Xplore Technologies MC7700 MC7700 Modem User Manual ix104c5 handbook

Xplore Technologies MC7700 Modem ix104c5 handbook

Users Manual

USER’S HANDBOOK
iX104C5 User’s Handbook  3ContentsWelcome  13About your computer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15Contacting Xplore – service and questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  171Getting Started  19Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19Back view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20Left side view  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21Right side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  22Bottom view  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23Top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23LED indicators  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24Quick-start guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Application, Windows, and hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  262Using the Tablet  29Turning on the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29Turning off the computer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30Using the Reset switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30Suspending and resuming operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31Suspending operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32Resuming operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
Contents4 iX104C5 User’s HandbookUsing the pen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34Using the digitizer to perform mouse functions. . . . . . . . . . . . . . . . . . . . . . .  35Changing the pen double-click speed . . . . . . . . . . . . . . . . . . . . . . . . . . .  35Positioning the pen and pen tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36Using the fingerprint scanner  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38Changing the screen orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39Adjusting the screen brightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  40Enabling automatic backlight control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41Optimizing screen settings for outdoor use . . . . . . . . . . . . . . . . . . . . . . . . . .  41Docking the tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  42Connecting devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43Connecting to a local area network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43Connecting USB-compatible devices  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43Connecting an external microphone  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Adjusting microphone volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Connecting a headphone or speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45Adjusting headphone or speaker volume . . . . . . . . . . . . . . . . . . . . . . . .  45Connecting a monitor or projection panel (optional). . . . . . . . . . . . . . . . . . .  46Activating the monitor or projection panel. . . . . . . . . . . . . . . . . . . . . . .  46Connecting a device to the serial port (standard). . . . . . . . . . . . . . . . . . . . . .  47Connecting an XPL expansion module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47Using the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48Charging the battery pack  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48If you do not have an external battery charger . . . . . . . . . . . . . . . . . . . .  48If you have an external battery charger  . . . . . . . . . . . . . . . . . . . . . . . . .  49Removing and installing the battery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49Removing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49Installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51Discarding batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51
ContentsiX104C5  User’s Handbook  5Using power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52Displaying power options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52Checking battery power status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52Selecting a power plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Selecting power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54Selecting Power (On/Off)/Backlight(On/Off)/Sleep/ Resume button options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55Tips for conserving battery power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56Accessing the Solid State Drive (SSD) cartridge . . . . . . . . . . . . . . . . . . . . . . . . .  57Re-installing the drive carrier  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58Accessing the MicroSD and SIM compartment . . . . . . . . . . . . . . . . . . . . . . . . . .  59Programming hot keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  60Programming hot keys to start applications, open documents, or go to a website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61Programming hot keys to perform pre-defined functions . . . . . . . . . . . . . . .  65Programming hot keys to perform other key functions . . . . . . . . . . . . . . . . .  673Maintaining the Tablet  71Caring for the tablet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71Checking power cords and connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71Protecting the computer from damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71Preventing the computer from overheating . . . . . . . . . . . . . . . . . . . . . . . . . .  72Storing the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73Caring for the display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73Protecting the display screen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73When to replace the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74Calibrating the digitizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75
Contents6 iX104C5 User’s HandbookATroubleshooting 77BUsing BIOS and AOS Functions 79Disabling the Auto Power feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80Enabling automatic LCD backlight control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80CGlossary 81DHardware Specifications 87EAgency Notices 93FEnvironmental Policy and Recycling Program 105Environmental policy  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  105Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  105Risk reduction, prevention, and resource management  . . . . . . . . . . . .  105Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  106Continuous improvement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  106Take back and recycling program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  106Environmental and Sustainability Corporate Report  . . . . . . . . . . . . . . . . . . . . .  107
iX104C5 User’s Handbook  7DisclaimerXplore Technologies® has made every effort to ensure the accuracy and completeness of this document; however, because ongoing development efforts are made to continually improve the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes herein.TrademarksXplore and the Xplore logo are registered trademarks of Xplore Technologies Corp.; iX104, iX104C5, iX104C5 Lite, and iX104C5 Dual Mode are trademarks of Xplore Technologies Corp. Kensington and MicroSaver are registered trademarks of the Kensington Technology Group. Microsoft is a registered trademark of Microsoft Corporation. Windows 7, Windows XP Professional, and Windows XP Tablet PC Edition are trademarks of Microsoft Corporation. MicroSD is registered trademark of the Personal Computer Memory Card International Association. Intel and iCore, are registered trademarks of Intel Corporation. Wi-Fi is a trademark of the Wireless Ethernet Compatibility Alliance (WECA). ISODAMP is a registered trademark of Aearo Company. All other brands, product names, company names, trademarks and service marks used herein are property of their respective companies. CopyrightCopyright © 2003-2013 Xplore Technologies Corp. All rights reserved. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Xplore Technologies. No part of this publication may be stored or transmitted in any electronic form without the prior consent of Xplore Technologies. Any unauthorized use is a violation of copyright laws.Publication informationPN: 95-01097, Rev. BApril 2013
8 iX104C5 User’s HandbookDeclaration of conformityDECLARATION OF CONFORMITY according to FCC Part 15, IC ICES-003, and RTT&E directivesResponsible Party Name: Xplore TechnologiesAddress: 14000 Summit Drive, Suite 900, Austin, Texas 78728Telephone: 512.336.7797Declares that product: Model Series: iX104C5 complies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and, (2) This device must accept any interference received, including interference that may cause undesired operation.WARNINGChanges or modifications to this unit not expressly approved by the party responsible for compliance may void the user’s authority to operate this equipment. For more information about FCC rules and their applicability to the iX104, see Appendix E, “Agency Notices.” Energy Star PartnerWarranty informationThe iX104C5 is backed by a standard 36-month International Limited Warranty. An extended International Limited Warranty is available. Check the service kit included with your computer for warranty terms and conditions.
iX104C5 User’s Handbook  9Important safety informationBefore you use the iX104C5 (referred to as the tablet), read these safety instructions and the operation instructions in this handbook.Failure to observe all these instructions voids the Limited Warranty and may lead to suspension or denial of services to the offender, or legal action, or both.Follow any special regulations governing the use of the tablet and, if radio-enabled, always switch it off in areas where radio devices are forbidden or when the radio device can cause interference or danger.Always follow any safety laws and regulations pertaining to the use of cell phones and two-way radios, because these laws and regulations typically apply to the use of the wireless-enabled tablet.Observe all restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas), chemical plants, and wherever blasting operations are in progress or in any area in which restrictions on radio transmissions are imposed.Switch off the tablet when in an aircraft. The tablet is not FAA-approved for use on aircraft. The effect of the use of the tablet in aircraft is unknown. Using the tablet in an aircraft may affect aircraft instrumentation, communication, and performance; may disrupt the network; and may be illegal.Operating the wireless-enabled tablet may interfere with the functioning of inadequately protected medical devices such as pacemakers. Consult a physician or the manufacturer of the medical device if you have any questions. Radio signals from your tablet will not affect the operation of most modern equipment, but certain electronic equipment, including automotive systems, may not be shielded against radio signals from your tablet. Check with the manufacturer of your motor vehicle or the manufacturer’s representative to determine whether using the tablet will present any safety issues.Avoid using the tablet in any environment that requires your full attention, such as when driving a vehicle. If you need to use your tablet while driving, have a passenger use it for you or find a safe location to halt your vehicle.WARNING – BATTERIESUse only battery types specified in this handbook. Using any other type of battery can be dangerous and can disable the tablet. Do not drop or mishandle the batteries, immerse them in water, or subject them to high heat. Doing so could increase the risk of explosion or leakage, and possibly cause injury. The lithium-ion batteries used in this equipment contain material that is hazardous to your health. If battery contents come in contact with the eyes, IMMEDIATELY flush the affected area with clean water for 15 minutes and have someone else summon medical attention for you. Unaffected persons should assist the affected individual in the vital first flushing of the eyes. RECHARGING THE BATTERY MUST ONLY BE CARRIED OUT IN ANON-HAZERDOUS AREA USING THE SUPPLIED AC ADAPTOR. The definition of hazardous areas can be found in Standard EN 60079-10.
