XAVi Technologies X5671 VDSL2/ADSL2+ Router User Manual X5671

XAVi Technologies Corp. VDSL2/ADSL2+ Router X5671

User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1006462
Application ID	WsMLBScpT4v3TemrLfprew==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	211kB (2637453 bits)
Date Submitted	2008-09-25 00:00:00
Date Available	2008-09-25 00:00:00
Creation Date	2008-01-29 12:10:55
Producing Software	pdfFactory v1.57 (Windows XP Chinese)
Document Lastmod	2008-09-25 15:20:57
Document Title	X5671 User manual
Document Creator	pdfFactory http://www.pdffactory.com
Document Author:	shirley

VDSL2/ADSL2+ router with
4-Port Ethernet Switch and
802.11b/g wireless AP
Issue 1.0
th
3 Jan. 2008
X5671 User’s Guide
XAVi Technologies Corporation
Tel: +886-2-2995-7953
9F, No. 129, Hsing Te Road, Sanchung City,
Taipei County 241,
Taiwan
Copyright © 2008, XAVi Technologies Corporation
Information in this manual is subject to change without notice. No part of this manual may be reproduced
or transmitted in any form or by any means, electronic or mechanical, including photocopying or scanning,
for any purpose, without the written permission of XAVi Technologies Corporation.
XAVi Technologies Corporation provides this documentation without warranty of any kind, implied or
expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular
purpose.
II
X5671 User’s Guide
Introduction ................................................................................................... 1
Features ................................................................................................................................ 1
Device Requirements ...........................................................................................................2
Getting to know the device ......................................................................... 3
Parts Check........................................................................................................................... 3
X5671 Front Panel................................................................................................................4
X5671 Rear Panel ................................................................................................................5
Connecting your device .............................................................................. 6
Connecting the Hardware.....................................................................................................6
Step 1. Connect the WAN port to VDSL2 network ..........................................................................7
Step 2. Connect the Ethernet cable .................................................................................................7
Step 3. Attach the power connector .................................................................................................7
Step 4. Configure your Ethernet PCs ...............................................................................................7
Or, step 5. Install a Wireless card and connect Wireless PCs if the device is with wireless
interface..............................................................................................................................................7
Next step ............................................................................................................................................7
Getting Start with the Web pages .............................................................. 8
Accessing the Web pages....................................................................................................8
Commonly used buttons.....................................................................................................10
Testing your Setup..............................................................................................................11
Default device settings........................................................................................................11
Device Information ..................................................................................... 13
Summary.............................................................................................................................13
WAN ....................................................................................................................................13
Statistic ................................................................................................................................ 14
Route...................................................................................................................................16
ARP .....................................................................................................................................16
Advanced Setup ......................................................................................... 17
WAN ....................................................................................................................................17
PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) ..........................................................19
MAC Encapsulation Routing (MER)...............................................................................................21
IP over ATM (IPoA) .........................................................................................................................22
Bridging ............................................................................................................................................23
LAN......................................................................................................................................24
NAT (Network Access Translation) ....................................................................................25
Virtual Server ...................................................................................................................................25
Port Triggering .................................................................................................................................26
III
X5671 User’s Guide
DMZ..................................................................................................................................................27
ALG ..................................................................................................................................................28
Security ...............................................................................................................................28
IP Address Filter ..............................................................................................................................28
MAC Filtering ...................................................................................................................................31
Parental Control...............................................................................................................................32
Routing ................................................................................................................................ 33
Default Gateway ..............................................................................................................................33
Static Route .....................................................................................................................................34
RIP....................................................................................................................................................34
DNS.....................................................................................................................................35
DNS Server......................................................................................................................................35
Dynamic DNS ..................................................................................................................................35
DSL......................................................................................................................................36
Port Mapping.......................................................................................................................37
Wireless Setup ............................................................................................ 39
Basic....................................................................................................................................39
Security ...............................................................................................................................40
MAC Filter ...........................................................................................................................43
Wireless Bridge...................................................................................................................44
Advanced ............................................................................................................................44
Quality of Service................................................................................................................45
Station Information..............................................................................................................46
Diagnostic.................................................................................................... 47
Diagnostic............................................................................................................................47
Management................................................................................................ 48
Settings ...............................................................................................................................48
Backup .............................................................................................................................................48
Update..............................................................................................................................................48
Restore Default................................................................................................................................49
System Log .........................................................................................................................49
TR-069 Client ......................................................................................................................50
Internet Time .......................................................................................................................51
Access Control....................................................................................................................51
Service .............................................................................................................................................51
IP Address........................................................................................................................................52
Password .........................................................................................................................................52
Update Software .................................................................................................................54
Save / Reboot .....................................................................................................................54
Appendix A - Configuring the Internet Settings ................................................ 55
Configuring Ethernet PCs...................................................................................................55
IV
X5671 User’s Guide
Before you begin .............................................................................................................................55
Windows® XP PCs .........................................................................................................................55
Windows 2000 PCs.........................................................................................................................55
Windows Me PCs ............................................................................................................................56
Windows 95, 98 PCs.......................................................................................................................56
Windows NT 4.0 workstations ........................................................................................................57
Assigning static Internet information to your PCs ..........................................................................58
Configuring Wireless PCs...................................................................................................59
Positioning the wireless PCs...........................................................................................................59
Wireless PC cards and drivers .......................................................................................................59
Configuring PC access to your Wireless device ............................................................................59
Appendix B - Troubleshooting............................................................................. 60
Troubleshooting Suggestions.............................................................................................60
Diagnosing Problem using IP Utilities ................................................................................61
Ping ..................................................................................................................................................61
Nslookup ..........................................................................................................................................62
Appendix C – Glossary ......................................................................................... 63
Appendix D - Specification ................................................................................... 70
Appendix E - Warranties ....................................................................................... 72
Appendix F - Regulation ....................................................................................... 74
Appendix G - Contact information....................................................................... 77
X5671 User’s Guide
Congratulations on becoming the owner of the X5671, VDSL2 with 4 Ethernet ports
switch and 802.11g wireless gateway. You will now be able to access the Internet
using your high-speed connection.
The X5671 is a gateway integrating VDSL2, 4 Ethernet ports switch and 802.11g
wireless interfaces into one device which provides the most flexibility and efficiency
way to you. You could connect devices like PCs, Set-Top-Box, ATA, servers, phone
and so on easily by Ethernet and wireless interfaces to enjoy data, voice, and video
services immediately through high speed connection.
This User Guide will show you how to connect your X5671 gateway and how to
customize its configuration to get the most out of your new product.
Features
The list below contains the main features of the device (X5671) and may be useful to
users with knowledge of networking protocols. The chapters throughout this guide will
provide you with enough information to get the most out of your device.
The features include:
Ethernet interface automatic speed-sensing and crossover correction supports
up to 100 Mbps downstream and 100 Mbps upstream rates
Integrated four-port 10/100BaseTX Ethernet switch with speed-sensing and
crossover detection automatically
802.11b/g WLAN supports up to 54 Mbps transmission rate
Provides wireless secure transmitting encryption by either 802.1x; WEP; WEP2;
WPA; WPA2; TKIP; AES
Support Networking protocols such as PPP, Routing , RIP and so on
Support DHCP client and server for IP management
Support Port Forwarding (virtual server) and MAC address filtering
Network address translation (NAT) functions to provide security for your LAN and
multiple PCs surfing Internet simultaneously.
Configuration and management by Web-browser through the Ethernet interface
and remotely through WAN interface
Firmware Supports TR-069
Upgradeable through HTTP (web browser)
X5671 User’s Guide
Device Requirements
In order to use the X5671, you must have the following:
High speed broadband service
Instructions from your ISP on what type of Internet access you will be using, and
the IP addresses needed to set up access
One or more computers, each containing an Ethernet card (10Base-T/100Base-T
network interface card (NIC)).
For system configuration using the supplied web-based program: a web browser
such as Internet Explorer v4 or later, or Netscape v4 or later. Note that version 4
of each browser is the minimum version requirement – for optimum display
quality, use Internet Explorer v5, or Netscape v6.1
Note
You do not need to use a hub or switch in order to connect more than one
Ethernet PC to the device. Instead, you can connect up to four Ethernet
PCs directly to the device using the ports labeled LAN1 to LAN4 on the
rear panel.
X5671 User’s Guide
Parts Check
In addition to this document, your package should arrive containing the following:
The device (X5671)
Ethernet cable
Standard phone line cable
Power adapter
One of X5671 devices
RJ-45 Cable
RJ-11 Cable
Power adapter
Figure 1: X5671 Package Contents
X5671 User’s Guide
X5671 Front Panel
The front panel of this X5671 will be described here which cover all front panel
definitions of other models.
Figure 2: X5671 Front Panel and LEDs
Connector and LED definitions from left to right:
Label
Color
Power
Green
or Red
DSL
Green /
Yellow
Internet
Green
or Red
Function
GREEN off : No power
GREEN on : Power on
RED on : Self-test fails
On : Physical layer sync up successfully.
Off : No connection or no signal
Blink : Physical sync up progress
GREEN off : No connection to Internet
GREEN on : The device gets an IP address
successfully in router mode
GREEN blinking : Data being transmitted.
RED on : PPP Authenication of the device failed. Or it can
not get an IP address in ROUTER mode.
Ethernet
Green
On : LAN link established and active
Off : No LAN link
Blink : Data being transmitted
WLAN
Green
On : WLAN service is enabled
Off : WLAN service is disabled
Blink : Data being transmitted
X5671 User’s Guide
X5671 Rear Panel
The rear panel of this X5671 will be described here which cover all rear panel
definitions of other models.
Figure 3: X5671 Rear Panel Connections
Connector definition:
Label
Function
Antenna
Connects to the 802.11b/11g enabled wireless devices in LAN
Power Switch
ON/OFF switch
Power Jack
Connects to the supplied power adapter
LAN1 ~ LAN4
Connects the device via Ethernet to your devices in LAN
Reset
A reset button to reset the device or reset to default settings
DSL Jack
Connects to the VDSL2 network
X5671 User’s Guide
This chapter provides basic instructions for connecting the device to a computer or
LAN and to the Internet.
In addition to configuring the device, you need to configure the Internet properties of
your computer(s). For more details, see the following sections in Appendix A:
Configuring Ethernet PCs section
Configuring Wireless PCs section
This chapter assumes that you have already subscribed a broadband service with
your Internet service provider (ISP). These instructions provide a basic configuration
that should be compatible with your home or small office network setup. Refer to the
subsequent chapters for additional configuration instructions.
Connecting the Hardware
This section describes how to connect the device to the power outlet and your
computer(s) or network.
Before you begin, turn the power off for all devices. These include
your computer(s), your LAN hub/switch (if applicable), and the device.
WARNING
The diagram below illustrates the hardware connections. The layout of the ports on
your device may vary from the layout shown. Refer to the steps that follow for specific
instructions.
