XPLORER BKF DEUS head phone User Manual 002

XPLORER DEUS head phone 002

User Manual

USER'S MANUAL V 1.0
Page 60Page 02Page 04 Page 05Page 06Page 07Page 08Page 09Page 10Page 11Page 12Page 13Page 15Page 15Page 16Page 17Page 18Page 18Page 20Page 21Page 22Page 23Page 24Page 25Page 26Page 26Page 26Page 27Page 2701 CORDLESS HEADPHONES Menu —Discrimination-Sensitivity-Ground Frequency-Tones-Volume-Coil Pairing with a new coil —Factory Programmes —Replacement of the backphone —POWER SUPPLY - BATTERIES Low battery lights —Battery life —Charging time and charging progress —Charge — Battery durability —Replacement —Precautions —EXPERT Multi-Tones —Pitch —Multi-Tones, thresholds and tones —TX Power —Frequency shift —Silencer —Multi-Notch —Page 29 / 30Page 30Page 31Page 31Page 32Page 32Page 32Page 33Page 34Page 34Page 35 Page 36Page 36Page 37Page 38Page 39Page 39Page 40Page 41 / 42Page 43Page 44 / 45Page 46Page 47Page 48Page 49Page 50 / 51Page 52 / 53Page 54 / 55Page 56 / 57Page 58QUICK START —TECHNICAL INTRODUCTION —LIST OF PARTS —ASSEMBLY —USE Remote control —Factory programs, Description —Starting up — MENU Discrimination —Sensitivity —Frequency —Iron Level —Reactivity —Audio Response —Notch —GROUND General —Manual Mode —Pumping Mode —Tracking Mode —Beach Mode —NONE MOTION — OPTION Programmes —Coil —Pairing with a new coil —Conguration —Speakers —Back light —Contrast —Clock setting —Update — PRACTICAL INFORMATION —PRECAUTIONS FOR USE —TROUBLESHOOTING AND SOLUTIONS —SPECIFICATIONS —ACCESSORIES —SPARE PARTS —RECOMMENDATIONS / LAW —FACTORY PROGRAMMES —YOUR SETTINGS —MENU STRUCTURE —DECLARATION OF CONFORMITY —WARRANTY —TABLE OF CONTENTS
CONGRATULATIONS ON THE PURCHASE OF YOUR XP METAL DETECTOR AND WELCOME TO THE WORLD OF RESEARCH AND EXPLORATION! ®, the rst fully wireless detectorYou have invested in a high-tech detector capable of exceptional performance, which was designed and developed in France. You are therefore helping our Company to further researchin the eld of metal detecting and we thank you for your contribution.02Dēus is innovative in terms of metal detector design as it oers an architecture based on three elements communicating via a digital radio link. In this new design the coil, remote control and audio headphones have each been made independent through the integration of very compact, high-capacity lithium batteries. An ultra-miniature electronic circuit, incorporated in the search coil, digitises and analyses the signals. Data is then sent to the headphones and remote control in real time via a digital radio link. With this method, the signal is processed at source and not conveyed via a wire link, which greatly improves data quality. Incorporating components from leading-edge technologies such as scientic instrumentation has enabled us to produce a powerful, rapid, lightweight, compact and fully controllable digital detector. Whether you are an experienced user or a beginner, Dēus lets you decide whether or not to modify any of its settings. Powerful pre-congured factory programmes enable all users to get started immediately, while expert detectorists can choose more advanced parameters via the intuitive interface. What is described in this manual as the "Remote Control" is in fact the user interface, known as the ‘control box’ on conventional detectors. It enables the detector’s many functions to be precisely adjusted via a graphical interface. It can also receive programme updates (via internet) through its USB socket.
Dēus is also exceptional in being able to function without the remote control, with just the coil and the wireless headphones, for an even more compact, lightweight conguration (just 875 g)! Like the remote control, the headphones contain all the components needed for detection, they are a genuine control unit in themselves, but on an ultra-miniature scale. They take over in the absence of the remote control for adjusting the detector settings.With the headphones you can turn Dēus on and o, change the main detection settings such as sensitivity, discrimination, ground balance, tone, frequency (4 kHz, 8 kHz, 12 kHz, 18 kHz), volume, etc. as well as selecting the factory programmes or those previously congured with the remote control! Performance is identical whether you are searching with or without the remote control! Lastly, the new patented* XP stem has the combined advantages of an S-shaped stem and a straight telescopic stem. It enables you to deploy or fold away the device in just a few seconds, and to change the coil in an instant. Its user-friendly design ensures comfort and convenience for the user: length adjustable by millimetre increments, improved operating angle and shaped rubber handle for a rm, controlled grip. So now you’re ready for a new adventure! *Patent application underway 03TECHNICAL INTRODUCTION continued ...
One assembled fully telescopic stemOne set of wireless headphoneswith storage caseOne 22.5 cm search coil with coil coverOne user interface (remote control)with case One connection cable: USB / one mini-B plugOne connection cable: USB / three mini-B plugsOne power supply transformer-chargerOne connection clamp for recharging the coilOne set of fastenings (2 screws, 2 wing nuts,1 washer, 1 spacing washer)04LIST OF PARTS The box for your Dēus metal detector contains the following parts:
053 positionsFitting the coil on the stem Insert the single rubber washer in the lower shaft. Line up the stem with the coil and t the two parts together.Install bolt and nut.
Access to (Ground Balance) Manual / Pumping / Beach / Tracking -ON/OFF Access to menu Conguration / Programs /Coil / Factory programs Decrease valuesChange programmeUSB connection for charging the lithium battery or for updating the software via internet Increase valuesChange programmeNone motion mode (Pinpoint)3.5 plug: 3.5mm audio output jackMENUMENUG.B.OPTIONOPTION1 - BASIC 1 MENU EXPERTNOTCH SENS. FREQ.DISCRI.Battery levelof coil and remote control(displayed alternately)Name of active programmeChange programme with TimeAnalog scale of target conductivity Digital scale of target conductivity, from 0 to 99 Detection frequency used 4 - 8 - 12 - 18 kHz The ground mineralisation index (level measured constantly by Dēus for information) The actual level of ground eect corrections (adjustment underway)Representative curve for the detector’sactive settings relating to sensitivity,selectivity and powerG.B.Reminds you of the target conductivity index to help you optimise your settingsValid and return to main menuTo scroll through the menuAccess to expert menu Access toDISCRI - SENS - FREQ .../Example of secondary pageFast 06Slow and deep
From the main menu navigate with to change the programmes1 - BASIC 12 - GM POWER3 - DEUS FAST4 - PITCH5 - G-MAXX6 - RELIC7 - WET BEACH8 - ALL METAL9 - BASIC 2 General use (12 kHz).Similar settings to the XP Gold Maxx Power detector, powerful and fast.Faster than the Gold Maxx Power with small targets on iron-infested ground.Responsive pitch that varies in frequency and amplitude according to the signal’s strength, same speed as the Gold Maxx Power.Similar settings to those of the XP G-Maxx1 detector, medium speed, particularly eective for large masses and highly conductive coins.Slower than the G-Maxx1, adapted for large, deep masses in relatively uncontaminated ground. Tuned to operate more eectively on wet beaches, although in situ adjustments are needed for the ground eect, either by pumping or manually (pg 17).Suitable for deep searching for all targets, a motion all metals mode. Ease of operation with settings that oer greater stability, perfect for starting out while avoiding false signals. (pg 50/51)Name of the active programmeMENU G.B.OPTION1 - BASIC 1 07
To switch o Dēus Hold down Power for two seconds on the remote control. Press left- and right-hand buttons on the headphones. -YESNODISCSENSGNDFREQTONEVOLCOILAfter charging your device. (pg 33)Switch on the remote controlCoil far from metal surfaces Switch on the headphones Validate or not the use of the loudspeaker - Do not switch on Dēus when the coil is near a metal surface, inside a car, or when the stem has been folded away, as this may interfere with calibration and lead to abnormal performance. If this should occur, switch Dēus o and move away from any metal masses before switching it on again.Nevertheless, this does not represent any risk to the equipment or its electronics! By default you begin by using the 1 - BASIC 1 factory programme which is suitable for general use.If you wish to test one of the 9 other factory programmes, simply scroll through them with 08The LED on the coil gives 20 long, successive ashes to indicate that it is waking up and recalibrating.Once recalibration is complete, the coil becomes operational and its LED ashes every second.When the coil is on standby, its LED ashes every 4 seconds, whereas when it is on it ashes every second.
