DRIVELINE ASSEMBLY (COMER)

REF

PART

QTY

DESCRIPTION

REF

PART

QTY

DESCRIPTION

1020903

Complete driveline assembly

30917

Chain shielding tether

1001300

Complete collar yoke C12 1-3/8 - 6

1001340

Lock collar repair kit

38478

Cross and bearing kit

1001302

Flexible pin

1019442

Outer cone fix ring

1001301

Outer yoke tube

1001305

Flexible pin

30922

Protection fixing screw

1019444

Inner cone fix ring

1001306

Inner tube yoke

1021554

Complete shield

(Rev. 1/12/2007)
MAN0260 (8/6/2004)

Parts 37

RD60 & RD 72 DRIVELINE ASSEMBLY (COMER)

REF
A

PART
1009508

QTY
1

DESCRIPTION

REF

PART

QTY

DESCRIPTION

Complete driveline assembly

30917

Chain shield tether

1001340

Lock collar repair kit

1001300

Complete collar yoke C12 1-3/8 - 6

38478

Cross and bearing kit

1001302

Flexible pin

1019442

Outer cone fix ring

1001301

Outer yoke tube

30922

Protective fixing screw

1001305

Flexible pin

Inner cone fix ring

1001306

Inner tube yoke

1021323

Complete shield

1019444

38 Parts

(Rev. 1/12/2007)
MAN0260 (8/6/2004)

RDC54, RD60 & RD72 DRIVESHAFT
WALTERSCHEID (TWO-LOBE SHAFT)

REF

PART

QTY

DESCRIPTION

REF PART

QTY

DESCRIPTION

1008098

Complete driveline RDC54 -or-

40776

Bearing ring, guard

1008099

Complete driveline RD60, RD72

40777

Chain, guard anti-rotation

40571

Yoke, 1-3/8 - 6-Spline QD

40778

Screw, guard

154

U-Joint repair kit L14R

40759

40775

Pin, spring 10 mm x 65 mm

Guard, outer half (also includes items 8,
9, 10)

40572

Yoke, inner profile

40761

Guard, inner half (also includes items 8,
9, 10)

40589

Slide lock collar repair kit (without yoke)

40583

Drive tube, inner profile

40592

Drive tube, outer profile

40573

Yoke, inner profile

(Rev. 1/12/2007)
MAN0260 (8/6/2004)

Parts 39

RDC54, RD60 & RD72 BLADE & SPINDLE ASSEMBLY

REF

PART

QTY

DESCRIPTION

1009080

Complete spindle assembly (includes
1, 2, 4, 5 through 12, 14 & 15)

64518

3/8 NF x 1 HHCS GR5

70005

Cup washer

1008059

Sheave (RDC54) -or-

1008057

Sheave (RD60) -or-

1008040

Sheave (RD72)

1008055

Spacer

72933

Spindle bearing

14350*

3/8 NC Flange locknut

1972*

1/4 Tapered grease fitting

1008053

Spindle housing

976*

3/8 NC x 1-1/2 HHCS GR5

1008052

Spacer

70072*

Square key

1008042

Shaft assembly

78127KT

Blade kit, high suction 18.7" (includes
3 blades)(RDC54) -or-

1001513KT

Blade kit, high suction 21" (includes 3
blades)(RD60) -or-

1008199KT

Blade kit, high suction 25" (includes 3
blades)(RD72)

10635

Cup washer

1008095

5/8 NF x 2 HHCS GR5

Standard Hardware - Obtain Locally

RDC54, RD60, RD72 BELT GUIDE (OPTIONAL)

REF

40 Parts

PART

QTY

DESCRIPTION

1008181

Belt guide kit

N/A

Belt guide

3231*

3/8 NC x 2 Cap screw GR5

21575*

3/8 SAE Flat washer

14350*

3/8 NC Flange lock nut (not included)

(Rev. 12/15/2006)
MAN0260 (8/6/2004)

RD60 & RD72 REAR CHAIN SHIELDING ASSEMBLY (OPTIONAL)

