Yamaha Dme N Remote Control Protocol Specifications DME Series Remote Control Protocol V3.1(2nd Edition) dme_remote_ctrl_prtcl3102_en DME-N Remote Control Protocol Specifications V3.1(2nd Edition) dme_remote_ctrl_prtcl3102_en 2015-03-09
: Yamaha Dme-N-Remote-Control-Protocol-Specifications yamaha-dme-n-remote-control-protocol-specifications-647431 yamaha pdf
Open the PDF directly: View PDF .Page Count: 23
DME Remote Control Protocol
Specifications
Ver. 3.1
2nd edition
* This protocol document relates to the DME64N, DME24N, and DME Satellite
with DME firmware V1.2 or later.
1. Setup
1.1 Connection
To control one DME
Remote Controller
DME
RS-232C or RS-422
To control multiple DMEs
Multiple DMEs can be controlled individually by connecting them as shown below.
DME 1 (Master)
RS-232C or RS-422
Remote Controller
DME 2 (Slave)
To debug the Remote Controller with a serial control application on a PC such as Hyper Terminal
DME
RS-232C
Connect the Remote controller/PC to the REMOTE connector on the rear panel of the DME using a RS-232C or a RS-422
crossing cable (D-sub; 9 pin female-to-female).
To use the NETWORK connector for Remote Control with the DME communication protocol
(Not supporting DME64N/24N V3.5 or earlier)
Remote Controller
Remote Controller
Ethernet
Network
Switch
Ethernet
Ethernet
REMOTE connector pin assignment
RS-232C
Pin Name
1 Not in use
2 RxD
3 TxD
4 DTR
5 GND
Iｎ/Out Pin
Name
6 DSR
－
Iｎ
7 RTS
Out
8 CTS
Out
9 Not in use
－
Iｎ/Out
Iｎ
Out
Iｎ
-
The pin 4 and 6 are internally shorted.
The pin 7 and 8 are internally shorted.
RS-422
Pin Name
1 Not in use
2 Rx3 Tx4 Tx+
5 GND
Iｎ/Out Pin Name
6 Rx+
－
Iｎ
7 RTS
Out
8 CTS
Out
9 Not in use
－
Iｎ/Out
Iｎ
Out
Iｎ
-
The pin 7 and 8 are internally shorted.
Available crossover cable wirings
2
3
4
5
6
7
8
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
(interlink cross)
DME Remote Control Protocol Specifications V3.1
2
1.2 Remote Controller Setting
The DME series can be controlled from an external device via the REMOTE connector or Ethernet (NETWORK connector; not
supporting DME64N/24N V3.5 or earlier).
The Remote Controller settings for each connection are indicated as below.
Settings for control via the REMOTE connector
Baud Rate
: 38400 bps
Data
: 8bit
Parity
: none
Stop Bit
: 1bit
Flow Control
: none
Settings for control via Ethernet (the NETWORK connector; not supporting DME64N/24N V3.5 or earlier)
IP Address:
Specify the IP address of the DME Satellite to be controlled.
IP Poｒｔ No.: Specify the IP Port No. that is set to the DME Satellite to be controlled.
1.3 DME Setting
The DME series can be controlled from an external device via the REMOTE connector or Ethernet (NETWORK connector; not
supporting DME64N/24N V3.5 or earlier).
The DME series settings for connection via the both connector are indicated as below.
1.3.1. DME series V3.8 or later
To display the setup window
From DME Designer
After going online between DME Designer and the DME series, open the [Hardware] menu -> [Utility] -> [Remote]
page of DME Designer, then set the DME Remote Control parameter.
From the DME panel display (only for DME64N/24N)
Hold down the [Utility] button for three seconds to show the Utility display, then press the [Utility] button
repeatedly until the Remote page is shown. On the page, set the Rmt Ctrl parameter.
To set the parameter values
For control via the REMOTE connector
Select "Remote (RS-232C)" to control the DME via the RS-232C connection.
Select "Remote (RS-422)" to control the DME via the RS-422 connection.
For only the DME Satellite, set the DIP switch (leftmost) on the rear panel to "RS-232C" (up) or "RS-422" (down)
while the power is off as well. If the setting is changed, the DME Satellite needs to be restarted.
