Yamaha Dm2000 Version 2 V2 Supplementary Manual V2.2

DM2000 Version 2 V2.2 Supplementary Manual dm2000v2_en_ss_v22

: Yamaha Dm2000-Version-2-V2-2-Supplementary-Manual yamaha-dm2000-version-2-v2-2-supplementary-manual-647349 yamaha pdf

Open the PDF directly: View PDF .
Page Count: 8

DM2000 V2.2 Supplementary Manual

The DM2000 System Software Version 2.20 features the following changes and additions (including the changes made

up to Version 2.11).

Changes and additions in Version 2.20

❏

More Add-On Effects Packages available (pages 176 and 179)

The following Add-On Effects Packages are now available:

•

AE041

Surround Post Package

•

AE051

Vintage Stomp Package

Due to this addition, effect memories #53 through 67 in the Effects library are now designated as preset effects pro-

grams. These preset programs are dedicated to Add-On Effects. The numbers of effects programs that do not have

Add-On Effects installed are grayed out and cannot be used. The following effects programs in the Effects library

have been dedicated to the new Add-On Effects Packages.

Please refer to the following Yamaha website for the latest information on the Add-On Effects Packages:

http://www.yamahaproaudio.com

❏

Additional trigger sources in the GPI OUTPUT section (pages 266 and 305)

The following parameters have been added as the trigger signal source in the GPI OUTPUT section.

xxx ON TALLY:

The trigger signal is active only while the corresponding channel is turned ON.

The following parameters have been added in the OUTPUT list of the “GPI Trigger Source & Target List” on

page

305.

❏

About the DM2000 Editor version

If you use the DM2000 Editor (Studio Manager) to control the DM2000, update the DM2000 Editor to version

2.1.2 or higher (Studio Manager version 2.1 or higher).

If your Studio Manager CD-ROM version is not X5401

B0

, download the latest version from the following Yamaha

website:

http://www.yamahaproaudio.com

No. Preset name Type

62 Room ER ROOM ER

63 Auto Doppler AUTO DOPPLER

64 Field Rotation FLD ROTATION

65 Max100 MAX100

66 Vintage Phaser VNTG PHASER

67 Dual Phaser DUAL PHASER

# Source

398 CH1 ON TALLY

:

493 CH96 ON TALLY

494 BUS1 ON TALLY

:

501 BUS8 ON TALLY

502 AUX1 ON TALLY

:

513 AUX12 ON TALLY

514 MTX1 ON TALLY

:

517 MTX4 ON TALLY

518 ST ON TALLY

EN

DM2000 V2.2_E.fm Page 1 Monday, June 7, 2010 10:31 AM

Changes in V2.11

❏

Y96K card and MY16-mLAN card support (pages 70 and 349)

The Waves Y96K Plug-in DSP card (supported by Version 2.10) and the MY16-mLAN interface card are now sup-

ported. Also, in accordance with the mLAN MIDI specifications, multiple MIDI ports on SLOT 1 have been

changed to a single port. (Now you do not need to select Ports 1-8.)

Please refer to the following website for the latest information on compatible cards, and on the number of cards

that can be installed in combination with other cards.

http://www.yamahaproaudio.com

Changes in V2.10

❏

MIX C-R SOURCES parameter added to

Control Room Monitor (page 159)

A “MIX C-R SOURCES” parameter has been added in the

CONTROL ROOM SETUP page. In V2.0, you could

choose one item from 2TR D1, D2, D3, A1, or A2 as a

monitor source, plus other sources (STEREO, ASSIGN1,

or ASSIGN2). In V2.1, you can turn the MIX C-R

SOURCES parameter off to disable this simultaneous

selection.

❏

MIX MONITOR SOURCES parameter

added to Surround Monitor (page 160)

A “MIX MONITOR SOURCES” parameter has been

added to the SURROUND MONITOR page. In V2.0, you

could choose ASSIGN1 or ASSIGN2 in addition to a BUS

as the monitor source, but in V2.1 you can turn this

parameter off to disable this simultaneous selection.

DM2000 V2.2_E.fm Page 2 Monday, June 7, 2010 10:31 AM

❏

THX presets added to Surround Monitor (page 161-163)

Presets for the THX pm3 monitor system have been added to the bass management settings for surround monitor-

ing. Several supplements have also been added regarding the surround monitor settings, so please replace the cor-

responding pages with the following.

Configuring Surround Monitoring

Surround monitoring, including speaker setup, monitor matrix, Bass Management, and monitor

alignment, is configured on the Surround Monitor Setup page.

1 Use the MONITOR [DISPLAY] button to locate the Surround Monitor Setup

page.

2Use the cursor buttons to select the parameters, and use the Parameter wheel,

INC/DEC buttons, and [ENTER] button to set them.