Adjust the Discrimination level (from 0 to 99) with Exit with to return to the main menu.Discrimination enables undesirable targets to be rejected by raising or lowering a threshold below which certain metals are dierentiated. The conductivity scale (0 to 99) for metal targets shown below will help you better understand the discrimination range and its limits, and see how it corresponds to the digital display of target conductivity on the remote control main menu.Increasing the discrimination value enables you to gradually reject any target whose conductivity is lower than the setting. For example, if you tune the discrimination level to 10, you will reject iron with a value of between 0 and 10. If you tune it to 40 you will also eliminate small pieces of aluminium foil whose conductivity is less than 40.If you wish to reject other rubbish with higher conductivity, such as pull tabs from aluminium drinks cans, lead shot or copper hunting cartridges (whose conductivity is 60-75), you must also be prepared to accept the elimination of certain good metals with similar conductivity.If you are particularly bothered by contamination registering as highly conductive on the digital screen, and you still wish to reject it, it is betterto do so using the NOTCH rejection setting.Conguring the main detection settings. Press menu Scroll through the menu by pressing MENUMENU G.B.OPTION1 - BASIC 1 Coke Foil Bronze coins(medium size) Large silver andcopper coinsIronNailsSmall targetsSmall jewellery, leadsFine coinsPoor alloys Small pure silver coins MENU EXPERTNOTCH SENS. FREQ.DISC090 10 20 30 40 50 60 70 80 90 99
MENU EXPERTDISC FREQ. IRON VOL. SENS Adjust the Sensitivity level (from 0 to 99) with Exit withSensitivity is often simplistically described as the setting which adjusts the device’s power level. However this is incorrect. As its name indicates, it actually determines the device’s sensitivity level. It reacts after receiving a signal via the receiver coil. Nevertheless, the results are somewhat similar in practice, as increasing a device’s sensitivity enables it to detect the presence of more distant targets. However it must be noted that this setting has no eect on the power emitted.The most commonly used sensitivity levels range from 70 to 90. It may be necessary to reduce the level if there is too much interference, as is often the case near overhead or buried power lines, fences, radio-relay stations, mobile telephones, computers, televisions, etc.Do not test your device in your home as there is considerable electromagnetic and metal interference in urban environments.Two alternatives involve selecting a low level of discrimination, between 5 and 10, then using either:1/ The digital target display to more or less visually discriminate a target category.2/ The Multi-tone mode to discriminate undesirable targets using a selected audio tone.In both cases the decision then lies with you on whether or not to dig. Depending on the frequency setting used, a target’s conductivity is perceived dierently by the detector. The digital conductivity display may therefore vary depending on the frequency. The 0 to 10 range relates to the rejection of iron. To achieve greater precision in this range there is a digit after the decimal point (from 2.1 to 9.9),which in eect gives you 82 dierent levels for iron. In several menus, particularly at the top right of the Discrimination screen, a reminder of the target conductivity index is displayed, which helps you when adjusting the discrimination level.MENU EXPERTNOTCH SENS. FREQ.DISC10DISCRIMINATION continued...
Scroll through the frequencies with Exit with Dēus gives you the choice of four detection frequencies (4 kHz, 8 kHz, 12 kHz and 18 kHz) which cover most detection needs. They enable you to adapt your research more closely to the characteristics of the ground and the targets to be detected.MENU EXPERTSENS. IRON VOL.REACTIVITY FREQ.KHZSmall coins made from any alloy (gold, silver, copper, etc.) and bigger but very ne coins, low conductivity gold coins, lead, rings, sheet metal, aluminium foil.Small objects can be found even on mineralised ground contaminated with iron. Discriminates (distinguishes) coke more easily.More unstable on non-mineralised and moist ground.Here is a non-exhaustive list of the most likely targets that may be detected according to the frequency:4 kHz8 kHz12 kHz18 kHzLarge, mainly ferrous and non-ferrous masses.Coins of sucient conductivity and size. All other medium or relatively small targets in non-mineralised ground relatively uncontaminated by iron.Good for ferrous masses and militaria.General use.Coins and large masses, militaria.Medium and small targets in low-mineralised ground.General use, small coins.Coins of all sizes in medium to highly mineralised ground.11
Remember that generally speaking, all frequencies can detect all kinds of targets, so for example a frequency of 4 kHz will detect a very small target and a frequency of 18 kHz will detect a large, deep mass.However, the 18 kHz frequency will lead you to discover a relatively higher number of small targets that cannot compare with that achieved with a frequency of 4 kHz. Similarly, sometimes the 18 kHz frequency can be slightly less eective with a large mass.If you are just starting out, the 8 kHz frequency is a good compromise for general use. On a wet beach the 18 kHz frequency will be better at nding small gold jewellery such as chain necklaces and bracelets that are usually so dicult to detect.MENU FREQ. REACTIVITYAUDIO RESP. IRON VO. Adjust the Iron Volume (from 0 to 5) with Exit with- At 0 the low-pitched tone is cut o.- At 5 the low-pitched tone will have a sound level equivalent to other medium- or high-pitched tones. 12You have the option of controlling the sound volume of the low-pitched tone which generally corresponds to iron. Depending on the circumstances, this enables more attention to be paid to other sounds, by reducing those generated by iron.On the other hand, some users prefer that the low-pitched signals from iron are more audible, as they know that good targets at the detector’s range limit in mineralised ground sometimes generate low amplitude, low-pitched sounds. If the discrimination threshold is too low, 0 or 2 for example, most iron will generate not low- but medium-pitched tones, as you will practically be in the All Metals mode. In this case, the iron level setting will not be of much use.
Adjust the Reactivity from 0 to 5 with Exit withEXPERTMENU IRON VOL. AUDIO RESP.NOTCH REACTIV.Large masses and coins, in ground uncontaminated by iron.Large masses and coins, in ground with little iron contamination, and general use.General use, and mineralised soils contaminated with iron.Dicult soils contaminated with iron, hot rocks, etc. Very dicult soils, highly contaminated with iron and hot rocks, sensitivity to small targets. 0 1 2 3 4/5Most likely nds with the recommended settings are as follows:13Reactivity is a vital setting that determines the detector’s performance in terms of speed of analysis and selectivity. If a soil contains a great deal of iron, hot rocks or other mineralised debris, soil penetration is generally reduced, as is a detector’s ability to identify targets similar to iron.In these conditions, Dēus enables you to select a high degree of reactivity which will help you speed up the analysis of signals.On the other hand, if the ground is "clean", it is better to reduce the reactivity and sweep more slowly, in order to be more sensitive to deep masses and obtain more thorough penetration. Users familiar with the Gold Maxx Power have already had a foretaste of the Reactivity (recovery speed) of XP’s detectors. And even though Dēus is a particularly fast and selective detector, you now have the option of adjusting the reactivity setting to make it even more selective! By way of example, and to help you better understand the reactivity levels available, you should note that the reactivity of most detectors on the market is generally only equivalent to level 1 of the Dēus. This is true, for instance, of the Gold Maxx and earlier XP models. The Gold Maxx Power has a reactivity equivalent to level 2 of the Dēus. Higher reactivity levels (3, 4, 5) enable the detector to tolerate fast sweeps better.
ExamplePassing the coil over an iron object close to the surface then over a good metal target (ring).With a low Reactivity level, the iron is detected for a longer duration, to the extent that it completely hides the ring. A high Reactivity level enables you to distinguish the ring completely from the iron.The audio signal fully indicates the target.Full soundShort soundNo sound01234514In terms of pure performance, the greatest detection ranges are obtained with low reactivity levels. However, you will nd more targets on dicult ground with medium or high reactivity levels. So do not just rely on performance in optimal conditions.Depending on the reactivity level, you will notice that the length of the audio signal varies when it passes over a target:Low reactivity (0, 1) = long sound High reactivity (3, 4, 5) = short soundEvidently the length of any false signals (the crackling of iron for example) will vary proportionately as well.You are therefore advised not to constantly change the reactivity level, as this may interfere with your ability to distinguish good and bad sounds.With a medium Reactivity level, you begin detecting the ring.The audio signal partially indicates the target.
