Woods Equipment Tl52 Users Manual Alitec Tiller TL52, TL73, TL84

TL52 to the manual 3ed750de-a001-44a4-9792-a91885811415

2015-02-05

: Woods-Equipment Woods-Equipment-Tl52-Users-Manual-408626 woods-equipment-tl52-users-manual-408626 woods-equipment pdf

Open the PDF directly: View PDF .
Page Count: 34

Download
Open PDF In Browser	View PDF

TL52
TL73
TL84

(Rev. 7/4/2008)

MAN0003

Effective Serial Numbers:
TL52A 4200690202
TL73A 4300730102
TL84A 5600020102

Tested. Proven. Unbeatable.

OPERATOR'S MANUAL

SKID STEER
TILLER

TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual
are completed before releasing equipment to the owner.
The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in
form included with the Operator’s Manual. If using the mail-in form, the dealer is to return the prepaid postage portion to
Woods, give one copy to the customer, and retain one copy. Failure to register the product does not diminish
customer’s warranty rights.
TO THE OWNER:
Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and
safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become
acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be
obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in
the United States and Canada call 1-800-319-6637.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces
provided:

Model: _______________________________

Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.
The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with
an exclamation mark) to indicate the degree of hazard for items of personal safety.

2 Introduction

Gen’l (Rev. 2/19/2008)

TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PARTS INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
HYDRAULIC FITTING TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . .26
QUICK COUPLER KITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .31
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . INSIDE BACK COVER

MAN0003 (Rev. 11/30/2006)

Introduction 3

GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your tiller. Read it carefully. It furnishes
information and instructions that will help you achieve
years of dependable performance. These instructions
have been compiled from extensive field experience
and engineering data. Some information may be general in nature due to unknown and varying operating
conditions. However, through experience and these
instructions, you should be able to develop procedures
suitable to your particular situation.

The illustrations and data used in this manual were current at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
Throughout this manual, references are made to right
and left direction. These are determined by standing
behind the equipment facing the direction of forward
travel.

SPECIFICATIONS
TL52

TL73

TL84

Dual Direct

Char-Lynn 2000 - 18.7

Ross ME180405 AAAB

3300 psi (228 bars)

5000 psi (245 bars)

Working Depth

0 - 6 Inches

Working Width

52 Inches (1321 mm)

73 Inches (1854 mm)

84 Inches (2134 mm)

Overall Width

60 Inches (1524 mm)

86 Inches (2184 mm)

97 Inches (2462 mm)

Overall Length

44 Inches (1118 mm)

Tines

RPM

@12 gpm (46 lpm)
148 rpm

@15 gpm (76 lpm)
247 rpm

@20 gpm (76 lpm)
247 rpm

@15 gpm (57 lpm)
185 rpm

@25 gpm (95 lpm)
309 rpm

@25 gpm (95 lpm)
432 rpm

@18 gpm (69 lpm)
22 rpm

@32 gpm (122 lpm)
395 rpm

@32 gpm (122 lpm)
432 rpm

Motor
Maximum Pressure

@40 gpm (152 lpm)
540 rpm

4 Introduction

MAN0003 (Rev. 11/30/2006)

SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be erased
by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident prevention are dependent upon the awareness, concern,
judgement, and proper training of personnel
involved in the operation, transport, maintenance
and storage of equipment.
It has been said “The best safety device is an
informed, careful operator.” We ask you to be that
kind of operator.

INSTALLATION
Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
After connecting hoses, check that all control
lever positions function as instructed in the Operator's Manual. Do not put into service until control
lever and equipment movements are correct.

TRAINING
Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
If you do not understand any part of this manual
and need assistance, see your dealer.
Know your controls and how to stop engine and
attachment quickly in an emergency.
Operators must be instructed in and be capable
of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.

Alitec Tiller SR (Rev. 11/30/2006)

Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gangrene, serious injury, or death will result. CONTACT A P HYS ICIA N IM ME DIATE LY IF FLU ID
ENTERS SKIN OR EYES. DO NOT DELAY.
Never allow children or untrained persons to
operate equipment.

PREPARATION
Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
Counterweight ballast may be required for
machine stability. Check your power unit manual or
contact your dealer.
Air in hydraulic systems can cause erratic operation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
p ut t i ng i n t o s e r v i c e o r a l l o w i n g a n y o n e t o
approach the equipment.
After connecting hoses, check that all control
lever positions function as instructed in the Operator's Manual. Do not put into service until control
lever and equipment movements are correct.
Protective hose sleeves must cover all hydraulic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
(Safety Rules continued on next page)

Safety 5

SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)

Be sure attachment is properly secured,
adjusted, and in good operating condition. Coupler
lockpins must be fully extended and properly
engaged into attachment retaining slots.
Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.

OPERATION
Improper operation can cause the machine to
tip or roll over and cause injury or death.
• Keep power unit lift arms and attachment as
low as possible.
• Do not travel or turn with power unit lift arms
and attachment raised.
• Turn only on level ground.
• Go up and down slopes, not across them.
• Keep the heavy end of the machine uphill.
• Do not overload the machine.
Never use attachment to carry loads that exceed
the rated operating capacity or other specifications
of the power unit. Check your power unit manual or
see your dealer for rated operating capacity.
Exceeding this capacity can cause machine to tip,
roll over, or present other hazards that can cause
injury or death.
Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.
Contact with high voltage, overhead power
lines, underground cables, gas lines, and other
hazards can cause serious injury or death from
electrocution, explosion, or fire.
Keep bystanders away from equipment.
Never direct discharge toward people, animals,
or property.

