XAVi Technologies XW202M wireless mini PCI User Manual XW202M Manual

XAVi Technologies Corp. wireless mini PCI XW202M Manual

User Manual

Hardwar
e Specification
for
XW202M
RF
Module
Block Diagram:
Processor : Atheros AR2417 single chip integrated with the MAC/baseband/radio
Memory : Serial EEPROM:16K
Antenna Interface :1x2.4G Dipole Antenna.
I/O
Interface
:
minpci
Feature :
W
i
-fi
W
i
reless
Access
Point
IEEE802.11b/g
2.4G
Dipole
Antenna
Rx
Sensitivity
RX Sensitivity
T
est
Nam
e
Data
Rate
DUT
Measured
11g
RX
Sensitivity
6Mbps -88
RX
Sensitivity
36Mbps -73
RX
Sensitivity
48Mbps -70
RX
Sensitivity
54Mbps -68
11b
RX
Sensitivity
1Mbps -90
RX
Sensitivity
2Mbps -87
RX
Sensitivity
5.5Mbps -86
RX
Sensitivity
11Mbps -85
TX RF POWER
Transm
it
Power
T
est
Nam
e
Data
Rate
DUT
Measured
11g
Transm
it
power
6Mbps
17
(+1.5/-1.5)
dBm
Transm
it
power
36Mbps
16
(+1.5/-1.5)
dBm
Transm
it
power
48Mbps
15
(+1.5/-1.5)
dBm
Transm
it
power
54Mbps
14
(+1.5/-1.5)
dBm
11b
Transm
it
power
1Mbps
17
(+1.5/-1.5)
dBm
Transm
it
power
2Mbps
17
(+1.5/-1.5)
dBm
Transm
it
power
5.5Mbps
17
(+1.5/-1.5)
dBm
Transm
it
power
11Mbps
17
(+1.5/-1.5)
dBm
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance
requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host this
module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to
operate this equipment.
USERS
MANUAL
OF
THE
END
PRODUCT:
In
the
users
manual
of
the
end
product,
the
end
user
has
t
o
be
informed
t
o
keep
at
least
20cm
separation
with
the
antenna
while
this
end
product
is
installed
and
operated.
The
end
user
has
to
be
informed
that
t
he
FCC
radio-frequency
exposure
guidelines
for
an
uncontrolled
environment
can
be
satisfied.
The
end
user
has
to
also
be
informed
that
any
changes
or
modifications
no
t
expressly
approved
by
the
manufacturer
could
void
the
user's
authority
t
o
operate
this
equipment.
If
the
size
of
the
end
product
is
smaller
than
8x10cm,
then
additional
FCC
part
15.19
statement
is
required
to
be
available
in
the
users
manual:
This
device
complies
with
Part
15
of
FCC
rules.
Operation
is
subject
to
the
following
t
wo
conditions:
(1)
this
device may
not
cause
harmful
interference
and
(2)
this
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
LABEL
OF
THE
END
PRODUCT
:
The
final
end
product
must
be
labeled
in
a
visible
area
wi
t
h
the
following
"
Contains
TX
FCC
ID:
RYUXW202M
". If
the
size
of
the end
product
is
larger
than
8x10cm,
then
the
following
FCC
part
15.19
statement
has
to
also
be
available
on
the
labe
l:
This
device
complies
with
Part
15
of
FCC
rules.
Operation
is
subject
to
the
following
t
wo
conditions:
(1)
this
device
may
no
t
cause
harmful
interference
and
(2)
this
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.

Navigation menu