10  iX104C5 User’s HandbookWARNINGWhen operating the tablet in a known explosive environment do not remove or replace the battery while the circuit is live. Before removing the battery verify that the area is known to be free of ignitable concentrations of flammable substances. EXPLOSION HAZARD – DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON-HAZARDOUS.AVERISSEMENT – RISQUE D’EXPLOSION. NE PAS DÉBRANCHER TANT QUE LE CIRCUIT EST SOUS TENSION, À MOINS QU’IL NE S’AGISSE D’UN EMPLACEMENT NON DANGEREUX.WARNINGEXPLOSION HAZARD – DO NOT REPLACE THE BATTERY UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.AVERTISSEMENT – RISQUE D'EXPLOSION – COUPER LE COURANT OU S'ASSURER QUEL'EMPLACEMENT EST DESIGNE NON DANGEREUX AVANT DE REPLACER LE BATTERY.WARNINGEXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIViSION 2.AVERTISSEMENT – RISQUE D'EXPLOSION – LA SUBSTITUTIOND E COMPOSANTSP EUTR ENDRE CE MATERIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 2.WARNINGEXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.AVERTISSEMENT – RISQUE D'EXPLOSION – AVANT DE DECONNECTER L'EQUIPEMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX.WARNINGDo not use any dock or any other accessory or attachment that is not manufactured or supplied by Xplore or an authorized Xplore accessories supplier. Use of any accessory or attachment that is not supplied or approved for use with the tablet by Xplore is not permitted because it may cause hazards.Operate the tablet only from the type of power source indicated on the marking label. (See page 48 for more information about the battery and power supply.) Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs and convenience receptacles, and at the point where cords exit from the tablet or its dock. Do not overload wall outlets, extension cords, or integral convenience receptacles because this can cause fire or electric shock.
iX104C5 User’s Handbook  11Unplug the tablet and refer the tablet and dock for service to qualified service personnel if any of the following conditions occur:■The power supply cord or plug is damaged.■The tablet or dock does not operate normally when you follow the instructions in this book.■The tablet or dock exhibits a distinct change in performance.Adjust only controls for which there are instructions in this book. An improper adjustment of other controls can result in damage and may require extensive work by a qualified technician to restore the tablet or dock to normal operation.CAUTIONAvoid prolonged physical contact with the exposed metal surfaces on the front and back of the tablet. While the tablet may not feel hot to the touch, if you maintain physical contact with the tablet for a long time (for example, if you rest the tablet on your lap for a long time), your skin may suffer low-heat injury. In addition, be careful when you remove a PC card that has been used for a long time, because the card may be hot.
12  iX104C5 User’s Handbook
iX104C5 User’s Handbook  13WelcomeWelcome to the Xplore Technologies® iX104C5™tablet PC, the rugged tablet designed, tested, and manufactured to meet the environmental and physical real-world challenges faced by today’s mobile workers. Based on years of experience in rugged mobile applications, the iX104C5 is designed to withstand the abuses of everyday wear and tear.Advanced technology, innovative design, and a rugged case are just a few highlights of your iX104C5 system. Note: This handbook assumes that you have basic experience using computers and Microsoft® Windows®.Tablet with enhanced performance antenna
Welcome14  iX104C5 User’s HandbookAbout your computerThe iX104C5 is a high-performance tablet PC that runs on Microsoft Windows 7 32-bit and 64-bit operating systems. You can use any of the following methods to control the tablet:■Special, enhanced pen (included with the tablet)■Your finger■Any suitable pointing deviceNote: In this handbook, all information applies to all models unless otherwise noted.All iX104C5 tablets have been engineered and tested to meet Military Standards for Environmental Extremes (MIL STD 810G). Your tablet includes the following features that make it exceptionally rugged and durable:■Durable, long-lasting, rigid magnesium enclosure ■Interior and exterior multi-layer magnesium structure ■Bumper system and gasket protection mechanisms ■Specialized drive technology ■Removable, dual, Solid State Drive (SSD) cartridge ■Integrated, protected wireless LAN and WAN antennas for dual mode operation ■Locked-in-place memory, cables, and connectors ■Proprietary thermal management system
WelcomeiX104C5 User’s Handbook  15Package contentsCheck to make sure your package includes the following items:■Quick Start Guide■Battery pack■Power cord■AC adapter■Pen (attached to tablet)■Pen tether (attached to tablet)■iX104C5 tablet PC■Warranty information kit■Operating System Recovery GuideOptional accessoriesYour package also includes any optional accessories you ordered.Docking options■xStand Desktop Docking Station■xDock Vehicle Docking StationCarrying cases■Shoulder cases■Portfolio case■Dockable caseMemory■2, 4, or 8 GB RAM■40, 80, or more GB Solid State Drive (SSD)
Welcome16  iX104C5 User’s HandbookPower options■AC adapter with U.S. cord■Weight-reduced battery pack (56 watt hours)■Extended life battery pack (68.5 watt hours)■Auto adapter (cigarette lighter adapter)Additional accessories■Top-mounted Fast-Lock GPS II Pro (submeter accuracy)■Non-rugged USB optical disk drive ■USB rugged, backlit keyboard (83-key) ■Replaceable drive cartridges ■Active stylus
WelcomeiX104C5 User’s Handbook  17Contacting Xplore – service and questionsNote: To troubleshoot problems (including wireless and GPS problems), before you call, read the FAQ page of the Xplore Technologies Web site. Go to http://www.xploretech.com; then select Customer Support; then FAQ.If you purchased your tablet from an authorized Xplore dealer, contact the dealer for service and support.If you purchased your tablet directly from Xplore, use any of the following methods to contact Xplore for service and support:Before you contact Xplore, have the following information ready so that the customer support representative can quickly provide a solution:Web site http://www.xploretech.comE-mail customersupport@xploretech.comToll free 1-866-296-8541, extension 222Fax 1-512-336-7791Product name: iX104C5Product serial numberPurchase dateConditions under which the problem occurredAny error messages that were displayedType of device connected, if any
18  iX104C5 User’s Handbook
iX104C5 User’s Handbook  191Getting StartedThis chapter gives you an overview of your tablet and includes a quick-start guide to tablet keys.Front viewBuilt-inmicrophoneSpeaker SpeakerAuto Light sensorReset switchStatus indicatorSSD indicator Fingerprint scannerBuilt-in microphone Enables you to input mono audio with noise cancellation. (See page 44.)Reset switch Enables you to turn off the computer when using the Power (On/Off)/Backlight (On/Off)/Resume key is not effective. (See page 30.)Status indicator Indicates the computer status (on, off, etc.). (See page 24.)Speakers Enable you to listen to stereo audio files. Sealed to provide protection from the environment.
Chapter 1. Getting StartedBack view20  iX104C5 User’s HandbookBack viewAuto Light sensor Detects ambient light conditions.SSD indicator Indicates hard drive activity. (See page 24.)Fingerprint scanner Enables you to use fingerprint verification features. (See page 38.)Fan coverPenRemovablebattery packBatteryreleaselatchPen holderAntennacoversDigital cameraBatterylockbuttonSSD carrierFan cover Plastic cover over the thermal transfer bay that manages heat movement out of the computer.Antenna covers For optional wireless LAN and WAN models, protect and secure the radio antennas (accessible by authorized service personnel only).Pen The main device you use to enter data and control applications (instead of a mouse or a keyboard). Also called the stylus. See “Using the pen” on page 34.
Chapter 1. Getting StartedLeft side viewiX104C5 User’s Handbook  21Left side viewPen holder  Provides a place to secure the pen when you are not using it.Battery release latch Provides access to the battery.Battery lock button Secures the battery inside the tablet.Removable battery pack Powers the computer when AC power is unavailable.Digital camera 3-mega-pixel, auto-focus camera for taking color or black-and-white image or video.SSD carrier User-accessible drive carrier for SSD storage.Power On/Off, Backlight On/Off, Sleep/Resume buttonHeat exchange XPL side portKensingtonlock slotPower On/Off, Backlight On/Off, Sleep/Resume buttonPress to power computer. Press and hold for more than 4 seconds to force power off. Momentarily press to toggle the backlight on or off.Heat exchange Helps prevent the computer from overheating by forcing heat away from the computer. (Do not block the vents.)XPL side port Permits connection of special devices made expressly for the iX104C5.Kensington™ lock slot Connector for the optional Kensington MicroSaver™ or equivalent compatible security cable.Note: Contact your reseller for information about the Kensington security cable.
Chapter 1. Getting StartedRight side view22  iX104C5 User’s HandbookRight side viewThe connectors on the right side of the computer are located behind the outer doors.MicrophoneconnectorPowerconnector 9-pin serial connector or optional connector for external monitorLAN connectorUSB portsHeadphoneconnectorPower connector For the AC adapter or optional auto adapter. (See “Optional accessories” on page 15.)USB 2.0 ports For Universal Serial Bus devices (compliant with USB Standard Revision 2.0). Note: The optional Office and Vehicle Docks include additional USB ports. See “Optional accessories” on page 15.Headphone connector For stereo headphones or speakers.Microphone connector For an external microphone.LAN connector For connecting a standard RJ-45 connector to the tablet’s internal local area network (LAN) card9-pin serial connectoror optional external monitor connectorSerial connector for connecting terminals or other devices that use the RS-232, RS-422, or RS-485 data transfer standard, or an optional connector for an external monitor or projection panel.
Chapter 1. Getting StartedBottom viewiX104C5 User’s Handbook  23Bottom viewTop viewDocking connector for the optional Xplore Tablet DockGuide pin receptaclesDocking connector Enables you to connect the optional xStand Desktop Docking Station or xDock Vehicle Docking Stations. Guide pin receptacles Help assure a secure connection of the optional xStand or xDock. Note: See “Optional accessories” on page 15.XPL expansion portBumpersBumpers Fabricated from rugged material. Raised to help protect the computer from damage.XPL expansion port A port that permits connection of special devices made expressly for the iX104C5.
Chapter 1. Getting StartedLED indicators24  iX104C5 User’s HandbookLED indicatorsThe LED indicator lights show the status of system functions.The following table defines the various LED states.Status LEDDrive LEDTable 1 Status LED indicatorMode/State LED State MeaningOn state green, continuous The computer is on, ready for use, and functioning normally. The battery is fully charged.Charging green, blinking The AC adapter is plugged in and the battery is charging.Off state off (no light) The computer is off.Sleep mode green, breathing The computer is on and is in Sleep mode.Thermal control blue, blinking The computer is on and is in Warm-up mode, with the LCD and backlight off. After the system has warmed to a safe level, the LCD and backlight turn on.