For control via Ethernet (the NETWORK connector)
Select "Network".
Generally the IP Port No. does not have to be set. However, it needs to be changed when the network consists of
another network device than the DME series and the network device has the same IP Port No. as the DME
series. Changing the port automatically resets the network connection on the DME, which means that DME
Designer needs to be restarted.
1.3.2. DME64N/24N V3.5 or earlier (not supporting the control via Ethernet)
To display the setup window
From DME Designer
After going online between DME Designer and the DME series, open the [Hardware] menu -> [Utility] -> [Misc]
page of DME Designer, then set the Remote parameter.
From the DME panel display
Hold down the [Utility] button for three seconds to show the Utility display, then press the [Utility] button
repeatedly until the Misc page is shown. On the page, select the Remote parameter.
To set the parameter values
Select "Remote Ctrl (232C)" to control the DME via the RS-232C connection.
Select "Remote Ctrl (422)" to control the DME via the RS-422 connection.
1.3.3. DME Satellite V3.5 or earlier
To display the setup window
After going online between DME Designer and the DME series, open the [Hardware] menu -> [Utility] -> [Misc]
page of DME Designer.
To set the parameter values
For control via the REMOTE connector
Select "Remote Ctrl (232C)" as the Remote parameter to control the DME via the RS-232C connection.
Select "Remote Ctrl (422)" as the Remote parameter to control the DME via the RS-422 connection.
Set the DIP switch (leftmost) on the rear panel to "RS-232C" (up) or "RS-422" (down) while the power is off as
well. If the setting is changed, the DME needs to be restarted.
For control via Ethernet (the NETWORK connector)
Check the checkbox for [Remote Control via Ethernet].
Generally the IP Port No. does not have to be set. However, it needs to be changed when the network consists of
another network device than the DME series and the network device has the same IP Port No. as the DME
series. Changing the port automatically resets the network connection on the DME, which means that DME
Designer needs to be restarted.
DME Remote Control Protocol Specifications V3.1
3
1.4 DME Designer Settings
A parameter or level meter should be registered in each index of the "Remote Control Setup List" dialog on the DME Designer
to control the parameter or obtain the level meter. DME will identify a parameter or level meter to be controlled by including
*
the index in a command.
* What is an index?
An index is the row number in the Remote Control Setup List dialog. You will see each index number at the left column of the list.
1.4.1 DME Parameter Control
Register a DME parameter to be controlled.
An example:
To control ON/OFF of a Fader component and a Source Selector component:
Remote Control Setup List dialog
Function: "Parameter Value Edit" is chosen.
Parameter: A parameter to be controlled is chosen.
To control a fader parameter, choose either "Curve Table method" or "dB method" for a parameter value in the Type column.
Curve Table Method
A method to assign a fader value from 0 to 1023. When Remote Controller transmits a value from 0 to 1023,
DME will set the value (dB) converted by the internal fader curve table to a fader. Adopting this method will
enable the user to control a fader easily without considering a fader dB curve.
dB Method
A method to assign a fader in dB units.
An example:
To control a Fader component level in accordance with a curve table and dB method:
Remote Control Setup List dialog
Function: "Parameter Value Edit" is chosen.
Parameter: A parameter to be controlled is chosen.
Type: An assigning method for a fader parameter is chosen.
1.4.2 Obtaining DME Level Meter
Register a component for which the user would like to obtain a level meter value.
An example:
To obtain a level meter for a fader component and a Cascade Output component:
Remote Control Setup List dialog
Function: Level Meter is chosen.
Parameter: A component for which the user would like to obtain a level meter is chosen.
DME Remote Control Protocol Specifications V3.1
4
2. Command List
Commands Notified to Remote Controller from the DME
No.
1
2
3
4
5
6
7
Category
Parameter Control
Scene Control
Level Meter
Mute Control
Command
PRM
VOL
SCN
CSN
SNM
MTR
MUTE
Definition
To notify a parameter change
To notify a parameter change
To notify scene recall
To notify a scene recall number
To notify a scene name
To notify a meter position
To notify mute set/cancel
Commands for Controlling the DME
No.
