Yaesu Musen FT-8800R Amateur Scanning Receiver User Manual C DATA FT 8800 P65

Yaesu Musen Co., Ltd. Amateur Scanning Receiver C DATA FT 8800 P65

users manual

DUAL BAND FM TRANSCEIVERFT-8800ROPERATING MANUALVERTEX STANDARD CO., LTD.4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, JapanVERTEX STANDARDUS Headquarters10900 Walker Street, Cypress, CA 90630, U.S.A.International Division8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.YAESU EUROPE B.V.P.O. Box 75525, 1118 ZN Schiphol, The NetherlandsYAESU UK LTD.Unit 12, Sun Valley Business Park, Winnall CloseWinchester, Hampshire, SO23 0LB, U.K.VERTEX STANDARD HK LTD.Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,Kwun Tong, Kowloon, Hong KongFCC ID: K66FT-8800RVertex Standard Co., Ltd.
ContentsIntroduction ........................................................ 1Specifications ...................................................... 2Accessories & Options ....................................... 3Supplied Accessories ....................................... 3Optional Accessories ....................................... 3Installation .......................................................... 4Preliminary Inspection .................................... 4Installation Tips ............................................... 4Safety Information ........................................... 5Antenna Considerations .................................. 6Mobile Installation ........................................... 8Transceiver Installation ............................... 8Mobile Power Connections ........................ 9Mobile Speakers .......................................... 9Base Station Installation ................................ 10AC Power Supplies ................................... 10Packet Radio Terminal Node Controller .10Front Panel Controls & Switches.................. 12LCD .................................................................... 16Rear Panel Connections .................................. 17MH-48A6J Microphone ..................................... 18MH-42B6JS Microphone ................................... 19Basic Operation................................................ 20Turning the Transceiver On and Off ............ 20Adjusting the Squelch Setting ...................... 20Selecting the Operating Band ....................... 20Selecting the Frequency Band ...................... 21Frequency Navigation ................................... 22Tuning Dial ................................................ 22Direct Keypad Frequency Entry ............... 22Scannig ...................................................... 22Transmission .................................................. 23Changing the Transmitter Power Level ... 23Advanced Operation ....................................... 24Lock Feature .................................................. 24Keyboard Beeper ........................................... 24Channel Step Selection ................................. 24Display Brightness......................................... 25Band Linking ................................................. 25Audio Muting................................................. 26RF Squelch ..................................................... 26Repeater Operation ......................................... 27Repeater Shifts ............................................... 27Automatic Repeater Shift (ARS) .................. 27Manual Repeater Shift Activation ................ 28Changing the Default Repeater Shift ....... 28CTCSS/DCS Operation .................................. 29CTCSS Operation .......................................... 29DCS Operation .............................................. 30Tone Search Scanning ................................... 31Memory Operation .......................................... 32Regular Memory Channel Operation ........... 32Memory Storage ........................................ 32Memory Recall .......................................... 34Memory Offset Tuning ............................. 34Deleting Memories .................................... 34HOME Channel Memory ......................... 35Memory Bank Operation .......................... 36Memory Only Mode .................................. 36Hyper Memory Mode .................................... 37Hyper Memory Storage ............................. 37Hyper Memory Recall ............................... 37Scanning ............................................................ 38Setting the Scan-Resume Technique ........... 38VFO Scanning ............................................... 39Memory Scanning ......................................... 40How to Skip (Omit) a Channel         During Memory Scan Operation .... 40Preferential Memory Scan ........................ 41Programmable (Band Limit) Memory Scan .. 42“Priority Channel” Scanning (Dual Watch).. 43Smart Search .................................................... 44ARTSTM: Auto Range Transponder System .... 46Basic ARTS Setup and Operation ................ 46CW Identifier Setup....................................... 47DTMF Autodialer Operation......................... 48Internet Connection Feature.......................... 50Miscellaneous Settings .................................... 52Time-Out Timer ............................................. 52Automatic Power Off .................................... 52Programming the Key Assignment .............. 53FM Bandwith & MIC Gain Control ............. 54DCS Code Inversionm .................................. 55Cross Band Repeater Operation ................... 56Reset Procedure ............................................... 57Cloning ............................................................... 58Menu (“Set”) Mode ......................................... 59FCC ID: K66FT-8800RVertex Standard Co., Ltd.
1FT-8800R Operating ManualINTRODUCTIONThe FT-8800R is a ruggedly-built, high quality Dual Band FM transceiver providing 50Watts of power output on the 144 MHz Amateur bands and 35 Watts on the 430 MHz band.The high power output of the FT-8800R is produced by its RD70HVF1 Power MOS FETamplifier, with a direct-flow heat sink and thermostatically-controlled cooling fan maintain-ing a safe temperature for the transceiver’s circuitry.Featuring 1054 memory channels (527 channels for “Main” band plus 527 channels for“Sub” band), full duplex operation with independent Volume and Squelch controls, andbuilt-in CTCSS and DCS encoder/decoder circuits, the FT-8800R includes provision forremote-head mounting, utilizing the optional YSK-8900 Separation Kit, which allows in-stallation evening the most compact of cars.We recommend that you read this manual in its entirety, so as to understand fully the manyfeatures of your new FT-8800R transceiver.146523LOWSQL SQLVOLVOLLOWV/MHMSCNV/MHMSCNKEY2PWRFCC ID: K66FT-8800RVertex Standard Co., Ltd.
2FT-8800R Operating ManualGENERALFrequency Range:RX: 108.000 - 520.000 MHz,700.000 - 999.995 MHz (Cellular Blocked)TX: 144.000 - 146.000 MHz (or 144.000 - 148.000 MHz),430.000 - 440.000 MHz (or 430.00 - 450.000 MHz)Channel Steps:5/10/12.5/15/20/25/50 kHzModes of Emission:F3, F2, F1Antenna Impedance:50 Ohms, unbalanced (Antenna Duplexer built-in)Frequency Stability:±5 ppm @ 14° F ~ +140° F (–10 °C ~ +60 °C)Operating Temperature Range:–4° F ~ +140° F (–20 °C ~ +60 °C)Supply Voltage:13.8 VDC (±15%), negative groundCurrent Consumption (Approx.): RX: 0.5 A (Squelched)TX: 8.5 A (144 MHz), 8.0 A (430 MHz)Case Size (W x H x D): 5.5” x 1.6” x 6.6” (140 x 41.5 x 168 mm)(w/o knobs & connectors)Weight (Approx.): 2.2 lb (1 kg)TRANSMITTEROutput Power:50/20/10/5 W (144 MHz),35/20/10/5 W (430 MHz)Modulation Type: Variable ReactanceMaximum Deviation: ±5 kHzSpurious Radiation: Better than –60 dBMicrophone Impedance: 2 kWDATA Jack Impedance: 10 kWRECEIVERCircuit Type: Double-conversion superheterodyneIntermediate Frequencies: 45.05 MHz/450 kHz (Main band),47.25 MHz/450 kHz (Sub band)Sensitivity (for 12dB SINAD): Better than 0.2 µVSquelch Sensitivity: Better than 0.16 µVSelectivity (–6dB/–60dB): 8 kHz/30 kHzMaximum AF Output: 2 W @ 8 W for 5% THDAF Output Impedance: 4-16 WSpecifications are subject to change without notice, and are guaranteed within the 144 and430 MHz amateur bands only. Frequency ranges will vary according to transceiver ver-sion; check with your dealer.SPECIFICATIONSFCC ID: K66FT-8800RVertex Standard Co., Ltd.
3FT-8800R Operating ManualSUPPLIED ACCESSORIESMicrophone MH-48A6J or MH-42B6JS (depending on transceiver version) .....................1Mobile Mounting Bracket MMB-36 ..............................................................................1DC Power Cord w/Fuse (T9021715) ..............................................................................1Spare Fuse 15 A (Q0000081) .........................................................................................2Operating Manual..........................................................................................................1Warranty Card ...............................................................................................................1OPTIONAL ACCESSORIESMH-48A6J DTMF Microphoneø1MH-42B6JS Hand Microphoneø1YSK-8900 Separation KitMEK-2 Microphone Extension Kitø2MLS-100 High-Power External SpeakerFP-1023 AC Power Supply (25A: USA only)FP-1030A AC Power Supply (30A)CT-39A Packet Interface CableAvailability of accessories may vary. Some accessories are supplied as standard per localrequirements, while others may be unavailable in some regions. Consult your Yaesu dealerfor details regarding these and any newly-available options Connection of any non-Yaesu-approved accessory, should it cause damage, may void the Limited Warranty on this appa-ratus.ø1:If you replace the microphone from the MH-48A6J to MH-42B6JS or vice versa, per-form Menu #23 (MIC). See page 63 for details.ø2:When using the MH-48A6J or MH-42B6JS microphone in conjunction with the MEK-2,in some cases, the [P1] through [P4] functions may operate erratically.ACCESSORIES & OPTIONSFCC ID: K66FT-8800RVertex Standard Co., Ltd.
4FT-8800R Operating ManualThis chapter describes the installation procedure for integrating the FT-8800R into a typi-cal amateur radio station. It is presumed that you possess technical knowledge and concep-tual understanding consistent with your status as a licensed radio amateur. Please take someextra time to make certain that the important safety and technical requirements detailed inthis chapter are followed closely.PRELIMINARY INSPECTIONInspect the transceiver visually immediately upon opening the packing carton. Confirm thatall controls and switches work freely, and inspect the cabinet for any damage. Gently shakethe transceiver to verify that no internal components have been shaken loose due to roughhandling during shipping.If any evidence of damage is discovered, document it thoroughly and contact the shippingcompany (or your local dealer, if the unit was purchased over-the-counter) so as to getinstructions regarding the prompt resolution of the damage situation. Be certain to save theshipping carton, especially if there are any punctures or other evidence of damage incurredduring shipping; if it is necessary to return the unit for service or replacement, use the origi-nal packing materials but put the entire package inside another packing carton, so as topreserve the evidence of shipping damage for insurance purposes.INSTALLATION TIPSTo ensure long life of the components, be certain to provide adequate ventilation around thecabinet of the FT-8800R.Do not install the transceiver on top of another heat-generating device (such as a powersupply or amplifier), and do not place equipment, books, or papers on top of the FT-8800R.Avoid heating vents and window locations that could expose the transceiver to excessivedirect sunlight, especially in hot climates. The FT-8800R should not be used in an environ-ment where the ambient temperature exceeds +140° F (+60° C).INSTALLATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
5FT-8800R Operating ManualSAFETY INFORMATIONThe FT-8800R is an electrical apparatus, as well as a generator of RF (Radio Frequency)energy, and you should exercise all safety precautions as are appropriate for this type ofdevice. These safety tips apply to any device installed in a well-designed amateur radiostation.Never allow unsupervised children to play in the vicinity of your transceiver or an-tenna installation.Be certain to wrap any wire or cable splices thoroughly with insulating electricaltape, to prevent short circuits.Do not route cables or wires through door jambs or other locations where, throughwear and tear, they may become frayed and shorted to ground or to each other.Do not stand in front of a directional antenna while you are transmitting into thatantenna. Do not install a directional antenna in any location where humans or petsmay be walking in the main directional lobe of the antenna’s radiation pattern.In mobile installations, it is preferable to mount your antenna on top of the roof of thevehicle, if feasible, so as to utilize the car body as a counterpoise for the antenna andraise the radiation pattern as far away from passengers as possible.During vehicular operation when stopped (in a parking lot, for example), make it apractice to switch to Low power if there are people walking nearby.Never wear dual-earmuff headphones while driving a vehicle.Do not attempt to drive your vehicle while making a telephone call on an autopatchusing the DTMF microphone. Pull over to the side of the road, whether dialing manu-ally or using the auto-dial feature.INSTALLATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
6FT-8800R Operating ManualANTENNA CONSIDERATIONSThe FT-8800R is designed for use with antennas presenting an impedance of near 50 Ohmsat all operating frequencies. The antenna (or a 50 Ohm dummy load) should be connectedwhenever the transceiver is turned on, to avoid damage that could otherwise result if trans-mission occurs accidentally without an antenna.Ensure that your antenna is designed to handle 50 Watts of transmitter power. Some mag-netic-mount mobile antennas, designed for use with hand-held transceivers, may not becapable of withstanding this power level. Consult the antenna manufacturer’s specificationsheet for details.Most all FM work is performed using vertical polarization. When installing a directionalantenna such as a Yagi or Cubical Quad, be certain to orient it so as to produce verticalpolarization, unless you are engaged in a special operating situation where horizontal polar-ization is used. In the case of a Yagi antenna, orient the elements vertically for verticalpolarization; for a Cubical Quad, the feedpoint should be at the center of one of the verticalsides of the driven element (or at a side corner, in the case of a diamond-shaped CubicalQuad).Note that this transceiver is designed with wide frequency coverage in the VHF/UHF spec-trum. For general listening, you may wish to have a broadband antenna such as a disconeavailable, as a directional antenna such as a Yagi will have degraded performance outsidethe Amateur band for which it is designed.Excellent reference texts and computer software are available for the design and optimiza-tion of VHF and UHF antennas. Your dealer should be able to assist you with all aspects ofyour antenna installation requirements.Use high-quality 50 Ohm coaxial cable for the lead-in to your FT-8800R transceiver. Allefforts at providing an efficient antenna system will be wasted if poor quality, lossy coaxialcable is used. Losses in coaxial lines increase as the frequency increases, so an 8-meter-long(25’) coaxial line with 1/2 dB of loss at 29 MHz may have a loss of 6 dB or more at 446MHz; choose your coaxial cable carefully based on the installation location (mobile vs.base) and the overall length of the cable required (for very short runs of cable in a mobileinstallation, the smaller, more flexible cable types may be acceptable).INSTALLATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
7FT-8800R Operating ManualINSTALLATIONANTENNA CONSIDERATIONSFor reference, the chart below shows approximate loss figures for typically-available co-axial cables frequently used in VHF/UHF installations.Loss in dB per 30 m (100 feet) for Selected 50-Ohm Coaxial Cables(Assumes 50-ohm Input/Output Terminations)CABLE TYPERG-58ARG-58 FoamRG-213RG-8 FoamBelden 9913Times Microwave LMR-4007/8” “Hardline”LOSS: 144 MHZ6.54.73.02.01.51.50.7LOSS: 430 MHZ> 1085.93.72.92.61.3Loss figures are approximate; consult cable manufacturers’ catalogs forcomplete specifications.In outdoor installations, be certain to weatherproof all connectors thoroughly, as water en-tering a coaxial cable will cause losses to escalate rapidly, thus diminishing your communi-cations effectiveness. The use of the shortest possible length of the highest quality coaxialcable that fits within your budget will ensure the best performance from your FT-8800R.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
8FT-8800R Operating ManualINSTALLATIONMOBILE INSTALLATIONThe FT-8800R must only be installed in vehicles having a 13.8 Volt negative ground elec-trical system. Mount the transceiver where the display, controls, and microphone are easilyaccessible, using the supplied MMB-36 mounting bracket.The transceiver may be installed in almost any location, but should not be positioned near aheating vent nor anywhere where it might interfere with driving (either visually or mechani-cally). Make sure to provide plenty of space on all sides of the transceiver so that air canflow freely around the radio’s case. Refer to the diagrams showing proper installation proce-dures.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
9FT-8800R Operating ManualMobile Power ConnectionsTo minimize voltage drop and avoid blowing the vehicle’s fuses, connect the supplied DCpower cable directly to the battery terminals. Do not attempt to defeat or bypass the DCcable’s fuse – it is there to protect you, your transceiver, and your vehicle’s electricalsystem.Warning!Never apply AC power to the power cable of the FT-8800R, nor DC voltage greaterthan 15.8 Volts. When replacing the fuse, only use a 15-A fast-blow type. Failure toobserve these safety precautions will void the Limited Warranty on this product.rBefore connecting the transceiver, check the voltage at the battery terminals while rev-ving the engine. If the voltage exceeds 15 Volts, adjust the vehicle’s voltage regulatorbefore proceeding with installation.rConnect the RED power cable lead to the POSITIVE (+) battery terminal, and the BLACKpower cable lead to the NEGATIVE (–) terminal. If you need to extend the power cable,use #12 AWG or larger insulated, stranded copper wire. Solder the splice connectionscarefully, and wrap the connections thoroughly with insulating electrical tape.rBefore connecting the cable to the transceiver, verify the voltage and polarity of thevoltage at the transceiver end of the DC cable using a DC voltmeter. Now connect thetransceiver to the DC cable.INSTALLATIONMOBILE INSTALLATIONMobile SpeakersThe optional MSL-100 External Speaker includes its own swivel-type mounting bracket,and is available from your Yaesu dealer.Other external speakers may be used with the FT-8800R, if they present the specified 8-Ohm impedance and are capable of handling the 2 Watts of audio output supplied by the FT-8800R.Cabin  Engine Roomß  àFT-8900RBatteryRED: Positive (+)BLACK: Negative (–)FT-8800RFCC ID: K66FT-8800RVertex Standard Co., Ltd.
