XYZprinting 3L10A 3D Printer User Manual NOBEL 1 0A EN V1

XYZprinting, Inc. 3D Printer NOBEL 1 0A EN V1

(Nobel 1.0A) UserMan

V1-1-Nobel 1.0A 3D PrinterProduct ManualENGLISHFEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/ TV technician for help.CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Safety and ComplianceRead the following safety instructions and contents of this manual before use, operation, maintenance, replacement or removal of any parts, components, or materials of the printer.For the latest information about the Nobel 1.0A 3D Printer and XYZprinting products, please visit XYZprinting website (http://www.xyzprinting.com) or contact your sales representative.The following has been written in order to cover all possible printing scenarios. For scenarios which occur outside the scenarios detailed in this manual, the user will be held accountable for their own safety.Resin Care•Wear proper protective equipment, avoid raw material contact and vapor inhalation.•Chemical-resistant gloves should be worn when you make contact with resin.•Avoid exposing resin to high temperatures, localized heat sources (i.e., drum or band heaters), oxidizing conditions, freezing conditions, direct sunlight, ultraviolet radiation, inert gas blanketing.•Never pour the waste resin back to the bottle or down the sink, as it may pollute the remaining resin or clog the drain. •You may pour resin waste into plastic bag and expose it to sunlight or UV light source to cure the resin. The cured resin can then be discarded. •Avoid dripping resin on anything other than the platform or the resin tank, or the printer may malfunction.CopyrightAll other trade names and trademarks are properties of their respective owners.Important Safety Information:•Do not let children operate this device without adult supervision. Moving parts may cause serious injury.•Electric shock hazard.•Do not place the printer on an unleveled or unstable surface. Printer may fall or tumble causing harm and/or injury. Also tank level detection may be inaccurate.•Do not place any object on top of the printer. Liquid and solid objects that fall into the printer may lead to printer damage or safety risks.•Please keep the printer, resin, or alcohol away from fire. •Do not disassemble or replace the printer cover with non-XYZprinting covers.•Insert and secure the power cord firmly for proper usage and to avoid potential electricity and fire dangers.•Do not attempt to service the printer beyond the instructions specified in this document. In the case of irrecoverable problem, contact XYZprinting service center or your sales representative.•Do not place the printer in humid or dusty environments such as bathrooms and high traffic areas.•Some components of the printer move during operation. Do not attempt to touch or change anything inside before powering off the printer.•Please keep the lid closed during printing to avoid injury.•This printer is a Class 1 Laser Product. A Class 3B laser module is used as a light source. Never disassemble the product.•For optimized printing quality, only use resin supplied by XYZprinting.•Make sure to set the power switch to the off position and remove the power cord before transporting the device.•Only use the grounded power adapter and power cord supplied with the printer to prevent possible electrical shocking.•Please place and use the printer in a well ventilated area. The process of printing will produce a small amount of non-toxic odor. Having a well ventilated area will ensure a more comfortable environment.V1-2-Resin Tank Care•Due to the nature of the print technology and material, the resin tank may develop cloudy regions overtime where the laser cures the resin frequently and may lead to print fails. Moving the print location around the platform can help prolong the life of the tank.•Change to a new tank when over 2/3 of the surface gets cloudy.•Use a separate resin tank when using resin of different colors. Mixing resin of different color may affect printing quality.Cloudy
V1-3-⑦Shake the resin bottle for around 10 seconds to ensure even color.⑧Assemble the nozzle cap and the tube (placed in the rinse basket when shipped).⑨Replace the bottle cap with the assembled nozzle cap.Unpacking & SetupAfter removing all external packing materials and tapes…①Take off the lid and remove the accessory tray over the platform.③Connect power adapter, power cord to the printer. Switch on the printer. (Please do not use the power adapter for Nobel 1.0 on this model.)②Lay down the printer, and release the printing module locker by pushing it to the right. Follow the procedures to remove the protecting foam under the platform.④Raise the platform:On the printer screen, select “UTILITIES” and press ► to find “MOVE PLATFORM”>”TO TOP”. And press “YES” to raise the platform.⑤When the platform is moved to the top, remove the protecting foam.⑥Unpack the resin tank and insert it into the tank slot. Push all the way until reaching the end. ⑩Install filling tubes. Push the tubes all the way down.First attach the black tube to thick nozzle, and then connect the transparent tube to thin nozzle. Put on the lid, and it’s ready for printing.(Bottom of the printer)
