Yaesu Musen 30173X3D Marine Transceiver User Manual GX1500S p65
Yaesu Musen Co., Ltd. Marine Transceiver GX1500S p65
UserManual.wiki
>
Yaesu Musen
>
30173X3D User Manual
OPERATING MANUAL
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![GX1500SPage 128.4 CONNECTION OF GPS WITH NMEA OUTPUT• The GPS must have the NMEA Output turned on and set to 4800 Baud inthe setup menu. If there is a selection for parity select none.• For further information on interfacing /setting up your GPS. Please contactthe manufacturer of the GPS receiver.•GX1500S can read NMEA-0183 version 2.0 or higher.• The NMEA supported sentences are:Input: GLL, GGA, RMC and GNS (RMC sentence is recommended)Output: DSC and DSE(DSC sentences to Standard Horizon Plotter for Position Polling)If you have further inquires, please feel free to contact Product Support at:Phone: (800) 767-2450Email: marinetech@vxstdusa.com8.5 CHECKING GPS CONNECTIONSAfter connections have been made between the GX1500S and the GPS, asmall satellite icon will appear on the top right corner ofthe LCD display. To see the additional GPS information,press and hold the [H/L(NAV)] key. The GX1500S showsthe Date, Time, SOG and COG.Manufacturer/ModelLowrance PortableMagellan Fixed MountMagellan PortableNorthstarRaytheon 420Raytheon 520 / 620Raytheon RL SERIESSimradSitex Neptune, NautilusWiresOrangeBlack (GND)GrayBlack (GND)OrangeBlack (GND)YellowBlack (GND)YellowBrownBlueBrownWhiteBrownWhiteBrownGrayBrownGX3500SBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenWiresGreenBlueBrownWhiteBlueWhiteBlackBlueBlack (GND)BrownBlack (GND)YellowGreenGreenBlackWhiteBlackWhiteBlack (GND)Manufacturer/ModelSTANDARD HORIZONFuruno GP30, 36Furuno GP1650, 1850Garmin Fixed MountsGarmin PortablesJRC GPS500JRC 100 SERIESJRC 200 SERIESLowrance Fixed MountGX3500SGreenGrayBlueBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenBlueGreenFCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-12.png)
![Page 13GX1500S8.6 CHANGING THE GPS TIMEFrom the Factory the GX1500S shows GPS satellite time or UTC time. A timeoffset is needed to show the local time in your area.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Time Set” with theCHANNEL selector knob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select time off-set from UTC. See illustration below to find your off-set time from UTC. If “0:00” is assigned, the time isthe same as UTC (Universal Time Coordinated orGMT Greenwich Mean Time).5. Press the [ENT] key to store the time offset.6. Press the [16/9] key or turn the CHANNEL selector knob to select “Exit,”then press the [ENT] key to return to the “Radio Setup” menu, select “Exit”and press the [ENT] key to return to radio operation.OFFSET TIME TABLEFCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-13.png)
![GX1500SPage 148.8 CHANGING COG TO TRUE OR MAGNETICAllows customizing the NAV data showing GPS Course Over Ground (COG).Factory default is True however following the steps below the COG can bechanged to Magnetic.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Magnetic” with theCHANNEL selector knob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “On” (rep-resenting “Magnetic”) or “Off” (representing “True”).5. Press the [ENT] key to store the selected setting.6. Turn the CHANNEL selector knob to select “Exit,”then press the [ENT] key to return to the “RadioSetup” menu, select “Exit” and press the [ENT] keyto return to radio operation.8.7 CHANGING THE TIME LOCATIONYou may select the time display between local time and UTC (time GPS sendsto radio). Time is displayed when GPS position (LAT/LON) is displayed by press-ing the [F] key followed by the [6(NAV)] key.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Time Disp” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “UTC” or“Local.”5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.In the local time mode, the display shows the time by the 12-hour system.Meanwhile, the display shows the time by the 24-hour system in the UTC mode.(“UTC” mode)(“LOCAL” mode)FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-14.png)
![Page 17GX1500SRemote Mic or External Speaker SelectionBy default the RAM+ (or VH-310 Handset) internal speaker is turned on, how-ever using the RAM+ mic (or VH-310 Handset) this speaker can be turned offso the external speaker can be used.RAM+ mic procedure1. Press and hold the [CALL/SET] key.2. Press the [] or [] key to select “RADIO SETUP.”3. Press the [CALL/SET] key.4. Press the [] key to until “EXT SPK” is shown and press the[CALL/SET] key.5. Press the [] or [] key to select “oF” (External speakeroff) or “on” (External speaker on).6. Press the [CALL/SET] key to save the selection.7. Press the [16/9] key to exit this mode.VH-310 Procedure1. Press and hold the [CALL(MENU)] key.2. Press the [] or [] key to select “RADIO SETUP.”3. Press the [ENT] key4. Press the [] key to until “EXT SPK” is shown and press the[ENT] key.5. Press the [] or [] key to select “oF” (External speakeroff) or “on” (External speaker on).6. Press the [ENT] key to save the selection.7. Press the [16/9] key to exit this mode.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-17.png)
![GX1500SPage 189 CONTROLS AND INDICATORSNOTEThis section defines each control of the transceiver. See Figure 4 forlocation of controls. For detailed operating instructions refer to section“10 BASIC OPERATION.”CHANNEL SELECTOR KNOBRotary knob used to select channels and to choose menu items (such as theDSC menu, radio setup menu, and DSC setup menu). The [UP()] /[DOWN()] keys on the microphone can also be used to select channels andmenu items.Secondary UseWhile holding down the [SCAN] key and turning the CHANNEL selectorknob, you can confirm memory channels for scanning.[WX] KeyImmediately recalls the previously selected NOAA weather channel fromany channel.Secondary useHolding down the [16/9] key while pressing the [WX] key changes the Chan-nel Group.[16/9] KeyImmediately recalls channel 16 from any channel location. Holding downthis key recalls channel 9. Pressing the [16/9] key again reverts to the pre-vious selected working channel.Secondary usePress and hold the [16/9] key then press the [WX] key to switch the Chan-nel Group.POWER SWITCH / VOLUME CONTROL (VOL/PWR)Turns the transceiver on and off as well as adjusts the audio volume.Press and hold this knob for one second to turn the radio on. Clockwiserotation of this knob increases the audio volume level.Press and hold this knob for two seconds to turn the radio off.SQUELCH CONTROL (SQL)Adjusting this control clockwise, sets the point at which random noise onthe channel does not activate the audio circuits but a received signal does.This point is called the squelch threshold. Further adjustment of the squelchcontrol will degrade reception of wanted transmissions.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-18.png)
![GX1500SPage 20KEYPAD[SCAN(MEM)] KeyPress this key to start and stop the scanning of programmed channels.Refer to section “10.12 SCANNING” for details.Secondary usePress and hold this key, memorize the selected channel into the trans-ceiver scan memory for scanning.When repeat the same procedures (press and hold this key), DELETESthe channel from the scan memory. Refer to section “10.12 SCANNING”for details.[DW/IC)] KeyPress this key to start the scanning for voice communications on thepriority channel and another selected channel until a signal is receivedon either channel (Dual Watch). Refer to section “10.11 DUAL WATCH(TO PRIORITY CHANNEL)” for details.Secondary usePress and hold this key, when the optional RAM+ Mic or VH-310 Handsetis connected, intercom operation will operate between radio and RAM+Mic. Refer to section “10.14 INTERCOM OPERATION” for details.[H/L(NAV)] KeyPress this key to toggle the transmit output power between 25 W (High)and 1 W (Low) power. When the [H/L(NAV)] key is pressed while thetransceiver is on channel 13 or 67, the power will temporarily switch fromLO to HI power until the PTT is released.The [H/L(NAV)] key does not function on transmit inhibited and low poweronly channels.Secondary usePress and hold this key, the LCD displays NAV GPS Data, Time, SOG(Speed Over Ground), and COG (Course Over Ground) when a GPS isconnected to the accessory cable of the GX1500S. See section “8.4CONNECTION OF GPS WITH NMEA OUTPUT” for details.[CALL(MENU)] KeyPress the [CALL(MENU)] key to access the DSC OPERATION menu.The “INDIVIDUAL CALL,” “GROUP CALL,” and “ALL SHIPS CALL” func-tions can be accessed from the DSC OPERATION menu.Secondary usePress and hold the [CALL(MENU)] key to access the “Radio Setup”(refer to section “12 RADIO SETUP MODE”) or “DSC Setup” menu (re-fer to section “11 DIGITAL SELECTIVE CALLING”).FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-20.png)