Chapter 1. Getting StartedLED indicatorsiX104C5 User’s Handbook  25On red, blinking The computer is powered on, running on battery power, and the charge level in the battery has reached a minimum warning state. Plug the computer into an AC/DC power source or install a charged battery.On red, continuous The computer is on, running on battery power, and the charge level in the battery has reached a critical state. Plug the computer into an AC/DC power source or install a charged battery.orThe computer has encountered a fault and is not operating normally. Contact your computer support personnel, such as your help desk.orThe computer is off and you have inserted a battery that is at the critical low level and is incapable of running the computer.Table 1 Status LED indicator (continued)Mode/State LED State Meaning
Chapter 1. Getting StartedQuick-start guide26  iX104C5 User’s HandbookQuick-start guideThis section is a quick guide to using the main features of your tablet. (See Chapter 2 for detailed information.)Application, Windows, and hot keysCtrl-Alt-Delete(Secure AttentionSequence) keyScreen RotationkeyFunctionkeyHot key 1 Hot key 2Hot key 3 Fingerprint scanner
Chapter 1. Getting StartedQuick-start guideiX104C5 User’s Handbook  27Table 2 Main keysPress this key... To perform this functionLog on after resuming operation from power management, powering on, or locking.After logging on, launch Windows Task Manager.Rotate screen orientation between portrait (vertical) and landscape (horizontal).Use in combination with another key to perform various functions. (See page 27.)Fingerprint scanner.Display the Start menu. Open Internet Explorer, or perform a user-definable function. Put the computer in Sleep mode.Table 3 Function mode keysPress these keys... To perform this function   Default function: Send video display to a monitor or projection panel connected to the computer (and back to the computer again). You can program this key combination to perform a different function. (See “Programming hot keys to start applications, open documents, or go to a website” on page 61.)   Enable or disable Airplane mode, which toggles wireless radios on/off.   Bluetooth toggle.To define a function, see “Programming hot keys” on page 60.In the default configuration, the P3 key puts the computer in Sleep mode and the Power button shuts down the computer. To change these settings, see page 52.
28  iX104C5 User’s Handbook
iX104C5 User’s Handbook  292Using the TabletThis chapter contains detailed instructions for using the tablet.Turning on the computer1. Make sure the computer is off.2. Make sure the battery is charged or that the computer is plugged in to an external power source.3. Press the Power On/Off, Backlight On/Off, Sleep/Resume button.When the computer is off, the Status LED is off.Power On/Off,Backlight On/Off,Sleep/Resumebutton
Chapter 2. Using the TabletTurning off the computer30  iX104C5 User’s HandbookTurning off the computer1. If the computer is in Sleep mode, press the Power On/Off, Backlight On/Off, Sleep/Resume button to resume operation. (See page 32 for information about Sleep mode.)2. Make sure the battery is charged or that the computer is plugged in to an external power source.3. Save your work and close all programs.4. From the Windows Start menu, click Turn Off Computer.5. The Turn off computer dialog box opens.6. Click Turn Off or press the Power button continuously for more than 4 seconds.Using the Reset switchIf the computer does not seem to be accepting input and you cannot turn it off by using the method described in “Turning off the computer,” press the Reset switch. (Use the stylus or a similar instrument to press the switch). When the computer is in Sleep mode, the Status LED is breathing green.Power On/Off,Backlight On/Off andSleep/ResumebuttonUse the Reset switch only if you cannot turn off the computer by any other means, because you may lose unsaved data.Reset switch
Chapter 2. Using the TabletSuspending and resuming operationiX104C5 User’s Handbook  31Suspending and resuming operationTo conserve battery power when you do not want to turn off the computer or when you need to install a charged battery pack, put the computer into Sleep mode. (You can suspend operation without closing any programs or Windows.)When you suspend operation:■Programs that are running stop (but do not close).■Active data is saved.■The system enters one of the following low-power modes:• Sleep (Suspend-to-RAM) mode – The Status LED light is breathing green. Active data is saved in RAM and most other components are turned off. Although the computer uses very little power when in Sleep mode, eventually the battery’s power does run out. If you do not plan to use the computer for an extended period of time, turn the computer off or put it in Hibernation mode instead of Sleep mode.• Hibernation mode – Active data is saved on the SSD and power usage is reduced to the same level as when the computer is turned off. In Hibernation mode, there is no danger of losing data if battery power is lost.Notes:If you have set your computer to turn power off (in the Power Options utility in Windows Control Panel), you cannot suspend operation. To change power settings, see “Selecting Power (On/Off)/Backlight(On/Off)/Sleep/ Resume button options” on page 55.In the default configuration, the P3 key puts the computer in Sleep mode and the Power button shuts down the computer. To change these settings, see “Programming hot keys to perform pre-defined functions” on page 65. For more information, see “Checking battery power status” on page 52.
Chapter 2. Using the TabletSuspending and resuming operation32  iX104C5 User’s HandbookIf your computer is connected to a network, the network may automatically log you off after a period of inactivity while system operation is suspended. Contact your help desk or system administrator to learn your log-off time limit.Suspending operationUse one of the following methods to suspend operation:Method 1Press the P3 key.Method 2 1. Press the Windows Start button; then press the right arrow next to the Shutdown button.2. Press Sleep.When operation is suspended, the Status LED displays a breathing green light.In order to suspend operation, the Sleep option must be enabled in Windows Power Options. See “Selecting Power (On/Off)/Backlight(On/Off)/Sleep/ Resume button options” on page 55.P3 keyStatus LED
Chapter 2. Using the TabletSuspending and resuming operationiX104C5 User’s Handbook  33Resuming operationTo resume operation when the computer is in Sleep mode, press the Power On/Off, Backlight On/Off, Suspend/Resume button.Note: Press the button only once.Approximately 20 seconds later, the computer resumes normal operation. When the Status LED displays a continuous green light, you can begin using the computer.Power On/Off, Backlight On/Off, Sleep/Resumebutton
Chapter 2. Using the TabletUsing the pen34  iX104C5 User’s HandbookUsing the penYou can use any of the following methods to select items and to navigate through programs.■Auto-Sense mode: Use either the multifunction pen or your finger interchangeably. The computer distinguishes between the two input modes and automatically adjusts accordingly. This is the tablet’s default state.■Digitizer mode: Use only the special multifunction pen provided with the computer. For more information, see “Programming hot keys to perform pre-defined functions” on page 65.WARNINGDo not use items such as a ball point pen or a screwdriver that can damage the tablet. Damage caused by using an item not provided with the tablet is not covered by the tablet warranty.Note: During the first use of the tablet, or if the action you are trying to perform does not occur when you use the pen or your finger to touch the screen, calibrate the digitizer as described in “Calibrating the digitizer” on page 75.
Chapter 2. Using the TabletUsing the peniX104C5 User’s Handbook  35Using the digitizer to perform mouse functionsChanging the pen double-click speedThe pen double-click speed is in sync with the mouse double-click speed. To change the speed, follow the instructions below.1. Click the Windows Start button.2. Click the Control Panel option.3. In the Control Panel window, select Hardware and Sound > Set up your Pen and Tablet. 4. Drag the slider to a faster or slower speed.To perform this function... Do thisSelect an object (left button click).Tap the pen tip once on the object.Perform a double-click. Quickly tap the pen tip twice on the object.Perform a right-click. Hold the pen or your finger directly on the object for 1 second. Move or drag an object. Place the pen tip or your finger on the object; then continue to hold the pen tip or your finger against the screen as you move the pen or your finger.
