REPORT FORM XT 23G CE S
2017-12-18
: Xontel Xt-23G-Ce-S-Report XT-23G-CE-S-REPORT Certificates
Open the PDF directly: View PDF 
.
Page Count: 61
| Download | |
| Open PDF In Browser | View PDF |
Page 1 of 61 Test Report issued under the responsibility of: TEST REPORT IEC 60950-1 Information technology equipment – Safety – Part 1: General requirements Report Reference No........................ : RP20170711050 Date of issue.........................................: 2017-07-19 Total number of pages......................... 61 Applicant’s name............................... : SAHAB TECHNOLOGY Address................................................. : Ofiice 21,Qibla Tower,Fahad Al Salem St., Qibla,State of KUWAIT Manufacturer’s name........................: SAHAB TECHNOLOGY Address................................................. : Ofiice 21,Qibla Tower,Fahad Al Salem St., Qibla,State of KUWAIT Factory’s name...................................: N/A Address................................................. : N/A Test specification: Standard................................................: IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013 Test procedure..................................... : CE Non-standard test method…………..: N/A Test Report Form No........................ : IEC60950_1F Test Report Form(s) Originator......... : SGS Fimko Ltd Master TRF........................................... : Dated 2014-02 Test item description........................: IP PHONE Trade Mark............................................: Manufacturer.........................................: Model/Type reference......................... : SAHAB TECHNOLOGY XT-23G Ratings...................................................: Input:5Vdc,1.2A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 2 of 61 Report No.: RP20170711050 Testing procedure and testing location: Testing Laboratory Name: Testing location/ address......................... : Shenzhen Zoom Rel Testing Technology Co., Ltd. No.2 chuangyan Rd, Liuxian Avenue, Nanshan District Shenzhen. Tested by (name + signature)...... : Zhang Xiaoyang Approved by (+ signature)............ : Huang Pengfei .................................. Summary of testing: Tests performed (name of test and test clause): The submitted samples were found to comply with the requirements of: - IEC 60950-1:2005+A1:2009+A2:2013 - EN 60950-1:2006+A11:2009+A1:2010+A12:2011+ A2:2013 Testing location: Shenzhen Zoom Rel Testing Technology Co., Ltd. No.2 chuangyan Rd, Liuxian Avenue, Nanshan District Shenzhen. Summary of compliance with National Differences List of countries addressed: National Differences and Group Differences as per CB bulletin. The product fulfils the requirements of EN60950-1:2006 + A11:2009 + A1:2010+A12: 2011+A2:2013. Copy of marking plate: TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 3 of 61 Report No.: RP20170711050 Test item particulars..................................................... : Equipment mobility.......................................................... : [X] movable [] hand-held [] transportable [] stationary [] for building-in [] direct plug-in Connection to the mains.................................................: [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [X] not directly connected to the mains Operating condition......................................................... : [X] continuous [] rated operating / resting time: Access location ............................................................... : [X] operator accessible [] restricted access location Over voltage category (OVC) ....................................... : [] OVC I [] OVC II [X] other: [] OVC III [] OVC IV Mains supply tolerance (%) or absolute mains supply 5Vdc adapter power supply values ............................................................................... : Tested for IT power systems ........................................ : [] Yes [X] No IT testing, phase-phase voltage (V) .............................: N/A Class of equipment .........................................................: [] Class I [] Class II [] Not classified [X] Class III Considered current rating of protective device as part N/A of the building installlation (A) .......................................: Pollution degree (PD) .....................................................: [] PD 1 [X] PD 2 [] PD 3 IP protection class .......................................................... : IP20 Altitude during operation (m) ........................................ : <2000m Altitude of test laboratory (m) ....................................... : <500m Mass of equipment (kg) ................................................. : 1.3636Kg Possible test case verdicts: - test case does not apply to the test object.................. : N/A - test object does meet the requirement........................ : P (Pass) - test object does not meet the requirement..................: F (Fail) Testing.............................................................................. : Date of receipt of test item...............................................: 2017-07-05 Date(s) of performance of tests.......................................: 2017-07-05 to 2017-07-11 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a TRF No.: IEC60950_1F comma / point is used as the decimal separator. Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 4 of 61 Report No.: RP20170711050 General product information: The EUT is IP phone ,it used in 45degc operating temperature.it is by adapter power supply Following is the main board of XT-23G. TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 5 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 1 GENERAL P 1.5 Components P 1.5.1 General P Comply with IEC 60950-1 or relevant component standard (see appended table 1.5.1) P 1.5.2 Evaluation and testing of components Components which are certified to IEC and/or national standards are used correctly within their ratings. Components not covered by IEC standards are tested under the conditions present in the equipment. P 1.5.3 Thermal controls No such parts. N/A 1.5.4 Transformers (see Annex C) N/A 1.5.5 Interconnecting cables No interconnecting cables provided as part of the equipment. N/A 1.5.6 Capacitors bridging insulation No such capacity. N/A 1.5.7 Resistors bridging insulation No such components provided. N/A 1.5.7.1 Resistors bridging functional, basic or supplementary insulation N/A 1.5.7.2 Resistors bridging double or reinforced insulation between a.c. mains and other circuits N/A 1.5.7.3 Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable N/A 1.5.8 Components in equipment for IT power systems 1.5.9 Surge suppressors N/A 1.5.9.1 General N/A 1.5.9.2 Protection of VDRs N/A 1.5.9.3 Bridging of functional insulation by a VDR N/A 1.5.9.4 Bridging of basic insulation by a VDR N/A 1.5.9.5 Bridging of supplementary, double or reinforced insulation by a VDR N/A 1.6 Power interface 1.6.1 DC power distribution systems Not directly connect to DC main. N/A 1.6.2 Input current (see appended table 1.6.2) P 1.6.3 Voltage limit of hand-held equipment Movable equipment TRF No.: IEC60950_1F Not for use on IT systems. N/A P N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 6 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 1.6.4 Neutral conductor N/A 1.7 Marking and instructions P 1.7.1 Power rating and identification markings P 1.7.1.1 Power rating marking See below Multiple mains supply connections..........................: Single power supply Rated voltage(s) or voltage range(s) (V) .................: 5Vdc Symbol for nature of supply, for d.c. only.................: N/A P symbol used Rated frequency or rated frequency range (Hz)......: 1.7.1.2 P P N/A Rated current (mA or A) .............................................: 1.2A P Identification markings P See below Manufacturer’s name or trade-mark or identification Manufacturer’s name: mark ........................................................................: SAHAB TECHNOLOGY P Trademark: Model identification or type reference .....................: XT-23G Symbol for Class II equipment only ........................: Class III equipment Other markings and symbols ..................................: Additional markings are used and are defined in the installation instructions. P N/A P 1.7.1.3 Use of graphical symbols N/A 1.7.2 Safety instructions and marking Operating/safety instructions made available to the user. P 1.7.2.1 General See below P 1.7.2.2 Disconnect devices Class III equipment, not directly connect to mains. N/A 1.7.2.3 Overcurrent protective device Current limited by adaptor N/A 1.7.2.4 IT power distribution systems Not for IT system. N/A 1.7.2.5 Operator access with a tool No operator access areas require the use of a tool. N/A 1.7.2.6 Ozone No ozone emitted. N/A 1.7.3 Short duty cycles Equipment is designed for continuous operation. N/A 1.7.4 Supply voltage adjustment ....................................... : Power supplied by adaptor N/A Methods and means of adjustment; reference to installation instructions ..............................................: TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 7 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 1.7.5 Power outlets on the equipment ..............................: No power outlet. N/A 1.7.6 Fuse identification (marking, special fusing characteristics, cross-reference) ............................. : Power supplied by adaptor N/A 1.7.7 Wiring terminals N/A 1.7.7.1 Protective earthing and bonding terminals ............ : N/A 1.7.7.2 Terminals for a.c. mains supply conductors N/A 1.7.7.3 Terminals for d.c. mains supply conductors N/A 1.7.8 Controls and indicators N/A 1.7.8.1 Identification, location and marking ........................ : N/A 1.7.8.2 Colours ....................................................................... : N/A 1.7.8.3 Symbols according to IEC 60417............................ : N/A 1.7.8.4 Markings using figures ............................................ : N/A 1.7.9 Isolation of multiple power sources ........................: Single power supply N/A 1.7.10 Thermostats and other regulating devices ............: No such parts in the equipment N/A 1.7.11 Durability The labels were subjected to the permanence of marking test. P After tests,the labels remained legible and no show curling ,the marking on the label did not fade. 1.7.12 Removable parts No marking is located on removable parts N/A 1.7.13 Replaceable batteries .............................................. : No Replaceable batteries in the equipment N/A Language(s) ...............................................................: 1.7.14 Equipment for restricted access locations............. : The equipment is not intended to be installed in restricted access locations. N/A 2 PROTECTION FROM HAZARDS P 2.1 Protection from electric shock and energy hazards P 2.1.1 Protection in operator access areas Only SELV circuits are accessible. P 2.1.1.1 Access to energized parts See below P Test by inspection .......................................................: Complied P Test with test finger (Figure 2A) ............................... : The test finger can not contact bare hazardous parts. P TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 8 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Test with test pin (Figure 2B) .................................... : The test pin can not contact bare hazardous parts. Verdict P Test with test probe (Figure 2C) ...............................: No TNV circuit. N/A 2.1.1.2 Battery compartments N/A 2.1.1.3 Access to ELV wiring No battery compartment. N/A Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) (see appended table 2.10.5) 2.1.1.4 Access to hazardous voltage circuit wiring No accessible hazardous voltage circuit wiring. 2.1.1.5 Energy hazards ........................................................... : No energized part contains in equipment. N/A 2.1.1.6 Manual controls No knobs and the like are connected to parts at hazardous voltage. N/A 2.1.1.7 Discharge of capacitors in equipment SELV circuit N/A Measured voltage (V); time-constant (s).................. : 2.1.1.8 N/A Energy hazards – d.c. mains supply N/A a) Capacitor connected to the d.c. mains supply ...: N/A b) Internal battery connected to the d.c. mains supply ............................................................................: N/A 2.1.1.9 Audio amplifiers ...........................................................: No audio amplifiers N/A 2.1.2 Protection in service access areas N/A 2.1.3 Protection in restricted access locations 2.2 SELV circuits 2.2.1 General requirements 2.2.2 Voltages under normal conditions (V) ..................... : All accessible voltages are less than 42.4 Vp or 60 V dc and are classified as SELV. P 2.2.3 P 2.2.4 Voltages under fault conditions (V) .......................... : Under fault conditions voltages never exceed 71V peak and 120Vdc and do not exceed 42.4V peak or 60V dc for more than 0.2 sec. Connection of SELV circuits to other circuits ....... : SELV to SELV 2.3 TNV circuits P 2.3.1 Limits P TRF No.: IEC60950_1F Not intended for installation in restricted access locations. N/A P (see appended table 2.2) P P Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 9 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict Type of TNV circuits.................................................... : TNV-2 2.3.2 Separation from other circuits and from accessible parts P 2.3.2.1 General requirements P 2.3.2.2 Protection by basic insulation N/A 2.3.2.3 Protection by earthing N/A 2.3.2.4 Protection by other constructions .............................: N/A 2.3.3 Separation from hazardous voltages N/A 2.3.4 Insulation employed.....................................................: Connection of TNV circuits to other circuits P Insulation employed.....................................................: Other insulation 2.3.5 Test for operating voltages generated externally N/A 2.4 Limited current circuits N/A 2.4.1 General requirements 2.4.2 Limit values No limited current circuits N/A N/A Frequency (Hz).............................................................: Measured current (mA)............................................... : Measured voltage (V).................................................. : Measured circuit capacitance (nF or µF)................. : 2.4.3 Connection of limited current circuits to other circuits N/A 2.5 Limited power sources a) Inherently limited output (see appended table 2.5) N/A N/A b) Impedance limited output (see appended table 2.5) N/A N/A c) Regulating network limited output under normal operating and single fault condition d) Overcurrent protective device limited output (see appended table 2.5) N/A Max. output voltage (V), max. output current (A), max. apparent power (VA)......................................... : Current rating of overcurrent protective device (A) .: N/A Use of integrated circuit (IC) current limiters (See Annex CC) 2.6 Provisions for earthing and bonding N/A 2.6.1 Protective earthing N/A 2.6.2 Functional earthing N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 10 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict Use of symbol for functional earthing ...................: N/A 2.6.3 Protective earthing and protective bonding conductors N/A 2.6.3.1 General N/A 2.6.3.2 Size of protective earthing conductors N/A Rated current (A), cross-sectional area (mm ), AWG...............................................................................: 2 2.6.3.3 Size of protective bonding conductors N/A Rated current (A), cross-sectional area (mm2), AWG...............................................................................: Protective current rating (A), cross-sectional area (mm2), AWG..................................................................: 2.6.3.4 Resistance of earthing conductors and their terminations; resistance (), voltage drop (V), test current (A), duration (min).......................................... : N/A 2.6.3.5 Colour of insulation......................................................: N/A 2.6.4 Terminals N/A 2.6.4.1 General N/A 2.6.4.2 Protective earthing and bonding terminals N/A Rated current (A), type, nominal thread diameter (mm)...............................................................................: 2.6.4.3 Separation of the protective earthing conductor from protective bonding conductors N/A 2.6.5 Integrity of protective earthing N/A 2.6.5.1 Interconnection of equipment N/A 2.6.5.2 Components in protective earthing conductors and protective bonding conductors N/A 2.6.5.3 Disconnection of protective earth N/A 2.6.5.4 Parts that can be removed by an operator N/A 2.6.5.5 Parts removed during servicing N/A 2.6.5.6 Corrosion resistance N/A 2.6.5.7 Screws for protective bonding N/A 2.6.5.8 Reliance on telecommunication network or cable distribution system N/A 2.7 Overcurrent and earth fault protection in primary circuits N/A 2.7.1 Basic requirements N/A 2.7.2 No primary circuit. Instructions when protection relies on building installation N/A Faults not simulated in 5.3.7 N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 11 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 2.7.3 Short-circuit backup protection N/A 2.7.4 Number and location of protective devices ............ : N/A 2.7.5 Protection by several devices N/A 2.7.6 Warning to service personnel.................................... : N/A 2.8 Safety interlocks 2.8.1 General principles N/A N/A 2.8.2 Protection requirements N/A 2.8.3 Inadvertent reactivation N/A 2.8.4 Fail-safe operation N/A Protection against extreme hazard N/A 2.8.5 Moving parts N/A 2.8.6 Overriding N/A 2.8.7 Switches, relays and their related circuits N/A 2.8.7.1 Separation distances for contact gaps and their related circuits (mm)................................................: N/A 2.8.7.2 Overload test N/A 2.8.7.3 Endurance test N/A 2.8.7.4 Electric strength test 2.8.8 Mechanical actuators N/A 2.9 Electrical insulation N/A 2.9.1 Properties of insulating materials N/A 2.9.2 Humidity conditioning N/A No safety interlocks provided. (see appended table 5.2) Relative humidity (%), temperature (°C) ................. : N/A 2.9.3 Grade of insulation N/A 2.9.4 Separation from hazardous voltages N/A Method(s) used ........................................................... : 2.10 Clearances, creepage distances and distances through insulation N/A 2.10.1 General N/A 2.10.1.1 Frequency .................................................................... : N/A 2.10.1.2 Pollution degrees ........................................................ : N/A 2.10.1.3 Reduced values for functional insualtion N/A 2.10.1.4 Intervening unconnected conductive parts N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 12 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 2.10.1.5 Insulation with varying dimensions N/A 2.10.1.6 Special separation requirements N/A 2.10.1.7 Insulation in circuits generating starting pulses N/A 2.10.2 Determination of working voltage N/A 2.10.2.1 General N/A 2.10.2.2 RMS working voltage N/A 2.10.2.3 Peak working voltage N/A 2.10.3 Clearances N/A 2.10.3.1 General 2.10.3.2 Mains transient voltages N/A N/A a) AC mains supply .....................................................: N/A b) Earthed d.c. mains supplies ................................. : N/A c) Unearthed d.c. mains supplies ............................. : N/A d) Battery operation .................................................... : N/A 2.10.3.3 Clearances in primary circuits N/A 2.10.3.4 Clearances in secondary circuits N/A 2.10.3.5 Clearances in circuits having starting pulses N/A 2.10.3.6 Transients from a.c. mains supply ........................... : N/A 2.10.3.7 Transients from d.c. mains supply ........................... : N/A 2.10.3.8 Transients from telecommunication networks and cable distribution systems ......................................... : N/A 2.10.3.9 Measurement of transient voltage levels N/A a) Transients from a mains suplply N/A For an a.c. mains supply ............................................: N/A For a d.c. mains supply ..............................................: N/A b) Transients from a telecommunication network : N/A 2.10.4 Creepage distances N/A 2.10.4.1 General N/A 2.10.4.2 Material group and caomparative tracking index N/A CTI tests........................................................................ : 2.10.4.3 Minimum creepage distances N/A 2.10.5 Solid insulation N/A 2.10.5.1 General 2.10.5.2 Distances through insulation N/A N/A 2.10.5.3 Insulating compound as solid insulation N/A 2.10.5.4 Semiconductor devices N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 13 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 2.10.5.5. Cemented joints N/A 2.10.5.6 Thin sheet material – General N/A 2.10.5.7 Separable thin sheet material N/A Number of layers (pcs)................................................: 2.10.5.8 Non-separable thin sheet material N/A 2.10.5.9 Thin sheet material – standard test procedure N/A Electric strength test 2.10.5.10 Thin sheet material – alternative test procedure N/A Electric strength test 2.10.5.11 Insulation in wound components N/A 2.10.5.12 Wire in wound components N/A Working voltage ...........................................................: N/A a) Basic insulation not under stress ......................... : N/A b) Basic, supplemetary, reinforced insulation ........ : N/A c) Compliance with Annex U ..................................... : N/A Two wires in contact inside wound component; angle between 45 and 90 ....................................... : N/A Wire with solvent-based enamel in wound components N/A Electric strength test Routine test N/A Additional insulation in wound components N/A Working voltage ...........................................................: N/A - Basic insulation not under stress ........................... : N/A - Supplemetary, reinforced insulation ...................... : N/A 2.10.6 Construction of printed boards N/A 2.10.6.1 Uncoated printed boards N/A 2.10.6.2 Coated printed boards N/A 2.10.6.3 Insulation between conductors on the same inner surface of a printed board N/A 2.10.6.4 Insulation between conductors on different layers of a printed board N/A Distance through insulation N/A Number of insulation layers (pcs)..............................: N/A 2.10.7 Component external terminations N/A 2.10.8 Tests on coated printed boards and coated components N/A 2.10.5.13 2.10.5.14 TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 14 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 2.10.8.1 Sample preparation and preliminary inspection N/A 2.10.8.2 Thermal conditioning N/A 2.10.8.3 Electric strength test N/A 2.10.8.4 Abrasion resistance test N/A 2.10.9 Thermal cycling N/A 2.10.10 Test for Pollution Degree 1 environment and insulating compound N/A 2.10.11 Tests for semiconductor devices and cemented joints N/A 2.10.12 Enclosed and sealed parts N/A 3 WIRING, CONNECTIONS AND SUPPLY P 3.1 General P 3.1.1 Current rating and overcurrent protection P 3.1.2 Protection against mechanical damage The wires are routed away from sharp edges and parts which could damage insulation. P 3.1.3 Securing of internal wiring The wires are positioned in such a manner that prevents excessive strain, loosening of terminal connections and damage of conductor insulation. N/A 3.1.4 Insulation of conductors Insulation on internal conductor are considered to be of adequate quality and suitable for the application and the working voltages involved. N/A 3.1.5 Beads and ceramic insulators No beads or similar ceramic insulators on conductors. N/A 3.1.6 Screws for electrical contact pressure No screws for electrical contact pressure. N/A 3.1.7 Insulating materials in electrical connections No contact pressure through insulating material. N/A 3.1.8 Self-tapping and spaced thread screws Thread-cutting or space thread screws are not used for electrical connections. Machine screws only. N/A 3.1.9 Termination of conductors N/A 10 N pull test N/A Sleeving on wiring N/A 3.1.10 TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 15 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 3.2 Connection to a mains supply N/A 3.2.1 Means of connection 3.2.1.1 Connection to an a.c. mains supply N/A 3.2.1.2 Connection to a d.c. mains supply N/A 3.2.2 Multiple supply connections 3.2.3 Permanently connected equipment Not directly connect to mains Single power supply. The equipment is not permanently connected. See clause 3.2.1.1 and 3.3. Number of conductors, diameter of cable and conduits (mm) ..............................................................: N/A N/A N/A 3.2.4 Appliance inlets N/A 3.2.5 Power supply cords N/A 3.2.5.1 AC power supply cords N/A Type .............................................................................. : Rated current (A), cross-sectional area (mm ), AWG ............................................................................. : 2 3.2.5.2 DC power supply cords N/A 3.2.6 Cord anchorages and strain relief N/A Mass of equipment (kg), pull (N) .............................: Longitudinal displacement (mm) .............................. : 3.2.7 Protection against mechanical damage N/A 3.2.8 Cord guards N/A Diameter or minor dimension D (mm); test mass (g) ........................................................................................ : Radius of curvature of cord (mm)..............................: 3.2.9 Supply wiring space N/A 3.3 Wiring terminals for connection of external conductors N/A 3.3.1 Wiring terminals N/A 3.3.2 Connection of non-detachable power supply cords N/A 3.3.3 Screw terminals N/A 3.3.4 Conductor sizes to be connected N/A Rated current (A), cord/cable type, cross-sectional area (mm2).................................................................... : 3.3.5 Wiring terminal sizes N/A Rated current (A), type, nominal thread diameter (mm) ..............................................................................: TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 16 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 3.3.6 Wiring terminal design N/A 3.3.7 Grouping of wiring terminals N/A 3.3.8 Stranded wire N/A 3.4 Disconnection from the mains supply N/A 3.4.1 General requirement 3.4.2 Disconnect devices 3.4.3 Permanently connected equipment Not permanently connected equipment. N/A 3.4.4 Parts which remain energized No parts remain energized after the disconnect device is switched off. N/A 3.4.5 Switches in flexible cords No isolating switch in the cord set. N/A 3.4.6 Number of poles - single-phase and d.c. equipment N/A 3.4.7 Number of poles - three-phase equipment N/A 3.4.8 Switches as disconnect devices N/A 3.4.9 Plugs as disconnect devices N/A 3.4.10 Interconnected equipment N/A 3.4.11 Multiple power sources 3.5 Interconnection of equipment 3.5.1 General requirements See below P 3.5.2 Types of interconnection circuits ..............................: SELV to SELV P 3.5.3 ELV circuits as interconnection circuits No ELV circuit N/A 3.5.4 Data ports for additional equipment P 4 PHYSICAL REQUIREMENTS P 4.1 Stability N/A Angle of 10 N/A Test force (N) ...............................................................: Not floor-standing equipment. N/A Not directly connect to mains N/A N/A Single power supply only. N/A P 4.2 Mechanical strength 4.2.1 General Class Ⅲ equipment. N/A Rack-mounted equipment. (see Annex DD) N/A 4.2.2 Steady force test, 10 N TRF No.: IEC60950_1F P Complied P Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 17 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 4.2.3 Steady force test, 30 N N/A 4.2.4 Steady force test, 250 N 4.2.5 Impact test N/A Fall test N/A Swing test N/A Complied 4.2.6 Drop test; height (mm) ............................................... : Height:750mm, 3 times, no hazard 4.2.7 Stress relief test 4.2.8 Cathode ray tubes P P N/A No CRT provided. N/A N/A No high pressure lamp. N/A Picture tube separately certified ............................... : 4.2.9 High pressure lamps 4.2.10 Wall or ceiling mounted equipment; force (N) ........ : 4.3 Design and construction 4.3.1 Edges and corners 4.3.2 Handles and manual controls; force (N).................: 4.3.3 Adjustable controls 4.3.4 Securing of parts Parts are reliably secured P 4.3.5 Connection by plugs and sockets SELV connectors do not comply with IEC 60320 or IEC 60083. P 4.3.6 Direct plug-in equipment Not direct plug-in equipment N/A P Round and smooth No knobs, grips, handles, lever etc. The equipment is autoranging. P N/A N/A N/A Torque ......................................................................... : Compliance with the relevant mains plug standard ...................................................................... : N/A 4.3.7 Heating elements in earthed equipment The equipment does not have any heating elements. N/A 4.3.8 Batteries The equipment does not have any batteries. N/A - Overcharging of a rechargeable battery N/A - Unintentional charging of a non-rechargeable battery N/A - Reverse charging of a rechargeable battery N/A - Excessive discharging rate for any battery N/A 4.3.9 Oil and grease N/A 4.3.10 Dust, powders, liquids and gases TRF No.: IEC60950_1F Equipment in intended use not considered to be exposed to these. N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 18 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 4.3.11 Containers for liquids or gases The equipment does not contain liquids. N/A 4.3.12 Flammable liquids ......................................................: The equipment does not use any flammable liquids. N/A Quantity of liquid (l) ....................................................: N/A Flash point (C) .......................................................... : N/A 4.3.13 Radiation 4.3.13.1 General 4.3.13.2 Ionizing radiation 4.3.13.3 P Indicating LED only P N/A Measured radiation (pA/kg) ......................................: Measured high-voltage (kV) .....................................: Measured focus voltage (kV) ................................... : CRT markings ............................................................ : N/A Effect of ultraviolet (UV) radiation on materials No ultraviolet radiation. Part, property, retention after test, flammability classification ............................................................... : N/A 4.3.13.4 Human exposure to ultraviolet (UV) radiation ....... : N/A 4.3.13.5 Lasers (including laser diodes) and LEDs 4.3.13.5.1 Lasers (including laser laser diodes) Indicating LED only P N/A Laser class ..................................................................: 4.3.13.5.2 Light emitting diodes (LEDs) P 4.3.13.6 Other types ................................................................. : N/A 4.4 Protection against hazardous moving parts 4.4.1 General N/A N/A 4.4.2 Protection in operator access areas ....................... : N/A Household and home/office document/media shredders N/A 4.4.3 Protection in restricted access locations ................: N/A 4.4.4 Protection in service access areas N/A 4.4.5 Protection against moving fan blades 4.4.5.1 General N/A N/A Not considered to cause pain or injury. a)………….: N/A Is considered to cause pain, not injury. b) …………: N/A Considered to cause injury. c) …………: N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 19 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause 4.4.5.2 4.4.5.3 Requirement + Test Result - Remark Verdict Protection for users N/A Use of symbol or warning ………………...…………: N/A Protection for service persons N/A Use of symbol or warning ……………………...……: N/A 4.5 Thermal requirements P 4.5.1 General The equipment and its components did not attain excessive temperatures during normal operation. P 4.5.2 Temperature tests (see appended table 4.5) P Normal load condition per Annex L .........................: 4.5.3 Temperature limits for materials (see appended table 4.5) P 4.5.4 Touch temperature limits (see appended table 4.5) P 4.5.5 Resistance to abnormal heat ................................... : (see appended table 4.5.5) 4.6 Openings in enclosures 4.6.1 Top and side openings P No openings Dimensions (mm) .......................................................: 4.6.2 N/A Bottoms of fire enclosures N/A Complied Construction of the bottomm, dimensions (mm) ...: P 4.6.3 Doors or covers in fire enclosures No doors. N/A 4.6.4 Openings in transportable equipment Not transportable. N/A 4.6.4.1 Constructional design measures N/A Dimensions (mm) .......................................................: 4.6.4.2 Evaluation measures for larger openings N/A 4.6.4.3 Use of metallized parts N/A 4.6.5 Adhesives for constructional purposes N/A Conditioning temperature (C), time (weeks)......... : 4.7 Resistance to fire P 4.7.1 Reducing the risk of ignition and spread of flame Use of materials with the required flammability classes. P Method 1, selection and application of components (see appended table 4.7) wiring and materials P TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 20 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Method 2, application of all of simulated fault condition tests Method 1 used Verdict N/A 4.7.2 Conditions for a fire enclosure P 4.7.2.1 Parts requiring a fire enclosure P 4.7.2.2 Parts not requiring a fire enclosure 4.7.3 Materials 4.7.3.1 General 4.7.3.2 Materials for fire enclosures N/A 4.7.3.3 Materials for components and other parts outside fire enclosures N/A 4.7.3.4 Materials for components and other parts inside fire enclosures At least of flammability class V-2 or HF-2. 