Yaesu Musen 10443250 Rack Mount Repeater User Manual VXR 9000V H p65

Yaesu Musen Co., Ltd. Rack Mount Repeater VXR 9000V H p65

Contents

Users Manual

Download: Yaesu Musen 10443250 Rack Mount Repeater User Manual VXR 9000V H p65
Mirror Download [FCC.gov]Yaesu Musen 10443250 Rack Mount Repeater User Manual VXR 9000V H p65
Document ID556895
Application ID8C6Maf19QcgQN/VHXaj+2Q==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize37.8kB (472549 bits)
Date Submitted2005-06-29 00:00:00
Date Available2005-06-29 00:00:00
Creation Date2005-05-06 08:39:34
Producing SoftwareAcrobat Distiller 5.0 (Windows)
Document Lastmod2005-06-01 21:06:07
Document TitleVXR-9000V-H.p65
Document CreatorPageMaker 6.5J
Document Author: manual

FCC ID: K6610443250/IC ID: 511B-10443250
RACK MOUNT REPEATER
VXR-9000-H
OPERATING MANUAL
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
INTRODUCTION
The VXR-9000 is commercial-grade 50-watt FM repeater designed to provide reliable two-way full-duplex communications over a wide range of environmental conditions.
Designed to mount in a standard 19-inch rack, the VXR-9000 is crafted using the latest computer-aided design and
manufacturing processes, to ensure a high level of reliability to users. Important channel frequency data is stored in
EEPROM, and is easily programmable by a Servicing Technician or Dealer using an IBM compatible personal computer and the VPL-1 Programming Cable and CE60 Software.
Please take a few minutes to read this manual carefully. The information presented here will allow you to derive
maximum performance from your VXR-9000. After reading it, keep this manual handy for quick reference, in case
questions arise later on.
Important Note: Internal service work, programming, and accessory installations should only be performed by your
authorized Vertex Standard Dealer. Dangerous conditions and/or possibly illegal operation may result from improper setup, programming, or internal modifications.
SAFETY/WARNING INFORMATION
The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures with a
separation distance of at least 1.98m
74cm from all persons during normal operation and must not exceed an
antenna gain of 0 dBd. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. The antenna(s)
used with this device must satisfy the antenna co-location requirements of 47 C.F.R. 1.1307(b)(3).
NOTICE!
 Do not modify this repeater for any reason.
Refer service of this repeater to qualified technicians only.
 When the repeater become abnormal, such as the overheating, smoke smell of burning, etc., turn the main
power switch off and disconnect the Main Power Source connector from the rear of the VXR-9000 immediately. Also disconnect any backup power source you may have connected to the rear of the VXR-9000.
 Do not place any combustible material near the repeater.
 Do not spray any liquid over the repeater.
 Ensure that the power and antenna connections are securely made, using cables with excess capacity for
the power being utilized.
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
FRONT PANEL CONTROLS & CONNECTORS
 POWER (O/I) Switch
This is the main power switch for the repeater.
 Power Indicator (MAIN)
This LED glows green when the main power source
is used.
 Power Indicator (BACKUP)
This LED glows red when the backup power source
is used.
 MIC Jack
Connect the microphone plug to this jack. This jack
is also used for writing and reading channel frequency or other configurations via the COM Port of
the PC on which the clone editor (CE60) is running.
 Programmable Function (PF) Key
Six pushbuttons on the front panel are programmable function (PF) keys, each with an orange indicator inside. Each key can be programmed with
two functions, one for a “long” press and one for a
“momentary” press. The PF key functions may be
customized, via programming by your VERTEX
STANDARD dealer, to meet your communications
network requirements. Note that some functions
may require the purchase of optional internal accessories. The possible PF key features and functions are explained on the pages to follow.
 TX Indicator
This LED glows red when the repeater is transmitting.