![Page 21GX1500S[ENT] KeyPress the [ENT] Key to determine the menu selection and/or keypadentry.[CLR] KeyPress the [CLR] Key to cancel the menu selection and/or keypad entry.[DISTRESS] KeyUsed to send a DSC Distress Call. To send the distress call refer to section“11.3.1 (Transmitting A DSC Distress Call).”ACCESSORY CONNECTION CABLEConnects the GX1500S to a GPS, a PA speaker, and an external speaker.DC INPUT CABLEConnects the radio to a DC power supply capable of delivering 12V DC.REMOTE MIC CONNECTORSConnects the GX1500S to the enhanced RAM+ MIC (Remote Access Mi-crophone) or the VH-310 Handset. Refer to section “13 ENHANCED RAM+MIC OPERATION” or “14 VH-310 HEADSET OPERATION” for details.ANTENNA JACKConnects an antenna to the transceiver. Use a marine VHF antenna withan impedance of 50 ohms.PTT (Push-To-Talk) SWITCHKeys the transmitter when the transceiver is in radio mode. If the transceiveris in the intercom operation mode (between the RAM+ (or VH-310 Headset)and the GX1500S), or PA mode, it activates the GX1500S microphone forvoice communications.MICROPHONETransmits the voice message with reduction of background noise, usingClear Voice Noise Reduction Technology.[UP()] / [DOWN()] KEYSThe [UP()] and [DOWN()] on the microphone function the same as theCHANNEL selector knob on the front panel of the transceiver.[16/9] KeyThe [16/9] key on the microphone function the same as the [16/9] key onthe front panel of the transceiver.Immediately recalls channel 16 from any channel location. Holding downthis key recalls channel 9. Pressing the [16/9] key again reverts to the pre-vious selected working channel.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-21.png)
![Page 23GX1500S10.4 SIMPLEX/DUPLEX CHANNEL USERefer to the VHF MARINE CHANNEL CHART (page 81) for instructions on useof simplex and duplex channels.NOTEAll channels are factory-programmed in accordance with International,Industry Canada (Canada), and FCC (USA) regulations. Mode of opera-tion cannot be altered from simplex to duplex or vice-versa.10.5 INTERNATIONAL, USA, AND CANADA MODE1. To change the modes, hold the [16/9] key and press the [WX] key. Themode changes from International to Canadian to USA with each press ofthe [WX] key.2. “INTL” will be displayed for International mode, and “CAN” will be displayedfor Canadian mode, and “USA” will be displayed on the LCD for USA mode.3. Refer to the VHF MARINE CHANNEL CHART (page 81) for allocated chan-nels in each mode.10.6 NOAA WEATHER CHANNELSNOTENOAA Weather channels are available in the waters of USA and Canada only.1. To receive a NOAA weather channel, press the [WX] key from any channel.The transceiver will go to the last selected weather channel.2. Turn the CHANNEL selector knob on the radio or [UP()] / [DOWN()]keys on the microphone to select a different NOAA weather channel.3. To exit from the NOAA weather channels, press the [WX] key. The trans-ceiver returns to the channel it was on prior to a weather channel.10.6.1 NOAA Weather AlertIn the event of extreme weather disturbances, such as storms and hurricanes,the NOAA (National Oceanic and Atmospheric Administration) sends a weatheralert accompanied by a 1050 Hz tone and subsequent weather report on one ofthe NOAA weather channels. When the Weather Alert feature is enabled (seesection “12.9 WX ALERT”), the transceiver is capable of receiving this alert ifthe following is performed:1. Program NOAA weather channels into the transceiver’s memory for scan-ning. Follow the same procedure as for regular channels under section “10.12SCANNING.”2. Press the [SCAN] key once to start memory scanning or priority scanning(determined from the “Radio Setup” selection, see page 54 for details).FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-23.png)
![GX1500SPage 243. The programmed NOAA weather channels will be scanned along with theregular-programmed channels. However, scanning will not stop on a nor-mal weather broadcast unless a NOAA alert is received.4. When an alert is received on a NOAA weather channel, scanning will stop andthe transceiver will emit a loud beep to alert the user of a NOAA broadcast.5. Press the [WX] key to stop the alert tone and receive the weather report.NOTEIf the [WX] key is not pressed the alert tone will be emitted for 5 minutesand then the weather report will be received.NOTEThe Weather Alert feature is also engaged while the transceiver is re-ceiving on one of the NOAA weather channels.10.6.2 NOAA Weather Alert TestingNOAA tests the alert system ever Wednesday between 11AM and 1PM. To testthe GX1500S’s NOAA Weather feature, on Wednesday between 11AM and1PM, setup as in previous section and confirm the alert is heard.10.7 EMERGENCY (CHANNEL 16 USE)Channel 16 is known as the Hail and Distress Channel. An emergency is de-fined as a threat to life or property. In such instances, be sure the transceiver ison and set to CHANNEL 16. Then use the following procedure:1. Press the microphone push-to-talk switch and say “Mayday, Mayday, May-day. This is , , ” (your vessel’s name).2. Then repeat once: “Mayday, ” (your vessel’s name).3. Now report your position in latitude/longitude, or by giving a true or mag-netic bearing (state which) to a well-known landmark such as a navigationaid or geographic feature such as an island or harbor entry.4. Explain the nature of your distress (sinking, collision, aground, fire, heartattack, life-threatening injury, etc.).5. State the kind of assistance your desire (pumps, medical aid, etc.).6. Report the number of persons aboard and condition of any injured.7. Estimate the present seaworthiness and condition of your vessel.8. Give your vessel’s description: length, design (power or sail), color and otherdistinguishing marks. The total transmission should not exceed 1 minute.9. End the message by saying “OVER.” Release the microphone button andlisten.10. If there is no answer, repeat the above procedure. If there is still no re-sponse, try another channel.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-24.png)
![GX1500SPage 26the marine operator and identify yourself by your vessel’s name, The marineoperator will then ask you how you will pay for the call (telephone credit card,collect, etc.) and then link your radio transmission to the telephone lines.The marine telephone company managing the VHF channel you are using maycharge a link-up fee in addition to the cost of the call.10.10 OPERATING ON CHANNELS 13 AND 67Channel 13 is used at docks and bridges and by vessels maneuvering in port.Messages on this channel must concern navigation only, such as meeting andpassing in restricted waters.Channel 67 is used for navigational traffic between vessels.By regulation, power is normally limited to 1 Watt on these channels. Your radiois programmed to automatically reduce power to this limit on these channels.However, in certain situations it may be necessary to temporarily use a higherpower. See page 20 ([H/L(NAV)] key) for means to temporarily override thelow-power limit on these two channels.10.11 DUAL WATCH (TO PRIORITY CHANNEL)Dual watch allows the radio to monitor one channel and the assigned Prioritychannel. By default the priority channel is set to 16, however the priority chan-nel may be changed by referring to section “12.6 PRIORITY CHANNEL SET.”1. Adjust the SQL knob until the background noise disappears.2. Select the channel you wish to dual watch to “Priority channel.”3. Press the [DW(IC)] key.The display will scan between Priority channel andthe channel that was selected in step 2.If a transmission is received on the channel selectedin step 2, the GX1500S will dual watch between the working channel andthe Priority channel.4. To stop Dual Watch, press the [DW(IC)] key again.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-26.png)
![Page 27GX1500S10.12 SCANNINGAllows the user to select the scan type from Memory scan or Priority scan.“Memory scan” scans the channels that were programmed into memory. “Pri-ority scan” scans the channels programmed in memory with the priority chan-nel.10.12.1 Selecting the Scan Type1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “SCAN Type” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “Prior-ity” or “Memory.”5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.10.12.2 Memory Scanning (M-SCAN)1. Adjust the SQL knob until background noise disappears.2. Select a desired channel to be scanned using theCHANNEL selector knob. Press and hold the[SCAN(MEM)] key for one second, “MEM” will ap-pear on the LCD which indicates the channel hasbeen programmed into the transceivers memory.3. Repeat step 2 for all the desired channels to be scanned.4. To DELETE a channel from the transceiver’s memory, select the channelthen press and hold the [SCAN(MEM)] key for one second, “MEM” willdisappear in the LCD.5. To start scanning, just press the [SCAN(MEM)] keymomentarily. “M-SCAN” appears on the LCD. Scan-ning will proceed from the lowest to the highest pro-grammed channel number and will stop on a chan-nel when a transmission is received.6. The channel number will blink during reception.7. To stop scanning, press the [16/9], [WX], [CALL(MENU)], or PTT key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-27.png)