Product Overview & AccessoriesUse the Display and Control PanelV1-4-To control and maintain the printer, you will need to operate certain functions with buttons on the control panel. Here is the map of the buttons:Move upNextpageMove downBack/CancelHome menuConfirm selection and settings/Exitnobel 1.0A►UTILITIES SETTINGS INFOPlatformQuick Start GuideFilling TubesCartridge SlotTank SlotOperation PanelLidResin TankRinse BasketGlovesScraperUSB Flash DriveInner TubeNozzle capPower CablePower Adapter Starter ResinUSB WirePower JackUSB Wire PortUSB Drive Port(Back View)PowerSwitchWarranty Card
LCM MenusUTILITIESINSTALL RESINV1-5-“Utilities” menu provides the control of the printer. You can instruct to fill the resin tank manually, and calibrate the printer when necessary.You can activate resin-filling function manually. Before doing so, make sure the resin bottle, resin tank and the lid are installed correctly. (See “Unpack & Setup” for details).“Horizon Calibration” ensures the platform is parallel with the resin tank for more stable printing performance. Always perform “Horizon Calibration” after changing to a new tank or a tank different the one used for last print.Select “Yes” and press [OK] to begin:• “Auto Fill” function is enabled by default. You may skip loading resin manually when auto-fill is enabled. • Shaking the resin bottle well before use ensures an even color.• The printer detects the tank level after "Install Resin" is activated. Resin will be filled only when the tank level is low. HORIZON CALIBINSTALL RESINBOTTLE BY NOW NO►YESMAKE SURE PIPESARE INSTALLEDCORRECTLY[OK] FOR NEXTRESIN TANK ISFILLING UP NOWPLEASE WAIT…[OK] TO CANCELSelect “Yes” and press [OK] to begin:NoteTo ensure the accurracy of calibration, please empty the resin tank before calibrating.Note①START HORIZONCALIBRATION NOW? NO►YES②REMOVE OBJECT FROM PLATFORM[OK] TO CONTINUE③LOOSEN 4 SMALLSCREWS ABOVETHE PLATFORM[OK] TO CONTINUETighten the screws with fingers. First tighten the front screws. Fasten screw F1 then F2. And tighten the screws at the back. Fasten screw B1 then B2.Finally tighten the screws with a coin or other tools (sequence from F1, B1, F2 to B2) and press [OK] to complete calibration.When you see the message above, press the platform with both hands 3 times. Make sure you see the right side of the tank sinks into the tank slot slightly.Wait for 5 seconds so the silicon finish on the tank can reshape. Check the tank frame has reposi-tioned (there's no gap between the frame holders).⑤TIGHTEN ALL 4SCREWS ABOVETHE PLATFORM[OK] TO FINISH④Wait until the platform descends to the bottom.PROCESSINGPLEASE WAIT...F1F2 B1B2F1F2B1B2
MOVE PLATFORMActivate the function when you need to move the platform manually. Simple select move the platform “to top” or “to bottom” to proceed: MOVE PLATFORM TO TOP►TO BOTTOMMOVE PLATFORMTO BOTTOM NOW? NO►YESTASK COMPLETE[OK] TO FINISHSETTINGSBUZZERV1-6-The Settings menu alows you to adjust printer settings.When the buzzer is turned on, the printer will output an audible signal when a button is pressed, print job is finished, or issue is detected. When “Auto Fill” is enabled, the printer will fill the resin tank before printing and when low tank level is detected. With the auto-fill function, you no longer need to manually refill the resin during printing. This is especially useful when printing large objects.Buzzer is turned on by default. To switch off the buzzer:Select “OFF” and press [OK] to change the setting.AUTO-FILLBUZZER [ON]►OFF ON“Auto Fill” is enabled by default. To disable the function:Select “OFF” and press [OK] to change the setting.• Be sure to place the printer on a leveled surface, or tank level detection may be inaccurate.• Auto-fill will be switched off when the timeout expires. Timeout may be caused by an empty resin bottle or the tank level sensor soaked by resin. Please replace the resin bottle or clean up the level sensor before enabling the function.NoteAUTO FILL [ON]►OFF ONLANGUAGEYou may switch the display language on the printer.The default lanague is English. To switch to other language:LANGUAGE [EN] ENGLISH►ニホンゴ FRANCAISSelect a language and press [OK] to change the setting.