 Numeric Display
This display consists of two 7-segment LEDs, indicating the channel number during normal operation. If an abnormal condition arises, an error code
will be displayed:
DISPLAY
DESCRIPTION
01 - 32
PC
UL
HI
SC
LC
E1
E2
E5
E7
E3, E4, E6, E9
Channel Number
Clone Active
PLL Unlock
High temperature in PA Unit
Scan Active
Front Panel Keys are Locked
PTT key is Disabled
Cooling Fan is Disabled
Low Voltage in Backup Battery
PA Unit Abnormality
Contact your Dealer
BUSY Indicator
This LED glows green when the receiving channel
is busy.
Speaker
The internal speaker is located here.
 VOL Knob
This control knob adjusts the output level of the
front speaker and external speaker jack on the back
panel.
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
PROGRAMMABLE FUNCTION (PF) KEY DETAILS
FUNCTION
PF-1 KEY
PRESS PRESS & HOLD
PF-2 KEY
PRESS PRESS & HOLD
PF-3 KEY
PRESS PRESS & HOLD
PF-4 KEY
PRESS PRESS & HOLD
PF-5 KEY
PRESS PRESS & HOLD
PF-6 KEY
PRESS PRESS & HOLD
CH DOWN
CH UP
COMPANDER
CTCSS/DCS ENC
CTCSS/DCS DEC
CW ID
TWO TONE DEC
CW ID SIGNAL
CW MESSAGE 1
CW MESSAGE 2
CW MESSAGE 3
CW MESSAGE 4
CW MESSAGE 5
CW MESSAGE 6
CW MESSAGE 7
CW MESSAGE 8
DC POWER SAVE
ENCRYPTION
ENCRYPTION CODE
KEY LOCK
LOCAL PTT
MONITOR
MONITOR M
MULTI TONE
PANEL INDICATOR
REMOTE
REPEAT
RESET
SCAN
SQUELCH
TEST TONE
TEST TONE M
TOT
TRANSMIT
TX POWER MID
TX POWER LOW
CH DOWN
CTCSS/DCS ENC
Press (or Press and hold in for one second) the PF key
assigned to “CH Down” to step to the next-lower operating channel.
Press (or Press and hold in for one second) the PF key
assigned to “CTCSS/DCS Enc” to turn the CTCSS/DCS
Encoder “On” or “Off” (toggle).
CH UP
CTCSS/DCS DEC
Press (or Press and hold in for one second) the PF key
assigned to “CH Up” to step to the next-higher operating channel.
Press (or Press and hold in for one second) the PF key
assigned to “CTCSS/DCS Dec” to turn the CTCSS/DCS
Decoder “On” or “Off” (toggle).
COMPANDER
CW ID
Press (or Press and hold in for one second) the PF key
assigned to “Compander” to turn the Compander circuit “On” or “Off” (toggle). This function is only activated on the “Narrow Channel Spread” of the “Base
Transceiver” mode.
Press (or Press and hold in for one second) the PF key
assigned to “CW ID” to turn the CW Identifier feature
“On” or “Off” (toggle).
The Compander IC contains two variable gain circuits
configured for compressing and expanding the dynamic
range of the repeater’s transmitted and received audio
signal. When you enable this function, the signal-tonoise ratio can be improved by reducing the transmitted audio dynamic range.
VXR-9000 FM REPEATER OPERATING MANUAL
When the CW ID feature is set to “On,” your station’s
callsign will be superimposed on the outbound signal,
in Morse Code, at the beginning of every transmission.
Programming of the callsign is performed by your VERTEX STANDARD dealer.
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
PROGRAMMABLE FUNCTION (PF) KEY DETAILS
TWO TONE DEC
MONITOR
Press (or Press and hold in for one second) the PF key
assigned to “Two Tone Dec” to turn the 2-Tone Decoder
“On” or “Off” (toggle).
Press (or Press and hold in for one second) the PF key
assigned to “Monitor” to cancel CTCSS and DCS squelch
decoding, so as to enable reception of signals present on
the channel that do not contain a matching CTCSS tone
or DCS code.