Chapter 2. Using the TabletUsing the pen36  iX104C5 User’s HandbookPositioning the pen and pen tetherThe pen tether helps prevent the loss of your pen. The following illustrations show how to position the pen and pen tether.Tether anchored at the bottompen tetherpen
Chapter 2. Using the TabletUsing the peniX104C5 User’s Handbook  37Tether anchored on the sidepen tetherpen
Chapter 2. Using the TabletUsing the fingerprint scanner38  iX104C5 User’s HandbookUsing the fingerprint scannerThe fingerprint scanner and the associated Protector Suite 2009 software enable you to use fingerprint verification to protect the security of your data.The first step for using fingerprint verification is to enroll your fingerprint to create an association between your username, password, and fingerprint.After fingerprint enrollment you will be able to:■Use your fingerprint as part of computer login security.■Register Web pages and Windows applications to use your fingerprint instead of passwords.■Launch applications by swiping your finger the sensor.■Store confidential information in an encrypted form in a protected folder.To launch the Enrollment Wizard, select:Start > All Programs > Protector Suite > Control Center > User Enrollment and follow the wizard’s instructions.For more information about using the fingerprint scanner, see the Protector Suite 2009 User’s Guide PDF included on your hard disk in the Protector Suite 2009 folder.Fingerprint scanner
Chapter 2. Using the TabletChanging the screen orientationiX104C5 User’s Handbook  39Changing the screen orientationTo rotate the screen orientation from portrait (vertical) to landscape (horizontal) mode or from landscape to portrait mode, press the screen rotation key.portrait mode landscape mode
Chapter 2. Using the TabletAdjusting the screen brightness40  iX104C5 User’s HandbookAdjusting the screen brightnessUse either of the following methods to adjust the screen brightness:Method 11. Click Start.2. Open the Control Panel.3. In the Hardware and Sound area, select Adjust commonly used mobility settings. Use the Brightness slider to adjust the brightness.Method 21. In the Windows tasbar, click the power management icon; then select Adjust screen brightness.2. Move the slider bar (located at the bottom of the window) to change the screen brightness.Display brightness slider
Chapter 2. Using the TabletAdjusting the screen brightnessiX104C5 User’s Handbook  41Enabling automatic backlight controlWhen the Auto Light sensor is enabled, the computer automatically controls the amount of backlight sent to the screen to provide optimum brightness for the lighting conditions in which you are working.To enable automatic backlight control, see page 80.Optimizing screen settings for outdoor use1. Click Start > Control Panel > Appearance and Personalization > Personalization > Change desktop background.2. In the My Themes area, select  High Contrast White.3. Click the Back button.4. Click Display.5. Click Medium - 125% to enlarge the icon size; then click Apply.6. Click Adjust Resolution. Make sure the screen resolution setting is 1024 by 768 pixels; then click OK.Auto Light sensor
Chapter 2. Using the TabletDocking the tablet42  iX104C5 User’s HandbookDocking the tabletIf you have the optional xStand office dock or xDock vehicle dock, connect it to the tablet at the docking port. (See the iX104 Docking Stations Handbook.)Docking portGuide pin receptacles
Chapter 2. Using the TabletConnecting devicesiX104C5 User’s Handbook  43Connecting devicesRefer to the following subsections for information about connecting external devices to your computer.Note: If the device you want to use does not appear to be working with your computer, the device may need to be enabled in the computer’s configuration program. Contact your local help desk or Xplore reseller. Connecting to a local area networkConnect a local area network (LAN) cable’s RJ-45 connector to the internal LAN interface card. (See your network system administrator for more information.)Connecting USB-compatible devicesConnect any USB-compatible devices to the computer’s USB ports.LAN connectorUSB ports
Chapter 2. Using the TabletConnecting devices44  iX104C5 User’s HandbookConnecting an external microphoneAdjusting microphone volumeIf necessary, adjust the volume of the microphone as follows:1. Press the Windows Start key; then open the Control Panel.2. Select Hardware and Sound; then select  Sound.3. Select the Recording tab.4. Select Microphone; then select Properties.5. Select the Levels tab.6. Adjust the microphone volume or boost.7. Click OK.microphoneconnector
Chapter 2. Using the TabletConnecting devicesiX104C5 User’s Handbook  45Connecting a headphone or speakersAdjusting headphone or speaker volume 1. Click the audio icon in the Status area of the Windows taskbar.The volume control area opens.2. If the Mute button indicates that sound is muted, click the button to turn on the sound.3. Move the slider bar up or down to increase or decrease the volume.headphone/speakersconnector
Chapter 2. Using the TabletConnecting devices46  iX104C5 User’s HandbookConnecting a monitor or projection panel (optional)Activating the monitor or projection panelIf your tablet includes the optional monitor/projection panel connector, you can change the video output as follows:To change the video output to the monitor or projection panel:Press the Fn-P1 key combination.To change the video output back to the computer:Press the Fn-P1 key combination again.Monitor/projection panel connector
Chapter 2. Using the TabletConnecting devicesiX104C5 User’s Handbook  47Connecting a device to the serial port (standard)If your tablet includes the standard serial port, you can connect a terminal or other device that uses the RS-232, RS-422, or RS-485 data transfer standard.Connecting an XPL expansion module9-pin serial portXPL expansion portTablet with optional GPS II
Chapter 2. Using the TabletUsing the battery48  iX104C5 User’s HandbookUsing the batteryYou can recharge, remove, and replace the battery pack.Charging the battery packIf you do not have an external battery chargerFollow these steps to charge the battery while it is installed in the computer:1. Connect a power source, such as an AC adapter or cigarette lighter adapter, to the power connector on the computer.If the battery charge is below 95%, the battery begins charging and the Status LED flashes green. (If the battery charge is higher than 95%, the battery will not charge, preventing battery overcharge.)2. Check the level of charge. (See “Checking battery power status” on page 52.)The charging process continues until the battery charge reaches 100%.Powerconnector
Chapter 2. Using the TabletUsing the batteryiX104C5 User’s Handbook  49Table 4 shows the approximate time required to charge the battery level to 100%.If you have an external battery charger1. Remove the battery pack (see page 49).2. Use the external battery charger to charge the battery.3. Install the battery (see page 51).Removing and installing the batteryYou can remove the battery and use an (optional) external charger to charge it.Removing the battery1. To swap with a charged battery:Use one of the methods described in “Suspending operation” on page 32 to suspend operation.If a charged battery is not available:Save your work and close all running programs; then shut down the computer or put the computer in Hibernation mode (see “Suspending operation” on page 32).Note: To avoid losing unsaved data, wait until the computer has completed switching to Hibernation mode before removing the battery.Table 4 Approximate battery charge timeBattery pack capacity Charge time Battery pack P/N55 watt hours (7600 mAh) 1.5 hours 11-0101868.5 watt hours (9250 mAh) 2.5 hours 11-01019
Chapter 2. Using the TabletUsing the battery50  iX104C5 User’s Handbook2. Use the stylus or a pen to depress the battery lock button.The battery release latch returns to its original position.3. Pull the battery away from the computer and remove it.Note: After removing the battery, you must replace the battery or connect the computer to an external power supply within 3 to 5 minutes or the computer completely loses power.RemovablebatteryBattery releaselatchBattery lockbutton
Chapter 2. Using the TabletUsing the batteryiX104C5 User’s Handbook  51Installing the battery1. Orient the battery with the slides in the empty battery tray.2. Slide the battery into the tray and press it firmly until it is seated.3. Slide the battery release latch to its original position.The lock button pops back into the locked position, securing the battery in place.Discarding batteriesDispose of batteries in accordance with your local government regulations. Under federal, state, or local law, it may be illegal to put batteries in the trash. Contact your system administrator, municipal waste disposal department/provider for information.
Chapter 2. Using the TabletUsing power options52  iX104C5 User’s HandbookUsing power optionsDisplaying power optionsOn the Windows taskbar, click the battery icon; then select More power options. The Power Options window opens.Checking battery power statusOn the Windows taskbar, click the battery icon. The following window opens, displaying the percentage of power remaining in the battery:
Chapter 2. Using the TabletUsing power optionsiX104C5 User’s Handbook  53Selecting a power plan1. On the Windows taskbar, click the battery icon. The following window opens: 2. Select one of the following power plans: (select More power options in necessary)Balanced – Balance between computer performance and battery life.Power Saver – Longer battery life and lower performance.High performance – Higher performance and shorter battery life.
Chapter 2. Using the TabletUsing power options54  iX104C5 User’s HandbookSelecting power options1. On the Windows taskbar, right-click the battery icon.2. Select Power Options.The following window opens.3. Under the selected power plan, press Change plan settings.4. Select the power options you want to use.
Chapter 2. Using the TabletUsing power optionsiX104C5 User’s Handbook  55Selecting Power (On/Off)/Backlight(On/Off)/Sleep/ Resume button optionsTo change what happens when you press the button: 1. On the Windows taskbar, right-click the battery icon.2. Select Power Options.The following window opens.3. Press Choose what the power buttons do.4. Select the options you want to use.Power (On/Off)/ Backlight (On/Off)/Sleep/Resume button
Chapter 2. Using the TabletUsing power options56  iX104C5 User’s HandbookTips for conserving battery powerThe following tips help you extend the life of your battery by conserving battery power:■Use an external power source such as the AC or auto adapter whenever available.■Suspend operation if you know that you will not be using the system for a while. (See page 32.)■If you do not plan to use the computer for an extended period of time, turn it off.■Adjust power options to automatically conserve power. (See page 54.)■Adjust the display brightness to no brighter than necessary for comfortable viewing. The display can consume a large portion of the computer’s power. (See page 40.)■Set the LCD Brightness range to “Power Saving” in the BIOS Setup Utility. (See page 79.)
Chapter 2. Using the TabletAccessing the Solid State Drive (SSD) cartridgeiX104C5 User’s Handbook  57Accessing the Solid State Drive (SSD) cartridgeWhen you install a new storage drive, follow the instructions in this section to access the hard drive carrier.WARNING Failure to follow this procedure can result in damage to the case and the cover, which is not covered under the Xplore Technologies warranty. Xplore recommends that you use an approved Xplore Technologies service center for this procedure.1. Turn off the computer.2. Remove all power from the unit, including batteries and other power sources such as power supplies, cigarette lighter adapters, and mobile power sources.3. Pinch the two center pins with one hand while pushing down on the lever with the other. The drive carrier will pop up (like the battery) and permit removal. Note: Your drive carrier may have two screws installed. If so, remove them before you exchange the drive carrier.
