Yaesu Musen 10443250 Rack Mount Repeater User Manual VXR 9000 H PMD

Download:
Mirror Download [FCC.gov]
Document ID	1581279
Application ID	tE4aQ21vO4DvG3WwBSf4+Q==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.64kB (270442 bits)
Date Submitted	2011-11-15 00:00:00
Date Available	2011-11-15 00:00:00
Creation Date	2011-10-31 13:56:51
Producing Software	Acrobat Distiller 9.4.6 (Windows)
Document Lastmod	2011-11-02 11:32:55
Document Title	VXR-9000-H.PMD
Document Creator	PageMaker 7.0J
Document Author:	yohtaki

RACK MOUNT REPEATER
VXR-9000V-H
VXR-9000U-H
OPERATING MANUAL
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
INTRODUCTION
The VXR-9000x-H is commercial-grade 100-watt FM repeater designed to provide reliable two-way full-duplex communications over a wide range of environmental conditions.
Designed to mount in a standard 19-inch rack, the VXR-9000x-H is crafted using the latest computer-aided design
and manufacturing processes, to ensure a high level of reliability to users. Important channel frequency data is stored
in EEPROM, and is easily programmable by a Servicing Technician or Dealer using an IBM compatible personal
computer and the VPL-1 Programming Cable and CE60 Software.
Please take a few minutes to read this manual carefully. The information presented here will allow you to derive
maximum performance from your VXR-9000x-H. After reading it, keep this manual handy for quick reference, in
case questions arise later on.
Important Note: Internal service work, programming, and accessory installations should only be performed by your
authorized Vertex Standard Dealer. Dangerous conditions and/or possibly illegal operation may result from improper setup, programming, or internal modifications.
SAFETY / WARNING INFORMATION
The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures with a
separation distance of at least 1.98 m (VXR-9000V-H) or 1.62 m (VXR-9000U-H) from all persons during
normal operation and must not exceed an antenna gain of 0 dBd. This device must be restricted to work
related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. The antenna(s) used with this device must satisfy the antenna co-location requirements of 47 C.F.R. 1.1307(b)(3).
NOTICE!
 Do not modify this repeater for any reason.
Refer service of this repeater to qualified technicians only.
 When the repeater become abnormal, such as the overheating, smoke smell of burning, etc., turn the main
power switch off and disconnect the Main Power Source connector from the rear of the VXR-9000x-H
immediately. Also disconnect any backup power source you may have connected to the rear of the VXR9000x-H.
 Do not place any combustible material near the repeater.
 Do not spray any liquid over the repeater.
 Ensure that the power and antenna connections are securely made, using cables with excess capacity for
the power being utilized.
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
Page 1
FRONT PANEL CONTROLS & CONNECTORS

 
 



 POWER (O/I) Switch
This is the main power switch for the repeater.
 Power Indicator (MAIN)
This LED glows green when the main power source
is used.
 Power Indicator (BACKUP)
This LED glows red when the backup power source
is used.
 MIC Jack
Connect the microphone plug to this jack. This jack
is also used for writing and reading channel frequency or other configurations via the COM Port of
the PC on which the clone editor (CE60) is running.
 Programmable Function (PF) Key
Six pushbuttons on the front panel are programmable function (PF) keys, each with an orange indicator inside. Each key can be programmed with
two functions, one for a “long” press and one for a
“momentary” press. The PF key functions may be
customized, via programming by your VERTEX
STANDARD dealer, to meet your communications
network requirements. Note that some functions
may require the purchase of optional internal accessories.
 TX Indicator
This LED glows red when the repeater is transmitting.
 Numeric Display
This display consists of two 7-segment LEDs, indicating the channel number during normal operation.
If an abnormal condition arises, an error code will be
displayed:
DISPLAY
DESCRIPTION
01 - 32
PC
UL
HI
SC
LC
E1
E2
E5
E7
E3, E4, E6, E9
Channel Number
Clone Active
PLL Unlock
High temperature in PA Unit
Scan Active
Front Panel Keys are Locked
PTT key is Disabled
Cooling Fan is Disabled
Low Voltage in Backup Battery
PA Unit Abnormality
Contact your Dealer
 BUSY Indicator
This LED glows green when the receiving channel
is busy.
 Speaker
The internal speaker is located here.
 VOL Knob
This control knob adjusts the output level of the front
speaker and external speaker jack on the back panel.
Page 2
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
REAR PANEL CONNECTORS

  
  
