Xeline LTd SU-200BX PLC(PowerLine Communication) Modem User Manual SU 200BX Manual eng V08
Xeline Co., LTd. PLC(PowerLine Communication) Modem SU 200BX Manual eng V08
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 560215 |
| Application ID | mXeYaOLVUqg0ifDmziRuXw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 72.51kB (906349 bits) |
| Date Submitted | 2005-07-08 00:00:00 |
| Date Available | 2005-07-08 00:00:00 |
| Creation Date | 2005-06-17 13:55:20 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2005-06-17 13:55:20 |
| Document Title | Microsoft Word - SU-200BX_Manual_eng_V08.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | simyunsong |
SU-200BX Installation Manual (For Technicians Only) PLC Slave Unit Plug into the future Powerline Communication by Xeline Xeline Co., Ltd. SU-200BX Installation Manual ATTENTION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Change or modification not expressly approved by the party responsible for Compliance could void the user’s authority to operate the equipment. This equipment conforms with the following CE standard(s): EN60950-1 This document is subject to change without prior notice. SU-200BX Installation Manual Table of Contents 1. Introduction ······························································································· 5 2. Before Installing the SU-200BX ········································································· 6 2.1 Package Contents ························································································································ 6 2.2 Prerequisites································································································································· 6 2.3 Safety Precautions······················································································································· 7 3. Getting to Know the SU-200BX ········································································· 8 3.1 Front View ···································································································································· 8 3.2 Rear View······································································································································ 8 3.3 Product Specifications················································································································· 9 3.4 Minimal Requirements for the Subscriber’s PC ········································································ 9 4. Installing the SU-200BX················································································· 10 4.1 Connecting the SU-200BX to the Subscriber’s PC ·································································· 10 4.2 Configuring the SU-200BX········································································································· 11 4.3 Configuring the Subscriber’s PC······························································································· 12 4.4 Final Check (Ping Test)·············································································································· 15 4.4 Resetting to Factory Default Mode·························································································· 17 5. Trouble Shooting························································································· 18 6. Appendix ·································································································· 19 This document is subject to change without prior notice. SU-200BX Installation Manual Figure Index Figure 1 XPAS-200B PLC Internet Access System Configuration................................... 5 Figure 2 SU-200BX Package Contents......................................................................... 6 Figure 3 SU-200BX Front View ................................................................................... 8 Figure 4 SU-200BX Rear View .................................................................................... 8 Figure 5 Connecting the RJ-45 cable and SU-200BX ................................................. 10 Figure 6 Connecting the Power Cable...................................................................... 10 Figure 7 Connecting the SU-200BX to the Subscriber’s PC ........................................ 11 Figure 8 Network and Dial-up Connections .............................................................. 12 Figure 9 Local Area Connection Properties .............................................................. 12 Figure 10 Internet Protocol (TCP/IP)....................................................................... 13 Figure 11 Fixed IP Address Setting........................................................................... 13 Figure 12 Show Icon in TaskBar ............................................................................... 14 Figure 13 Network Configuration Complete............................................................. 14 Figure 14 Command Prompt Window....................................................................... 15 Figure 15 Checking the Configured IP Address ......................................................... 15 Figure 16 Pinging the Default Gateway IP................................................................ 16 Figure 17 Checking the Ping Results ........................................................................ 