Yaesu Musen VXR-9000U Low Power UHF Transceiver User Manual users manual 1

Download:
Mirror Download [FCC.gov]
Document ID	330975
Application ID	mlm32Qa1KlHCik2yueqORQ==
Document Description	users manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.62kB (232761 bits)
Date Submitted	2003-06-09 00:00:00
Date Available	2003-06-06 00:00:00
Creation Date	2003-04-25 10:18:43
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2003-04-25 10:18:43
Document Title	users manual 1

FCC ID: K66VXR-9000U
Operating Manual
Front Panel
(10)
(6)
(5)
(1)
(2)
(3)
(7) (9) (8)
(4)
(1) Power Switch
Operate the switch to turn the repeater On and Off.
(2) Power Indicator (Main)
A green LED lights when the main power source is used.
(3) Power Indicator (Backup)
A red LED lights whrn the backup power source is used.
(4) Microphone Jack
Connect the microphone plug to this jack. This jack is also used for writing and reading
channel frequency or other configurations via COM Port of PC on which the clone editor
(CE60) is running.
(5) Programmable Function Key
Six push keys are programmable function key (PFK) which have orange indicator
inside each of them. Each key can be programmed two functions for long push and short
push.
1/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
(6) Numeric Display
The display is consisted of two digits seven-segment LED, which shows channel number when the
repeater works normally. An error code is displlayed in case the repeater has a trouble with it.
(7) TX Indicator
A red LED lights when the repeater is transmitting.
(8) Busy Indicator
A green LED lights when the receiving channel is busy.
(9) Volume Knob
Volume knob to adjust the output level of front speaker and external speaker jack on the back panel.
(10) Speaker
Internal Speaker.
2/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
Rear Panel
(1)
(2)
(3)
(6)
(5)
(7) (4)
(1) Antenna Connector for Transmission
The 50-ohm coaxial feedline to the antenna for transmission must be connected here, using Type-N
coaxial connector.
(2) DSUB 25-pin Accessory Connector
DB-25 connector allows the repeater to be remote-controlled by external controller. Analog signals,
such as TX_AF_IN, DISC_OUT, RSSI, and so on, are input and output. Furthermore, this repeater
has eight port programmable input/output feature (PIO) for various control (or being controlled).
Each port can be programmed their function, input or output, and its logic (output only).
(3) Antenna Connector for Reception
The 50-ohm coaxial feedline to the antenna for reception must be connected here, using Type-BNC
coaxial connector.
(4) Main Power Source Connector
A power supply for main power source should be connected here.
3/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
(5) Backup Power Source Terminals
A power supply for backup power source, such as rechargeable battery should be connected here.
When the repeater is working by main power source, a trickle charge current is present here.
(6) Circuit Protection Fuse
Two 15A blade fuses for main and backup power source.
(7) External Speaker Jack
3.5 mm 2-pin extenal speaker jack. Recommanded load impedance is from 4 ohm to 16 ohm. The
output level varies in accordance with the position of volume knob on the front panel.
4/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
The VXR-9000 repeater is provided with a 25-pin DB-25F female connector for interconnections to
accessories.Use a DB-25M 25-pin male connector to connect accessories to the repeater. The pins on
the accessory
connector are explained in detail as follows:
Pin 1: GND
Chassis ground for all logic levels and power supply return.
Pin 2: GND
Chassis ground for all logic levels and power supply return.
Pin 3: +13.6 V [Power Supply]
This pin provides 13.6 Volts, 1.0 A, regulated DC
from the repeater supply. Use a 1 A fuse in the external
device’s DC line to prevent damage to the repeater.
Pin 4,6,8,10,12,16,19,25: Programmable I/O_0~7
this repeater has eight port programmable input/output feature (PIO) for various control (or being
controlled). Each port can be programmed their function, input or output, and its logic (output only).
Pin 5: TX AF IN [Analog Transmitter Input]
(Voice Band: 300 ~ 3,000 Hz)
Approximately 0.254 Vrms audio input on this pin
will produce full system deviation at 1 kHz (±5 kHz
deviation with 25 kHz channel spacing, ±2.5 kHz
deviation with 12.5 kHz channel spacing). Input impedance
is 600 .. This audio is injected before the
splatter filter stage, so excess signal input levels are
clipped.
Use shielded cable to connect to this pin, and connect
the shield to GND.
Pin 7: TONE IN [Transmitter Input]
(Sub-audible Band: 6 ~ 250 Hz)
Applying a 0.1 Vrms sub-audible tone produces 10%
of full system deviation. The input impedance is 600
W, and has a flat response characteristic (repeater
deviation is constant for a given signal level over
the frequency range of 6 ~ 250 Hz). Injecting too high
a voltage here causes over-deviation of CTCSS or
DCS, degrading performance. Use shielded cable to
connect to this pin, connecting the shield to GND.
5/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
Pin 9: TX ATT
This output is intended for controlling an external
coaxial switching relay. It is an open collector output
which can sink approx. 10 mA when active. This
signal only switches if the repeater has been programmed
Pin 11: DISC OUT [Analog Output]
(Wide-Band: 0 ~ 3,000 Hz)
Received signals with full system deviation produce
1 Vp-p audio at this pin. The output impedance is
600 ., and is extracted before the de-emphasis and
squelch circuitry. Use shielded cable to connect to
this pin, and connect the shield to GND.