10 FT-8800R Operating ManualBASE STATION INSTALLATIONThe FT-8800R is ideal for base station use as well as in mobile installations. The FT-8800R is specifically designed to integrate into your station easily, using the information tofollow as a reference.AC Power SuppliesOperation of the FT-8800R from an AC line requires a power source capable of providingat least 15 Amps continuously at 13.8 Volts DC. The FP-1023 and FP-1030A AC PowerSupplies are available from your Yaesu dealer to satisfy these requirements. Other well-regulated power supplies may be used, as well, if they meet the above voltage and currentspecifications.Use the DC power cable supplied with your transceiver for making power connections to thepower supply. Connect the RED power cable lead to the POSITIVE (+) power supplyterminal, and connect the BLACK power cable lead to the NEGATIVE (–) power supplyterminal.Packet Radio Terminal Node Controller (TNC)The FT-8800R provides a convenient rear-panel DATA jack for easy connections to yourTNC. This connector is a standard mini-DIN connector. A pre-wired connector and cableassembly option, model CT-39A, is available from your local Yaesu dealer.The FT-8800R’s DATA jack connections are optimized for the data transmission and recep-tion speed in use. In accordance with industry standards, the signal levels, impedances, andbandwidths are significantly different on 9600 bps as opposed to 1200 bps. If your TNCdoes not provide multiple lines to accommodate such optimization, you may still be able toutilize your TNC, if it is designed for multiple-radio use, by connecting the TNC “Radio 1”port to the 1200 bps lines on the FT-8900R, and the “Radio 2” port to the 9600 bps lines.The pin connections of the Data connector are shown below.INSTALLATIONPin123456LabelPKD(DATA IN)GNDPTTRX9600RX1200PKS(SQL)NotePacket Data InputImpedance: 10 kW,Maximum Input Level: 40 mV p-p for 1200 bps     2.0 Vp-p for 9600 bpsSignal GroundGound to Transmit9600 bps Packet Data OutputImpedance: 10 kW, Maximum Output: 500 mV p-p1200 bps Packet Data OutputImpedance: 10 kW, Maximum Output: 300 mV p-pSquelch ControlSquelch Open: +5 V, Squelch Close: 0 VCT-39A Wire ColorBrownRedOrangeYellowGreenBlueDATA Jack Pin OutFCC ID: K66FT-8800RVertex Standard Co., Ltd.
11FT-8800R Operating ManualINSTALLATIONNote that 9600 bps packet transmit-deviation adjustment is very critical to successful opera-tion, and can only be accomplished using a calibrated deviation meter (such as that found onan FM Service Monitor used in a communications service center). In most cases, the PacketData Input level (set via a potentiometer inside the TNC) must be adjusted to provide adeviation of ±2.75 kHz (±0.25 kHz). Check with your packet node’s sysop if you have anyquestions about the appropriate deviation level for your network. Note also that high through-put on 9600 bps frequently requires strong signals, so you may wish to consider the use of adirectional antenna such as a Yagi for communication with high-speed packet nodes.The setting of the 1200 bps Packet Data Input level is much less critical than it is at 9600 bps,and satisfactory adjustment to the optimum (±2.5 ~ ±3.5 kHz) deviation can usually be done“by ear” by adjusting the TNC’s 1200 bps TX Audio Level potentiometer so that the outgoingpackets (as monitored on a separate VHF or UHF receiver) are approximately the same levelas (A) the DTMF tones or (B) the 1750 Hz Burst tone produced using the microphone.Finally, note that the Menu (“Set”) mode allows you to set the Packet data rate (1200 or9600 bps) independently for each band, and set the Packet operating Band (Main band,Right band, or Left band). If you have trouble getting your FT-8800R to respond correctlyduring packet operation, check to be certain that you do not have Menu #26 (PCKT S) set tothe wrong data rate, and/or Menu #27 (PCKT B) set to the wrong operating band.BASE STATION INSTALLATION13.8VDCANTEXT SPDATADATAOUTDATAIN PTTPKSGNDDATA INDATA OUT(9600bps)13.8VDCANTEXT SPDATADATAOUTDATAIN PTTPKSGNDDATA INDATA OUT(1200bps)9600bps Packet Setup1200bps Packet SetupFCC ID: K66FT-8800RVertex Standard Co., Ltd.
12 FT-8800R Operating Manualj“Left” DIAL knobThis 20-position detented rotary switch is the tuning dial for the “left” band. Press thisknob momentarily to switch the “Main band” to be the “left” band.When the “left” band is set to be the “Main band” in the VFO mode, press this knob toenable rapid tuning (in 1 MHz steps) using this knob.Press and hold in this knob for 1/2 second to toggle the operating band on the “left” sideas follows:144 MHz à 250 MHz à 350 MHz à 430 MHz à  850 MHz à 144 MHz ......k“Left” VOLSQL KnobThe inner VOL (Volume) control adjusts the speaker audio level form the “left” re-ceiver. Clockwise rotation increases the audio level.Press this knob momentarily to switch the Internet Connection feature “on” and “off.”The outer SQL (Squelch) control is used to silence background noise on the “left”receiver. It should be advanced clockwise just to the point where the noise is silenced(and the “ ” indicator on the display turns off), so as to provide the best sensitivityto weak signals.lHyper Memory Buttons ([1] ~ [6])Press and hold in one of these buttons for 2 seconds to store the current total configura-tion of the radio into a special “Hyper” memory bank.Press the appropriate button momentarily to recall the desired “Hyper” memory.FRONT PANEL CONTROLS & SWITCHES146523LOWSQL SQLVOLVOLLOWV/MHMSCNV/MHMSCNKEY2PWRjkqpmlonFCC ID: K66FT-8800RVertex Standard Co., Ltd.
13FT-8800R Operating ManualFRONT PANEL CONTROLS & SWITCHESm“Left” Side Keys[LOW] KeyPress this key momentarily to select the transmitter power output level of the “left” band(“LOW,” “MID2,” “MID1,” or “HIGH”).When the “left” band is set to the Memory mode or Home Channel, press and hold inthis key for 1/2 second to switch the memory channel display between the “Frequency”format and “Alpha-numeric Tag” format.[V/M] KeyPress this key momentarily to switch the frequency control for the “left” band betweenthe VFO and Memory Systems.When the “left” band is set to the VFO mode, press and hold in this for 1/2 second toactivate the Smart Search Feature.When the “left” band is set to the Memory mode, press and hold in this key for 1/2second to shift to the “Memory Tuning” feature.[HM] KeyPress this key momentarily to recall a favorite “Home” frequency memory.Press and hold in this key for 1/2 second to activate Priority Channel Scanning.[SCN] KeyPress this key momentarily to activate the Scanner on the “left” band.When the “left” band is set to the Memory mode, press and hold in this key for 1/2second to set up the Scan Skip List or Preferential Scan List.n[SET] KeyPress this key momentarily to enter the Set (“Menu”) mode.Press and hold in this for 1/2 second to transfer the contents of the “Main band” VFOinto a Memory register.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
14 FT-8800R Operating Manualo“Right” Side KeysThe “right” side ([LOW], [V/M], [HM], and [SCN]) keys may be set to either oftwo function sets via Menu #20 (KEY.MOD). See page 63 for the setup proce-dure.[LOW] Key ([MHz] Key)Key Mode “1” ([LOW] Key: Default)Press this key momentarily to select the transmitter power output level of the “right”band (“LOW,” “MID2,” “MID1,” or “HIGH”).When the “right” band is set to the Memory mode or Home Channel, press and hold inthis key for 1/2 second to switch the memory channel display between the “Frequency”format and the “Alpha-numeric Tag” format.Key Mode “2” ([MHz] Key)Press this key momentarily to allow tuning in 1-MHz steps on the “Main” band VFO.Press and hold in this key for 1/2 second to allow tuning in 10-MHz steps on the “Main”band VFO.[V/M] Key ([REV] Key)Key Mode “1” ([V/M] Key: Default)Press this key momentarily to switch the frequency control for the “right” band betweenthe VFO and Memory Systems.When the “right” band is set to the VFO mode, press and hold in this for 1/2 second toactivate the Smart Search Feature.When the “right” band is set to the Memory mode, press and hold in this key for 1/2second to shift to the “Memory Tuning” feature.Key Mode “2” ([REV] Key)Press this key momentarily to reverse the transmit and receive frequencies on the “Main”band during split-frequency (i.e. “Repeater”) operation.Press and hold in this key for 1/2 second to change the frequency shift direction: RPT –(minus shift), RPT + (plus shift), or RPT OFF (simplex).[HM] Key ([TONE] Key)Key Mode “1” ([HM] Key: Default)Press this key momentarily to recall a favorite “Home” frequency memory.Press and hold in this for 1/2 second to activate Priority Channel Scanning.Key Mode “2” ([TONE] Key)Press this key momentarily to change the Tone Squelch mode: ENC (CTCSS Encoder),ENC.DEC (CTCSS Tone Squelch), or DCS (DCS) operation.FRONT PANEL CONTROLS & SWITCHESFCC ID: K66FT-8800RVertex Standard Co., Ltd.
15FT-8800R Operating Manual[SCN] Key ([SUB] Key)Key Mode “1” ([SCN] Key: Default)Press this key momentarily to activate the Scanner on the “Right” band.When the “Right” band is set to the Memory mode, press and hold in this key for 1/2second to set up the Scan Skip List or Preferential Scan List.Key Mode “2” ([SCN] Key)Press this key momentarily to make the next key you press act on the “Sub” band (the“” icon will blink on the “Sub” band).pVOLSQL Knob (Right)The inner VOL (Volume) control adjusts the speaker audio level from the “right” re-ceiver. Clockwise rotation increases the audio level.Press and hond in this knob for 2 seconds to turn the radio “on” and “off.”The outer SQL (Squelch) control is used to silence background noise on the “right”receiver. It should be advanced clockwise just to the point where the noise is silenced(and the “ ” indicator on the display turns off), so as to provide the best sensitivityto weak signals.qDIAL knob (Right)This 20-position detented rotary switch is the tuning dial for the “right” band.Press this knob momentarily to switch the “Main band” to be the “right” band.When the “right” band is set to be the “Main” band in the VFO mode, press this knob toenable rapid tuning (in 1 MHz steps) using this knob.Press and hold in this knob for 1/2 second to toggle the operating band on the “right”side as follows:430 MHz à  850 MHz à 144 MHz à 250 MHz à 350 MHz à 430 MHz ......FRONT PANEL CONTROLS & SWITCHESFCC ID: K66FT-8800RVertex Standard Co., Ltd.
