XAC Automation AP10 PINPAD User Manual

XAC Automation Corporation PINPAD

UserManual.wiki >

XAC Automation >

AP10 User Manual HTML Version

User Manual

d





ALLATI

PAYME

UID

T DEVICE

1. PACKAGE CONTENT

2. DEVICE OVERVIEW



xCL_AP‐10(hereundercalledAP‐10)KeyButtons&InterfacePorts(Figure1):

Figure1

FRONTAREA1 4” TFT Color Display (480 x 800 pixel)

2 Rubber Keypad

3 Smart Card Reader (SCR) slot

4 Magnetic Strip Reader (MSR) slot

REARAREA5 USB cable (type A)

6 SAM Compartment

■ AP-10 power spec:

z PowerInput:5VDC,2A

z OperatingTemperature:0oCto40oC



FRONTREAR

 xCL_AP-10  Privacy Shield (Optional)

OWE



Topowe

terminal

Note:Af

SING



Swipeth

display.(

NING:

1.Theequipmenti

trainingorexperie

energiesandenergy

2.Theequipmentis

portthatthatoutp

60950‐1/EN60590

‐

aution:UseonlytheA

withthisdevice

ution:Riskofexplosi

batteryaccordin

FF THE

ronthedevice,ple

orPOS.

erbootingupAP‐10,

ersavingmode.Ple

AGNETIC

ecardthroughthe

Figure2)

intendedtobeinstall

ceintheequipment

magnitudesusedinth

intendedtobesupplie

tcomplieswithther

‐

1/UL60590‐1/CSA6

adapterapprovedand

nifthebatteryisrepl

totheinstructions.

EVICE

aseplugtheUSBc

isnoactiononAP

‐

seshortpressanyb

ARD

EADE

lotwithmagnetics

Figure2

edbyskilledpersono

technology,particularl

equipmentandhostd

byahostdevice(PC

quirementoftheLim

950‐1

providedbyXACAuto

cedbyanincorrectty

bletypeAintothe

‐

10after60seconds,

uttononkeypadto

tripesidefacingth

servicepersonwhoh

yinknowingthevari

vice.

rterminaldevice)via

itedPowerSourceof

ationCorporationfor

e.Pleasedisposeofu

USBportofyourh

thedevicewillenter

akeupthedevice.

samedirectionas

ve

us

SB

IEC

se

ed

st

he

5. USING THE IC CARD READER



InsertanICcardintotheslot(Figure3)withthechipsidefacingupwardasthedisplay(Figure

4).



Figure3Figure4



6. USING THE KEY PAD



Afterinsertingthechipcard,Pressthenumerickeyasbelowkeypad(Figure5)toenterthe

desirablenumbers.PressCancel(X)keytoterminateanycurrentoperationorpresstheEnter

(O)keytoconfirmavalueoranoption.

Figure5

7. USING THE CONTACTLESS CARD READER



Tapthecontactlesscardontopofthecontactlesslogo(Figure6).



Figure6

9. INSERT SIM & SAM CARD

ToremovetheSAMcardcompartmentbyunlockingthescrewM1.6*3pieces,pleaseusethe

screwdrivertype0(Figure7),

Afterremovingthecover,theusercanfindSAM*2slotsatthebottomsideofdevice.Please

insertthecardcorrectlyastheiconshownonthecover(Figure8):



Figure7Figure8

Caution:Whenremovingrearcover(Figure7)forthepurposesofSAMcardinstallation,rememberto

reinstallationtheprotectivecoverandmakesuretokeepitinplaceduringnormaloperation.

9. INSTALL PRIVACY SHIELD (OPTIONAL ACCESSORY)

PleaserefertoFigure9for2stepstoinstalltheshield:

Step1:AlignandinserttwohooksofprivacyshieldwiththeslotonAP‐10device(filledby

rubber).

Step2:Pushdownthebottomsideofshieldtocombinewiththedevice.Andtheoutlook

isthesameasFigure10.

Figure9Figure10

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RadiationExposureStatement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and

are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved

if the product can be kept as far as possible from the user body or set the device to lower output power if such

function is available.





The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be

disclosed, distributed or reproduced without permission of XAC Automation Corporation.

XAC Automation Corporation

886-3-577-2738

XAC Automation AP10 PINPAD User Manual

XAC Automation Corporation PINPAD

User Manual

Navigation menu

Namespaces

Views

Navigation