![GX1500SPage 2810.12.3 Priority Scanning (P-SCAN)In the default setting, Channel 16 is set as the priority channel. You may changethe priority channel to the desired channel from the Channel 16 by the RadioSetup Mode, refer to section “12.6 PRIORITY CHANNEL SET.”1. Adjust the SQL knob until background noise disappears.2. Select a desired channel to be scanned using theCHANNEL selector knob. Press and hold the[SCAN(MEM)] key for one second, “MEM” will ap-pear on the LCD which indicates the channel hasbeen programmed into the transceivers memory.3. Repeat step 2 for all the desired channels to be scanned.4. To DELETE a channel from the transceiver’s memory, select the channelthen press and hold the [SCAN(MEM)] key for one second, “MEM” willdisappear in the LCD.5. To start priority scanning, just press the[SCAN(MEM)] key momentarily. “P-SCAN” appearson the LCD. Scanning will proceed between thememorized channels and the priority channel. CH 16the priority channel will be scanned after each programmed channel.6. To stop scanning, press the [16/9], [WX], [CALL(MENU)], or PTT key.You may change the scan resume time by the Radio Setup Mode, refer tosection “12.8 SCAN RESUME TIME.”10.13 NAVIGATION INDICATIONThe transceiver has the ability to display Date, Time, SOG, COG, as well as theposition (LAT/LON), when connected to a GPS receiver.1. Press and hold the [H/L(NAV)] key, display the posi-tion information on the LCD. If the GPS receiver isnot receiving a fix, the display will be as shown in theillustration on the right.2. To hide the position information, press and hold the[H/L(NAV)] key again.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-28.png)
![Page 29GX1500S10.14 INTERCOM OPERATIONIf the RAM+ Mic is connected to the GX1500S, you may communicate betweenthe GX1500S and CMP25 RAM+ Microphones or VH-310 Handset. (Refer tosection “13.2 INTERCOM OPERATION” for CMP25 RAM+ Microphone, “14.2INTERCOM OPERATION” for CMP25 RAM+ Microphone).10.14.1 Communication1. Press and hold the [H/L(IC)] key, the mode is changed to “INTERCOM”mode.2. When the “INTERCOM” operation is activated, “In-tercom” is displayed on the GX1500S, and “IC” isdisplayed on the RAM+ Mic (or VH-310 Handset).3. Press the PTT switch. “Talk” will be shown on thedisplay.NOTE: A warning beep will be emittedwhen the GX1500S microphone’s PTTswitch is pressed while the RAM+ Mic’s(or VH-310 Handset’s) PTT switch ispressed.4. Speak slowly and clearly into the mi-crophone, hold the microphone about1/2 inch away from your mouth.5. When finished, release the PTT switch.6. To exit the “INTERCOM” mode and return to radio operation mode, pressthe [16/9] or [CLR] key.10.14.2 CallingPress and hold the [H/L(IC)] key for one second when the “INTERCOM” opera-tion is activated, a calling beep is emitted from the transceiver speaker.(RAM+ Mic’s PTT switch is pressed)(GX3500S’s PTT switch is pressed)FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-29.png)
![Page 31GX1500S11.2 MARITIME MOBILE SERVICE IDENTITY (MMSI)11.2.1 What is an MMSI?An MMSI is a nine digit number used on Marine Transceivers capable of usingDigital Selective Calling (DSC). This number is used like a telephone number toselectively call other vessels.THIS NUMBER MUST BE PROGRAMMED INTO THE RADIO TO OPERATETHE GX1500S DSC FUCTIONS.How can I obtain an MMSI assignment?Boat US offers online registration of a MMSI. Visit www.boatus.com/mmsi11.2.2 Programming the MMSIWARNINGUser MMSI can be input only twice. If the user tries to input an MMSImore than twice, the radio will show the display onthe right. If the user needs to change the MMSImore than twice, the transceiver will have to besent to Factory Service. Refer to the section “15.2.FACTORY SERVICE.”1. Press and hold down the [CALL(MENU)] key untilthe “Radio Setup” menu appears.2. Turn the CHANNEL selector knob to the left to se-lect “DSC Setup” menu.3. Press the [ENT] key, then select “User MMSI” withthe CHANNEL selector knob.4. Press the [ENT] key. The “User MMSI” number willappear, and the first digit will be flashing.5. Turn the CHANNEL selector knob or press the[UP()] / [DOWN()] key on the microphone to se-lect the first number of your MMSI, then press the[ENT] key to step to the next number.6. Repeat step 5 to set your MMSI (up to nine digits).6. When finished programming the number, press andhold the [ENT] key to store the number in memory.7. To exit this menu and return to radio operation modepress the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-31.png)
![GX1500SPage 3211.3 DSC DISTRESS CALLThe GX1500S is capable of transmitting and receiving DSC Distress messagesto all DSC radios. The GX1500S may be connected to a GPS to also transmitthe Latitude, Longitude of the vessel.11.3.1 Transmitting a DSC Distress CallNOTETo be able to transmit a DSC distress call an MMSI number must beprogrammed, refer to section “11.2.2 Programming the MMSI.”In order for your ships location to be transmitted a GPS must be connected tothe GX1500S, refer to section “8.4 CONNECTION OF GPS WITH NMEA OUT-PUT.”1. Lift the red spring loaded DISTRESS cover and press the [DISTRESS] key.The “DISTRESS” menu will appear on the LCD.2. Press and hold the [DISTRESS] key. The radios dis-play will count down (5-4-3-2-1) and then transmitthe Distress call.3. When the distress signal is sent, CH70 and “ ”icon will appear on the LCD. After the message hasbeen sent, the radio will sound a Distress Alarm.4. The transceiver will watch for a DSC acknowledg-ment transmission on CH70 and also receive callson CH16.5. If an acknowledgement is received, select channel16 and advise your distress situation.6. If no acknowledgment is received, the distress call isrepeated in 4 minute intervals until a DSC acknowl-edgment is received.7. When a DSC Distress acknowledgment is received,a distress alarm sounds and channel 16 is automati-cally selected. The LCD shows the MMSI of the shipresponding to your distress.RECEIVED ACK: acknowledgment signal is received.RECEIVED RLY: relay signal is received from another vessel or coast station.8. To cancel the DSC distress alarm signal from the speaker, press any key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-32.png)
![Page 33GX1500STransmitting a DSC Distress Call with Nature of DistressThe GX1500S is capable of transmitting a DSC Distress Call with the following“Nature of Distress” categories:Undesignated, Fire, Flooding, Collision, Grounding, Capsizing, Sinking,Adrift, Abandoning, Piracy, Mob1. Lift the red spring loaded DISTRESS cover and press the [DISTRESS] key.The “DISTRESS” menu will appear on the LCD.2. Turn the CHANNEL selector knob to select the de-sired nature of distress category.3. Press and hold the [DISTRESS] key. The radios dis-play will count down (5-4-3-2-1) and then transmitthe Distress call.4. When the distress signal is sent, CH70 and “ ”icon will appear on the LCD. After the message hasbeen sent, the radio will sound a Distress Alarm.5. The transceiver will watch for a DSC acknowledg-ment transmission on CH70 and also receive callson CH16.6. If an acknowledgement is received, select channel16 and advise your distress situation.7. If no acknowledgment is received, the distress call isrepeated in 4 minute intervals until a DSC acknowl-edgment is received.8. When a DSC Distress acknowledgment is received,a distress alarm sounds and channel 16 is automati-cally selected. The LCD shows the MMSI of the shipresponding to your distress.RECEIVED ACK: acknowledgment signal is received.RECEIVED RLY: relay signal is received from another vessel or coast station.9. To cancel the DSC distress alarm signal from the speaker, press any key.Cancel a DSC Distress CallIf a DSC Distress call was sent by error the GX1500Sallows you to send a message to other vessels to cancelthe Distress Call that was made in error.Press the [CLR] key, then press the [ENT] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-33.png)
![Page 35GX1500S11.4.1 Transmitting an All Ships Call1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear.2. Turn the CHANNEL selector knob to select “All Ships.”3. Press the [ENT] key. (To cancel, turn the CHANNELselector knob to select “Exit.”)4. Turn the CHANNEL selector knob to select the call(“Urgency” or “Safety”).5. Press the [ENT] key to transmit the selected type ofall ships DSC call.6. After the ALL SHIPS CALL is transmitted, the trans-ceiver will switch to CH16.7. Listen to the channel to make sure it is not busy, thenkey the microphone and say PAN PAN PAN or“Securite, Securite, Securite” depending on the pri-ority of the call. Say your call sign and announce thechannel you wish to switch to for communications.11.4.2 Receiving an All Ships Call1. When an all ships call is received, an emergencyalarm sounds.The radio will automatically change to channel 16.2. Press any key to stop the alarm.3. Turn the CHANNEL selector knob to see the MMSIof the vessel transmitting the All Ships Call.4. Monitor channel 16 or traffic channel until the UR-GENCY voice communication is completed.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-35.png)
![GX1500SPage 3611.5 INDIVIDUAL CALLThis feature allows the GX1500S to contact another vessel with a DSC VHFradio and automatically switch the receiving radio to a desired communicationschannel. This feature is similar to calling a vessel on CH16 and requesting togo to another channel (switching to the channel is private between the twostations).11.5.1 Setting up the Individual / Position Call DirectoryThe GX1500S has a DSC directory that allows you to store a vessel or person’sname and the MMSI number associated with vessels you wish to transmit Indi-vidual calls, Position Requests and Position Send transmissions.To transmit an Individual call you must program this directory with informationof the persons you wish to call, similar to a cellular phones telephone directory.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “INDIV DIR” with theCHANNEL selector knob.4. Press the [ENT] key, then select “Add” with the CHAN-NEL selector knob.5. Press the [ENT] key.6. Turn the CHANNEL selector knob to scroll throughthe first letter of the name of the vessel or personyou want to reference in the directory.7. Press the [ENT] key to store the first letter in the nameand step to the next letter to the right.8. Repeat step 6 and 7 until the name is complete. Thename can consist of up to eleven characters, if youdo not use all eleven characters press the [ENT] keyto move to the next space. This method can also beused to enter a blank space in the name. To clear theprevious letter, press the [CLR] key.9. After the eleventh letter or space has been entered,press and hold the [CALL(MENU)] key to advance to the MMSI (MaritimeMobile Service Identity Number) number entry.10. Turn the CHANNEL selector knob to scroll through numbers, 0-9. To enterthe desired number and move one space to the right press the [ENT] key.Repeat this procedure until all nine space of the MMSI number are entered.11. If a mistake was made entering in the name or the MMSI number repeatFCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-36.png)