ENERGY SAVELED backlight of the LCM enhances the readibility of the content of the display. To save energy consumed, the backlight will go off after the printer idles for 3 minutes (shown as 03M on the display) by default.To set a longer time interval:Select an option, and press [OK] to change the setting. Backlight will never go off.Backlight will go off after the printer idles 3 minutes.Backlight will go off after the printer idles 6 minutes.INFOV1-7-Under “Info” menu, you can check the statistics and firmware version of the printer, status of resin bottle installed, and information on XYZprinting.SYSTEM VERSIONFirmware version is shown here. To ensure optimal printing performance, it is advised to keep the firmware up to date. To check for firmware updates, please go to XYZware_Nobel.Select a language and press [OK] to change the setting.The content may look like this:RESIN STATUS“Resin Status” provides the information on resin level (see REMAINING), and the capacity, color and material of the resin. Press▼to read the second page.SENSOR STATUSWhen you encounter exceptional status during the operation of the printer, you may check the status of each sensor here. The information is especially helpful for troubleshooting.SENSOR STATUSC:0 Z-T:1 Z-B:0 T:1 L:0[OK] TO RETURNHELPThe URL to XYZprinting website can be found here. You may go to the website for the latest information, product documents, tutorial video and more. HELPXYZPRINTING.COM[OK] TO RETURNHow to read the satus:C:1 – Lid (Top cover) covered; C:0 – Lid not coveredZ-T:1 – Platform at top; Z-T:0 – Platform away from topZ-B:1 –Platform at bottom; Z-B:0 - Platform away from bottomT:1- Tank motor in action (Right side of the tank sinks slightly) T:0 - Tank motor idles (Tank is leveled)L:1 – Tank level low; L:0 – Tank full or tank not installedRESTORE DEFAULTAll settings can be reset to factory default with a few clicks.To reset all settings at once:RESTORE DEFAULTARE YOU SURE? NO►YESSimply select “YES” and press [OK] to reset.ENERGY SAVE [OFF]►OFF 3 mins 6 minsSYSTEM VERSIONENGINE:0.0.0.12LCM :0.0.7[OK] TO RETURNRESIN STATUSCAPACITY 500GREMAINING 10%[OK] TO NEXTRESIN STATUSCOLOR :GREY[OK] TO RETURN
V1-8-• Please slice the 3D model with XYZware_Nobel and save it in .3w/.3wn format. Files in other format or not sliced with XYZware_Nobel will not be shown.• For correct file name display, please name the file with English and Japanese (Katakana preferred) alphabets and numbers.* Sample files are provided in the bundled USB drive. To print the sample, please slice the file with XYZware_Nobel before printing.NotePRINT FROM USB"Layer Height" indicates the resolution of a print. Using thinner layers will make higher quality prints but will also take longer to print. Printing setup varies based on the color and material of the resin. Please set the option based on the resin cartridge installed on the printer before printing. It is advise to include color setting in filename for instant distinction in the future.The setting of Quality has impact on the smooth-ness of the surface of the printout. When printing with "Good" quality, the surface with less features will be more smooth. With the setting, it will take slightly longer for printing.Check "Brim" for the 3D objects that has less contact with the platform to increase adhesion. Options under Export :④①②③①② ③④PC-link Printing via XYZware_NobelBefore printing from PC, please first install XYZware_Nobel on your device. Connect your PC to the printer before installing the software, or the installation may be incomplete."XYZware_Nobel" Installer can be found in the bundled USB drive or at XYZprint-ing website: http://support.xyzprinting.com/global_en/Support/download (log in is required)Minimum system requirements for XYZware_Nobel:System RAM: 4GB and aboveGraphics RAM: 1GB and above (OpenGL 2.1+ compatible)Hard disk space: 300MB and moreOperating system requirements : Windows 7/8+ (32bits and 64 bits) Mac OSX 10.8+ A. B. Import objects in .stl/.3wn format: Open file browser and select the .stl or .3wn files to print. ".3wn" format is sliced by XYZware_Nobel based on the printer type selected. For the file set to slice for printer type other than "Nobel 1.0A", it will not be printed on this printer.Export to .3wn format: After selecting a desire printout setting, click on "Export" to save the model to a sliced .3wn file. Once the file is sliced, you may skip repeating settings in the future.(Overview of XYZware_Nobel)Functions:Insert USB flash drive to the USB drive port at the back of the printer.press ▼ to browse the menu, and press [OK] to select a file to proceed: XYZ_KEY►Mini_nobel my_nobel XYZ_KEY2START PRINTING? XYZ_KEY NO►YESAGHIJKLMNOB C D E FGood