CW ID SINGLE
Press (or Press and hold in for one second) the PF key
assigned to “CW ID Single” to send the station callsign,
via Morse Code, once. Programming of the callsign is
performed by your VERTEX STANDARD dealer.
MONITOR M
This function provides to “Monitor” to cancel CTCSS
and DCS squelch decoding, so long as the PF key assigned to “Monitor M” is pressed and held in.
CW MESSAGE 1 - CW MESSAGE 8
Press (or press and hold in for one second) the PF key
assigned to “CW Message 1 - 8” to send a pre-programmed Morse Code message on the transmitted signal. Programming of the message(s) is performed by
your VERTEX STANDARD dealer.
MULTI TONE
Press (or Press and hold in for one second) the PF key
assigned to “Multi Tone” to switch the Tone Table between “Main” and “Sub.”
PANEL INDICATOR
DC POWER SAVE
Press (or Press and hold in for one second) the PF key
assigned to “DC Power Save” to turn the DC Power
Save feature “On” or “Off” (toggle).
When DC Power Save feature is set to “ON,” activate
the various power save feature (determined from your
VERTEX STANDARD dealer) while the repeater operates from the Backup Power Source.
Press (or Press and hold in for one second) the PF key
assigned to “Panel Indicator” to turn the Front Panel’s
Illumination “On” or “Off” (toggle).
REMOTE
Press (or Press and hold in for one second) the PF key
assigned to “Remote” to toggle the operating mode between the “Remote” mode and “Local” mode.
Press (or Press and hold in for one second) the PF key
assigned to “Encryption” to turn off the Optional Encryption Unit temporarily.
When the “Remote” mode is selected, the repeater operates according to the control instructions received
from the external device (connected to the ACC jack on
the rear panel). While in the “Local” mode, the repeater
operates from the front panel’s PF keys.
ENCRYPTION CODE
REPEAT
Press (or Press and hold in for one second) the PF key
assigned to “Encryption Code” to select the Encryption
Code (determined from your VERTEX STANDARD
dealer; require the FVP-35 Rolling Code Encryption
Unit).
Press (or Press and hold in for one second) the PF key
assigned to “Repeat” to toggle the operating mode between the “Repeater” mode and “Base Transceiver”
mode.
ENCRYPTION
KEY LOCK
Press (or Press and hold in for one second) the PF key
assigned to “Key Lock” to lock the repeater’s front panel
keys (except “Key Lock” key); this feature can be enabled to prevent repeater settings from being disturbed.
LOCAL PTT
Press (or Press and hold in for one second) the PF key
assigned to “Local PTT” to enable (“On”) or disable
(“Off”) operation using a PTT switch connected to the
front panel’s Microphone Jack.
For normal operation, set this key to the “Repeat” mode.
When the “Base Transceiver” mode is selected, you can
speak into the microphone to use this repeater as a transceiver.
RESET
Press (or Press and hold in for one second) the PF key
assigned to “Reset” to reset (same function as the
POWER switch “off” and “on”) the repeater.
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
PROGRAMMABLE FUNCTION (PF) KEY DETAILS
SCAN
TOT
Press (or Press and hold in for one second) the PF key
assigned to “Scan” to start scanning. To stop scanning,
press (or Press and hold in for one second) this key again.
Press (or press and hold in one second) the PF key assigned to “TOT” to turn the Time-Out Timer feature
“On” or “Off” (toggle).
The scanning feature is used to monitor multiple channels programmed into the repeater.
When the TOT feature is set to “On,” the repeater will
return to the “Receive” mode automatically after a preset time of continuous transmission (determined via
programming by your VERTEX STANDARD dealer).
This function is only activated on the “Base Transceiver” mode.
SQUELCH
Press (or Press and hold in for one second) the PF key
assigned to “Squelch” to override the Squelch action
(CTCSS, DCS, and Noise Squelch), so as to hear any signal present on the operating channel.
TEST TONE
Press (or Press and hold in for one second) the PF key
assigned to “Test Tone” to generate the Test Tone Signal,
as programmed by your VERTEX STANDARD dealer.