![Page 37GX1500Spressing the [H/L(NAV)] key until the wrong character is selected, then movethe channel knob to correct the entry.12. To store the data entered, press and hold the [ENT] key.13. To enter another individual address, repeat steps 4through 12.14. To exit this menu and return to radio operation modepress the [16/9] key.NOTESelecting “Next” or “Exit” will automatically save the name and MMSInumber into memory.11.5.2 Setting up Individual ReplyAllows setting up the radio to automatically (default setting) or manually re-spond to a DSC Individual call requesting you to switch to a working channel forvoice communications. When Manual is selected the MMSI of the calling ves-sel is shown allowing you to see who is calling. This function is similar to callerid on a cellular phone.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “INDIV Reply” withthe CHANNEL selector knob.4. Press the [ENT]key.5. Turn the CHANNEL selector knob to select “Auto”or “Manual.”6. Press the [ENT] key to store the selected setting.7. To exit this menu and return to radio operation modepress the [16/9] key.11.5.3 Setting up the Individual/Group CallFCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-37.png)
![GX1500SPage 38RingerWhen a Individual Call or Group Call is received the radio will produce a ringingtone for 3 minutes. This selection allows the Individual Call ringer time to bechanged.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appear.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “INDIV Ring” withthe CHANNEL selector knob.4. Press the [ENT] key.5. Turn the CHANNEL selector knob to select ringingtime of a Individual Call.6. Press the [ENT] key to store the selected setting.7. To exit this menu and return to radio operation modepress the [16/9] key.The GX1500S has the capability to turn off the Individual call ringer.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appear.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “DSC Beep” with theCHANNEL selector knob.4. Press the [ENT] key.5. Turn the CHANNEL selector knob to select “Individual”if you wish to disable the Individual Call ringer, or“Group” if you wish to disable the Group Call ringerand press the [ENT] key.6. Turn the CHANNEL selector knob to select “Off.”7. Press the [ENT] key to store the selected setting.8. To exit this menu and return to radio operation modepress the [16/9] key.If you wish to return to enabling the ringer tone, just re-peat the above procedure, turning the CHANNEL selec-tor knob to select “On” in step “6” above.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-38.png)
![Page 39GX1500S11.5.4 Transmitting an Individual CallThis feature allows the user to contact another vessel with a DSC radio. Thisfeature is similar to calling a vessel on CH16 and requesting to go to anotherchannel.Pre-Programmable Calling1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear.2. Turn the CHANNEL selector knob to select “Indi-vidual.” (To cancel, select “Exit” with the CHANNELselector knob or press the [16/9] key.)3. Press the [ENT] key. The transceiver will beep, andthe “Individual directory” will appear.4. Turn the CHANNEL selector knob to select the “Indi-vidual” you want to contact.5. Press the [ENT] key, then turn the CHANNEL selec-tor knob to select the operating channel you want tocommunicate on and press the [ENT] key.6. Press the [ENT] key again to transmit the individualDSC signal.7. After INDIVIDUAL CALL is transmitted, the trans-ceiver will wait 8 seconds for the acknowledgment. Ifthe reply signal is not received, the transceiver willtransmit again.8. After the second INDIVIDUAL CALL is transmitted, if the reply signal is notreceived, the display will be as shown in the illustra-tion on the right. To send the call again, press the[ENT] key.9. When an individual call acknowledgment is received,the established channel is automatically changed tothe channel which is selected on step 5 above and aringing tone sounds.10. Press any key to listen to the channel to make sure itis not busy, then key the microphone and call theother vessel you desire to communicate with.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-39.png)
![GX1500SPage 40Manual CallingYou may enter an MMSI number manually to contact without the Setting up theIndividual Directory.1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear.2. Turn the CHANNEL selector knob to select “Indi-vidual.” (To cancel, select “Exit” with the CHANNELselector knob or press the [16/9] key.)3. Press the [ENT] key. The transceiver will beep, andthe “Individual directory” will appear.4. Turn the CHANNEL selector knob to select “Manual,”then press the [ENT] key.5. Turn the CHANNEL selector knob to scroll throughnumbers, 0-9. To enter the desired number and moveone space to the right press the [ENT] key. Repeatthis procedure until all nine space of the MMSI num-ber which you want to contact are entered.6. If a mistake was made entering in the MMSI numberrepeat pressing the [H/L(NAV)] key until the wrongnunber is selected, then move the channel knob tocorrect the entry.7. When finish the entering the MMSI number, pressand hold the [ENT] key.8. Press the [ENT] key, then turn the CHANNEL selec-tor knob to select the operating channel you want tocommunicate on and press the [ENT] key.9. Press the [ENT] key again to transmit the individualDSC signal.10. After INDIVIDUAL CALL is transmitted, the trans-ceiver will wait 8 seconds for the acknowledgment. Ifthe reply signal is not received, the transceiver willtransmit again.11. After the second INDIVIDUAL CALL is transmitted, ifthe reply signal is not received, the display will be asshown in the illustration on the right. To send the call again, press the [ENT]key or to exit the mode, press the [CLR] key.12. When an individual call acknowledgment is received, the established chan-nel is automatically changed to the channel which is selected on step 5above and a ringing tone sounds.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-40.png)
![Page 41GX1500S13. Press any key to listen to the channel to make sure it is not busy, then keythe microphone and call the other vessel you desire to communicate with.11.5.5 Receiving an Individual CallWhen receiving an individual call, an acknowledgment must be sent back to thecalling station. The GX1500S default setting is Automatic, but has a selectionthat allows you to manually send a reply before the radio will switch to the re-quested calling channel. This selection is useful if you want to see who is callingand requesting you to switch to a channel for communications, similar to caller idon a cellular phone.1. When an individual call is received, an individual call ringing alarm sounds.The radio automatically switches to the requestedchannel.2. Press any key to stop the alarm.3. Press the PTT on the mic and talk to the calling ship.11.5.6 Setting Up the Call Waiting FunctionAllows the GX1500S to be setup to reply (ABLE) or set the radio so it transmitsa call that advises the calling vessel the person is UNABLE to reply to the call atthis time. This function is similar to an answering machine. When set up inUNABLE and a individual call is received the Individual call from the other ves-sel is logged in the CALL WAITING directory for you to review and call back ata later time.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “INDIV ACK” withthe CHANNEL selector knob.4. Press the [ENT] key.5. Turn the CHANNEL selector knob to select “Able” or“Unable.”6. Press the [ENT] key to store the selected setting.7. To exit this menu and return to radio operation modepress the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-41.png)