The Audio Curve enables you to amplify the sound volume of distant targets and therefore to be more alert to them. It gives the sensation of greater power, however it does not provide any additional depth as this setting only aects the sound curve (the dynamic range of sounds). By amplifying small signals you will also be amplifying small spurious false signals. By increasing the sound response you will compress the dynamic range and thus reduce the appreciation of a target’s distance.Notch complements discrimination: it enables a "window" of targets to be rejected whereas discrimination rejects all targets below a selected threshold. For example, if you detect a redundant, undesirable target in the ground, you can decide just to reject the corresponding conductivity group and continue to detect targets whose conductivity is higher and lower than those in this group. If the reference target has a conductivity of 37, adjust the Notch value to 34-40 using All targets whose conductivity is between 34 and 40 will then be silenced. Exit with By default, the width of the rejection window is 6 points. EXPERTMENU AUDIO RESP.DISCSENS NOTCH Adjust the Audio Response from 0 to 5 with Exit withMENU REACTIVITY NOTCHDISC AUDIO R.Distance to targetAudio Level54321015AUDIO RESPONSE
The dierent levels of soil mineralisation you encounter when prospecting can sometimes aect the performance of your detector. For example, this may be due to natural magnetic mineralisation such as iron oxide, hot rocks and magnetite, or sporadic mineralisation from sites of former human settlement (also magnetic): hearths, pottery, hot rocks, slag, etc. At the seashore this may also involve mineralisation ranging from magnetic grade (black sand) to electrical conductor grade (salt water) depending on the beach or region. If you are an experienced detectorist you may wish to optimise your searches to achieve better penetration in some of these mineralised soils. In magnetic ground with relatively uniform mineralisation, a setting which is adjusted according to the ground eect will improve penetration by reducing the amplitude of the ground signals sent back by the receiver circuits. This ‘adapted setting’ involves adjusting your ground balance value to the average value of the ground being detected, while adding 1 so as not to hear the ground signals as much. The tracking and pumping modes do this automatically if the ground conditions allow it. Attention: As the ground balance setting is the one requiring the most experience of the ground, we recommend that you read this chapter carefully and use the dierent ground balance modes carefully, while acquiring your own experience of the ground.By default, remain in manual mode at level 90 on inland ground and on dry beach sand. If the ground is not mineralised there is no need to adjust your ground balance to a level other than 90: since the ground does not send back any signicant spurious echo the performance will be optimal even at level 90 and you will reduce interference resulting from knocks to the coil.On the main menu, two values are permanently displayed:MENU G.B.OPTION1 - BASIC 1 16The ground mineralisation index (level measured constantly by Dēus for information).The actual level of ground eect corrections (adjustment underway).General features
Go to Pumping with you obtain the display G.B OK Exit withG.B. TRACKING PUMPINGBEACH MANUALSTART Go to Manual with Adjust with Exit withG.B. MANUAL BEACHTRACKING PUMPINGSTARTSOL MANUAL BEACHTRACKINGIN PROGRESS G.B OK Press Ground4 modes are available:MANUAL - PUMPING - TRACKING - BEACH (ON / OFF) G.B.17You can manually adjust the ground rejection levels from 60 to 95 (Beach 90 is the default level, it is the most common level which enables you to reject all magnetic minerals found in the ground.By reducing G.B. towards 87 you will begin detecting hot rocks, and knocks to the coil may result in false signals. Even lower, between 75/85, pottery and the ground itself will begin interfering with your device. suggest that you limit yourself to a Ground Balance level of 90, which is the default setting, and is the most stable reference level recommended for inland ground. Levels lower than 90 will result in increasing instability..
Go to Tracking with Exit withG.B FAIL15 cm (6")~MANUALPUMPINGG.B. BEACH TRACKINGIN PROGRESSG.B. MANUAL BEACHTRACKINGG.B FAIL18Pumping is a semi-automatic process which allows you to adjust the ground balance in a zone that you have determined as being representative of the mean level of the ground being prospected.Henceforth, the measured value of the ground is entered in memory and used as the new active ground balance value. If this value is unsuitable, or if it generates too much instability, you can to modify it by, for instance, adding several extra rejection points. If a metal target is detected while you are pumping, Dēus will recognise this and display the message It will then retain the previous ground balance value.This problem is generally caused by iron being present. If this is the case then move to another location and restart the pumping mode. In low- or non-mineralised ground, there is no need to adjust the ground balance and you are advised to remain on 90 for greater stability. extracted signals to determine the mean value on a continual basis. This mode may be useful in soils with relatively uniform mineralisation, and where the mineralisation varies gradually from zone to zone, which is often the case in naturally mineralised ground. In this case, Dēus automatically readjusts the ground balance according to the most recent value measured.However, in ground where mineralisation has resulted from human presence (ancient settlements, for example) this mode may be unsuitable due to the disparity in the ground events.
19Indeed, within the same sweep of just one metre, a considerable variety of ground events may be encountered, ranging from one extreme to the other (values between 70 and 90): hot rocks, brick, slag, pottery interspersed with soil that is neutral or characterised by diverse mineralisation. This may be to such an extent that any mean value would be meaningless. You must then determine an acceptable level of rejection for the ground based on your own experience of the site, your detection methods and the interference that you are prepared to tolerate. This mode is not available in Beach mode, in wet areas, as the Pumping mode is more eective. Low ground balance levels also generate the clearest signals on certain irons that are already dicult to eliminate. With some digital detectors on the market, you will note that when the ground balance settings are low – either in Manual, Pumping or Tracking mode – hot rocks do not register, as they have been somewhat ‘notched’ or inhibited. This trick gives you good stability regardless of the ground rejection level, however it also deprives you of the benets of a well-adjusted ground balance, and worse, gives you the impression that your settings are well congured.Very often the deepest targets in magnetic soil are identied with a signature similar to that of hot rocks, and are therefore detected poorly with this kind of device (as they are ‘notched’).Dēus on the contrary gives you full control over the ground settings. When you lower the ground balance (87-85-82 etc.) you fully accept hot rocks, which is the only way to obtain real gains in terms of penetration on certain magnetic soils.
Go to Beach with Choose YES (00-30) Activates calculation of the ground balance on the zone corresponding to highly saline wet ground, so as to reduce interference caused by conducting salt water. After selecting Beach ON, you need to adjust the ground balance manually or by pumping on the wet zone concerned, in order to cancel out the ground signal. Go to or go to withPress and pump the coil on the ground several times until you obtain the displayIn Manual Mode, adjust it from 00 to 30 with Exit with In wet zones (salt water), it is important to sweep while keeping the coil parallel to the ground, yet not touching it. In wet zones you can select the Wet Beach factory programme.PUMPINGG.B. BEACHPUMPING MANUAL BEACH YESSTARTG.B. BEACH MANUAL BEACH PUMPINGSTART20To improve stability on wet beach (salt water):Reduce Audio Response (0-1)Increase Reactivity (4-5)Power: Level 1 maximum. Sensitivity: (70-85). G.B OK
Place the coil at a height of approximately 5 cm (2") above the ground on a zone free of metal targets Press (Pinpoint) The sound threshold is calibrated and you are switched to none motion mode. Calibration of the threshold can be repeated at any time by pressing the Pinpoint button again. If you are continually searching in none motion mode you will need to recalibrate this threshold at regular intervals.The stability and sensitivity of the none motion mode will depend on how eectively the detector has been calibrated:If you recalibrate the threshold with the coil too far from the ground, then sensitivity will be lower but the device will be more stable. If you recalibrate the threshold with the coil too close to the ground, then its sensitivity in none motion mode will be high but the device will be unstable on the ground. The ground mineralisation should help you determine the best height for obtaining the desired level of sensitivity. In Motion Mode, very rapid crossed sweeps are usually sucient to locate a target. Dēus is designed to operate most of the time in Motion Mode, which means that a metal target will only be detected if the detector’s coil is moving. However, the detector can also be operated in Pin Point mode, if required, which means that it will detect even if the coil is motionless above a target.In modern detectors, none motion mode is most often used to locate a target more precisely (pinpointing).However this mode is also very useful for detecting the presence of metal in cramped locations, where there is not enough space to swing the coil, or if there is too much interfering metal around the target. For example, locating hiding places inside houses, cellars and walls.None motion mode is also widely used in the construction industry to locate metal pipes, as it enables them to be continually tracked. PINPOINT 21Animated test card depending on the signal’s amplitude Press the return button to go back to the home pageUsed to access the none motion (Pinpoint) menu and/or update the threshold5 cm (2")~
Press to scroll through the menu and stop on the programme you wish to save, then press Scroll with and stop on Press to save. Choose either YES or NO to conrm. Press X2 to return to the main menu. Press to scroll through the menu and stop on the programme you wish to modify, then press Press and stop on Press and scroll withAnd to advance to the next data entry zoneOr to delete the previous character.Press and X2 to return to the main menu. Press Choose with then pressModify the name of a programme2OPTIONPROGRAMSELECTOPTION CONFIGURATION COILPROGRAMSELECTOPTIONSave a modied programmeSELECTSELECTOPTIONVALIDThese enable you to save your settings, create new programmes and congure your equipment’s basic parameters.Listed here are the nine detection programmes which were pre-congured at the factory.You can modify the name of a programme, save modications made to a programme or restore a factory programme.22PROGRAMRESTORESAVE EDIT NAMESELECTPROGRAM EDIT NAME RESTORE SAVESELECT SAVE EDIT NAME
Press Choose with then press Switch on the headphones close to the remote control. On the remote control, press to scroll through the list of available coils and stop on the one you wish to activate. This coil automatically becomes active within 4 seconds, while the previous coil reverts to standby mode. Press X2 to return to the main menu. If you switch on the headphones after changing the coil via the remote control, the headphones will not automatically register this change. You will therefore need to change the coil manually via the headphones. (pg 24)2OPTION2COILSELECTOPTION PROGRAM CONFIGURATION COILSELECTRestore a programme COIL2-COIL 34 CM (13") 1-COIL 22.5 CM (9")OPTIONExample23PROGRAM SAVE EDIT NAME RESTORESELECT Press to scroll through the menu and stop on theprogramme you wish to restore, then press Scroll with and stop on Press to restore. Choose either YES or NO to conrm. Press X2 to return to the main menu.SELECT RESTOREOPTIONWhen rst purchased, Dēus is only congured to operate with its original coil.If you have one or more optional coils which have already been paired (pg 24), you can select which one you want to use for your detection session, from the list in the menu.
