Xi an NovaStar Tech EMT200 3D Emitter User Manual
Xi'an NovaStar Tech Co., Ltd 3D Emitter Users Manual
Users Manual
EMT200
3D Emitter
Product Version:
V1.0.0
Document Number:
NS110100634
Quick Start Guide
www.novastar.tech
i
Copyright © 2018 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved.
No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means
without the prior written consent of Xi’an NovaStar Tech Co., Ltd.
Trademark
is a trademark of Xi’an NovaStar Tech Co., Ltd.
Statement
You are welcome to use the product of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar).
This document is intended to help you understand and use the product. For accuracy and reliability,
NovaStar may make improvements and/or changes to this document at any time and without notice. Any
problem in use or any good suggestion, please contact us through ways provided in the document. We will
do our utmost to solve the problems and adopt the suggestions after evaluation as soon as possible.
FCC Caution
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
3D Emitter EMT200
Quick Start Guide
Change History
www.novastar.tech
ii
Change History
Version
Release Date
Description
V1.0.0
2018-08-16
First release
3D Emitter EMT200
Quick Start Guide
1 Overview
www.novastar.tech
1
1 Overview
The EMT200 is a 3D signal emitter from NovaStar designed for LED displays. The
emitter enables 3D display effect by working with 3D glasses and the controllers that
support 3D function.
Features
Obtains the 3D synchronization signal through Ethernet cables and can be
connected to receiving cards.
Supports a VESA 3D signal output connector connecting to a third-party external
emitter.
3D Emitter EMT200
Quick Start Guide
2 Appearance
www.novastar.tech
2
2 Appearance
Connector
Description
Ethernet port 1
Gigabit Ethernet port used for signal input or output.
Ethernet port 2
Gigabit Ethernet port used for signal input or output.
3D signal output
connector
Complies with VESA standard and connects to a third-party
external 3D emitter.
Power indicator
Always on: The power supply is normal.
3D signal indicator
Working statuses of the indicator:
Flashing every 1s: The EMT200 works normally.
Flashing every 3s: The EMT200 has no signal input.
Always on: A third-party external 3D emitter is connected.
Power connector
Connects to the provided power adapter to provide 5V DC
power supply.
3D Emitter EMT200
Quick Start Guide
3 Applications
www.novastar.tech
3
3 Applications
The EMT200 can be connected between the controller and receiving card, or
connected behind any of the receiving cards, making cabling flexible.
Note:
The controller in the application scenarios must support 3D function.
Only one EMT200 unit can be used in each application scenario.
3D Emitter EMT200
Quick Start Guide
3 Applications
www.novastar.tech
4
Application 1: EMT200 connected behind any of receiving cards
Application 2: EMT200 connected between controller and receiving card
3D Emitter EMT200
Quick Start Guide
4 3D Function Settings
www.novastar.tech
5
4 3D Function Settings
Step 1 Connect hardware devices according to the corresponding application described in
chapter 3 Applications. Application 1 is recommended.
Step 2 Enable 3D function by using any of the following methods and set 3D parameters.
Method 1: On LCD menu
On the LCD menu of the controller, choose Advanced Settings > 3D Settings
to enable the 3D function and set the video source format and eye priority.
Method 1: On NovaLCT
1. Start NovaLCT, choose Screen Configuration > Sending Card, select
Enable in 3D function area and click Settings to enter the 3D parameter
settings page.
2. Set 3D function parameters. Then, click Save to File to save the
parameters you set as a file. Or, you can click Load from File to load an
existing 3D configuration file.
3. On the screen configuration page, click Save to save current configuration
parameters to the controller.
3D Emitter EMT200
Quick Start Guide
4 3D Function Settings
www.novastar.tech
6
Step 3 Wear the provided 3D glasses and watch the images.
Step 4 (Optional) Enable the third-party external emitter.
On NovaLCT, select Enable third-party emitter and set Signal Delay Time.
Note:
If the third-party emitter is enabled, please wear the 3D glasses provided by the third
party and set Signal Delay Time to make sure that the signal of 3D glasses is in
sync with the display signal. The final 3D effect depends on the third-party emitter.
3D Emitter EMT200
Quick Start Guide
5 Firmware Update and Readback
www.novastar.tech
7
5 Firmware Update and Readback
EMT200 firmware update and readback must be operated on NovaLCT.
Update
Step 1 Start NovaLCT and choose Advanced Synchronous System User Login to log in
to the advanced user page.
Step 2 Type the secret code "admin" to enter the Program loading page.
Step 3 Click Browse to choose the program path, and then click Update.
Readback
Under Hardware Program Version Information, select Refresh All and click
Refresh.
3D Emitter EMT200
Quick Start Guide
6 Instructions for Provided 3D Glasses
www.novastar.tech
8
6 Instructions for Provided 3D Glasses
Set the switch of the 3D glasses to ON to turn on the 3D glasses. The red and
blue indicators will flash alternately.
When the 3D glasses detect 3D signal, the red and blue indicators go off.
After turned on, the 3D glasses can detect and connect to 3D signals within 30
meters of the EMT200 emitter.
After connected to the 3D signal, the 3D glasses can work morally within 50
meters of the EMT200 emitter.
After fully charged for 3.5 hours, the 3D glasses can provide up to 48 hours of
continuous use.
The DC 5V900mA USB charger is recommended for the provided 3D glasses.
You can also buy Optoma ZF2300 active shutter VESA 3D glasses to use.
When you use a third-party emitter and its 3D glasses, refer to the
corresponding instructions.
3D Emitter EMT200
Quick Start Guide
7 Dimensions
www.novastar.tech
9
7 Dimensions
Unit: mm
3D Emitter EMT200
Quick Start Guide
8 Specifications
www.novastar.tech
10
8 Specifications
Input voltage
DC 5V
Rated current
0.2 A
Rated power consumption
1 W
Dimensions
119.2 mm × 119.2 mm × 29.5 mm
Net weight
170.3 g
Work temperature
0~40℃
Packing information
Packing box: 380 mm × 200 mm × 100 mm
Outer container: 390 mm × 210 mm × 110 mm
1 × RJ45 Ethernet cable (1.5 m)
1 × DC power adapter (5V2A)
5 × pairs of 3D glasses
2 × sleeve anchors