![GX1500SPage 4211.6 GROUP CALLThis feature allows the user to contact a group of specific vessels (examplemembers of a yacht club) using DSC radios with Group call function to auto-matically switch to a desired channel for voice communications.11.6.1 Setting up a Group CallFor this function to operate the same Group MMSI must be programmed intoall the DSC VHF radios within the group of vessels that will be using this fea-ture. The group MMSI is a 9 digit (first digit permanently set to “0”) that will allowother radios to call your vessel along with others to automatically switch to aworking channel for voice communications. This function is very useful for yachtclubs and vessels traveling together that want to collectively make announce-ments on a predetermined channel.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “Group DIR” withthe CHANNEL selector knob.4. Press the [ENT] key, then select “Add” with theCHANNEL selector knob.5. Press the [CALL(MENU)] key.6. Turn the CHANNEL selector knob to scroll throughthe first letter of the name of the vessel or personyou want to reference in the directory.7. Press the [ENT] key to store the first letter in the nameand step to the next letter to the right.8. Repeat step 6 and 7 until the name is complete. Thename can consist of up to eleven characters, if youdo not use all eleven characters press the [ENT] keyto move to the next space. This method can also beused to enter a blank space in the name. To clear the previous letter, pressthe [CLR] key.9. After the eleventh letter or space has been entered,press and hold the [CALL(MENU)] key to advanceto the MMSI (Maritime Mobile Service Identity Num-ber) number entry.10. Turn the CHANNEL selector knob to scroll through numbers, 0-9. To enterthe desired number and move one space to the right press the [ENT] key.Repeat this procedure until all nine space of the MMSI number are entered.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-42.png)
![Page 43GX1500S11. If a mistake was made entering in the name or the MMSI number repeatpressing the [H/L(NAV)] key until the wrong charac-ter is selected, then move the channel knob to cor-rect the entry.12. To store the data entered, press and hold the [ENT]key.13. To enter another individual address, repeat steps 4 through 12.14. To exit this menu and return to radio operation mode press the [16/9] key.11.6.2 Transmitting a Group CallPre-Programmable Calling1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear.2. Turn the CHANNEL selector knob to select “Group.”(To cancel, select “Exit” with the CHANNEL selectorknob or press [16/9] key.)3. Press the [ENT] key. The transceiver will beep, andthe “Group Directory” will appear.4. Turn the CHANNEL selector knob to select the“Group” you want to contact.5. Press the [ENT] key, then turn the CHANNEL selec-tor knob to select the operating channel you want tocommunicate on and press the [ENT] key.6. Press the [ENT] key again to transmit the Group Callsignal.7. After the GROUP CALL is transmitted, all the radiosin the group will switch to the designated channel.8. Listen to the channel to make sure it is not busy, thenkey the microphone and call the other vessels youdesire to communicate with.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-43.png)
![GX1500SPage 44Manual CallingYou may enter an MMSI number manually to contact without the Setting up theGroup call number.1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear.2. Turn the CHANNEL selector knob to select “Group.”(To cancel, select “Exit” with the CHANNEL selectorknob or press [16/9] key.)3. Press the [ENT] key. The transceiver will beep, andthe “Group Directory” will appear.4. Turn the CHANNEL selector knob to select “Manual,”then press the [ENT] key.5. Turn the CHANNEL selector knob to scroll throughnumbers, 0-9. To enter the desired number and moveone space to the right press the [ENT] key. Repeatthis procedure until all nine space of the MMSI num-ber which you want to contact are entered.6. If a mistake was made entering in the MMSI numberrepeat pressing the [H/L(NAV)] key until the wrongnunber is selected, then move the channel knob tocorrect the entry.7. When finish the entering the MMSI number, pressand hold the [ENT] key.8. Press the [ENT] key to transmit the Group Call sig-nal.9. After the GROUP CALL is transmitted, all the radiosin the group will switch to the designated channel.10. Listen to the channel to make sure it is not busy, thenkey the microphone and call the other vessels youdesire to communicate with.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-44.png)
![GX1500SPage 4611.7 POSITION REQUESTAdvancements in DSC have made it possible to poll the location of anothervessel and show the position of that vessel on the display of the GX1500S.Standard Horizon has taken this feature one step further, if any Standard Hori-zon GPS is connected to the GX1500S, the polled position of the vessel isshown on the display of the GPS chart plotter making it easy to navigate to thelocation of the polled vessel. This is a great feature for anyone wanting to knowthe position of another vessel. For example your buddy that is catching fish, orfinding the location of a person you are cruising with.NOTEThe other vessel must have an operating GPS receiver connected to itsDSC transceiver and must not have its transceiver set to deny positionrequests. (Refer the section “11.5.1 Setting up the Individual / Posi-tion Call Directory” to enter information into the individual directory).11.7.1 Setting up Position ReplyThe GX1500S can be set up to automatically or manually send your position toanother vessel. This selection is important if you are concerned about some-one polling the position of your vessel that you may not want to. In the manualmode you will see the MMSI or persons name shown on the display allowingyou to choose to send your position to the requesting vessel.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appear.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “POS Reply” withthe CHANNEL selector knob.4. Press the [ENT] key.5. Turn the CHANNEL selector knob to select “Auto”or “Manual.” In “Auto” mode, after a DSC POS Re-quest is received, the radio will automatically trans-mit your vessels position. In “Manual” mode, the dis-play of the GX1500S will show who is requesting theposition.6. Press the [ENT] key to store the selected setting.7. To exit this menu and return to radio operation mode press the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-46.png)
![Page 47GX1500SThe GX1500S has the capability to turn off the Position Request ringer.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appear.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “DSC Beep” with theCHANNEL selector knob.4. Press the [ENT] key.5. Turn the CHANNEL selector knob to select “POSRequest.”6. Turn the CHANNEL selector knob to select “Off.”7. Press the [ENT] key to store the selected setting.8. To exit this menu and return to radio operation modepress the [16/9] key.If you wish to return to enabling the ringer tone, just re-peat the above procedure, turning the CHANNEL selec-tor knob to select “On” in step “6” above.11.7.2 Transmitting a Position Request to Another VesselPre-Programmable Request1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear in the display.2. Turn the CHANNEL selector knob to select “POS Re-quest.”3. Press [ENT] key to show the Position request direc-tory. This directory uses the INDIVIDUAL Directoryinformation.4. Turn the CHANNEL selector knob to select a name,then press the [ENT] key.5. Press the [ENT] key to transmit the position requestDSC call.6. When the GX1500S receives the position from thepolled vessel it is shown on the radio display andalso transferred to the GPS Chart plotter.7. If the GX1500S does not receive a reply, the displaywill be as shown in the illustration on the right. Tosend again, press the [ENT] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-47.png)
![GX1500SPage 48NOTEIf the GX1500S does not receive position data from the polled vessel,the LCD will show “NO POSITION DATA.”Manual RequestYou may enter an MMSI number manually to contact without the Setting up theIndividual / Position Call Directory.1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear in the display.2. Turn the CHANNEL selector knob to select “POS Re-quest.”3. Press [ENT] key to show the Position request direc-tory. This directory uses the INDIVIDUAL Directoryinformation.4. Turn the CHANNEL selector knob to select the“Manual,” then press the [ENT] key.5. Turn the CHANNEL selector knob to scroll throughnumbers, 0-9. To enter the desired number and moveone space to the right press the [ENT] key. Repeatthis procedure until all nine space of the MMSI num-ber which you want to contact are entered.6. If a mistake was made entering in the MMSI numberrepeat pressing the [H/L(NAV)] key until the wrongnunber is selected, then move the channel knob tocorrect the entry.7. When finish the entering the MMSI number, pressand hold the [ENT] key.8. Press the [ENT] key to transmit the position requestDSC call.9. When the GX1500S receives the position from thepolled vessel it is shown on the radio display andalso transferred to the GPS Chart plotter.10. If the GX1500S does not receive a reply, the display will be as shown in theillustration on the right. To send again, press the [ENT] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-48.png)
![Page 49GX1500S11.7.3 Receiving a Position RequestWhen a position request call is received from another vessel, a ringing alarmwill sound and POS REQUEST will be show in the LCD. Operation and trans-ceiver function differs depending on “POS Reply” in the “DSC Setup” menusetting.Automatically reply:1. When a position request call is received, a calling alarm sounds 4 times.Then requested position coordinates are transmit-ted automatically to the vessel requesting your ves-sels position.2. To exit from position request display, press any key.Manually reply:1. When a position request call is received from an-other vessel, the LCD will be as shown in the illustra-tion at the right.2. A ringing alarm sounds 4 times. Then select type ofreply function “Send” or “No Reply” by using theCHANNEL selector knob.3. The GX1500S display will show “Send” or “No Re-ply” allowing you to send your vessels location byusing the CHANNEL selector knob.4. When “Send” is selected, press the [ENT] key. And your position will betransmitted to the requesting vessel.5. To exit from position request display, press the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-49.png)