16 FT-8800R Operating ManualLCD: Preferential Memory Channel: Skip Memory Channel: Minus Shiftt: Plus Shiftt: Odd Splitss: Tone Encoder: Tone Decoder: Transmission in Progress: “Main” Band: Busy Channel (or Squelch Off): Memory Tune Mode: Audio Mute Active: Digital Code Squelch (DCS): AM Reception: 9600 bps Packet Mode: Low TX Power Selected: Middle TX Power Selected: Automatic Power-Off Active: Keypad/DIAL Lock Active: Menu (“Set”) Mode: Key Function Mode is selected to “KEY-2”“Left” Band Memory Channel“Left” Band Frequency“Left” Band S- & PO Meter“Right” Band Frequency“Left” Band Memory Channel“Right” Band S- & PO MeterIconsFCC ID: K66FT-8800RVertex Standard Co., Ltd.
17FT-8800R Operating ManualjAntenna JackConnect your antenna here, using a type-M (PL-259) plug and coaxial cable.kDATA JackThis 6-pin mini-DIN connector provides simple interfacing to a packet Terminal NodeController (TNC) for 1200 bps or 9600 bps operation. The pin connections are shownon page 10.lEXT SP JackThis 2-conductor, 3.5-mm mini phone jack provides audio output for an optional speaker.The optimum load impedance is 8 Ohms. Inserting a plug into this jack disables theaudio path to the transceiver’s internal speaker.m13.8V DC Cable Pigtails w/FuseThis is the DC power supply connection for the transceiver. Use the supplied DC cableto connect this pigtail to the car battery or base station DC power supply capable of atleast 9 Amperes (continuous duty). Make certain that the Red lead connects to the Posi-tive (+) side of the power source, and that the Black lead connects to the Negative (-)side of the power source.REAR PANEL CONNECTIONS13.8VDCANTEXT SPDATAj klmFCC ID: K66FT-8800RVertex Standard Co., Ltd.
18 FT-8800R Operating ManualjPTT SwitchPress this switch to transmit, and release it to receive.kKeypadThese 16 keys generate DTMF tones during transmission.In the receive mode, these 16 keys can be used fordirect frequency entry and/or direct numeric recallof the Memory channels.l[P1]/[P2]/[P3]/[P4] Buttons[P1] button: Press this button to switch the “Main”band between the “Left” and “Right” displays on the LCDscreen. This is the best and easiest way to set the “Main” bandto the side you prefer.Pressing and holding in this button for 1/2 second moves op-eration to the next-highest frequency band on the “Main” band.[P2] button: Press this button momentarily to switch the frequencycontrol for the “Main” band between the VFO and Memory Systems.When the “Main” band is set to the VFO mode, press and hold in this button for 1/2 secondto activate the Smart Search Feature.When the “Main” band is set to the Memory mode, press and hold in this button for 1/2second to shift to the “Memory (offset) Tuning” feature.[P3] button: Pressing this button repeatedly allows selection of the CTCSS or DCS modeon the “Main” band. The selections available are:ENC à ENC.DEC (Tone Squelch) à DCS à OFF à ENC ......[P4] button: Press this button momentarily to select the transmitter power output level onthe “Main” band (“LOW,” “MID2,” “MID1,” or “HIGH”).When the “Main” band is set to the Memory mode or Home Channel, press and hold in thiskey for 1/2 second to switch the memory channel display between the “Frequency” formatand “Alpha-numeric Tag” format.You can reprogram the [P1], [P2], [P3], and [P4] buttons for other functions, if desired.See page 51 for details.mLAMP SwitchThis switch illuminates the Microphone keypad.nLOCK SwitchThis switch locks out the Microphone buttons (except for the keypad and PTT switch).o[UP]/[DWN] ButtonPress (or hold in) either of these buttons to tune (or scan up or down) the operatingfrequency or through the memory channels on the “Main” band. In many ways, thesebuttons emulate the function of the (rotary) “Main” band DIAL knob.DTMF MICROPHONEMH-48jklmnoMH-48A6J MICROPHONEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
19FT-8800R Operating ManualMH-42B6JS MICROPHONEThe MH-42B6JS is similar to the MH-48A6J, but the MH-42B6JS does not include a DTMFkeypad and its illumination switch.jPTT SwitchPress this switch to transmit, and release it to receive.k[ACC]/[P]/[P1]/[P2] Buttons[ACC] button: Press this button to switch the “Main”band between the “Left” and “Right” displays on theLCD screen. This is the best and easiest way to setthe “Main” band to the side you prefer.Pressing and holding in this button for 1/2 second movesoperation to the next-highest frequency band on the “Main”band.[P] button: Press this button momentarily to switch the fre-quency control for the “Main” band between the VFO andMemory Systems.When the “Main” band is set to the VFO mode, press and hold in thisbutton for 1/2 second to activate the Smart Search Feature.When the “Main” band is set to the Memory mode, press and hold inthis button for 1/2 second to shift to the “Memory (offset) Tuning” feature.[P2] button: Pressing this button repeatedly allows selection of the CTCSS or DCS modeon the “Main” band. The selections available are:ENC à ENC.DEC (Tone Squelch) à DCS à OFF à ENC ......[P3] button: Press this button momentarily to select the transmitter power output level onthe “Main” band (“LOW,” “MID2,” “MID1,” or “HIGH”).When the “Main” band is set to the Memory mode or Home Channel, press and hold in thiskey for 1/2 second to switch the memory channel display between the “Frequency” formatand “Alpha-numeric Tag” format.You can reprogram the [ACC], [P], [P1], and [P2] buttons for other functions, if desired.See page 51 for details.lLOCK SwitchThis switch locks out the Microphone buttons (except for the keypad and PTT switch).m[UP]/[DWN] ButtonPress (or hold in) either of these buttons to tune (or scan up or down) the operatingfrequency or through the memory channels on the “Main” band. In many ways, thesebuttons emulate the function of the (rotary) “Main” band DIAL knob.Notice: If you replace the microphone from the MH-48A6J to MH-42B6JS or viceversa, perform Menu #23 (MIC). See page 63 for details.CONDENSER  MICMH-42BjklmFCC ID: K66FT-8800RVertex Standard Co., Ltd.
20 FT-8800R Operating ManualHi! I’m R. F. Radio, and I’ll be helping you along as you learn the many featuresof the FT-8800R. I know you’re anxious to get on the air, but I encourage you toread the “Operation” section of this manual as thoroughly as possible, so you’ll get themost out of this fantastic new transceiver. Now. . .let’s get operating!TURNING THE TRANSCEIVER ON AND OFF1. To turn the transceiver on, press and hold in the “right”VOL knob for 2 seconds.When you turn on the FT-8900R, the current DC sup-ply voltage is indicated on the LCD for 2 seconds.After this interval, the display will switch its normalindication of the operating frequency.2. To turn the transceiver off, again press and hold in the “right” VOL knob for 2 seconds.ADJUSTING THE AUDIO VOLUME LEVELThe audio volume level is set independently for the “left” and “right” sides of the trans-ceiver. The “left” VOL knob provides adjustment for the “left” side of the FT-8800R, whilethe “right” VOL knob provides adjustment for the “right” side of the  FT-8800R.ADJUSTING THE SQUELCH SETTINGThe squelch is also set independently for the “left” and “right” sides of the transceiver. The“left” SQL knob provides adjustment for the “left” side of the  FT-8800R, while the “right”SQL knob provides adjustment for the “right” side of the FT-8800R.A special “RF Squelch” feature is provided on this radio. This feature allows you to set thesquelch so that only signals exceeding a certain S-meter level will open the squelch. Seepage 26 for detailsSELECTING THE OPERATING BANDIn the factory default configuration, The  FT-8800R operates in the “Dual Receive” mode.During Dual Receive operation, the “Main” band frequency ( on which transmission is pos-sible) will be indicated by the “ ” icon.To establish the “Main” band, simply press the microphone’s [P1] key (MH-48A6J, [ACC]key: MH-42B6JS), or press the DIAL knob for the “left” or “right” side momentarily, asappropriate. You will observe the “ ” icon lighting up alternate sides of the display asyou switch “Main” bands from the “left” side to the “right” side, and vice-versa.BASIC OPERATION465SQLVOLLOW V/M HM SCNKEY2PWRFCC ID: K66FT-8800RVertex Standard Co., Ltd.
21FT-8800R Operating ManualSELECTING THE FREQUENCY BANDPress and hold in the “left” DIAL knob to move the operating band on the “left” band144 MHz à 250 MHz à 350 MHz à 430 MHz à  850 MHz à 144 MHz ......Press and hold in the “right” DIAL knob to switch the operating band on the “right” band430 MHz à  850 MHz à 144 MHz à 250 MHz à 350 MHz à 430 MHz ......1) You may select the operating band on the “Main” band by pressing and holdingin the microphone’s [P1] key for 1/2 second.2) The FT-8800R may be configured to operate either in a V-V or U-U mode, if needed.BASIC OPERATIONVHF-VHF (V-V) Operation UHF-UHF (U-U) OperationFCC ID: K66FT-8800RVertex Standard Co., Ltd.
22 FT-8800R Operating ManualFREQUENCY NAVIGATION1) Tuning DialRotating the DIAL knob allows tuning in the pre-programmed steps established for the currentoperating band. Clockwise rotation of the DIAL knob causes the  FT-8800R to be tunedtoward a higher frequency, while counter-clockwise rotation will lower the operating frequency.On the “Main” band frequency, press the DIAL knob momentarily, then rotate the DIALknob, to change the “Main” band frequency steps to 1 MHz per step. This feature is ex-tremely useful for making rapid frequency excursions over the wide tuning range of the  FT-8800R.2) Direct Keypad Frequency Entry (MH-48A6J Microphone)The keypad of the MH-48A6J DTMF Microphone may be used for direct entry of the “Main”band operating frequency.To enter a frequency from the MH-48A6J keypad, just press the numbered digits in theproper sequence. There is no “decimal point” key on the MH-48A6J keypad.Examples:To enter 146.480 MHz, press [1] à [4] à [6] à [4] à [8] à [0]To enter 433.000 MHz, press [4] à [3] à [3] à [0] à [0] à [0]3) ScanningFrom the VFO mode, press the [SCN] key momentarily to initiate scanning toward a higherfrequency. The  FT-8800R will stop when it receives a signal strong enough to break throughthe squelch threshold. The  FT-8800R will then hold on that frequency according to thesetting of the “resume” mode (Menu #34 (SCAN); see page 65).If you wish to reverse the direction of the scan (i.e. toward a lower frequency, instead of ahigher frequency), just rotate the DIAL knob one click in the counter-clockwise directionwhile the  FT-8800R is scanning. The scanning direction will be reversed. To revert toscanning toward a higher frequency once more, rotate the DIAL knob one click clockwise.Press the [SCN] key again to cancel scanning.BASIC OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
23FT-8800R Operating ManualBASIC OPERATIONTRANSMISSIONTo transmit, simply close the PTT (Push To Talk) switch on the microphone.The  FT-8800R will transmit only on the “Main” band. During transmission, the “ ”icon will appear at the upper right of the “Main” frequency field on the display.Changing the Transmitter Power LevelYou can select from among a total of four transmit power levels on your  FT-8800R.To change the power level, press the [LOW] key to select one of four power settings. Thesepower levels will be stored, in memory registers, atthe time of memory storage (see page 32 for detailson Memory operation).During transmission, the Bar Graph will deflect in the display, according to the power out-put selected.You may change the power level on the “Main” band using the microphone’s [P4]key.LOW5 WMID 210 WMID 120 WHIGH50 W: 144 MHz35 W: 430 MHzFCC ID: K66FT-8800RVertex Standard Co., Ltd.
