Yaesu Musen VX-210U Transmitter held to face User Manual C DOCUME 1 manual 1 VX

Download:
Mirror Download [FCC.gov]
Document ID	168339
Application ID	QTEXJlXBCn08PnScZs2kbw==
Document Description	RF Exposure Manual Statement
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.1kB (88754 bits)
Date Submitted	2001-09-07 00:00:00
Date Available	2001-09-26 00:00:00
Creation Date	2001-09-07 10:50:50
Producing Software	Acrobat PDFWriter 4.05 Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	C:\DOCUME~1\manual\デスク~1\VX-
Document Creator	Adobe PageMaker 6.5J - [C:\DOCUME~1\manual\デスク~1\VX-210A\VTXhonbun_B3英+406MHz_2.P65]
Document Author:	manual

Before You Begin
Battery Pack Installation and Removal
VX-210A
Operating Manual
r To install the battery, hold the transceiver with your left hand, so your palm is
over the speaker and your thumb is on the top of the belt clip. Insert the battery
pack into the battery compartment on the back of the radio while tilting the Belt
Clip outward, then close the Battery Pack Latch until it locks in place with a
“Click.”
Controls & Connectors
LED Indicator
Glows Green
BlinkingGreen
Glows Red
Blinking Red
Blinking Yellow
ACC on
Busy Channel (or SQL off)
Transmitting
Battery Voltage is low
Receiving a Selective Call
Monitor
Talk Around
Press the ACC button to override (disable) the Tone Squelch.
Background noise or incoming signals will now be heard whether or not a matching tone is present on the signal. Press the ACC button once more to resume
normal (quiet) Tone Squelch action.
Squelch OFF
Press the ACC button to override both the Noise and Tone squelch systems.
Again press the ACC button to resume normal (quiet) Noise and Tone squelch
action.
Low Power
CH (Channel) Selector
Antenna
Description of Operating Functions
Press the ACC button to set the radio's transmitter to the “Low Power” mode,
thus extending battery life. Press the ACC button again to return to “High Power”
operation when in difficult terrain.
VOL/PWR Knob
Push To Talk
(PTT) Switch
Scan
MIC/SP Jack
(External Mic/Earphone )
r To remove the battery, turn the radio off and remove any protective cases. Open
the Battery Pack latch on the bottom of the radio, then slide the battery downward and out from the radio while holding the Belt Clip.
Speaker
Do not attempt to open any of the rechargeable Ni-Cd packs, as they could
explode if accidentally short-circuited.
Caution!
ACC Button
Low Battery Indication
Microphone
r As the battery discharges during use, the voltage gradually becomes lower. When
the battery voltage reaches 6.3 volts, substitute a freshly charged battery and
recharge the depleted pack. The TX/BUSY indicator on the top of the radio will
blink red when the battery voltage is low.
r Avoid recharging Ni-Cd batteries often with little use between charges, as this
can degrade the charge capacity. We recommend that you carry an extra, fullycharged pack with you so the operational battery may be used until depletion
(this “deep cycling” technique promotes better long-term battery capacity).
Battery Pack Latch
Notice !
There are no owner-serviceable parts inside the transceiver. All service jobs
must be referred to an authorized
Service Representative. Consult
your Authorized
Dealer for installation of optional accessories.
The Scanning feature is used to monitor multiple channels programmed into the
transceiver. While scanning, the radio will check each channel for the presence
of a signal, and will stop on a channel if a signal is present.
r To activate scanning:
Press the ACC button.
The scanner will search the channels, looking for “active” ones; it will pause
each time it finds a channel on which someone is speaking.
r To stop scanning:
Press the ACC button.
Operation will revert to the channel to which the CH knob is set.
Follow-Me Scan
“Follow-Me” Scan feature checks a User-assigned Priority Channel regularly as
you scan the other channels. Thus, if only Channels 1, 3, and 5 (of the 8 available channels) are designated for “Scanning,” the user may nonetheless assign
Channel as the “User-assigned” Priority Channel via the “Follow-Me” feature.
Press the ACC button to activate “Follow-Me” scanning, then pull and turn the
CH selector knob to the channel which you want to designate as the “UserAssigned Priority Channel”. When the scanner stops on an “active” channel, the
User-assigned Priority Channel will automatically be checked every few seconds.