4.7.3.5 Materials for air filter assemblies The equipment does not have any air filters. N/A 4.7.3.6 Materials used in high-voltage components No high voltage component. N/A 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS N/A 5.1 Touch current and protective conductor current 5.1.1 General N/A N/A 5.1.2 Configuration of equipment under test (EUT) N/A 5.1.2.1 Single connection to an a.c. mains supply N/A 5.1.2.2 Redundant multiple connections to an a.c. mains supply N/A 5.1.2.3 Simultaneous multiple connections to an a.c. mains supply N/A 5.1.3 Test circuit N/A 5.1.4 Application of measuring instrument N/A 5.1.5 Test procedure N/A 5.1.6 Test measurements N/A N/A P All components are mounted on the PCB of min. V-1. P P Supply voltage (V) ..................................................... : Measured touch current (mA) .................................. : Max. allowed touch current (mA) .............................: Measured protective conductor current (mA) ........: Max. allowed protective conductor current (mA)... : 5.1.7 Equipment with touch current exceeding 3,5 mA N/A 5.1.7.1 General ........................................................................: N/A 5.1.7.2 Simultaneous multiple connections to the supply N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 21 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict 5.1.8 Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks N/A 5.1.8.1 Limitation of the touch current to a telecommunication network or to a cable distribution system N/A 5.1.8.2 Supply voltage (V) ..................................................... : Measured touch current (mA) .................................. : Max. allowed touch current (mA) .............................: Summation of touch currents from telecommunication networks N/A a) EUT with earthed telecommunication ports ...... : N/A b) EUT whose telecommunication ports have no reference to protective earth N/A 5.2 Electric strength 5.2.1 General 5.2.2 Test procedure P 5.3 Abnormal operating and fault conditions P 5.3.1 Protection against overload and abnormal operation (see appended table 5.3) P 5.3.2 Motors (see appended Annex B) N/A 5.3.3 Transformers (see appended Annex C) N/A 5.3.4 Functional insulation...................................................: 5.3.5 Electromechanical components N/A 5.3.6 Audio amplifiers in ITE .............................................. : N/A 5.3.7 Simulation of faults 5.3.8 Unattended equipment 5.3.9 Compliance criteria for abnormal operating and fault conditions P 5.3.9.1 During the tests P 5.3.9.2 After the tests P 6 CONNECTION TO TELECOMMUNICATION NETWORKS N/A 6.1 Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment N/A 6.1.1 Protection from hazardous voltages N/A 6.1.2 Separation of the telecommunication network from earth N/A TRF No.: IEC60950_1F P (see appended table 5.2) P P (see appended table 5.3) P N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 22 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause 6.1.2.1 Requirement + Test Result - Remark Requirements (see appended table 5.2) Verdict N/A Supply voltage (V) ..................................................... : Current in the test circuit (mA) ...............................: 6.1.2.2 Exclusions ...................................................................: N/A 6.2 Protection of equipment users from overvoltages on telecommunication networks N/A 6.2.1 Separation requirements N/A 6.2.2 Electric strength test procedure N/A 6.2.2.1 Impulse test (see appended table 5.2) N/A 6.2.2.2 Steady-state test (see appended table 5.2) N/A 6.2.2.3 Compliance criteria N/A 6.3 Protection of the telecommunication wiring system from overheating N/A Max. output current (A) ............................................. : Current limiting method .............................................: 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS N/A 7.1 General N/A 7.2 Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 Protection of equipment users from overvoltages on the cable distribution system N/A 7.4 Insulation between primary circuits and cable distribution systems N/A 7.4.1 General N/A 7.4.2 Voltage surge test (see appended table 5.2) N/A 7.4.3 Impulse test (see appended table 5.2) N/A A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE N/A A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see 4.7.3.2) N/A A.1.1 Samples........................................................................: Wall thickness (mm)................................................... : Conditioning of samples; temperature (C) ........... : N/A A.1.2 TRF No.: IEC60950_1F No connection to CABLE DISTRIBUTION SYSTEMS. N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 23 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict A.1.3 Mounting of samples ................................................. : N/A A.1.4 Test flame (see IEC 60695-11-3) N/A Flame A, B, C or D .................................................... : A.1.5 Test procedure N/A A.1.6 Compliance criteria N/A Sample 1 burning time (s)......................................... : Sample 2 burning time (s)......................................... : Sample 3 burning time (s)......................................... : A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see 4.7.3.2 and 4.7.3.4) A.2.1 Samples, material....................................................... : Wall thickness (mm)................................................... : A.2.2 Conditioning of samples; temperature (°C) ........... : N/A A.2.3 Mounting of samples ................................................. : N/A A.2.4 Test flame (see IEC 60695-11-4) N/A Flame A, B or C ..........................................................: N/A A.2.5 Test procedure N/A A.2.6 Compliance criteria N/A A.2.7 Sample 1 burning time (s)......................................... : Sample 2 burning time (s)......................................... : Sample 3 burning time (s)......................................... : Alternative test acc. to IEC 60695-11-5, cl. 5 and 9 N/A Sample 1 burning time (s)......................................... : Sample 2 burning time (s)......................................... : Sample 3 burning time (s)......................................... : A.3 Hot flaming oil test (see 4.6.2) N/A A.3.1 Mounting of samples N/A A.3.2 Test procedure N/A A.3.3 Compliance criterion N/A B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and 5.3.2) N/A B.1 General requirements N/A Position ........................................................................: Manufacturer .............................................................. : TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 24 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict Type ............................................................................. : Rated values ..............................................................: N/A B.2 Test conditions B.3 Maximum temperatures (see appended table 5.3) N/A B.4 Running overload test (see appended table 5.3) N/A B.5 Locked-rotor overload test N/A Test duration (days) .................................................. : Electric strength test: test voltage (V) .....................: B.6 Running overload test for d.c. motors in secondary circuits N/A B.6.1 General N/A B.6.2 Test procedure N/A B.6.3 Alternative test procedure N/A B.6.4 Electric strength test; test voltage (V) .....................: N/A B.7 Locked-rotor overload test for d.c. motors in secondary circuits N/A B.7.1 General N/A B.7.2 Test procedure N/A B.7.3 Alternative test procedure N/A B.7.4 Electric strength test; test voltage (V) ....................: N/A B.8 Test for motors with capacitors (see appended table 5.3) N/A B.9 Test for three-phase motors (see appended table 5.3) N/A B.10 Test for series motors N/A Operating voltage (V) ................................................ : C ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3) N/A Position ........................................................................: Manufacturer .............................................................. : Type ............................................................................. : Rated values ..............................................................: Method of protection.................................................. : N/A C.1 Overload test (see appended table 5.3) C.2 Insulation (see appended tables 5.2 and C2) Protection from displacement of windings.............. : TRF No.: IEC60950_1F N/A N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 25 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) N/A D.1 Measuring instrument N/A D.2 Alternative measuring instrument N/A E ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13) N/A F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES (see 2.10 and Annex G) N/A G ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES N/A G.1 Clearances N/A G.1.1 General N/A G.1.2 Summary of the procedure for determining minimum clearances N/A G.2 Determination of mains transient voltage (V) N/A G.2.1 AC mains supply ........................................................ : N/A G.2.2 Earthed d.c. mains supplies .....................................: N/A G.2.3 Unearthed d.c. mains supplies ................................ : N/A G.2.4 Battery operation ........................................................: N/A G.3 Determination of telecommunication network transient voltage (V) ............................................... : N/A G.4 Determination of required withstand voltage (V) N/A G.4.1 Mains transients and internal repetitive peaks ......: N/A G.4.2 Transients from telecommunication networks .......: N/A G.4.3 Combination of transients N/A G.4.4 Transients from cable distribution systems N/A G.5 Measurement of transient voltages (V) N/A a) Transients from a mains supply N/A For an a.c. mains supply N/A For a d.c. mains supply N/A b) Transients from a telecommunication network N/A G.6 Determination of minimum clearances ............. : N/A H ANNEX H, IONIZING RADIATION (see 4.3.13) N/A J ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6) N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 26 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Metal(s) used ..............................................................: Verdict K ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8) K.1 Making and breaking capacity N/A N/A K.2 Thermostat reliability; operating voltage (V) ..........: N/A K.3 Thermostat endurance test; operating voltage (V) ................................................................................: N/A K.4 Temperature limiter endurance; operating voltage (V) .................................................................................: N/A K.5 Thermal cut-out reliability N/A K.6 Stability of operation L ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2) N/A L.1 Typewriters N/A L.2 Adding machines and cash registers N/A L.3 Erasers N/A L.4 Pencil sharpeners N/A L.5 Duplicators and copy machines N/A L.6 Motor-operated files N/A L.7 Other business equipment N/A M ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1) M.1 Introduction N/A N/A M.2 Method A N/A M.3 Method B N/A M.3.1 Ringing signal N/A M.3.1.1 Frequency (Hz) .......................................................... : M.3.1.2 Voltage (V) .................................................................. : M.3.1.3 Cadence; time (s), voltage (V) .................................: M.3.1.4 Single fault current (mA) ...........................................: M.3.2 Tripping device and monitoring voltage ................. : N/A M.3.2.1 Conditions for use of a tripping device or a monitoring voltage N/A M.3.2.2 Tripping device N/A M.3.2.3 Monitoring voltage (V) ...............................................: N/A TRF No.: IEC60950_1F (see appended table 5.3) N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 27 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict N ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1, 7.3.2, 7.4.3 and Clause G.5) N/A N.1 ITU-T impulse test generators N/A N.2 IEC 60065 impulse test generator N/A P ANNEX P, NORMATIVE REFERENCES Q ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1) a) Preferred climatic categories ...............................: N/A N/A b) Maximum continuous voltage ..............................: N/A c) Pulse current .......................................................... : N/A R ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL PROGRAMMES N/A R.1 Minimum separation distances for unpopulated coated printed boards (see 2.10.6.2) N/A R.2 Reduced clearances (see 2.10.3) N/A S ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3) S.1 Test equipment N/A N/A S.2 Test procedure N/A S.3 Examples of waveforms during impulse testing N/A T ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER (see 1.1.2) N/A U ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED INSULATION (see 2.10.5.4) N/A V ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1) N/A V.1 Introduction N/A V.2 TN power distribution systems N/A W ANNEX W, SUMMATION OF TOUCH CURRENTS W.1 Touch current from electronic circuits N/A N/A W.1.1 Floating circuits N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 28 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict W.1.2 Earthed circuits N/A W.2 Interconnection of several equipments N/A W.2.1 Isolation N/A W.2.2 Common return, isolated from earth N/A W.2.3 Common return, connected to protective earth N/A X ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause C.1) N/A X.1 Determination of maximum input current N/A X.2 Overload test procedure N/A Y ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3) Y.1 Test apparatus ........................................................... : N/A N/A Y.2 Mounting of test samples ..........................................: N/A Y.3 Carbon-arc light-exposure apparatus .....................: N/A Y.4 Xenon-arc light exposure apparatus .......................: N/A Z ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2) N/A AA ANNEX AA, MANDREL TEST (see 2.10.5.8) N/A BB ANNEX BB, CHANGES IN THE SECOND EDITION CC Annex CC, Evaluation of integrated circuit (IC) current limiters N/A CC.1 General N/A CC.2 Test program 1………………….............………….: N/A CC.3 Test program 2……………………….........……….: N/A CC.4 Test program 3.....................................................: N/A CC.5 Compliance..........................................................: N/A DD Annex DD, Requirements for the mounting means of rack-mounted equipment N/A DD.1 General: N/A DD.2 Mechanical strength test, variable N……..…..:: N/A DD.3 Mechanical strength test, 250N, including end stops……………………………………………...: N/A DD.4 Compliance……………………………....………: N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 29 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict EE Annex EE, Household and home/office document/media shredders EE.1 General: N/A N/A EE.2 Markings and instructions N/A Use of markings or symbols………...…………: N/A Information of user instructions, maintenance and/or servicing instructions……………………: N/A EE.3 Inadvertent reactivation test………………....…: N/A EE.4 Disconnection of power to hazardous moving parts: N/A Use of markings or symbols……………………: N/A Protection against hazardous moving parts N/A Test with test finger (Figure 2A) ………………: N/A Test with wedge probe (Figure EE1 and EE2).: N/A EE.5 TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 30 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause 1.5.1 Requirement + Test Result - Remark TABLE: List of critical components P Object/part No. Manufacturer/ Type/model Technical data trademark PCB Interchangeable Interchangeable V-0,105°C RJ11 jack Interchangeable Interchangeable RJ11 Internal Wiring Interchangeable Interchangeable Min. VW-1,80℃ Min. HB, Enclosure Interchangeable Interchangeable min.85℃ Input: AC100240V, 50/60Hz 0.18A Adapter Interchangeable Interchangeable Output:DC5V 12 00mA,complied with LPS. Supplementary information: 1) Verdict Standard (Edition / year) UL 796 -UL 758 Mark(s) of conformity1) UL UL UL UL 94 UL EN 60950-1 CE NB Provided evidence ensures the agreed level of compliance. See OD-CB2039. 1.5.1 TABLE: Opto Electronic Devices N/A Manufacturer..................................................... : Type....................................................................: Separately tested............................................. : Bridging insulation............................................ : External creepage distance............................ : Internal creepage distance............................. : Distance through insulation............................ : Tested under the following conditions...........: Input....................................................................: Output.................................................................: supplementary information 1.6.2 TABLE: Electrical data (in normal conditions) P U (V) I (A) Irated (A) P (W) Fuse # Ifuse (A) 5Vdc 0.029A 1.2A 2.574W - - TRF No.: IEC60950_1F Condition/status The EUT in normal operating conditions. Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 31 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict Supplementary information: 2.1.1.5 c) 1) N/A TABLE: max. V, A, VA test Voltage (rated) (V) Current (rated) (A) Voltage (max.) (V) Current (max.) (A) VA (max.) (VA) supplementary information: 2.1.1.5 c) 2) N/A TABLE: stored energy Capacitance C (µF) Voltage U (V) Energy E (J) supplementary information: 2.2 TABLE: evaluation of voltage limiting components in SELV circuits Component (measured between) max. voltage (V) (normal operation) V peak Fault test performed on voltage limiting components N/A Voltage Limiting Components V d.c. Voltage measured (V) in SELV circuits (V peak or V d.c.) supplementary information: 2.5 TABLE: limited power sources N/A Circuit output tested: Note: Measured Uoc (V) with all load circuits disconnected: Components Sample No, Uoc (V) Isc (A) Meas. VA Limit Meas. Limit supplementary information: Sc=Short circuit, Oc=Open circuit TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 32 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test 2.10.2 Table: working voltage measurement Location Result - Remark RMS voltage (V) Verdict N/A Peak voltage (V) Comments supplementary information: 2.10.3 and 2.10.4 TABLE: Clearance and creepage distance measurements Clearance (cl) and creepage distance (cr) at/of/between: U peak (V) U r.m.s. (V) Required cl (mm) cl (mm) N/A Required cr (mm) cr (mm) Functional: Basic/supplementary: Reinforced: Supplementary information: 2.10.5 TABLE: Distance through insulation measurements Distance through insulation (DTI) at/of: U peak (V) U rms (V) N/A Test voltage (V) Required DTI (mm) DTI (mm) Supplementary information: TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 33 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause 2.10.5 Requirement + Test Result - Remark TABLE: Distance through insulation measurements Distance through insulation (DTI) at/of: 4.3.8 Verdict U peak (V) U rms (V) N/A Test voltage (V) Required DTI (mm) TABLE: Batteries DTI (mm) N/A The tests of 4.3.8 are applicable only when appropriate battery data is not available Is it possible to install the battery in a reverse polarity position? Non-rechargeable batteries Discharging Meas. current Manuf. Specs. Unintentional charging Rechargeable batteries Charging Meas. current Discharging Manuf. Specs. Meas. current Manuf. Specs. Reversed charging Meas. current Manuf. Specs. Max. current during normal condition Max. current during fault condition Test results: Verdict - Chemical leaks - Explosion of the battery - Emission of flame or expulsion of molten metal - Electric strength tests of equipment after completion of tests Supplementary information: 4.3.8 TABLE: Batteries Battery category............................................... : N/A (Lithium, NiMh, NiCad, Lithium Ion …) Manufacturer..................................................... : Type / model..................................................... : Voltage............................................................... : Capacity............................................................. : mAh Tested and Certified by (incl. Ref. No.).........: Circuit protection diagram: TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 34 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Verdict MARKINGS AND INSTRUCTIONS (1.7.12, 1.7.15) Location of replaceable battery Language(s) ………………………………….: Close to the battery ………………………….: In the servicing instructions …………………: In the operating instructions ………………..: 4.5 TABLE: Thermal requirements P Supply voltage (V) ..............................: 5Vdc - Ambient Tmin (C) ................................ : 45.0 - Ambient Tmax (C) ................................: 45.0 - Maximum measured temperature T of part/at:: Allowed Tmax (C) X8 D1 C25 D8 VD13 D2 D3 Key board Surface T1 T2 D9 S1 D15 C2 LCD surface D2 PCB Receiver surface VD1 Ambient Supplementary information: Temperature T of winding: TRF No.: IEC60950_1F 51.6 53.1 64.1 80.8 53.0 61.7 61.1 51.0 49.1 51.4 58.2 61.7 46.6 73.2 53.9 55.3 60.5 67.1 46.6 58.2 45.0 t1 (°C) R1 () t2 (°C) R2 () T (C) Allowed Tmax (C) 130.0 130.0 105.0 130.0 130.0 130.0 130.0 85.0 70.0 105.0 130.0 130.0 85.0 130.0 105.0 85.0 130.0 130. 85.0 130.0 Insulatio n class Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 35 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test - Result - Remark - - - - Verdict - - - Supplementary information: 4.5.5 TABLE: Ball pressure test of thermoplastic parts Allowed impression diameter (mm) ........................: N/A 2 mm Part Test temperature Impression diameter (mm) (C) Supplementary information: 4.7 TABLE: Resistance to fire Part Manufacturer of material N/A Type of material Thickness (mm) Flammability class Evidence Supplementary information: 5.1 TABLE: Touch current measurement Measured between: Measured (mA) N/A Limit (mA) Comments/conditions supplementary information: 5.2 TABLE: Electric strength tests, impulse tests and voltage surge tests Test voltage applied between: Voltage shape Test voltage (AC, DC, (V) impulse, surge) P Breakdown Yes / No Functional: - - - - DC 1000V No - - - Basic/supplementary: Telephone port to handset Reinforced: Supplementary information: 5.3 TABLE: Fault condition tests P Ambient temperature (C) ........................................: 25°C Power source for EUT: Manufacturer, model/type, output rating ...............................................................: See tabel 1.5.1. TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 36 of 61 Report No.: RP20170711050 IEC 60950-1/Am1 Clause Requirement + Test Result - Remark Component No. Fault Supply voltage (V) Test time Fuse # Fuse current (A) Opening BL 5Vdc 130min - - Verdict Observation No explosion. 46.9 °C. no fire, no smoke, No hazard. Supplementary information: SC: short-circuit; OC: open-circuit; DF: disconnected fan; BL: blocked openings; LF; locked fan; RP: reversed polarity. C.2 TABLE: transformers Loc. Tested insulation Loc. Tested insulation N/A Working voltage peak / V Working voltage rms / V Required electric strength Required clearance / mm Required distance thr. insul. (2.10.3) Required creepage distance / mm (2.10.4) (2.10.2) (2.10.2) (5.2) Test voltage/ V Measured clearance / mm Measured creepage dist./ mm Measured distance thr. insul. / mm; number of layers (2.10.5) supplementary information: C.2 TABLE: transformers Transformer TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 37 of 61 Report No.: RP20170711050 ATTACHMENT TO TEST REPORT IEC 60950-1 EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES Information technology equipment – Safety – PART 1: GENERAL REQUIREMENTS Differences according to..................: EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013 Attachment Form No........................ : EU_GD_IEC60950_1F Attachment Originator......................: SGS Fimko Ltd Master Attachment............................ : Date 2014-02 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013 – CENELEC COMMON MODIFICATIONS IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Contents (A2:2013) General Requirement + Test (A1:2010) General (A2:2013) Verdict Clauses, subclauses, notes, tables and figures which are additional to those in IEC60950-1 and it´s amendmets are prefixed “Z” P Add the following annexes: P Annex ZA (normative) Normative references to international publications with their corresponding European publications Annex ZB (normative) Annex ZD (informative) Special national conditions IEC and CENELEC code designations for flexible cords Delete all the “country” notes in the reference document (IEC 60950-1:2005) according to the following list: 1.4.8 Note 2 1.5.8 Note 2 2.2.3 Note 2.3.2.1 Note 2 2.7.1 Note 3.2.1.1 Note 4.3.6 Note 1 & 2 4.7.3.1Note 2 6 Note 2 & 5 6.2.2 Note 7.1 Note 3 G.2.1 Note 2 General Result - Remark 1.5.1 1.5.9.4 2.2.4 2.3.4 2.10.3.2 3.2.4 4.7 5.1.7.1 6.1.2.1 6.2.2.1 7.2 Annex H Note 2 & 3 Note Note Note 2 Note 2 Note 3. Note 4 Note 3 & 4 Note 2 Note 2 Note Note 2 1.5.7.1 1.7.2.1 2.3.2 2.6.3.3 2.10.5.13 2.5.1 4.7.2.2 5.3.7 6.1.2.2 6.2.2.2 7.3 Note Note 4, 5 & 6 Note Note 2 & 3 Note 3 Note 2 Note Note 1 Note Note Note 1 & 2 Delete all the “country” notes in the reference document (IEC 609501:2005/A1:2010) according to the following list: 1.5.7.1 Note 6.1.2.1 Note 2 6.2.2.1 Note 2 EE.3 Note P Delete all the “country” notes in the reference document (IEC 609501:2005/A2:2013) according to the following list: 2.7.1 Note * 2.10.3.1 Note 2 P P 6.2.2. Note * Note of secretary: Text of Common Modification remains unchanged. 1.3.Z1 Add the following subclause: N/A 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 38 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark Verdict its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones. NOTE Z1 A new method of measurement is described in EN 50332-1, Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations Part 1: General method for “one package equipment”, and in EN 50332-2, Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations Part 2: Guidelines to associate sets with headphones coming from different manufacturers. (A12:2011) N/A In EN 60950-1:2006/A12:2011 Delete the addition of 1.3.Z1 / EN 60950-1:2006 Delete the definition 1.2.3.Z1 / EN 60950-1:2006 /A1:2010 1.5.1 Add the following NOTE: (Added info*) NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see Directive 2002/95/EC. New Directive 2011/65/11 * 1.7.2.1 (A1:2010) 1.7.2.1 (A12.2011) N/A In addition, for a PORTABLE SOUND SYSTEM, the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss. In EN 60950-1:2006/A12:2011 Delete NOTE Z1 and the addition for Portable Sound System. Add the following clause and annex to the existing standard and amendments. N/A Zx Protection against excessive sound pressure from personal music players N/A TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 39 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark Zx.1 General This sub-clause specifies requirements for protection against excessive sound pressure from personal music players that are closely coupled to the ear. It also specifies requirements for earphones and headphones intended for use with personal music players. Verdict N/A A personal music player is a portable equipment for personal use, that: is designed to allow the user to listen to recorded or broadcast sound or video; and primarily uses headphones or earphones that can be worn in or on or around the ears; and allows the user to walk around while in use. NOTE 1 Examples are hand-held or body-worn portable CD players, MP3 audio players, mobile phones with MP3 type features, PDA’s or similar equipment. A personal music player and earphones or headphones intended to be used with personal music players shall comply with the requirements of this sub-clause. The requirements in this sub-clause are valid for music or video mode only. The requirements do not apply: while the personal music player is connected to an external amplifier; or while the headphones or earphones are not used. NOTE 2 An external amplifier is an amplifier which is not part of the personal music player or the listening device, but which is intended to play the music as a standalone music player. The requirements do not apply to: hearing aid equipment and professional equipment; NOTE 3 Professional equipment is equipment sold through special sales channels. All products sold through normal electronics stores are considered not to be professional equipment. analogue personal music players (personal music players without any kind of digital processing of the sound signal) that are brought to the market before the end of 2015. NOTE 4 This exemption has been allowed because this technology is falling out of use and it is expected that within a few years it will no longer exist. This exemption will not be extended to other technologies. For equipment which is clearly designed or intended for use by young children, the limits of EN 71-1 apply. Zx.2 Equipment requirements No safety provision is required for equipment that complies with the following: equipment provided as a package (personal TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 40 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark Verdict music player with its listening device), where the acoustic output LAeq,T is ≤ 85 dBA measured while playing the fixed “programme simulation noise” as described in EN 50332-1; and a personal music player provided with an analogue electrical output socket for a listening device, where the electrical output is ≤ 27 mV measured as described in EN 50332-2, while playing the fixed “programme simulation noise” as described in EN 50332-1. NOTE 1 Wherever the term acoustic output is used in this clause, the 30 s A-weighted equivalent sound pressure level LAeq,T is meant. See also Zx.5 and Annex Zx. All other equipment shall: a) protect the user from unintentional acoustic outputs exceeding those mentioned above; and b) have a standard acoustic output level not exceeding those mentioned above, and automatically return to an output level not exceeding those mentioned above when the power is switched off; and c) provide a means to actively inform the user of the increased sound pressure when the equipment is operated with an acoustic output exceeding those mentioned above. Any means used shall be acknowledged by the user before activating a mode of operation which allows for an acoustic output exceeding those mentioned above. The acknowledgement does not need to be repeated more than once every 20 h of cumulative listening time; and NOTE 2 Examples of means include visual or audible signals. Action from the user is always required. NOTE 3 The 20 h listening time is the accumulative listening time, independent how often and how long the personal music player has been switched off. d) have a warning as specified in Zx.3; and e) not exceed the following: 1) equipment provided as a package (player with Its listening device), the acoustic output shall be ≤ 100 dBA measured while playing the fixed “programme simulation noise” described in EN 50332-1; and 2) a personal music player provided with an analogue electrical output socket for a listening device, the electrical output shall be ≤ 150 mV measured as described in EN 50332-2, while playing the fixed “programme simulation noise” described in EN 50332-1. For music where the average sound pressure (long term LAeq,T) measured over the duration of the song is lower than the average produced by the programme simulation noise, the warning does not TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 41 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark Verdict need to be given as long as the average sound pressure of the song is below the basic limit of 85 dBA. In this case T becomes the duration of the song. NOTE 4 Classical music typically has an average sound pressure (long term LAeq,T) which is much lower than the average programme simulation noise. Therefore, if the player is capable to analyse the song and compare it with the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dBA. For example, if the player is set with the programme simulation noise to 85 dBA, but the average music level of the song is only 65 dBA, there is no need to give a warning or ask an acknowledgement as long as the average sound level of the song is not above the basic limit of 85 dBA. Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: the symbol of Figure 1 with a minimum height of 5 mm; and the following wording, or similar: N/A “To prevent possible hearing damage, do not listen at high volume levels for long periods.” Figure 1 – Warning label (IEC 60417-6044) Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. Zx.4 Requirements for listening devices (headphones and earphones) Zx.4.1 Wired listening devices with analogue input With 94 dBA sound pressure output LAeq,T, the input voltage of the fixed “programme simulation noise” described in EN 50332-2 shall be ≥ 75 mV. N/A N/A This requirement is applicable in any mode where the headphones can operate (active or passive), including any available setting (for example built-in volume level control). NOTE The values of 94 dBA – 75 mV correspond with 85dBA – 27 mV and 100 dBA – 150 mV. Zx.4.2 Wired listening devices with digital input With any playing device playing the fixed “programme simulation noise” described in EN TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 42 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark Verdict 50332-1 (and respecting the digital interface standards, where a digital interface standard exists that specifies the equivalent acoustic level), the acoustic output LAeq,T of the listening device shall be ≤ 100 dBA. This requirement is applicable in any mode where the headphones can operate, including any available setting (for example built-in volume level control, additional sound feature like equalization, etc.). NOTE An example of a wired listening device with digital input is a USB headphone. Zx.4.3 Wireless listening devices In wireless mode: with any playing and transmitting device playing the fixed programme simulation noise described in EN 50332-1; and respecting the wireless transmission standards, where an air interface standard exists that specifies the equivalent acoustic level; and with volume and sound settings in the listening device (for example built-in volume level control, additional sound feature like equalization, etc.) set to the combination of positions that maximize the measured acoustic output for the abovementioned programme simulation noise, the acoustic output LAeq,T of the listening device shall be ≤ 100 dBA. N/A NOTE An example of a wireless listening device is a Bluetooth headphone. Zx.5 Measurement methods Measurements shall be made in accordance with EN 50332-1 or EN 50332-2 as applicable. Unless stated otherwise, the time interval T shall be 30 s. N/A NOTE Test method for wireless equipment provided without listening device should be defined. TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 43 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test 2.7.1 Replace the subclause as follows: Result - Remark Verdict N/A Basic requirements To protect against excessive current, short-circuits and earth faults in PRIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault protection may be provided by protective devices in the building installation; 2.7.2 c) it is permitted for PLUGGABLE EQUIPMENT TYPE B or PERMANENTLY CONNECTED EQUIPMENT, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for PLUGGABLE EQUIPMENT TYPE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet. This subclause has been declared ‘void’. N/A 3.2.3 Delete the NOTE in Table 3A, and delete also in this table the conduit sizes in parentheses. N/A 3.2.5.1 Replace N/A “60245 IEC 53” by “H05 RR-F”; “60227 IEC 52” by “H03 VV-F or H03 VVH2-F”; “60227 IEC 53” by “H05 VV-F or H05 VVH2-F2”. In Table 3B, replace the first four lines by the following: Up to and including 6 | Over 6 up to and including 10| (0,75) b) Over 10 up to and including 16| (1,0) c) 0,75 a) | 1,0 | 1,5 | In the conditions applicable to Table 3B delete the words “in some countries” in condition a). In NOTE 1, applicable to Table 3B, delete the second sentence. 3.2.5.1 (A2:2013) NOTE Z1 The harmonised code designations corresponding to the IEC cord types are given in Annex ZD TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 44 of 61 Report No.: RP20170711050 IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark 3.3.4 In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Verdict N/A Over 10 up to and including 16 | 1,5 to 2,5 | 1,5 to 4 | Delete the fifth line: conductor sizes for 13 to 16 A 4.3.13.6 (A1:2010) N/A Replace the existing NOTE by the following: NOTE Z1 Attention is drawn to: 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz, and 2006/25/EC: Directive on the minimum health and safety requirements regarding the exposure of workers to risks arising from physical agents (artifical optical radiation). Annex H Standards taking into account mentioned Recommendation and Directive which demonstrate compliance with the applicable EU Directive are indicated in the OJEC. N/A Replace the last paragraph of this annex by: N/A At any point 10 cm from the surface of the OPERATOR ACCESS AREA, the dose rate shall not exceed 1 μSv/h (0,1 mR/h) (see NOTE). Account is taken of the background level. Replace the notes as follows: NOTE These values appear in Directive 96/29/Euratom. Delete NOTE 2. Bibliography Additional EN standards. ZA NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR CORRESPONDING EUROPEAN PUBLICATIONS ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause 1.2.4.1 1.2.13.14 (A11:2009) 1.5.7.1 (A11:2009) Requirement + Test In Denmark, certain types of Class I appliances (see 3.2.1.1) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets. In Norway and Sweden, for requirements see 1.7.2.1 and 7.3 of this annex. In Finland, Norway and Sweden, resistors bridging BASIC INSULATION in CLASS I PLUGGABLE EQUIPMENT TYPE A must comply with the requirements in 1.5.7.1. In addition when a single resistor is used, the resistor must withstand the resistor test in 1.5.7.2. TRF No.: IEC60950_1F Result - Remark Verdict N/A N/A N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 45 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test 1.5.8 In Norway, due to the IT power system used (see annex V, Figure V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V). In Finland, Norway and Sweden, the third dashed sentence is applicable only to equipment as defined in 6.1.2.2 of this annex. In Finland, Norway and Sweden, CLASS I PLUGGABLE EQUIPMENT TYPE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. 1.5.9.4 1.7.2.1 Result - Remark Verdict N/A N/A N/A The marking text in the applicable countries shall be as follows: In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In Norway: “Apparatet må tilkoples jordet stikkontakt” In Sweden: “Apparaten skall anslutas till jordat uttag” 1.7.2.1 (A11:2009) In Norway and Sweden, the screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building. Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system. It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator, which may be provided by e.g. a retailer. The user manual shall then have the following or similar information in Norwegian and Swedish language respectively, depending on in what country the equipment is intended to be used in: “Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing – and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11).” TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 46 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test Result - Remark Verdict NOTE In Norway, due to regulation for installations of cable distribution systems, and in Sweden, a galvanic isolator shall provide electrical insulation below 5 MHz. The insulation shall withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60 Hz, for 1 min. 1.7.2.1 (A2:2013) Translation to Norwegian (the Swedish text will also be accepted in Norway): “Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr – og er tilkoplet et kabel-TV nett, kan forårsake brannfare. For å unngå dette skal det ved tilkopling av utstyret til kabel-TV nettet installeres en galvanisk isolator mellom utstyret og kabel- TV nettet.” Translation to Swedish: ”Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt är kopplad till kabel-TV nät kan i vissa fall medfőra risk főr brand. Főr att undvika detta skall vid anslutning av utrustningen till kabel-TV nät galvanisk isolator finnas mellan utrustningen och kabel-TV nätet.” In Denmark, CLASS I PLUGGABLE EQUIPMENT TYPE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. N/A The marking text in Denmark shall be as follows: In Denmark: “Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.” 