24 FT-8800R Operating ManualLOCK FEATUREIn order to prevent accidental frequency change, the panel switches and DIAL knobs may belocked out.To activate the Lock feature:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #21 (LOCK).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto change the setting to “ON.”4. Press the [SET] key momentarily to save the new setting and exit to normal operation.5. To unlock the panel switches and DIAL knobs, select “OFF” in step 3 above.KEYBOARD BEEPERA key/button beeper provides useful audible feedback whenever a key/button is pressed.If you want to turn the beep off:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #5 (BEEP).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto change the setting to “OFF.”4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.5. To back on again the beep, select “ON” in step 3 above.CHANNEL STEP SELECTIONThe FT-8800R’s synthesizer provides the option of utilizing channel steps of 5/10/12.5/15/20/25/50 kHz per step, any number of which may be important to your operating require-ments. The FT-8800R is set up at the factory with different default steps on each operatingband which probably are satisfactory for most operation. However, if you need to change thechannel step increments, the procedure to do so is very easy; remember to get set up on thedesired band before making any changes, as different steps may be programmed for eachoperating band.1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #38 (STEP).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the new channel step size.4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.ADVANCED OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
25FT-8800R Operating ManualDISPLAY BRIGHTNESSThe FT-8800R display illumination has been specially engineered to provide high visibilitywith minimal disruption of your “night vision” while you are driving. The brightness of thedisplay is manually adjustable, using following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #9 (DIMMER).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select a comfortable brightness level: DIM 1, DIM 2, DIM 3, or DIM.OFF (no illumi-nation).4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.BAND LINKINGFor operation on Amateur satellites which use a “normal” (not “inverted”) FM transponder,the Band Link feature may be useful.1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #43 (VFO.TR).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto change the setting to “ON.”4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.As you rotate the “Main” band DIAL, you will observe that both bands’ frequencies arechanging together. When you are done with this operating mode, select “OFF” in step 3above.ADVANCED OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
26 FT-8800R Operating ManualADVANCED OPERATIONAUDIO MUTINGThe Audio Mute feature is useful in situation where it would be helpful to reduce the audiolevel of the “Receive Only” band whenever you receive a signal on the “Main” band or youtransmit on the “Main” band during Dual Receive operation.To activate the Audio Mute feature:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #24 (MUTE).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto choose the desired selection.TX:Reduces the audio level of the “Receive Only” band whenever you transmit onthe “Main” bandRX:Reduces the audio level of the “Receive Only” band whenever you receive asignal on the “Main” band.TX/RX:Reduces the audio level of the “Receive Only” band whenever you receive asignal on the “Main” band or you transmit on the “Main” bandOFF:Disables the Audio Mute feature4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.RF SQUELCHA special “RF Squelch” feature is provided on this radio. This feature allows you to set thesquelch so that only signals exceeding a certain S-meter level will open the squelch.When setting up the RF Squelch circuit for operation, note that you may set the RF Squelchindependently for the “left” and “right” sides, using the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #32 (RF SQL).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired signal strength level for the squelch threshold (OFF, S-2, S-5, S-9, orS-FULL).4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.5. Finally, rotate the SQL knob fully clockwise.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
27FT-8800R Operating ManualRepeater stations, usually located on mountaintops or other high locations, provide a dra-matic extension of the communication range for low-powered hand-held or mobile trans-ceivers. The FT-8800R includes a number of features which make repeater operation simpleand enjoyable.REPEATER SHIFTSYour FT-8800R has been configured, at the factory, for the repeater shifts customary inyour country. While the 144 MHz shift will be 600 kHz; on 70 cm, the shift may be 1.6 MHz,7.6 MHz, or 5 MHz (USA version).Depending on the part of the band in which you are operating, the repeater shift may beeither downward (–) or upward (+), and one of these icons will appear at the bottom of theLCD when repeater shifts have been enabled.AUTOMATIC REPEATER SHIFT (ARS)The FT-8800R provides a convenient Automatic Repeater Shift feature, which causes theappropriate repeater shift to be automatically applied whenever you tune into the designatedrepeater sub-bands in your country. These sub-bands are shown below.If the ARS feature does not appear to be working, you may have accidentally disabled it.To re-enable ARS:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #2 (ARS).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto change the setting to “ON” (to enable Automatic Repeater Shift).4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.REPEATER OPERATIONEuropean VersionVersion A2-m145.1 145.5145.6 145.8146.0 146.4 147.0 147.6 148.0146.6 147.4Euro Version 1Euro Version 2Version A70-cm440.0445.0450.0439.45438.20433.00 433.40ARS-Repeater SubbandsFCC ID: K66FT-8800RVertex Standard Co., Ltd.
28 FT-8800R Operating ManualMANUAL REPEATER SHIFT ACTIVATIONIf the ARS feature has been disabled, or if you need to set a repeater shift direction otherthan that established by the ARS, you may set the direction of the repeater shift manually.To do this:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #33 (RPT.MOD).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired shift among “–,” “+,” and “OFF.”4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.Changing the Default Repeater ShiftsIf you travel to a different region, you may need to change the default repeater shift so as toensure compatibility with local operating requirements.To do this, follow the procedure below:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #36 (SHIFT).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the new repeater shift magnitude.4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.If you just have one “odd” split that you need to program, don’t change the “de-fault” repeated shifts using this Menu Item! Enter the transmit and receive fre-quencies separately, as shown on page 33.REPEATER OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
29FT-8800R Operating ManualCTCSS OPERATIONMany repeater systems require that a very-low-frequency audio tone be superimposed onyour FM carrier in order to activate the repeater. This helps prevent false activation of therepeater by radar or spurious signals from other transmitters. This tone system, called“CTCSS” (Continuous Tone Coded Squelch System), is included in your FT-8800R, and isvery easy to activate.CTCSS setup involves two actions: setting the Tone Mode and then setting of theTone Frequency. These actions are set up by using the Set mode #41 (TONE M)and #40 (TONE F).1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #41 (TONE M).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobso that “ENC” appears on the display; this activates the CTCSS Encoder, which allowsrepeater access.You may notice an additional “DCS” icon appearing while you rotate the“Main” band DIAL knob in this step. We’ll discuss the Digital Code Squelchsystem shortly.4. Rotating the “Main” band DIAL knob one more click clockwise in step “3” above willcause “ENC.DEC” to appear. When “ENC.DEC” appears, this means that the Tone Squelchsystem is active, which mutes your FT-8800R’s receiver until it receives a call fromanother radio sending out a matching CTCSS tone. This can help keep your radio quietuntil a specific call is received, which may be helpful while operating in congested areas.5. When you have made your selection of theCTCSS tone mode, press the “Main” bandDIAL knob momentarily, then rotate the“Main” band DIAL knob one click counter-clockwise to select Menu #40 (TONE F).This Menu selection allows setting of theCTCSS tone frequency to be used.6. Press “Main” band DIAL knob momentarilyto enable adjustment of the CTCSS fre-quency.7. Rotate the “Main” band DIAL knob until the display indicates the Tone Frequency youneed to be using.8. When you have made your selection, press and hold in the “Main” band DIAL knob for1/2 second to save the new setting and exit to normal operation.CTCSS/DCS OPERATIONCTCSS TONE FREQUENCY (Hz)  67.0   69.3   71.9   74.4   77.0   79.7  82.5   85.4   88.5   91.5   94.8   97.4100.0 103.5 107.2 110.9 114.8 118.8123.0 127.3 131.8 136.5 141.3 146.2151.4 156.7 159.8 162.2 165.5 167.9171.3 173.8 177.3 179.9 183.5 186.2189.9 192.8 196.6 199.5 203.5 206.5210.7 218.1 225.7 229.1 233.6 241.8250.3 254.1 ––––FCC ID: K66FT-8800RVertex Standard Co., Ltd.
30 FT-8800R Operating ManualCTCSS/DCS OPERATION1) Your repeater may or may not re-transmit a CTCSS tone - some systems just useCTCSS to control access to the repeater, but don’t pass it along when transmitting.If the S-Meter deflects, but the FT-8800R is not passing audio, repeat steps “1” through“4” above, but rotate the “Main” DIAL knob so that “ENC” appears - this will allow youto hear all traffic on the channel being received.2) You may select the Tone Squelch mode (ENC, ENC.DEC, or DCS) on the “Main”band by the microphone’s [P3] key.DCS OPERATIONAnother form of tone access control is Digital Code Squelch, or DCS. It is a newer, moreadvanced tone system which generally provides more immunity from false paging than doesCTCSS. The DCS Encoder/Decoder is built into your FT-8800R, and operation is verysimilar to that just described for CTCSS. Your repeater system may be configured for DCS;if not, it is frequently quite useful in Simplex operation if your friend(s) use transceiversequipped with this advanced feature.Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCS andthat you select a tone code.1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #40 (TONE M).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobuntil “DCS” appears on the display; this activates the DCS Encoder/Decoder.4. Now, press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIALknob to select Menu #10 (DCS.COD).5. Press the “Main” band DIAL knob momen-tarily to enable the adjustment of the DCScode.6. Rotate the “Main” band DIAL knob to se-lect the desired DCS Code (a three-digitnumber).7. When you have made your selection, pressand hold in the “Main” band DIAL knob for1/2 second to save the new setting and exitto normal operation.1) Remember that the DCS is an Encode/Decode system, so your receiver willremain muted until a matching DCS code is received on an incoming transmis-sion. Switch the DCS off when you’re just tuning around the band!2) You may select the DCS mode on the “Main” band by the microphone’s [P3] key.CTCSS OPERATIONDCS CODE023 025 026 031 032 036 043 047 051 053054 065 071 072 073 074 114 115 116 122125 131 132 134 143 145 152 155 156 162165 172 174 205 212 223 225 226 243 244245 246 251 252 255 261 263 265 266 271274 306 311 315 325 331 332 343 346 351356 364 365 371 411 412 413 423 431 432445 446 452 454 455 462 464 465 466 503506 516 523 526 532 546 565 606 612 624627 631 632 654 662 664 703 712 723 731732 734 743 754 – – – – – –FCC ID: K66FT-8800RVertex Standard Co., Ltd.
31FT-8800R Operating ManualTONE SEARCH SCANNINGIn operating situations where you don’t know the CTCSS or DCS tone being used by an-other station or stations, you can command the radio to listen to the incoming signal andscan in search of the tone being used. Two things must be remembered in this regard:¦You must be sure that your repeater uses the same tone type (CTCSS vs. DCS).¦Some repeaters do not pass the CTCSS tone; you may have to listen to the station(s)transmitting on the repeater uplink (input) frequency in order to allow Tone Search Scan-ning to work.To scan for the tone in use:1. Set the radio up for either CTCSS or DCS Decoder operation (see the previous discus-sion). In the case of CTCSS, “ENC DEC” will appear on the display; in the case of DCS,“DCS” will appear on the display.2. Press the [SET] key momentarily to enter the Set mode.3. Rotate the “Main” band DIAL knob to select Menu #40 (TONE F) when CTCSS is se-lected, or Menu #10 (DCS.COD) during DCS operation.4. Press the “Main” band DIAL knob to enable adjustment of the selected Menu Item.5. Press the “Main” band [SCN] key momentarily to start scanning for the incoming CTCSSor DCS tone/code.6. When the radio detects the correct tone or code, it will halt on that tone/code, and audiowill be allowed to pass. Press the “Main” band DIAL knob momentarily to lock in thattone/code, then press and hold in the “Main” band DIAL knob for 1/2 second to save thenew setting and exit to normal operation.If the Tone Scan feature does not detect a tone or code, it will continue to scanindefinitely. When this happens, it may be that the other station is not sending anytone. You can press the [SCN] key to halt the scan at any time.Tone Scanning works either in the VFO or Memory modes.CTCSS/DCS OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
32 FT-8800R Operating ManualThe FT-8800R provides a wide variety of memory system resources. These include:rIndependent Regular Memory Channels for the “Main” and “Sub” bands, which madeup of:¦512 “Standard” memory channels, numbered “001” through “512.”¦Five Home channels, providing storage and quick recall of one prime frequency oneach operating band.¦Ten sets of band-edge memories also known as “Programmable Memory Scan” chan-nels, labeled “L1/U1” through “L10/U10.”¦Ten Memory Banks, labeled “BANK1” through “BANK10.”rSix “Hyper-Memory” ChannelsMEMORY OPERATIONREGULAR MEMORY CHANNEL OPERATIONMemory Storage1. Select the desired frequency, while operating in the VFO mode on the “Main” band. Besure set up any desired CTCSS or DCS tones, as well as any desired repeater offset. Thepower level may be also be set at this time, if you wish to store it.2. Press and hold in the [SET] key for 1/2 second. A memory number will appear (blink-ing) on the display.3. Within ten seconds of pressing the [SET] key, use the “Main” band DIAL knob or themicrophone’s [UP]/[DWN] buttons to select the desired memory channel for storage (ifthe channel is already occupied by data stored previously, the “channel frequency” nota-tion will appear on the display.4. To attach an alpha/numeric name “Tag” to the memory, press and hold in the [SET] keyfor 1/2 second, then proceed to the next step; otherwise press the [SET] key momen-tarily to save the entry and exit to normal operation.HOME Channels(5 channels) HOME Channels(5 channels)L10/U10L10/U10L9/U9L9/U9L3/U3L3/U3L2/U2L2/U2L1/U1L1/U1512512511511004004003003002002001001Standard Memory Channels(512 channels) Standard Memory Channels(512 channels)PMS Memory Channels(10 Sets) PMS Memory Channels(10 Sets)1-HP2-HP3-HP4-HP5-HP6-HP850 MHz Band430 MHz Band250 MHz Band350 MHz Band144 MHz Band850 MHz Band430 MHz Band250 MHz Band350 MHz Band144 MHz BandRegular Memory Channels ( Band)LeftRegular Memory Channels ( Band)RightHyper Memory Channels (6 channels)FCC ID: K66FT-8800RVertex Standard Co., Ltd.