Press Choose with then press Sélect an unused slot ( -------) with then press Choose with then press At the point where the cursor is ashing, scroll through the characters using to make your choice. Press to advance to the next character. Once the name of the new coil has been entered (e.g: "34 cm Coil"), Press OPTION PROGRAM CONFIGURATION COILSELECT2OPTIONOPTIONEDIT NAME SELECTSELECT VALID Entering the nameIf you purchase an additional coil, you need to pair it with the remote control and the headphones the rst time you use it, to enable Dēus to recognise and communicate with it. You can then switch between coils just with a simple click via the remote control.To pair a new coil you have to give it a name (e.g: "34cm Coil") and enter its serial number in the remote control and headphones.The serial number is printed on the coil and is sometimes found on the invoice as well.Before you pair a new coil, turn on the headphones and remote control.Check that they both work correctly with your original coil.Keep the headphones, remote control and also the new coil close to each other and follow the following steps:COIL EDIT SERIAL NUMBER EDIT NAMESELECTCOIL1- COIL 22.5CM (9") 2-----------------OPTION Pairing the remote control and the headphones with a new coil24COILEDIT NAME 34 CM COIL
Entering the serial number At the point where the cursor is ashing, scroll through the characters. using and press to advance to the next digit. At the sixth digit press then X2 to return to the main menu. The remote control now adds this new coil to its list, then transfers the updated list to the headphones. VALIDif the headphones do not recognise this coil, for example because they were switched o while the serial number was being entered in the remote control, You then have 2 options to pair it:1: Turn on the headphones and the remote control with the previous coil (for example the original one). The list of coils from the remote control will be sent automatically to the headphones.2: enter this new coil’s serial number manually in the headphones as well (pg 30).A coil’s serial number is unique. The headphones or remote control cannot function with a coil if the number entered does not correspond to the actual serial number printed on the coil.This allows you to modify the remote control’s general technical settings. Press Choose with then press2OPTIONCONFIGURATIONSELECTOPTION PROGRAMCOILCONFIGURATIONSELECT25EDIT SERIAL NUMBER 1-----EDIT SERIAL NUMBER 123456
To improve readability in all lighting conditions you can adjust the contrast of the display. Choose with Press to change the contrast value. Press x2 to return to the main menu.The remote control screen has a backlighting function which comes on as soon as any button is pressed and goes o automatically after a certain length of time. You can dene this time in seconds: OFF - 3s - 10s - 60s -120s - ON (permanent) Choose with Press to change the duration of the backlighting. Press x2 to return to the main menu. Enables the remote control’s loudspeaker to be activated or deactivated. Choose with Press and choose ON or OFF Press x2 to return to the main menu. You can leave the backlighting on permanently (ON) as this function uses very little power and only aects the remote control’s battery life by about 10%.CONFIGURATION UPDATE BACKLIGHTCONTRAST SPEAKER. OFFCONFIGURATION SPEAKER CONTRASTCLOCK SETTING BACKLIG. 3sCONFIGURATION BACKLIGHT CLOCK SETTINGUPDATE CONTRAS. 3Duration of backlighting SPEAKER CONTRASLoudspeakerContrast 26 BACKLIG
The software can be updated via the Dēus USB interface and an internet connection.Full information is available on our website: www.xpmetaldetectors.com/deus/update Choose with Press adjust the time. Press x2 to return to the main menu.CLOCK STimeUpdatesThis changes the time that is displayed on the main menu.-1 - BASIC 1 CONFIGURATION CONTRAST UPDATE SPEAKERCLOCK S.Use the single USB cable.27MENU G.BOPTION
Control padsIncrease / decrease valuesTo switch ON : Press To switch OFF : Press simultaneously and Displayed : Coil battery level Not displayed : Headphones battery level Used to scroll through the detection menus and their setting values: DISC --------------------- SENS -------------------------- GND ------------------------------ FREQ ------------------------- TONE ---------------------- VOL ----------------------- COIL ------------------------ P1 to P9 -------- USB/mini-B charging connectionDISCSENSGNDFREQTONEVOLCOILIndicates the setting value or the number of the factory programme P1, P2, etcIndicates the battery charge level of the coil and the headphones (alternates every 4 seconds) Indicates that the radio link with the coil is active Discrimination Sensitivity Ground Frequency Tone number Audio volume Selected coil Factory programmes28
Menus accessed via the headphones have the same range of settings as the remote control.Remote control ON: Only the volume control can be adjusted.Remote control OFF: All settings can be adjusted.Press to access the dierent menus DISC Discrimination: 0-99 (pg 09).Adjusts with A ashing digit represents a digit after the decimal point. SENS Sensitivity: 0-99 (pg10). Adjusts with FREQ Choice of frequency used: 4, 8, 12, 18kHz (pg 11).Change with TONE Choice of number of tones: 2, 3, 4 tons, P (PITCH) (pg 36).Change with VOL Adjusts sound volume in headphones: 0-9.Adjusts with COIL Choice of coil used when several are available.The coils are numbered according to the order in which they were entered: 01 = Original coil02= Optional coil 1 03= Optional coil 2, etc.FREQDISCSENSGNDFREQTONEVOLCOILSENSCOILGNDTONEVOL29 GND Ground balance (pg 17).60-95: (inland ground)0-30: (Only with program N°7, for beach, wet zone) Adjusts with
When delivered, the headphones and remote control have already been paired with the original coil, so no action is required on your part.However, if you purchase an additional coil, before using it for the rst time you need to pair it with the remote control and the headphones, to enable it to recognise and communicate with them.You can then change coils with a simple click using the remote control (pg 23) or your headphones (pg 30).If you leave the headphones switched on when you pair the remote control with a new coil, they are also paired with this new coil, which is then added automatically to the list in the headphones menu (pg 24).If you do not have the remote control, or in the event of a problem, you can manually pair the headphones with a new coil. To do this you need the serial number of the coil to be paired: Press until you reach COIL Choose a free slot with for example 02 (01 is already assigned to the original coil).If this coil has already been paired with the remote control, ensure you choose the same slot number in the headphones. Press for 2 seconds to switch to serial number entry mode. With enter the rst digit of the serial number then validate it with continuedIf you are detecting with the remote control and you use it to change to a new coil, the headphones will automatically register this change (if they are switched on). Otherwise it can be done manually with this menu.Always leave the headphones switched on when you are changing the coil via the remote control, otherwise they will not register the change and will remain connected to the previous coil. If this should occur, use the remote control to return to the previous coil (with the headphones switched on) and switch to the new coil again to re-register it with the headphones.Remember that before you can use a new coil for the rst time, you need to enter its serial number in the headphones and remote control (pg 24/30).COIL Pairing the Headphones with a new Coil30
With enter the second digit then validate it with With enter the third digit then validate it with Continue in this way until you reach the sixth digit.The new coil is now operational in this slot and should become active. Choice of one of the 9 pre-congured factory programmes. Press and go to P1/9 screen. Scroll with and choose the programme number.The programmes are identical to those in the remote control and are numbered in the same way from 1 to 9.e.g. P3 headphone = factory programme 3 in the remote control.Programme 7 is the remote control’s wet beach mode and is designed to be used in the wet zone of a beach. Its ground balance settings range from 0 to 30, not 60 to 95 like the other settings. Each time that the remote control is switched on next to its accompanying headphones, all the remote control’s settings are loaded into the headphones, which then store them in memory even when switched o. This only works if the headphones and remote control have both been paired and are using the same (serial number) coil.The earphone of the wireless headphones contains all the electronics and the lithium battery, it represents your headphone’s brain! (ref: D091).Fitted on a sliding support, it has the advantage of being able to disconnect from the backphone with a single click.This backphone is an inexpensive wearing part that can easily be replaced by any of our resellers (ref: D096).A coil’s serial number is unique. Dēus cannot use a coil if the number entered does not correspond to the actual serial number printed on the coil (and sometimes appearing on the invoice as well).Programs P1 to P9Replacement of the backphone31
