Yaesu Musen 10854720 Portable UHF Transceiver User Manual VX 230 pmd

Yaesu Musen Co., Ltd. Portable UHF Transceiver VX 230 pmd

Contents

Users manual 2

Scan SetPress (or press and hold) the assigned Programmable key todelete the Current Memory Channel from the Scanning List. Whenyou delete a channel from the Scanning List, a low tone beep willsound. To restore a particular channel to your Scanning List, press(or press and hold) the assigned Programmable key again; ahigh tone beep will sound.DW (Dual Watch)The Dual Watch feature is similar to the Scan feature, except thatonly two channels are monitored: the current operating channel,and the “Priority” channel.To activate Dual Watch:Press (or Press and hold) the assigned Programmable key.The scanner will search the two channels; it will pause eachtime it finds a channel on which someone is speaking. Whenthe Dual Watch feature is activated, the LED indicator on thetop of the radio will glow green.To stop Dual Watch:Press (or Press and hold) the assigned Programmable key.Operation will revert to the channel to which the CH knob isset.TA ScanPress the assigned programmable key to toggle the TA (TalkAround) scan feature “On” and “Off.”While TA scan is proceeding, the VX-230 will search both thetransmit and receive frequencies (and the LED indicator on the topof the radio will glow green). When a signal is encountered on thereceive frequency, the VX-230 will pause until the signal disap-pears. When a signal is encountered on the transmit frequency, theVX-230 will check for activity on the receive frequency every fewseconds (interval programmed by your Dealer).TA (Talk Around)Press (or Press and hold) the assigned Programmable key toactivate the Talk Around feature when you are operating on duplexchannel systems (separate receive and transmit frequencies, utiliz-ing a “repeater” station). The Talk Around feature allows you tobypass the repeater station and talk directly to a station that is nearby.This feature has no effect when you are operating on “Simplex”channels, where the receive and transmit frequencies are alreadythe same.When the “TA” function is activated, the LED indicator on the topof the radio will glow green.TX Save DisablePress (or Press and hold) the assigned Programmable key todisable the Transmit Battery Saver, if you are operating in a loca-tion where high power is almost always needed.The Transmit Battery Saver helps extend battery life by reducingtransmit power when a very strong signal from an apparently nearbystation is being received. Under some circumstances, though, yourhand-held radio may not be heard well at the other end of the com-munication path, and high power may be necessary at all times.Mon (Monitor)Press (or Press and hold) the assigned Programmable key mo-mentarily to disable the Tone squelch. When disables the Tonesquelch, the LED indicator on the top of the radio will glow green.SQL OffPress (or Press and hold) the assigned Programmable key todisable the Noise and Tone squelch. Again press (or Press and hold)the assigned Programmable key to resume normal (quiet) Noiseand Tone squelch action.SQL SetYou can manually adjust the squelch level using this function. Pressthe assigned Programmable key to toggle the squelch thresholdlevel “High” and “Low”.Low PowerPress (or Press and hold) the assigned Programmable key to setthe radio’s transmitter to the “Low Power” mode, thus extendingbattery life. Press (or Press and hold) the assigned Programmablekey again to return to “High Power” operation when in difficultterrain. When the radio’s transmitter is set to “Low Power” mode,the LED indicator on the top of the radio will glow green.ScanThe Scanning feature is used to monitor multiple channels pro-grammed into the transceiver. While scanning, the radio will checkeach channel for the presence of a signal, and will stop on a chan-nel if a signal is present.To activate scanning:Press (or Press and hold) the assigned Programmable key.The scanner will search the channels, looking for active ones; itwill pause each time it finds a channel on which someone isspeaking. When the scanner is activated, the LED indicator onthe top of the radio will glow green.To stop scanning:Press (or Press and hold) the assigned Programmable key.Operation will revert to the channel to which the CH knob isset.Follow-Me Scan“Follow-Me” Scan feature checks a User-assigned Priority Chan-nel regularly as you scan the other channels. Thus, if only Chan-nels 1, 3, and 5 (of the 8 available channels) are designated for“Scanning,” the user may nonetheless any channel as