17 This document is subject to change without prior notice. SU-200BX Installation Manual 1. Introduction Powerline Communication (PLC) technology uses the existing powerline infrastructure to transfer high-speed data, eliminating the need for expensive and complicated cable installation. Because the home or office is already a ‘wired network’ through powerlines, Xeline’s PLC system offers a cost-effective and easy-to-install Internet access solution from any electrical outlet. Xeline’s SU-200BX is the PLC Slave Unit of the 24Mbps XPAS-200A PLC Internet Access System, and is designed to enable the end-user to instantly access the Internet or home network from any electrical outlet in the home or office. One SU-200BX is needed for each PC or device that you wish to connect to the network. Due to the smooth and high quality of data communication, the SU-200BX can also be used with various application equipment to provide value-added services such as VoPL (Voice over Powerlines) and video conferencing. The XPAS-200B system supports both Master/Slave or Ad-hoc topology and is based on Xeline's proprietary Cell-structured MAC (CMAC), which offers virtually unlimited number of nodes per physical network. Remote configuration and firmware upgrade are also supported for efficient setup and maintenance of the PLC units in mass-usage environments. Figure 1 XPAS-200B PLC Internet Access System Configuration This document is subject to change without prior notice. SU-200BX Installation Manual 2. Before Installing the SU-200BX 2.1 Package Contents Before installing, first verify that you have all of the following items. ○ SU-200BX PLC Slave Unit ○ 1 AC power cable ○ 1 Installation Manual ○ 1 RJ-45 cable (CAT 5) * Core manufactured by: E-Tech Electronics Co., Ltd. Model No. cu1330b Figure 2 SU-200BX Package Contents If there is a missing item or any visible damage, notify your service provider or dealer immediately. 2.2 Prerequisites In order to install the SU-200BX, you will need the following items: (1) Power outlet Plug the SU-200BX directly into a wall outlet. Note: Data rates may be affected when using an extension cord or power strip. (2) Computer with 10/100 base-T Ethernet Network Interface Card This document is subject to change without prior notice. SU-200BX Installation Manual 2.3 Safety Precautions Please make sure to read the following instructions before handling the equipment. (1) Read all instructions before installing or operating the equipment. Be sure to keep this manual for further reference. (2) Please follow all the safety precautions and other installation procedures. (3) Do not use this product in the following environments: - Extremely high or low temperatures - High humidity areas or near water such as sinks or bathtubs - Areas where sudden changes in temperature occur - Under direct sunlight (4) Do not use this equipment near heaters or other devices that emit high heat. (5) Do not place heavy objects on top of the SU-200BX. (6) Turn off the SU-200BX and unplug the cord before cleaning. Do not use liquid or aerosol cleaners. (7) If water or any other liquid is spilled on the device, turn off the power and unplug the cord. Contact Xeline’s Technical Support Center. Continuing to use the device may cause fire or an electric shock. (8) Do not open, disassemble, or attempt to repair the device. If service or repair is required, contact Xeline’s Technical Support Center. Incorrect reassembly can cause electric shock when the equipment is subsequently used. (9) Replace only with same type and ratings of fuse. This document is subject to change without prior notice. SU-200BX Installation Manual 3. Getting to Know the SU-200BX 3.1 Front View Figure 3 SU-200BX Front View PWR Activates when power is turned on. ACT (PCS) Blinks when PLC signals are detected. SYNC (LINK) Blinks when the detected PLC signals are valid. LAN Activates when the SU-200BX LAN port is connected to the PC. Blinks during data transmission between the SU-200BX and the PC. 3.2 Rear View Reset button Figure 4 SU-200BX Rear View RJ-45 Port RJ-45 Ethernet port for connection with the PC. Reset Resets the SU-200BX to factory default mode. (Caution!) AC Inlet For connection to power cable. Power Switch Switch for turning power ON/OFF. This document is subject to change without prior notice. SU-200BX Installation Manual 3.3 Product Specifications Specifications Remarks Data rates Up to 24Mbps Interface RJ-45 Power AC 90V - 240V, 0.4A, 50/60Hz Dimensions 186 X 143 X 40mm Weight 206g For connection with NIC (W x D x H) 3.4 Minimal Requirements for the Subscriber’s PC CPU Intel Pentium 166MHz or higher Memory 32MB or more OS Windows 95, 98, ME, 2000, NT, XP Network Interface Card 10/100 base-T Ethernet Network Interface Card This document is subject to change without prior notice. SU-200BX Installation Manual 4. Installing the SU-200BX 4.1 Connecting the SU-200BX to the Subscriber’s PC ① Insert the RJ-45 cable into the RJ-45 Ethernet port of the SU-200BX. Figure 5 Connecting the RJ-45 cable and SU-200BX ② Insert the power cable into the AC inlet of the SU-200BX and plug the cable into a power outlet. Figure 6 Connecting the AC Power Cable 10 This document is subject to change without prior notice. SU-200BX Installation Manual ③ Connect the other end of the RJ-45 cable into the subscriber’s PC Network Interface Card. Figure 7 Connecting the SU-200BX to the Subscriber’s PC ④ Turn on the power of the SU-200BX and check if the LAN LED is activated. 4.2 Configuring the SU-200BX ① The SU-200BX is remotely configured by the EU-200BX through automatic process. Therefore there is no need to manually configure the SU-200BX1. ② Wait approximately 5 minutes for the EU-200BX to finish the remote registration process. Please refer to the EU-200BX Installation Guide for more details. 