REF
A

PART

QTY

55348

DESCRIPTION
Chain shield assembly (RD60)

53566

1007854

Pin, 40 to 42 chains (for RD60 only) -or-

Chain shield assembly (RD72)

1007856

Pin, 52 to 54 chains (for RD72 only)

4763

Chain, 3-link, 1/4 proof (use 54 for RD60; 60 for
RD72
15
CD4997A

REF

14
3
1

PART

QTY

DESCRIPTION

55345

53554

Shield, chain plate (for RD72 only)

Bolt, carriage 3/8 NC x 1

14
15

14350

Shield, chain plate (for RD60 only) -or-

Nut, flanged lock 3/8 NC
*

Standard Hardware, Obtain Locally

RDC54 REAR CHAIN
SHIELD ASSEMBLY (OPTIONAL)

REF
A

1008038

1007854

(Rev. 12/15/2006)
MAN0260 (8/6/2004)

PART

QTY

DESCRIPTION
Chain shield assembly

1/4 Pin

4763 49 3-Link 1/4 proof chain

1008037

Chain shield plate

22086

Sleeve 1/2 x 3/4 x 1/2

24890*

3/8 NC x 1-1/4 Carriage bolt

14350*

3/8 NC Flanged locknut

Standard Hardware, Obtain Locally

Parts 41

RDC54, RD60 & RD72 FRONT ROLLER ASSEMBLY (OPTIONAL)

REF

PART

QTY

DESCRIPTION

1008035KT

Front roller kit, complete

1006418

Roller

1008034

Roller bracket

1006420

Spacer

35193

Bearing

3598

1/2 Flat washer SAE

38107

1/2 NC x 9 HHCS GR5

11900

1/2 NC Flanged locknut

24890*

3/8 NC x 1-1/4 Carriage bolt

14350*

3/8 NC Flanged locknut

Standard Hardware, Obtain Locally

RD60 & RD72 QUICK HITCH KIT (OPTIONAL)

REF

42 Parts

PART

QTY

DESCRIPTION

1003692

Link, offset .38 x 2.0 x 15

1005401

Chain 3/8 proof coil 38 link

38214

Sleeve, .91 x 1.44 x 1.25

13563

Screw, HHCS 1/2 NC x 6 GR5

Washer, flat 1/2 ZP

29368

Sleeve, .50 x .75 x 3.38

11900

Nut, flange lock 1/2 NC

29281

Sleeve, 7/8 x 1-1/8 x 19/32 HT

Washer, flat 7/8

1003614

Sleeve, .81 x 1.25 x 1.81

Standard Hardware, Obtain Locally

(Rev. 12/15/2006)
MAN0260 (8/6/2004)

BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification

SAE SERIES
TORQUE
CHART

SAE Grade 2
(No Dashes)

SAE Grade 8
(6 Radial Dashes)

SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD

A
SAE 2

SAE 5

SAE 8

Diameter
(Inches)

Wrench
Size

lbs-ft

N-m

lbs-ft

N-m

lbs-ft

N-m

1/4"
5/16"

7/16"
1/2"

6
12

8
17

10
19

13
26

14
27

18
37

3/8"
7/16"

9/16"
5/8"

23
36

31
48

35
55

47
75

49
78

67
106

1/2"
9/16"

3/4"
13/16"

55
78

75
106

85
121

115
164

120
171

163
232

5/8"
3/4"

15/16"
1-1/8"

110
192

149
261

170
297

230
403

240
420

325
569

7/8"
1"

1-5/16"
1-1/2"

306
467

416
634

474
722

642
979

669
1020

907
1383

METRIC SERIES
TORQUE
CHART

Metric Bolt Head
Identification

8.8
Metric
Grade 8.8

10.9
Metric
Grade 10.9

COARSE THREAD

FINE THREAD

MARKING ON HEAD

Diameter &
Thread Pitch
(Millimeters)