Press (or Press and hold in for one second) this key again
to stop the generation of the Test Tone. This is a toggle
function.
Press (or Press and hold in for one second) this key while
press and holding the PTT switch to transmit the Test
Tone Signal, as programmed by your VERTEX STANDARD dealer.
TEST TONE M
This function provides momentary generation of the
above-referenced Test Tone signal, so long as the PF key
assigned to “Test Tone M” is pressed and held in.
Press this key while press and holding the PTT switch
to transmit the Test Tone Signal, as programmed by
your VERTEX STANDARD dealer.
VXR-9000 FM REPEATER OPERATING MANUAL
TRANSMIT
Press (or Press and hold in for one second) the PF key
assigned to “Transmit” to enable (“On”) or disable
(“Off”) the transmission of the VXR-9000.
TX POWER MID
Press (or Press and hold in one second) the PF key assigned to “TX Power Mid”to set the transmitter power
to the “Mid” level.
Press (or press and hold in one second) this key again to
return to the “Original” power level (determined via
programming by your VERTEX STANDARD dealer).
This function is ignored on the channel which is programmed to the transmitter power to the “Mid” or
“Low” level by your VERTEX STANDARD dealer.
TX POWER LOW
Press (or Press and hold in one second) the PF key assigned to “TX Power Low”to set the transmitter power
to the “Low” level.
Press (or press and hold in one second) this key again to
return to “Original” power level (determined via programming by your VERTEX STANDARD dealer).
This function is ignored on the channel which is programmed to the transmitter power to the “Low” level
by your VERTEX STANDARD dealer.
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
REAR PANEL CONNECTORS
TX
BACKUP
BACKUP
MAIN
RX
INPUT
DC 13.6V
EXT
 Backup Power Source Terminals
If available, a backup 13.6 Volt power source, such
as a rechargeable battery, may be connected here.
When the Battery Charge switch (located on the PA
Unit) is set to “ON,” a “trickle” charge current is
present here while the repeater is operating from
the “Main Power Source.”
 Circuit Protection Fuse
Two 15-Amp blade fuses, for the “Main” and
“Backup” power sources, are installed here.
 RX Antenna Jack
This BNC-type coaxial jack accepts the receiver input signal, for connection to the receiving antenna,
or the “RX” jack on the duplexer. The input impedance requirement is 50 Ohms.
 TX Antenna Jack
This N-type coaxial jack provides the transmitter
output signal, for connection to the transmitting
antenna, or the “TX” jack on the duplexer. The output impedance requirement is 50 Ohms.
GND
ACC
 Main Power Source Connector
The primary DC power source should be connected
here. The power requirements are 13.6 V DC at 12
Amps, continuous duty.
 External Speaker Jack
This 3.5-mm, 2-pin jack provides variable audio
output for an external speaker. The audio output
impedance at this jack is 4 to 16 Ohms, and the level
varies according to the setting of the front panel's
VOL knob.
 DSUB 25-pin Accessory Connector
This DB-25F connector allows the repeater to be remote-controlled by an external controller. Analog
I/O signals, such as TX Audio In, Discriminator
Output, RSSI, etc. are available. Moreover, the VXR9000 provides eight ports that can be programmed
for various input or output signals, or for control
functions. Each port may be programmed as to its
function, its status (input or output), and its logic
(for output ports only).
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
DB-25 CONNECTOR PORT
The VXR-9000 repeater is provided with a 25-pin DB25F female connector for interconnections to
accessories.Use a DB-25M 25-pin male connector to connect accessories to the repeater. The pins on the accessory connector are explained in detail as follows:
Pin 5: TX ATT
Pin 1: GND
This output is intended for controlling an external coaxial switching relay. It is an open drain output which
can sink approx. 1.5 A when active. The delay time
which is between the repeater cause to transmit mode
and this port switches to ground can be programmed
by your VERTEX STANDARD dealer.
Chassis ground for all logic levels and power supply
return.