Figure 4: Overview of Hardware Connections for X5671
X5671 User’s Guide
Step 1. Connect the WAN port to VDSL2 network
Connect the WAN port to the VDSL2 network which has the high speed internet
connection.
Step 2. Connect the Ethernet cable
Connect up to four single Ethernet computers or to a HUB/Switch directly to the
device via Ethernet cable(s).
Note that the cables do not need to be crossover cables, the switch provides MDI and
MDIX auto-detection.
Step 3. Attach the power connector
Connect the AC power adapter to the Power connector on the back of the device and
plug the adapter into a wall outlet or power strip. Turn on and boot up your computer(s)
and any LAN devices such as hubs or switches.
Step 4. Configure your Ethernet PCs
You must also configure the Internet properties on your Ethernet PCs. See
Configuring Ethernet PCs section.
Or, step 5. Install a Wireless card and connect Wireless PCs if the device is with
wireless interface
You can attach a Wireless LAN that enables Wireless PCs to access the Internet via
the device.
You must configure your Wireless computer(s) in order to access your device. For
complete instructions, see Configuring Wireless PCs section.
Next step
After setting up and configuring the device and PCs, you can log on to the device by
following the instructions in “Getting Started with the Web pages” on chapter 4. The
chapter includes a section called Testing your Setup, which enables you to verify that
the device is working properly.
X5671 User’s Guide
The device includes a series of Web pages that provide an interface to the software
installed on the device. It enables you to configure the device settings to meet the
needs of your network. You can access it through a web browser on a PC connected
to the device.
Accessing the Web pages
To access the web pages, you need the following:
A laptop or PC connected to the LAN or WLAN port on the device.
A web browser installed on the PC. The minimum browser version requirement is
Internet Explorer v4 or Netscape v4. For the best display quality, use latest version of
Internet Explorer, Netscape or Mozilla Firefox. from any of the LAN computers, launch
your web browser, type the URL, http://192.168.1.1 in the web address (or location)
box, and press [Enter]. The default IP address of the device is 192.168.1.1. Then
enter the default username and password: admin/admin to access the configuration
web page, if you have not changed the username and password. Please be informed
that strings of username and password are case-sentitive.
Figure 5: Login Page
The Menu comprises:
Device Information: provides the basic information of the system. It includes sub
menus, Summary, WAN, Statistics Route, and ARP.
X5671 User’s Guide
Advanced Setup: provides information about the current configuration of various
system features with options to change the configuration. It includes the sub menus
WAN, LAN, Security, Routing, DSL and Port Mapping.
Wireless Setup: provides wireless SSID, security, key and various options to change
the configuration. It includes the sub menu, Basic, Security, MAC Filter, Wireless
Bridge, Advanced, Quality of Service and Station Info.
Diagnostic: provides the diagnostic utility to check the LAN and Wireless physical
connection and ADSL connection as well.
Management: provides the administration utilities. It includes the sub menus, Settings,
System Log, TR-069 Client, Access Control, Update Software, and Save/Reboot.
X5671 User’s Guide
Commonly used buttons
The following buttons are used throughout the web pages:
Button
Function
You could click this button to refresh the information
on this current page again so that you could get the
real time information.
You click this button to create an entry into the list.
You click this button to delete (remove) an entry from
the list.
check button – these appear on many configuration
pages. You will be asked to check if you want this
feature be selected.
This button appears on every configuration page.
Click on this button once you are through with the
changes and decide to save the made changes.
You may need to browse to find a file which needs to
be uploaded for new configuration.
This button allows you to upgrade to the new
configuration file attached using the Browse button.
The following terms are used throughout this guide in association with these buttons:
Click – point the mouse arrow over the button, menu entry or link on the screen and
click the left mouse button. This performs an action, such as displaying a new page or
performing the action specific to the button on which left mouse button is clicked.
Select – usually is used when describing which radio button to select from a list, or
which entry to select from a drop-down list. Point the mouse arrow over the entry and
left-click to select it. This does not perform an action – you will also be required to click
on a button, menu entry or link in order to proceed.
10
X5671 User’s Guide
Testing your Setup
Once you have connected your hardware and configured your PCs, any computer on
your LAN should be able to use the device to access the Internet.
To test the connection, turn on the device, wait seconds till device booting up and then
verify that the LEDs are illuminated as follows:
LED
Behavior
Power
(PWR)
Solid red to indicate that the device is turned on. If
this light is not on, check the power cable
attachment.
Wireless
(WLAN)
Solid green to indicate that the Wireless LAN
function is operational.
Ethernet
Solid green to indicate that the device can
communicate with your LAN.
DSL
Solid green to indicate that the device has
successfully established a connection with your ISP.
Table 1: LED Indicators
If the LEDs illuminate as expected, test your Internet connection from a LAN computer.
To do this, open your web browser, and type the URL of any external website (such
as http://www.yahoo.com).
If the LEDs do not illuminate as expected, you may need to configure your Internet
access settings using the information provided by your ISP. If the LEDs still do not
illuminate as expected or the web page is not displayed, see Troubleshooting section
or contact your ISP for assistance.
Default device settings
The device is preconfigured with default settings for use with a typical home or small
office network.
The table below lists some of the most important default settings; these and other
features are described fully in the subsequent chapters. If you are familiar with
network configuration, review these settings to verify that they meet the needs of your
network. Follow the instructions to change them if necessary. If you are unfamiliar with
these settings, try using the device without modification, or contact your ISP for
assistance.
We strongly recommend that you contact your ISP prior to changing the
default configuration.
WARNING
11
X5671 User’s Guide
Option
Default Setting
Explanation/Instructions
User/Password
admin/admin
User name and password to access
the device
LAN Port
IP Address
Assigned static IP
address:
192.168.1.1
This is the IP address of the LAN port
on the device. The LAN port connects
the device to your Ethernet network.
Typically, you will not need to change
this address. See Local Network
section.
Subnet mask:
255.255.255.0
DHCP
(Dynamic Host
Configuration
Protocol)
DHCP server enabled
with the following pool
of addresses:
192.168.1.2
through
192.168.1.254
(Please be noted that
the default DHCP IP
address pool may be
different in each
firmware version.)
The device maintains a pool of private
IP addresses for dynamic assignment
to your LAN computers. To use this
service, you must have set up your
computers to accept IP information
dynamically, as described in DHCP
Server section.
Table 2: Values of Default Settings (please check default setting.)
12
X5671 User’s Guide
The Device Information web page menu includes the following submenus:
Summary
WAN
Statistics
Route
ARP
Summary
The Summary Page of the device shows the following information, Board ID, Software
version, Bootloader version, VDSL software version, Wireless driver version, and
MAC address. Besides, LAN IP, Default gateway, Primary DNS server and Secondary
DNS server are shown too.
Figure 6: Device Information
WAN
The WAN information of the device shows detailed information about the WAN
connection such as DSL port information (VPI/VCI, UBR/CBR/VBR and so on),
13
X5671 User’s Guide
Protocol, IGMP enabled or disabled, QoS enabled or disabled, IP address of WAN
port and so on.
Figure 7: WAN Port Information
Statistic
The Statistic Page of the device shows the following information, Interfaces, data
transmitting (Received and Transmitted directions) in that interface such as total bytes,
packets, error count and drop count of LAN port, WAN port, ATM, ADSL, and VDSL.
Figure 8: Device WAN Port Statistic Information
Figure 9: Device LAN Port Statistic Information
14
X5671 User’s Guide
Figure 10: Device ATM Statistic Information
Figure 11: Device ADSL Statistic Information
Figure 12: Device VDSL Statistic Information
15
X5671 User’s Guide
Route
The Route Page of the device shows the route table. It contains Destination IP
address, Gateway, Subnet Mask, Flag, Metric, Service and Interface.
Figure 13: Device Route Table Information
ARP
The ARP Page of the device shows the ARP table mapping the IP address and
related MAC address. The ARP table contains IP address, Flag, MAC address,
Device Interface.
Figure 14: Device ARP Table Information
16
X5671 User’s Guide
The Advance Setup menu includes the sub menus WAN, LAN, NAT, Security, Quality
of Service, Routing, DNS, and Port Mapping.
WAN
LAN
Security
Routing
DSL
Port Mapping
WAN
You can configure your internet connection from this page. This page displays the
details of existing internet connection. The device allows 1 bridge connection and 1
route connection existing at that same time without VLAN setting. But if you need
more than 1 bridge connection or 1 route connection, the VLAN tag is required.
Please refer below for more details. There are three connection types can be
configured including PPP over Ethernet (PPPoE), IP over Ethernet, and Bridging.
Figure 15: WAN Setup Page
To configure the WAN port, click Edit or Add to get the configuration pages. If there are
many services (protocols) in the single PVC interface, please enter the unique VLAN
tag number to identify the service (protocol).
Figure 16: WAN Port Configuration
17
X5671 User’s Guide
To configure ATM PVC on the WAN interface:
Enter VPI/VCI values
Check to enable the VLAN Mux that allows multiple protocols in the same PVC
and then enter the 802.11Q VLAN ID valued from 0 to 4095
Select the Service Category from the list (UBR without PCR, UBR with PCR,
CBR, Non Realtime VBR, Realtime VBR). Please leave it as default, UBR with
PCR, if ISP does not give you any information of this setting.
Check to enable the Qualify of Service if Service Category is UBR without PCR,
URB with PCR or Non Realtime VBR and you like this service. Select the
Service Category from the list (UBR without PCR, UBR with PCR, CBR, Non
Realtime VBR, Realtime VBR). Please leave it as default, if ISP does not give
you any information of this setting.
Figure 17: Service Category Configuration
PCR stands for Peak Cell Rate (ATM cells per second). It is the maximum
allowable rate which cells can be transferred in the connection.
SCR stands for Sustainable Cell Rate (ATM cells per second). It is an average
allowable rate which cells can be transferred in the connection.
MRS stands for Maximum Burst Size (ATM cells). It is the maximum allowable
burst size of cells which cells can be transferred in the connection.
Click Next to configure the Connection Type
Figure 18: WAN Connection Type Configuration
Global settings:
Check the WAN protocol from PPP over ATM (PPPoA), PPP over Ethernet
(PPPoE), MAC Encapsulation Routing (MER), IP over ATM (IPoA) and Briding.
18
X5671 User’s Guide
Select the Encapsulation Mode from the list (LLC/SNAP-BRIDGING,
LLC/SNAP-Routing or VC/MUX)
Click Next
PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE)
Figure 19: WAN Connection, PPPoA or PPPoE Configuration
To configure the PPPoA or PPPoE settings:
Enter the User’s PPP Username and Password
Enter the Service Provider Name if any
Select the Authentication Method used during negotiation, default is AUTO.