6 Safety

Do not operate or transport equipment while
under the influence of alcohol or drugs.
Operate only in daylight or good artificial light.
Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
Always comply with all state and local lighting
and marking requirements.
Do not allow riders. Do not lift or carry anybody
on the power unit or attachments.
Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt/operator restraint, place transmission in park
or neutral, engage brake and ensure all other controls are disengaged before starting power unit
engine.
Look down and to the rear and make sure area
is clear before operating in reverse.
Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
Do not operate or transport on steep slopes.
Do not stop, start, or change directions suddenly on slopes.
Use extreme care and reduce ground speed on
slopes and rough terrain.
Watch for hidden hazards on the terrain during
operation.
Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,
using proper procedure. Inspect and repair any
damage before resuming operation.
Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
Before making any adjustments on attachment,
stop engine and engage parking brake. Never
adjust or work on attachment while the power unit
or attachment is running.
(Safety Rules continued on next page)

Alitec Tiller SR (Rev. 11/30/2006)

SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)

MAINTENANCE
Before leaving operator's seat, follow power
unit manual instructions. Lower lift arms and put
attachment on the ground. Stop engine, remove
key, engage brake, and remove seat belt/operator
restraint.

Never perform service or maintenance with
engine running.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.

NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.

Make sure shields and guards are properly
installed and in good condition. Replace if damaged.

• Service work does not require going underneath.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.

Do not disconnect hydraulic lines until all system pressure is relieved. Lower unit to ground,
stop engine, and operate all hydraulic control
levers.

Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its components in any way.

Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.

Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifications and may be dangerous.

STORAGE

Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

Alitec Tiller SR (Rev. 11/30/2006)

Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)

Follow manual instructions for storage.
Keep children and bystanders away from storage area.

Safety 7

SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
1 - Serial Number Plate

2 - PN 54519

3 - PN D0200

WARNING

4 - PN D0209

FALLING OFF CAN RESULT IN BEING RUN OVER.
■ Skid steer must have ROPS and seat belt/operator restraint.

Keep seat belt/operator restraint securely fastened.
■ Never allow riders.

D0209

RAISED EQUIPMENT CAN DROP AND CRUSH.
■ Never go under raised equipment or raised skid steer lift

arms. They can drop from hydraulic or mechanical failure, or
moving control levers.
■ Service work does not require going under equipment. Read
manual instructions.
FALLING OFF OR GOING UNDER MACHINE CAN RESULT IN
SERIOUS INJURY OR DEATH.
54519-B

!
" ,

5 - PN 19924

WARNING
HIGH-PRESSURE HYDRAULIC OIL LEAKS CAN PENETRATE SKIN
RESULTING IN SERIOUS INJURY, GANGRENE OR DEATH.
n Check for leaks with cardboard; never use hand.
n Before loosening fittings: lower load, release pressure, and
be sure oil is cool.

19924-B

n Consult physician immediately if skin penetration occurs.

6 - PN D0404

WARNING

D0404-C

8 Safety

TO AVOID SERIOUS INJURY OR DEATH:
Read attachment and power unit manuals before you use,
service, or repair machine. Follow all safety rules and
instructions. (Manuals can be obtained from your dealer, or
in the United States and Canada call 1-800-319-6637.)
Use only when sitting in operator's seat with seat belt/
operator restraint fastened.
Before leaving operator's seat, follow power unit manual
instructions, lower lift arms and attachment to ground, stop
engine, remove key, engage brake, and remove seat belt/
operator restraint.
Never let children or untrained persons run equipment.

(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)

SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!

BE CAREFUL!
Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a
pressure washer; high-pressure water can enter through very small scratches or under edges of
decals causing them to peel or come off.
Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest
dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and
Canada call 1-800-319-6637.

(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)

Safety 9

OPERATION

WARNING
Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
■

The operator is responsible for the safe operation of this equipment. Operators must be
instructed in and be capable of the safe operation
of the equipment, its attachments and all controls.
Do not allow anyone to operate this equipment
without proper instructions.

___ Keep all bystanders away from equipment working area.
___ Check that all hydraulic hoses and fittings are in
good condition and not leaking before starting
power unit.
___ Check that hoses are not twisted, bent sharply,
kinked, frayed or pulled tight. Replace any damaged hoses immediately.
___ Make sure power unit ROPS and seat belts are in
good condition. Keep seat belt securely fastened
during operation.

TILLER INSTALLATION
Read instructions in the skid steer operator’s manual
for connecting and removing attachment.
Place the couplers in the disengaged position as
shown in Figure 1. Rotate the skid steer attachment
slightly forward and fully lower the lift arms.

Skid steers must be equipped with an auxiliary
hydraulic system capable of supplying continuous
flow for hydraulic motor operation.

PRE-OPERATION CHECK LIST
Owner’s Responsibility
___ Review and follow all safety rules and decals.
See safety rules on page 5 and safety decals on
page 8.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check that all shields and guards are properly
installed and in good condition. Replace if damaged.
___ Check that equipment is properly and securely
attached to skid steer.
___ Check that all hardware and cotter pins are properly installed and secured.
___ Do not allow riders.