The remote control alternately displays :The symbol which indicates the coil’s charge level. The symbol which indicates its own charge level.If you only use the headphones without the remote control, you will also need to know the coil’s charge level. Displayed = coil’s charge level. Not displayed = headphone's charge level.HEADPHONES: 20 hours / REMOTE CONTROL: 20 hours / COIL :± 10 hoursCHARGING TIMEDISCSENSGNDFREQTONEVOLCOILThe search coil’s battery life may vary depending on the modes used. The table below shows battery life according to frequency and power selected. Dēus is regulated in such a way that avoids any deterioration in performance even when the battery level is lower!100% charged 60% charged 30% chargedMay vary depending on the age of the battery.DISCSENSGNDFREQTONEVOLCOILFrequency 4 kHzFrequency 8 kHzFrequency 12 kHzFrequency 18 kHz Power at 1 Power at 2 Power at 37 hours(Fixed power)12 hours 12 hours 13 hours8 hours8 hours9 hours7 hours7 hours7 hoursCOIL: 90mn / REMOTE CONTROLand HEADPHONES: 120mn.LiPo batteries (Lithium polymer) do not suer from the ‘memory eect’ so you can recharge them at any time without rst having to wait for them to fully discharge.The LED on the coil is on continually when charging is underway. When charging is complete, the LED reverts to ashing intermittently.(3 seconds ON, 3seconds OFF)MENU G.B.OPTION1 - BASIC 1 32POWER SUPPLY-batteriesLOW BATTERY LIGHTS BATTERY LIFE
The search coil is charged via the connection clamp supplied, which is connected to the coil according to the grooves in the coil cover. You will see that the clamp is shaped in such a way to prevent it being connected the wrong way round.Ensure that the clamp is the right way round before connecting it to the coil Connect the mini-B plugs to the remote control, headphones and to the charging clamp. The search coil, remote control and headphones are all powered by identical lithium polymer batteries. These miniature, high-capacity batteries can be recharged quickly. The dierent Dēus elements can be charged while switched on or o, but switching them o speeds up the process.You should use the power adaptor supplied, which enables all three elements to be charged simultaneously when used with the USB/3 mini-B cable, also supplied. Connect the USB plug to the power adaptorDISCSENSGNDFREQTONEVOLCOILCorrect Incorrect33POWER SUPPLY-batteries-MENU G.BOPTION1 - BASIC 1
The LiPo batteries are designed to bear hundreds of charges and to last several years in your detector, thus resulting in signicant savings in terms of purchase of batteries.After 300 to 400 charging cycles the battery still has 80% of its capacity, which then gradually begins to decrease over subsequent cycles. As an indication, the batteries should last for around 3 to 4 years when used on a weekly basis. Attention: long-term storage of discharged batteries may reduce their overall durability. If the detector has to be placed in storage, rst charge the batteries to half of their capacity (40 to 70%).Ideally you should then discharge/recharge them at least once a month.Do not store your device for long periods with discharged batteries!The three Dēus batteries are identical.The batteries for the wireless headphones and the remote control are easy to replace as they are connected to the circuit with a mini-connector and double-sided adhesive tape.The search coil battery is sealed for obvious reasons of safety and impermeability.It must be returned to our service department or an XP distributor for replacement.REPLACING BATTERIES34
The batteries are tted with internal protection systems which shield them from extreme overloads and discharges. They must not be dismantled or short-circuited, which is dangerous and could destroy the protection systems or cause the batteries to smoulder or ignite. Do not leave batteries charging unnecessarily and disconnect the power adaptor when the charge cycle is complete or after 120mn. If you notice any perforation, odour or other anomaly, please return the battery to the seller in a sealed plastic bag and don't try to charge again. Never dispose of lithium batteries with your household waste: return them to your XP seller or take them to a designated collection point. Do not place the batteries near heat sources and never throw them onto a reNever perforate the battery cover or try and weld/solder the battery. Do not short-circuit the battery terminals. Risk o explosion if battery is incorrectly replaced.Replacing the battery with another of the incorrect type can lead to an explosion risk. Only use LiPo batteries supplied by XP (ref : D088). PRECAUTIONS RELATING TO USE OF THE POWER ADAPTOR AND BATTERYBatteriesPower adaptorAcceptable ambient temperature during charging: 0° to 40°C MaximumRecommended storage temperature: 25°C35 The power adaptor is only designed for indoor use and should not be exposed to water or humidity. Always connect your power adaptor in an accessible, visible place to ensure that it can be unplugged quickly in the event of overheating or other problems. Use the special XP chargers in the recommended charging method to charge the battery, do not use other charger, that will cause the battery internal short-circuit and make it heat, smoke or burn. Do not charge the devices during a thunderstorm and unplug the power adaptor from the supply. Do not charge close to inammable parts.Xplorer shall not be held liable for any consequences arising from a failure to comply with the precautions for use.
Press Choose DISCRI with Press Choose 2 tones - 3 tones - 4 tones - Pitch using You can use the Multi-tones menu to sort targets into categories according to their conductivity, by assigning a specic audio tone to each category. The higher the target’s conductivity, the higher the pitch of the tone.Take some time to become familiar with the 2 tones, 3 tones, 4 tones modes using dierent targets, such as an iron nail and some aluminium foil, dierent coins, etc. The lowest pitched tone is assigned to iron. If you do not wish to hear it, select “Iron Volume” from the menu and reduce its volume to 0. If you are in 2 tones mode (low/medium tone) and you reduce the iron level (low-pitched tone) to 0, you then nd yourself in 1 tone mode (medium), which is why there is no 1 tone mode in this scrolling menu.Pitch mode is completely dierent from the others. It does not take into account the target’s conductivity: the strength of the signal generates an audio signal that varies both in amplitude and height (the audio frequency).This means that a more distant target will generate a low-pitched, weak sound whereas a closer target will generate a high-pitched, strong sound. Pitch mode gives signals particular dynamism and can be useful for locating targets. It also makes the detector seem more reactive. However, it does not fundamentally aect reactivity, just the audio.MULTI TONESThis section covers the advanced settings. You should ensure that you have studied all the basic parameters before moving on to this section.2 TONES - 3 TONES- 4 TONES PITCHMENUEXPERTMULTI TONES PITCH 3 TONES 4 TONES 2 TONESEXPERTMULTI TONES 2 TONES 3 TONES PITCH4 TONES36
Press Scroll with and select Press Choose 2 tones - 3 tones - 4 tones - Pitch with Once you have selected the number of tones (for example: 4 tones) Press You have the option of customising the sound partitioning of the discrimination range.A sound frequency (comparatively low- or high-pitched) is assigned to each part of the discrimination range. In this example, a low-pitched sound (202 Hz) is assigned to the signals from 0 to 10, a higher-pitched sound (518 Hz) is assigned to the part from 10 to 60, then 644 Hz is assigned to 60 to 87 and lastly a very high-pitched sound (757 Hz) is assigned to the part from 87 to 99. Press in order to move the cursor (black triangle) from one setting zone to another.Note that the cursor rst moves up and down to indicate the sound frequencies used, then from left to right to indicate each threshold. Adjust the sound frequencies and thresholds with Example: If a coin type, which your device registers as 58 on the conductivity index, signals as “medium low” (518 Hz) and you wish it to be signalled as “medium high” (644 Hz), you simply lower the threshold from 60 to 57 or less. Now, all coins with this conductivity value will register at 644 Hz. The black bar showing the index of the target is displayed in the top left of the screen (black bar) for help. This enables you to directly adjust the sound responses for targets you select as references. The threshold 1 separating the low-pitched tone (tone 1) from the medium tone (tone 2) is the same as the Discrimination value. These are the same settings. MENUEXPERTEXPERTMULTI TONES PITCH 2 TONES 4 TONESEXPERT3 TONES4 TONES2025186447571060 87TONE1 202 HZTHRESH 1T / 2T= 4 TONES2025186447571087THRESH. 2T/3T 57571087MULTI TONES, Thresholds and Tones 37
Press Scroll with and select PressDēus enables you to adjust the strength of the emitted electromagnetic eld according to three levels (from 1 to 3). It is adjusted using Press x2 to return to the main menu.By default the power is set to level 2, which oers a very dependable performance level that is largely sucient in most cases.The power only has a subtle eect on the device’s pure performance with regard to sensitivity. However, it increases your detector’s power consumption as well as alter its stability on dicult ground.On iron-infested, mineralised ground, there is no need to use a high power setting, level 1 will be sucient as in any case it is impossible to detect deeply in this kind of ground.It is therefore better to limit the saturation caused by iron and the ground by lowering the setting. In this way you will improve analysis and will ultimately nd as many, if not more, targets since you will be better able to hear them. Power is set to maximum for the 4 kHz frequency. You do not therefore have access to the Expert menu when you are on this frequency. MENUEXPERTSENSTX POWERMENU EXPERTDISC. FREQ. IRON VOL. SENS38