Pin 6: DISC OUT
[POWER SUPPLY]
This pin provides 13.6 Volts, 2.0 A, DC from the repeater
supply. There is a internal 3 A fuse to prevent damage
to the repeater.
[ANALOG OUTPUT] (WIDE-BAND: 0 ~ 3,000 HZ)
Received signals with full system deviation produce
350 mVrms audio at this pin. The output impedance is
600 Ohm, and is extracted before the de-emphasis and
squelch circuitry. Use shielded cable to connect to this
pin, and connect the shield to GND.
Pin 3: TX AF IN
Pin 7: N.C.
[ANALOG TRANSMITTER INPUT] (VOICE BAND: 300 ~ 3,000 HZ)
This pin is audio input. Input impedance is 600 Ohms.
This audio is injected before the splatter filter stage, so
excess signal input levels are clipped.
No connection.
Use shielded cable to connect to this pin, and connect
the shield to GND.
Pin 4: TONE IN
[TRANSMITTER INPUT] (SUB-AUDIBLE BAND: 5 ~ 250 HZ)
This pin is sub-audiable tone input. The input impedance is 600 Ohms, and has a flat response characteristic
(repeater deviation is constant for a given signal level
over the frequency range of 5 ~ 250 Hz). Injecting too
high a voltage here causes over-deviation of CTCSS or
DCS, degrading performance.
Use shielded cable to connect to this pin, connecting the
shield to GND.
Pin 8: RSSI
[ANALOG OUTPUT]
A DC voltage proportional to the strength of the signal
currently being received (Receiver Signal Strength Indicator) is provided on this pin. This low impedance
output is generated by the receiver IF sub-system and
buffered by an internal op-amp. Typical voltages are
graphed as follows:
(DC V)
RSSI Output Voltage
Pin 2: +13.6 V
2.5
2.0
1.5
1.0
0.5
–60
–70
–80
–90
–100
–110
–120 (dBm)
Input Signal Level
Pin 9: COAX. SW
[LOGIC OUTPUT (ACTIVE LOW)]
This output is intended for controlling an external coaxial switching relay. It is an open drain output which
can sink approx. 1.5 A when active. This signal only
switches if the repeater has been programmed for “SIMPLEX” mode. If programmed for “DUPLEX,” the signal
remains open (high impedance) at all time.
DB-25 PIN NUMBERING
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
DB-25 CONNECTOR PORT
Pin 10, 13, 15, 16, 17, 18, 19, 21:
Pin
PROGRAMMABLE I/O “0” ~ ”7”
The VXR-9000 provides eight ports (PIO)
that can be programmed for various
input or output signals, or for control
functions. Each port may be programmed as to its function, its status
(input or output), and its logic (for output ports only).
10
13
15
16
17
18
19
21
Pin 23: RXD HIGH
I/O Port
Pin 11: NSQ DET
This is an open-collector, active-low output capable of
sinking about 10 mA. It indicates that the receiver
squelch is open. If the squelch control is properly set,
this indicates a carrier on the receiver channel.
Pin 12: EXT PTT
This input is internally pulled up to 5 VDC. When pulled
low by an external device, it keys the repeater transmitter while the repeater is operating in the “Remote”
mode. Avoid voltage in excess of 5 V on this pin, or
internal damage to the microprocessor on the repeater
CNTL Unit may result.
[DIGITAL OUTPUT FOR DATA COMMUNICATIONS]
(Max.: 5 kHz)
This pin is an output for high speed receiving data signals (typically 9600 bps), with the data being extracted
immediately after the discriminator (prior to any deemphasis).
Pin 24: TXD LOW
[ANALOG INPUT FOR DATA COMMUNICATIONS]
(300 ~ 3,000 Hz)
This pin is intended to be used as a low speed data
signal input to the repeater (typically 1200 bps). This
digital data signal is injected before the transmitter preemphasis and limiting stages, so excess signal input
levels are clipped.
Pin 25: TXD HIGH
[DIGITAL INPUT FOR THE DATA COMMUNICATIONS]
(0 ~ 5 kHz)
This pin is intended to be used as a high speed digital
data signal input to the repeater (typically 9600 bps).