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Category
Parameter Control
Scene Control
Level Meter
Mute Control
GPI Control
WAV FILE PLAYER Control
Command
SPR
SVL
RSPR
RSVL
GPR
GVL
RSC
RRSC
GCS
GSN
GMT
GCMT
QCMT
SMC
SMUT
GMUT (*1)
SGO
PWF
SWF (*1)
Definition
To set a parameter
To set a parameter (curve table method)
To relatively set a parameter
To relatively set a parameter (curve table method)
To obtain a parameter
To obtain a parameter (curve table method)
To recall a scene (assigning a scene number)
To recall a scene (assigning a relative value)
To obtain a current scene number
To obtain a scene name
To obtain a level meter position
To set cyclical obtaining of a level meter position
To stop cyclical obtaining of a level meter position
To set the cyclical period for obtaining a level meter position
To set/cancel mute
To obtain mute condition
To control GPI OUT
To play back a file
To stop playback of a file
Utility Commands
Category
No.
27 For debug
Command
ECHO
To set/cancel echo back
Definition
*1 Available only for DME firmware V3.11 or later
DME Remote Control Protocol Specifications V3.1
5
3. Command Specifications
3.1 Basic Command Specifications
A command type transmitted between the DME and the Remote Controller is in the following format:
…
- LF (0 x 0A) will be needed at the end of a command as a line feed code.
- At least one space will be needed between a command name and an option or between options.
- A command must consist of only ASCII character strings. Other character strings cannot be used.
- Optional character strings for parameter values are shown in the following table.
Values
Character strings
-Inf
-13801
-18dB
-1800
-6.5dB
-650
0dB
0
10dB
1000
2kHz
2000
400Hz
400
Pan L 63
-63
0
Pan Center
Pan R 63
+63
ON
1
OFF
0
REVERSE
1
NORMAL
0
Character strings such as "ON" or "HARD" are not returned as a parameter value.
- A fader parameter value will take the following character strings using a curve table method.
(See chapter 1.4.1 for details on curve table methods and the Appendix at the end for values in dB and the character strings.)
A table for a fader of which maximum is 0 dB
Values
-Inf
-60dB
-40dB
-30dB
-20dB
-10dB
0dB
A table for a fader of which maximum is 10 dB
Values
Character strings
0
173
323
423
623
823
1023
-Inf
-60dB
-40dB
-30dB
-20dB
-10dB
0dB
10dB
Character strings
0
123
223
323
423
623
823
1023
3.2 Command Notified to Remote Controller from the DME
3.2.1 Parameter Control Command
1) PRM: Used to change a parameter other than a fader parameter, and a fader using a dB method.
2) VOL: Used to change a fader using a curve table method.
Command Option
PRM
0 [index] [parameter value]
VOL
0 [index] [level value]
The command names stand for "Parameter" and "Volume" respectively.
These commands will be sent from the DME when a parameter registered in Remote Control Setup List of DME Designer is changed
- The first option will always take "0." It can be ignored for the controller; it is reserved for future extensions to the command.
- [index], [parameter value] and [level value] should have appropriate character strings.
- A space will be needed between the command and the option, and between the options.
E.g.) A character string sent from the DME when a parameter for an index of 3 (using a dB method) is changed to -20dB.
PRM 0 3 -2000
A character string sent from the DME when a parameter for an index of 4 (using a curve table method, 10dB at
the maximum) is changed to -20dB.
VOL 0 4 423
DME Remote Control Protocol Specifications V3.1
6
3.2.2 Scene Control Command
3) SCN: Used when a scene is recalled.
Command Option
SCN
0 [scene number]
The command name stands for "Scene."
The DME will send the command when a scene is recalled.
- The first option will always take "0." It can be ignored for the controller; it is reserved for future extensions to the command.
- [scene number] will have an appropriate character string.
- A space will be needed between the command and the option, and between the options.
E.g.) A character string sent to the controller from the DME when Scene 8 is recalled.
SCN 0 8
3.2.3 Mute Control Command
7) MUTE: Used when mute condition is changed
Command Option
MUTE
0 [ON/OFF]
The DME will send the command when Mute ON/OFF is switched.