V1-9-Operation Flow① Click "Import" to import a .stl/.3wn file to the virtual platform.② Adjust the placement, angle and size of the object with "Move", "Rotate" and "Scale" buttons on the left as desired.Please note that .3wn file is unadjustable.③ Click "print" and setup printing preference based on the features of the prints, and click "Print" to slice and send the file for printing. C. D. E.F.G.H.I.J.K.L.M.N.O.Save as .stl file: Save all objects on the platform to a single stl file. Any adjustment to the size or placement of the objects will apply to the stl file. Setup printing preference and send the objects for printing: Once your device is connected to the printer, click "Print" to open printout setting window (options are the same as "Export" window). Set your printing preference based on the features of the objects and hit "Print" to proceed. Setup interface language, display unit, light strength tuning and etc.Tips for Printout Scaling:If you find the dimension of the printout doesn't match the 3D model, you may adjust the scale of the X/Y axis.The setting will be stored in the software and applied to every print job afterwards.Info/Software & firmware update: Apply printer firmware and XYZware_Nobel updates when prompt by the software for stable printing perfor-mance.Zoom in/out: Zoom in or out the platform to view the details of objects.Switch views: Switch views with a click to view objects from different angles.Support structure: support structure is required under overhangs. It prevents the falling for gravity and the deforming duo to the stickiness during printing, and increases adhesion of the model to the platform.Support auto generation: XYZware_Nobel is able to analyze the features of the model and add support structure to where necessary. Simply select a desired density ① and size ②, choose to "Lift" ③ the print and/or print without internal support ④, and press "Generate" to preview the support structure.① Density : Large overhangs will require more support structure. However, more support structure will take longer for printing.② Size : Thicker contact point will lead to higher strength but will take longer for printing.③ Lift : Lift the objects over the platform will ease the removal after printing. However, the support structure under the prints will take longer for printing.④ Inner Support : For objects with inner overhanging structure, XYZware_Nobel will add support to the parts. However the support at inside may not be removed easily, you may consider printing without inner support. Manual editing: you may add or delete support structure based on the features of the print manually. To add support, simply select a proper size of the contact point and then click on the model at the overhangs. To delete support, just click on the support mark (the blue dot). After setting up support marks, click "Generate" to continue.You may generate support automatically with XYZware_Nobel, and then add/delete the support structure based on your printing experience. Use both functions help to ensure the success of printing, and may decrease resin consumption and shorten printing time.Move the object: move the object along the x, y, or z axis. You may also press and hold ALT key and drag the mouse to move the object horizontally.Rotate the object: adjust the angle of the object around the x, y, or z axis. Flipping the object around to adjust the face on the platform may help to enhance printing performance. Increasing the contact area between the object and the platform may help to enhance printing quality and strength.Resize the object: Scale the object as you desire. The adjustment to the object on the platform will not affect the size of your original file.View info of the object: check the dimension and location of the object, so you can tell the size of the object easily.Remove the object from the platform: select an object and click the option to delete it from the platform. Or you may press Delete key to remove the object. View printer statusTip①②④③(mm)Support mark④