This digital data signal is injected after the transmitter
splatter filter stage.
Pin 14, 20: GND
Chassis ground for all logic levels and power supply
return.
Pin 22: RXD LOW
[ANALOG OUTPUT FOR DATA COMMUNICATIONS]
(300 ~ 3,000 Hz)
This pin is an output for low speed receiving data signals (typically 1200 bps), with the data being extracted
after the de-emphasis and low pass filter stages.
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
INSTALLATION
Antenna Considerations
Equipment Location
Repeater operation requires two antennas, one for receiving and one for transmitting, so that the receiving
antenna does not absorb energy from the transmitting
antenna. There are a number of ways to do this, depending on the TX/RX frequency separation, and on the
locations available for antenna mounting.
The VXR-9000 must be installed in a 19-inch Mounting
Rack, which will allow for free air flow around the heat
sink on the rear apron at all times. In warm climates,
the repeater should not be sealed in a small, closed room
without air conditioning.
Regardless of the above choice, it is of paramount importance that the antenna(s) be mounted as high and in
the clear as possible, preferably within line-of-sight to
all repeater users. Furthermore, losses in the feedline(s)
must be minimized, so the feedline(s) should be high
quality, and as short as possible. If a long feedline is
necessary, use coaxial “hardline” cable to reduce losses.
Repeater antennas should have an impedance of 50 Ω
at the operating frequency. When separate receive and
transmit antennas are used, high-Q narrow-band types
may serve to minimize interaction.
While the operating temperature range of the VXR-9000
is quite broad, the best location is one in which the air
temperature does not approach the extremes of the
specified range, and one that does not change rapidly.
Protect the VXR-9000 (Mounting Rack) from wind and
rain, and extremes in temperature or humidity that
may shorten the useful life of the equipment. Try to locate the VXR-9000 (Mounting Rack) in an environment
that is also comfortable for service personnel, if possible.
NEVER TRANSMIT WITHOUT HAVING A
TRANSMIT ANTENNA CONNECTED TO THE
TX ANTENNA JACK OF THE REPEATER.
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
INSTALLATION
Power Supply
Backup Power Supply
Operation of the VXR-9000 requires a power source capable of providing at least 12 Amps continuously at
13.6 Volts DC. The FP-1023 (23 A) and FP-1030A (30 A)
AC Power Supplies are available from your Vertex Standard dealer to satisfy these requirements. Other wellregulated power supplies may be used, as well, if they
meet the above voltage and current specifications.
For uninterrupted operation during power failures, a
12-volt rechargeable type battery (55-Ah or more recommended) may be connected to the BACKUP terminal posts on the rear panel. While the repeater is operating from the Main Power Source a slight charging
current will maintain battery charge. In the event of an
unexpected interruption of the Main Power Source, the
automatic power control circuit will automatically
switch the repeater to the backup battery, and operation will not be interrupted.
Use the DC power cable supplied with your repeater
for making power connections to the power supply.
Connect the RED power cable lead to the POSITIVE (+)
power supply terminal, and connect the BLACK power
cable lead to the NEGATIVE (–) power supply terminal.
After prolonged operation from the battery, (Backup
Power Source), it should be disconnected from the repeater and recharged separately before re-connecting,
as the trickle charge is not sufficient for recharging a
completely discharged battery.
Never reapply the Main Power Source to the repeater
with a discharged battery connected as backup, as the
DC startup current can damage the repeater and battery.
BACKUP
B ACK UP
MAIN
Never short the “Backup Power Sorce” Terminals,
when the Battery Charge switch (located on the PA
Unit) is set to “ON.”
 To TX Antenna
 To RX Antenna
While operating from a backup battery, the repeater
requires approximately 7 amperes at 12 Volts during
transmit.
