XAC Automation FD35GT PINPAD User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2037411
Application ID	VgqvvqeDMl0P8SM02KK3lg==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.28kB (65990 bits)
Date Submitted	2013-08-08 00:00:00
Date Available	2013-08-08 00:00:00
Creation Date	2013-07-30 13:39:04
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2013-08-05 17:24:19
Document Title	untitled

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Warning: If the device, FD-35GT, is used without the detachable privacy shield, the following
criteria needs to be met by the Installed Environment of the PED for complying with the PCI
privacy screen design requirement:
A. Positioning of the PED on the check-stand in such way as to make visual observation of the
PIN-entry process infeasible.
„
Visual shields designed into the check-stand.
„
Position the PED so that it is angled in such a way to make PIN spying difficult.
B. Pop-up (temporary) privacy shield attached to the PED mounting stand. Consumer
(through education & prompting) or merchant would put the shield in place during PIN
entry.
C. Installing PED on an adjustable stand that allows consumers to swivel the terminal
sideways and/or tilt it forwards/backwards to a position that makes visual observation of
the PIN-entry process difficult.
D. Positioning of in-store security cameras such that the PIN-entry keypad is not visible.
Instructing the cardholder regarding safe PIN-entry, done with a combination of:
„
Signage on the PED.
„
Prompts on the display, possibly with a "click-through" screen.
„
Potentially literature at the point of sale.
„
A logo for safe PIN-entry process.
Table A1: Matrix of Observation Corridors and PIN Protection Method
Observation Corridors
Customers
Customers
On-Site
Remote
Method
Cashier
in Queue
Elsewhere
Cameras
Cameras
PED Stand A
PED Stand B
Check-Stand A
Check-Stand B
Customer Instruction
H*
H*
H*
H*
H*
Customer Instruction methods are less repeatable and therefore should be used in combination with other
methods. L = low, M = medium, H = high.
XAC Automation Corporation
886-3-577-2738
www.xac.com.tw
The above information is the exclusive intellectual property of XAC Automation Corporation
and shall not be disclosed, distributed or reproduced without permission of XAC Automation
Corporation.
XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or
errors made herein; nor for incidental or consequential damages resulting from the furnishing,
performance or use of his material.
This document contains proprietary information protected by copyright. All rights are reserve.
PIN PAD
FD-35GT
INSTALLATION GUIDE
1. CONNECTING THE FD-35GT PIN PAD
The FD-35GT device can be used to connect with PC/terminal. It
supports USB interfaces (Figure 1) type connector.
Note: Turn off or unplug the terminal/PC whenever you connect
or disconnect the PIN Pad. Be sure the terminal/PC is not
processing data when powering down.
Plug the USB connector of FD-35GT to the USB port at the top end
of a PC.
„ PIN pad Input voltage: 5Vdc / 500mA (USB)
„ Operating Temperature: 0ºC ~ 40 ºC
„ RTC battery: 3V, CR2032
Caution: Risk of explosion if the battery is replaced by an incorrect
type. Please dispose of used battery according to the instructions.
Caution: The cover(Figure2) shall be provided with a means to
keep it closed during normal operation.
7. CLEANING
Periodically clean the PIN Pad device with a clean cloth dampened with water and
a mild soap or cleaner. Do not use harsh chemicals.
Figure 1
If you need to return your PIN Pad device for service or replacement, contact your
service provider or sales representative for instructions.
Note: Do not try to service, repair or adjust the PIN Pad device in any other way;
doing so will void your warranty.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
Figure 2
2. MAGNETIC STRIPE READER
Find the card reader slot at the right side of PIN Pad.
Slide the card in either direction through the slot without stopping.
If the card swipe fails, check the position of the magnetic stripe and
slide the card again. (Figure 3)
Figure 3
3. USING THE CARD READER
Find the card reader slot on bottom of PIN Pad. Please insert the
card completely and make sure that it cannot be moved forward
anymore. If inserted failed, check the position of the card and insert
the card again. (Figure 4)
Figure 4
4. USING THE PINPAD
Press numeral key to enter password if needed. Then press green
[ENTER] key to finish password key-in. Press red [CANCEL] key
to exit from presently status (Figure 5). If the PIN is entered
incorrectly, press yellow key and reenter it.
Figure 5
5. CONTACTLESS READER
Contactless reader is on the top of FD-35GT. It will light up with
blue color signal when FD-35GT is powered on and that means
reader is working normally.
Put contactless card to approach the signal icon in the middle area
of card reader (Figure 6) for reading the card data during
transaction.
8. RETURNING THE PIN PAD DEVICE
Figure 6
6. INSTALLING THE PRIVACY SHIELD
The privacy shield is installed on the device, and the keypad will be
separated from the LCD. (Figure 7)
Figure 7
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif
ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage
reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2013:07:30 13:39:04+08:00
Modify Date                     : 2013:08:05 17:24:19+08:00
Metadata Date                   : 2013:08:05 17:24:19+08:00
Document ID                     : uuid:8f92aa47-9a23-4069-a8db-c4fa30db332f
Instance ID                     : uuid:76c0468c-884d-434a-af49-b5e237150524
Format                          : application/pdf
Title                           : untitled
Page Count                      : 2

EXIF Metadata provided by EXIF.tools