① Remove any residue or dust from the platform and tank with the scraper, filter or other tools.② Mop the fingerprint or resin under the tank or on the glass with with lint-free cloth dampened with alcohol.③ Brush the level sensor with alcohol if it gets stuck.Level sensor should return to the original position after a soft push. When the tank is full or the resin gets sticky, the sensor's movement may be hindered greatly. It may take 1 minute for sensor to return to normal speed. If stuck, remove the remaining resin from tank before cleaning. If resin in tank is cured, please replace the tank.Check Before Every PrintCheck the following items before printing to ensure printing quality and the operation of the printer. V1-10-
V1-11-Printed Object Removal and Cleaning Resin Tank CleanupWhen removing prints from the printer, follow the procedure to post-process the object and maintain your printer.Always remove the platform before removing the resin tank to avoid dripping leftover material on printer surface. Note① Remove the platformWear gloves before removing the prints. Turn the platform locker counterclockwise until it stops. And pull the platform to remove it.To remove any residue stuck to the bottom of the resin tank, clean the tank level sensor covered resin, or to clean the tank thoroughly, follow the procedure for cleaning:① Pour uncured resin in the tank into a waste bin. For remaining resin, scrape the surface of the tank gently while pouring the liquid out.Scrap off the print gently to avoid damaging the surface of the platform. Note② Use the scraper to remove printRemove any residue in the resin tank. Operate gently to avoid scratching the surface of the resin tank. Reinstall the resin tank after cleaning.Scrap off any residue and remove excess resin from the surface of the platform. Turn the platform locker clockwise until it stops when reinstall-ing it to the printer. Uncured resin in the tank can be left for future printing. To prevent dust from accumu-lating on the resin, always cover the lid over the printer after removing any residue from the tank or the platform. Place the printer away from direct sunlight or UV lighting, even if the lid is covered, or resin in tank may cure and solidify. ④ Cleanup and reinstallNote③ Rinse part in Alcohol (≧75% Alcohol)Pour alcohol into the rinse basket, shake the print for 10 minutes, then rub it with your fingers though-roughly.② Scrape off the residue stuck on the tank gently. Avoid damaging the silicon finish.⑤ You can either wait until the alcohol in the tank evaporates completely or wipe away the alcohol with a lint-free cloth.If resin in tank is cured, please replace the tank.④ Spray alcohol on the tank and the silicon finish, and wait for around 1 minute. Gently scrape residue and pour remaining alcohol left in the tank into the waste bin. Repeat these steps until all residue has been removed.③ Clean the tank level sensor if it gets stuck. Loosen the 2 screws (A&B) above the sensor before dismounting. Then brush any resin in sensor parts and on the floater with alcohol. To mount the sensor on the tank, tighten the screws over the sensor lightly. Avoid over-tightening the screws as the wall may crack.Regular maintenance on the tank level sensor is essential to maximum the service life of the resin tank and ensure the smoothness of the operation.AB
SpecificationTroubleshootingNobel 1.0A 3D PrinterWhen an error occurs, please refer to the service code on the printer and/or in the software, and check the suggestion below for troubleshooting.If any error persists, please contact customer service center for support.Print TechnologyUV Light SourceMaximum Printing AreaX/Y Axis ResolutionZ Axis ResolutionFile FormatOperating ConditionsStereolithography (SL)UV Laser λ 405nm (100mW)128 x 128 x 200mm5”x 5”x 7.8”0.15mm0.025/0.05/0.1 mm.stl & .3wn (sliced with XYZware_Nobel)Temperature: 18-35℃/64.4-95℉Humidity: 40-80% RH (no condensation)USB Wire & USB drive100-240V 50/60Hz 60W 280 x 337 x 590 mm11”x 13.2”x 23.2”9.6 KGPhotopolymer ResinWindows 7/8 and aboveMac OSX 10.8 and aboveConnectivityAC InputPrinter DimensionNet WeightPrint Material OS Support● Error Code 1000: Vibration generator movement abnormalities or tank sensormalfunctioned Suggestion: Contact customer service center directly.V1-12-Post-Process Your PrintsRemove Support StructureUse pliers or other tools to remove the support structure from the cleaned prints to ensure perfect finish.Empty Uncured Resin Inside the Prints Hollow prints with uncured resin inside may break as time passes. To ensure the durability of hollow prints, leave a weep hole at the bottom of your 3D design, so you can empty the uncured resin easily.