SPEAKER SETUP:

These parameters are for setting the volume balance of the surround monitor

speakers. Select the OSC (Oscillator) parameter and choose from PINK NOISE, 500-2K (pink noise

through a 500 Hz to 2 kHz BPF), 1K (1 kHz sinewave), or 50 Hz (50 Hz sinewave). Use the ON/OFF

button to turn the Oscillator on and off. When on, the Oscillator outputs a signal at –20 dB to the

Surround Channels whose icons are highlighted. You can turn on and off Oscillator output for

speakers individually. Speaker icons can be selected by using the cursor buttons. The signal phase of

the LFE Channel can be reversed by using the SW phase button. When ROTATE is on, the Oscillator

signal is output by each speaker in turn in a clockwise direction (3 second signal, 2 second pause).

SURR. MODE:

This indicates the currently selected Surround mode, which is set on the Surround

Mode page (

see page 97

).

MONITOR MATRIX:

This is used to select the Surround Monitor Matrix. In 6.1 Surround mode,

you can select 6.1, 5.1, 3-1, or ST. In 5.1 Surround mode, you can select 5.1, 3-1, or ST. In 3-1 Sur-

round mode, you can select 3-1 or ST.

When a down mix Monitor Matrix is selected, you can attenuate signals by using the ATT parameters.

You can use the Surround Monitor settings in Stereo mode, but Monitor Matrix is fixed to ST.

Note:

If you had been monitoring with the surround mode set to 6.1 and the monitor matrix mode

set to 6.1 on DM2000 units with system software earlier than V2.1, the playback may not always be

correct on V2.1.

Note:

If you choose monitor matrix mode = 3-1, you must set the following three attenuation amounts

to the same value.

• ATT1 for surround mode 3-1

• ATT4 for surround mode 5.1

• ATT5 for surround mode 6.1

These ATT values are not attenuators for down-mixing; rather, they are used as monitor adjustment

attenuators for lowering the playback volume of the Ls, Rs, Ls2, and Rs2 speakers.

DM2000 V2.2_E.fm Page 3 Monday, June 7, 2010 10:31 AM

The following screen shows an example in 6.1 Surround mode and 3-1 Monitor Matrix mode.

•BASS MANAGEMENT

You can set the filter and attenuator settings for each Surround Monitor Channel using eight preset

Bass Management modes. The following presets are available:

ATT1: Adjusts the level difference between LR and LsRs.

ATT2: Adjusts the level difference between C and Bs.

AMP: Corrects the LFE channel level.

HPF1–3: Cut the low range so that the speakers’ supporting frequency ranges will not interfere with the sub-

woofer signals.

HPF1–2: Cut the high range so that the subwoofer’s supporting frequency ranges will not interfere with other

speakers’ signals.

You can set the Bass Management parameters in the following ranges:

The HPF 1, 2, 3, and LPF 1 & 2 values indicate a cut-off frequency and a filter response. For example, “80-12”

means a cutoff frequency of 80 Hz and a filter response of –12 dB/octave.

“L” means Linkwitz filter. Other filters are Butterworth.

Presets Parameters

No. Title HPF 1, 2, 3 LPF1 LPF2 ATT 1 & 2 AMP

1

DVD LFE80Hz 80–12 80–24 80–24 0 10

2

DVD LFE120Hz 80–12 120–42 80–24 0 10

3

Movie LFE80Hz 80–12 80–24 80–24 –3 10

4

Movie LFE120Hz 80–12 120–42 80–24 –3 10

5

Bypass THRU THRU MUTE 0 0

THXD

THX DVD 80-12 120-42 80-24L 0 10

THXF

THX Movie 80-12 120-42 80-24L –3 10

THXM

THX Music 80-12 120-42 80-24L 0 10

Note:

•If you select preset THXD or THXF, you cannot change the parameters.

•If you select preset THXM, you can switch AMP between 10 dB and 0 dB. However, you cannot

change other parameters.

Parameters Range

HPF 1, 2, 3

THRU, 80-12, 80-12L, 80-24, 80-24L

LPF1

THRU, 80-24, 80-24L, 120-42

LPF2

THRU, 80-24, 80-24L, MUTE

ATT 1 & 2

0 to –12 dB (1 dB steps)

AMP

0 to +12 dB (1 dB steps)

DM2000 V2.2_E.fm Page 4 Monday, June 7, 2010 10:31 AM

About the Presets

(1)

DVD LFE80Hz

This is a preset optimized for DVD-Video production. The LFE playback bandwidth is set up to 80

Hz. When using this preset, we recommend that you use an external device to apply an LPF (fc=80

Hz, –24 dB/oct) to the LFE master source.

To monitor audio on DVD-Audio or SACD discs, change the LFE level (AMP) and LPF (LPF1) to

0 dB and THRU, respectively, if necessary.

The LFE output gain on some DVD players and decoders may already be set to +10 dB. To monitor

the output from such devices, change the LFE level (AMP) to 0 dB.

