WowWee Group 0223 27 MHz Remote Control TX User Manual pro2

WowWee Group Limited 27 MHz Remote Control TX pro2

Contents

users manual 2

NG
0223
US
01
Manufactured and Distributed by:
© 2002 WowWee
All rights reserved.
WowWee (Asia Office)
Unit 301A-C, 92 Granville Rd.,
T.S.T. East, Kowloon, H.K.
WowWee (North America Office)
4480 Cote de Liesse, Suite 320,
T.M.R. Quebec, H4N 2R1, Canada
Consumer Hotline: (514) 344-1250
http://www.wowwee.com
Printed in China
Manufactured and Distributed by:
© 2002 WowWee
All rights reserved.
WowWee (Asia Office)
Unit 301A-C, 92 Granville Rd.,
T.S.T. East, Kowloon, H.K.
WowWee (North America Office)
4480 Cote de Liesse, Suite 320,
T.M.R. Quebec, H4N 2R1, Canada
Consumer Hotline: (514) 344-1250
http://www.wowwee.com
Printed in China
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful
interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect one equipment into an outlet on a circuit different from that to which the receiver is needed.
• Consult the dealer or an experienced radio / TV technician for help.
ATTENTION !!! IMPORTANT BATTERY INFORMATION
Use only fresh batteries of the required size and recommended type. Do not mix old and new batteries, different types of batteries (standard alkaline, or rechargeable), or
rechargeable batteries of different capacities. We suggest the use of alkaline batteries for best results.
Please respect the correct polarity + and –
Do not try to recharge batteries, nor to open them.
Do not throw batteries into the fire.
Remove rechargeable batteries from the toy before being charged.
Rechargeable batteries are only to be charged under adult supervision.
Use only the battery types as recommended.
Replace all batteries of same type/brand at the same time.
Do not short-circuit the battery contacts.
Remove exhausted batteries from the toy.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Transmitter
Bottom of Pro-Kart Racer
ON
OFF
ON
OFF
See how fast you can change all of the spare parts - the tires, spoiler and bumper!
Use a phillips screw driver to change the tires. For the nose cone, gently remove the
front bumper then replace the nose cone. Spoiler: gently remove and replace.
REPLACE YOUR PARTS
Nose Cone
spoiler
tire
bumper
Note:
•Quality of control function 
may deteriorate when  
battery power is low.
BATTERY INSTALLATION
•Remove the battery compartment 
cover using a screwdriver as shown.
•Insert correct battery - as shown in 
diagram, making sure to match the 
polarity direction.
•Replace the battery cover.
STUNTS
bumper
Transmitter Antenna
Screw-in to the base
Spare Nose Cone
Spare Spoiler
1. For super fast 360˚ spins, turn the
wheel all the way to the right or left,
while the trigger is fully pulled.
2. Do a reverse 180˚! Drive in reverse,
then spin the racer around 180˚ and
drive forward! Drive like a PRO for this
stunt!
BATTERY AND POWER
ON/OFF DIAGRAM
APPLYING DECALS
- Apply the decals as shown,
in orderly sequence from 1

Navigation menu