● Error Code 1001: Z axis motor upward movement abnormalities or Z axis top sensor malfunctioned Suggestion: Select "INFO">"SENSOR STATUS" on the printer, touch Z axis top sensor, and see if the status of "Z-T" switches from 0 to 1. If the value doesn't switch accordingly, then the sensor is malfunctioning. Then select "UTILITIES">"MOVE PLATFORM">"TO TOP" to raise the . If the platform doesn't rise accordingly, then the motor is malfunctioning. Contact the service center after you have checked the status of the printer.● Error Code 1002: Z axis motor downward movement abnormalities or Z axis bottom sensor malfunctioned Suggestion: Select "INFO">"SENSOR STATUS" on the printer, touch Z axis bottom sensor, and see if the status of "Z-B" switches from 0 to 1. If the value doesn't switch accordingly, then the sensor is malfunctioning. Then select "UTILITIES">"MOVE PLATFORM">"TO BOTTOM" to descend the platform. If the platform doesn't descend accordingly, then the motor is malfunctioning. Contact the service center after you have checked the status of the printer.● Error Code 1003: NFC tag reader malfunctioned Suggestion: Contact customer service center directly.● Error Code 1004, 1006, 1007, 1008: Engine board malfunctioned Suggestion: Contact customer service center directly.● Error Code 1005: Y axis movement problem Suggestion: Remove the resin tank, release 3 latches by the glass and remove the glass. If you find any object falls inside the printing chamber and blocks the movement of the printing module, please remove it. If you find the belt is broken, please contact the service center. ● Error Code 2000: Resin filling timeout Suggestion: If the resin bottle is not empty, and the NFC tag matches the cartridge, first check if the nozzle cap is securely closed. Then check if the tank level sensor is functioning. Select "INFO">"SENSOR STATUS", and touch the tank level sensor. If the value doesn't switch from 1 to 0 after "L", the sensor is not working. Then tap the tank level sensor to see if it moves smoothly. If the sensor gets stuck, clean the sensor by following the cleanup procedure on Page 11 in the Product Manual. Also check the status of the filling pump. Disconnect the transparent filling tube, and select "UTILITIES">"INSTALL RESIN". If you don't feel air releasing from the tube, then the pump is malfunctioning. Contact the service center after you have checked the status of the printer.● Error Code 1020: Printer not found Suggestion: Make sure printer is powered on, and connected to PC correctly. If the error persists, please try to restart your PC or refer to FAQ on XYZprinting website.● Error Code 1021: XYZware_Nobel slicer not found Suggestion: Reinstall XYZware_Nobel.● Error Code 1022: Transmission failed Suggestion: Make sure the USB wire is securely connected to the printer. Do not remove the wire before data transmission is completed.● Error Code 1023: Insufficient memory to load file(s) Suggestion: Increase system memory to 4G RAM and 1G graphics RAM or above. Leave some prints for next task if you are printing several models.● Error Code 1024: XYZware_Nobel runtime error Suggestion: Restart XYZware_Nobel.V1-13-
V1-14-● Error Code 2001: Resin bottle not found Suggestion: Make sure resin bottle is placed correctly and NFC tag is in place under the bottle. If the NFC label is missing, please contact customer service center.● Error Code 2004: Lid not covered during printing Suggestion: Place the lid on the printer before printing. If the lid is placed correctly, please remove the lid, select "INFO">"SENSOR STATUS", tap the lid sensor and see if the status of "C" switches from 0 to 1. If the value doesn't switch accordingly, then the sensor is malfunctioning. Contact the service center after you have checked the status of the printer.● Error Code 2002: UV laser module not calibrated Suggestion: Contact customer service center directly.● Error Code 2003: Resin bottle empty Suggestion: Resin bottle is empty is based on the the reading from the NFC tag. Select "INFO">"RESIN STATUS" to check resin level. When "REMAINING" is shown as "0%", then the resin bottle should be empty. Please install another XYZprinting resin bottle before printing.● Error Code 2005: Unrecognized resin tag Suggestion: Check the record of the resin bottle by selecting "INFO">"RESIN STATUS". If the display shows "UNIDENTIFIED TAG", please change to XYZprinting resin bottle.● Error Code 2006: Unsupported file format Suggestion: "Print from USB" supports only .3w/.3wn format. Please select files in the supported format. ● Error Code 2007: File too large Suggestion: Please select a .3w/.3wn file, size no more than 200MB.● Error Code 2020: Printer is busy Suggestion: Wait until the printer finishes current task. If the error persists when the printer is idle, please try to restart the printer.

Navigation menu