![GX1500SPage 5011.8 POSITION SENDThe feature is similar to Position Request, however instead of requesting aposition of another vessel this function allows you to send your position to an-other vessel. Your vessel must have an operating GPS receiver connected forthe GX1500S to send the position.11.8.1 Setting up a Position Send RingerThe GX1500S has the capability to turn off the Position Send ringer.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “DSC Beep” with theCHANNEL selector knob.4. Press the [ENT] key.5. Turn the CHANNEL selector knob to select “POSSend.”6. Turn the CHANNEL selector knob to select “Off.”7. Press the [ENT] key to store the selected setting.8. To exit this menu and return to radio operation modepress the [16/9] key.If you wish to return to enabling the ringer tone, just re-peat the above procedure, turning the CHANNEL selec-tor knob to select “On” in step “6” above.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-50.png)
![Page 51GX1500S11.8.2 Transmitting a DSC Position Send CallPre-Programmable Calling1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear in the display.2. Turn the CHANNEL selector knob to select the “POSSend.”3. Press the [ENT] key to select the Individual directory.4. Turn the CHANNEL selector knob to select a namein the directory, then press the [ENT] key.5. Press the [ENT] key to send your position to the se-lected vessel.Manual CallingYou may enter an MMSI number manually to contact without the Setting up theIndividual / Position Call Directory.1. Press the [CALL(MENU)] key. The “DSC Operation”menu will appear in the display.2. Turn the CHANNEL selector knob to select the “POSSend.”3. Press [ENT] key to show the Position Send directory.This directory uses the INDIVIDUAL Directory infor-mation.4. Turn the CHANNEL selector knob to select “Manual,”then press the [ENT] key.5. Enter the MMSI number (eight digits) which you wantto contact by the keypad, then press the [ENT] key.6. Press the [ENT] key to send your position to the se-lected vessel.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-51.png)
![GX1500SPage 5211.8.3 Receiving a DSC Position Send CallWhen another vessel transmits their vessels location to the GX1500S the fol-lowing will happen:1. A ringing sound will be produced when the call is received.2. Press the [16/9] key to stop ringing3. The position from the vessel sending it's position will be shown on the dis-play of the radio and also transferred to any Standard Horizon GPS Chartplotter if connected.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-52.png)
![Page 53GX1500S11.9 MANUAL INPUTTING OF THE GPS LOCATION (LAT/LON)You may send the Latitude/Longitude of your vessel manually even if theGX1500S is not connected the GPS receiver unit.After the position is entered, transmitting a DSC Distress, Position Request, orPosition Send will contain the manually entered position.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Turn the CHANNEL selector knob to select “DSCSetup” menu.3. Press the [ENT] key, then select “POS Input” withthe CHANNEL selector knob.4. Press the [ENT] key. The transceiver will beep, andthe display will be as shown in the illustration on theright.5. Enter the your local time by the 24-hour system onthe UTC time. Use the [ENT] and [H/L(NAV)] key tonavigate to each column of the time, then use theCHANNEL selector knob to select the desired num-bers in each colum. Repeat for each column, to com-plete the time.6. Enter the Latitude/Longitude of your vessel locationwith the same procedure as description above.7. To store the data entered, press the [16/9] key to exitthis menu and return to radio operation mode.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-53.png)
![GX1500SPage 5412 RADIO SETUPNOTEThe optional CMP25 RAM+ mic and VH-310 Handset can also changethe RADIO SETUP menu. Refer to page 74 (RAM+ mic) and page 81(VH-310) for details.12.1 LAMP ADJUSTINGAllows setting up the backlight intensity or to turn it off.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [CALL(MENU)] key, then select “Dimmer”in the “Radio Setup” menu with the CHANNEL se-lector knob.3. Press the [CALL(MENU)] key.4. Turn the CHANNEL selector knob to select the de-sired level. When “OFF” is selected, the lamp is ex-tinguished.5. Press the [CALL(MENU)] key to store the selectedlevel.6. To exit this menu and return to radio operation mode press the [16/9] key.12.2 LCD CONTRASTThis selection sets up the display for best viewabilty for the varying mountinglocations (overhead or below).1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Contrast” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select the de-sired level. The contrast level can be set from “00”to “31.”5. Press the [ENT] key to store the selected level.6. To exit this menu and return to radio operation modepress the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-54.png)
![Page 55GX1500S12.3 TIME OFFSETThis selection sets the time offset between local time and UTC (time GPSsends to radio). Time is displayed when GPS position (LAT/LON) is displayedby pressing the [F] key followed by the [6(NAV)] key.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Time Set” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select time off-set from UTC. See illustration below to find your off-set time from UTC. If “0:00” is assigned, the time isthe same as UTC (Universal Time Coordinated orGMT Greenwich Mean Time).5. Press the [ENT] key to store the time offset.6. To exit this menu and return to radio operation mode press the [16/9] key.OFFSET TIME TABLEFCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-55.png)
![GX1500SPage 5612.4 TIME LOCATIONThis selection selects the time display between local time and UTC (time GPSsends to radio). Time is displayed when GPS position (LAT/LON) is displayedby pressing the [F] key followed by the [6(NAV)] key.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Time Disp.” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “UTC” or“Local.”5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.n the local time mode, the display shows the time by the 12-hour system. Mean-while, the display shows the time by the 24-hour system in the UTC mode.12.5 TRUE MAGNETIC CHANGE (NAV display)This selection allows customizing the GPS COG (Course Over Ground) dis-played on the LCD to be in True or Magnetic.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Magnetic” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “On” (rep-resenting “Magnetic”) or “Off” (representing “True”).5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.(“UTC” mode)(“LOCAL” mode)FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-56.png)
![Page 57GX1500S12.6 PRIORITY CHANNEL SETAllows selection of the priority channel.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Priority CH” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select the chan-nel to be a priority.5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.12.7 SCAN TYPEThis selection selects the scan mode between “Memory Scan” and “PriorityScan.”1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “SCAN Type” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “Prior-ity” or “Memory.”5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-57.png)
![GX1500SPage 5812.8 SCAN RESUME TIMEThis selection is used to select the time the GX1500S waits after a transmis-sion ends before starting scanning.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “SCAN Resume” inthe “Radio Setup” menu with the CHANNEL selec-tor knob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select the de-sired resume time. The resume time can be set to“1sec,” “2sec,” “3sec,” or “Off.” In the “Off” selec-tion, the scanner will resume after the other stationstops transmitting (carrier drops).5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation mode press the [16/9] key.12.9 KEY BEEP (ON/OFF)This selection allows the beep tone when a key is pressed to be turned off.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Key Beep” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select “On” or“Off.”5. Press the [ENT] key to set the key beep condition.6. To exit this menu and return to radio operation modepress the [16/9] key.NOTEEmergency alarm and beeps for DSC operation cannot be turned OFF.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-58.png)
![Page 59GX1500S12.10 WX ALERTThis selection allows the radios NOAA Weather alert to be turned off. Defaultsetting is ON.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “WX Alert” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select the de-sired WX alert mode. The WX alert mode can be setto “On WX,” “On SCAN,” “On SCAN/WX,” or “Off.”5. Press the [ENT] key to store the selected setting.6. To exit this menu and return to radio operation modepress the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-59.png)