10 Operation

DP1

Figure 1.
Pull forward to the attachment as shown in Figure 2.
Make sure the outside of the skid steer attach (1) is
aligned with the inside of the tiller attach (2). Continue
to pull forward until the skid steer attach makes contact
with the tiller attach. Raise the skid steer arms until the
top of the skid steer attach contacts the top latch bar
(3) on the tiller.

MAN0003 (Rev. 11/30/2006)

depth skid for the desired cutting depth. Reinstall the
two bolts and torque to 250 lbs-ft (325 N-m).
3

2
1
DP2

Figure 2.
Roll the skid steer arms back until the tiller is completely off the ground. Engage the parking break on the
skid steer. Stop engine and relieve the back pressure in
the auxiliary hydraulic system. Exit the skid steer.
Move the coupler pins to the engaged position. Hook
up the auxiliary hydraulic hoses. Be sure they are
routed to prevent any hose interference. Check the
attach pins (4) to be sure they are fully engaged in the
attach bracket as shown in Figure 3.

1. 5.50" Cutting Depth
2. 4.25" Cutting Depth
3. 2.25" Cutting Depth
6.00" Cutting Depth if Skid is Removed
Figure 4.

TILLER OPERATION

WARNING
■

Read and understand the tiller and skid steer
operator’s manuals before operating the tiller. Failure to do so may result in death, serious personal
injury or properly damage.
The tiller is a hydraulic powered attachment intended to
cultivate soil. The tiller attachment operation is bi-directional; it will operate with tines rotating in either direction.
The TL52 has an offset mounting configuration to allow
the right tracks to be covered when the skid steer
moves in reverse for finishing the tilling operation.

DP3

Figure 3.

TILLER DEPTH ADJUSTMENT
All tiller models have four depth settings. Moving the
depth skid location allows the depth setting to be
changed. Figure 4 shows the cutting depth for the four
depth positions. When making adjustments, be sure
that both skids are set at the same position.

The performance of the tiller can vary significantly
depending upon the way it is used. The tiller attachment requires a minimum hydraulic supply. For requirements on each model see specifications on page 4.

To change the depth skid position, lower the tiller to the
ground so the weight is supported on the tines.
Remove the two bolts from each depth skid. Adjust the

MAN0003 (Rev. 11/30/2006)

Operation 11

NOTICE
■

To avoid tiller and motor damage, stop prime
mover hydraulic flow. Allow tiller to stop completely before changing direction of rotation.
For maximum productivity and to maintain optimal
operation, keep chassis free of residue build up and
replace worn or broken tines.
Never raise the attachment more than 24" off the
ground. When loading, keep the attachment as low to
ramps and trailers as possible.
For finish tilling operation, the tiller may be operated in
the reverse direction with the tines rotating in a clockwise direction when viewed from the left side of the
machine.

CLEANING
After Each Use
●

Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.

●

Inspect machine and replace worn or damaged
parts.

●

Replace any safety decals that are missing or not
readable.

Periodically or Before Extended Storage
●

Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.

●

Remove the remainder using a low-pressure water
spray.

Roll the skid steer arms fully back and lower the arms
completely. Activate auxiliary hydraulics and make sure
the tines are rotating in the desired direction. Bring skid
steer to high idle, slowly tilt the tiller forward until the
depth skids contact the ground. Move the skid steer in
the desired direction of travel.

1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.

TRANSPORT

NOTICE
■

When transporting the attachment, be sure the
tines do not contact the ground as this may cause
the drum to turn resulting in damage to the motor.
Roll the skid steer arms fully back and raise the attachment 12" to 15" from the ground. Avoid excessive
ground speed and sudden maneuvers. Never raise the
attachment more than 24" off the ground. When loading, keep the attachment as low to ramps and trailers
as possible.

WARNING
Improper operation can cause the machine to
tip or roll over and cause injury or death.
• Keep power unit lift arms and attachment as
low as possible.
• Do not travel or turn with power unit lift arms
and attachment raised.
• Turn only on level ground.
• Go up and down slopes, not across them.
• Keep the heavy end of the machine uphill.
• Do not overload the machine.
Look down and to the rear and make sure area
is clear before operating in reverse.

12 Operation

●

Inspect machine and replace worn or damaged
parts.

●

Sand down scratches and the edges of areas of
missing paint and coat with spray paint of matching
color (purchase from your dealer).

●

Replace any safety decals that are missing or not
readable (supplied free by your dealer). See Safety
Decals section for location drawing.

STORAGE

NOTICE
■

Store the tiller inside when possible. If this is
not possible, store the tiller on a pallet. Be sure the
tiller is stored off the ground to protect the couplers and hoses.

■

The supply and return hoses must always be
secured with quick disconnects or caps to prevent
loss of fluids and contamination.

WARNING
■

Keep children and bystanders away from storage area.

MAN0003 (Rev. 11/30/2006)

TROUBLESHOOTING
PROBLEM
Drum will not rotate

Drum rotates sluggishly

Motor operates, but the drum does
not rotate

Oil is leaking from the motor area.

Insufficient cutting power

MAN0003 (Rev. 11/30/2006)

POSSIBLE CAUSES

SOLUTION

Auxiliary hoses are not hooked up
to skid steer

Inspect connections visually (make
sure QD’s are fully engaged).

There is an obstruction in one or
both of the auxiliary hoses

Remove and inspect hoses
visually.

One or more seals on the motor
have failed

Contact dealer.

Skid steer auxiliary hydraulics are
not operating properly

Refer to skid steer owner’s
manual.