Dual Watch
This device complies with Part 15 of the FCC rules. Operation is subject to the
condition that this device does not cause harmful interference.
0107Q-AE
Operation
Preliminary Steps
r Install a charged battery pack onto the transceiver, as described previously.
r Screw the supplied antenna onto the Antenna jack. Never attempt to operate this
transceiver without an antenna connected.
r If you have a Speaker/Microphone, we recommend that it not be connected until
you are familiar with the basic operation of the VX-210A.
Operation Quick Start
r Turn the top panel’s VOL/PWR knob clockwise to turn on the radio on.
VOL
15
r Rotate the VOL/PWR knob to set the volume
level. If no signal is present, press and hold in
the ACC button (the lower button on the left
side) for more than 1 second (when “MONITOR” is assigned to the ACC button); background noise will now be heard, and you may
use this to set the VOL/PWR knob for the desired audio level.
r Press and hold in the ACC button (when
“MONITOR” is assigned to the ACC button)
for more than 1 second (or press the ACC button twice) to quiet the noise and resume normal
(quiet) monitoring.
11
CH
13
r Pull and turn the top panel’s CH selector knob
to choose the desired operating channel.
The Dual Watch feature is similar to the Scan feature, except that only two channels are monitored: the current operating channel, and the “Priority” channel.
r To activate Dual Watch:
Press the ACC button.
The scanner will search the two channels; it will pause each time it finds a
channel on which someone is speaking.
r To stop Dual Watch:
Press the ACC button.
Operation will revert to the channel to which the CH knob is set.
r To transmit, press and hold in the PTT switch.
Speak into the microphone area of the front
panel grille (lower left-hand corner) in a normal voice level. To return to the Receive mode,
release the PTT switch.
r If a Speaker/Microphone is available, remove the plastic cap and its two mounting screws from the right side of the transceiver, then insert the plug from the
Speaker/Microphone into the MIC/SP jack; secure the plug using the screws
supplied with the Speaker/Microphone. Hold the speaker grille up next to your
ear while receiving. To transmit, press the PTT switch on the Speaker/Microphone, just as you would on the main transceiver’s body.
Note:Save the original plastic cap and its mounting screws. They should be reinstalled when not using the Speaker/Microphone.
Key Functions
The VX-210A provides a programmable “ACC” (Accessory) button. The ACC
button’s functions can be customized (set to any of a variety of functions), via programming by your VERTEX STANDARD dealer, to meet your communications/
network requirements. The particular function to be activated or disabled may require a simple press of the ACC button, or it may require that the ACC button be
pressed and held in for one second (or more). See the discussion below.
Some features may require the purchase and installation of optional internal accessories.
ACC button
Function
The possible ACC button
Press Press and Hold
programming features are illusNone
trated below, and their funcMonitor
tions are explained in the next
Squelch OFF
chapter. For further details,
Low Power
contact your VERTEX STANScan
DARD dealer.
Follow-me Scan
For future reference, check
the box next to the function that Dual Watch
has been assigned to the ACC Talk Around
button on your particular radio,
Call/Reset
and keep it handy.
Speed Dial
TX Save Off
ACC 1
ACC 2
Press the ACC button to activate the Talk Around feature when you are operating on duplex channel systems (separate receive and transmit frequencies, utilizing a “repeater” station). The Talk Around feature allows you to bypass the repeater station and talk directly to a station that is nearby. This feature has no
effect when you are operating on “Simplex” channels, where the receive and
transmit frequencies are already the same.
Note that your dealer may have made provision for “Talk Around” channels by
programming “repeater” and “Talk Around” frequencies on two adjacent channels. If so, the ACC key may be used for one of the other Pre-Programmed
Functions.
Call/Reset
When the 2-tone selective calling unit is installed, press the ACC button to silence the receiver and reset for another call, when a communication is finished.
Speed Dial
Your Dealer may have pre-programmed Auto-Dial telephone number memories
into your radio.
To dial a number, just press the Dealer-assigned ACC button for Speed Dialing.
The DTMF tones sent during the dialing sequence will be heard in the speaker.
TX Save Off
Press the ACC button to disable the Transmit Battery Saver, if you are operating
in a location where high power is almost always needed.