- The first option will always take "0." It can be ignored for the controller; it is reserved for future extensions to the command.
- The second option will have a character string, either "ON" or "OFF".
- A space will be needed between the command and the option, and between the options.
E.g.) A character string sent to the controller from the DME when Mute is switched off.
MUTE 0 OFF
3.3 Command for the DME Control
3.3.1 Parameter Control Command
8) SPR: Used to set a parameter other than a fader parameter, and a fader using a dB method.
9) SVL: Used to set a fader using a curve table method.
Command Option
SPR
0 [index] [parameter value]
The DME's ACKs when it succeeds
SPR OK
PRM 0 [index] [parameter value]
SVL
0 [index] [curve value]
SVL OK
VOL 0 [index] [level value]
The command names stand for "Set Parameter" and "Set Volume" respectively.
The DME's ACKs when it fails
SPR ERR
SVL ERR
- The first option will always take "0." It is reserved for future extensions to the command.
- [index], [parameter value] and [curve value] should have an appropriate number by a character string.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To change a parameter of an index of 5 to -30dB using a dB method.
SPR 0 5 -3000
To change a parameter of an index of 6 to -30dB using a curve table method (10dB at the maximum).
SVL 0 6 323
- The DME will return two lines of character strings if it succeeds.
The first line should be a character string, either "SPR OK" or "SVL OK".
For details on the character strings "PRM" and "VOL" in the second line, see chapter 3.2.1.
The first line can be ignored; check the second line to find the value after a parameter is changed for a controller.
- The DME will return a character string of either "SPR ERR" or "SVL ERR" if it fails.
E.g.) ACK when it succeeds in changing a parameter of an index of of 5 to -30dB using a dB method.
SPR OK
PRM 0 5 -3000
ACK when it fails in changing a parameter of an index of of 5 to -30dB using a dB method.
SPR ERR
DME Remote Control Protocol Specifications V3.1
7
ACK when it succeeds in changing a parameter of an index of of 6 to -30dB using a curve table method (10 dB at
the maximum).
SVL OK
VOL 0 6 323
ACK when it fails in changing a parameter of an index of of 6 to -30dB using a curve table method (10 dB at the
maximum).
SVL ERR
10) RSPR: Used to relatively set a parameter other than that for a fader, and a fader using a dB method.
11) RSVL: Used to relatively set a fader using a curve table method.
Command Option
RSPR
0 [index] [relative parameter value]
The DME's ACKs when it succeeds
The DME's ACKs when it fails
RSPR OK
RSPR ERR
PRM 0 [index] [parameter value]
RSVL
0 [index] [relative curve value]
RSVL OK
RSVL ERR
VOL 0 [index] [level value]
The command names stand for "Relatively Set Parameter" and "Relatively Set Volume" respectively.
- The first option will always take "0." It is reserved for future extensions to the command.
- [index] should have an appropriate number by a character string.
- An appropriate relative value should be given by a character string to [relative parameter value] and [relative level value].
- One or more spaces are needed between the command and the option, and between the options.
E.g.) When changing a parameter of an index of 5 to +30dB using a dB method.
RSPR 0 5 3000
When changing a parameter of an index of 5 to -30dB using a dB method.
RSPR 0 5 -3000
When increasing a parameter of an index of 6 by 10 steps using a curve table method.
RSVL 0 6 10
When decreasing a parameter of an index of 6 by 10 steps using a curve table method.
RSVL 0 6 -10
- The DME will return two lines of character strings if it succeeds.
The first line will be a character string; "RSPR OK" or "RSVL OK".
For details on the character strings "PRM" and "VOL" in the second line, see chapter 3.2.1.
Ignore the first line but see only the second line to find a value after a parameter is changed for a controller.
A value returned in the second line is the changed value (absolute quantity). Even a relative setting will not return the
quantity changed.
- If it fails, the DME will return one line of a character string, either "RSPR ERR" or "RSVL ERR."
E.g.) ACK when it succeeds in changing a parameter of an index of 5, which is originally -20dB, to -30dB using a dB method.