Motor hoses are not plumbed
correctly

See “Hydraulic Assembly TL52” on
page 22. Verify correct hose
routing.

Insufficient hydraulic flow from the
skid steer

Refer to skid steer owner’s
manual.

The hydraulic oil filter on the skid
steer is dirty

Refer to skid steer owner’s
manual.

One or more seals on the motor
have failed

Contact dealer.

Cross bolt on coupler is sheared

Inspect visually and repair as
needed.

Coupler splines are stripped

Inspect visually and repair as
needed.

Motor shaft splines are stripped.

Inspect visually and repair as
needed.

One or more seals on the motor
have failed.

Contact dealer.

O-rings on fitting are damaged

Visually inspect o-rings and
replace as needed.

Fittings are loose or damaged

Refer to skid steer owner’s
manual.

Hydraulic hoses are loose or
damaged

Refer to skid steer owner’s
manual.

One or more seals on motor have
failed

Contact dealer.

Oil filter on the skid steer is dirty

Refer to skid steer owner’s
manual.

Insufficient auxiliary flow from skid
steer

Refer to skid steer owner’s
manual.

Relief valve on skid steer is not set
properly

Refer to skid steer owner’s
manual.

Troubleshooting 13

TROUBLESHOOTING
PROBLEM
Excessive oil temperature

Insufficient tilling power

POSSIBLE CAUSES

SOLUTION

Obstruction in one or both auxiliary
hoses

Visually inspect and replace hoses
as necessary.

Hydraulic oil level on skid steer is
low

Refer to skid steer owner’s
manual.

Hydraulic oil in skid steer is dirty

Refer to skid steer owner’s
manual.

Hydraulic oil filter on skid steer is
dirty

Refer to skid steer owner’s
manual.

Relief valve on skid steer is not set
properly

Refer to skid steer owner’s
manual.

The tines are worn or bent

Replaced damaged tines.

Debris has built up inside the
chassis

Clean debris from inside of
chassis.

Insufficient hydraulic flow from the
skid steer

Refer to skid steer owner’s
manual.

The hydraulic oil filter on the skid
steer is dirty

Refer to skid steer owner’s
manual.

One or more seals on the motor
have failed

Contact dealer.

14 Troubleshooting

MAN0003 (Rev. 11/30/2006)

SERVICE
DRUM REMOVAL
Rotate the tiller so it rests on the attach wings as
shown in Figure 5. Use a hoist to support the drum at
the midpoint.

Figure 7.
Remove the coupler bolt (3) and the coupler (4) from
both sides of the drum as shown in Figure 8.
DP4

Figure 5.
Remove the two depth skid bolts (1) and four motor
housing bolts (2) from one side as shown in Figure 6.

4
2
1

3
Figure 8.

DP5

Figure 6.
Remove the depth skid and the motor housing from
one side as shown in Figure 7. Slide the drum off
remaining motor shaft.

MAN0003 (Rev. 11/30/2006)

MOTOR REMOVAL
Rotate the tiller so it rests on the attach wings as
shown in Figure 9. Use a hoist to support the drum at
the midpoint.

Service 15

Use an extension and a 1/2” twelve point socket to hold
motor bolts from the inside and remove the four 1/2”
nuts (4) from the bottom as shown in Figure 12.

DP4

Figure 9.
4

Remove the two depth skid bolts (1) and four motor
housing bolts (2) from one side as shown in Figure 10.
DP9

Figure 12.

MOTOR INSTALLATION

2
1

Place the motor housing into a vice (1). Install the
motor and orient the motor ports (2) as shown in Figure
13.

DP5

2
Figure 10.
Remove the depth skid and motor housing. Place the
motor housing in vice (3) as shown in Figure 11.
1

DP8

Figure 13.
Install four 1/2” - 20 x 1-1/2” twelve-point bolts (3) and
four 1/2” - 20 (4) nuts as shown in Figure 14 and Figure
16. While using an extension and 1/2” twelve-point
socket, hold bolts from the inside and torque nuts to 85
lbs-ft. (115 N-m).
DP8

Figure 11.

16 Service

MAN0003 (Rev. 11/30/2006)

DRUM INSTALLATION
Rotate the tiller chassis (1) so that it rests on the attach
bracket as shown in Figure 17.

Figure 14. TL52 and TL73
Install motor housing (5) into one side of the chassis
using four 1/2” x 1-1/2” bolts (6), eight 1/2” flat washers
(7) and four 1/2” - 13 nuts (8) as shown in Figure 15.

DP12

Figure 17.
Insert one coupler (2) into each end of the drum as
shown in Figure 18. Make sure the end nearest the
hole is to the inside. Line up the hole in the drum (3)
with the hole in the coupler and install one 1/2" x 3-3/4"
bolt (4) and one 1/2" - 20 nut (5).
Torque to 85 lbs-ft (115 N-m).
6 7

5
5
3
2

DP10

Figure 15.

DP7

Figure 18.
Install the motor housing (6) into one side of the chassis using four 1/2" x 1-1/2" bolts (7), eight 1/2" flat
washers (8) and four 1/2" - 13 nuts (9) as shown in Figure 19. Torque to 120 lbs-ft (163 N-m).

Figure 16. TL84

MAN0003 (Rev. 11/30/2006)

Service 17

7 8

6
17

DP10

Figure 19
Use a hoist to lift the drum. Make sure the coupler is
aligned with the motor shaft and insert motor shaft into
drum as shown in Figure 20.