33FT-8800R Operating ManualTo Append an Alpha-numeric “Tag” to a Memory1. After press and holding in the [SET] key in step 4 above, rotate the “Main” band DIALknob to select the first character in the name you wish to store, the press the “Main” bandDIAL knob momentarily to move on to the next character. Letters, numbers, and sym-bols are available for storage.2. Again rotate the “Main” band DIAL knob to select the desired letter, number, or symbol,then press the “Main” band DIAL knob momentarily to move on to the next character’sslot.If you make a mistake, press the microphone’s [DWN] button to move back to the previ-ous character’s slot, then re-select the correct letter, number, or symbol.3. Repeat the above step to program the remaining letters, numbers, or symbols of thedesired label. A total of six characters may be used in the creation of a label.4. When you have completed the creation of the label, press the [SET] key momentarily tosave the label and exit to normal operation.Storing Independent Transmit Frequencies (“Odd Splits”)1. Store the receiving frequency using the method already described.2. Turn to the desired transmit frequency on the “Main” band, then press and hold in the[SET] key for 1/2 second.3. Within ten seconds of pressing the [SET] key, use the “Main” band DIAL knob ormicrophone’s [UP]/[DWN] buttons to select the same memory channel number as usedin step 1 above.4. Press and hold in the PTT switch, then press the [SET] key momentarily while holdingthe PTT switch to save the entry and exit to normal operation. This will not cause trans-mission; instead, it signals the microprocessor that a separate transmit frequency is be-ing programmed into that memory register.Whenever you recall a memory which contains independently-stored transmit andreceive frequencies, the “[ ]” indication will appear in the display..MEMORY OPERATIONREGULAR MEMORY CHANNEL OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
34 FT-8800R Operating ManualMemory Recall1. While operating in the VFO mode, press the [V/M] key momentarily to enter the Memorymode.2. Rotate the DIAL knob to select the desired channel.3. To return to the VFO mode, press the [V/M] key momentarily again.When the radio is already set to the Memory mode, an easy way to recall memoriesis to enter the microphone’s key in the memory channel number. For example, torecall memory channel #4, press [0] à [0] à [4].Memory Offset TuningOnce you have recalled a particular memory channel, you may easily tune off that channel,as though you were in the “VFO” mode.1. With the FT-8800R in the “MR” (Memory Recall) mode, select the desired memorychannel.2. Now press and hold in the [V/M] key for 1/2 second; the “MT” icon will appear on thedisplay.3. Rotate the DIAL knob, as desired, to tune to a new frequency. The synthesizer stepsselected for VFO operation on the current band will be the steps used during MemoryTuning.4. Press and hold in the [V/M] key for 1/2 second during Memory Tuning, the data will nowhave been copied to VFO, although the original memory contents will remain intact onthe previously-stored channel.5. If you wish to return to the original memory frequency, press and hold in the [V/M] keyfor 1/2 second. The “MT” icon will disappear.Deleting MemoriesWith 808 total memories available, there frequently are situations where you may desire todelete certain memorized frequencies. The procedure for deleting a channel is quite simple:1. Press the [V/M] key, if needed, to enter the Memory mode.2. Press and hold in the [SET] key for 1/2 second, then rotate the “Main” band DIAL knobto select the memory channel to be deleted. Note that memory channel #1 may not bedeleted.3. Press the “Main” band [SCN] key momentarily. The display will revert to memory chan-nel #1. If you rotate the “Main” band DIAL knob to the location you just “Masked,” youwill observe that it is now invisible.Note: One deleted, the channel data cannot be recovered.MEMORY OPERATIONREGULAR MEMORY CHANNEL OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
35FT-8800R Operating ManualHOME Channel MemoryA special one-touch “HOME” channel is available (one for each of the five operating bands:see page 21), to allow quick recall of a favorite operating frequency on each band. Memorystorage is simple to accomplish:1. Select the desired frequency, while operating in the VFO mode on the “Main” band. Besure to set up any desired CTCSS or DCS tones, as well as any desired repeater offset.The power level may also be set at this time, if you wish to store it.2. Press and hold in the [SET] key for 1/2 second. A memory number will appear (blink-ing) on the display.3. While the memory channel number is blinking, just press the “Main” [H/M] key. Thefrequency and other data (if any) will now be stored in the special HOME channel regis-ter.4. You may repeat this process on the other operating bands.5. To recall the HOME channel, just press the [H/M] key while operating either in the VFOor MR mode.MEMORY OPERATIONREGULAR MEMORY CHANNEL OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
36 FT-8800R Operating ManualMEMORY OPERATIONMemory Bank OperationMemory Bank Assignment1. Recall the memory channel to be assigned to a Memory Bank.2. Press and hold in the [V/M] key for 1/2 seconds, then rotate the “Main” band DIAL knobto select the Memory Bank (“BANK1” ~ “BANK10” ) you want as the Memory Bankfor this channel.3. Press and hold in the [SET] key for 1/2 seconds to copy the memory channel data intothe Memory Bank.Memory Bank Recall1. Set the radio to the Memory mode by pressing the [V/M] key, if necessary.2. Press and hold in the [V/M] key for 1/2 seconds, then rotate the “Main” band DIAL knobto select the Memory Bank (“BANK1” ~ “BANK10” ).3. Press the [SET key momentarily to lock in the selected Memory Bank.4. In the Memory Bank mode of operation, you can only select memory channels in thecurrent memory bank.5. To change the Memory Bank to another Bank, press and hold in the [V/M] key for 1/2seconds, then rotate the “Main” band DIAL knob.6. To exit from Memory Bank operation, press and hold in the [V/M] key for 1/2 seconds,then rotate the “Main” band DIAL knob to select “ALL press and hold in the [V/M] keyfor 1/2 seconds, then rotate the “Main” band DIAL knob to select “ALL.MEM.”Delete the Memory Channel from the Memory Bank1. In the Memory Bank mode, recall the memory channel to be deleted from the MemoryBank.2. Press and hold in the [V/M] key for 1/2 seconds, then press and hold in the [V/M] key for1/2 seconds again to delete the Memory Channel from the Memory Bank.Memory Only ModeOnce memory channel programming has been completed, you may place the radio in a“Memory Only” mode, whereby VFO operation is impossible. This may be particularlyuseful during public-service events where a number of operators may be using the radio forfirst time, and ultimate simplicity of channel selection is desired.To place the radio into the Memory Only mode:1. Turn the radio off.2. Press and hold in the “left” [V/M] key while turning the radio on.3. Rotate the “right” DIAL knob to select the (F-5 M-ONLY MODE), then press the [SET]key momentarily.To return to normal operation, repeat the above steps.REGULAR MEMORY CHANNEL OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
37FT-8800R Operating ManualHYPER MEMORY MODEThe FT-8800R usually stores, into memory, the operating frequency and some aspects ofoperating status (such as CTCSS/DCS data, repeater shift, power level etc.). However, the“Hyper Memory” Mode allows you to store the total current configuration of the radio intoa special “Hyper” memory bank.For example, a Hyper Memory location may store the frequencies of both the “Left” and“right” bands, plus Scanning features, etc.Hyper Memory Storage1. Set up the transceiver according to the desired configuration.2. Press and hold in the Hyper Memory key ([1] through [6]), corresponding to the HyperMemory channel into which you wish to store this configuration, for 2 seconds.Hyper Memory RecallPress the appropriate Hyper Memory key ([1] through [6]) to recall the desired Hyper Memorychannel.The current (original) configuration will lost when you recall the Hyper MemoryChannel. To prevent this from happening, press and hold in the Hyper Memorykey (generally the [1] key) to store the current configuration into that Hyper MemoryChannel before recalling the Hyper Memory Channel, or set Menu #16 to enable theAutomatic Writing feature for the Hyper Memory. See page 62 for details.MEMORY OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
38 FT-8800R Operating ManualThe FT-8800R allows you to scan just the memory channels, the entire operating band, ora portion of that band. It will halt on signals encountered, so you can talk to the station(s) onthat frequency, if you like.Scanning operation is basically the same in each of the above modes. Before you begin, takea moment to select the way in which you would like the scanner to resume scanning after ithalts on a signal.Setting the Scan-Resume TechniqueTwo options for the Scan-Resume mode are available:TIME:In this mode, the scanner will halt on a signal it encounters, and will hold there forfive seconds. If you do not take action to disable the scanner within five seconds, thescanner will resume even if the stations are still active.BUSY:In this mode, the scanner will halt on a signal it encounters. Two seconds after thecarrier has dropped because the other station(s) ceased transmission, the scannerwill resume.To set the Scan-Resume mode:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #34 (SCAN).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired scan-resume mode.4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.Note: The default condition for this Menu Item is “TIME.”SCANNINGFCC ID: K66FT-8800RVertex Standard Co., Ltd.
39FT-8800R Operating ManualVFO SCANNINGThis mode allows you to scan the entire current operating band.1. Select the VFO mode by pressing the [V/M] key, if necessary.2. Press and hold in the [SCN] key for one second, then rotate the DIAL knob to select thebandwidth for the VFO scanner. Available selections are ±1 MHz, ±2 MHz, ±5 MHz,ALL, and PMS-X.ALL: The scanner will sweep all frequencies between 108 - 520 MHz and 700 -999.990 MHz.PMS-X: The scanner will sweep frequencies within the currently-selected PMS frequencypair. See page 41 for details.3. Press the [SCN] key momentarily to start scanning.4.If and when the scanner encounters a signal strong enough to open the squelch, thescanner will halt temporarily; the decimal point of the frequency display will blink dur-ing this “Pause” condition.5.The scanner will then resume according to the Scan-Resume mode selected in the previ-ous section.6.To cancel scanning, press the [SCN] key momentarily again (or press the microphone’sPTT key).1) When you start scanning, the FT-8800R will be changing frequency in theupward direction. If you want to change direction of the scan while it is underway,rotate the DIAL knob one click in the opposite direction (in this case, one click counter-clockwise). You’ll see the scanner turn around and change frequency downward!2) Press and hold the microphones [UP]/[DWN] key, the scanner will sweep frequenciesonly on the current band. In this mode, you may change the scanning function so that theVFO frequency will jump to the low band edge of the next band when the VFO frequencyreaches the high edge of the current band (or vice versa). See page 60 regarding Menu #4(BAND).SCANNINGFCC ID: K66FT-8800RVertex Standard Co., Ltd.
40 FT-8800R Operating ManualMEMORY SCANNINGMemory scanning is similarly easy to initiate:1. Set the radio to the Memory mode by pressing the [V/M] key, if necessary.2. Press the [SCN] key to initiate scanning.3. As with VFO scanning, the scanner will halt on any signal encountered that is strongenough to open the squelch; it will then resume scanning according to the Scan-Resumemode set previously.4. To cancel scanning, press the [SCN] key again (or press the microphone’s PTT key).How to Skip (Omit) a Channel During Memory Scan OperationSome continuous-carrier stations like a Weather Broadcast station will seriously impedescanner operation if you are using the “Carrier Drop” Scan-Resume mode, as the incomingsignal will not pause long enough for the transceiver to resume scanning. Such channels maybe “Skipped” during scanning, if you like:Here is the procedure for setting up and using the Memory Channel Skip Scan:1. Set the radio to the Memory Mode by pressing the [V/M] key, if necessary.2. Rotate the DIAL knob to select the Memory Channel to be skipped during scanning.3. Press and hold the [SCN] key for 1/2 second so as to make the small “SKIP” icon appearon the display. The current Memory Channel will now be ignored during scanning. Thesmall “SKIP” icon will also appear when you recall the “skipped” memory channel manu-ally.The “t” selection is used for “Preferential Memory Scan,” described in thenext column.4. To re-institute a channel into the scanning loop, press and hold in the [SCN] key for1/2 second twice to select “OFF” (the “Skipped” channel will, of course, still be acces-sible via manual channel selection methods using the DIAL knob in the MR mode, whetheror not it is locked out of the scanning loop).To initiate the Memory Channel Skip Scan:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #37 (SKP.MSM).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto “SKIP.”4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.5. Now, press the [SCN] key momentarily to initiate Memory Channels Skips Scan. Thechannels which have the “SKIP” icon appended to the channel number will be ignoredduring scanning.6. To cancel the Memory Channels Skips Scan, select “OFF” in step 3 above.SCANNINGFCC ID: K66FT-8800RVertex Standard Co., Ltd.
41FT-8800R Operating ManualPreferential Memory ScanThe FT-8800R also allows you to set up a “Preferential Scan List” of channels which youcan “flag” within the memory system. These channels are designated by a “t” icon whenyou have selected them, one by one, for the Preferential Scan List.When you initiate memory scanning, beginning on a channel with the “t” icon appended,only those channels bearing the “t” icon will be scanned. If you initiate scanning on achannel which does not have the “t” icon appended, you will scan all channels includingthose with the “t” icon appended.Here is the procedure for setting up and using the Preferential Scan List:1. Press the [V/M] key momentarily to enter the Memory Recall mode, if you are not usingmemories already.2. Rotate the DIAL knob to select the channel which you wish to add to the PreferentialScan List.3. Press and hold the [SCN] key for 1/2 second, several times if necessary, so as to makethe “t” icon appear by the channel designator.To initiate Preferential Memory Scan:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #37 (SKP.MSM).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto “MSM.”4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.5. Now, press the [SCN] key momentarily to initiate Preferential Memory Scanning. Onlythe channels which have the “t” icon appended to the channel number will be scanned.6. To cancel the Preferential Memory Scanning, select “OFF” in step 3 above.SCANNINGMEMORY SCANNINGFCC ID: K66FT-8800RVertex Standard Co., Ltd.
42 FT-8800R Operating ManualPROGRAMMABLE (BAND LIMIT) MEMORY SCAN (PMS)This feature allows you to set sub-band limits for either scanning or manual VFO operation.For example, you might with to set up a limit (in North America) of 144.300 MHz to 148.000MHz so as to prevent encroachment into the SSB/CW “Weak Signal” portion of the bandbelow 144.300 MHz. Here’s how to do this:1. Set the radio to the VFO mode by pressing the [V/M] key, if necessary.2. Using the techniques learned earlier, store 144.300 MHz into Memory Channel #L1 (the“L” designates the Lower sub-band limit).3. Likewise, store 148.000 MHz into Memory Channel #U1 (the “U” designates the Uppersub-band limit).4. Switch to the Memory mode by pressing the [V/M] key once, then rotate the DIAL knobto select Memory Channel # L1.5. Press and hold in the [V/M] key for 1/2 second to start PMS operation; the “MT” labelwill be appears on the display. Tuning and canning will now be limited within the just-programmed range.6. Ten pairs of Band Limit memories, labeled L1/U1 through L10/U10 are available. Youtherefore can set upper and lower operation limits on a number of bands, if you like.SCANNINGFCC ID: K66FT-8800RVertex Standard Co., Ltd.