Press Scroll with and select Press Adjust the Silencer with Press x2 to return to the main menu.Iron is more easily discriminated than other metals because of its unique signature which is related to its ferromagnetic properties. However, large iron objects or certain unusual shapes are often more dicult, or even impossible, to discriminate. Press Scroll with and select Press Adjust the frequency with Press x2 to return to the main menu.You can shift your operational frequency slightly to avoid occasional interference, particularly that generated by another detector nearby. Starting from the central frequency, two other frequencies are available. Wherever possible, remain on the central frequency, which is more closely attuned to the emitter coil.During a rally or other group event, if you suer from any interference do not hesitate to shift the frequency. You can also simply change the basic frequency (4, 8, 12, 18kHz) to avoid interference from your team mate’s detector 4kHz frequency is xed and cannot be shifted.MENUEXPERTFREQMENU EXPERTSENS.IRON VOL. REACTIVITY. FREQ.FREQ SHIFT HZMENUEXPERTREACTIVITYSILENCEREXPERTMENU IRON VOL.AUDIO RESP.NOTCH. REACTIV.39
These partially discriminated iron objects often generate a few audible remnants of broken, inconsistent signals (crackling).Depending on your abilities and preferences, you may wish to remove this crackling using the Silencer.When you increase the value of the silencer you are applying a lter which eliminates the crackling caused by iron.Level 2 represents a good compromise, but if you have diculty distinguishing iron from non-iron, then use a higher level such as 2, 3 or 4. The Reactivity menu takes precedence over the silencer, so if you change the reactivity value this automatically imposes an appropriate silencer value. This is designed to avoid the silencer being set to a value that could reduce the eectiveness of the reactivity setting. MENUEXPERTNOTCHEXPERTMENU AUDIO RESP.DISC.SENS. NOTCHNOTCHN 146THRESH 128THRESH 24640 Press Scroll with and select Press and go to NOTCH screen. This advanced notch function enables you to widen the rejection window in the event that the undesirable target(s) have a wider conductivity range than the standard 6-point window.For example, if the undesirable target is generating a signature ranging from 28 to 46, you can use this option to lower the value of Threshold 1 to 28 and increase Threshold 2 to 46. Select threshold 1 or 2 with Adjust the values with Press X2 to return to the main menu.If several targets with dierent conductivity levels are bothering you, you can activate two other notches: N2 and N3Use to select N2 or N3, and adjust as for N1. To exit use You will note that the notched zones are greyed out in the conductivity bar on the main page.
INCORRECTCORRECT41Metal detecting is a fascinating leisure activity that can bring you a lot of satisfaction. However, it requires a minimum of learning in order to get the most enjoyment. Begin by familiarising yourself with your equipment and its operation on a suitable practice ground. To do this, we recommend that you take an assortment of dierent objects: coins, everyday items, metal rubbish, etc. Then nd a patch of ground relatively free from metal pollution and far away from any electromagnetic interference (high voltage power lines, electric fences, domestic appliances, etc.). For instance your garden would probably be one of the most unsuitable places to begin as there is too much domestic waste in the vicinity.To ensure that the site is suitable for practising, swing the coil over the ground as if detecting. If you hear a multitude of sounds then move to another place. Once you have found a suitable spot, arrange your objects on the ground, spacing them approximately two coil widths apart. Before placing an object, use the device to check that there is no metal already in the ground.Then, take some time to observe your device’s reactions when it passes over each target. You can then sort them according to the sound response type and try and understand what makes them similar or dierent. If you feel comfortable with this exercise, you can also try out some of the pre-congured settings.When detecting, it is important that you sweep the coil parallel to the ground, using wide movements, as close as possible to the surface (without actually touching it). Proximity to the ground will increase the likelihood of detecting a deep target and will enable the most discreet objects to be identied more easily. You are advised to avoid knocking the coil, as although it is designed to tolerate this kind of stress, careful treatment will prolong the life of the device and guarantee you better perception of targets.PRACTICAL INFORMATION
When you are detecting, you are free to choose the rate at which you move. For example, if you prefer to cover a zone at high speed while detecting, this will certainly give youa global ‘snapshot’ of the site. However, it is clear that this way of detecting will also leave large areas of ground unexplored between each sweep. On the other hand, if you insist on closely scrutinising every inch of the ground, you should ensure that each sweep slightly overlaps the previous one, in order to reduce to a minimum the area that your coil has not scanned.You should also bear in mind that you will further increase your chances of nding and identifying a target by sweeping more slowly. This particularly applies in metal-infested ground (when there are more targets to be sorted) or when you are searching for deeper targets. Once the detector has indicated the approximate presence of a target in Motion mode, if you are having diculty locating the target then sweep the place where you heard the sound. Slowly reduce the amplitude of your movements and make a mental note of the spot where the sound is loudest. If necessary, indicate it with a mark on the ground. Then move a quarter turn around the spot and begin sweeping again in the same way (at 90° to the rst sweep). You should then locate the precise zone containing your target at the intersection of the two sweeps, where the sound is loudest. Continue with crossed sweeps over the target. The loudest and highest pitched audio signal indicates the centre of the coil and therefore the position of the target. 42Target
Dēus is a precision device, designed to better address any detection constraints and be as robust as possible. Despite this, it is important to take care of it and exercise certain precautions in order to prolong its life:43Do not store your device for long periods with discharged batteries.Ideally you should discharge/recharge the batteries at least once a month, and if possible store them 40 to 70% charged.Do not expose your detector to extreme temperatures, particularly inside a car in full sun.Do not expose your detector to the sun without reason when it is not being used.When you switch on the detector ensure that the coil is not near any metal objects. Neither the remote control nor the headphones are waterproof. In wet weather be sure to protect them!Use the storage case that is supplied with the headphones and never carry them at the bottom of a bag without protection.Use the case that is supplied with the remote control to protect it in adverse conditions, and when the detector is stored away.Do not use solvents or alcohol to clean the detector. Soapy water is sucient.Depending on how you use your detector, it may be advisable to clean its elements regularly. A damp cloth can be used to clean the non-waterproof parts (headphones and remote control).After use, remove any dirt from the stem’s locking mechanisms.
CAUSES SOLUTIONSSelect the corresponding coil (pg 24/29).Check the coil’s serial number (pg 24/30).Recharge it. Contact your reseller or XP.Contact your reseller or XP. CAUSES SOLUTIONS You become aware of abnormal performance, instability, false signals, misplaced interference, for no apparent reasonRecharge it.Find a less infested place. Don’t practice in your garden!44Lower it.Lower the sensitivity or move to a dierent zone.Switch o and wait for the storm to passChange or shift the frequency (pg 11/12).Switch it o, then on again with the coil in the air and the stem fully deployed, away from any sources of metal.In manual mode set it to 90. Sensitivity is too high. You are in a zone with a lot of interference (high-voltage power lines, electric transformer, electric fence). There is a storm nearby and the electromagnetic discharges of lightning are interfering with the detector.You are close to other working metal detectors.You switched on the detector with the coil near a metal surface or near the stem’s aluminium tube (in the folded-up position).The ground balance is set too low.The battery is discharged. The ground is heavily infested with iron and other metals. The coil does not switch on, unlike the remote control and the headphonesYou have a dierent coil selected in the menu : OPTION / Coil from the remote control or in the menuCOIL from the headphones.The serial number of the coil that you had entered in the remote control was incorrect or was changed inadvertently.The coil battery is drained.The coil battery has reached the end of its lifespan.The coil is defective.