Check “Dial On Demand” if you do not need PPPoA or PPPoE connection
always ON and enter the timeout value to disconnect the PPPoA or PPPoE
connection when connection is idle and timeout. If you enter “0”, zero for the
timeout value, it means always ON.
Check the “IP extension” if your ISP requests to enable it, otherwise do not
select it. This is a special service to forward IP address assigned by remote to
the local device in the LAN.
Check the “Use Static IP address” and enter the IP address if your ISP assigns
a fixed IP address to you. Otherwise, do not select it.
Check to enable “Retry PPP Password on Authentication Error”.
Check to enable “PPP Debug Mode”
This “Bridge PPP frames between WAN and Local Ports” is checked in default.
Click Next
19
X5671 User’s Guide
Figure 20: WAN Connection, PPPoA or PPPoE Configuration
NAT (Network Address Translation) setting:
Check to enable NAT that allows multiple PCs surfing Internet simultaneously
by using the same WAN IP address.
Check to enable Firewall
Check to enable IGMP Multicast to avoid the multicast packet flooding to other
LAN ports where do not need this IGMP packet to get better efficiency in
Ethernet port.
Check to enable WAN service
Enter the Service Name if you want to change it.
Click Next
The WAN Setup Summary page shows all of parameters.
Figure 21: WAN Connection, PPPoA or PPPoE Configuration
Click Save if correct and click Back to restart the configuration again.
20
X5671 User’s Guide
MAC Encapsulation Routing (MER)
Figure 22: WAN Connection,MER Configuration
To configure the IP over Ethernet settings:
Select “Obtain an IP address automatically” or “Use the following (fixed) IP
address” and then also enter the WAN IP address and WAN Subnet Mask.
Select “Obtain default gateway automatically” or “Use the following default
gateway” and then also enter the gateway IP address and Use WAN Interface
where packets will be sent to.
Select “Obtain DNS server address automatically” or “Use the following DNS
server addresses” and then also enter the IP addresses of Primary DNS server
and Secondary DNS server.
Click Next
The NAT configuration and WAN Setup Summary page will show up. Please refer
related pages above for reference. Click Save if correct and click Back to restart the
configuration again.
21
X5671 User’s Guide
IP over ATM (IPoA)
Figure 23: WAN Connection,MER Configuration
To configure the IP over Ethernet settings:
Enter the WAN IP address and WAN Subnet Mask.
Select “Use the following default gateway” and then also enter the gateway IP
address and Use WAN Interface where packets will be sent to.
Select “Use the following DNS server addresses” and then also enter the IP
addresses of Primary DNS server and Secondary DNS server.
Click Next
The NAT configuration and WAN Setup Summary page will show up. Please refer
related pages above for reference. Click Save if correct and click Back to restart the
configuration again.
22
X5671 User’s Guide
Bridging
Figure 24: WAN Connection, Bridging Configuration
To configure the Bridging settings:
Check “Enable Bridge Service” to enable bridge service
Enter the Service Name for this bridging interface.
Click Next
The WAN Setup Summary page shows all of parameters. Click Save if correct and
click Back to restart the configuration again.
23
X5671 User’s Guide
LAN
Figure 25: LAN Configuration
To configure LAN:
Enter the IP address which the CPE in the LAN will use to connect to the device.
For example, enter 192.168.1.1
Enter the Subnet Mask. For example, enter 255.255.255.0
Check to Enable UPnP feature
Check to Enable IGMP Snooping. This feature will snoop all of IGMP packets and
record related information. Therefore, multicast packets will be generated to the
related LAN ports only to avoid the packet flooding on all of LAN ports. Select
one of two modes, Standard mode or Blocking mode.
Select to Enable or Diable DHCP server. If it is enabled, please enter the DHCP
IP pool of Start IP address and End IP address. Enter the value of leased time of
hour about the valid period of assigned IP address. The DHCP server ON
(enabled) feature will enable this device to assign IP address automatically to PC
in LAN if PC requests an IP address by DHCP client protocol.
Check to enable “Configure the second IP Address and Subnet Mask for LAN
interface” and enter the IP address and Subnet Mask. This is a feature to create
second IP address/subnet in the LAN interface, so that the device can support
two different IP address/subnet networks simultaneously.
Click Save to save the configuration
24
X5671 User’s Guide
NAT (Network Access Translation)
The NAT feature provides the basic firewall feature to avoid hacker attacks from
remote site. There are three more setting pages including virtual server, port trigger,
DMZ and ALG to provide specified service for remote users.
Virtual Server
Virtual Server enables you to run a server on your local network that can be accessed
from the remote parties. You need to set up a rule to tell the device on which computer
the server is held. When port virtual server is enabled, your router (the device) routes
all the inbound traffic on a particular port to the chosen computer on your network.
Figure 26: Virtual Server Setup Configuration
Click Add to add a rule of virtual server.
Figure 27: Add a Rule of Virtual Server
Global Setting
Select a service from the predefined list or enter the name of Custom Server
Enter the Server IP Address located in the LAN to provide the service to remote
party
25
X5671 User’s Guide
Enter the Start External Port # and End External Port # that open to remote to
access the service
Select the Protocol from the list
Enter the Start Internal Port # and End Internal Port # that may use different port
# to secure the service. If you use the same port # as external port #, please
leave Internal Port # as blank.
Click Save/Apply
Port Triggering
The feature is similar to the virtual server, but provides a more secure way to provide
your device. It opens up the port hole temporary and allows CPE in LAN to establish a
connection with remote parties. Those ports are open only if a specified request from
a PC in LAN is received, and then the device allows the remote parties to access to
establish a connection with that PC in LAN.
Figure 28: Port Triggering Setup
Click Add to add a rule of port triggering.
Global Setting
Select a service from the predefined list or enter the name of Custom Server
Enter the Start Trigger Port # and End Trigger Port # that open to remote to
access the service
Select the Trigger Protocol
Enter the Start Open Port # and End Open Port # that may use different port # to
secure the service. If you use the same port # as Trigger port #, please leave
Open Port # as blank.
Select the Open Protocol
Click Save/Apply
26
X5671 User’s Guide
Figure 29: Add a Rule of Port Triggering
DMZ
A DMZ (DeMilitarized Zone) host is a computer on your network that can be accessed
from the Internet. The de-militarised zone (DMZ) is for forwarding IP packets from the
remote parties that are not fixed to any of the applications configured in the virtual
server. These packets are forwarded to a designated DMZ host device. A DMZ is
often used to host Web servers, FTP servers etc that need to be accessible from the
Internet
Figure 30: Add A Rule Of Port Triggering
Global Setting
Enter the DMZ Host IP address
Click Save/Apply
27
X5671 User’s Guide
ALG
A ALG (Application Layer Gateway) is a method to allow specific application to pass
through NAT firewall.
Figure 31: ALG configuration
Global Setting
Check to select SIP ALG enabled
Click Save/Apply
Security
The Security feature provides two more setting pages including IP filtering in Route
mode, MAC filtering and Parental Control.
IP Address Filter
The device can block the packet in outgoing and incoming directions. By default, all
outgoing IP packets from LAN is allowed to surf Internet, but some IP packets can be
blocked by setting up filters.
Figure 32: Outgoing IP Filter Setup
Click Add to add a rule of Outgoing IP Filtering.
Check Remove and click Remove to remove the specified entry.
28
X5671 User’s Guide
Figure 33: Add - Outgoing IP Filter Setup
Global Setting
Enter the Filter Name
Select the Protocol from the selection list.
Enter the Source IP Address and Subnet Mask (range of IP addresses) of packet
Enter the one port or multi ports (port range)
Enter the Destination IP Address and Subnet Mask (range of IP addresses) of
packet
Enter the one port or multi ports (port range)
Click Save/Apply
By default, all incoming IP packets from WAN are blocked to access PCs in LAN, but
some IP packets can be accepted by setting up filters.
Figure 34: Incoming IP Filter Setup
29
X5671 User’s Guide
Click Add to add a rule of Incoming IP Filtering.
Check Remove and click Remove to remove the specified entry.
Figure 35: Add - Incoming IP Filter Setup
Global Setting
Enter the Filter Name
Select the Protocol from the selection list.
Enter the Source IP Address and Subnet Mask (range of IP addresses) of packet
Enter the one port or multi ports (port range)
Enter the Destination IP Address and Subnet Mask (range of IP addresses) of
packet
Enter the one port or multi ports (port range)
Select the WAN interfaces which will be applied with this incoming IP filter rule.
Click Save/Apply
30
X5671 User’s Guide
MAC Filtering
This feature allows you to configure the filter feature based on MAC address. The
default MAC filtering rule is FORWARDED which means that all MAC layer frames will
be forwarded except those matching with any of the specified rules in the MAC
filtering table. The default MAC filtering rule can be changed to BLOCKED. It means
that all MAC layer frames will be blocked except those matching with any of the
specified rule in the MAC filtering table.
Figure 36: MAC Filtering Configuration
Click Change Policy to change the MAC filtering rule between FORWARDED and
BLCOKED.
Figure 37: Change Policy Rule
Click Add to add a rule of MAC filtering.
Check Remove and click Remove to remove the specified entry
Figure 38: Add MAC Filter Rule
31
X5671 User’s Guide
Global Setting
Select the Protocol Type of packet from the list
Enter the Destination MAC Address of packet
Enter the Source MAC Address of packet
Select the Frame Direction, both LAN to WAN and WAN to LAN, LAN to WAN
(outgoing) or WAN to LAN (incoming) from the list
Select the WAN interfaces which will be applied with this MAC filtering rule.
Click Save/Apply to save the configuration
Parental Control
This feature allows you to configure some of PCs in LAN to surf Internet in specific
time period.
Figure 39: Parental Control Configuration
Click Add to add a rule of schedule for parental control.
Check Remove and click Remove to remove the specified entry.
Figure 40: Time of Day Restriction Configuration
32
X5671 User’s Guide
Global Setting
Enter the Username
Select the Browser’s MAC Address or Other MAC Address to enter the specific
PC MAC address.
Check those days you want to block above PC to surf Internet.
Enter the Start Blocking Time and End Blocking Time
Click Save/Apply.
Routing
The section shows the IP addresses or address routes for the computers connected
to the gateway to reach different destinations, such as the local network, the gateway,
or the Internet. The Routing feature provides three more setting pages including
Default Gateway, Static Route and RIP.
Default Gateway
Figure 41: Default Gateway Configuration
Global Setting
Check Enable Automatic Assigned Default Gateway checkbox, this router will
accept the first received default gateway assignment from one of the PPPoA,
PPPoE or Static IP/DHCP interface. If the checkbox is not checked, enter the
static default gateway AND/OR a WAN interface.
Click Save to save the configuration
NOTE: If changing the Automatic Assigned Default Gateway from “unselected” to
“selected”, you must reboot the router to get the automatic assigned default gateway
33
X5671 User’s Guide
Static Route
Figure 42: Static Route Configuration
Click Add to add the static route path.