RX
TX
INPUT
DC 13.6V
GND
RED
BLACK
ACC
BLACK
RED
EXT
Supplied DC Power Code
Backup Battery
(12 V, 55 Ah)
TYPICALLY SETUP
10
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
ACCESSORIS & OPTION
Supplied Accessories
DC Power Cord (T9023499) ............................................
15-A Blade Fuse (Q0000075) ...........................................
Knob Cap (RA0506900) ...................................................
Name Plate (RA0508500) ................................................
Operating Manual ...........................................................
Optional Accessories
VXR-9000 FM REPEATER OPERATING MANUAL
FIF-9
FVP-25
FVP-35
MD-11A8J
MH-25A8J
Inline Interface Box
Encryption Unit
Rolling Code Encryption Unit
Desktop Microphone
Hand Microphone
11
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
SPECIFICATIONS
General
Frequency Range:
Number of channel:
PLL Step:
Operating Voltage:
Current Drain:
Frequency Stability:
Operating Temperature Range:
Dimensions (W x H x D):
Weight (Approx.):
Type C : 148 - 174 MHz
32
2.5 kHz/5 kHz/6.25 kHz
13.6V DC ±10 %
30A Maximum
1.5 ppm
1.0 ppm (30min after wake up)
–22 °F to +140 °F (–30 °C to +60 °C)
19 x 3-1/2 x 13-1/2 inch (483 x 88 x 343 mm)
20 kg
Receiver
Antenna Impedance:
Antenna Connector:
Receiver Type:
Sensitivity:
Selectivity:
Intermodulation:
Image Rejection:
Squelch Threshold:
Audio Output:
Audio Distortion:
Hum and Noise:
Audio Frequency Response:
Conducted Spurious:
50 ohm
Type-BNC
Double-Conversion Superheterodyne
0.25 µV (12dB SINAD)
85 dB (Wide), 75 dB (Narrow)
82 dB (Wide), 78 dB (Narrow)
90 dB
–5 dBµ
4 W @4 ohm
<3%
> 55 dB (Wide), > 50 dB (Narrow)
De-emphasis : 6 dB/oct (From 300 Hz to 3 kHz)
< –80 dBm
Transmitter
RF Output Power:
Antenna Impedance:
Antenna Connector:
Modulation Type:
System Deviation:
Hum and Noise:
Microphone Sensitivity:
Audio Frequency Response:
Spurious Emission:
Audio Distortion:
Microphone Impedance:
100/75/50 W (High/Mid/Low)
50 ohm
Type-N
16K0F3E/11K0F3E
±5.0 kHz (Wide), ±2.5 kHz (Narrow)
> 50 dB (Wide), > 45 dB (Narrow)
5 mV
Pre-emphasis : 6dB/oct (From 300 Hz to 3 kHz)
70dB below carrier
3.0 % @1 kHz
600 ohm
Specifications subject to change without notice or obligation.
12
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
Part 15.21: Changes or modifications to this device not expressly approved by Vertex Standard could void the user’s authorization to operate
this device.
VXR-9000 FM REPEATER OPERATING MANUAL
Vertex Standard Co., Ltd.
FCC ID: K6610443250/IC ID: 511B-10443250
Copyright 2005
VERTEX STANDARD CO., LTD.
All rights reserved.
0504s-BE
No portion of this manual may be
reproduced without the permission of
VERTEX STANDARD CO., LTD.
Printed in Japan
Vertex Standard Co., Ltd.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 16
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c2aedc9f-5768-458e-a18c-e9cf23cdaf18
Producer                        : Acrobat Distiller 5.0 (Windows)
Create Date                     : 2005:05:06 08:39:34Z
Modify Date                     : 2005:06:01 21:06:07+09:00
Metadata Date                   : 2005:06:01 21:06:07+09:00
Creator Tool                    : PageMaker 6.5J
Document ID                     : uuid:5358e258-cd4a-49ec-a6dd-23246d1e7d2d
Format                          : application/pdf
Creator                         : manual
Title                           : VXR-9000V-H.p65
Author                          : manual
EXIF Metadata provided by EXIF.tools
FCC ID Filing: K6610443250

Navigation menu