the “User-assigned” Priority Channel via the “Follow-Me” feature.Press the assigned Programmable key to activate “Follow-Me”scanning, then turn the CH selector knob to the channel which youwant to designate as the “User-Assigned Priority Channel”. Whenthe scanner stops on an “active” channel, the User-assigned Prior-ity Channel will automatically be checked every few seconds (in-terval programmed by your Dealer).DDDDDESCRIPTIONESCRIPTIONESCRIPTIONESCRIPTIONESCRIPTION     OFOFOFOFOF O O O O OPERATINGPERATINGPERATINGPERATINGPERATING F F F F FUNCTIONSUNCTIONSUNCTIONSUNCTIONSUNCTIONSKKKKKEYEYEYEYEY F F F F FUNCTIONSUNCTIONSUNCTIONSUNCTIONSUNCTIONSThe VX-230 provide [Side 1] and [Side 2] keys. These  Pro-grammable  keys functions can be customized (set to other func-tions), via programming by your VERTEX STANDARD dealer,to meet your communications/network requirements. Some fea-tures may require the purchase and installation of optional internalaccessories. The possible Programmable key features are illus-trated below, and their functions are explained in the next chapter.For further details, contact your VERTEX STANDARD dealer.For future reference, check the box next to each function that hasbeen assigned to the Programmable key on your particular ra-dio, and keep it handy.ResetPress (or Press and hold) the assigned Programmable key tosilence the receiver and reset for another call, when a communica-tion is finished.CallPress (or Press and hold) the assigned Programmable key tosend a programmed 2-Tone sequential tone.Speed DialYour Dealer may have a pre-programmed Auto-Dial telephone num-ber memory into your radio. Press (or Press and hold) the assignedProgrammable key to send the pre-programmed Auto-Dial tele-phone number. The DTMF tones sent during the dialing sequencewill be heard in the speaker.LockPress (or Press and hold) the assigned Programmable key tolock the CH knob, Programmable keys, and PTT switch. Theprecise lockout configuration is programmed by your VERTEXSTANDARD dealer.EmergencyThe VX-230 series includes an “Emergency” feature, which maybe useful, if you have someone monitoring on the same frequencyas your transceiver’s channel. For further details contact yourVERTEX STANDARD dealer.Lone WorkerPress and hold the assigned Programmable key to toggle theLone Worker feature “ON” and “OFF.”The Lone Worker feature will emit an audible alarm for 30 sec-onds at one second intervals when the Lone Worker Timer hasexpired. If the user does not reset the timer by pressing the PTTswitch, the radio switches to the Emergency mode.FUNCTIONNoneMon (Monitor)SQL OffSQL SetLow PowerScanFollw-Me ScanScan SetDW (Dual Watch)TA ScanTA (Talk Around)TX Save DisableResetCallSpeed DialLockEmergencyLone Worker[Side 1]////////////////-- /---- /--PROGRAMMABLE KEY (PRESS / PRESS AND HOLD)[Side 2]////////////////-- /---- /--AAAAACCESSORIESCCESSORIESCCESSORIESCCESSORIESCCESSORIES & O & O & O & O & OPTIONSPTIONSPTIONSPTIONSPTIONSFNB-V103LI 7.4 V 1150 mAh Lithium-Ion BatteryFNB-V104LI 7.4 V 2000 mAh Lithium-Ion BatteryVAC-300 Desktop Rapid ChargerVAC-6300 6-unit Multi ChargerPA-42 AC Adapter (for VAC-300)MH-37A4B Earpiece/MicrophoneMH-45B4B Speaker/MicrophoneMH-360S Speaker/MicrophoneMH-450S Speaker/MicrophoneVC-25 VOX HeadsetVCM-2 Vehicle Charger Mount Adapter (for VAC-300)DCM-1 Desktop Charger Bracket (for VAC-300)ATV-8A Rubber Antenna 134-151 MHzATV-8B Rubber Antenna 150-163 MHzATV-8C Rubber Antenna 161-174 MHzATV-6XL Rubber Antenna 134-174 MHz (Untuned)ATU-6A Rubber Antenna 400-430 MHzATU-6B Rubber Antenna 420-450 MHzATU-6C Rubber Antenna 440-470 MHzATU-6D Rubber Antenna 450-485 MHzATU-6F Rubber Antenna 485-520 MHzCLIP-18 Belt ClipLCC-230 Leather CaseCE99 Programming SoftwareFIF-10A USB Programming InterfaceCT-27 Radio to Radio Programming CableCT-42A PC Programming CableCT-106 PC Programming Cable (for FIF-10A)ARTS ARTS ARTS ARTS ARTS (AAAAAUTOUTOUTOUTOUTO R R R R RANGEANGEANGEANGEANGE T T T T TRANSPONDRANSPONDRANSPONDRANSPONDRANSPOND S S S S SYSTEMYSTEMYSTEMYSTEMYSTEM)This system is designed to inform you when you and anotherARTS-equipped station are within communication range.During ARTS operation, your radio automatically transmits forabout 1 second every 55 seconds in an attempt to shake hands withthe other station.If you are out of range for more than two minutes, your radio sensesthat no signal has been received, a ringing beeper will sound. Ifyou subsequently move back into range, as soon as the other sta-tion transmits, your beeper will sound.FCC ID:K6610854720IC: 511B-10854720Vertex Standard Co.,Ltd.

Navigation menu