Pin 13: GND
Chassis ground for all logic levels and power supply return.
Pin 14: GND
Chassis ground for all logic levels and power supply return.
Pin 15: RSSI [Analog Output]
A DC voltage proportional to the strength of the signal
currently being received (Receiver Signal
Strength Indicator) is provided on this pin. This low
impedance output is generated by the receiver IF
sub-system and buffered by an internal op-amp.
Typical voltages are graphed as follows:
Pin 17: COAX. SW [Logic Output (Active Low)]
This output is intended for controlling an external
coaxial switching relay. It is an open collector output
which can sink approx. 10 mA when active. This
signal only switches if the repeater has been programmed
for “SIMPLEX” mode. If programmed
for “DUPLEX,” the signal remains open (high impedance)
at all time.
Pin 18: RXD LOW
[Digital Output for DATA Communications]
(300 ~ 3,000 Hz)
This pin is an output for low speed receiving data
signals (typically 1200 bps), with the data being extracted
6/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
after the de-emphasis and low pass filter
stages.
Pin 20: RXD HIGH
[Digital Output for DATA Communications]
(Max.: 5 kHz)
This pin is an output for high speed receiving data
signals (typically 9600 bps), with the data being extracted
immediately after the discriminator prior to
any de-emphasis).
Pin 21: NSQ DET
This is an open-collector, active-low output capable
of sinking about 10 mA. It indicates that the receiver
squelch is open. If the squelch control is properly
set, this indicates a carrier on the receiver channel.
Pin 22: TXD LOW
[Digital Input for DATA Communications]
(300 ~ 3,000 Hz)
This pin is intended to be used as a low speed digital
data signal input to the repeater (typically 1200
bps). This digital data signal is injected before transmitter
pre-emphasis and limiting stage, so excess signal
input levels are clipped.
Pin 23: EXT PTT
This input is internally pulled up to 5 VDC. When
pulled low by an external device, it keys the repeater
transmitter while the repeater is operating in the
BASE mode. Avoid voltage in excess of 5 V on this
pin, or internal damage to the microprocessor on the
repeater CNTL Unit may result.
Pin 24: TXD HIGH
[Digital Input for the DATA Communications]
(0 ~ 5 kHz)
This pin is intended to be used as a high speed digital
data signal input to the repeater (typically 9600
bps). This digital data signal is injected after transmitter
splatter filter stage.
7/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
･ Programmable Function Key
Six push keys are programmable function (PF) key which have orange indicator inside
each of them. Each key can be programmed two functions for long push and short push.
The PF key functions can be customized, via programming by your VERTEX
STANDARD dealer, to meet your communications/network requirements. Some
features may require the purchase and installation of optional internal accessories. The
possible PF key programming features are illustrated below, and these functions are
explained on the pages to follow.
For further details, contact your VERTEX STANDARD dealer. For future reference,
check the box next to the function that has been assigned to each PF key on your
particular radio, and keep it handy.
Function
PF1
1>
1<
PF2
1> 1<
PF3
1> 1<
PF4
1> 1<
PF5
1> 1<
PF6
1> 1<
CH Down
CH Up
Compander
CTCSS/DCS Enc
CTCSS/DCS Dec
CW ID
Two Tone Dec
CW ID Signal
CW Message 1
CW Message 2
CW Message 3
CW Message 4
CW Message 5
CW Message 6
CW Message 7
CW Message 8
DC Power Save
Encryption
Encryption Code
Key Lock
Local PTT
Monitor
Monitor M
Multi Tone
Panel Indicator
Remote
Repeat
Reset
Scan
8/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
Squelch
Test Tone
Test Tone M
TOT
Transmit
TX Power Mid
TX Power Low
CH Down
Press (or Press and hold) the assigned PF key of the “CH Down” to switch the lower
operating channel.
CH Up
Press (or Press and hold) the assigned PF key of the “CH Up” to switch the higher
operating channel.
Compander
Press (or Press and hold) the assigned PF key of the “Compander” to turn the
“Compander” IC “ON” or “OFF.”
The “Compander” IC contains two variable gain circuits configured for compressing and
expanding the dynamic range of the repeater’s transmitted and received audio signal.
When you enable this function, the signal-to-noise ratio can be improved by reducing
the transmitted audio dynamic range.
CTCSS/DCS Enc
Press (or Press and hold) the assigned PF key of the “CTCSS/DCS Enc” to turn the
CTCSS/DCS Encoder “ON” or “OFF.”
CTCSS/DCS Dec
Press (or Press and hold) the assigned PF key of the “CTCSS/DCS Dec” to turn the
CTCSS/DCS Decoder “ON” or “OFF.”
CW ID
Press (or Press and hold) the assigned PF key of the “CW ID” to turn the CW ID “ON” or
“OFF.”
When CW ID is set to “ON,” superimpose your station’s callsign (determined from your
VERTEX STANDARD dealer) via CW every transmitting.