Chapter 2. Using the TabletAccessing the Solid State Drive (SSD) cartridge58  iX104C5 User’s HandbookRe-installing the drive carrier1. Insert the drive with smooth edge into the bay at a slight angle. 2. Press down until the carrier clicks into place, while pinching the two center pins. 3. If your machine had the screws in place, re-attach them. Note: Do not use power tools.
Chapter 2. Using the TabletAccessing the MicroSD and SIM compartmentiX104C5 User’s Handbook  59Accessing the MicroSD and SIM compartmentWhen you install a MicroSD or SIM card, follow the instructions in this section to access the compartment.WARNING Failure to follow this procedure can result in damage to the case and the cover, which is not covered under the Xplore Technologies warranty. Xplore recommends that you use an approved Xplore Technologies service center for this procedure.1. Turn off the computer.2. Remove all power from the unit, including batteries and other power sources such as power supplies, cigarette lighter adapters, and mobile power sources.3. Remove the battery. (See “Removing and installing the battery” on page 49.)4. Lift up on the D-ring and turn it clockwise ¼ of a rotation. Once the lock is disengaged lift the door to open the compartment.Note:  This compartment can handle most MicroSD and SIM cards.Opening the compartment Installing a MicroSD card Installing a SIM card
Chapter 2. Using the TabletProgramming hot keys60  iX104C5 User’s HandbookProgramming hot keysXplore pre-programs the P1, P2, and P3 hot keys and Function mode hot key combinations to perform certain functions by default. However, you can program them to perform different functions, as described in this section.Table 5 Programmable hot keysKey Default functionOpens the Start menu.Starts Internet Explorer.Puts the computer in Sleep mode.Table 6 Programmable Function mode hot key combinationsKey combination Default functionSends video display to a monitor or projection panel.   Airplane mode toggle.   Bluetooth toggle.
Chapter 2. Using the TabletProgramming hot keysiX104C5 User’s Handbook  61Programming hot keys to start applications, open documents, or go to a website1. In the Status area of the Windows taskbar, click the iX104C5  Configuration icon.The Launch Button QuickShow dialog box opens.2. Click the Configure button.The Panel Control Center window opens.
Chapter 2. Using the TabletProgramming hot keys62  iX104C5 User’s Handbook3. Click the Change button next to the key or key combination you want to program.The following options appear:4. Click Launch an Application, Document or Web site.The following options appear:
Chapter 2. Using the TabletProgramming hot keysiX104C5 User’s Handbook  635. To start an application:a. Click Launch an Application.b. Press Browse to find the application you want the hot key or Function mode hot key combination to start (for example: word.exe, notepad.exe, excel.exe).c. Click Change.6. To open a document:a. In the Click Open a Document.b. Press Browse to find the document you want the hot key or Function mode hot key combination to open. (For example: spreadsheet.xls, airports.doc, wiringdiagram.jpg)c. Click Change.
Chapter 2. Using the TabletProgramming hot keys64  iX104C5 User’s Handbook7. To open a multimedia file:a. Click Open a Multimedia file.b. Press Browse to find the name of the multimedia file you want the hot key or Function mode hot key combination to open. (For example: 911training.dir, demo.ppt)c. Click Change.8. To open a Web page:a. Click Open a Web page.b. Press Browse to find the URL of the Web page you want the hot key or Function mode hot key combination to open. (For example: http://www.xploretech.com)c. Click Change.9. Program more hot keys, or click Close to close the Panel Control Center window.
Chapter 2. Using the TabletProgramming hot keysiX104C5 User’s Handbook  65Programming hot keys to perform pre-defined functions1. In the Status area of the Windows taskbar, click the iX104C5  Configuration icon.The Launch Button QuickShow dialog box opens.2. Click the Configure button.The Panel Control Center window opens.3. Next to the key or key combination you want to program, click the Change button.
Chapter 2. Using the TabletProgramming hot keys66  iX104C5 User’s HandbookThe following options appear:4. Click Start a pre-defined function.5. In the Function selection drop-down list, select an option.6. Program more hot keys, or click Close to close the Panel Control Center window.
Chapter 2. Using the TabletProgramming hot keysiX104C5 User’s Handbook  67Programming hot keys to perform other key functions1. In the Status area of the Windows taskbar, click the iX104C5  Configuration icon.The Launch Button QuickShow dialog box opens.2. Click the Configure button.The Panel Control Center window opens.3. Next to the key or key combination you want to program, click the Change button.
Chapter 2. Using the TabletProgramming hot keys68  iX104C5 User’s HandbookThe following options appear:4. Click Press a key or key combination.The following options appear:
Chapter 2. Using the TabletProgramming hot keysiX104C5 User’s Handbook  695. If you want the hot key or hot key combination to perform the function of a single key:a. If the Ctrl, Alt, or Shift boxes are checked, uncheck them.b. Click the key you want the hot key or hot key combination to perform. (For example: F6, G, or Caps Lock)If you want the hot key or hot key combination to perform the function of a key combination:a. Check the Ctrl, Alt, or Shift box.b. From the drop-down list, select the additional key, or click the key on the keyboard.ExamplesTo cause the hot key to perform the print screen function (Alt-Print Scrn): Check the Alt check box; then select PrtScr from the drop-down list.To cause the hot key to perform the paste function (Ctrl-V): Check the Ctrl check box; then click the V key.6. Program more hot keys, or click Close to close the Panel Control Center window.
70  iX104C5 User’s Handbook
iX104C5 User’s Handbook  713Maintaining the TabletThis chapter provides instructions for maintaining your tablet.Caring for the tabletThis section provides information about how to keep your tablet in top working condition.Checking power cords and connectorsCheck AC and DC power cords and power connectors periodically for damage. Replace the power cord immediately if you find any damage.Protecting the computer from damage■Your computer is designed to sustain a multiple-axis drop to a non-yielding surface. Do not intentionally drop the computer, because the cumulative effects of multiple drops may damage the computer.■Do not place heavy objects on the computer.■Do not disassemble the computer.■Keep the computer at least 5 inches (13 centimeters) away from any electrical appliance that generates a strong magnetic field, such as a motor, magnet, TV, refrigerator, or large audio speakers.
Chapter 3. Maintaining the TabletCaring for the tablet72  iX104C5 User’s HandbookPreventing the computer from overheatingThe computer monitors its internal temperature. As the internal temperature approaches the tolerable limits of heat-sensitive components, system functions are automatically limited or turned off to prevent damage.To prevent the computer from overheating, do not obstruct the computer’s air vents.air ventareaair vents
Chapter 3. Maintaining the TabletCaring for the tabletiX104C5 User’s Handbook  73Storing the computerYou can store the computer in the Off state for about 30 days with a fully charged battery installed. After this period, recharge the battery or replace it with a charged battery.If you intend to store the computer for more than 30 days, remove the battery pack and keep it in a cool place.Caring for the display screenTo clean the display screen, dampen a soft cotton cloth with water   and gently wipe the screen surface.Note: Do not use isopropyl alcohol to clean the screen. Alcohol may damage the surface of the screen.Protecting the display screenThe screen protector is a durable, replaceable writing surface that protects the display screen from abrasion.To obtain additional screen protectors, check with your reseller, or go to the Xplore Web site at www.xploretech.com for ordering information. Additional information about installation is included with the screen protectors.
Chapter 3. Maintaining the TabletWhen to replace the pen74  iX104C5 User’s HandbookRemoving the screen protectorSlide your fingernail under the edge of the screen protector and pull the protector away from the screen.Installing a new screen protectorFollow the instructions included with your screen protector replacement kit.Note: If a screen protector is already installed on the display screen, remove it before installing the new screen protector.When to replace the penWith use, the pen tip may become worn and can scratch the screen. If your pen exhibits one of the following problems, replace the pen:■The pen does not move freely across the screen.■The pen does not perform as expected.edge
Chapter 3. Maintaining the TabletCalibrating the digitizeriX104C5 User’s Handbook  75Calibrating the digitizerCalibrating the digitizer adjusts the cursor position on the screen relative to the position of the pen tip or finger. Calibrate the digitizer to adjust the distance error between where the pen or finger is actually touching the screen and where the computer is registering the pen or finger touch.You may need to calibrate the digitizer in the following situations:■You are using the computer for the first time.■The previous user of the computer writes with the opposite hand or at a different pen angle.■The computer has not been used for some time.■The computer has been serviced.1. From the Start menu, select Control Panel.The Control Panel opens.
Chapter 3. Maintaining the TabletCalibrating the digitizer76  iX104C5 User’s Handbook2. Select Hardware and Sound.3. In the Tablet PC Settings area, select Calibrate the screen for pen or touch input; then follow the instructions that appear on the screen..Hardware and SoundCalibrate the screen for pen or touch input
iX104C5 User’s Handbook  77ATroubleshootingTable 7 contains solutions to some problems. If you cannot solve the problem by taking the actions described, contact your local help desk or your reseller for further assistance.Table 7 TroubleshootingProblem Possible cause and solutionComputer will not start. • The battery may be defective or discharged to a critically low level. Connect an external power supply (such as the AC adapter) or install a charged battery. See “Using the battery” on page 48.• Internal components may be above or below the acceptable operating range (below -20° C or above 60° C). After the temperature returns to safe operating range the computer will start.The computer will not resume operation after being suspended.• The battery may be defective or discharged to a critically low level. When the battery reaches a critically low level, the computer is forced into Sleep mode to avoid a total system power failure. Connect an external power supply (such as the AC adapter) or install a charged battery. See “Using the battery” on page 48.• The computer may be at the critical thermal limit. To avoid damage to heat-sensitive components, the computer enters Sleep mode when the computer operates above 60° C. Operation automatically resumes when the computer cools to below 60° C. Move the computer to a cooler location.The Status LED is red, continuous. • The computer is on, running under battery power, and the charge level in the battery has reached a critical level. Plug the computer into an AC/DC power source or install a charged battery.• The system has encountered a fault and is preventing normal operation. Contact your local help desk.The Status LED is red, blinking. The computer is powered on, running under battery power, and the charge level in the battery is at a minimum warning level. Plug the computer into an AC/DC power source or install a charged battery.