Figure 43: Add Static Route Configuration
Global Setting
Enter the Destination Network Address and Subnet Mask (range)
Check Use Gateway IP Address and enter the IP address where packet will be
forwarded to.
Check the Use Interface and select it from the list
Click Save to save the configuration
RIP
To activate RIP for the device, select the ‘Enable’ radio button for Global RIP mode. To
configure an individual interface, select the desired RIP version and operation,
followed by placing a check in the ‘Enable’ checkbox for the interface.
Figure 44: Default Gateway Configuration
34
X5671 User’s Guide
Global Setting
Select the Enable to activate this RIP service
Select the desired RIP version and operation, followed by placing a check in the
'Enabled' checkbox for the interface.
Click Save to save the configuration
DNS
The DNS feature provides two more setting pages including DNS server setting and
Dynamic DNS.
DNS Server
Figure 45: DNS Configuration
Global Setting
Check Enable Automatic Assigned DNS checkbox, this router will accept the first
received DNS assignment from one of the PPPoE or Static IP/DHCP interface. If
the checkbox is not checked, enter the IP addresses of the static primary DNS
server and secondary DNS server.
Click Save to save the configuration
Dynamic DNS
The Dynamic DNS feature allows you to bind the dynamic assigned WAN IP address
into a specified domain name. You could pass this domain name to friends to access
your service in your site instead of informing them every times if WAN IP address is
changed.
Figure 46: Dynamic DNS Configuration
35
X5671 User’s Guide
Click Add to add Dynamic DNS setting.
Check Remove and click Remove to remove the specified entry.
Figure 47: Add a Dynamic DNS
Global Setting
Select the Dynamic DNS service provider from the list
Enter the your Hostname
Select the Interface from the list where the device can reach it for registration
Enter the Username and Password for registering IP address of the device to
Dynamic DNS server
Click Save/Apply to save the configuration
DSL
The DSL feature provides basic and advance configuration to set the DSL parameters.
Please contact technician for details before changing any parameters.
Figure 48: DSL Basic Configuration
36
X5671 User’s Guide
Global Setting
Check to select the DSL modulation modes.
Select the DSL phone line pair, inner pair or outer pair. The inner pair is default
setting.
Check to select the Capabilities, Bitswap and SRA (Seamless Rate Adaption).
Click Apply to save the configuration
Click Advanced Settings to get details, please contact technician for support.
Port Mapping
The page provides Port Mapping configuration. In default, the LAN1 to LAN4, wireless,
virtual wireless_guest and Routed PVC are grouped together as a single Ethernet
environment. Port Mapping supports multiple ports to VLAN groups. Each VLAN
group will perform as an independent network. To support this feature, you must
create mapping groups with appropriate LAN and WAN interfaces.
Figure 49: Port Mapping Configuration
Click Add to add VLAN setting.
Check Remove and click Remove to remove the specified entry.
37
X5671 User’s Guide
Figure 50: Add a Port Mapping Configuration
Global Setting
Enter the Group Name
Select the available LAN ports from available LAN interfaces into grouped
interface. The selected LAN interface will be removed from its original group and
joined this new group.
If you like to add LAN clients to a PVC automatically in the new group, add the
DHCP Vendor ID string. By configuring a DHCP vendor ID string, any DHCP
client request with the specified vendor ID (DHCP option 60) will be denied an IP
address from the local DHCP server.
Click Save/Apply to save the configuration.
38
X5671 User’s Guide
The Wireless Setup web page menu comprises:
Basic
Security
MAC Filter
Wireless Bridge
Advanced
Quality of Service
Station Information
Basic
The device provides wireless connection to wireless clients. This page allows you to
enable the wireless service, hide the network from active scan and set the SSID
(Service Set IDentifier). Besides, it allows you to create a virtual wireless AP which
could use different SSID and security key.
Figure 51: Wireless Setting – Basic
Global Setting
Check to enable Wireless feature
Check to enable Hide Access Point to hide from active scan of wireless client
Enter the wireless network name (SSID)
The BSSID is the MAC address of device
Select the Country from the list
Check to enable Wireless Guest Network to create a virtual wireless AP with
different SSID and security key
Enter the Guest SSID
Click Save to save the configuration
39
X5671 User’s Guide
Security
The device provides wireless connection with security including authentication
method and data encryption to protect your data in the air.
Figure 52: Wireless Setting – Security
Global Setting
Select the SSID from the list, then set the related security parameters
Select the method of Network Authentication. It could be OPEN (none), Shared,
802.1X, WPA, WPA-PSK, WPA2, WPA2-PSK, Mixed WPA2/WPA, Mixed
WPA2/WPA-PSK
Select the method of WEP Encryption if Network Authentication is Open. Select
the Encryption Strength with 64bits or 128bits, select the current Key Index and
enter the key and four keys when necessary if WEP Encryption is enabled.
If the Network Authentication is Shared. Select the Encryption Strength with
64bits or 128bits, select the current Key Index and enter the key and four keys
when necessary as the same as Network Authentication is Open and WEP
Encryption is enabled.
If the Network Authentication is 802.1X, enter the IP address and Port number of
Radius server, Radius Key, enable or disable WEP encryption. If WEP
Encryption is enabled, select the Encryption Strength with 64bits or 128bits,
select the current Key Index and enter the key and four keys when necessary.
40
X5671 User’s Guide
If the Network Authentication is WPA, enter WPA Group Rekey Interval, the IP
address and Port number of Radius server, Radius Key, WPA Encryption Method
(TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is
enabled, select the Encryption Strength with 64bits or 128bits, select the current
Key Index and enter the key and four keys when necessary.
If the Network Authentication is WPA-PSK (pre-shared key), enter the WPA
Pre-Shared Key and enter WPA Group Rekey Interval, WPA Encryption Method
(TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is
enabled, select the Encryption Strength with 64bits or 128bits, select the current
Key Index and enter the key and four keys when necessary.
41
X5671 User’s Guide
If the Network Authentication is WPA2, select Enable or Disable for WPA2
Pre-authentication, enter value of Network Re-Auth Interval, enter value of WPA
Group Rekey Interval, the IP address and Port number of Radius server, Radius
Key, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable WEP
encryption. If WEP Encryption is enabled, select the Encryption Strength with
64bits or 128bits, select the current Key Index and enter the key and four keys
when necessary.
If the Network Authentication is WPA2-PSK (pre-shared key), enter the WPA
Pre-Shared Key and enter WPA Group Rekey Interval, WPA Encryption Method
(TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is
enabled, select the Encryption Strength with 64bits or 128bits, select the current
Key Index and enter the key and four keys when necessary.
If the Network Authentication is mixed WPA2/WPA, select Enable or Disable for
WPA2 Pre-authentication, enter value of Network Re-Auth Interval, enter value of
WPA Group Rekey Interval, the IP address and Port number of Radius server,
Radius Key, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable
WEP encryption. If WEP Encryption is enabled, select the Encryption Strength
with 64bits or 128bits, select the current Key Index and enter the key and four
keys when necessary.
42
X5671 User’s Guide
If the Network Authentication is Mixed WPA2/WPA-PSK (pre-shared key), enter
the WPA Pre-Shared Key and enter WPA Group Rekey Interval, WPA Encryption
Method (TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP
Encryption is enabled, select the Encryption Strength with 64bits or 128bits,
select the current Key Index and enter the key and four keys when necessary
Click Save/Apply to save the configuration.
MAC Filter
With this configuration, you could allow or deny wireless to access the device by
wireless MAC address filtering feature. It is disabled as default.
Figure 53: Wireless MAC Filter Configuration
Global Setting
Select the MAC Restrict Mode from one of Disable (no MAC filter), Allow (only
those PCs with MAC addresses in the table can surf Internet) and Deny (only
those PCs with MAC addresses in the table can not surf Internet).
Click Add to add an entry or Remove to remove the specified entry.
Figure 54: Add a Wireless MAC Address
Global Setting
Enter the MAC Address of wireless client
Click Save/Apply to save the configuration.
43
X5671 User’s Guide
Wireless Bridge
The wireless bridge feature is also known as WDS, Wireless Distribution System).
Figure 55: Wireless Bridge Configuration
Global Setting
Set the AP mode as Access Point or Wireless Bridge
When the AP mode is set to Wireless Bridge, the Wireless Restrict determine
where it can communicate with all other wireless bridges and also wireless
clients (set Bridge Restrict is Disabled) or just the specified MAC addresses of
below wireless bridge devices (set Bridge Restrict is Enable).
Click Reflash to get the updated information
Click Save/Apply to save the configuration
Advanced
This page allows you to configure advanced parameters for wireless communication.
Figure 56: Wireless Setting – Advanced
44
X5671 User’s Guide
Global Setting
Enable AP Isolation if you do not want AP to be able to communicate with each
other.
Set the Wireless Communication Band. If you do not know it, please it as default.
Select the channel from the list
Enter the value of Auto Channel Timer
Set the 54g Rate (Wireless Communication Rate), AUTO means to use the
highest rate if possible)
Set the Rate for Multicast Packets, AUTO means to use the highest if possible.
Set the Basic Rate
Set the Fragmentation Threshold values from 256 to 2364 bytes. If the value is
too small, it may cause a result in poor performance.
Set the RTS (Ready to Send) Threshold
Set DTIM Interval. DTIM stands for Delivery Traffic Indication Message. This is a
beacon and is a countdown informing wireless clients of the next window for
listening to broadcast and multicast messages. It is a wake-up interval for clients
in power-saving mode.
Set Beacon Interval. The interval in milliseconds between beacon transmissions.
Set the Maximum Associated Wireless Client
Set XPress Technology enabled or disabled.
Set 54g Mode to 54g Auto, 54g Performance, 802.11b, 54g LRS (limited rate
support).
Set 54g Protection to AUTO if there are 802.11g and 802.11b coexisting in the
wireless network.
Set Afterburner Technology
Set Preamble Type. A preamble is a signal that sync up the timing between
devices.
Set Transmission Power. Larger value means more coverage.
Quality of Service
The device provides wireless quality of service, Wi-Fi Multimedia.
Figure 57: Wireless Setting – Quality of Service
Global Setting
Select to enable or disable WMM (Wi-Fi Multimedia)
Select to enable or disable WMM No Acknowledgement. Enabling
no-acknowledge can result in more efficient throughput but high error rates
45
X5671 User’s Guide
Click Save/Apply to save the configuration
Station Information
The table shows up whole associated wireless clients the device and their status.
Figure 58: Wireless Setting – Station Information
Global Setting
Click Refresh to get the latest updated information
46
X5671 User’s Guide
The Diagnostic web page provides the connection check in physical layer and upper
layer. The result is helpful to figure out the problem if you have problem to surf
Internet.
Diagnostic
This page will show up the result of diagnostic in physical layer like WAN port and also
upper layer of PPP if ISP provides the PPP access protocol.