DP12

Figure 21.
Assemble the depth skid on either side of the chassis,
using an additional two 5/8" washers (18) and two 5/8"
nuts (19) for each side as shown in Figure 22. Torque
to 240 lbs-ft (325 N-m).

DP6

Figure 20.
Install the motor housing into other side of the chassis.
Install the motor housing (6) into one side of the chassis using four 1/2" x 1-1/2" bolts (7), eight 1/2" flat
washers (8) and four 1/2" - 13 nuts (9) as shown in Figure 19. Torque to 120 lbs-ft (163 N-m).
18 19

Note: It may be necessary to rotate drum to allow the
splines on the coupler to align with the splines on the
motor shaft.

DEPTH SKID ASSEMBLY
Install two 5/8" x 4-1/2" bolts (14) and two 5/8" washers
(15) in each depth skid (17) as shown in Figure 21.
Slide the two bushings (16) onto the 5/8" bolts.

DP13

Figure 22.

18 Service

MAN0003 (Rev. 11/30/2006)

TINE REPLACEMENT
To replace worn or broken tines (1), remove the 1/2"
nut (3) and bolt (2) as shown in Figure 23. Remove the
worn or broken tine and replace with a new tine. Install
1/2" x 1-1/2" - 20 bolt (2) and 1/2" - 20 nut (3). Torque to
50 lbs-ft (68 N-m). The tine should rotate ±15° when a
small force is applied to the tine. If the tine does not
rotate, loosen the nut until the tine is free to rotate.
2 3
1

Figure 23.

MAN0003 (Rev. 11/30/2006)

Service 19

DRUM ASSEMBLY

REF

PART

QTY

DESCRIPTION

REF

PART

QTY

DESCRIPTION

59000

24 Bolt, 1/2 NF x 1-1/2 GR8 ZP TL52

101533

24 Tine, TL52

59000

24 Bolt, 1/2 NF x 1-1/2 GR8 ZP TL73

101533

36 Tine, TL73

59000

24 Bolt, 1/2 NF x 1-1/2 GR8 ZP TL84

101533

40 Tine, TL84

105170

Drum weld, 52" TL52

B0816

24 Nut, 1/2 - 20 Stover PLT TL52

101913

Drum weld, 73" TL73

B0816

36 Nut, 1/2 - 20 Stover PLT TL73

102402

Drum weld, 84" TL84

B0816

40 Nut, 1/2 - 20 Stover PLT TL84

20 Parts

(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)

BASE UNIT ASSEMBLY

REF

PART

QTY

DESCRIPTION

REF

PART

QTY

DESCRIPTION

20551

Bolt, 5/8 NC x 4-1/2 GR8 ZP

105899

Drum assembly TL73

21666

Bolt, 1/2 NC x 1-1/2 GR8 ZP

105900

Drum assembly TL84

57816

16 Washer 1/2 SAE flat hrd

105901

Housing/motor asy TL52/TL73

101921

Collar, round bore TL73

S0100111

Seal kit (TL52/TL73 motor)

102993

Skid

105902

Housing/motor asy TL84

104351

Bushing, TL Skid pin

1025864

Seal Kit (TL84 motor)

105715

Attach chassis TL52

B0815

Nut, 1/2 - 13 Stover plt GR5

105784

Attach chassis TL73

B0816

Nut, 1/2 - 20 Stover plt GR5

105786

Attach chassis TL84

B0830

Bolt, 1/2 x 3-3/4 - 20 GR8

B1015

Nut, 5/8 - 11 Stover UNC GR5

B1021

Washer, 5/8 flat SAE plt hrd

(Rev. 7/4/2008)
MAN0003 (Rev. 11/30/2006)

Parts 21

HYDRAULIC ASSEMBLY TL52

CONNECTION

HOSE

END

H1265

-10 ST

H1265

-8 ST

H1264

90°

H1281

90°

PART

QTY

REF
1

105716

F1016

F1020

F1231

HC415

DESCRIPTION

REF

PART

QTY

DESCRIPTION

Tube, 63.39 hyd TL52

Fitting 10 OM x 8 FLM ST

F1140

Fitting 12 OM x 10 FLM ST

Fitting 8 FLF x 8 FLM 90°

H1264

Hose #8 x 19" 8 FLF x 8 FLF 90° R2

8 FLM x 8 FLM x 8 FLM

H1265

Hose #10 x 52" 10 FLF x 8 FLF R2

QD 1/2" F Parker FE501-12 FONL

H1281

Hose #8 x 21" 8 FLF x 8 FLF 90° R2

22 Parts

HC414

QD 1/2" M Parker FE502-12 FO

(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)

HYDRAULIC ASSEMBLY TL73

CONNECTION

HOSE

END

H1280

-10 ST

H1280

-12 ST

H1278

90°

H1279

90°

PART

QTY

REF

DESCRIPTION

REF

PART

QTY

DESCRIPTION

101897

Tube, hyd TL73

F1006

Fitting, 12 OM x 12 FLM

102360

Tube, hyd TL73/TL84

HC414

QD 1/2" M Parker FE502-12FO

F1087

Fitting, 10 OM x 10 FLM ST

HC415

QD 1/2" F Parker FE501-FONL

F1110

Fitting, 10 FLM x 10 FLF 90°

H1278

Hose #10 x 19" 10 FLF x 10 FLF 90°

F1232

Fitting, 10 FLM x 10 FLF x 10 FLM

H1279

Hose #10 x 21" 10 FLF x 10 FLF 90°

H1280

Hose #10 x 21" 10 FLF x 10 FLF 90°

(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)