1.7.5 1.7.5 (A11:2009) In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section 107-2-D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIONARY EQUIPMENT the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a. For CLASS II EQUIPMENT the socket outlet shall be in accordance with Standard Sheet DKA 1-4a. TRF No.: IEC60950_1F N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 47 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test 1.7.5 In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the DS 60884-2-D1:2011. For class I equipment the following Standard Sheets are applicable: DK 1-3a, DK 1-1c, DK 1-1d, DK 1-5a or DK 1-7a, with the exception for STATIONARY EQUIPMENT where the socketoutlets shall be in accordance with Standard Sheet DK 1-1b, DK 1-1c, DK 1- 1d or DK 1-5a. Socket outlets intended for providing power to Class II apparatus with a rated current of 2,5 A shall be in accordance with DS 60884-2-D1 standard sheet DKA 1-4a. Other current rating socket outlets shall be in compliance with by DS 60884-2-D1 Standard Sheet DKA 1-3a or DKA 1-3b. Justification the Heavy Current Regulations, 6c In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex. In Finland, Norway and Sweden there are additional requirements for the insulation. See 6.1.2.1 and 6.1.2.2 of this annex. In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex. In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not 16 A. In the United Kingdom, to protect against excessive currents and short-circuits in the PRIMARY CIRCUIT of DIRECT PLUG-IN EQUIPMENT, tests according to 5.3 shall be conducted, using an external protective device rated 30 A or 32 A. If these tests fail, suitable protective devices shall be included as integral parts of the DIRECT PLUG-IN EQUIPMENT, so that the requirements of 5.3 are met. In Finland, Norway and Sweden, there are additional requirements for the insulation, see 6.1.2.1 and 6.1.2.2 of this annex. (A2:2013) 2.2.4 2.3.2 2.3.4 2.6.3.3 2.7.1 2.10.5.13 TRF No.: IEC60950_1F Result - Remark Verdict N/A N/A N/A N/A N/A N/A N/A Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 48 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test 3.2.1.1 Result - Remark In Switzerland, supply cords of equipment having a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC 60884-1 and one of the following dimension sheets: SEV 6532-2.1991 Plug Type 15 250/400 V, 10 A 3P+N+PE SEV 6533-2.1991 Plug Type 11 250 V, 10 A SEV 6534-2.1991 Plug Type 12 250 V, 10 A L+N Verdict N/A L+N+PE In general, EN 60309 applies for plugs for currents exceeding 10 A. However, a 16 A plug and socketoutlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV 5932-2.1998: Plug Type 25 , 3L+N+PE 230/400 V, 16 A SEV 5933-2.1998:Plug Type 21, L+N, 250 V, 16A SEV 5934-2.1998: Plug Type 23, L+N+PE V, 16 A 3.2.1.1 250 In Denmark, supply cords of single-phase equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations, Section 107-2-D1. N/A CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If poly-phase equipment and single-phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section 107-2-D1 or EN 60309-2. TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 49 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test 3.2.1.1 In Denmark, supply cords of single-phase equipment having a rated current not exceeding 13 A shall be provided with a plug according to DS 60884-2-D1. CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If a single-phase equipment having a RATED CURRENT exceeding 13 A or if a poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with the standard sheets DK 6-1a in DS 60884-2-D1 or EN 60309-2. Justification the Heavy Current Regulations, 6c N/A 3.2.1.1 In Spain, supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315:1994. N/A (A2:2013) Result - Remark Verdict Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UNE-EN 50075:1993. CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UNE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UNE-EN 60309-2. 3.2.1.1 In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a ‘standard plug’ in accordance with Statutory Instrument 1768:1994 The Plugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. N/A NOTE ‘Standard plug’ is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 50 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test 3.2.1.1 Result - Remark Verdict In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525:1997 - National Standards Authority of Ireland (section 28) (13 A Plugs and Conversion Adaptors for Domestic Use) Regulations 1997. N/A 3.2.4 In Switzerland, for requirements see 3.2.1.1 of this annex. N/A 3.2.5.1 In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A. N/A 3.3.4 In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRENT of over 10 A up to and including 13 A is: N/A • 1,25 mm2 to 1,5 mm2 nominal cross-sectional area. 4.3.6 In the United Kingdom, the torque test is performed using a socket outlet complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003 and the plug part of DIRECT PLUG-IN EQUIPMENT shall be assessed to BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, 12.16 and 12.17, except that the test of 12.17 is performed at not less than 125 °C. Where the metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the requirements of clauses 22.2 and 23 also apply. N/A 4.3.6 In Ireland, DIRECT PLUG-IN EQUIPMENT is known as plug similar devices. Such devices shall comply with Statutory Instrument 526:1997 National Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, 1997. N/A TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 51 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test 5.1.7.1 Result - Remark In Finland, Norway and Sweden TOUCH CURRENT measurement results exceeding 3,5 mA r.m.s. are permitted only for the following equipment: Verdict N/A • STATIONARY PLUGGABLE EQUIPMENT TYPE A that is intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, for example, in a telecommunication centre; and has provision for a permanently connected PROTECTIVE EARTHING CONDUCTOR; and is provided with instructions for the installation of that conductor by a SERVICE PERSON; • STATIONARY PLUGGABLE EQUIPMENT TYPE B; • STATIONARY PERMANENTLY CONNECTED EQUIPMENT. 6.1.2.1 (A1:2010) In Finland, Norway and Sweden, add the following text between the first and second paragraph of the compliance clause: N/A If this insulation is solid, including insulation forming part of a component, it shall at least consist of either two layers of thin sheet material, each of which shall pass the electric strength test below, or one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirements for the insulation consisting of an insulating compound completely filling the casing, so that CLEARANCES and CREEPAGE DISTANCES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition passes the tests and inspection criteria of 2.10.11 with an electric strength test of 1,5 kV multiplied by 1,6 (the electric strength test of 2.10.10 shall be performed using 1,5 kV), and is subject to ROUTINE TESTING for electric strength during manufacturing, using a test voltage of 1,5 kV. TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 52 of 61 Report No.: RP20170711050 ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test Result - Remark Verdict It is permitted to bridge this insulation with an optocoupler complying with 2.10.5.4 b). It is permitted to bridge this insulation with a capacitor complying with EN 60384-14:2005, subclass Y2. A capacitor classified Y3 according to EN 60384-14:2005, may bridge this insulation under the following conditions: the insulation requirements are satisfied by having a capacitor classified Y3 as defined by EN 60384-14, which in addition to the Y3 testing, is tested with an impulse test of 2,5 kV defined in EN 60950-1:2006, 6.2.2.1; the additional testing shall be performed on all the test specimens as described in EN 60384-14: the impulse test of 2,5 kV is to be performed before the endurance test in EN 60384-14, in the sequence of tests as described in EN 6038414. 6.1.2.2 In Finland, Norway and Sweden, the exclusions are applicable for PERMANENTLY CONNECTED EQUIPMENT, PLUGGABLE EQUIPMENT TYPE B and equipment intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected PROTECTIVE EARTHING CONDUCTOR and is provided with instructions for the installation of that conductor by a SERVICE PERSON. N/A 7.2 In Finland, Norway and Sweden, for requirements see 6.1.2.1 and 6.1.2.2 of this annex. N/A The term TELECOMMUNICATION NETWORK in 6.1.2 being replaced by the term CABLE DISTRIBUTION SYSTEM. 7.3 In Norway and Sweden, for requirements see 1.2.13.14 and 1.7.2.1 of this annex. N/A 7.3 In Norway, for installation conditions see EN 60728-11:2005. N/A (A11:2009) (A11:2009) TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 53 of 61 Report No.: RP20170711050 Annex ZD (informative) IEC and CENELEC code designations for flexible cords Type of flexible cord Code designations IEC CENELEC PVC insulated cords Flat twin tinsel cord 60227 IEC 41 H03VH-Y Light polyvinyl chloride sheathed flexible cord 60227 IEC 52 H03VV-F H03VVH2-F Ordinary polyvinyl chloride sheathed flexible cord 60277 IEC 53 H05VV-F H05VVH2-F Rubber insulated cords Braided cord 60245 IEC 51 H03RT-F Ordinary tough rubber sheathed flexible cord 60245 IEC 53 H05RR-F Ordinary polychloroprene sheathed flexible cord 60245 IEC 57 H05RN-F Heavy polychloroprene sheathed flexible cord 60245 IEC 66 H07RN-F Cords having high flexibility Rubber insulated and sheathed cord 60245 IEC 86 H03RR-H Rubber insulated, crosslinked PVC sheathed cord 60245 IEC 87 H03RV4-H Crosslinked PVC insulated and sheathed cord 60245 IEC 88 H03V4V4-H TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 54 of 61 Report No. : RP20170711050 EUT Photo The overall view of EUT The rear view of EUT TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 55 of 61 Report No. : RP20170711050 The inside view of EUT The top view of KEY PCB TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 56 of 61 Report No. : RP20170711050 The rear view of KEY PCB The top view of VIP PCB TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 57 of 61 Report No. : RP20170711050 The rear view of VIP PCB The top view of LCD TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 58 of 61 Report No. : RP20170711050 The rear view of LCD All the view of loudspeaker TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 59 of 61 Report No. : RP20170711050 The inside view of handset Adapter TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 60 of 61 Report No. : RP20170711050 Adapter TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd. Page 61 of 61 Report No. : RP20170711050 TEST INSTRUMENTS REFERENCE LIST Instr. Instrument Instrument Range Used Code I.D. Type Or *** Input: 200/240Vac,4763Hz, 5000VA. Output:0-60V,0-46A, 2760W. Maker and Model ** Calibration Date Last Due 2016/12/05 2017/12/05 SE02 A00017328 DC Power Supply SE17 A00017339 Test Finger Dimensions please refer ED.D / UFP-01 to GB4943 Fig.2A 2016/11/07 2017/11/07 SE20 SE20 Test Pin Dimensions please refer GZ-ZLT / SYX-1 to GB4943 Fig.2B 2016/12/09 2017/12/09 SE36 AG001 Electronic Stop Watch Min:0.01s TF / PC396 2017/04/19 2018/04/19 A10054895 AC:5KV,40mA max. Electrical Safety DC:6KV, 12mA max. Analyzer GB:30A, 0.21ohm max(0~360s) Chroma / 19032 2016/11/14 2017/11/14 A22760117 Four Channels, Bandwidth:500M max Input Range:: 400Vpeak(or CAT I150Vrms/CAT II Digital Phosphor 100Vrms, BNC Oscilloscope Input(1MΩ)), 5Vrms and Vpeak≤±30V(BNC Input(50Ω)) Input Impedance:1MΩ,50Ω Tektronix / TDS3034C 2016/11/04 2017/11/04 K type:-267℃ -260℃ Agilent / 34901A 2017/04/05 2018/04/05 Digiton Force Gauge Max.Scale: 1000N AIGU / ZP-1000 2016/08/03 2017/08/03 Dropping wood Hardwood thick：13mm Each of two plywood ETR / SE102 thick：19mm～20mm N/A N/A SE42 SE83 SE85-01 20-Channel 1-A22804814 Armature Multiplexer SE93-01 SE93-01 SE102 SE102 Chroma / 6202F-60 --- End of Report --- TRF No.: IEC60950_1F Shenzhen Zoom Rel Testing Technology Co., Ltd.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Page Count : 61 Author : JMW Comments : Company : Create Date : 2017:07:21 17:20:37+09:20 Creator : WPS Office Keywords : TRF, -, CB, Scheme Modify Date : 2017:07:21 17:20:37+09:20 Producer : Source Modified : D:20170721172037+09'20' Subject : IEC/EN Title : TEST REPORT FORM TEMPLATE Trapped : falseEXIF Metadata provided by EXIF.tools