Figure 59: Diagnostic Result
Global Setting:
Click the Connection to test another connection.
Click the Test to test it again
Click Test with OAM F4 to verify the DSL link.
47
X5671 User’s Guide
The Management web page menu comprises:
Settings
System Log
TR-069 Client
Internet Time
Access Control
Update Software
Save/Reboot
Settings
This page allows you to backup the current configuration of the device, update the
configuration, and restore default configuration (factory setting).
Backup
Figure 60: Backup Settings
Click Backup Settings to backup the current settings of the device into file in PC.
Update
Figure 61: Restore Default Settings
Click Browser to specify the configuration file (settings) in PC and click Update
Settings to upload the settings to the device.
48
X5671 User’s Guide
Restore Default
Figure 62: Restore Default Settings
Click Restore Default Settings to restore the factory default settings.
System Log
This page allows you to view system log and also configure system log that way you
want to see.
Figure 63: Management Configuration – System Log
Global Setting
Click View System Log to view system log
Click Configure System Log to configure the way you want to see
Figure 64: Management Configuration – Configure System Log
49
X5671 User’s Guide
Global Setting
Select to Enable Log function or not
Select Log Level from the list
Select Display Level from the list
Select Mode from the list
Click Save/Apply to save the configuration.
TR-069 Client
This page allows you to access TR-069 ACS (Auto-Configuration Server). The ACS
can provision, configure, and diagnostic the device from remote site.
Figure 65: Management Configuration – Firmware Upgrade
Global Setting
Select to Enable or Disable to send Inform packet to ACS.
Enter the Inform Interval number of seconds. The Inform packet will be sent to
ACS periodically.
Enter the ACS URL to reach ACS
Enter the ACS User Name and Password
Enter the Connection Request User Name and Password
Click Save/Apply to save the configuration
50
X5671 User’s Guide
Internet Time
This page allows you to sync up the real time clock from Internet. .
Figure 66: Internet Time Configuration
Global Setting
Check to Automatically synchronize with Internet time servers
Click Save to save your settings
Access Control
This submenu provides you local (LAN) or remote (WAN) access to the device. This
may help the IT support staff to configure the router locally or remotely.
Service
Figure 67: Management Configuration – Access Control: Service
51
X5671 User’s Guide
Global Setting:
4 Specify the method by which you wish to access the router locally or remotely by
selecting it. The following are the methods available for local and remote access:
FTP
HTTP
ICMP (Ping)
SSH
TELNET
TFTP
4 Click Save/Apply to save the configuration.
IP Address
Figure 68: Management Configuration – Access Control: IP Address
Click to enable or disable Access Control by IP address.
Click Add to add IP address.
Check Remove and click Remove to remove the specified entry.
Figure 69: Management Configuration – Access Control: Add IP Address
Global Setting:
4 Add the IP Address which is permitted to access the device and execute the
management service.
Click Save/Apply to save the settings.
Password
There are three levels of access accounts: admin, support, and user. The user name
“admin” has unrestricted access to change and view configuration of the device. The
user name “support” is used to allow an ISP technician to access the device for
maintenance and to run diagnostics. The user name “user” can access the device,
52
X5671 User’s Guide
view configuration settigns and statistics, as well as updaet the device software.
Figure 70: Management Configuration – Access Control: Password
Global Setting:
4 Select the level of Username
4 Enter the Old Password
4 Enter the New Password and Confirm Password
4 Click Save/Apply to save the configuration.
53
X5671 User’s Guide
Update Software
This page allows you to upgrade the software (firmware).
Figure 71: Management Configuration – Update Software
Global Setting:
4 First of all, you have to get the updated software (firmware) from ISP or
manufacture.
4 Click Browser to specify the location and filename
4 Click Update Software to start the process. It could take minutes to complete it.
Save / Reboot
This page allows you to save current configuration and reboot to use the settings.
Figure 72: Management Configuration – Save/Reboot (no picture)
Global Setting
Click Save/Reboot to save the changes and reboot the device.
Click Reboot to discard changes and reboot the device only
54
X5671 User’s Guide
This appendix provides instructions for configuring the Internet settings on your
computers to work with the device.
Configuring Ethernet PCs
Before you begin
By default, the device automatically assigns the required Internet settings to your PCs.
You need to configure the PCs to accept this information when it is assigned.
Note
In some cases, you may want to assign Internet information
manually to some or all of your computers rather than allow the
device to do so. See
Assigning static Internet information to your PCs section.
If you have connected your LAN PCs via Ethernet to the device, follow the
instructions that correspond to the operating system installed on your PC:
Windows® XP PCs
Windows 2000 PCs
Windows Me PCs
Windows\ 95, 98 PCs
Windows NT 4.0 workstations
If you want to allow Wireless PCs to access your device, follow the instructions in
Configuring Wireless PCs below..
Windows® XP PCs
In the Windows task bar, click the Start button, and then click Control Panel.
Double-click the Network Connections icon.
In the LAN or High-Speed Internet window, right-click on the icon corresponding to
your network interface card (NIC) and select Properties. (Often, this icon is labelled
Local Area Connection).The Local Area Connection dialog box is displayed with a list
of currently installed network items.
Ensure that the check box to the left of the item labelled Internet Protocol TCP/IP is
checked and click Properties.
In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labelled
Obtain an IP address automatically. Also click the radio button labelled Obtain DNS
server address automatically.
Click OK twice to confirm your changes, and then close the Control Panel.
Windows 2000 PCs
First, check for the IP protocol and, if necessary, install it:
In the Windows task bar, click the Start button, point to Settings, and then click Control
Panel.
Double-click the Network and Dial-up Connections icon.
In the Network and Dial-up Connections window, right-click the Local Area Connection
icon, and then select Properties. The Local Area Connection Properties dialog box is
55
X5671 User’s Guide
displayed with a list of currently installed network components. If the list includes
Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step
10.
If Internet Protocol (TCP/IP) does not display as an installed component, click Install.
In the Select Network Component Type dialog box, select Protocol, and then click
Add.
Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click OK. You
may be prompted to install files from your Windows 2000 installation CD or other
media. Follow the instructions to install the files.
If prompted, click OK to restart your computer with the new settings. Next, configure
the PCs to accept IP information assigned by the device.
In the Control Panel, double-click the Network and Dial-up Connections icon.
In the Network and Dial-up Connections window, right-click the Local Area Connection
icon, and then select Properties.
In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP),
and then click Properties.
In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labelled
Obtain an IP address automatically. Also click the radio button labelled Obtain DNS
server address automatically.
Click OK twice to confirm and save your changes, and then close the Control Panel.
Windows Me PCs
In the Windows task bar, click the Start button, point to Settings, and then click Control
Panel.
Double-click the Network and Dial-up Connections icon.
In the Network and Dial-up Connections window, right-click the Network icon, and
then select Properties. The Network Properties dialog box displays with a list of
currently installed network components. If the list includes Internet Protocol (TCP/IP),
then the protocol has already been enabled. Skip to step 11.
If Internet Protocol (TCP/IP) does not display as an installed component, click Add.
In the Select Network Component Type dialog box, select Protocol, and then click
Add.
Select Microsoft in the Manufacturers box.
Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click OK. You
may be prompted to install files from your Windows Me installation CD or other media.
Follow the instructions to install the files.
If prompted, click OK to restart your computer with the new settings. Next, configure
the PCs to accept IP information assigned by the device.
In the Control Panel, double-click the Network and Dial-up Connections icon.
In Network and Dial-up Connections window, right-click the Network icon, and then
select Properties.
In the Network Properties dialog box, select TCP/IP, and then click Properties.
In the TCP/IP Settings dialog box, click the radio button labelled Server assigned IP
address. Also click the radio button labelled Server assigned name server address.
Click OK twice to confirm and save your changes, and then close the Control Panel.
Windows 95, 98 PCs
First, check for the IP protocol and, if necessary, install it:
56
X5671 User’s Guide
In the Windows task bar, click the Start button, point to Settings, and then click Control
Panel.
Double-click the Network icon. The Network dialog box displays with a list of currently
installed network components. If the list includes TCP/IP, and then the protocol has
already been enabled. Skip to step 9.
If TCP/IP does not display as an installed component, click Add. The Select Network
Component Type dialog box displays.
Select Protocol, and then click Add…The Select Network Protocol dialog box
displays.
Click on Microsoft in the Manufacturers list box, and then click TCP/IP in the Network
Protocols list box.
Click OK to return to the Network dialog box, and then click OK again. You may be
prompted to install files from your Windows 95/98 installation CD. Follow the
instructions to install the files.
Click OK to restart the PC and complete the TCP/IP installation. Next, configure the
PCs to accept IP information assigned by the device.
Open the Control Panel window, and then click the Network icon.
Select the network component labelled TCP/IP, and then click Properties. If you have
multiple TCP/IP listings, select the listing associated with your network card or
adapter.
In the TCP/IP Properties dialog box, click the IP Address tab.
Click the radio button labelled Obtain an IP address automatically.
Click the DNS Configuration tab, and then click the radio button labelled Obtain an IP
address automatically.
Click OK twice to confirm and save your changes. You will be prompted to restart
Windows.
Click Yes.
Windows NT 4.0 workstations
First, check for the IP protocol and, if necessary, install it:
In the Windows NT task bar, click the Start button, point to Settings, and then click
Control Panel.
In the Control Panel window, double click the Network icon.
In the Network dialog box, click the Protocols tab. The Protocols tab displays a list of
currently installed network protocols. If the list includes TCP/IP, then the protocol has
already been enabled. Skip to step 9.
If TCP/IP does not display as an installed component, click Add.
In the Select Network Protocol dialog box, select TCP/IP, and then click OK. You may
be prompted to install files from your Windows NT installation CD or other media.
Follow the instructions to install the files. After all files are installed, a window displays
to inform you that a TCP/IP service called DHCP can be set up to dynamically assign
IP information.
Click Yes to continue, and then click OK if prompted to restart your computer. Next,
configure the PCs to accept IP information assigned by the device.
Open the Control Panel window, and then double-click the Network icon.
In the Network dialog box, click the Protocols tab.
In the Protocols tab, select TCP/IP, and then click Properties.
In the Microsoft TCP/IP Properties dialog box, click the radio button labelled Obtain an
IP address from a DHCP server.
57
X5671 User’s Guide
Click OK twice to confirm and save your changes, and then close the Control Panel.
Assigning static Internet information to your PCs
If you are a typical user, you will not need to assign static Internet information to your
LAN PCs because your ISP automatically assigns this information for you.
In some cases however, you may want to assign Internet information to some or all of
your PCs directly (often called “statically”), rather than allowing the device to assign it.
This option may be desirable (but not required) if:
You have obtained one or more public IP addresses that you want to always
associate with specific computers (for example, if you are using a computer as
a public web server).