11 This document is subject to change without prior notice. SU-200BX Installation Manual 4.3 Configuring the Subscriber’s PC Note: The following IP setting example is based on Microsoft Windows 2000 Professional operating system. Configuration procedures may differ according to the subscriber PC O/S. ① Click the START button in your taskbar and go to NETWORK AND DIAL-UP CONNECTIONS. Go to: START Æ SETTINGS Æ NETWORK AND DIAL-UP CONNECTIONS Click Figure 8 Network and Dial-up Connections ② Right-click LOCAL AREA CONNECTION and select PROPERTIES. (1) Right-click (2) Click Figure 9 Local Area Connection Properties 12 This document is subject to change without prior notice. SU-200BX Installation Manual ③ Select INTERNET PROTOCOL (TCP/IP) and click [Properties]. Click Figure 10 Internet Protocol (TCP/IP) ④ Enter the IP address and DNS server address provided by the Internet Service Provider (ISP). i. For DHCP IP Addresses: Select OBTAIN AN IP ADDRESS AUTOMATICALLY. Then select the OBTAIN THE FOLLOWING DNS SERVER ADDRESS option. Click [OK] to continue. ii. For Fixed IP Addresses: Enter the addresses as shown in the example below. Click [OK]. Example IP address 211 168 11 249 255 255 255 128 211 168 11 129 Example DNS address 147 46 80 1 147 46 80 2 Click Figure 11 Fixed IP Address Setting 13 This document is subject to change without prior notice. SU-200BX Installation Manual ⑤ Select the SHOW ICON IN TASKBAR WHEN CONNECTED option and click [OK]. Click Figure 12 Show Icon in TaskBar ⑥ Configuring your computer for Internet connection is now complete. You can check your connection status by clicking the network icon in the taskbar as shown below. Figure 13 Network Configuration Complete 14 This document is subject to change without prior notice. SU-200BX Installation Manual 4.4 Final Check (Ping Test) Perform the following procedures in order to check if the installation is successful. ① Run Command window Go to: START Æ RUN.. Æ CMD Figure 14 Command Prompt Window ② Typeand press ENTER key Figure 15 Checking the Configured IP Address 15 This document is subject to change without prior notice. SU-200BX Installation Manual ③ ④ ⑤ In case of DHCP: - Physical Address : XX-XX-XX-XX-XX-XX Check - DHCP Enabled : Yes - IP Address : Check (Any IP) - Subnet Mask : Check (Any Subnet Mask) - Default Gateway : Check (Any Gateway) - DNS Servers : Check (Any DNS Servers) In case of Fixed IP: - Physical Address : XX-XX-XX-XX-XX-XX Check - Dhcp Enabled : No - IP Address : Check (Configured IP) - Subnet Mask : Check (Configured Subnet Mask) - Default Gateway : Check (Configured Gateway) - DNS Servers : Check (Configured DNS Servers) Check the default Gateway IP address and perform ping tests. The command is as follows: < ping Default Gateway IP –t > Figure 16 Pinging the Default Gateway IP 16 This document is subject to change without prior notice. SU-200BX Installation Manual ⑥ Installation is successful if the following message appears. < Reply from Default Gateway IP: bytes=32 time Figure 17 Checking the Ping Results 4.4 Resetting to Factory Default Mode Use the reset button at the back of the SU-200BX in order to reset the configuration into factory default mode. ① Turn off the power of the SU-200BX. ② Disconnect the RJ-45 cable. ③ Use a long sharp instrument (such as a pin) in order to push down on the reset button. ④ Turn on the SU-200BX while pushing down on the reset button. ⑤ Using the sharp instrument, push down on the reset button for 1 second. Wait at least 1 second before repeating the procedure at least 3 times or more. ⑥ The ACT LED will blink when the SU-200BX is changed to the factory default mode. ⑦ Reset the power of the SU-200BX. 17 This document is subject to change without prior notice. SU-200BX Installation Manual 5. Trouble Shooting Problem Checklist The POWER LED does not Check if the power cable is firmly plugged into the SU-200BX and activate. power outlet. The ACT and SYNC LEDs This can occur when the PLC link is not possible or the channel do not activate. conditions are poor. Try plugging the SU-200BX directly into a wall outlet. (When using a power strip, the other connected electrical appliances can affect the performance of the SU-200BX.) The LAN LED does not Check if the RJ-45 cable is firmly plugged into the SU-200BX and activate. the NIC of the PC. Check if the NIC connection is disabled in the Local Area Network window. Pinging to the default ① Check for typos in the ping command. Gateway IP is ② Check if the Gateway IP address is correct. unsuccessful. ③ Check the IP configuration of the subscriber’s PC. ④ If the IP configuration is correct, the problem lies in the ISP backbone. Check if it is possible to ping to a gateway at another location. The IP address does not (1) DHCP IP Address appear correctly in the ① Open the command prompt window. Type ‘ipconfig /renew’. ‘ipconfig /all’ command ② Type ‘ipconfig /all’ to recheck the IP address. prompt window. (2) Fixed IP Address ① Reconfigure the IP settings according the manual. ② Type ‘ipconfig /all’ to recheck the IP address. If the problem is still not solved, please contact Xeline’s Technical Support Center. 18 This document is subject to change without prior notice. SU-200BX Installation Manual 6. Appendix z Copyright 2005 Xeline Co., Ltd. All rights reserved. All Xeline brand product names are trademarks of Xeline Co., Ltd. Other product and company names mentioned herein are the trademarks of their respective owners. z Information in this document is subject to change without notice. No part of this document may be reproduced or altered in any form or by any means, electronical or mechanical, for any purpose, without the express written permission of Xeline Co., Ltd. z Xeline Technical Support Center Address: 5F. Seowon Bldg. 1515-4, Seocho3-dong, Seocho-gu, Seoul 137-871, Republic of Korea Telephone: +82 2 598 0980 Facsimile: +82 2 598 0975 E-mail: tech_support@xeline.com Website: http://www.xeline.com 19 This document is subject to change without prior notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 19 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:1cf2d1dd-95fd-455f-8a93-8ac0fd163213 Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2005:06:17 13:55:20+09:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2005:06:17 13:55:20+09:00 Document ID : uuid:ab4774c6-7d71-4f74-819e-2bbb3816dce0 Format : application/pdf Title : Microsoft Word - SU-200BX_Manual_eng_V08.doc Creator : simyunsong Author : simyunsongEXIF Metadata provided by EXIF.tools