9/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
Two Tone Dec
Press (or Press and hold) the assigned PF key of the “Two Tone Dec” to turn the 2-Tone
Decoder “ON” or “OFF.”
CW ID Single
Press (or Press and hold) the assigned PF key of the “CW ID Single” to send your
station’s callsign (determined from your VERTEX STANDARD dealer) manually.
CW Message 1 - CW Message 8
Press (or Press and hold) the assigned PF key of the “CW Massage 1 - 8” to send the
pre-programmed CW message (determined from your VERTEX STANDARD dealer)
manually.
DC Power Save
Press (or Press and hold) the assigned PF key of the “DC Power Save” to turn the DC
Power Save feature “ON” or “OFF.”
When DC Power Save is set to “ON,” activate the various power save feature
(determined from your VERTEX STANDARD dealer) while the repeater operate from
the battery or other DC source.
Encryption
Press (or Press and hold) the assigned PF key of the “Encryption” to turn off the Voice
Encryption Unit temporarily.
Encryption Code
Press (or Press and hold) the assigned PF key of the “Encryption Code” to select the
Encryption Code (determined from your VERTEX STANDARD dealer).
Key Lock
Press (or Press and hold) the assigned PF key of the “Key Lock” to lock the front panel
keys (except “Key Lock” key); this can be enabled to prevent repeater settings from
being disturbed.
Local PTT
Press (or Press and hold) the assigned PF key of the “Local PTT” to switch the PTT
button which is connected to the front panel Microphone Jack “ON” and “OFF.”
10/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
Monitor
Press (or Press and hold) the assigned PF key of the “Monitor” to cannel the squelch
circuit (CTCSS, DCS, and Noise), to hear the any signal present on the current channel.
Monitor M
Disable the squelch circuit (CTCSS, DCS, and Noise) while pressing the assigned PF
key of the “Monitor M,” hear the any signal present on the current channel temporarily.
Multi Tone
Press (or Press and hold) the assigned PF key of the “Multi Tone” to switch the Tone
Table between “Main” and “Sub.”
Panel Indicator
Press (or Press and hold) the assigned PF key of the “Panel Indicator” to turn the Front
Panel Illumination “ON” and “OFF.”
Remote
Press (or Press and hold) the assigned PF key of the “Remote” to toggle the operating
mode between the “Remote” mode and “Local” mode.
When the “Remote” mode is selected, the repeater operates according to the control
instructions received from the external device (connected to the ACC jack on the rear
panel). While in the “Local” mode, the repeater operates according to the control data
programmed into the repeater.
Repeat
Press (or Press and hold) the assigned PF key of the “Repeat” to toggle the operating
mode between the “Repeater” mode and “Base Transceiver” mode.
For normal operation, set this key to the “Repeat” mode. When the “Base Transceiver”
mode is selected, you can speak into the microphone to use this repeater as a
transceiver.
Reset
Press (or Press and hold) the assigned PF key of the “Reset” to clears all settings to
defaults.
11/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
Scan
Press (or Press and hold) the assigned PF key of the “Scan” to start scanning.
To stop scanning, press (or Press and hold) this key again.
The scanning feature is used to monitor multiple channels programmed into the
repeater.
Squelch
Press (or Press and hold) the assigned PF key of the “Squelch” to cannel CTCSS and
DCS signaling squelch, to hear the signal present without CTCSS/DCS tone on the
current channel.
Test Tone
Press (or Press and hold) the assigned PF key of the “Test Tone” to transmit the Test
Tone Signal (determined from your VERTEX STANDARD dealer).
Press (or Press and hold) this key again to stop the Test Tone Signal sending.
Test Tone M
Transmit the Test Tone Signal (determined from your VERTEX STANDARD dealer)
while press and holding the assigned PF key of the “Test Tone M.”
TOT
Press (or Press and hold) the assigned PF key of the “TOT” to turn the Time-Out Timer
feature “ON” or “OFF.”
When the TOT is set to “ON,” the repeater return to “receive” mode automatically after
a preset time period (determined from your VERTEX STANDARD dealer) of continuous
transmission.
Transmit
Press the assigned PF key of the “Transmit” to transmit the radio, release it to receive.
TX Power Mid
Press (or Press and hold) the assigned PF key of the “TX Power Mid” to set the
transmitter power to “Mid” mode.
Press (or Press and hold) this key again to return to “High Power” operation.
12/13
Vertex Standard Co., Ltd.
FCC ID: K66VXR-9000U
Operating Manual
TX Power Low
Press (or Press and hold) the assigned PF key of the “TX Power Low” to set the
transmitter power to “Low” mode.
Press (or Press and hold) this key again to return to “High Power” operation.
13/13
Vertex Standard Co., Ltd.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2003:04:25 10:18:43+09:00
Modify Date                     : 2003:04:25 10:18:43+09:00
Page Count                      : 13
Creation Date                   : 2003:04:25 01:18:43Z
Mod Date                        : 2003:04:25 01:18:43Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Metadata Date                   : 2003:04:25 01:18:43Z

EXIF Metadata provided by EXIF.tools