You maintain different subnets on your LAN (subnets are described in
Appendix B).
Before you begin, you must have the following information available:
The IP address and subnet mask of each PC
The IP address of the default gateway for your LAN. In most cases, this is the
address assigned to the LAN port on the device. By default, the LAN port is
assigned the IP address 192.168.1.1. (You can change this number or another
number can be assigned by your ISP.)
The IP address of your ISP’s Domain Name System (DNS) server.
On each PC to which you want to assign static information, follow the instructions
relating only to checking for and/or installing the IP protocol. Once it is installed,
continue to follow the instructions for displaying each of the Internet Protocol (TCP/IP)
properties. Instead of enabling dynamic assignment of the IP addresses for the
computer, DNS server and default gateway, click the radio buttons that enable you to
enter the information manually.
Note
Your PCs must have IP addresses that place them in the same
subnet as the device’s LAN port.
58
X5671 User’s Guide
Configuring Wireless PCs
You need to configure the operating system installed on your Wireless PCs using the
same procedure described for Configuring Ethernet PCs section.
Positioning the wireless PCs
The wireless network cards used determine the maximum distance between your
wireless PCs and your device. Guidelines on positioning the hardware components of
your wireless network should be provided by your network card provider.
Wireless PC cards and drivers
Each PC on your wireless LAN must be fitted with a wireless access card. You must
also install the corresponding driver files for your particular wireless card on your PC.
You should receive driver files and instructions on how to install them together with
your wireless card.
Configuring PC access to your Wireless device
Before you start configuring your Wireless PC, you must ensure that you have:
A Wireless access card for each of the PCs
Corresponding wireless access card driver software files
The configuration steps below will vary depending on both the operating system and
wireless card installed on the PC. These steps provide a basic outline, however you
should refer to the documentation provided with your wireless access card for specific
instructions.
To configure Wireless PCs:
Install the wireless access card.
Install the wireless driver software files.
Configure the following wireless parameters on each of the wireless PCs:
• Set the adapter to use infrastructure mode. This configures the PCs to access each
other and the Internet via the device.
Configure the SSID and channel to match the SSID and channel previously
configured on the device.
Your wireless network can now communicate with the Internet via the device.
59
X5671 User’s Guide
This appendix suggests solutions for problems you may encounter in installing or
using the device, and provides instructions for using several IP utilities to diagnose
problems.
Contact Customer Support if these suggestions do not resolve the problem.
Troubleshooting Suggestions
Problem
Troubleshooting Suggestion
LEDs
Power LED does not illuminate
after product is turned on.
LINK LAN LED does not
illuminate after Ethernet cable is
attached.
Verify that you are using the power cable
provided with the device and that it is securely
connected to the device and a wall
socket/power strip.
Verify that the Ethernet cable is securely
connected to your LAN hub or PC and to the
device. Make sure the PC and/or hub is turned
on.
Verify that your cable is sufficient for your
network requirements. A 100 Mbit/sec network
(10BaseTx) should use cables labeled CAT 5.
A 10Mbit/sec network may tolerate lower
quality cables.
Internet Access
My PC cannot access the Internet
Run a health check on your device. Use the
ping utility (discussed in the following section)
to check whether your PC can communicate
with the device’s LAN IP address (by default
192.168.1.1). If it cannot, check the Ethernet
cabling.
If you statically assigned a private IP address to
the computer, (not a registered public address),
verify the following:
My LAN PCs cannot display
web pages on the Internet.
Check that the gateway IP address on the
computer is your public IP address (see
Current Status on page 1 for instructions
on viewing the IP information.) If it is not,
correct the address or configure the PC to
receive IP information automatically.
Verify with your ISP that the DNS server
specified for the PC is valid. Correct the
address or configure the PC to receive
this information automatically.
Verify that the DNS server IP address specified
on the PCs is correct for your ISP, as
discussed in the item above. If you specified
that the DNS server be assigned dynamically
from a server, then verify with your ISP that the
address configured on the device is correct,
and then you can use the ping utility, discussed
on page 61, to test connectivity with your ISP’s
DNS server.
Web pages
60
X5671 User’s Guide
Problem
Troubleshooting Suggestion
I forgot/lost my user ID or
password.
If you have not changed the password from the
default, try using “admin” as both the user ID
and password. Otherwise, you can reset the
device to the default configuration by pressing
three times the Reset Default button on the
front panel of the device. Then, type the default
User ID and password shown above.
WARNING: Resetting the device removes any
custom settings and returns all settings to their
default values.
Use the ping utility, discussed in the following
section, to check whether the PC can
communicate with the device’s LAN IP address
(by default 192.168.1.1). If it cannot, check the
Ethernet cabling.
Verify that you are using Internet Explorer or
Netscape Navigator v4.0 or later.
Verify that the PC’s IP address is defined as
being on the same subnet as the IP address
assigned to the LAN port on the device.
I cannot access the web pages
from my browser.
My changes to the web pages
are not being retained.
Be sure to use the Confirm Changes function
after any changes.
Diagnosing Problem using IP Utilities
Ping
Ping is a command you can use to check whether your PC can recognize other
computers on your network and the Internet. A ping command sends a message to
the computer you specify. If the computer receives the message, it sends messages
in reply. To use it, you must know the IP address of the computer with which you are
trying to communicate.
On Windows-based computers, you can execute a ping command from the Start
menu. Click the Start button, and then click Run. In the Open text box, type a
statement such as the following:
ping 192.168.1.1
Click OK. You can substitute any private IP address on your LAN or a public IP
address for an Internet site, if known.
If the target computer receives the message, a Command Prompt window is
displayed:
If the target computer cannot be located, you will receive the message Request timed
out.
Using the ping command, you can test whether the path to the device is working
(using the preconfigured default LAN IP address 192.168.1.1) or another address you
assigned.
61
X5671 User’s Guide
You can also test whether access to the Internet is working by typing an external
address, such as that for www.yahoo.com (216.115.108.243). If you do not know the
IP address of a particular Internet location, you can use the nslookup command, as
explained in the following section.
From most other IP-enabled operating systems, you can execute the same command
at a command prompt or through a system administration utility.
Nslookup
You can use the nslookup command to determine the IP address associated with an
Internet site name. You specify the common name, and the nslookup command looks
up the name in on your DNS server (usually located with your ISP). If that name is not
an entry in your ISP’s DNS table, the request is then referred to another higher-level
server, and so on, until the entry is found. The server then returns the associated IP
address.
On Windows-based computers, you can execute the nslookup command from the
Start menu. Click the Start button, and then click Run. In the Open text box, type the
following:
Nslookup
Click OK. A Command Prompt window displays with a bracket prompt (>). At the
prompt, type the name of the Internet address that you are interested in, such as
www.microsoft.com.
The window will display the associate IP address, if known, as shown below:
There may be several addresses associated with an Internet name. This is common
for web sites that receive heavy traffic; they use multiple, redundant servers to carry
the same information.
To exit from the nslookup utility, type exit and press [Enter] at the command prompt.
62
X5671 User’s Guide
Term
Description
802.11
A family of specifications for wireless
LANs developed by a working group of the IEEE. This
wireless Ethernet protocol, often called Wi-Fi.
10BASE-T
A designation for the type of wiring used by Ethernet
networks with a data rate of 10 Mbps. Also known as
Category 3 (CAT 3) wiring. See data rate, Ethernet.
100BASE-T
A designation for the type of wiring used by Ethernet
networks with a data rate of 100 Mbps. Also known as
Category 5 (CAT 5) wiring. See data rate, Ethernet.
ADSL
Asymmetric Digital Subscriber Line
The most commonly deployed “flavor” of DSL for home
users is asymmetrical DSL. The term asymmetrical
refers to its unequal data rates for downloading and
uploading (the download rate is higher than the upload
rate). The asymmetrical rates benefit home users
because they typically download much more data from
the Internet than they upload.
An analog signal is a signal that has had its frequency
modified in some way, such as by amplifying its strength
or varying its frequency, in order to add information to
the signal. The voice component in DSL is an analog
signal. See digital.
Asynchronous Transfer Mode
A standard for high-speed transmission of data, text,
voice, and video, widely used within the Internet. ATM
data rates range from 45 Mbps to 2.5 Gbps. See data
rate.
To verify a user’s identity, such as by prompting for a
password.
Analog
ATM
Authenticate
Binary
Bit
The “base two” system of numbers that uses only two
digits, 0 and 1, to represent all numbers. In binary, the
number 1 is written as 1, 2 as 10, 3 as 11, 4 as 100, etc.
Although expressed as decimal numbers for
convenience, IP addresses in actual use are binary
numbers; e.g., the IP address 209.191.4.240 is
11010001.10111111.00000100.11110000 in binary.
See bit, IP address, network mask.
Short for “binary digit,” a bit is a number that can have
two values, 0 or 1. See binary.
Bps
bits per second
Bridging
Passing data from your network to your ISP and vice
versa using the hardware addresses of the devices at
each location. Bridging contrasts with routing which can
add more intelligence to data transfers by using network
addresses instead. The device can perform both routing
and bridging. Typically, when both functions are
enabled, the device routes IP data and bridges all other
63
X5671 User’s Guide
types of data. See routing.
Broadband
A telecommunications technology that can send
different types of data over the same medium. DSL is a
broadband technology.
Broadcast
To send data to all computers on a network.
DHCP
Dynamic Host Configuration Protocol
DHCP automates address assignment and
management. When a computer connects to the LAN,
DHCP assigns it an IP address from a shared pool of IP
addresses; after a specified time limit, DHCP returns the
address to the pool.
Dynamic Host Configuration Protocol relay
A DHCP relay is a computer that forwards DHCP data
between computers that request IP addresses and the
DHCP server that assigns the addresses. Each of the
device’s interfaces can be configured as a DHCP relay.
See DHCP.
Dynamic Host Configuration Protocol server
A DHCP server is a computer that is responsible for
assigning IP addresses to the computers on a LAN. See
DHCP.
DHCP relay
DHCP server
Digital
Of data, having a form based on discrete values
expressed as binary numbers (0’s and 1’s). The data
component in DSL is a digital signal. See analog.
DNS
Domain Name System
The DNS maps domain names into IP addresses. DNS
information is distributed hierarchically throughout the
Internet among computers called DNS servers. For
example, www.yahoo.com is the domain name
associated with IP address 216.115.108.243. When you
start to access a web site, a DNS server looks up the
requested domain name to find its corresponding IP
address. If the DNS server cannot find the IP address, it
communicates with higher-level DNS servers to
determine the IP address. See domain name.
A domain name is a user-friendly name used in place of
its associated IP address. Domain names must be
unique; their assignment is controlled by the Internet
Corporation for Assigned Names and Numbers
(ICANN). Domain names are a key element of URLs,
which identify a specific file at a web site. See DNS.
To transfer data in the downstream direction, i.e., from
the Internet to the user.