RSPR OK
PRM 0 5 -5000
ACK when it fails in changing a parameter of an index of 5, which is originally -20dB, to -30dB using a dB method.
RSPR ERR
ACK when it succeeds in decreasing a parameter of an index of 6, which is originally at -20dB, by 10 steps in a
curve table method (10dB at the maximum).
RSVL OK
VOL 0 6 413
ACK when it fails in decreasing a parameter of an index of 6, which is originally at -20dB, by 10 steps using a
curve table method (10dB at the maximum).
RSVL ERR
12) GPR: Used to obtain a parameter using a dB method.
13) GVL: Used to obtain a parameter using a curve table method.
The DME's ACKs when it succeeds
The DME's ACKs when it fails
GPR OK
GPR ERR
PRM 0 [index] [parameter value]
GVL
0 [index]
GVL OK
GVL ERR
VOL 0 [index] [level value]
The command names stand for "Get Parameter" and "Get Volume" respectively.
GPR
Option
0 [index]
DME Remote Control Protocol Specifications V3.1
8
- The first option will always take "0." It is reserved for future extensions to the command.
- [index] will have an appropriate number converted to a character string.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To obtain a parameter of an index of 5 using a dB method.
GPR 0 5
To obtain a parameter of an index of 6 using a curve table method.
GVL 0 6
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string: "GPR OK" or "GVL OK".
For details on the character strings "PRM" and "VOL" in the second line, see chapter 3.2.1.
The first line can be ignored; check the second line to find the parameter value for a controller.
- The DME will return a one-line character string of either "GPR ERR" or "GVL ERR" if it fails.
E.g.) ACK when a parameter of an index of 5 is obtained using a dB method and -30dB is returned.
GPR OK
PRM 0 5 -3000
ACK when it fails in obtaining a parameter of an index of 5 using a dB method
GPR ERR
ACK when a parameter of an index of 6 is obtained using a curve table method (10dB at the maximum) and 30dB is returned.
GVL OK
VOL 0 6 323
ACK when it fails in obtaining a parameter of an index of 6 using a curve table method (10dB at the maximum).
GVL ERR
3.3.2 Scene Control Command
14) RSC: Used to recall a scene.
The DME's ACKs when it succeeds
RSC OK
SCN 0 [scene number]
The command name stands for "Recall Scene".
RSC
Option
0 [scene number]
The DME's ACKs when it fails
RSC ERR
- The first option will always take "0." It is reserved for future extensions to the command.
- [scene number] will have an appropriate number converted to a character string.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To recall Scene 4:
RSC 0 4
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string, "RSC OK".
For details on the character string "SCN" in the second line, see chapter 3.2.1.
The first line can be ignored; check the second line to find if a scene is recalled for a controller.
- The DME will return a one-line character string of "RSC ERR" if it fails.
(The DME will return ERR if the Remote Controller sends the RSC command for an unsaved scene.)
E.g.) ACK when it succeeds in recalling Scene 4:
RSC OK
SCN 0 4
ACK when it fails in recalling Scene 4:
RSC ERR
DME Remote Control Protocol Specifications V3.1
9
15) RRSC: Used to relatively recall a scene.
Option
The DME's ACKs when it succeeds
0 [relative scene number] RRSC OK
SCN 0 [scene number]
The command name stands for "Relatively Recall Scene".
RRSC
The DME's ACKs when it fails
RRSC ERR
This command will perform relative scene recall. For example, it will enable the user to recall "the next scene" and "the
second to last scene".
- The first option will always take "0." It is reserved for future extensions to the command.
- An appropriate number should be given by a character string to [relative scene number]. A plus sign can be omitted but not a minus.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To recall the next scene:
RRSC 0 1
To recall the second to last scene (two scenes prior to current one):
RRSC 0 -2
- The DME will return two lines of character strings if it succeeds.
The first line will have the character string "RRSC OK."
For details on the character string "SCN" in the second line, see chapter 3.2.1.
The first line can be ignored; check the second line to find if a scene is recalled for a controller.
A scene number after scene recall should be returned in the second line (absolute quantity).
Even relative recall will not return the quantity changed.
- The DME will return a one-line character string of "RRSC ERR" if it fails.