Appendix A. Troubleshooting78  iX104C5 User’s HandbookDisplay screen is blank or difficult to read.• Confirm that the computer is on (the Power icon is displayed continuously in the Status area).• The brightness may be set too low, causing the screen to appear too dark. To change system brightness, press the Fn and Start keys to open the Xplore menu and adjust the brightness. (See page 27.)• An external monitor may be selected. Press the Fn and P1 keys to select the computer display screen. (See page 27.)• The video time-out may have expired. Tap the display screen to reactivate the display. Note: This is a normal, power-saving feature. • If the Status light is blinking red, the computer is in Sleep mode because the temperature is below -20° C or above 60° C. When the temperature returns to a safe operating range, the display screen automatically comes back on. If possible, move the computer to a warmer or cooler location.• If the Status light is continually yellow, the computer is in Sleep or Hibernate mode. Press the Power On/Off key to resume.Cursor is not tracking the pen. Calibrate the pen. See “Calibrating the digitizer” on page 75.Computer is not responding to the pen. Connect an external USB keyboard to the computer. If the computer does not respond to the external keyboard, the application or operating system may have been corrupted. Press the Reset key. (See page 30.) If the system responds to a keyboard but not to the pen, contact your local help desk or reseller for further assistance. Headphone or speaker volume is too low.• The volume may be in Mute mode or set too low. Follow the instructions in “Adjusting headphone or speaker volume” on page 45.• Make sure the volume control in your audio software is set to an audible level. An external device is not working with the computer.The device may need to be enabled in the computer’s configuration program (BIOS Setup). Contact your local help desk or reseller. Table 7 Troubleshooting (continued)Problem Possible cause and solution
iX104C5 User’s Handbook  79BUsing BIOS and AOS Functions This appendix explains how to use the application and navigation buttons with the Basic Input-Output System (BIOS) program and the Advanced Operating System (AOS) Options menu.Note: These functions are typically for use only by your system administrator or by authorized service technicians.Note:  Each button has its own blue-light LED. No matter which button you press, every blue-light LED is on for about 3 seconds, then off. When in Shifted mode, all blue-light LEDs flicker.Table 8 Using BIOS and AOS functionsIn Shifted ModeButton BIOS Key Function BIOS Key Function   F1 F1 continues message. Up Arrow Navigate up through Multi Boot options and BIOS menus.   F2 Start the BIOS program: When the computer is booting, press the P2 button and follow the instructions that appear on the screen.Down Arrow Navigate down through Multi Boot options and BIOS menus.F8 Prompt Windows to select Safe mode.Right Arrow Navigate to the right.F11(Lock Fn)• Press for less than one second for F11 function.• Press longer to enable Shifted mode.Release FunctionPress once to exit Shifted mode.F12 Enter Multi Boot mode. F4 Change a BIOS setup value.Ctrl+Alt+Del Reboot. Enter Enter.
Appendix B. Using BIOS and AOS FunctionsDisabling the Auto Power feature80  iX104C5 User’s HandbookDisabling the Auto Power featureWhen Auto Power is enabled, the tablet automatically turns on if you dock it and the following conditions exist:■The tablet is off or in Hibernation or Sleep mode.■The dock or the tablet is connected to an external power source (including power applied when a vehicle’s ignition is started).If you dock the tablet and the tablet is off and no power is present, the tablet turns on as soon as power is applied.To disable the Auto Power feature:1. When the computer is booting, press the P2 button to access the BIOS Setup Utility.2. Select the Advanced tab.3. Disable the Dock with Auto Power On option.Enabling automatic LCD backlight controlWhen the LCD backlight control is in manual mode, the ambient light sensor is disabled and the computer does not automatically control the screen brightness.Follow these steps to enable automatic LCD backlight control:1. When the computer is booting, press the P2 button to start the BIOS Setup Utility.2. Select the Main tab.3. In the LCD Backlight Control drop-down list, select Automatic.4. Click OK.Note:  When the tablet is in the docking station, it will shut down or go into Hibernation or Sleep mode the same as it does when not in the docking station.
iX104C5 User’s Handbook  81CGlossaryAdapter. A device that provides an interface between two dissimilar electronic devices. For example, the AC adapter modifies the power from a wall outlet for use by the computer.Advanced Power Management (APM). A facility consisting of one or more layers of software that support power management. The APM software interface enables applications, operating systems, device drivers, and the APM BIOS to work together to reduce power consumption.Alternating Current (AC). Electric current that reverses its direction of flow at regular intervals.Analog signal. A signal with characteristics such as amplitude and frequency that vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals.Application. A program that performs specific tasks on your computer, such as word processing or creating spreadsheets.BIOS. Programs that contain such basic hardware operations as an interaction with diskette drives, hard disk drives, and the memory.Board. A circuit board. An internal card containing electronic components called chips, which perform a specific function or increase the capabilities of the system.Boot. To load a program or operating system into system memory.Bits Per Second (BPS). In serial transmission, the instantaneous bit speed with which a device or channel transmits a character.Card. Synonym for board; see board.Compact Disk-Read Only Memory (CD-ROM). Stores data on metal-plated plastic discs.
Appendix C. Glossary82  iX104C5 User’s HandbookCompatibility. 1.The ability of one computer to accept and process data in the same method as another computer without modifying the data or the media upon which it is being transferred. 2.The ability of one device to connect or communicate with another system or component.Configuration. The specific combination of hardware components of the computer, and their operating status. The configuration of your computer includes pre-defined memory, type and speed of microprocessor, type of and size of hard disk drive, etc.Default. The preset parameter value automatically selected by the computer when you or a program do not provide instructions.Device driver. A program that controls communication between a specific peripheral device (such as a printer or the pen/stylus) and the computer.Disk drive. The physical device that enables the computer to read from, and write to, a disk.Display. An image-producing device used to view computer output.Double-click. To press and release the pen/stylus twice within a time frame you define, without moving the pointer off the choice.Hardware. The physical electronic and mechanical components of a computer system. typically, the computer itself, CPU, memory, etc.Hertz. A unit of wave frequency that equals one cycle per second.Interface. 1. Hardware and/or software components used specifically to connect one computer or device to another. 2. To physically connect one system or device to another to exchange information. 3. The point of contact between user, the computer, and the program (for example, the pen/stylus or a menu). JBOD. Two drives that appear in Window as two drives, Drive C and Drive D.
Appendix C. GlossaryiX104C5  User’s Handbook  83Kilobyte (KB). A unit of 1024 bytes measuring storage space, typically in memory or on storage media such as a diskette or hard disk drive.Local area network (LAN). Assembly of separate computers into an integrated network that connects the various computers together and to common devices such as printers and fax machines.Light Emitting Diode (LED). A semiconductor device that emits light when a current is applied.Liquid Crystal Display (LCD). liquid crystal sealed between two sheets of glass coated with transparent conducting material. Applying a voltage between the glass sheets darkens the liquid crystal to provide contrast to lighted portions of the display.Megabyte (MB). A unit of data storage equal to 1024 kilobytes.Megahertz (MHz). a unit of wave frequency that equals 1 million cycles per second.Modem. A device that connects your computer to a telephone line, allowing it to communicate with another computer at another location.Pen. See stylus.Peripheral device. An input/output device that is external to the central processor and/or main memory such as a printer or scanner.Pixel. Picture elements (tiny dots) that compose a screen image. Port. The electrical connection through which the computer sends and receives data to and from devices or other computers.Program. A set of instructions a computer can execute to tell the system what to do and how to do it.RAID 0. Two drives appear in Windows as one larger drive (two 80GB drives appear as one 160GB drive).
Appendix C. Glossary84  iX104C5 User’s HandbookRAID 1. One drive has information mirrored to a duplicate drive. For example, information from one 80GB drive is mirrored to another 80GB drive. The two drives appear in Windows as a single drive.Random Access Memory (RAM). A hardware component of your computer that temporarily stores active program code and data.Reset. The act of hard stopping/shutting down the operating system.Resolution. The number of pixels displayed on the screen. A higher resolution provides greater clarity and allows more information to be displayed on the screen at once.Restart. Resetting a computer without turning it off (also called warm boot or soft reset).Resume. The act of returning the computer to an active, operational state.Read Only Memory (ROM). The portion of your computer’s memory that contains permanent instructions, and which cannot be modified.Sleep mode. A power conservation mode in which electrical current is removed from most components of the computer.Solid State Drive (SSD). A sealed mass storage device used for storage and fast retrieval of programs and data. The SSD is contained in a drive cartridge for easy removal.Status Indicator (LED). a light above the LCD screen which indicates the current status of a particular device or hardware component.Stylus. A writing instrument. For pen computers, the stylus is used to interface with the LCD and digitizer.