CAUSES SOLUTIONSCAUSES SOLUTIONSCAUSES SOLUTIONSCheck that you do not have a dierent coil selected in the COIL menu (pg 29/30).The headphones have not yet been paired with the coil.The coil’s serial number was changed inadvertently in the headphones and the headphones are no longer paired with the coil.Select the right coil (pg 29/30). Pair them (pg 30).Pair them (pg 30). The backphone is faulty.The earpiece is faulty, for example its keypad was poorly reconnected to the circuit after being dismounted, or the audio contacts are faulty or dirty.Change it, it is easy to replace (pg 31/48).Contact your reseller or XP.The ground balance is set too low. Dicult ground, highly mineralised and infested.Adjust the ground balance to 90 then try again.Change to a dierent zone.Ground control is too low. Increase the ground balance level untilfalse signals stop.Too many false signals when the coil is knocked The detectors beeps on potery and "hot rocks"CAUSES SOLUTIONS45There is no detection sound in the headphones despite them being switched on (and pressing the buttons generates an audible beep)There is no sound in the headphones when passing over a target and pressing the buttons generates no audible beep
RadioGeneral Features Settings46 Digital wireless 36 automatic channels 2.4 GHz / 0.56 mW 4 kHz, 8 kHz, 12 kHz, 18 kHz + shifts 99 levels 3 levels 6 levels 6 levels 6 levels 1, 2, 3, 4 tones, Pitch,+ Expert Tracking, Pumping, Manual, Wet beach Yes, with adjustable window width Motion/None Motion Yes, audio and visual Audio and visual 82 levels 90 levels Yes on wireless headphones 8192 pixels Yes, very low power consumption Yes, via USB / Internet connection Yes (can also serve as control unit) DD - Ca Yes Yes Yes Fully telescopic, S-shaped Lithium polymer, miniature x3 Yes, for all 3 elements 20 hours 20 hours 10 hours on average Yes - rapid and simultaneous charging of all 3 elements. Input 100-200V 50/60Hz, Output 5V 1A Optional, with 1 AA battery + 5 LED torch function Optional Coil: 90 mn, Headphones/Remote control: 120mn 979 g (880g without remote control) 435 g— 100 g— 80 g— 430 g with coil cover 58 cm 130 cm -5°C to 45°C 0°C to40°C 25°C Yes, but need an optional accessory to work (2010) 2 years parts and labour (mains power charger and batteries included) Registered and pendingLinkChannelsRadio frequencies and Radio powerDetection frequencySensitivityTransmitter PowerReactivitySound CurveIron levelMulti tonesGround balanceMulti-notchModePinpointDiscriminationIron discrimination rangeNon-iron discrimination rangeFactory programmesAudio volumeDisplay screenBacklightingSoftware updatesWireless headphonesCoilCoil coverBelt-mounted remote control caseHeadphones storage caseStemBatteriesBattery level indicatorRemote control battery lifeWireless headphones battery life Coil battery lifeMains power chargerField chargerCar cigarette lighter chargerCharging time Total weight with batteries Total weight of stem Weight of remote control with battery Weight of headphones with battery Weight of coil Length of folded stem Length of deployed stemOperating T° Max ambiant T° during charging Recommended storage T°Waterproof coilGuaranteePatentsSPECIFICATIONS
Emergency charger with AA battery (x1) with 5 LED torch function(Battery not provided) Car chargerOther optional coils 34 / 28 cm DD 47Security Strap for remote control Armband case MENU G.B.OPTION
Screwing kit for search coilRef: D038BTop part(with keyboard) Ref: D081RubberRef: D086Rubber Top Ref: D084Rubber Ref: D086Rubber BottomRef: D085Top part (with LCD and keypad)Ref: D092BackphoneRef: D090Board PCB Ref: D083(with LCD and battery)Bottom partRef: D082(with speaker and metal plate)LCD - Ref: D087Battery - Ref: D088Speaker - Ref: D089Full camlockRef: D041Coil coverRef: D02CoilRef: D01Lower stemRef: D03Middle part of aluminium stemRef: D04Magnetic holderfor remote control(with screws)Ref: D05Handle(with top part of alum.stem)Ref: D06Armrest (with screws)Ref: D07Locking parts for handleRef: D061Full electronic boxRef: D091PCB (with Battery)Ref: D093Bottom part Ref: D094Rubber Ref: D095Battery - Ref: D088FULL HEADPHONES - Ref: D09 FULL REMOTE CONTROL - Ref: D0848
Detecting is an activity which, like other leisure activities, requires a few general guidelines. These recommendations will enable everyone to enjoy their hobby to the full while respecting laws, places, the environment and other people.49Ensure you are informed of current legislation relating to discovery of treasure in order to abide by the law.Declare any fortuitous archaeological discoveries to the local authorities (town hall) of the discovery site within 48 hours.Before prospecting on a site, obtain permission from its owner(s) or guardian(s).Respect the natural environment in which you are prospecting and any other places to which you need access.Systematically back-ll any holes you make so as to leave a site exactly how you found it.Keep any rubbish you nd in order to dispose of it in a dustbin.Avoid detecting in areas where battles are known to have taken place during wartime. Exercise extreme caution with any suspect object resembling munitions, grenades, mines, shells, bombs, etc. and notify the relevent authorities (police, local authorities, etc.) of any such object you nd.Remember that you are an ambassador for metal detecting and it is important that you convey a positive image!
03 MENUDISC.SENSITIVITYFREQUENCYIRON LEVEL REACTIVITYAUDIO.RNOTCH 1GROUND BACKLIGHT * CONTRAST * MENU EXPERTDISC (threshold 1 TONE / 2 TONES)2 TONES3 TONES4 TONESPITCHTRESHOLD 2T/3 TONESTRESHOLD 3T/4 TONESFREQUENCY "TONE 1"FREQUENCY "TONE 2"FREQUENCY "TONE 3"FREQUENCY "TONE 4"TX POWERFREQUENCY SHIFTSILENCERNOTCH 2NOTCH 3MANUALBEACHTRACKING (Except Beach mode) SETTINGS0 to 99YES/NOYES/NOYES/NOYES/NO0 to 990 to 99200 to 791200 to 791200 to 791200 to 7910 to 991 to 34K/8K/12K/18K-1 to 10 to 50 to 5-1 to 40 to 500-00 to 99-9900-00 to 99-9900-00 to 99-990-30 (Beach)60-95(normal) YES/NOYES/NOOFF - 3s -10s - 60s -120s - ON0 to 9* Settings common to all programsBASIC 110NOYESNONO769520251864475790212K0022400-0000-0000-0090NONO60 S7GMPOWER6,8NOYESNO769520251864475790218K0322400-0000-0000-0090NONO60s7Programme 1 Programme 250Mineralised groundsSmalls targetsGeneral useFACTORY PROGRAMS
WET BEACH10NOYESNONO769520251864475785118K0033100-0000-0000-0027YES60s7ALL METAL0NOYESNONO76952025186447579028K0513400-0000-0000-0090NONO60s7BASIC 210NOYESNONO76952025186447578028K0013300-0000-0000-0090NONO60s7PITCH6,8NONONOYES769520251864475790212K0022400-0000-0000-0090NONO60s7G-MAXX8NOYESNONO76952025186447579028K0013400-0000-0000-0090NONO60s7DEUS FAST6,8NOYESNONO769520251864475790218K0332400-0000-0000-0090NONO60s7RELIC8NOYESNONO76952025186447579038K0303400-0000-0000-0090NONO60s7Programme 3 Programme 4 Programme 5 Programme 6 Programme 7 Programme 8 Programme 951Standard useGreater stabilityBeginnerGeneral useAudio signal varies both in amplitude and heightMineralisedand iron infested groundsSmalls targetsFaster than GMPOWERFor large masses and highly conductive coinsLarge, deep masses in relatively uncontaminated ground.More eectivelyfor wet beachareaAll targets Motion all métal mode
* Settings common to all programs03Programme 1 Programme 252 MENUDISC.SENSITIVITYFREQUENCYIRON LEVEL REACTIVITYAUDIO.RNOTCH 1GROUND BACKLIGHT * CONTRAST * MENU EXPERTDISC (Threshold 1 TONE / 2 TONES)2 TONES3 TONES4 TONESPITCHTRESHOLD 2T/3 TONESTRESHOLD 3T/4 TONESFREQUENCY "TONE 1"FREQUENCY "TONE 2"FREQUENCY "TONE 3"FREQUENCY "TONE 4"TX POWERFREQUENCY SHIFTSILENCERNOTCH 2NOTCH 3MANUALBEACHTRACKING (EXCEPT BEACH MODE) SETTINGS0 to 99YES/NOYES/NOYES/NOYES/NO0 to 990 to 99200 to 791200 to 791200 to 791200 to 7910 to 991 to 34K/8K/12K/18K-1 to 10 to 50 to 5-1 to 40 to 500-00 to 99-9900-00 to 99-9900-00 to 99-990-30 (Beach)60-95(normal) YES/NOYES/NOOFF - 3s -10s - 60s -120s - ON0 to 9