43FT-8800R Operating ManualSCANNING“PRIORITY CHANNEL” SCANNING (DUAL WATCH)The FT-8800R’s scanning features include a two-channel scanning capability which allowsyou to operate on a VFO, Memory channel, or Home channel, while periodically checking auser-defined “Priority” Memory Channel for activity. If a station is received on the “Prior-ity” Channel which is strong enough to open the Squelch, the scanner will pause on thatstation in accordance with the Scan-Resume mode set via Set mode [Menu #34 (SCAN)].See page 37.Here is the procedure for activating Priority Channel Dual Watch operation:VFO Priority1. Recall the memory channel you wish to use as the “priority” frequency.2. Now set the FT-8800R for operation on a VFO frequency.3. Press and hold in the [HM] key for 1/2 second to activate the VFO Priority mode. Thedisplay will remain on the VFO frequency, but every five seconds the FT-8800R willcheck the Priority Channel (memory channel) for activity.4. Press the [V/M] key to disable the VFO Priority mode and exit to regular VFO operation.Memory Priority1. Store the frequency you wish to be the “Priority” Channel into memory channel “1.”2. Now set the FT-8800R for operation on another memory channel.3. Press and hold in the [HM] key for 1/2 second to activate the Memory Priority mode.The display will remain on the current memory channel frequency, but every five sec-onds the FT-8800R will check the Priority Channel (memory channel “1”) for activity.4. Press the [V/M] key to disable the Memory Priority mode and exit to regular memoryoperation.HOME Priority1. Recall the memory channel you wish to use as the “priority” frequency.2. Now set the FT-8800R for operation on a HOME channel.3. Press and hold in the [HM] key for 1/2 second to activate the HOME Priority mode. Thedisplay will remain on the HOME channel frequency, but every five seconds the FT-8800R will check the Priority Channel (memory channel) for activity.4. Press the [V/M] key to disable the HOME Priority mode and exit to regular VFO opera-tion.You may operate individual Priority Channel Dual Watch features on both bandsat the same time, such as having the VFO Priority mode engaged on the “right”band and the Memory Priority mode engaged on the “left” band.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
44 FT-8800R Operating ManualThe Smart Search feature may be used to load - automatically with no operator intervention- a special bank of up to 25 memory channels (per band) on activity.The Smart Search function will sweep the entire band, and will load the special memorybank with the frequency and repeater shift data pertaining to those channels on which activ-ity is found (if Automatic Repeater Shift is activated). The channels are loaded in order inwhich they are encountered, not according to signal strength or by ascending frequency.The Smart Search feature is especially useful when visiting a city for the first time, whereyou may be unfamiliar with the repeater frequencies; Smart Search discovers where thelocal activity is to be found, and automatically loads those frequencies for you.Smart Search operation is simple to activate:1. Set the radio to the VFO mode by pressing the [V/M] key, if necessary.2. Press and hold in the [V/M] key; this will cause the radio to scan upward on the currentband, loading channels on which it encounters a signal strong enough to open the squelch.3. When 25 channels are loaded, or when the scanner reaches the band edge, the scannerwill stop and the transceiver will revert to the starting frequency.4. To recall the Smart Search memories just stored, rotate the DIAL knob or press themicrophone’s [UP]/[DWN] keys (for the “Main” band Smart Search memories only).5. If you found particular channels which you wish to store into the “regular” memorychannel, follow the memory storage procedures described on page 32.1) The Smart Search memories are so-called “soft” memories; they will lost if youexit the Smart Search mode or initiate a new Smart Search sweep.2) You may activate the Smart Search operation on the “Main” band by press and holdthe microphone’s [P2] key.3) You may activate the Smart Search operation on the “left” and “right” bands at thesame time.SMART SEARCHFCC ID: K66FT-8800RVertex Standard Co., Ltd.
45FT-8800R Operating ManualNOTEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
46 FT-8800R Operating ManualThe ARTS feature uses DCS signaling to inform both parties when you and another ARTS-equipped station are within communications range. This may be particularly useful duringSearch-and Rescue situations, where is important to stay in contact with other members ofyour group.Both stations must set up their DCS codes to the same code number, then activate theirARTS feature using the command appropriate for their radio. Alert ringers may be activated,if desired.Whenever you push the PTT switch, or every 25 seconds after ARTS is activated, your radiowill transmit a signal which includes a (subaudible) DCS signal for about one second. If theother radio is in range, the beeper will sound (if enabled) and the display will show “IN.RNG”as opposed to the out of range display “OUT.RNG” in which ARTS operation begins.Whether you talk or not, the polling every 25 seconds will continue until you de-activateARTS. Every 10 minutes, moreover, you can have your radio transmit your callsign via CW,so as to comply with identification requirements. When ARTS is de-activated, DCS will alsobe deactivated (if you were not using it previously in non-ARTS operation).If you move out of range for more than one minute (four pollings), your radio will sense thatno signal has been received, three beeps will sound, and the display will revert to “OUT.RNG.”If you move back into range, your radio will again beep, and the display will change back tothe “IN.RNG” indication.During ARTS operation, it is not possible to change the operating frequency or other set-tings on the “Main” band; you must terminate ARTS in order to resume normal operation.This is a safety feature designed to prevent accidental loss of contact due to channel change,etc. Here is how to activate ARTS:Basic ARTS Setup and Operation1. Set your radio and the other radio(s) to the same DCS code number, per the discussionon page 30.2. Press the [SET] key momentarily to enter the Set mode.3. Rotate the “Main” band DIAL knob to select Menu #3 (ARTS).4. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired ARTS beep option. The available options are:IN.RNG:The beeps are issued only when the radio first confirms that you are withinrange, but does not re-confirm with beeps thereafter.OUT.RNG:Every time a polling transmission is received from the other station, the alertbeeps will be heard.5. Press the “Main” band DIAL knob momentarily. You will observe the “OUT.RNG” dis-play on the LCD. ARTS operation has now commenced.6.Every 25 seconds, your radio will transmit a “polling” call to the other station. When thatARTSTM: AUTO RANGE TRANSPONDER SYSTEMFCC ID: K66FT-8800RVertex Standard Co., Ltd.
47FT-8800R Operating Manualstation responds with its own ARTS polling signal, the display will change to “IN.RNG”to confirm that the other station’s polling code was received in response to yours.7.Press the “Main” band DIAL knob momentarily to exit ARTS operation and resumenormal functioning of the transceiver.CW Identifier SetupThe ARTS feature includes a CW identifier, as discussed previously. Every ten minutesduring ARTS operation, the radio can be instructed to send “DE (your callsign) K” if thisfeature is enabled. The callsign field may contain up to 6 characters.Here’s how to program the CW Identifier:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #8 (CWID W).3. Press the “Main” band DIAL knob momentarily.4. Press the “Main” band DIAL knob momentarily again to enable entry of your callsign.5. Rotate the “Main” band DIAL knob one click clockwise to begin entry of the letters andnumbers in your callsign.6. Press the “Main” band DIAL knob momentarily to set the first letter or number in yourcallsign.7. When the correct character has been selected, Press the “Main” band DIAL knob mo-mentarily to move on to the next character.8. Repeat steps 6 and 7 as many times as necessary to complete your callsign.9. Press the “Main” [SCN] key to delete all data after the cursor that may have been previ-ously stored (erroneously).10.When you have entered your entire callsign, press the “Main” band DIAL knob momen-tarily to confirm the callsign.11. Press the [SET] key momentarily, then rotate the “Main” band DIAL knob one clickcounter-clockwise to select the Menu #7 (CWID).12.Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select “TX ON” (to enable the CW identifier).13.Press the “Main” band DIAL knob momentarily to save the setting and exit to normaloperation.ARTSTM: AUTO RANGE TRANSPONDER SYSTEMFCC ID: K66FT-8800RVertex Standard Co., Ltd.
48 FT-8800R Operating Manual16 DTMF Autodialer memories are available on the FT-8800R. These DTMF Autodialermemories can store up to 16 digits of a telephone number for, repeater autopatch or otheruses.To load DTMF Autodialer memories, use following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #15 (DTMF W).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the DTMF Autodialer memory channel number (“d-1” through “d-16”) intowhich you wish store a telephone number.4. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the first digit of the telephone number you wish to store.5. When you have selected the correct digit, press the “Main” band DIAL knob momen-tarily. Now, rotate the “Main” band DIAL knob to select the second of the 16 availablenumbers in this current DTMF Audodialer memory register.6. Repeat this procedure for each digit in the telephone number. Press the “Main” band[SET] key momentarily to delete any previously-stored data after the cursor. If youmake a mistake, press the microphone’s [DWN] key to move back to the first digit, thenre-enter the correct number.7. When entry of all digits is complete, press the [SET] key momentarily to save the newsetting.8. If you wish to store another DTMF string, rotate the “Main” band DIAL knob to selectanother DTMF memory register, then repeat steps 4 through 7 above.9. When all required DTMF memories are filled to your satisfaction, press and hold in the“Main” band DIAL knob for 1/2 second to exit to normal operation.To transmit the memorized telephone number, use the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #15 (DTMF W).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the DTMF Autodialer memory channel to be transmitted.4. Press and hold in the “Main” band DIAL knob for 1/2 second to exit to normal operation.5. Press the PTT switch.6. While still holding the PTT switch in, press the “Main” band [HM] key momentarily totransmit the tone string.Once you have pressed the [HM] key in the above step, you can release the PTT switch, asthe Autodialer will transmit the whole DTMF string automatically.DTMF AUTODIALER OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
49FT-8800R Operating ManualTo speed at which the DTMF digits are sent can be changed. Three speed levels are avail-able: 50 ms (High: 20 digits per second), 75 ms (Mid: 13 digits per second), and 100 ms(Low: 10 digits per second).To select the speed, use the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #14 (DTMF S).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired speed.4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.You can also set a longer delay between the time you press the [SCN] key (with PTT switchpressed) and the first DTMF digit is sent.To set a delay time, use the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #13 (DTMF D).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired time (50/250/450/750/1000 ms).4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.DTMF AUTODIALER OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
50 FT-8800R Operating ManualThe FT-8800R can be used to access the repeater which is configured to provide access tothe Vertex Standard WIRESTM (Wide-Coverage Internet Repeater Enhancement System).1. Press the “left” VOL knob momentarily to activate the WIRES™ access capability. The“INT ON” will appear for 2 seconds at the “Main” band frequency display. The “int”icon will appear in the memory channel field on the “Sub” band while WIRESTM accessis enabled.2. Rotate the “Main” band DIAL knob, while pressing and holding in the “left” VOL knob,to select the access number (ICODE “0” ~ “9,” “A,” “B,” “C,” “D,” “E (Ú),” or “F (#)”)corresponding to the WIRESTM repeater to which you wish to establish an Internet link(ask your repeater owner/operator if you don’t know the access numbers in the network).3. With the WIRES™ capability activated (as in step 1 above), the FT-8800R will gener-ate a brief (0.1 second) DTMF tone according to your selection in step 2. This DTMFtone is sent at the beginning of every transmission to establish or maintain the link to theremote WIRESTM repeater.4. To disable the WIRESTM access capability, press the “left” VOL knob again.You may access other Internet Link Systems that use a DTMF string for access.1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #15 (DTMF W).3. Press the “Main” band DIAL knob momentarily, then load the DTMF tones which youwish to use to establish an Internet link (ask your repeater owner/operator if you don’tknow the access numbers in the network) into the desired DTMF Memory channel.1) Rotate the “Main” band DIAL knob to select the DTMF Autodialer memory channelnumber (“d-1” through “d-16”).2) Press the “Main” band DIAL knob momentarily.3) Rotate the “Main” band DIAL knob to select the DTMF code, then press the “Main”band DIAL knob momentarily to move the digit.4) Repeat step 3) above.5) Press the “Main” band DIAL knob momentarily to save the new setting.4. Rotate the “Main” band DIAL knob to select Menu #17 (INET).5. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto set this Item to “INT.MEM” (to enable the alternative Internet Link, and disable theWIRES™ access option).6. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.7. Press the “left” VOL knob momentarily to activate the Internet Link System. The “INTON” display will appear for 2 seconds in the “Main” band frequency field. The “int”icon will then appear in the memory channel field on the “Sub” band while the InternetLink System access feature is engaged.INTERNET CONNECTION FEATUREFCC ID: K66FT-8800RVertex Standard Co., Ltd.
51FT-8800R Operating Manual8. Rotate the “Main” band DIAL knob, while pressing and holding in the “left” VOL knob,to select the DTMF access number (“IMEM 1” ~ “IMEM16”) corresponding to the Internetlink repeater to which you wish to establish an Internet link.9. With the Internet link feature activated (as in step 7 above), press the “left” VOL knob ormicrophone’s [P2] key to send out the DTMF tones according to your selection in step9 (to establish the link to the Internet link repeater).10.To disable the Internet link feature, press the “left” VOL knob again.To return to WIRESTM, recall Menu #17 (INET) then set it to “INT. COD.”INTERNET CONNECTION FEATUREFCC ID: K66FT-8800RVertex Standard Co., Ltd.
52 FT-8800R Operating ManualTIME-OUT TIMERThe “Time-Out Timer” (TOT) feature is designed to force the transceiver into the “receive”mode after a preset time period of continuous transmission (the default is 6 minutes). Thisfeature prevents your transceiver from transmitting a “dead carrier” for a long period of timein the event that the microphone PTT switch is accidentally locked in the “TX” condition.The Time-Out Timer’s “switch-to-receive” time may be adjusted, in one minute increments,for any period between 1 and 30 minutes.To change the default (6 minute) time setting, use the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #42 (TOT).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the desired interval (between 1 and 30 minutes), or OFF.4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.AUTOMATIC POWER-OFFThe “Automatic Power-Off” (APO) feature will turn the radio completely off after a user-defined period of PTT switch or key/button inactivity. If you do not press any front panelkeys or buttons, rotate the DIAL knobs or use the microphone’s keys and buttons, or trans-mit, and so long as the transceiver is not scanning or engaged in priority monitoring, theradio will shut itself off after the specified time period. This feature is useful in minimizingbattery drain in a mobile installation if you forget to turn the transceiver off when you leaveyour vehicle.To activate the APO feature, use the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #1 (APO).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto set the desired “switch-off” time (between 1 and 12 hours in 0.5 hours increments), orOFF.4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andexit to normal operation.MISCELLANEOUS SETTINGSFCC ID: K66FT-8800RVertex Standard Co., Ltd.