Appendix C. GlossaryiX104C5  User’s Handbook  85Subscriber Identity Module (SIM). A smart card inside a GSM (Global System for Mobile communications) cellular device that encrypts voice and data transmissions and stores data about the specific user so that the user can be identified and authenticated by the network supplying the phone service. A SIM can be moved from one device to another and/or different SIMS can be inserted into any GSM radio.Universal Serial Bus (USB). A serial interface that enables communication between devices and the computer.
86  iX104C5 User’s Handbook
iX104C5 User’s Handbook  87DHardware Specifications* Varies according to your computer’s configuration.* Varies according to your computer’s configuration.PhysicalDimensions 11.20” x 8.25” x 1.6” (WxHxD)283.9mm x 209.3mm x 40.8mmWeight 5.25 lbs. (2.38 kgs)*ProcessingCPU Intel® i7® Core 620UE processor – Ultra Low VoltageChip set Intel QM57Processor speed 1.06 GHz*Memory/storageMain RAM • 1GB – 8GB DDR III RAM (2GB standard)• 144-pin SODIMM modulesRAM options 2GB, 4 GB, 8GB DDR III (optional)L2 Cache 4MB smart cacheBIOS ROM 8Mbit (FWH)Storage 40GB SSD, or 80GB SSD, single or dual for RAID 0/1 and JBOD support
Appendix D. Hardware Specifications88  iX104C5 User’s HandbookDisplayDisplay • Color LCD• Active Digital Sensor and Pen (iX104C5   andResistive Touch Panel (iX104C5 Dual Mode)• 32-bit True color• 10.4” TFT XGA (1024x768), 16M colors• Brightness: 100 levels (min.)• Viewing Angle:- Horizontal: 30 degrees (min.)- Vertical: 10 degrees (min.) - Contrast Ratio: Typ. 600:1, Min 100:1VRAM Intel i7 delivers low-power, hgh-performance 3D/2D graphics, video, and display capabilities, Intel HD graphics with Dynamic Frequency delivers graphics performance boost to graphics-intensive applications.
Appendix D. Hardware SpecificationsiX104C5  User’s Handbook  89InterfaceWireless Radio Bays • One full mini-PCI Express slot for WWAN (3G)• One half mini-PCI Express slot for WiFiIntegrated Interfaces • DC-in• USB (2) 2.0• Microphone Jack• Headset Jack•LAN (RJ-45)• 9-pin serial port)oroptional 15-pin D-SUB connector for external VGA monitor KeyPad / User Controls • Application buttons with primary and secondary functions• Power On/Off/Suspend/Resume button• Emergency Shutoff/Reset buttonAudio • Realtec ACC 262• On-board microphone with noise cancellation• On-board integrated stereo speakers (1W each)Status Indicators Power, Charge/DC-in, Warning
Appendix D. Hardware Specifications90  iX104C5 User’s HandbookPowerMain Battery • 10 cell 11-01019• Removable Lithium Ion • 7.4V @ 9250mAh (68.5 Whr)• Warm-swappable• Recharge time: 2.5 hours (100%)• Life: Up to 6.5 hours. (Battery life is dependent on operating system, power management, and applications in use.)• Suspend life: Min. 6 days• Off state: Approximately 90 daysOptional Spare Battery • 8 cell, 11-01018• Removable Lithium Ion• 7.4C @ 7600mAh (55 Whr)• Warm-swappable• Recharge time: 2.5 hours• Life: Up to 4.5 hours. (Battery life is dependent on operating system, power management, and applications in use.)• Suspend life: Min. 5 days• Off state: Approximately 30 days• (IP65 only)Bridge Battery • 6-cell Li Ion, 45mAh• Life: (with Suspend-to-RAM on bridge battery only): 3 to 5 minutes from full chargeAC Adapter Auto-sensing 100-240V, supplying 19 VDC, with a current of 3.42 A
Appendix D. Hardware SpecificationsiX104C5  User’s Handbook  91EnvironmentalTemperature • Operating: -7o to 140o F (-20o to 60o C) (iX104C5M minimum is -49o F,-45o C)• Storage: -40o to 167o F (-40o to 75o C)Humidity 0% to 95% non-condensingShock/Drop Four-foot drop to concrete, all surfaces, edges and cornersVibration 0.04g^2/Hz, 20 Hz - 1000 Hz-6dB/octave 1000 Hz - 2000 HzEnclosure Class Blowing rain:4”/hr, 40 mph wind and MIL-STD-810G Method 506.5 Procedure 1Ingress protection:IEC (60529) ingress tested to an IP67 standardSand and dust:Particle size < 149 µm, 10 + 7 g/m3 particle density 1.5 m/s to 8.9 m/s wind speedMIL-STD-810G Method 506.5 Procedure 1Salt Fog:5% saline for 48 hr (12 hr wet, 12 hr dry, 2 cycles)MIL-STD-810G Method 506.5Contamination by fluids:Detergents, brake fluid, aromatic hydrocarbonsMIL-STD-810G Method 506.5Solar radiation:1120 W/m2 (355 Btu/ft2/hr) UVB @ 50° C, 7x24 hr cyclesMIL-STD-810G Method 506.5
Appendix D. Hardware Specifications92  iX104C5 User’s HandbookAgency approvalsEMC • CFR 47, FCC part 15B, IC ICES-003• European Union Directive 2004/108/EC RTT&ESafety • TUV Bauart, RoHS, 2002/95/EC, WEEE• IEC600950-1 2nd Ed., EN60950-1 2nd Ed., UL60950-1 2nd Ed.• ETL Listed: ANSIISA-12.12.01-2007, C22.2 No. 213• UL1604Operating systemOperating Systems • Microsoft Windows 7 Professional – English, 32- and 64-bit
iX104C5  User’s Handbook  93EAgency NoticesFCC noticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Modifications not expressly approved by Xplore Technologies could void this user’s authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -  Reorient or relocate the receiving antenna.-  Increase the separation between the equipment and receiver.-  Connect the equipment into an outlet on a circuit different from   that to which the receiver is connected.-  Consult the dealer or an experienced radio/TV technician for help.
Appendix E. Agency Notices94  iX104C5 User’s HandbookIC regulationsThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement."The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems; the maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit; and The maximum antenna gain permitted (for devices in the band 5725-5850 MHz) to comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate, as stated in section A9.2(3). In addition, High-power radars are allocated as primary users (meaning they have priority) of the band 5250-5350 MHz and this radar could cause interference and/or damage to LE-LAN devices.The County Code Selection feature is disabled for products marketed in the US/Canada. For product available in the USA/ Canada markets, only channel 1~11 can be operated. Selection of other channels is not possible.IC radiation exposure statementThis EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528.
Appendix E. Agency NoticesiX104C5 User’s Handbook  95RF exposure Tests for SAR are conducted using standard operating positions specified by the FCC with the tablet PC transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the tablet PC while operating can be well below the maximum value. This is because the tablet PC is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a tablet PC model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., on the body) as required by the FCC for each model. (Body-worn measurements may differ among tablet PC models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various tablet PCs and at various positions, they all meet the government requirement for safe exposure. This device was evaluated and shown to comply with FCC SAR guidelines. Avoid covering or holding antennas when transmitting. Antenna locations are shown in the following figure.Health and Safety InformationExposure to Radio Frequency (RF) SignalsYour wireless tablet PC is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio AntennasBluetoothantenna
Appendix E. Agency Notices96  iX104C5 User’s Handbookfrequency (RF) energy set by the Federal Communications Commission of the U.S. Government as well as the RTT&E directive. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on the safety standards previously set by both U.S. and international standards bodies: ■American National Standards Institute (ANSI) IEEE. C95.1-1992■National Council on Radiation Protection and Measurement (NCRP). Report 86. 1986■International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1996■Ministry of Health (Canada), Safety Code 6. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.■European Union RTT&E Directive for SARThe exposure standard for wireless mobile tablet PCs employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The SAR limit set by the RTT&E is 2.0W/kg.Note: In the U.S. and Canada, the SAR limit for mobile tablet PCs used by the public is 1.6 watts/kg (W/kg) averaged over 1 gram of tissue. In Europe the SAR limit for mobile table PCs used by the public is 2.0 watts/kg (W/kg) averaged over 10 grams of tissue.The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations.DOC (Industry Canada Notices)Notice to Users of Radio and TelevisionThis Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations per the ICES-003CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.
Appendix E. Agency NoticesiX104C5 User’s Handbook  97Notice to Users of the Canadian Telephone NetworkNotice: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Xplore or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line. Notice: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. UL NoticeThis unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 19 VDC, with a current of 3.75 A. AC Adapter output polarity:For authorized repair technicians onlyWARNINGFor continued protection against risk of fire, replace only with the same type and rating fuse.