(2)

DVD LFE120Hz

This is also a preset optimized for DVD-Video production. This preset is the same as preset (1) men-

tioned above, except that the LFE playback bandwidth is set up to 120 Hz. Use this preset to monitor stan-

dard LFE signals recorded on DVD-Video discs that include the high-end frequency ranges (120 Hz).

(3)

Movie LFE80Hz

This preset is the same as preset (1) mentioned above, except that the output level of surround chan-

nels is set to –3 dB when the Monitor Matrix mode is 5.1 or 6.1. This preset is suitable for movie

production.

When using this preset, we recommend that you use an external device to apply an LPF (fc=80 Hz,

–24 dB/oct) to the LFE master source.

(4)

Movie LFE120Hz

This preset is the same as preset (2) mentioned above, except that the output level of surround chan-

nels is set to –3 dB when the Monitor Matrix mode is 5.1 or 6.1. This preset is suitable for movie

production.

(5)

Bypass

Use this preset not only for bass management but to bypass all parameters, such as the LFE level &

LPF, surround channel level, etc.

To disable only the bass management, select another preset, then turn off the BASS MANAGE-

MENT ON/OFF button.

■

THX Presets:

The following presets have been approved by THX™ Ltd. for use in THX pm3™ Certified Studios*.

They are designed to provide dedicated parameters for the proper playback of multi-channel audio

content in bass managed systems and to be compatible with subwoofer-satellite type consumer systems.

*Use of a THX preset does not permit a studio to use the designation - THX pm3 Certified Studio.

The THX pm3 Studio Certification Program uses performance and design specifications to create cal-

ibrated environments for optimum sound and picture presentation. For more information, visit the

THX website at http://www.thx.com

[THXD]

THX DVD

This preset is configured for DVD-Video production. Use this preset when mixing and/or monitor-

ing audio content not from a theatrical film source. The parameters cannot be changed.

[THXF]

THX Film

This preset is configured for Film pre-production. Use this preset when mixing and/or monitoring

theatrical film-based content (such as a pre-mix for film). The parameters cannot be changed.

[THXM]

THX Music

This preset is configured for DVD-Music production. Use this preset when mixing and/or monitor-

ing multi-channel music content (including DVD-Audio and SACD). Only one parameter can be

changed. The LFE gain (AMP) can be set to +10dB (default) or 0dB. Select the level that complies

with the standards of the target media. Please note: The LFE output gain on some DVD players,

receivers, and/or decoders may already be set to +10dB. Select the 0dB setting only if the destination

environment (home theatre, etc.) has the LFE gain set to 0dB. Otherwise, use the default setting.

DM2000 V2.2_E.fm Page 5 Monday, June 7, 2010 10:31 AM

•MONITOR ALIGNMENT ATT & DLY ON/OFF

These buttons are used to turn on and off the Monitor Align-

ment Attenuator and Delay parameters of all Surround speak-

ers. The MONITOR ALIGNMENT diagram and Surround

Channel Attenuator and Delay parameters, which are dis-

played when either of these buttons are selected, allow you to

align the surround monitor speakers by attenuating and

delaying Surround Channels as necessary. The Attenuator

parameters can be set –

∞

, –12 dB to +12 dB in 0.1 dB steps. The Delay parameters can be set from

0 to 30 msec in 0.02 msec steps.

❏

Canceling the parameter display value in

the channel strip display (page 274)

A “Ch Numeric Disp OFF” preference has been added to

the PREFERENCES 1 page. In V2.0, the channel strip dis-

play would switch to showing the parameter value when

you operated a channel fader or encoder (pan setting). If

you turn on this preference item, the display will not be

switched to the parameter value.

❏

MY16-C card support (pages 70 and 349)

The MY16-C CobraNet interface card is now supported. However, the following restrictions apply when installing

the card into a DM2000 slot.

•Only one MY16-C card can be used simultaneously, and it can be installed only in one of SLOT 1–3.

•Audio signal transmission and reception are supported, but control signals are not supported.

Please refer to the following website for the latest information on compatible cards, and on the number of cards

that can be installed in combination with other cards.

http://www.yamahaproaudio.com

Note:

•Please note that the above settings apply only to the signals being monitored. They do not affect the

normal bus outputs.

•If you’re monitoring in surround mode 6.1 and monitor matrix mode 6.1, you’ll need to make the

above settings separately from when in other modes.

Tip:

The settings you make here can be stored in the surround monitor library.

DM2000 V2.2_E.fm Page 6 Monday, June 7, 2010 10:31 AM

Memo

DM2000 V2.2_E.fm Page 7 Monday, June 7, 2010 10:31 AM

U.R.G., Pro Audio Division

© 2005 Yamaha Corporation

WW09730

DM2000 V2.2_E.fm Page 8 Monday, June 7, 2010 10:31 AM