E.g.) ACK when the current scene is "3" and it succeeds in recalling the next scene.
RRSC OK
SCN 0 4
ACK when the current scene is "3" and it fails in recalling the next scene.
RRSC ERR
16) GCS: Used to obtain a current scene number.
The DME's ACKs when it succeeds
GCS OK
CSN 0 [scene number]
The command name stands for "Get Current Scene".
GCS
Option
0
The DME's ACKs when it fails
GCS ERR
This command will enable the user to obtain a scene number currently being recalled for the DME using the controller.
- The option will always take "0." It is reserved for future extensions to the command.
- One or more spaces will be needed between the command and the option.
E.g.) To obtain a current scene number:
GCS 0
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string, "GCS OK".
The second line will have a character string, "SCN [scene number]", and ｔhe [scene number] takes either a scene
number from 1 to 999 or number 0.
The scene number 0 indicates that a scene has not been recalled (no current scene).
The first character string can be ignored for the controller.
- The DME will return a one-line character string of "GCS ERR" if it fails.
E.g.) ACK when it returns Scene 4 by obtaining a current scene number.
GCS OK
CSN 0 4
(The character string stands for "Current Scene Number".)
ACK when "no scene" is returned by obtaining a current scene number:
GCS OK
CSN 0 0
ACK when it fails in obtaining a current scene number.
GCS ERR
DME Remote Control Protocol Specifications V3.1
10
17) GSN: Used to obtain a scene name.
The DME's ACKs when it succeeds
GSN OK
SNM 0 [scene number] [a scene name]
The command name stands for "Get Scene Name."
GSN
Option
0 [scene number]
The DME's ACKs when it fails
GSN ERR
This command will enable the user to obtain a DME scene name of a specified number from the controller.
- The first option will always take "0." It is reserved for future extensions to the command.
- [scene number] will have an appropriate number converted to a character string.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To obtain Scene 4 name:
GSN 0 4
- The DME will return two lines of character strings if it succeeds.
The first line will have the character string "GSN OK."
The second line will have a scene number from 1 to 999 for the [scene number] and a new name for the [a scene
name] by a character string.
The first character string can be ignored for the controller.
A scene name that is blank looks as a scene name is not returned.
- The DME will return one line of a character string; "GSN ERR" if it fails.
E.g.) ACK when a character string, "Scene 004" is returned by obtaining a name of Scene 4.
GSN OK
SNM 4 Scene 004
(The character string stands for "Scene NaMe".)
ACK when a character string, " " is returned by obtaining a name of Scene 4.
GSN OK
SNM 4
ACK when it fails in obtaining a name of Scene 4.
GSN ERR
3.3.3 Command to Obtain Level Meter
18) GMT: Used to obtain a level meter position.
GMT
Option
0 [index] [a meter value]
The DME's ACKs when it succeeds
GMT OK
MTR 0 [index] CUR [CH1] … HOLD [CH1] …
The DME's ACKs when it fails
GMT ERR
The command name stands for "Get Meter."
CUR stands for "Current meter value".
HOLD stands for "Peak hold value".
This command will enable the user to obtain a DME meter value.
- The first option will always take "0." It is reserved for future extensions to the command.
- [index] will have an appropriate number converted to a character string.
- The meter number to be obtained should be assigned to [a meter number].
A value of "1" or greater should be assigned to a meter number to obtain specific meter data.
See "DME Communication Protocol Specifications" for the meter numbers for each component.
A value of "0" should be assigned to obtain meter data for every channel.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To obtain a level meter for a specific channel (index 1, parameter number 3)
GMT 0 1 3
E.g.) To obtain a level meter for every channel (index 1, parameter number 0)
GMT 0 1 0
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string of "GMT OK."
The second line will have a character string of "MTR [index] CUR [CH1] [CH2] … HOLD [CH1] [CH2] … ".
The first character string can be ignored for the controller.
The same number of current meter levels as that of channels comes after CUR in the second line.
The same number of current meter hold levels as that of channels comes after HOLD in the second line.
The meter and hold level number ranges from -13801 to 1.
The following table shows the relationship between character strings and levels sent from the DME.