 TX Antenna Jack
This N-type coaxial jack provides the transmitter
output signal, for connection to the transmitting antenna, or the “TX” jack on the duplexer. The output
impedance requirement is 50 Ohms.
 Backup Power Source Terminals
If available, a backup 13.6 Volt power source, such
as a rechargeable battery, may be connected here.
When the Battery Charge switch (located on the
100W PA Unit) is set to “ON,” a “trickle” charge
current is present here while the repeater is operating from the “Main Power Source.”
 Circuit Protection Fuse
Two 40-Amp blade fuses, for the “Main” and
“Backup” power sources, are installed here.
 RX Antenna Jack
This BNC-type coaxial jack accepts the receiver input signal, for connection to the receiving antenna,
or the “RX” jack on the duplexer. The input impedance requirement is 50 Ohms.
 Main Power Source Connector
The primary DC power source should be connected
here. The power requirements are 13.6 V DC at 30
Amps, continuous duty.
 External Speaker Jack
This 3.5-mm, 2-pin jack provides variable audio
output for an external speaker. The audio output
impedance at this jack is 4 to 16 Ohms, and the level
varies according to the setting of the front panel's
VOL knob.
 DSUB 25-pin Accessory Connector
This DB-25F connector allows the repeater to be remote-controlled by an external controller. Analog I/
O signals, such as TX Audio In, Discriminator Output, RSSI, etc. are available. Moreover, the VXR9000x-H provides eight ports that can be programmed for various input or output signals, or for
control functions. Each port may be programmed
as to its function, its status (input or output), and its
logic (for output ports only).
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
Page 3
INSTALLATION
Antenna Considerations
Equipment Location
Repeater operation requires two antennas, one for receiving and one for transmitting, so that the receiving
antenna does not absorb energy from the transmitting
antenna. There are a number of ways to do this, depending on the TX/RX frequency separation, and on the locations available for antenna mounting.
The VXR-9000x-H must be installed in a 19-inch Mounting Rack, which will allow for free air flow around the
heat sink of the 100 W PA Unit at all times. In warm
climates, the repeater should not be sealed in a small,
closed room without air conditioning.
Regardless of the above choice, it is of paramount importance that the antenna(s) be mounted as high and in
the clear as possible, preferably within line-of-sight to
all repeater users. Furthermore, losses in the feedline(s)
must be minimized, so the feedline(s) should be high
quality, and as short as possible. If a long feedline is
necessary, use coaxial “hardline” cable to reduce losses.
Repeater antennas should have an impedance of 50 
at the operating frequency. When separate receive and
transmit antennas are used, high-Q narrow-band types
may serve to minimize interaction.
While the operating temperature range of the VXR9000x-H is quite broad, the best location is one in which
the air temperature does not approach the extremes of
the specified range, and one that does not change rapidly.
Protect the VXR-9000x-H (Mounting Rack) from wind
and rain, and extremes in temperature or humidity that
may shorten the useful life of the equipment. Try to locate the VXR-9000x-H (Mounting Rack) in an environment that is also comfortable for service personnel, if
possible.
NEVER TRANSMIT WITHOUT HAVING A
TRANSMIT ANTENNA CONNECTED TO THE
TX ANTENNA JACK OF THE REPEATER.
Page 4
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
INSTALLATION
Power Supply
Backup Power Supply
Operation of the VXR-9000x-H requires a power source
capable of providing at least 30 Amps continuously at
13.6 Volts DC. Please prepare the regulated power supply which satisfies the above voltage and current specifications.
For uninterrupted operation during power failures, a
12-volt rechargeable type battery (55-Ah or more recommended) may be connected to the BACKUP terminal posts on the rear panel. While the repeater is operating from the Main Power Source a slight charging
current will maintain battery charge. In the event of an
unexpected interruption of the Main Power Source, the
automatic power control circuit will automatically
switch the repeater to the backup battery, and operation will not be interrupted.
Use the DC power cable (VXSTD P/N: T9207279) supplied with your repeater for making power connections
to the power supply. Connect the RED power cable lead
to the POSITIVE (+) power supply terminal, and connect the BLACK power cable lead to the NEGATIVE (–
) power supply terminal.
After prolonged operation from the battery, (Backup
Power Source), it should be disconnected from the repeater and recharged separately before re-connecting,
as the trickle charge is not sufficient for recharging a
completely discharged battery.
 To TX Antenna
 To RX Antenna
Never reapply the Main Power Source to the repeater
with a discharged battery connected as backup, as the
DC startup current can damage the repeater and battery.
Never short the “Backup Power Sorce” Terminals,
when the Battery Charge switch (located on the
Relay Unit) is set to “ON.”
BLACK
RED
BLACK
RED
Power Supply
(13.6 V, 40 ~ 50 A)
Supplied DC Power Code
(T9207279)
Backup Battery
(12 V, 55 Ah)
TYPICALLY SETUP
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
Page 5
NOTE
Page 6
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
NOTE
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
Page 7
NOTE
Page 8
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
Part 15.21: Changes or modifications to this device not expressly approved
by Vertex Standard could void the user’s authorization to operate this device.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
Copyright 2011
VERTEX STANDARD CO., LTD.
All rights reserved.
No portion of this manual may be
reproduced without the permission of
VERTEX STANDARD CO., LTD.
Printed in Japan
VXR-9000V-H / VXR-9000U-H FM REPEATER OPERATING MANUAL

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : VXR-9000-H.PMD
Creator                         : yohtaki
Create Date                     : 2011:10:31 13:56:51+09:00
Creator Tool                    : PageMaker 7.0J
Modify Date                     : 2011:11:02 11:32:55+09:00
Metadata Date                   : 2011:11:02 11:32:55+09:00
Producer                        : Acrobat Distiller 9.4.6 (Windows)
Document ID                     : uuid:73593d55-4c5a-4477-ab01-82672b5a1144
Instance ID                     : uuid:b0f0704c-8f74-4d5f-bb98-5574db64dfa5
Page Count                      : 12
Author                          : yohtaki

EXIF Metadata provided by EXIF.tools