Domain name
Download
DSL
Digital Subscriber Line
A technology that allows both digital data and analog
voice signals to travel over existing copper telephone
lines.
Encryption keys
See network keys
Ethernet
The most commonly installed computer network
technology, usually using twisted pair wiring. Ethernet
data rates are 10 Mbps and 100 Mbps. See also
10BASE-T, 100BASE-T, twisted pair.
64
X5671 User’s Guide
FTP
Gbps
File Transfer Protocol
A program used to transfer files between computers
connected to the Internet. Common uses include
uploading new or updated files to a web server, and
downloading files from a web server.
Abbreviation of Gigabits per second, or one billion bits
per second. Internet data rates are often expressed in
Gbps.
Host
A device (usually a computer) connected to a network.
HTTP
Hyper-Text Transfer Protocol
HTTP is the main protocol used to transfer data from
web sites so that it can be displayed by web browsers.
See web browser, web site.
Hub
A hub is a place of convergence where data arrives from
one or more directions and is forwarded out in one or
more directions. It connects an Ethernet bridge/router to
a group of PCs on a LAN and allows communication to
pass between the networked devices.
Internet Control Message Protocol
An Internet protocol used to report errors and other
network-related information. The ping command makes
use of ICMP.
ICMP
IEEE
The Institute of Electrical and Electronics Engineers is a
technical professional society that fosters the
development of standards that often become national
and international standards.
Internet
The global collection of interconnected networks used
for both private and business communications.
Intranet
A private, company-internal network that looks like part
of the Internet (users access information using web
browsers), but is accessible only by employees.
IP
See TCP/IP.
IP address
Internet Protocol address
The address of a host (computer) on the Internet,
consisting of four numbers, each from 0 to 255,
separated by periods, e.g., 209.191.4.240. An IP
address consists of a network ID that identifies the
particular network the host belongs to, and a host ID
uniquely identifying the host itself on that network. A
network mask is used to define the network ID and the
host ID. Because IP addresses are difficult to
remember, they usually have an associated domain
name that can be specified instead. See domain name,
network mask.
Internet Service Provider
A company that provides Internet access to its
customers, usually for a fee.
ISP
LAN
Local Area Network.
A network limited to a small geographic area, such as a
home or small office.
65
X5671 User’s Guide
LED
Light Emitting Diode
An electronic light-emitting device. The indicator lights
on the front of the device are LEDs.
MAC address
Media Access Control address
The permanent hardware address of a device, assigned
by its manufacturer. MAC addresses are expressed as
six pairs of hex characters, with each pair separated by
colons. For example; NN:NN:NN:NN:NN:NN.
See network mask.
Mask
Mbps
Abbreviation for Megabits per second, or one million bits
per second. Network data rates are often expressed in
Mbps.
NAT
Network Address Translation
A service performed by many routers that translates
your network’s publicly known IP address into a private
IP address for each computer on your LAN. Only your
router and your LAN know these addresses; the outside
world sees only the public IP address when talking to a
computer on your LAN.
A group of computers that are connected together,
allowing them to communicate with each other and
share resources, such as software, files, etc. A network
can be small, such as a LAN, or very large, such as the
Internet.
(Also known as encryption keys.) 64-bit and 128-bit
encryption keys used in WEP wireless security
schemes. The keys encrypt data over the WLAN, and
only wireless PCs configured with WEP keys that
correspond to the keys configured on the device can
send/receive encrypted data.
A network mask is a sequence of bits applied to an IP
address to select the network ID while ignoring the host
ID. Bits set to 1 mean “select this bit” while bits set to 0
mean “ignore this bit.” For example, if the network mask
255.255.255.0 is applied to the IP address 100.10.50.1,
the network ID is 100.10.50, and the host ID is 1. See
binary, IP address, subnet.
Network Interface Card
An adapter card that plugs into your computer and
provides the physical interface to your network cabling.
For Ethernet NICs this is typically an RJ-45 connector.
See Ethernet, RJ-45.
Data transmitted on a network consists of units called
packets. Each packet contains a payload (the data),
plus overhead information such as where it came from
(source address) and where it should go (destination
address).
Packet Internet (or Inter-Network) Groper
A program used to verify whether the host associated
with an IP address is online. It can also be used to
reveal the IP address for a given domain name.
Network
Network keys
Network mask
NIC
Packet
Ping
Port
A physical access point to a device such as a computer
or router, through which data flows into and out of the
device.
PPP
Point-to-Point Protocol
A protocol for serial data transmission that is used to
carry IP (and other protocol) data between your ISP and
your computer. The WAN interface on the device uses
two forms of PPP called PPPoA and PPPoE. See
PPPoA, PPPoE.
66
X5671 User’s Guide
PPPoA
Point-to-Point Protocol over ATM
One of the two types of PPP interfaces you can define
for a Virtual Circuit (VC), the other type being PPPoE.
You can define only one PPPoA interface per VC.
PPPoE
Point-to-Point Protocol over Ethernet
One of the two types of PPP interfaces you can define
for a Virtual Circuit (VC), the other type being PPPoA.
You can define one or more PPPoE interfaces per VC.
Protocol
A set of rules governing the transmission of data. In
order for a data transmission to work, both ends of the
connection have to follow the rules of the protocol.
Remote
In a physically separate location. For example, an
employee away on travel who logs in to the company’s
intranet is a remote user.
RIP
Routing Information Protocol
The original TCP/IP routing protocol. There are two
versions of RIP: version I and version II.
RJ-11
Registered Jack Standard-11
The standard plug used to connect telephones, fax
machines, modems, etc. to a telephone port. It is a 6-pin
connector usually containing four wires.
RJ-45
Registered Jack Standard-45
The 8-pin plug used in transmitting data over phone
lines. Ethernet cabling usually uses this type of
connector.
Routing
Forwarding data between your network and the Internet
on the most efficient route, based on the data’s
destination IP address and current network conditions.
A device that performs routing is called a router.
SDNS
Secondary Domain Name System (server)
A DNS server that can be used if the primary DSN
server is not available. See DNS.
Subnet
Subnet mask
A subnet is a portion of a network. The subnet is
distinguished from the larger network by a subnet mask
that selects some of the computers of the network and
excludes all others. The subnet’s computers remain
physically connected to the rest of the parent network,
but they are treated as though they were on a separate
network. See network mask.
A mask that defines a subnet. See network mask.
TCP
See TCP/IP.
TCP/IP
Transmission Control Protocol/Internet Protocol
The basic protocols used on the Internet. TCP is
responsible for dividing data up into packets for delivery
and reassembling them at the destination, while IP is
responsible for delivering the packets from source to
destination. When TCP and IP are bundled with
higher-level applications such as HTTP, FTP, Telnet,
etc., TCP/IP refers to this whole suite of protocols.
An interactive, character-based program used to access
a remote computer. While HTTP (the web protocol) and
FTP only allow you to download files from a remote
computer, Telnet allows you to log into and use a
computer from a remote location.
Telnet
67
X5671 User’s Guide
TFTP
Trivial File Transfer Protocol
A protocol for file transfers, TFTP is easier to use than
File Transfer Protocol (FTP) but not as capable or
secure.
TKIP
Temporal Key Integrity Protocol (TKIP) provides WPA
with a data encryption function. It ensures that a unique
master key is generated for each packet, supports
message integrity and sequencing rules and supports
re-keying mechanisms.
Triggers are used to deal with application protocols that
create separate sessions. Some applications, such as
NetMeeting, open secondary connections during normal
operations, for example, a connection to a server is
established using one port, but data transfers are
performed on a separate connection. A trigger tells the
device to expect these secondary sessions and how to
handle them.
Once you set a trigger, the embedded IP address of
each incoming packet is replaced by the correct host
address so that NAT can translate packets to the correct
destination. You can specify whether you want to carry
out address replacement, and if so, whether to replace
addresses on TCP packets only, UDP packets only, or
both.
The ordinary copper telephone wiring used by telephone
companies. It contains one or more wire pairs twisted
together to reduce inductance and noise. Each
telephone line uses one pair. In homes, it is most often
installed with two pairs. For Ethernet LANs, a higher
grade called Category 3 (CAT 3) is used for 10BASE-T
networks, and an even higher grade called Category 5
(CAT 5) is used for 100BASE-T networks. See
10BASE-T, 100BASE-T, Ethernet.
An unnumbered interface is an IP interface that does not
have a local subnet associated with it. Instead, it uses a
router-id that serves as the source and destination
address of packets sent to and from the router. Unlike
the IP address of a normal interface, the router-id of an
unnumbered interface is allowed to be the same as the
IP address of another interface. For example, the WAN
unnumbered interface of your device uses the same IP
address of the LAN interface (192.168.1.1).
The unnumbered interface is temporary – PPP or DHCP
will assign a ‘real’ IP address automatically.
The direction of data transmission from the user to the
Internet.
Triggers
Twisted pair
Unnumbered interfaces
Upstream
VC
Virtual Circuit
A connection from your DSL router to your ISP.
VCI
Virtual Circuit Identifier
Together with the Virtual Path Identifier (VPI), the VCI
uniquely identifies a VC. Your ISP will tell you the VCI
for each VC they provide. See VC.
VDSL
Very High Speed Digital Subscriber Line
It provides faster transmission rate and is capable of
supporting high bandwidth applications like IPTV and
bandwidth consumed applications.
VPI
Virtual Path Identifier
Together with the Virtual Circuit Identifier (VCI), the VPI
uniquely identifies a VC. Your ISP will tell you the VPI
for each VC they provide. See VC.
68
X5671 User’s Guide
WAN
Wide Area Network
Any network spread over a large geographical area,
such as a country or continent. With respect to the
device, WAN refers to the Internet.
Web browser
A software program that uses Hyper-Text Transfer
Protocol (HTTP) to download information from (and
upload to) web sites, and displays the information, which
may consist of text, graphic images, audio, or video, to
the user. Web browsers use Hyper-Text Transfer
Protocol (HTTP). Popular web browsers include
Netscape Navigator and Microsoft Internet Explorer.
See HTTP, web site, WWW.
A web site file typically containing text, graphics and
hyperlinks (cross-references) to the other pages on that
web site, as well as to pages on other web sites. When a
user accesses a web site, the first page that is displayed
is called the home page. See hyperlink, web site.
A computer on the Internet that distributes information to
(and gets information from) remote users through web
browsers. A web site typically consists of web pages
that contain text, graphics, and hyperlinks. See
hyperlink, web page.
Wired Equivalent Privacy (WEP) encrypts data over
WLANs. Data is encrypted into blocks of either 64 bits
length or 128 bits length. The encrypted data can only
be sent and received by users with access to a private
network key. Each PC on your wireless network must be
manually configured with the same key as your device in
order to allow wireless encrypted data transmissions.
Eavesdroppers cannot access your network if they do
not know your private key. WEP is considered to be a
low security option.