Wrench
Size

N-m

lbs-ft

N-m

lbs-ft

N-m

lbs-ft

N-m

lbs-ft

Diameter &
Thread Pitch
(Millimeters)

6 x 1.0

10 mm

6 x 1.0

8 x 1.25
10 x 1.5

13 mm
16 mm

20
39

15
29

27
54

20
40

21
41

16
30

29
57

22
42

8 x 1.0
10 x 1.25

12 x 1.75
14 x 2.0

18 mm
21 mm

68
109

50
80

94
151

70
111

75
118

55
87

103
163

76
120

12 x 1.25
14 x 1.5

16 x 2.0
18 x 2.5

24 mm
27 mm

169
234

125
172

234
323

173
239

181
263

133
194

250
363

184
268

16 x 1.5
18 x 1.5

20 x 2.5

30 mm

330

244

457

337

367

270

507

374

20 x 1.5

22 x 2.5
24 x 3.0

34 mm
36 mm

451
571

332
421

623
790

460
583

495
623

365
459

684
861

505
635

22 x 1.5
24 x 2.0

30 x 3.0

46 mm

1175

867

1626

1199

1258

928

1740

1283

30 x 2.0

Typical Washer
Installations
Bolt

Metric 8.8

Lock Washer
Nut

Bolt Torque & Size Charts (Rev. 8/14/02)

Metric 10.9

Metric 8.8

Metric 10.9

Flat Washer

8/9/00

Appendix 43

BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

SAE Bolt Thread Sizes
5/16
3/8
1/2

5/8

3/4

7/8

100

125

150

175

Metric Bolt Thread Sizes
8MM
10MM

12MM

14MM

16MM

18MM

ABBREVIATIONS
AG .............................................................Agriculture

NC .................................................... National Coarse

ATF .............................. Automatic Transmission Fluid

NF..........................................................National Fine

BSPP........................... British Standard Pipe Parallel

NPSM ................... National Pipe Straight Mechanical

BSPTM .............. British Standard Pipe Tapered Male

NPT ........................................ National Pipe Tapered

CV .................................................. Constant Velocity

NPT SWF ....... National Pipe Tapered Swivel Female

CCW.............................................Counter-Clockwise

ORBM......................................... O-Ring Boss - Male

CW .............................................................Clockwise

P .........................................................................Pitch

F ..................................................................... Female

PBY .....................................................Power-Beyond

GA ................................................................... Gauge

psi........................................ Pounds per Square Inch

GR (5, etc.)..........................................Grade (5, etc.)

PTO ....................................................Power Take Off

HHCS ...................................... Hex Head Cap Screw

QD .................................................. Quick Disconnect

HT.......................................................... Heat-Treated

RH ............................................................Right Hand

JIC ............... Joint Industry Council 37° Degree Flare

ROPS ......................... Roll-Over Protective Structure

LH............................................................... Left Hand

RPM ...................................... Revolutions Per Minute

LT..........................................................................Left

RT...................................................................... Right

m .......................................................................Meter

SAE ........................ Society of Automotive Engineers

mm ............................................................. Millimeter

UNC.................................................... Unified Coarse

M ........................................................................ Male

UNF .........................................................Unified Fine

MPa ....................................................... Mega Pascal

UNS....................................................Unified Special

N.....................................................................Newton

44 Appendix

Bolt Torque & Size Charts (Rev. 8/14/2002)

INDEX
Assembly
Dealer Set-up Instructions 27
Gearbox
Fill Gearbox 28
Install
Chain Shielding 28
Driveshaft 28
Front Offset Links 27
Front Roller 30
Quick Hitch Kit 29
Rear Caster Arm 28
Rear Offset Link 28
Top Link 28
Uncrate Mower 27
Dealer Check List
Delivery (Dealer’s Responsibility) 31
Pre-Delivery (Dealer’s Responsibility) 31
Dealer Service
Blade Spindle
Repair 20
Blocking Method 20
Gearbox
Assemble 23
Disassemble 23
Install 24
Remove 23
Repair 21
Seal Installation 21, 23
Seal Replacement 21
Vertical Shaft Repair 23
Install Drive Sheave 24
Universal Joint
Assembly 26
Disassembly 25
Repair 25
General
Abbreviations 44
Bolt Size Chart 44
Bolt Torque Chart 43
General Information 4
General information 4
Introduction 2
Obtaining Replacement Manuals 2
Specifications 4
Warranty
Product 46
Replacement Parts 47