![GX1500SPage 6012.11 CHANNEL NAME CHANGEThis selection allows you to customize the name of a channel from the defaultname.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “CH Name” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select the chan-nel to be named, then press the [ENT] key.5. Turn the CHANNEL selector knob to scroll throughthe first letter of the channel name.6. Press the [ENT] key to store the first letter in the nameand step to the next letter to the right.7. Repeat step 6 and 7 until the name is complete. Thename can consist of up to twelve characters, if youdo not use all twelve characters press the [ENT] key to move to the nextspace. This method can also be used to enter a blankspace in the name. To clear the previous letter, pressthe [CLR] key.8. Press and hold the [ENT] key to enter the name andexit from the “CH Name” menu. The LCD will return to the “Radio Setup”menu.9. If you want to enter the name of another channel, select “Next” then pressthe [ENT] key. Otherwise, select “Exit” then press the [ENT] key.10. To exit this menu and return to radio operation mode press the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-60.png)
![Page 61GX1500S12.12 NAMING THE RADIO OR RAM+ STATIONSThis selection allows you to provide the name to the radio and optional RAM+Mic’s when connected.1. Press and hold down the [CALL(MENU)] key until“Radio Setup” menu appears.2. Press the [ENT] key, then select “Unit Name” in the“Radio Setup” menu with the CHANNEL selectorknob.3. Press the [ENT] key.4. Turn the CHANNEL selector knob to select the Unit(“Radio” or “RAM1”) to be named, then press the[ENT] key.5. Turn the CHANNEL selector knob to scroll throughthe first letter of the channel name.6. Press the [ENT] key to store the first letter in the nameand step to the next letter to the right.7. Repeat step 6 and 7 until the name is complete. Thename can consist of up to twelve characters, if youdo not use all twelve characters press the [ENT] keyto move to the next space. This method can also beused to enter a blank space in the name. To clear theprevious letter, press the [CLR] key.8. Press and hold the [ENT] key to enter the name andreturn to the “Unit Name” menu.9. If you want to enter the name of another unit, repeat steps 4 through 8.10. To exit this menu and return to radio operation mode press the [16/9] key.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-61.png)
![GX1500SPage 6213 ENHANCED RAM+ MIC OPERATIONWhen the RAM+ microphone is connected to the GX1500S, most VHF, DSC,setup menus and PA modes can be remotely operated. The RAM+ Mic is sup-plied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21m) using three 23 feet extension cables model CT-100. The intercom operationcan be used between the RAM+ Mic and the transceiver.13.1 RAM+ MIC CONTROLSSQUELCH CONTROL (SQL)Activates the squelch adjusting mode.Press this key to activate the squelch adjusting mode. Press themicrophone’s [] or [] key to adjust the squelch.When this key is pressed and held down for 1 second or more, the squelchis turned off.VOLUME KEY (VOL)Activates the volume adjusting mode.Press this key to activate the volume adjusting mode. Press themicrophone’s [] or [] to adjust the volume.SCAN DWNAVWXCALLSETME M ICU.I.CMENU169FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-62.png)
![Page 63GX1500SPOWER SWITCH (PWR)Press and hold down this key to turn to the transceiver and RAM+ Mic onand off.PTT (Push-To-Talk) SWITCHActivates transmission.[H/L] KEYToggles between high and low power. When the [H/L] key is pressed whilethe transceiver is on channel 13 or 67, the power will temporarily switchfrom LO to HI power until the PTT is released. The [H/L] key does notfunction on transmit inhibited and low power only channels.[](UP)/[](DOWN) KEYThese keys are used to select channels, adjust the volume and squelchlevel, and to choose the item selection of different functions (such as theDSC operation). In many ways, these keys emulate the function of thetransceiver’s CHANNEL selector knob.[16/9] KEYImmediately recalls channel 16 from any channel location. Holding downthis key recalls channel 9. Pressing the [16/9] key reverts to the previousselected working channel.Secondary usePlease see secondary use for the [WX] and [MEM] key.KEY PAD[SCAN] Key1. Starts and stops scanning of programmed channels.2. If held while the [UP()] or [DOWN()] key on the microphone arepressed, the radio will show the channels programmed in scanmemory. This function will not work if the unit is scanning.NOTE: The priority channel by default is Channel 16, however thepriority channel can be changed. To select a different priority channelrefer to section “12.7 SCAN TYPE.”[CALL/SET] KeyThe [CALL/SET] key functions as the enter key.Secondary usePress the [CALL/SET] key to access the DSC OPERATION menu.Press and hold the [CALL/SET] key to access the SETUP menu.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-63.png)
![GX1500SPage 64[DW] KeyWatches for a transmission on CH16 and another selected channel untileither signal is received. (Dual watch)Secondary usePress and hold [DW] key, intercom operation will operate between radioand RAM+ Mic.[NAV] KeyPress this key, when connected to the GPS receiver, the LCD displaysPosition Data and Time from the GPS.[WX] KeyImmediately recalls the previously selected US NOAA weather channel fromany channel location.Secondary useHolding down the [16/9] key while pressing the [WX] key switch the Chan-nel Group.NOTE: If position is displayed, this icon will be hidden.[DISTRESS] KEYUsed to send a DSC Distress Call. To send the distress call refer to section“11.3.1. Transmitting a DSC Distress Call.”FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-64.png)
![Page 65GX1500S13.2 INTERCOM OPERATION13.2.1 Communication1. Press and hold the [DW] key while in the “RADIO” mode, the mode ischanged to “INTERCOM” mode. When the “INTERCOM”operation is activated, “IC” is displayed on the RAM+ Mic(and VH-310 Handset) and “INTERCOM” is displayed onthe GX1500S.2. Press the PTT switch, “TALK” is displayed.NOTE: A warning beep is emitted whenthe RAM+ Mic PTT switch is pressedwhile the transceiver microphone’s PTTswitch is pressed.3. Speak slowly and clearly into the mi-crophone, hold the microphone about1/2 inch away from your mouth.4. When finished, release the PTT switch.5. Press the [DW] key momentarily themode will revert to “RADIO” mode.13.2.2 CallingHold down the [DW] key for 1 second or more, when the “INTERCOM” opera-tion is activated. A calling beep is emitted twice from the transceiver speaker.(RAM+ Mic’s PTT switch is pressed)(GX1500S’s PTT switch is pressed)FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-65.png)
![GX1500SPage 6613.3 DSC/RADIO SETUP MODEThe RAM+ can access the DSC / RADIO setup menu (refer to section “11DIGITAL SELECTIVE CALLING” and section “12 RADIO SETUP MODE” fordetails). The LAMP, CONTRAST, and KEY BEEP menu item accessed from theRAM+ only controls the RAM+’s display and speaker.DSC/RADIO Setup mode from the RAM+:1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu ap-pears.2. Press the []/[] key to select “RADIO SETUP” or “DSC SETUP” menu.3. Press the [CALL/SET] key, then select the menu item you wish to work onby pressing the []/[] key.4. Press the [CALL/SET] key.5. Press the []/[] key to change the value or condition for the menu item,then press the [CALL/SET] key to save the new setting.6. Press the []/[] key to select “EXIT,” then press the [CALL/SET] key toreturn to the normal operation.RADIO SETUP-menu DSC SETUP-menuNOTEWhen setup menu is selected, the GX1500S will be temporarily disableduntil the RAM+ mic, exits from the setup mode.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-66.png)
![GX1500SPage 6814 VH-310 HANDSET OPERATIONWhen the VH-310 HANDSET is connected to the GX1500S, most VHF, DSC,setup menus and PA modes can be remotely operated as the same manner dueto the front panel’s keypad of the transceiver. The VH-310 HANDSET is suppliedwith 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) usingthree 23 feet extension cables model CT-100. The intercom operation can beused between the VH-310 HANDSET and RAM+ Mic or the GX1500S.14.1 VH-310 HANDSET CONTROLSPWR keyPress and hold down this key to turn tothe transceiver and VH-310 HANDSETon and off.PTT (Push-To-Talk) SwitchActivates transmission.[H/L] keyToggles between high and low power.When the [H/L] key is pressed while thetransceiver is on channel 13 or 67, thepower will temporarily switch from “LO”to “HI” power until the PTT is released.The [H/L] key does not function on transmit in-hibited and low power only channels.[DISTRESS] keyUsed to send a DSC Distress Call. To send thedistress call refer to section “11.3.1. Transmit-ting a DSC Distress Call.”KEY BUTTON[VOL] keyActivates the volume adjusting mode.Press this key to activate the volume adjusting mode.Press the [] or [] to adjust the volume.NOTEWhen the VH-310 handset is removed from the cradle the speakeraudio will be automatically reduced so not to damage your hearing.When the VH-310 is in the cradle the speaker audio will increase socommunications can be heard.due to o t pa e s eypad o t e t a sce e ;FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-68.png)