DME Remote Control Protocol Specifications V3.1
11
Character strings
-13801
-13800
-10000
-8000
-6000
-4000
-2000
0
1
Level
-Inf
-138dB
-100dB
-80dB
-60dB
-40dB
-20dB
0dB
Over
To detect if an input level to the Audio Detector exceeds the threshold
If an input level to the Audio Detector exceeds the threshold, the meter level becomes "Over," which
is different from conventional meter operation. Obtaining the character string "MTR 0 1 0 CUR 1
HOLD 1" indicates that the input level exceeds the threshold.
- The DME will return the one-line character string "GMT ERR" if it fails.
E.g.) ACK when it succeeds in obtaining a meter of an index of 5 (four channels) (The numbers below are examples)
GMT OK
MTR 0 5 CUR -13801 -2000 -3000 -13801 HOLD -13801 -1500 -2800 -13801
(The character string stands for "MeTeR".)
ACK when it succeeds in obtaining a meter of an index of 5 (eight channels) (The numbers below are examples)
GMT OK
MTR 0 5 CUR -1800 -2300 -200 1 -300 0 -13801 -13801 HOLD -1500 -2000 -0 1 -200 1 -13801 -13801
ACK when it fails in obtaining a meter of an index of 5 (four channels)
GMT ERR
19) GCMT: Used to set cyclical obtaining of a level meter.
The DME's ACKs when it succeeds
GCMT OK
MTR 0 [index] CUR [CH1] … HOLD [CH1] …
The command name stands for "Get Cyclic Meter".
CUR stands for "Current meter value".
HOLD stands for "Peak hold value".
GCMT
Option
0 [index] [a meter value]
The DME's ACKs when it fails
GCMT ERR
Registering a meter number to be obtained using this command will send the level meter value cyclically from the DME.
The level meter value will be sent until it is cancelled with a QCMT command described later. Up to 100 meters can be registered.
- The first option will always take "0." It is reserved for future extensions to the command.
- The same as [index] GMT.
- The same as [a meter number] GMT.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To register cyclical obtaining of a level meter for a specific channel (index 1, parameter number 3)
GCMT 0 1 3
E.g.) To register cyclical obtaining of a level meter for every channel (index 1, parameter number 0)
GCMT 0 1 0
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string of "GCMT OK."
The second line will have the same character string as ACK when obtaining a meter using GMT.
- The DME will return a one-line character string of "GCMT ERR" if it fails.
E.g.) An example of the DME transmit and receive data when assigning a specific channel (index: 1, meter number: 3)
GCMT 0 1 3
MTR 0 1 CUR -1800 HOLD 0
：
(Remote Controller will receive meter data cyclically from the DME.)
MTR 0 1 CUR -1700 HOLD 0
E.g.) An example of transmit and receive data when assigning all channels (index 1, meter number: 0)
GCMT 0 1 0
MTR 0 1 CUR -1800 -2300 -200 1 -300 0 -13801 -13801 HOLD 0 0 0 0 0 10
：
(Remote Controller will receive meter data cyclically from the DME.)
MTR 0 1 CUR -1800 -2300 -200 1 -300 0 -13801 -13801 HOLD 0 0 0 0 0 10
DME Remote Control Protocol Specifications V3.1
12
20) QCMT: Used to stop cyclical obtaining of a level meter.
QCMT
Option
0 [index] [a meter value]
The DME's ACKs when it succeeds
QCMT OK
The DME's ACKs when it fails
QCMT ERR
The command name stands for "Quit Cyclic Meter".
It will be used to cancel cyclic transmission of a level meter registered in the DME with the GCMT command.
- The first option will always take "0." It is reserved for future extensions to the command.
- [index] will have an appropriate number assigned with the DME Designer by a character string.
- "0" should be always assigned to [a meter number].
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To discard registration of an obtained meter cycle:
QCMT 0 1 0
The DME will return a one-line character string of "QCMT OK" if it succeeds.
The DME will return a one-line character string of "QCMT ERR" if it fails.
E.g.) ACK when it succeeds in discarding meter number registration.
QCMT OK
ACK when it fails in discarding meter number registration.
QCMT ERR
21) SMC: Used to set the cyclical period for automatically obtaining all level meters.