Wireless is a term used to describe telecommunications
in which electromagnetic waves (rather than some form
of wire) carry the signal over part or the entire
communication path. See wireless LAN.
Web page
Web site
WEP
Wireless
Wireless LAN
A wireless LAN (WLAN) is one in which a mobile user
can connect to a local area network (LAN) through a
wireless (radio) connection. A standard, IEEE 802.11,
specifies the technologies for wireless LANs.
WPA
Wi-Fi Protected Access
WPA is an initiative by the IEEE and Wi-Fi Alliance to
address the security limitations of WEP. WPA provides
a stronger data encryption method (called Temporal Key
Integrity Protocol (TKIP)). It runs in a special,
easy-to-set-up home mode called Pre-Shared Key
(PSK) that allows you to manually enter a pass phrase
on all the devices in your wireless network. WPA data
encryption is based on a WPA master key. The master
key is derived from the pass phrase and the network
name (SSID) of the device.
It provides improved data encryption and stronger user
authentication. The mode of WPA supported on your
device is called Pre-Shared Key (PSK), which allows
you to manually enter a type of key called a pass
phrase.
World Wide Web
Also called (the) Web. Collective term for all web sites
anywhere in the world that can be accessed via the
Internet.
WWW
69
X5671 User’s Guide
A1.
Hardware Specifications
•
LAN Interface
Four port 10/100BaseT Ethernet Switch (4 * RJ-45 connectors), IEEE 802.3u
with MDI/MDIX auto-detection
•
Integrated 802.11b/g WLAN Access Point
•
•
•
WAN VDSL2 Line Interface
Compliant with VDSL2 and support 8a/8b/8c/8d, 17a and 30a
Connection Loops: One (pair wire)
Connector: RJ-11
•
•
•
Indicators
PWR – Green LED indicates power and operation. Red LED indicates failure.
DSL – Green LED indicates broadband connection
Internet – Green LED indicates PPP connection and RED indicates PPP failure
or device in BRIDGE mode.
•
Ethernet – Green LED indicates LAN connection
•
WLAN – Green LED indicates wireless AP enabled
•
•
•
•
Environment
Operation Temperature: 0°C ~ 45°C
Operation Humidity: 5% ~ 95%
Storage Temperature: -20 ~ +85°C
Storage Humidity: 5%~95%
•
Power
AC Adapter: Input 110/220VAC, 50/60Hz; Output 12VDC 1.50A
•
Certificates
CE, CB (TBD)
70
X5671 User’s Guide
A2.
Software Specifications
Bridging
Transparent Bridging and spanning(IEEE 802.1D) with at least 32 MAC
addresses
RFC2684 (RFC 1483) Bridged
Bridge filtering with per-port extensions
Routing
IP routing and PPP supported
PAP and CHAP for user authentication in PPP connection
RFC2684 (RFC1483) Routed
MAC Encapsulated Routing (MER)
DHCP client, server and relay agent
DNS relay
Wireless LAN
Supports 802.1x; WEP; WEP2; WPA; WPA2; TKIP; AES;
Hidden SSID
WMM for advanced Quality of Service
Supports TKIP and AES
Firewall
Support NAT and DMZ
Protection against IP and MAC address spoofing
UPnP NAT traversal and VPN / IPSec pass-through
Configuration and Network Management Features
DHCP client and server for IP management
UPnP Internet Gateway Device (IGD) compliance
WEB for local or remote management
HTTP for firmware upgrade and configuration
Embedded syslog
Support TR-069 with parameters: DeviceInfo, ManagementServer, Time,
IPPingDiagonostic, etc
Note: The hardware and software specifications are subjected to change without notices.
71
X5671 User’s Guide
B1.
Product Warranty
XAVi Technologies warrants that the xDSL unit will be free from defects in material and
workmanship for a period of twelve (12) months from the date of shipment.
XAVi Technologies shall incur no liability under this warranty if
－ The allegedly defective goods are not returned prepaid to XAVi Technologies within
thirty (30) days of the discovery of the alleged defect and in accordance with XAVi
Technologies’ repair procedures; or
－ XAVi Technologies’ tests disclose that the alleged defect is not due to defects in
material or workmanship.
XAVi Technologies’ liability shall be limited to either repair or replacement of the defective
goods, at XAVi Technologies’ option.
XAVi Technologies MARKS NO EXPRESS OR IMPLIED WARRANTIES REGARDING
THE QUALITY, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE
BEYOND THOSE THAT APPEAR IN THE APPLICABLE USER’S DOCUMETATION.
XAVi SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INCIDENTAL, OR
PUNITIVE DAMAGE, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR
DAMAGES TO BUSINESS OR BUSINESS RELATIONS. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES.
72
X5671 User’s Guide
B2.
Warranty Repair
1. During the first three (3) months of ownership, XAVi Technologies will repair or
replace a defective product covered under warranty within twenty-four (24) hours of
receipt of the product. During the fourth (4th) through twelfth (12th) months of
ownership, XAVi Technologies will repair or replace a defective product covered
under warranty within ten (10) days of receipt of the product. The warranty period for
the replaced products shall be ninety (90) days or the remainder of the warranty
period of the original unit, whichever is greater. XAVi Technologies will ship surface
freight. Expedited freight is at customer’s expense.
2. The customer must return the defective product to XAVi Technologies within fourteen
(14) days after the request for replacement. If the defective product is not returned
within this time period, XAVi Technologies will bill the customer for the product at list
price.
B3.
Out-of-Warranty Repair
XAVi Technologies will either repair or, at its option, replace a defective product not
covered under warranty within ten (10) working days of its receipt. Repair charges are
available from the Repair Facility upon request. The warranty on a serviced product is
thirty (30) days measured from date of service. Out-of-warranty repair charges are
based upon the prices in effect at the time of return.
73
X5671 User’s Guide
FCC Part 15 Notice
Warning: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 to the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, used, and can
radiate radio frequency energy, and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is unlikely to cause harmful
interference. But if it does, the user will be required to correct the interference at his or
her own expense. The authority to operate this equipment is conditioned by the
requirement that no modifications will be made to the equipment unless XAVi
expressly approves the changes or modifications.
FCC Part 15 Notice with Wireless
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Warning: Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received including interference that may cause
undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
For product marketed in the USA/Canada, only channel 1 ~ 11 can be operated.
Selection of other channels is not possible
74
X5671 User’s Guide
FCC Part 68 Notice
This equipment complies with Part 68 of FCC Rules. On the base unit of this
equipment is a label that contains, among other information, the FCC Registration
Number and Ringer Equivalence Number (REN) for this equipment. IF REQUESTED,
THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.
The REN is useful to determine the quantity of devices you may connect to your
telephone line and still have all of those devices ring when your telephone number is
called. In most, but not all areas, the sum of the REN of all devices connected to one
line should not exceed five (5.0). To be certain of the number of devices you may
connect to you line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area.
If your equipment causes harm to the telephone network, the telephone company may
discontinue your service temporarily. If possible, they will notify you in advance. But if
advance notice is not practical, you will be notified as soon as possible. You will be
informed of your right to file a complaint with the FCC. Your telephone company may
make changes in it is facilities, equipment, operations or procedures that could affect
the proper functioning of your equipment. If they do, you will be notified in advance to
give you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, Please contact the following
address and phone number for information on obtaining service or repairs.
The telephone company may ask that you disconnect this equipment from the
network until the problem has been corrected or until you are sure that the equipment
is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company.
Connection to party lines is subject to state tariffs.
NOTICE: The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or an electronic device to send any message via a
telephone fax machine, unless such a message clearly contains in a margin at the top
or bottom of each transmitted page or on the first page of the transmission the
following information:
ü
The date and time of transmission
ü
Identification of either business, business entity or individual sending message
ü
Telephone number of either the sending machine, business entity or individual
Warning: Users should not attempt to make such connections themselves, but should
contact appropriate electric inspection authority, or electrician, as appropriate.
Do not use any other power adapter except the one that accompanies the unit. Use of other
adapter could result in damage to the unit. To prevent electronic shock, please do not open
the cover.
75
X5671 User’s Guide
UL Safety Regulations
ü
ü
ü
ü
ü
ü
Disconnect TNV circuit connector or before removing cover or equivalent.
Disconnect TNV circuit connector(s) before disconnecting power.
Do not use this product near water for example, near a bathtub, washbowl, and
kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightening.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Use only the power cord batteries indicated in this manual. Do not dispose of
batteries in a fire, as they may explode. Check with local codes for possible
special disposal instructions.
No. 26 AWG Telephone Line Cord shall either be provided with the equipment or shall
be described in the safety instruction. If fuse (F1) is not present, see the caution
statement listed below:
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA
Certified Telecommunication Line Cord.
76
X5671 User’s Guide
You can help us serve you better by sending us your comments and feedback. Listed
below are the addresses, telephone and fax numbers of our offices. You can also visit
us on the World Wide Web at www.xavi.com.tw for more information. We look forward
to hearing from you!
WORLD HEADQUARTER
XAVi Technologies Corporation
9F, No. 129 Hsing Te Road, Sanchung City
Taipei County 241, Taiwan
Tel: +886-2-2995-7953 Fax: +886-2-2995-7954
USA BRANCH OFFICE
53 Parker Irvine, CA 92618
Tel: +1-949-380-7550 Fax: +1-949-380-9204
S.AMERICA OFFICE
Tel: +55-12-8144-2972
EUROPEAN BRANCH OFFICE
Oehleckerring 6B, 22419 Hamburg, Germany
Tel: +49-40-514400-53 Fax: +49-40-514400-79
CHINA SUBSIDIARY
Room 401, Floor 4, #608 ZhaoJiaBang Road,
Shanghai, 200031
Tel: +86-21-6431-8800 Fax: +86-21-6431-7885
V1.0XA567107C
77

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2008:01:29 12:10:55Z
Creator Tool                    : pdfFactory http://www.pdffactory.com
Modify Date                     : 2008:09:25 15:20:57+08:00
Metadata Date                   : 2008:09:25 15:20:57+08:00
Format                          : application/pdf
Description                     : 20080129
Creator                         : shirley
Title                           : X5671 User manual
Producer                        : pdfFactory v1.57 (Windows XP Chinese)
Document ID                     : uuid:6a75620a-e987-4fe6-9c48-edb81c92317f
Instance ID                     : uuid:43dcb9e9-f3a8-4907-9091-006c6dfaaa85
Has XFA                         : No
Page Count                      : 82
Subject                         : 20080129
Author                          : shirley

EXIF Metadata provided by EXIF.tools

XAVi Technologies X5671 VDSL2/ADSL2+ Router User Manual X5671

XAVi Technologies Corp. VDSL2/ADSL2+ Router X5671

User Manual

FCC ID Filing: RYUX5671

Navigation menu

Namespaces

Views

Navigation