Technique 12
Tips 12
Removing Mower from Tractor 13
Tractor Stability 10
Owner Service
Belt
Install 16
Replace 15
Blade
Install 16
Service 16
Blocking Method 14
Chain Shielding 16
Lubrication
Driveshaft 16
Information 14
Points 16
Parts
Parts Index 33
Safety
Blocking Method 14, 20
Dealer Check List
Delivery (Dealer’s Responsibility) 31
Pre-Delivery (Dealer’s Responsibility) 31
Owner Check List
Owner Pre-Operation (Owners Responsibility)
13
Safety & Instructional Decals 8
Safety Rules 5, 6, 7
Safety Symbols Explained 2
Service
Install Blades 17
Remove Blades 16
Service Blades 16
Sharpen Blades 16
Spindle Repair
Assemble Spindle 21
Disassemble Spindle 20
Remove Spindle 20
Trouble Shooting 18
Belt Conditions 19
Mowing Conditions 18

Operation 10
Adjustment
Cutting Height 11
Cutting Height Chart 11
Tractor Top Link 11
Attach Mower to Tractor 10
Check List
Owner Pre-Operation (Owners Responsibility)
13
Front Caster Wheel Interference Check 12
Front Roller 12
Operating
On Uneven Terrain 13
(Rev. 1/12/2007)
MAN0260 (8/6/2004)

Index 45

WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________

From (Dealer): ___________________________________________

Model Number: ____________________________

Serial Number: ___________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Model Number
PHD25, PHD35, PHD65, PHD95, 1260, 2162, 3240, BB48, BB60, BB72, BB84,
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW180-2, BW1800, DS96,
DS120, RCC42, RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400,
7144RD-2, 9180RD-2, 9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
RDC54, RD60, RD72

Part or
Condition
Warranted

Duration (from date of delivery
to the original purchaser)

Gearbox
components

5 years

Gearbox
components

3 years (1 year if used in rental or
commercial applications)

RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,
9180RD-2, 9204RD-2

Blade spindles

3 years

BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126, BW180, BW1260,
BW1800, 1260, 2162, 3240

Rust-through

10 years

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery
or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:

Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
www.WoodsEquipment.com

F-3079 (Rev. 10/10/2006)

WARRANTY
(Replacement Parts For All Models Except Mow’n MachineTM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:

Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
www.WoodsEquipment.com

F-8494 (Rev. 6/23/2005)

PART NO.

MAN0260

Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
815-732-2141 tel
815-732-7580 fax
www.WoodsEquipment.com
© 2004 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2007:01:10 08:43:19-06:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2007:01:10 08:58:38-06:00
Metadata Date                   : 2007:01:10 08:58:38-06:00
Format                          : application/pdf
Creator                         : MAN0260 Rev. 1/12/2007
Title                           : Heritage Rear Discharge Mower RDC54, RD60 and RD72
Description                     : Cover, 3-19, 31, 37-39, 45 (No PN Changes)
Document ID                     : uuid:70e17159-71d1-445a-87a3-78a27583b1ee
Instance ID                     : uuid:3cf5275d-a3af-4c26-8d5a-fa980211a068
Page Count                      : 48
Subject                         : Cover, 3-19, 31, 37-39, 45 (No PN Changes)
Author                          : MAN0260 Rev. 1/12/2007
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools

Woods Equipment Rd60 Users Manual Heritage Rear Discharge Mower RDC54, And RD72

!! Woods-45 Woods Equipment Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

RD60 to the manual cb3a9fcc-3692-4928-be9e-921791297a6a

Navigation menu

Versions of this User Manual:

Views

Navigation