The Transmit Battery Saver helps extend battery life by reducing transmit power
when a very strong signal from an apparently nearby station is being received.
Under some circumstances, though, your hand-held radio may not be heard well
at the other end of the communication path, and high power may be necessary at
all times.
ACC 1
Activates an optional Unit (module) while the ACC button is held depressed.
When you release the ACC button, the optional Unit will be disabled.
For further details, contact your VERTEX STANDARD dealer.
ACC 2
Toggles the optional Unit “on” or “off” whenever you press the ACC button.
For example, when the optional “FVP-25” voice encryption unit is installed,
press the ACC button momentarily to disable the voice encryption feature temporarily.
Press the ACC button again to re-enable the voice encryption feature.
Accessories & Options
Important Notice!
FCC RF Exposure Compliance Requirements for Occupational Use Only:
This Radio has been tested and complies with the Federal Communications Commission (FCC) RF exposure limits for Occupational Use/Controlled exposure environment. In addition, it complies with the following Standards and Guidelines:
r FCC 96-326, Guidelines for Evaluating the Environmental Effects of Radio-Frequency Radiation.
r FCC OET Bulletin 65 Edition 97-01 (1997) Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
r ANSI/IEEE C95.1-1992, IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
r ANSI/IEEE C95.3-1992, IEEE Recommended Practice for the Measurement of
Potentially Hazardous Electromagnetic Fields - RF and Microwave.
m This radio is NOT approved for use by the general population in an uncontrolled environment. This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to
control its RF exposure conditions.
m When transmitting, hold the radio in a vertical position with its microphone
1 to 2 inches (2.5 to 5 cm) away from your mouth and keep the antenna at
least 1 inch (2.5 cm) away from your head and body.
m The radio must be used with a maximum operating duty cycle not exceeding
50%, in typical Push-to-Talk (PTT) configurations.
DO NOT transmit for more than 50% of total radio use time (50% duty
cycle). Transmitting more than 50% of the time can cause FCC RF exposure
compliance requirements to be exceeded.
The radio is transmitting when the red LED on the top of the radio is illuminated. You can cause the radio to transmit by pressing the PTT button.
m Always use Vertex Standard authorized accessories.
For North American Users Regarding 406 MHz Guard Band
The U.S. Coast Guard and National Oceanographic and Atmospheric Administration
have requested the cooperation of the U.S. Federal Communications Commission in
preserving the integrity of the protected frequency range 406.0 to 406.1 MHz, which
is reserved for use by distress beacons. Do not attempt to program this apparatus,
under any circumstances, for operation in the frequency range 406.0 - 406.1 MHz if
the apparatus is to be used in or near North America.
FNB-V57
FNB-V57IS
FBA-25
NC-76B
NC-76C
VAC-6400
VAC-400B
VAC-400C
VCM-1
MH-45B4B
MH-37A4B
VC-25
FVP-25
VTP-50
CT-42
CT-27
FTT-17
LCC-210
7.2 V 1100 mAh Ni-Cd Battery Pack
7.2 V 1100 mAh Ni-Cd Intrinsically safe Battery
Alkaline Battery Case (6 Í AA)
120 VAC Wall Charger
230-240 VAC Wall Charger
6-Unit Multi Charger
120 VAC Desktop Rapid Charger
230-240 VAC Desktop Rapid Charger
Mobile Mounting Bracket for VAC-400
Speaker/Microphone
Earpiece/Microphone
VOX Headset
Encryption /DTMF Page Unit
VX-Trunk Unit
PC-Programming Cable (CT-28 + CT-29)
Cloning Cable (Set-to-Set Cloning)
16 keypad for VX-Trunk (VTP-50 required)
Leather Case
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
17210 Edwards Rd., Cerritos, CA 90703, U.S.A.
International Division
8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 1
Creator                         : Adobe PageMaker 6.5J - [C:\DOCUME~1\manual\デスク~1\VX-210A\VTXhonbun_B3英+406MHz_2.P65]
Create Date                     : 2001:09:07 10:50:50
Title                           : C:\DOCUME~1\manual\デスク~1\VX-
Author                          : manual
Producer                        : Acrobat PDFWriter 4.05 Windows NT

EXIF Metadata provided by EXIF.tools