Appendix E. Agency Notices98  iX104C5 User’s HandbookWARNINGDanger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instruction.System disposalIn the event of system disposal, observe the following information regarding proper procedures in the State of Vermont.The liquid crystal display (LCD) lamps used in this system contain mercury. In the event of system disposal, be sure to follow local guidelines.Intel Advanced-N 6200 Country-specific Compliance StatementsHereby, Xplore Technologies, declares that the Intel Advanced-N 6200 complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the CE symbol and can be used throughout the European community.Option NV GOBI3000 Country-specific Compliance StatementsHereby, Xplore Technologies, declares that the Option NV GOBI3000 complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the CE symbol and can be used throughout the European community.Option NV GOBI2000 Country-specific Compliance StatementsHereby, Xplore Technologies, declares that the Option NV GOBI2000 complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the CE symbol and can be used throughout the European community.Sierra MC8795V Country-specific Compliance StatementsHereby, Xplore Technologies, declares that the Sierra MC8795V complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the CE symbol and can be used throughout the European community.
Appendix E. Agency NoticesiX104C5 User’s Handbook  99
Appendix E. Agency Notices100  iX104C5 User’s Handbook
Appendix E. Agency NoticesiX104C5 User’s Handbook  101
Appendix E. Agency Notices102  iX104C5 User’s Handbook
Appendix E. Agency NoticesiX104C5 User’s Handbook  103
Appendix E. Agency Notices104  iX104C5 User’s Handbook
iX104C5  User’s Handbook  105FEnvironmental Policy and Recycling ProgramEnvironmental policyXplore Technologies is committed to managing health, safety and environmental (HS&E) matters as an integral part of our business. In particular, it is our policy to assure the HS&E integrity of our processes and facilities at all times and at all places. We will do so by adhering to the following principles:ComplianceWe will comply with applicable laws and regulations and will implement programs and procedures to assure compliance. Compliance with HS&E standards will be a key ingredient in the training, performance reviews, and incentives of all employees.Risk reduction, prevention, and resource managementWe will seek opportunities, beyond compliance requirements, for reducing risk to human health and the environment, and we will establish and meet our own HS&E quality standards where appropriate.We will employ management systems and procedures specifically designed to prevent activities and/or conditions that pose a threat to human health, safety, or the environment. We will look for ways to minimize risk and protect our employees and the communities in which we operate by employing clean technology, including safe technologies and operating procedures, as well as being prepared for emergencies.We will strive to minimize releases to the air, land, or water through use of cleaner technologies and the safer use of chemicals. We will minimize the amount and toxicity of waste generated and will ensure the safe treatment and disposal of waste. We will manage scarce resources, such as water, energy, land, and forests in an environmentally sensitive manner.
Appendix F. Environmental Policy and Recycling ProgramTake back and recycling program106  iX104C5 User’s HandbookCommunicationWe will communicate our commitment to HS&E quality to our employees, vendors, and customers. We will solicit their input in meeting our HS&E goals and in turn will offer assistance to meet their goals.Continuous improvementWe will measure our progress as best we can. We will review our progress at least on an annual basis. We will continuously seek opportunities to improve our adherence to these principles, and will periodically report progress to our stakeholders.Take back and recycling program Send us your unwanted Xplore products and/or batteries or find a recycling center near you. If your old Xplore product and/or batteries have no value or you want to recycle in a socially and environmentally responsible manner, go to http://www.xploretech.com/contact and submit a technical support request as follows:1. From the drop-down menu, select Reason; then select Technical support. 2. Fill in the remaining fields. 3. Under Message, type I want to recycle my product. 4. Click Submit.An Xplore Technologies specialist will contact you with shipping instructions.Alternatively, you can leave your unwanted Xplore products at a local recycling center. For batteries, Xplore Technologies has partnered with Call2Recycle® (http://www.call2recycle.org/). Call2Recycle is a program of the Rechargeable Battery Recycling Corporation (RBRC) that promotes environmental sustainability by providing free battery and cell phone recycling in North America. RBRC is a 501(c)4 nonprofit public service organization.
Appendix F. Environmental Policy and Recycling ProgramEnvironmental and Sustainability Corporate ReportiX104C5 User’s Handbook  107If you prefer to have Xplore Technologies recycle your battery packs, submit a technical support request as described above.For the return of any Xplore product other than batteries, Xplore Technologies has partnered with R2 Solutions (http://www.r2solutions.org/). R2 Solutions (R2S) is a non-profit organization established to promote R2 practices as a major step towards making responsible electronics recycling business as usual across the United States and abroad. To find a location near you, go to R2 certified recycler locations (http://asoft552.accrisoft.com/certified/electronic-recyclers-with-r2-certified-facilities/). If you do not have access to the Internet, contact our technical support at (866) 296-8541 ext. 222.Environmental and Sustainability Corporate ReportAs the manufacturer of the world’s most advanced ruggedized tablet PC and peripherals, Xplore Technologies is recognized for the efficient design and manufacturing of it products. In our inaugural Environmental and Sustainability Corporate Report we outline our plans and aspirations to sustain our environment. As you review this report, we welcome your candid feedback. We know that CSER is a journey and your input will help us along the way.In 2011, Xplore Technologies Corporation of America established the Xplore Technologies Environmental committee to proactively work with stakeholders including customers, nongovernmental organizations (NGOs), and other interested groups on environmental issues. As a result of the committee's work, we have implemented initiatives to improve our performance across the spectrum of corporate environmental responsibility issues. Our progress on implementing these issues is outlined in this report.Although the Xplore Technologies Environmental committee has only been active since 2012, we have always cared for the environment and this has been a core value since Xplore Technologies was founded more than 15 years ago. We are proud of our accomplishments to date and, we are committed to continuously improve in the future.
Appendix F. Environmental Policy and Recycling ProgramEnvironmental and Sustainability Corporate Report108  iX104C5 User’s HandbookPublishing this report is a significant step toward the goal of becoming an environmental sustaining leader of our industry. Going forward, we will persist to perfect our environmental performance and transparency. We will also leverage our role as an industry leader and actively support international organizations and industry associations working to improve environmental conditions.The Xplore Technologies 2012 Environmental and Sustainability Corporate Report is located at http://www.xploretech.com/environment. To obtain the report, click Environmental Sustainability Report 2012. Feel free to save this to your personal files. If you do not have access to the Internet, call Xplore technical support at (866) 296-8541 ext. 222 and request that a digital copy be sent to your email address.
iX104C5  User’s Handbook  109IndexAair flow vents, location 21ambient light sensor, location 19antenna covers, location 20Auto Light sensor, disabling 41Auto Power feature, disabling 80Bbattery packcharge time 49charging 48checking the charge 48conserving power 56installing 51location 20removing 49battery release latch, location 20BIOS Setup Utility, using 79Cconvection air flow cover, location 20Ddigitizercalibrating 75using to perform mouse functions 35double-click, performing with pen 35dragging and dropping, performing with pen 35EEnvironmental and Sustainability Corporate Report 107Environmental policy 105Hheadphone connector, location 22headphone volume, adjusting 45headphone, connecting 45Hibernation mode, description 31hot keys, programming 61hot keys, programming,    see keys, programming hot keysIInternet Explorer, starting 27iX104accessories 15preventing overheating 72protecting from damage 71storing 73KKensington lock slot, location 21keysCtrl-Alt-Del 27description 27Ctrl-Alt-Deletelocation 26descriptions 27Functiondescription 27location 26Function mode hot key combinationsdefault functions 60descriptions 27P1default function 60location 26
Index110  iX104C5 User’s HandbookP2default function 60description 27location 26P3location 26Power On/Off/Sleep/Resume, location 55programming hot keys 60, 61to perform other key functions 67to perform pre-defined functions 65quick-start diagram 26Screen Rotationdescription 27location 26Secure Attention Sequence (SAS) 26LLAN connector, location 22LCD backlightdisabling automatic control 41enabling manual control 80LEDs 24Status LED meanings 24left button click, performing with pen 35local area network (LAN), connecting to 43logging on 27Mmicrophoneconnecting external 44connector location 22location 19volume, adjusting 44monitoractivating 46connecting 46sending video display to 27mouse functions, performing 35Ppendouble-click speed, changing 35dragging and dropping 35holder, location 20location 20performing a double-click 35performing a right-click 35performing left button click 35positioning in holder 36replacing 74tether, using 36Power (On/Off)/Backlight (On/Off)/Sleep/Resume     key, location 55power connector, location 22Power On/Off/ Suspend/Resume key, location 21power use, managing 52projection panelactivating 46connecting 46sending video display to 27Qquick-start guide 26Rrecycling program 106Reset switchlocation 19using 30resuming operation 33right-click, performing with pen 35RJ-45 connector 22Sscreenlandscape mode 27portrait mode 27protecting 73
IndexiX104C5 User’s Handbook  111screen orientationchanging 39landscape 39portrait 39screen protectorinstalling 74removing 74replacing 74serial portcompatible devices 47location 47Sleep modeending 33starting 32Sleep mode, description 31speaker volume, adjusting 45speakersconnecting 45location 19storing the computer 73support, contacting 17suspending operation 32Ttroubleshooting 77turning off the computer 30turning on the computer 29UUSB port, location 22USB-compatible device, connecting 43Vvideo outputchanging from monitor to computer 46changing to monitor 46volumeadjusting headphone 45adjusting microphone 44adjusting speaker 45WWindows Task Manager, launching 27XXPL expansion module, connecting 47XPL2 port 21, 23Xplore Technologies, contacting 17
112  iX104C5 User’s Handbook

Navigation menu