53FT-8800R Operating ManualPROGRAMMING THE KEY ASSIGNMENTSDefault FT-8800R key functions have been assigned to Microphone’s [P1]/[P2]/[P3]/[P4]buttons (MH-48A6J, [ACC]/[P]/[P1]/[P2] buttons: MH-42B6JS) at the factory. These maybe changed by the user, if you wish to utilize another function on one of these keys.To program the function assigned to a key:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select the Menu Item to be configured (“#28 PGP1,” “#29 PG P2,” “#30 PG P3,” or “#31 PG P4”).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the function you wish to assign to the button you selected in the previous step.4. Press the [SET] key to save the new setting, then rotate the “Main” band DIAL knob toselect another programmable button to modify, if desired, and repeat the above steps.5. Press and hold in the “Main” band DIAL knob for 1/2 second to exit to normal operation.MISCELLANEOUS SETTINGSPress and hold the buttonWhen the “Main” band is set to the Memorymode, press and hold in this button for 1/2 sec-ond to set up the Scan Skip List or PreferentialScan List.Opens the Squelch on the “Main” band to al-low un-muted reception.Activates 1750 Hz Tone Burst.——When the “Main” band is set to the Memorymode or Home Channel, press and hold in thisbutton for 1/2 second to switch the memorychannel display between the “Frequency” for-mat and “Alpha-numeric Tag” format.—Allows tuning in 10-MHz step on the “Main”band VFO.Press this button momentarily to selects Re-peater Shift direction on the “Main” band.Activate the Priority Scanning.Switches operating band on the “Main” band.Activate the Smart Search Feature when the“Main” band is set to the VFO mode.Shift to the “Memory Tuning” feature whenthe “Main” band is set to the Memory mode.FunctionSCANSQL.OFFTCALLRPTRPRILOWTONEMHzREVHOMEBANDVFO/MRPress the buttonActivate the Scanner on the “Main” band.Opens the Squelch on the “Main” band toallow un-muted reception.Activates 1750 Hz Tone Burst.Selects Repeater Shift direction on the“Main” band.Activates the Priority feature on the “Main”band.Selects the transmit power output level on the“Main” band.Activates the CTCSS or DCS operation onthe “Main” band.Allows tuning in 1-MHz step on the “Main”band VFO.Reverses the transmit and receive frequenciesduring split-frequency operation.Switches operation to the “Home” channelon the “Main” band.Toggles the “Main” band of operationbetween the “Left” band and “right” band.Switches frequency control between the VFOand Memory modes on the “Main” band.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
54 FT-8800R Operating ManualFM BANDWIDTH & MIC GAIN CONTROLYou can reduce the microphone input level and receiver bandwidth when operating on tightly-clustered frequencies (channel spacing of 12.5 or 15 kHz). This will reduce the transmitterand receiver deviation, thus minimizing interference to other users (and improving recep-tion, as well).To configure for the narrower bandwidth, use the following procedure:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #44 (WID.NAR).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto change the display to “NARROW.”4. Press and hold in the “Main” band DIAL knob for 1/2 second to save the new setting andto normal operation.To restore the normal (higher) microphone input level and normal (15 kHz) receiver band-width, select “WIDE” in step 3 above.MISCELLANEOUS SETTINGSFCC ID: K66FT-8800RVertex Standard Co., Ltd.
55FT-8800R Operating ManualDCS CODE INVERSIONThe DCS system was first introduced in the commercial LMR (Land Mobile Radio) service,where it is now in widespread use. DCS is sometime referred to by its different proprietarynames, such as DPL® (Digital Private Line®, a registered trademark of Motorola, Inc.).DCS uses a codeword consisting of a 23-bit frame, transmitted (subaudible) at a data rate of134.4 bps (bit/sec). Occasionally, signal inversion can result in the complement of a code tobe sent or received. This prevent receiver squelch from opening with DCS enabled, as thedecoded bit sequence would not match that selected for operation. Typical situations thatmight cause inversion to occur are:¦Connection of an external receiver preamplifier.¦Operating through a repeater.¦Connection of an external linear amplifier.Note that code inversion does not mean that any of the above listed equipment is detective!In certain amplifier configurations, the output signal (phase) is inverted from the input.Small signal or power amplifiers having an odd number (1, 3, 5, etc.) of amplification stagesmay result in inversion of a transmitted or received DCS code.While under most circumstances this should not occur (amplifier designs and industry stan-dards take this into account), if you find that your receiver squelch does not open when bothyou and the other station are using a common DCS code, you or the other station (but notboth) can try the following:1. Press the [SET] key momentarily to enter the Set mode.2. Rotate the “Main” band DIAL knob to select Menu #11 (DCS.N/R).3. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL knobto select the following mode.TRX N:Encoder; Normal, Decoder; NormalRX R:Encoder; Normal, Decoder; Reverse (Inverted)TX R:Encoder; Reverse (Inverted), Decoder; NormalTRX R:Encoder; Reverse (Inverted), Decoder; Reverse (Inverted)4. Press and hold in the “Main” band DIAL knob for 1/2 second to exit to normal operation.Remember to restore the default setting to “TRX N” (Encoder; Normal, Decoder; Normal)when done.MISCELLANEOUS SETTINGSFCC ID: K66FT-8800RVertex Standard Co., Ltd.
56 FT-8800R Operating ManualThe FT-8800R can be set up to operate as a full-featured cross-band repeater via a simpleMenu procedure. This feature is useful for emergency portable work in a remote area, andfor cross-band linking.However, remember these points before using the cross-band repeater function:¦Check the amateur radio rules and regulations for your country to ensure that this type ofoperation is permitted.¦Pick your frequency pair carefully, so as not to cause harmful interference to other users.The use of cross-band repeaters has the potential to cause serious disruption of commu-nications circuits, and the creation of harmful interference to coordinated repeaters isinconsiderate and may be illegal! If you are not sure of active repeater frequencies inyour area, a safe rule is to stay off of the repeater sub-bands and use the FM simplexportion of each band. Contact your area’s frequency coordinator for guidance.¦Remember that the transmit duty cycle will be much higher during repeater service, sowe recommend that the transmit power level be set to a Low setting, to ensure cooleroperation.Transceiver CTCSS settings (Encode/Decode) may, of course, be selected for each band,allowing selective calling for your repeater. However, keep in mind that if the channels youuse are so busy as to motivate you toward CTCSS Decoding, you may not have chosen agood frequency pair on which to operate, as the potential for interference to other users ishigh.Here is the procedure for setting up cross-band repeat operation:1. Before enabling cross-band repeater operation, configure both band settings as desired,and set the squelch such that background noise is silenced.2. Press the [SET] key momentarily to enter the Set mode.3. Rotate the “Main” band DIAL knob to select Menu #45 (X-RPT).4. Press the “Main” band DIAL knob momentarily, “XSTART” will appear on the display.5. Press the “Main” band DIAL knob again to activate the cross-band repeater mode.6. To exit the cross-band repeater mode, Press the [SET] key again.CROSS BAND REPEATER OPERATIONFCC ID: K66FT-8800RVertex Standard Co., Ltd.
57FT-8800R Operating Manual1. Turn the radio off.2. Press and hold in the “left” [V/M] key while turning the radio on.3. Rotate the “right” DIAL knob to select the resetting menu:SETMOD RESET:Resets the Set (Menu) mode settings to their factory defaults.HYPER RESET:Clears the Hyper Memory settings to factory defaults.MEMORY RESET:Clears the Regular Memory settings to factory defaults.ALL RESET:Clears all memories and other settings to factory defaults.4. Press the [SET] key momentarily to complete the reset procedure, once you have madeyour selection in step 3.RESET PROCEDUREFCC ID: K66FT-8800RVertex Standard Co., Ltd.
58 FT-8800R Operating ManualYou can transfer all data stored in one FT-8800R to another FT-8800R by utilizing thehandy “Cloning” feature. This requires a user-constructed Cloning cable which connects theDATA jacks on the two transceivers, as shown below.To clone from one transceiver to another, use the following procedure:1. Insert the Cloning Cable into the DATA jack of each transceiver.2. Turn both transceivers off, then press and hold in the “left” [V/M] key on each radiowhile turning the power on again.3. Rotate the “right” DIAL knob on each radio to select (CLONE START), then press the[SET] key. The display will disappear for a moment, then the “CLONE” notation willappear on the display.4. On the “destination” radio, press the “left” [LOW] key. The “CLONE -RX-” indicatorwill appear on the display.5. Now, on the “source” radio, press the “left” [V/M] key. The “CLONE -TX-” indicator willappear on the display, and the cloning data transfer will immediately begin.6. If there is a problem during the cloning process, “CLONE ERROR” will be displayed.Check your cable connections, and try again.7. If cloning was successful, the “CLONE -RX-” and “CLONE -TX-” indicators will disap-pear.8. Turn both transceivers off, then remove the Cloning Cable. Channel and operating datafor both radios are now identical. They both may be turned on now for normal operation.13.8VDCANTEXT SPDATA13.8VDCANTEXT SPDATAPKSGNDCLONINGFCC ID: K66FT-8800RVertex Standard Co., Ltd.
59FT-8800R Operating ManualThe FT-8800R Set (Menu) mode, already described in parts of many previous chapters, iseasy to activate and set. It may be used for configuration of a wide variety of transceiverparameters, some of which have not been detailed previously. Use the following procedureto activate the Set (Menu) mode:1. Press the [SET] key momentarily to enter the Set mode.2. Turn the “Main” band DIAL knob to select the Menu Item to be adjusted.3. Press the “Main” band DIAL knob momentarily to enable adjustment of the selectedMenu item, then rotate the “Main” band DIAL knob to perform the actual adjustment.4. After completing your selection and adjustment, press and hold in the “Main” bandDIAL knob for 1/2 second to exit the Set mode and exit to normal operation.1) The “h” character which is in front of the menu number denotes “Enable toprovide the individual values for each Hyper Memory Channel.”2) The “b” character which is in front of the menu number denotes “Enable to providethe individual values for each Operating Band and Mode (VFO, Memory Channel, andHome Channel).”MENU (“SET”) MODEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
60 FT-8800R Operating ManualMENU (“SET”) MODEFunctionSelects the Automatic Power Off time (time before powergoes off).Activates/deactivates the Automatic Repeater Shift feature.Selects the ARTS beep mode.Enables/disables the VFO Band edge for the current band.Enables/disables the beeperShifting of CPU clock frequency.Enables/disables the CW identifier during ARTS operation.Stores your callsign into the CW identifier. Up to six char-acters may be stored.Setting of the Display brightness level.Setting the DCS code.Selects “Normal” or “inverted” DCS coding.Selects the Sub Band display format.Setting of the DTMF Autodialer Delay Time.Setting of the DTMF Autodialer Sending Speed.Loading of the DTMF Autodialer Memories.Enables/disables the Automatic Writing feature for theHyper Memory.Selects the Internet Connection mode.Selects the Access Number (DTMF digit) for WIRES™ op-eration.Selects the Access Number (DTMF code) for non-WIRES™Internet Link System access.Selects the key functions for the “right” band functionswitches.Enables/disables the Key/Button Lock feature.Enables/disables the PTT Lock feature.Selects the microphone type to be used.Selects the Audio Mute mode.Stores an Alpha-Numeric “Tag” for a memory channel.Sets the transceiver’s circuitry for the Packet baud rate tobe used.Sets the operating band for Packet operation.Programming the microphone’s [P1]/[ACC] button assign-ment.Programming the microphone’s [P2]/[P] button assignment.Programming the microphone’s [P3]/[P1] button assign-ment.Programming the microphone’s [P4]/[P2] button assign-ment. Adjustd the RF SQL threshold level.Sets the Repeater Shift DirectionSelects the Scan-Resume mode.Selects the Memory Scan modeSets the magnitude of the Repeater Shift.Sets the “flag” for the Memory Scan ListSets the Synthesizer steps.Defines the audio path to the external speaker (when used).Sets the CTCSS Tone Frequency.Selects the Tone Encoder and/or Decoder mode.Sets the Time-Out Timer.Enables/disables the VFO Tracking feature.Reducing the MIC Gain (and Deviation).Switches the Cross-Band Repeater feature on and off.Enables/disables the AM mode.Selects the receiving mode.Item #1234567891011121314151617181920212223242526272829303132333435363738394041424344454647Menu ItemAPOARSARTSBANDBEEPCLK.SFTCWIDCWID WDIMMERDCS.CODDCS.N/RDSP.SUBDTMF DDTMF SDTMF WHYPERINETINET CINET MKEY.MODLOCKLOCKTMICMUTENAMEPCKT SPCKT BPG P1PG P2PG P3PG P4RF SQLRPT.MODSCANSCAN MSHIFTSKIP.MSMSTEPSPCONTTONE FTONE MTOTVFO.TRWID.NARX-RPTAMAUT.AMAvailable ValuesOFF/0.5H - 12HON/OFFIN RNG/OUTRNGBND ON/BNDOFFBEP.ON/BEP.OFFSFT.ON/SFT.OFFTX ON/TX OFF—DIM 1/DIM 2/DIM 3/OFF104 standard DCS CodeTRX N/RX R/TX R/TRX RFREQ/CWID/DC-IN/OFF50MS/250MS/450MS/750MS/1000MS50MS/75MS/100MS—MANUAL/AUTOINT.COD/INT.MEMCODE 0 - 9/A/B/C/D/E/Fd-1 - d-16KEY1/KEY2ON/OFFOFF/BAND R/BAND L/BOTHMH-48/MH-42OFF/TX/RX/(TX/RX)—1200BPS/9600BPSMAIN/R-FIX/L-FIXSCAN/SQL.OFF/TCALL/RPTR/PRI/LOW/TONE/MHz/REV/HOME/BAND/(VFO/MR)OFF/S-2/S-5/S-9/S-FULLRPT.OFF/RPT.–/RPT.+TIME/BUSYMEM/MSM0.00 - 99.50 MHzOFF/SKIP/MSM5.0k/10.0k/12.5k/20.0k/25.0k/50.0kEXT/OFF/INT.EXT/INT50 Standard CTCSS TonesOFF/ENC/ENC.DEC/DCS1 - 30 minutes/OFFON/OFFWIDE/NARROW—ON/OFFAUTO/OFFDefaultOFFø1—BND OFFBEP.ONSFT.OFFTX OFF—DIM 1023TRX NFREQ450MS50MS—MANUALINT.CODCODE 1d-1KEY1OFFOFFø2OFF—1200BPSMAINBANDVFO/MRTONELOWOFFRPT.OFFTIMEMEMø1OFFø1EXT100 HzOFF6 minuteOFFø1—OFFAUTOFCC ID: K66FT-8800RVertex Standard Co., Ltd.