Parts 23

HYDRAULIC ASSEMBLY TL84

CONNECTION

HOSE

END

H1337

H1335

90°

H1336

90°

PART

QTY

REF

DESCRIPTION

REF

PART

QTY

DESCRIPTION

102746

Tube, hyd TL84

F1006

Fitting, 12 OM x 12 FLM

102747

Tube, hyd TL84

HC415

QD 1/2" F Parker FE501-FONL

F1023

Fitting, 12 FLF x 12 FLM 90°

HC414

QD 1/2" M Parker FE502-12FO

F1077

Fitting, 12 FLM x 12 FLF x 12 FLM

H1335

Hose #12 x 19" 12 FLF x 12 FLF

F1089

Fitting, 12 FLM x 10 OM ST

H1336

Hose #12 x 21" 12 FLF x 12 FLF 90°

H1337

Hose #12 x 84" 12 FLF x 12 FLF

24 Parts

(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)

DECAL PLACEMENT

REF

MAN0003 (Rev. 11/30/2006)

PART

QTY

DESCRIPTION

D0119

Decal, Alitec (white with black)

D0155

Decal, TL52

D0161

Decal, TL73

D0264

Decal, TL84

D0157

Decal, tie down

D0158

Decal, lift point

Parts 25

FITTING TORQUE CHART
Always tighten fittings to these values unless a different torque value is listed
for a specific service procedure.
Make sure fastener threads are clean and threads are engaged properly.
All torque values are adopted from SAE J514 and SAE J1453.

Size

SAE (JIC)
37° Flare Thread
Size

O-Ring Style
Straight Thread
Size

Seal-Lok
Thread

5/16 - 24

---

3/8 - 24

---

7/16 - 20

9/16 - 18

1/2 - 20

---

9/16 - 18

11/16 - 16

3/4 - 16

13/16 - 16

7/8 - 14

1 - 14

1-1/16 - 12

1-3/16 - 12

---

1-5/16 - 12

1-7/16 - 12

1-5/8 - 12

1-11/16 - 12

1-7/8 - 12

2 - 12

2-1/2 - 12

---

TORQUE
SAE
Dash
Size

Lbs-Ft

N-m

Lbs-Ft

N-m

Lbs-Ft

N-m

---

105

143

100

140

190

125

120

184

250

---

100

135

221

300

122

165

133

180

258

350

147

200

166

225

317

430

166

225

236

320

---

SAE 37° Flare

26 Appendix

O-Ring Straight Thread

Seal-Lok

Fitting Torque Chart (7/15/2005)

QUICK COUPLER KITS
High-Flow with Auxiliary

High-Flow with No Auxiliary

Low-Flow

QC Kit

Description

QC Kit

Description

QC Kit

Description

Bobcat

HC356

Flush Face

HC355

Flush Face

HC357

Flush Face

HC243

Poppet

HC211

Ag Ball Valve

HC279

Flush Face

HC211

Ag Ball Valve

Vintage

Make

1013825

Flush Face

HC278

Flush Face

HC209

Flush Face &
Ag Ball Valve

Cat

HC538

Flush Face

1014196

Flush Face

1014197

Flush Face

Daewoo

HC209

Flush Face

HC212

Flush Face

HC211

Ag Ball Valve

Gehl

HC398

Flush Face

1014195

Flush Face

HC400

Flush Face

HC305

Poppet &
Ag Ball

Vintage

Case

HC212

Flush Face

John Deere

1014198

Flush Face

1013826

Flush Face

HC310

Flush Face

Komatsu

1013834

Flush Face

1013833

Flush Face

1013835

Flush Face

New Holland

1014199

Flush Face

HC308

Flush Face

HC310

Flush Face

Scat Trak

HC537

Flush Face

HC243

Poppet

QUICK COUPLER KIT COMPONENTS
QC KIT

Includes

Style

Male/Female

Body
Size

Hose End

HC193

Flush Face

Male

3/4

SAE #12 O-ring

HC194

Flush Face

Female

3/4

SAE #12 O-ring

HC195

Ag Ball

Female

1/2

1/2-14 NPT

HC196

Ag Ball

Male

1/2

1/2-14 NPT

HC197

Flush Face

Female

1/2

SAE #10 O-ring

HC211

HC195

Ag Ball

Female

1/2

1/2-14 NPT

HC196

Ag Ball

Male

1/2

1/2-14 NPT

HC212

HC193

Flush Face

Male

3/4

SAE #12 O-ring

HC194

Flush Face

Female

3/4

SAE #12 O-ring

HC197

Flush Face

Female

1/2

SAE #10 O-ring

HC193

Flush Face

Male

3/4

SAE #12 O-ring

HC194

Flush Face

Female

3/4

SAE #12 O-ring

HC197

Flush Face

Female

1/2

SAE #10 O-ring

HC201

Flush Face

Male

1/2

SAE #10 O-ring

HC197

Flush Face

Female

1/2

SAE #10 O-ring

HC201

Flush Face

Male

1/2

SAE #10 O-ring

HC209

HC278

HC279

Quick Coupler Chart (Rev. 10/20/2006)

