Xiamen Padmate Technology X11 True wireless earbuds User Manual

Xiamen Padmate Technology Co.,LTD True wireless earbuds Users Manual

Contents

Users Manual

Instruction of X11 True Wireless earbudsThanks for purchasing Padmate X11 True Wireless earbuds. You will need to pair thedevice with your mobile phone or other Bluetooth enabled devices in order to experienceits great performance. Please read through the instruction manual below before using.I. IMPORTANCE BEFORE USING:The unit was designed and produced according to the related quality requests and safetystandards. Please read through the following operation instructions before using it:1. Read and keep well these instructions;2. Do not use or operate the it where it is forbidden of using, for example, airplanes andhospitals;3. Do not use or operate the it according to the local laws and rules, for example, do notuse it when driving;4. Do not use or operate it when you are close to explosive or flammable sources, eg,gas station etc;5. Do not hit or throw or open the unit by force as it may cause damage to the device;6. Do not put the unit near heat sources, eg, stoves, heat registers and radiators etc;7. Keep the unit away from wet, water or other liquids that might cause short circuit ormalfunctions;8. Keep the unit and its accessories away from children to prevent being swallowed9. For special users, such as patients who use heart pacemakers, audiphones andbuilt-in cochlea devices etc, please follow the advice of doctors.10. Using it below minus 15 ℃or above 55 ℃could shorten the life span of battery.II. About The Device2.1 Device controls and locations1、Multi Function button 2、LED indicator 3、Silicon earbuds 4、Power ON/OFF button5、Charging contact2.2 Packing listBluetooth headset (left & right) *1 pairCharging cradle with built power bank *1pcsInstruction manual *1pcsQuick start manual *1pcsMicro-USB cable *1pcsSilicon caps (L,M,S): 3 pairs
2.3 LED indications and modesEarbuds LED indications (Blue & Red)Pairing Blue and red glitter alternativelyPaired successfully Blue glitters 3 times and goes off. (Voice prompt“connected” can be heard)Playing music Blue LED color glitters slowlyLow battery Red LED glitters slowly. ( Beep indication can be heard)Charging Red LED on .Fully charged Red LED turns off and Blue LED turns on and will turn offwithin 5 seconds.Charging Cradle LED indications (Blue & Red)Low battery in cradle Red LED glitter slowlyCharged by USB Red LED onFully charged by USB Blue LED onCharging earbuds Red LED onEarbuds fully charged Blue LED on2.4 charging and batteryPlease use the original USB cable provided for charging.Warning: Using unmatched USB cable for charging might damage the device. Also, youare not permitted to take the battery out of the device in case of damage anddanger. Suggested input power is DC 5V, 100mA-2A max.III. Operations3.1 How to pairNOTE: The left and right headsets are paired already in factory. Users only need to paireither of the headset to mobile phone device and power on the other headset. Then thetwo headsets will both connect the mobile automatically. The selected headset for pairingwill be the master headset while slave-headset for the other one.1. Please take your mobile phone close to the device. Suggested distance is less than 1meter.2. Push On/Off button of either headset for 3 seconds, then you will see blue and red LEDglitter alternatively. Now it is ready for pairing.
3. Turn on the Bluetooth application of your mobile phone and click to search Bluetoothdevices near your mobile. Once searched “X11” device name, please select it to pair.After completely paired, blue LED will glitter slowly. Now the master headset isconnected!4. Press On/Off button of the other headset for 1 second to power it on. Now bothheadsets are connected and you can use your true wireless headset for music andphone call!3.2 Cancel the connection of the two headsets and use them as two separateheadsets1. When standby mode, press Multi Function Buttons of these two for 5 seconds, you willsee blue LEDs show fast for 3 seconds. Meanwhile voice prompt “right and leftearbuds disconnected” can be heard from headsets. Now they are two separatedheadsets. Repeat same operations (see 3.1) of pairing for respective connections todifferent mobile phones and you can use them separately.2. To get the two separated headsets to one pair: When standby mode, press MultiFunction Buttons of these two for 3 seconds, you will see blue LEDs show fast forre-connection. Once reconnected, blue LED will shine 3 seconds and voice prompt“right and left earbuds connected” can be heard from headsets.3.3 Multi-point pairingWay 1:Step 1: Pair the unit with the first mobile phone at first and turn off the Bluetoothof the mobile and power off the master headset.Step 2: Press On/Off button of the master headset for 3 seconds to turn it toparing mode again. Then pair the unit with your second mobile phone.Step 3: After paired with the second mobile phone, turn on the Bluetooth of thefirst mobile phone and you will find the X11 device name from the paring recordlist of the first mobile phone. Select the name again from the first mobile phoneand re-connect it. Now the unit connects the two mobile phones in the time.Way 2:Step 1: Pair the unit with the first mobile phone at first and turn off the Bluetoothof the mobile and power off the master headset.
Step 2: Press On/Off button of the master headset for 3 seconds to turn it toparing mode again. Then pair the unit with your second mobile phone.Step 3: After paired with the second mobile phone, power off the unit. Then turnon the Bluetooth of the first mobile phone and power on the unit again so that itwill automatically connect to the two mobile phones paired before.3.4 OperationsPower on Press Power On/Off button of the two headsets for1 secondBlue LED glitters twice andwith voice indication “poweron”Power off Press Power On/Off button of the two headsets for5 seconds when standbyRed LED glitters twice andwith voice indication “poweroff”Pairing Press On/Off button of either headset for 3seconds. After connected, it is the master headsetBlue and Red LED glittersalternatively and with voiceindication “pairing”Play Click Multi Function button of the master headsetPause Click again Multi Function button of the masterheadsetRe-dial the last phonenumber made beforeDouble click Multi Function button of the masterheadset(without music playing mode)Answer phone call Click Multi Function button of the master buttonwhen incoming callReject phone calls Double-click Multi Function button of the masterheadset when incoming call3.5 Cradle charging1. The cradle can supply up to three times charging to the two headsets once fullycharged.2. The LED in cradle will show red if only 8% capacity left.3. After putting headsets into the cradle, please press 2 seconds on the charging button atside of the cradle for charging. LED of cradle will glitter blue and turn to red. Once fullycharged, the LED of cradle will show blue.

Navigation menu