61FT-8800R Operating ManualMenu #1 [APO]Function: Selects the Automatic Power Off time (time before power goes off).Available Values: OFF/0.5 H – 12.0 H in 0.5 hour multiples.Default: OFF (Disables the APO feature)Menu #2 [ARS]Function: Activates/deactivates the Automatic Repeater Shift feature.Available Values: ON/OFFDefault: Depends on the band of operation.Menu #3 [ARTS]Function: Selects the ARTS beep mode.Available Values: IN RNG/OUTRNGIN RNG:Activates the ARTS feature; a high tone beep will sound when the transceiverfirst detects that you are within range, and a low beep will sound when the otherstation goes out of range.OUTRNG:Activates the ARTS feature; a high tone beep will sound every time a pollingtransmission is received from the other station, and a low beep will sound oncewhen the other station goes out of range.Menu #4 [BAND]Function: Enables/disables the VFO Band edge for the current band.Available Values: BND ON/BND.OFFDefault: BND ONBND ON:When the VFO frequency reaches the high band edge of the current band, theVFO frequency will jump to the low band edge of the current band (or viceversa).BND.OFF:When the VFO frequency reaches the high edge of the current band, the VFOfrequency will jump to the low band edge of the next band (or vice versa).Menu #5 [BEEP]Function: Enables/disables the beeperAvailable Values: BEP. ON/BEP.OFFDefault: BEP. ONMenu #6 [CLK.SFT]Function: Shifting of CPU clock frequency.Available Values: SFT. ON/SFT.OFFDefault: SFT.OFFThis function is only used to move a spurious response “birdie,” should it fall on a desiredfrequency.MENU (“SET”) MODEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
62 FT-8800R Operating ManualMenu #7 [CWID]Function: Enables/disables the CW identifier during ARTS operation.Available Values: TX ON/TX OFFDefault: TX OFFMenu #8 [CWID W]Function: Stores your callsign into the CW identifier. Up to six characters may be stored.See page 45 for details.Menu #9 [DIMMER]Function: Setting of the Display brightness level.Available Values: DIM 1/DIM 2/DIM 3/OFFDefault: DIM 1Menu #10 [DCS.COD]Function: Setting the DCS code.Available Values: 104 Standard DCS codes.Default: 023Menu #11 [DCS.N/R]Function: Selects “Normal” or “inverted” DCScoding.Available Values: TRX N/RX R/TX R/TRX RDefault: TRX NMenu #12 [DSP.SUB]Function: Selects the Sub Band display format.Available Values: FREQ/CWID/DC-IN/OFFDefault: FREQFREQ:Displays the “Sub” band frequency (Dual band operation).CWID:Displays the CW ID.DC-IN:Displays the DC supply voltage.OFF:No Display.Note: When this Menu Item is set to any selection other than the “FREQ” the “Sub” bandreceiver will be disabled.Menu #13 [DTMF D]Function: Setting of the DTMF Autodialer Delay Time.Available Values: 50MS/250MS/450MS/750MS/1000MSDefault: 450MSMENU (“SET”) MODEDCS CODE023 025 026 031 032 036 043 047 051 053054 065 071 072 073 074 114 115 116 122125 131 132 134 143 145 152 155 156 162165 172 174 205 212 223 225 226 243 244245 246 251 252 255 261 263 265 266 271274 306 311 315 325 331 332 343 346 351356 364 365 371 411 412 413 423 431 432445 446 452 454 455 462 464 465 466 503506 516 523 526 532 546 565 606 612 624627 631 632 654 662 664 703 712 723 731732 734 743 754 – – – – – –FCC ID: K66FT-8800RVertex Standard Co., Ltd.
63FT-8800R Operating ManualMenu #14 [DTMF S]Function: Setting of the DTMF Autodialer Sending Speed.Available Values: 50MS (high speed)/75MS (mid speed)/100MS (low speed) (ms)Default: 50MSMenu #15 [DTMF W]Function: Loading of the DTMF Autodialer Memories. See page 46 for details.Menu #16 [HYPER]Function: Enables/disables the Automatic Writing feature for the Hyper Memory.Available Values: MANUL/AUTODefault: MANUALMANUL:Disables the Automatic Writing feature.AUTO:Enables the Automatic Writing feature. The Hyper memory data changes auto-matically when the radio’s configuration is changed (such as Mode change, BandChange, etc.).Menu #17 [INET]Function: Selects the Internet Connection mode.Available Values: INT.COD/INT.MEMDefault: INT.CODINT.COD:Sets up the Internet Connection mode for WIRESTM access.INT.MEM:Sets up the Internet Connection mode for other (DTMF string) Internet LinkSystem access.Menu #18 [INET C]Function: Selects the Access Number (DTMF digit) for WIRES™ operation.Available Values:CODE 0 ~ CODE 9, CODE A, CODE B, CODE C, CODE D, CODE E(#), CODE F(Ú)Default: CODE 1Menu #19 [INET M]Function: Selects the Access Number (DTMF code) for non-WIRES™ Internet Link Sys-tem access. See page 48 for more details.Available Values: d-1 ~ d-16Default: d-1Menu #20 [KEY.MOD]Function: Selects the key functions for the “right” band function switches.Available Values: KEY1/KEY2Default: KEY1MENU (“SET”) MODEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
64 FT-8800R Operating ManualMenu #21 [LOCK]Function: Enables/disables the Key/Button Lock feature.Available Values: ON/OFFDefault: OFFMenu #22 [LOCKT]Function: Enables/disables the PTT Lock feature.Available Values: OFF/BAND R/BAND L/BOTHDefault: OFFOFF:Enables the PTT switch.BAND R:Disables the PTT switch on the “right” band.BAND L:Disables the PTT switch on the “left” band.BOTH:Disables the PTT switch on the “both” band.Menu #23 [MIC]Function: Selects the microphone type to be used.Available Values: MH-48/MH-42Default: Depends on transceiver version.Menu #24 [MUTE]Function: Selects the Audio Mute mode.Available Values: OFF/TX/RX and TX/RXDefault: OFFOFF:Disables the Audio Mute feature.TX:Reduces the audio level of the “Sub” band whenever you transmit on the “Main”band.RX:Reduces the audio level of the “Sub” band whenever you receive a signal on the“Main” band.TX/RX:Reduces the audio level of the “Sub” band whenever you receive a signal on the“Main” band or you transmit on the “Main” band.Menu #25 [NAME]Function: Stores an Alpha-Numeric “Tag” for a memory channel. See page 33 for details.Menu #26 [PCKT S]Function: Sets the transceiver’s circuitry for the Packet baud rate to be used.Available Values: 1200bps/9600bpsDefault: 1200bpsMENU (“SET”) MODEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
65FT-8800R Operating ManualMENU (“SET”) MODEMenu #27 [PCKT B]Function: Sets the operating band for Packet operation.Available Values: MAIN/R-FIX/L-FIXDefault: MAINMAIN:Packet can be operated on the “Main” band.R-FIX:Packet can be operated on the “right” band only.L-FIX:Packet can be operated on the “left” band only.Menu #28 [PG P1]Function: Programming the microphone’s [P1]/[ACC] button assignment. See page 51 fordetails.Menu #29 [PG P2]Function: Programming the microphone’s [P2]/[P] button assignment. See page 51 fordetails.Menu #30 [PG P3]Function: Programming the microphone’s [P3]/[P1] button assignment. See page 51 fordetails.Menu #31 [PG P4]Function: Programming the microphone’s [P4]/[P2] button assignment. See page 51 fordetails.Menu #32 [RF SQL]Function: Adjustd the RF SQL threshold level.Available Values: OFF/S-2/S-5/S-9/S-FULLDefault: OFFNote: This Menu Item can be set independently on both the “left” and “right” bands.Menu #33 [RPT.MOD]Function: Sets the Repeater Shift DirectionAvailable Values: RPT.OFF/RPT. –/RPT. +Default: RPT.OFF (SIMP)Note: This Menu Item can be set independently on both the “left” and “right” bands.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
66 FT-8800R Operating ManualMENU (“SET”) MODEMenu #34 [SCAN]Function: Selects the Scan-Resume mode.Available Values: TIME/BUSYDefault: BUSYTIME:The scanner will halt on a signal it encounters, and will hold five seconds. If you donot take action to disable the scanner within five seconds, the scanner will resumeeven if the stations are still active.BUSY:The scanner will halt on a signal it encounters. Two seconds after the carrier hasdropped because the other station(s) ceased transmission, the scanner will resume.Note: This Menu Item can be set independently for each band.Menu #35 [SCAN M]Function: Selects the Memory Scan modeAvailable Values: MEM/MSMDefault: MEMMEM:Enables Memory Scanning on all memory channels.MSM:Enables Memory Scanning on “flagged” Memory Channels only.Menu #36 [SHIFT]Function: Sets the magnitude of the Repeater Shift.Available Values: 0.00 - 99.95 MHz (50 kHz step)Default: Depends on the band of operation.Note: This Menu Item can be set independently for each band.Menu #37 [SKP.MSM]Function: Selects what action will happen on a “flagged” Memory ChannelAvailable Values: OFF/SKIP/MSMDefault: MEMOFF:All memory channels will be scanned (the “flag” will be ignored).SKIP:The scanner will “skip” the flagged channels during scanning.MSM:The scanner will “only scan” the flagged channels during scanning.Menu #38 [STEP]Function: Sets the Synthesizer steps.Available Values: 5.0 k/10.0 k/12.5 k/15.0 k/20.0 k/25.0 k/50.0 kDefault: Depends on the band of operation.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
67FT-8800R Operating ManualNote: This Menu Item can be set independently for each band.Menu #39 [SPCONT]Function: Defines the audio path to the external speaker (when used).Available Values: EXT/OFF/ INT.EXT/INTDefault: EXTEXT:The audio is routed to external speaker (internal speaker is off).OFF:The audio is not routed (internal and external speakers are both off).INT.EXT:The audio is routed to both the internal and external speakers.INT:The audio is routed to the internal speaker only (external speaker is off).Menu #40 [TONE F]Function: Sets the CTCSS Tone Frequency.Available Values: 50 Standard CTCSS TonesDefault: 100 HzNote: This Menu Item can be set independently for each band and, independently in eachmemory.Menu #41 [TONE M]Function: Selects the Tone Encoder and/or Decoder mode.Available Values: OFF/ENC/ENC.DEC/DCSDefault: OFFENC: CTCSS EncoderENC.DEC: CTCSS Encoder/DecoderDCS: Digital Code Squelch Encoder/DecoderMenu #42 [TOT]Function: Sets the Time-Out Timer.Available Values: 1 - 30 minutes or OFFDefault: 6 minutesMenu #43 [VFO.TR]Function: Enables/disables the VFO Trackingfeature.Available Values: ON/OFFDefault: OFFMENU (“SET”) MODECTCSS TONE FREQUENCY (Hz)  67.0   69.3   71.9   74.4   77.0   79.7  82.5   85.4   88.5   91.5   94.8   97.4100.0 103.5 107.2 110.9 114.8 118.8123.0 127.3 131.8 136.5 141.3 146.2151.4 156.7 159.8 162.2 165.5 167.9171.3 173.8 177.3 179.9 183.5 186.2189.9 192.8 196.6 199.5 203.5 206.5210.7 218.1 225.7 229.1 233.6 241.8250.3 254.1 ––––FCC ID: K66FT-8800RVertex Standard Co., Ltd.
68 FT-8800R Operating ManualMenu #44 [WID.NAR]Function: Reducing the MIC Gain (and Deviation).Available Values: WIDE/NARROWDefault: Depends on the band of operation.Note: This Menu Item can be set independently for each band.Menu #45 [X-RPT]Function: Switches the Cross-Band Repeater feature on and off.Perform this Menu function to switch the Cross-Band Repeater feature on and off. See page54 for details.Menu #46 [AM]Function: Enables/disables the AM mode.Available Values: ON/OFFDefault: OFFMenu #47 [AUT. AM]Function: Selects the receiving mode.Available Values: AUTO/OFFDefault: AUTO (AM in Aeronautical Band, FM elsewhere)MENU (“SET”) MODEFCC ID: K66FT-8800RVertex Standard Co., Ltd.
1. Changes or modifications to this device not expressly approved by VERTEXSTANDARD could void the user’s authorization to operate this device.2. This device complies with part 15 of the FCC Rules. Operation is subject tothe following two conditions; (1) this device may not cause harmfulinterference, and (2) this device must accept any interference includinginterference that may cause undesired operation.3. The scanning receiver in this equipment is incapable of tuning, or readilybeing altered, by the User to operate within the frequency bands allocatedto the Domestic public Cellular Telecommunications Service in Part 22.WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULARRADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULESAND FEDERAL LAW.DECLARATION BY MANUFACTURERThe Scanner receiver is not a digital scanner and is incapable of being convertedor modified to a digital scanner receiver by any user.Part 15.21:  Changes or modifications to this device not expressly approvedby Vertex Standard could void the user’s authorization to operate this device.FCC ID: K66FT-8800RVertex Standard Co., Ltd.
Printed in JapanCopyright 2003VERTEX STANDARD CO., LTD.All rights reserved.No portion of this manualmay be reproducedwithout the permission ofVERTEX STANDARD CO., LTD. 0304?-0YEH0 1 8 M100FCC ID: K66FT-8800RVertex Standard Co., Ltd.

Navigation menu