Quick Coupler 27

QUICK COUPLER KIT COMPONENTS
QC KIT

Includes

Style

Male/Female

Body
Size

Hose End

HC416

Flush Face

Female

5/8

SAE #12 O-ring

HC417

Flush Face

Male

5/8

SAE #12 O-ring

HC418

Flush Face

Male

3/8

SAE #8 O-ring

HC310

HC414

Flush Face

Male

1/2

SAE #12 O-ring

HC415

Flush Face

Female

1/2

SAE #12 O-ring

HC355

HC344

Flush Face

Male

12 mm

SAE #12 O-ring

HC345

Flush Face

Female

12 mm

SAE #12 O-ring

HC346

Flush Face

Female

9 mm

SAE #8 O-ring

HC342

Flush Face

Female

7 mm

SAE #6 O-ring

HC343

Flush Face

Male

7 mm

SAE #6 O-ring

HC344

Flush Face

Male

12 mm

SAE #12 O-ring

HC345

Flush Face

Female

12 mm

SAE #12 O-ring

HC308

HC356

HC357
HC398

HC400
HC537

HC538

1013825

1013826

1013833

HC346

Flush Face

Female

9 mm

SAE #8 O-ring

HC344

Flush Face

Male

12 mm

SAE #12 O-ring

HC345

Flush Face

Female

12 mm

SAE #12 O-ring

HC344

Flush Face

Male

12 mm

SAE #12 O-ring

HC345

Flush Face

Female

12 mm

SAE #12 O-ring

HC346

Flush Face

Female

9 mm

SAE #8 O-ring

HC344

Flush Face

Male

12 mm

SAE #12 O-ring

HC345

Flush Face

Female

12 mm

SAE #12 O-ring

HC415

Flush Face

Female

1/2

SAE #12 O-ring

HC416

Flush Face

Female

5/8

SAE #12 O-ring

HC417

Flush Face

Male

5/8

SAE #12 O-ring

HC418

Flush Face

Male

3/8

SAE #8 O-ring

HC521

Flush Face

Female

16 mm

SAE #12 O-ring

HC522

Flush Face

Male

16 mm

SAE #12 O-ring

1532994

Flush Face

Female

3/4

SAE #12 O-ring

1532995

Flush Face

Male

3/4

SAE #12 O-ring

1532997

Flush Face

Female

1/2

SAE #8 O-ring

HC417

Flush Face

Male

5/8

SAE #12 O-ring

HC418

Flush Face

Male

3/8

SAE #8 O-ring

HC545

Flush Face

Female

5/8

SAE #12 O-ring

HC546

Flush Face

Female

1/2

SAE #10 O-ring

HC547

Flush Face

Male

1/2

SAE #10 O-ring

HC343

Flush Face

Male

7 mm

SAE #6 O-ring

HC521

Flush Face

Female

16 mm

SAE #12 O-ring

HC522

Flush Face

Male

16 mm

SAE #12 O-ring

HC415

Flush Face

Female

1/2

SAE #12 O-ring

HC521

Flush Face

Female

16 mm

SAE #12 O-ring

HC522

Flush Face

Male

16 mm

SAE #12 O-ring

28 Quick Coupler

Quick Coupler Chart (Rev. 10/20/2006)

QUICK COUPLER KIT COMPONENTS
QC KIT

Includes

Style

Male/Female

Body
Size

Hose End

HC414

Flush Face

Male

1/2

SAE #12 O-ring

HC415

Flush Face

Female

1/2

SAE #12 O-ring

HC521

Flush Face

Female

16 mm

SAE #12 O-ring

HC522

Flush Face

Male

16 mm

SAE #12 O-ring

1013835

46058

Flush Face

M/F Set

3/4

SAE #12 O-ring

1014195

HC344

Flush Face

Male

12 mm

SAE #12 O-ring

HC345

Flush Face

Female

12 mm

SAE #12 O-ring

HC346

Flush Face

Female

9 mm

SAE #8 O-ring

HC521

Flush Face

Female

16 mm

SAE #12 O-ring

HC522

Flush Face

Male

16 mm

SAE #12 O-ring

1532997

Flush Face

Female

1/2

SAE #8 O-ring

1532994

Flush Face

Female

3/4

SAE #10 O-ring

1532995

Flush Face

Male

3/4

SAE #10 O-ring

HC343

Flush Face

Male

7 mm

SAE #6 O-ring

HC414

Flush Face

Male

1/2

SAE #12 O-ring

HC415

Flush Face

Female

1/2

SAE #12 O-ring

HC521

Flush Face

Female

16 mm

SAE #12 O-ring

HC522

Flush Face

Male

16 mm

SAE #12 O-ring

HC414

Flush Face

Male

1/2

SAE #12 O-ring

HC415

Flush Face

Female

1/2

SAE #12 O-ring

HC416

Flush Face

Female

5/8

SAE #12 O-ring

HC417

Flush Face

Male

5/8

SAE #12 O-ring

HC418

Flush Face

Male

3/8

SAE #8 O-ring

1013834

1014196

1014197
1014198

1014199

Quick Coupler Chart (Rev. 10/20/2006)

Quick Coupler 29

BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification

SAE SERIES
TORQUE
CHART

SAE Grade 2
(No Dashes)

SAE Grade 8
(6 Radial Dashes)

SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD

SAE 2

SAE 5

SAE 8

Diameter
(Inches)