![Page 69GX1500S[SQL] keyActivates the squelch adjusting mode.Press this key to activate the squelch adjusting mode. Press the [] or[] key to adjust the squelch.[CALL(MENU)] keyThe [CALL(MENU)] key functions as the enter key.Secondary usePress the [CALL(MENU)] key to access the DSC OPERATION menu.The “INDIVIDUAL CALL,” “GROUP CALL,” “ALL SHIP CALL,” “POSI-TION REQUEST,” POSITION SEND,” STANDBY MODE,” and “CALLWAITING” functions can be accessed from the DSC OPERATION menu.Press and hold the [CALL(MENU)] key to access the RADIO SETUP(refer ro section 12) or DSC SETUP menu (refer to section 11).[F] keyActivates the “Alternate” key function.Press this key to activates the “Alternate” key function of the ten keypad.[16/9] keyImmediately recalls channel 16 from any channel location. Holding downthis key recalls channel 9. Pressing the [16/9] key reverts to the previousselected working channel.Secondary usePress and hold the [16/9] key then press the [WX] key to switch the USA,International or Canadian channels.[WX] keyImmediately recalls the previously selected US NOAA weather channelfrom any channel location.Secondary useHolding down the [16/9] key while pressing the [WX] key switches theChannel Group.[] / [] KEYThese keys are used to select channels, adjust the volume and squelchlevel, and to choose the item selection of different functions (such as DSCoperation).FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-69.png)
![GX1500SPage 70KEYPAD[1(DIM)] keyWhen in radio mode, this key is used to directly select channel digit “1” ina channel number.Secondary usePress the [F] key first then press the [1(DIM)] key to access the LCDDimmer menu. Refer to section “12.1 LAMP ADJUSTING” for details.[2(MEM)] KeyWhen in radio mode, this key is used to directly select channel digit “2” ina channel number.Secondary usePress the [F] key first then press the [2(MEM)] key, memorize the se-lected channel into the transceiver scan memory for scanning. Whenrepeat the same procedures ([F] [2(MEM)]), will delete the channelfrom the scan memory. Refer to section “10.12 SCANNING” for details.[3(SCAN)] KeyWhen in radio mode, this key is used to directly select channel digit “3” ina channel number.Secondary usePress the [F] key first then press the [3(SCAN)] key to start and stop thescanning of programmed channels. Refer to section “10.12 SCANNING”for details.[4(DW)] KeyWhen in radio mode, this key is used to directly select channel digit “4” ina channel number.Secondary usePress the [F] key first then press the [4(DW)] key to scan for voice com-munications on the priority channel and another selected channel until asignal is received on either channel (Dual Watch). Refer to section “10.11DUAL WATCH (TO PRIORITY CHANNEL)” for details.[5(IC)] KeyWhen in radio mode, this key is used to directly select channel digit “5” ina channel number.Secondary usePress the [F] key then press the [5(IC)] key to activate intercom functionbetween RAM+(s) or VH-310 handset(s).Refer to section “14.2 INTERCOM OPERATION” for details.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-70.png)
![Page 71GX1500S[6(NAV)] KeyWhen in radio mode, this key is used to directly select channel digit “6” ina channel number.Secondary usePress the [F] key first then press the [6(NAV)] key, the LCD will displayNAV GPS Data, Time, SOG (Speed Over Ground), and COG (CourseOver Ground) when a GPS is connected to the accessory cable of theGX1500S. See section “8.4 CONNECTION OF GPS WITH NMEA OUT-PUT” for details.[7(SCRM)] KeyWhen in radio mode, this key is used to directly select channel digit “7” ina channel number.[8(PA)] KeyWhen in radio mode, this key is used to directly select channel digit “8” ina channel number.[9(FOG)] KeyWhen in radio mode, this key is used to directly select channel digit “9” ina channel number.[0] KeyWhen in radio mode, this key is used to directly select channel digit “0” ina channel number.Secondary useUsed to select A (alpha channels). Press the desired channel keys thenpress and hold [0] key until “A” appears next to the channel number andpress [ENT] to select the channel.[CLR] KeyPress the [CLR] key to cancel the menu selection and/or keypad entry.[ENT] KeyPress the [ENT] key to enter the menu selection and/or keypad entry.Note: The channel number entering is the same as the manner due to frontpanel’s keypad of the GX1500S; press the key with the first digit then press thekey with the second digit and press the [ENT] key to switch to the channel.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-71.png)
![GX1500SPage 7214.2 INTERCOM OPERATION14.2.1 Communication1. Press the [F] key followed by the [5(IC)] key, the mode is changed to “IN-TERCOM” mode.2. If your GX1500S is equipped with two VH-310 Handsets (or RAM+ Mics),select the station you wish to communicate (RADIO, RAM, or ALL) with the[]/[] key, then press the [ENT] key.3. When the “INTERCOM” operation is activated, “IC” is dis-played on the VH-310 Handset (and RAM+ Mic, if used)and “INTERCOM” is displayed on the GX1500S.4. Press the PTT switch, “TALK” is displayed.NOTE: A warning beep is emitted when the RAM+ Mic PTTswitch is pressed while the transceivermicrophone’s PTT switch is pressed.5. Speak slowly and clearly into the mi-crophone, hold the microphone about1/2 inch away from your mouth.6. When finished, release the PTT switch.7. To exit the “INTERCOM” mode andreturn to radio operation mode, pressthe [F] key followed by the [5(IC)] keyagain.14.2.2 CallingPress and hold the [5(IC)] key for 1 second when the “INTERCOM” operation isactivated, a calling beep is emitted from the GX1500S speaker.(VH-310’s PTT switch is pressed)(GX3500S’s PTT switch is pressed)FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-72.png)
![Page 73GX1500S14.3 MANUAL INPUTTING OF THE GPS LOCATION (LAT/LON)You may send the Latitude/Longitude of your vessel manually from the VH-310Handset even if the GX1500S is not connected the GPS receiver unit.After the position is entered, transmitting a DSC Distress, Position Request, orPosition Send will contain the manually entered position.1. Press and hold down the [CALL(MENU)] key until “RadioSetup” menu appears.2. Press the [] key to select “DSC SETUP” menu.3. Press the [ENT] key, then select “POS INPUT” with the []/[] key.4. Press the [ENT] key then, enter the your local time from thekeypad by the 24-hour system on the UTC time.6. Enter the Latitude of your vessel location (xx.xx.xx) by thekeypad, then press the [6(NAV)] key to select North (N), or[7(SCRM)] key to select South (S).6. Enter the Longitude of your vessel location (xxx.xx.xx) bythe keypad, then press the [3(SCAN)] to select East (E), or[9(FOG)] key to select West (W).7. If a number was entered by mistake, press the H/L key re-peatedly to select the number. Press the []/[] key to se-lect the desired number.8. Press and hold in the [ENT] key to store the data entered,then press the [16/9] key to exit this menu and return toradio operation mode.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-73.png)
![GX1500SPage 7414.4 DSC/RADIO SETUP MODEThe VH-310 Handset can access the DSC / RADIO setup menu (refer to sec-tion “11 DIGITAL SELECTIVE CALLING” and section “12 RADIO SETUPMODE” for details). The CONTRAST, NAV DISPLAY, KEY BEEP, and AF SE-LECT menu item accessed from the VH-310 Handset only controls the VH-310Handset’s display and speaker.DSC/RADIO Setup mode from the VH-310 Handset:1. Press and hold down the [CALL(MENU)] key until “RADIO SETUP” menuappears.2. Press the []/[] key to select “RADIO SETUP” or “DSC SETUP” menu.3. Press the [ENT] key, then select the menu item you wish to work on bypressing the []/[] key.4. Press the [ENT] key.5. Press the []/[] key to change the value or condition for the menu item,then press the [ENT] key to save the new setting.6. Press the []/[] key to select “EXIT,” then press the [ENT] key to returnto the normal operation.RADIO SETUP-menu DSC SETUP-menuNOTEWhen the SETUP menu is selected, using the VH-310 Handset, theGX1500S will be temporarily disabled until the VH-310 Handset exitsfrom the setup mode.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-74.png)
![Page 75GX1500S14.4.1 Changing GPS Information to Vessel position or COGAllows customizing the NAV data showing GPS Information. Factory default is“Your Vessel’s Current Position,” however, following the steps below the GPSInformation can be changed to “Course Over Ground (COG).”1. Press and hold down the [CALL(MENU)] key until “RADIOSETUP” menu appears.2. Press the [ENT] key, then select “NAV DISPLAY” with the[]/[] key.3. Press the [CALL(SET)MENU] key.4. Press the [] or [] key to select “Pos (Your Vessel’s Cur-rent Position)” or “Cru (Course Over Ground).”5. Press the [ENT] key to store the data entered, then pressthe [16/9] key to exit this menu and return to radio operationmode.14.4.2 External Speaker AF SelectionThe AF SELECT menu allows you to set the audio output level of the VH-310’sExternal Speaker to “fixed” regardress the VOL level setting of the VH-310,which is useful to the case when use with the amplified speaker, such as theStandard Horizon MLS-310.1. Press and hold down the [CALL(MENU)] key until “RadioSetup” menu appears.2. Press the [ENT] key, then select “AF SELECT” with the []/[] key.3. Press the [ENT] key.4. Press the [] or [] key to select “Pr” (External SpeakerLevel is “Fixed”) or “Po” (External Speaker Level is “Adjust-able”).5. Press the [ENT] key to store the data entered, then pressthe [16/9] key to exit this menu and return to radio operationmode.FCC ID: K6630173X3D/IC ID: 511B-30173X3DVertex Standard Co., Ltd.](https://usermanual.wiki/Yaesu-Musen/30173X3D/User-Guide-614888-Page-75.png)
