XceedID 1050MINI Physical Access Control Reader User Manual INSTALLATION SHEET XF1050 1

Download:
Mirror Download [FCC.gov]
Document ID	545162
Application ID	bTqCxkCmFeZUKYqESQyMeA==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.31kB (53832 bits)
Date Submitted	2005-05-24 00:00:00
Date Available	2005-05-24 00:00:00
Creation Date	2005-05-20 10:18:39
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2005-05-20 10:18:39
Document Title	Microsoft Word - INSTALLATION SHEET XF1050_1.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Mike Conlin

INSTALLATION SHEET
XF1050
PARTS LIST:
•
•
•
•
•
•
1 - Installation Sheet
1 - Mounting Plate
1 - Potted Reader Assembly
1 - Cover
2 - Mounting Screws
1 - Assembly Screw
Removal:
1. Remove unit from box.
Mounting the Reader:
1. Determine an appropriate mounting position on the door frame or wall, be sure to
account for any applicable ADA height requirements.
2. Drill a minimum of two mounting holes a minimum of 1.35” apart on the mounting surface
of the door frame or wall. Drill one 3/4” diameter cable hole for the pigtail wire
connection. Wire the unit according to the color code chart below. Screw mounting plate
to wall. (ILLUSTRATION)
3. Following cable connection (see the cable connection diagram below), re-install the
plastic cover to the reader base. The base male connectors should align with the cover
connector holes and the bottom slot should easily slide over and snap into place over
the plastic dimple of the base. After ensuring connection, install the security screw on
the bottom of the reader.
Cable Connections:
1. XceedID XF1050 readers are supplied with a 8 conductor cable pigtail. Connect this
pigtail with the host/panel being careful to match the color of each wire with the chart
shown below.
(ILLUSTRATION)
Blue =
Green =
White =
Orange =
Brown =
Red =
Black =
Drain =
Beeper
Data 0
Data 1
Green LED
Red LED
Power +DC (6-16 VDC)
Ground
Shield Ground
Note: If Hold function is desired, it can be assigned to any of the Brown, Orange or
Blue wires in lieu of the function above.
2. Use a DC power source between 5 volts and 16 volts.
XceedID : Document No: 0213-01; Issue No. 1; 5/20/2005
3. Be sure the reader is properly grounded by attaching the ground wire to an earth ground
connection at the power supply or panel end of the cable.
Testing the Reader:
1. Power up the reader. The LED will light followed by a beeper tone. This indicates that
the reader is ready.
2. Present a proper card or token programmed to operate the reader and a green LED
flash will indicate successful operation. Note that a red flash could simply indicate an
incorrect match or mis-programmed card/token rather than a faulty reader installation.
Additional Notes:
• The voltage specification for these products is 5 volts to 16 volts.
• Typical cable gauge ranges from 18 to 22 gauge. Check with your cable supplier to
determine the best choice for your application and installation distance.
Specifications:
•
•
•
•
•
•
•
Power Supply: DC
Voltage Range: 5 – 16VDC
Temperature Range: -25F to 125F
Card Read Distance: Up to 4.0” – Distance can vary widely depending on installation
conditions and credential type.
Cable Distance to Panel in Wiegand mode:
o 500 ft. maximum @ 22 awg.
Information Output: Wiegand = up to 64 bits
Regulatory Approvals and Standards
UL
ISO15693
ISO14443A
Europe: CE Listed.
Federal Communications Statement:
The FCC requires the following statements for your information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This reader utilizes radio frequency energy and has been tested and complies with the limits of
FCC testing. Changes, modifications or disregard of proper installation instructions not expressly
approved by XceedID Corporation is strictly prohibited by the FCC and could void the user’s
authority to operate the equipment.
For Canadian Users:
This unit has been tested and meets all applicable Industry of Canada technical specifications.
• This device may not cause radio frequency interference.
• This device must accept radio frequency interference.
In the unlikely event interference occurs, please contact the manufacturer.
XceedID : Document No: 0213-01; Issue No. 1; 5/20/2005

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:77f4128a-8edd-41ed-9c75-59328bc94690
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2005:05:20 10:18:39-06:00
Create Date                     : 2005:05:20 10:18:39-06:00
Document ID                     : uuid:28c346d1-6d14-47c5-a085-14ce60efd5f1
Format                          : application/pdf
Title                           : Microsoft Word - INSTALLATION SHEET XF1050_1.doc
Creator                         : Mike Conlin
Author                          : Mike Conlin

EXIF Metadata provided by EXIF.tools