Wrench
Size

lbs-ft

N-m

lbs-ft

N-m

lbs-ft

N-m

1/4"
5/16"

7/16"
1/2"

6
12

8
17

10
19

13
26

14
27

18
37

3/8"
7/16"

9/16"
5/8"

23
36

31
48

35
55

47
75

49
78

67
106

1/2"
9/16"

3/4"
13/16"

55
78

75
106

85
121

115
164

120
171

163
232

5/8"
3/4"

15/16"
1-1/8"

110
192

149
261

170
297

230
403

240
420

325
569

7/8"
1"

1-5/16"
1-1/2"

306
467

416
634

474
722

642
979

669
1020

907
1383

METRIC SERIES
TORQUE
CHART

Metric Bolt Head
Identification

8.8
Metric
Grade 8.8

10.9
Metric
Grade 10.9

COARSE THREAD

FINE THREAD

MARKING ON HEAD

Diameter &
Thread Pitch
(Millimeters)

Wrench
Size

N-m

lbs-ft

N-m

lbs-ft

N-m

lbs-ft

N-m

lbs-ft

Diameter &
Thread Pitch
(Millimeters)

6 x 1.0

10 mm

6 x 1.0

8 x 1.25
10 x 1.5

13 mm
16 mm

20
39

15
29

27
54

20
40

21
41

16
30

29
57

22
42

8 x 1.0
10 x 1.25

12 x 1.75
14 x 2.0

18 mm
21 mm

68
109

50
80

94
151

70
111

75
118

55
87

103
163

76
120

12 x 1.25
14 x 1.5

16 x 2.0
18 x 2.5

24 mm
27 mm

169
234

125
172

234
323

173
239

181
263

133
194

250
363

184
268

16 x 1.5
18 x 1.5

20 x 2.5
22 x 2.5

30 mm
34 mm

330
451

244
332

457
623

337
460

367
495

270
365

507
684

374
505

20 x 1.5
22 x 1.5

24 x 3.0
30 x 3.0

36 mm
46 mm

571
1175

421
867

790
1626

583
1199

623
1258

459
928

861
1740

635
1283

24 x 2.0
30 x 2.0

Typical Washer
Installations
Bolt

Metric 8.8

Lock Washer

Metric 10.9

Metric 8.8

Metric 10.9

Flat Washer

8/9/00

30 Appendix

Bolt Torque & Size Charts (Rev. 3/28/2007)

BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

SAE Bolt Thread Sizes
5/16
3/8
1/2

5/8

3/4

7/8

100

125

150

175

Metric Bolt Thread Sizes
8MM
10MM

12MM

14MM

16MM

18MM

ABBREVIATIONS
AG .............................................................. Agriculture
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................ British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT ........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH .................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................ Millimeter
M.......................................................................... Male

Bolt Torque & Size Charts (Rev. 3/28/2007)

MPa......................................................... Mega Pascal
N.......................................................................Newton
NC ...................................................... National Coarse
NF ...........................................................National Fine
NPSM..................... National Pipe Straight Mechanical
NPT .......................................... National Pipe Tapered
NPT SWF ......... National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY ...................................................... Power-Beyond
psi.......................................... Pounds per Square Inch
PTO ..................................................... Power Take Off
QD ....................................................Quick Disconnect
RH ..............................................................Right Hand
ROPS ........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE ..........................Society of Automotive Engineers
UNC ..................................................... Unified Coarse
UNF...........................................................Unified Fine
UNS...................................................... Unified Special

Appendix 31

WARRANTY
(All Models Except Mow’n Machine

Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)

Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________

From (Dealer): ___________________________________________

Model Number: ____________________________

Serial Number: ___________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted

Model Number
BW1260, BW1800

Duration (from date of delivery
to the original purchaser)
8 years

BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X,
6 years
BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3
Gearbox
components

PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2, 5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
RDC54, RD60, RD72

3 years (1 year if used in rental or
commercial applications)

Blade spindles

RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,
3 years
9180RD-2, 9204RD-2

Rust-through

BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW180-3,
10 years
BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:

F-3079 (Rev. 5/15/2008)

WARRANTY
(Replacement Parts For All Models Except Mow’n MachineTM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:

F-8494 (Rev. 6/23/2005)

PART NO.

MAN0003

Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
www.WoodsEquipment.com
© 2002 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:07:03 08:37:36-05:00
Create Date                     : 2008:07:02 11:27:31-05:00
Metadata Date                   : 2008:07:03 08:37:36-05:00
Format                          : application/pdf
Title                           : Alitec Tiller TL52, TL73, TL84
Creator                         : MAN0003 (Rev. 7/4/2008)
Description                     : RJM
Subject                         : Added two seal kit numbers to the Base Unit Assembly parts list on page 21. S010011 and 1025864.
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Keywords                        : Added two seal kit numbers to the Base Unit Assembly parts list on page 21. S010011 and 1025864.
Document ID                     : uuid:c3642d19-ea0c-4556-a3e8-56354765020c
Instance ID                     : uuid:c5c5072d-f7ca-4701-b530-495dcc7cc7b8
Page Count                      : 34
Author                          : MAN0003 (Rev. 7/4/2008)

EXIF Metadata provided by EXIF.tools

Woods Equipment Tl52 Users Manual Alitec Tiller TL52, TL73, TL84

TL52 to the manual 3ed750de-a001-44a4-9792-a91885811415

Navigation menu

Versions of this User Manual:

Views

Navigation