Programme 3 Programme 4 Programme 5 Programme 6 Programme 7 Programme 8 Programme 953
MENU EXPERTNOTCH SENS FREQDISC2 TONES202518 10TONE 1 202 HZOPTION CONFIGURATION COILPROGRAMSELECTOPTION PROGRAM CONFIGURATION COILSELECTPROGRAMRESTORESAVE EDIT NAMESELECTPROGRAMEDIT NAME RESTORE SAVESELECTPROGRAM SAUVE EDIT NAME RESTORESELECTOPTION PROGRAM CONFIGURATIONSELECTCOILBASIC -EDIT NAME676767676767EDIT SERIAL NUMBERCOIL EDIT NAME EDIT SERIAL NUMBERSELECTCOIL 2AEDIT NAMECOIL EDIT SERIAL NUMBER EDIT NAMESELECTCOIL2-COIL 34 CM (13") 1-COIL 22.5 CM (9")OPTIONCONFIGURATION UPDATE BACKLIGHTCONTRAST SPEAKER. OFFCONFIGURATION SPEAKER CONTRASTCLOCK SETTING BACKLIG. 3sCONFIGURATION BACK LIGHT CLOCK SETTINGUPDATE CONTRAS. 3CONFIGURATION CONTRAST UPDATE SPEAKER CLOCK S. UPDATESELECTCONFIGURATION CLOCK SETTING SPEAKERBACKLIGHTMULTI TONES PITCH 3 TONES 4 TONES 2 TONESEXPERTMENU G.B.OPTION1 - BASIC 1 OPTION MENUPROGRAM9-BASIC 2 2-GM POWER3-DEUS FAST 1-BASIC 1OPTION1 - BASIC 1 2 - GMPOWER 3 - DEUS FAST4 - PITCH 5 - G-MAXX 6 - RELIC7 - WET BEACH 8 - ALL METAL 9 - BASIC 254
G.B. TRACKING PUMPINGBEACH MANUALG.B. MANUAL BEACHETRACKING PUMPINGSTARTMANUALPUMPINGG.B. BEACH TRACKINGBEACHG.B. MANUAL PUMPINGLANCERG.B. PUMPING MANUAL BEACHNOTRACKINGIN PROGRESSG.B. MANUEL PLAGETRACKINGG.B. FAILMENU EXPERTDISC. FREQ. IRON VOL. SENSMENU EXPERTSENS. IRON VOL.REACTIVITY. FREQ.KHZMENU FREQ. REACTIVITYAUDIO RESP. IRON VO.MENU REACTIVITY. NOTCH.DISC. AUDIO R.EXPERTMENU IRON VOL. AUDIO RESP.NOTCH. REACTIV.EXPERTMENU AUDIO RESP.DISC.SENS. NOTCHTX POWER SILENCER4 TONES2025186447571060 87TONE 1 202 HZ3 TONES2025186441060TONE 1 202 HZFREQ. SHIFT HZMULTI TONES PITCH 2 TONES 4 TONESEXPERT3 TONESMULTI TONES 2 TONES 3 TONES PITCH4 TONESMULTI TONES 2 TONES 4 TONES PITCH 3 TONESEXPERTG.B.NOTCHN 146THRESH. 128THRESH. 24655
This product complies with standards for user safety with regard to electromagnetic waves. The strength of the radio signals used is considerably weaker and on a much smaller scale than those emitted by mobile telephones (2,000 to 4,000 times weaker), as well as being much less than those used by Wi-Fi systems. Moreover, when the complete system is used, the audio headphones only act as a passive radio receiver, and do not emit any signals.56Safety relating to electromagnetic radio wavesFCCFCC ID : XFJ225 FCC ID : XFJIHM FCC ID : XFJBKF XP METAL DETECTORThis device complies with part 15 and part 18 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.- Consult the dealer or an experienced radio/TV technician for help.Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Cet appareil ISM est conforme à la norme NMB-001 du Canada.This ISM device complies with Canadian ICES-001.IC:8392A-XP225 IC:8392A-XPIHMIC:8392A-XPBKFResponsible party: XPLORER SARL 31320 Castanet Tolosan
If this symbol is displayed on the product or its packaging, it means that the product must not be disposed of with your household waste. You must take it to a designated collection point for recycling electrical and electronic waste. This selective waste sorting and recycling helps to preserve natural resources and avoid any potential risks for human health and the environment that could result from inappropriate scrapping, due to the possible presence of dangerous substances in the electric and electronic equipment. For more information on places where you can take your electrical waste, please contact the shop where you purchased this product. Alternatively you can return it to your supplier, or directly to XP.The same is true for the lithium batteries which must be recycled appropriately, or returned to your supplier or directly to XP.WARNINGThe accessories delivered with these detectors may vary, and similarly the menus and certain features described in this manual may dier slightly from the product purchased.This detector is not suitable for applications involving the search for dangerous targets such as munitions, mines, etc. 57© 2009 Xplorer sarlThis document contains information that is protected by existing legislation on copyright, brands and royalties.Any reproduction, even partial, of this document, the logos or the XP and Dēus brands is prohibited without the agreement of: XPLORER SARL - 8 rue du Développement – F-31320 CASTANET-TOLOSAN FRANCE
ContactsWebsite : www.xpmetaldetectors.come-mail : info@xpmetaldetectors.comXPLORER sarl8 rue du développementF-31320 CASTANET TOLOSANFranceTel : 33 (0)5.61.73.63.29Fax : 33 (0)5.61.73.48.39XP and Dēus are trademarks of Xplorer sarl.Xplorer reserves the right to modify its detectors’ characteristics or specications without notice.58In addition to the statutory guarantee ensuing from Articles 1641 et seq. of the French Civil code, due in any case for aws and latent defects, Xplorer provides a contractual warrantywhich takes eect from the purchase date:Of 24 months on the entire product, including the lithium batteries and charger.In the event of a malfunction, the complete device must be returned to your reseller, accompanied by the purchase invoice and a note explaining the fault detected, with postage being payable by you. If a faulty device has been replaced by a new or reconditioned one, the guarantee will continue to apply as if the device was the one originally purchased.This guarantee for parts and labour does not cover:Breaks caused by falls or impacts Accidental damage Damage caused by abnormal use Degradation resulting from non-compliance with the conditions of use stipulated in the device’s instructions.Alteration of the electronic circuit by any unauthorised person.The guarantee does not cover the normal reduction in battery life due to batterie ageing.
QUICK STARTBy default you begin by using the 1 - BASIC 1 factory programme which is suitable for general use.If you wish to test one of the 9 other factory programmes, simply scroll through them with -DISCSENSGNDFREQTONEVOLCOILAfter charging your device. (pg 33)Validate or not the use of the loudspeaker -OUIYou’re now ready for detecting!Note Do not switch on Dēus when the coil is near a metal surface, inside a car, or when the stem has been folded away, as this may interfere with calibration and lead to abnormal performance. If this should occur, switch Dēus o and move away from any metal masses before switching it on again.Nevertheless, this does not represent any risk to the equipment or its electronics! If you wish to change the main detection settings:MENUPress arrow to scroll through the functionsPress Menu Set with - / + Press return arrowto return to the main menuSwitch on the headphones To switch o Dēus Hold down Power for two seconds on the remote control Press left and right buttons on the headphone. YESNOSwitch on the remote controlCoil far from metal surfaces
QUICK STARTBy default you begin by using the 1 - BASIC 1 factory programme which is suitable for general use.If you wish to test one of the 9 other factory programmes, simply scroll through them with -DISCSENSGNDFREQTONEVOLCOILAfter charging your device. (pg 33)Validate or not the use of the loudspeaker -OUIYou’re now ready for detecting!Note Do not switch on Dēus when the coil is near a metal surface, inside a car, or when the stem has been folded away, as this may interfere with calibration and lead to abnormal performance. If this should occur, switch Dēus o and move away from any metal masses before switching it on again.Nevertheless, this does not represent any risk to the equipment or its electronics! If you wish to change the main detection settings:MENUPress arrow to scroll through the functionsPress Menu Set with - / + Press return arrowto return to the main menuSwitch on the headphones To switch o Dēus Hold down Power for two seconds on the remote control Press left and right buttons on the headphone. YESNOSwitch on the remote controlCoil far from metal surfaces

Navigation menu