SMC
Option
0 [a cycle]
The DME's ACKs when it succeeds
SMC OK
The DME's ACKs when it fails
SMC ERR
The command name stands for "Set Meter Cycle".
This command will enable the user to set a cycle in ms units for sending all level meters set to be obtained cyclically.
The DME will send level meters at 100 msec intervals if the DME has not received this command.
- The first option will always take "0." It is reserved for future extensions to the command.
- The meter transmission interval from the DME should be assigned to [a cycle] in ms units.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To change the meter transmission interval from the DME to 200msec:
SMC 0 200
- The DME will return a one-line character string of "SMC OK" if it succeeds.
- The DME will return a one-line character string of "SMC ERR" if it fails.
E.g.) ACK when it succeeds in changing the meter transmission interval:
SMC OK
ACK when it fails in changing the meter transmission interval:
SMC ERR
Guide for setting the cycle
An appropriate cycle needs to be set in accordance with the number of the level meters to be obtained cyclically.
Follow the table below to find an appropriate cycle.
A table of the number of the level meters and the required time to be obtained
Number of level meters to be
Required time
obtained by a single command to be obtained
64
239ms
32
122ms
16
64ms
8
34ms
4
20ms
2
12ms
1
9ms
The sum of "Required time to be obtained" in the table above for each command will be the guide for setting an appropriate cycle.
The cycle to automatically obtain a level meter, however, should be set to at least at 50 msec, since too short of a cycle will
increase the load of the communication line.
DME Remote Control Protocol Specifications V3.1
13
Estimation of the cycle:
Example 1: To obtain 1 ch level meter of 16ch Fader component,
A required cycle for obtaining 1 level meter is 9 ms according to the table above.
However, since the minimum cycle must be at least 50 ms, set the cycle to 50 ms.
Example 2: To obtain 1 component (16 ch) level meters of 16ch Fader component,
A required cycle for obtaining 16 level meters is 64 ms according to the table above.
Set the cycle to 64 ms.
Example 3: To obtain 2 component (32 ch) level meters of 16ch Fader component,
A required cycle for obtaining 16 level meters is 64 ms according to the table above.
Set the cycle to 128 ms by multiplying 64 ms by 2 component cycles.
3.3.4 Mute Control Command
22) SMUT: Used to set/cancel the mute function.
The DME's ACKs when it succeeds
SMUT OK
MUTE 0 [ON/OFF]
The command name stands for "Set Mute".
SMUT
Option
0 [ON/OFF]
The DME's ACKs when it fails
SMUT ERR
- The first option will always take "0." It is reserved for future extensions to the command.
- The second option will have a character string of either "ON" or "OFF."
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To turn on the mute function:
SMUT 0 ON
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string of "SMUT OK."
The second line will have the same character string as that output to the controller from the DME when Mute ON/OFF
is switched.
The first character string can be ignored for the controller.
- The DME will return a character string of "SMUT ERR" if it fails.
E.g.) ACK when it succeeds in switching the mute function on:
SMUT OK
MUTE 0 ON
ACK when it fails in switching the mute function on:
SMUT ERR
23) GMUT: Used to obtain the mute condition.
The DME's ACKs when it succeeds
GMUT OK
MUTE 0 [ON/OFF]
The command name stands for "Get Mute."
This command only applies to DME firmware V3.11 or later.
GMUT
Option
0
The DME's ACKs when it fails
GMUT ERR
- The option will always take "0." It is reserved for future extensions to the command.
- One or more spaces will be needed between the command and the option.
E.g.) To obtain the mute condition:
GMUT 0
- The DME will return two lines of character strings if it succeeds.
The first line will have a character string, "GMUT OK."
The second line will have the same character string as that output to the controller from the DME when Mute ON/OFF
is switched.
The first character string can be ignored for the controller.
- The DME will return a one-line character string of "GMUT ERR" if it fails.
E.g.) ACK when it succeeds in obtaining the mute condition and the mute condition is ON:
GMUT OK
MUTE 0 ON
ACK when it fails in obtaining the mute condition:
GMUT ERR
DME Remote Control Protocol Specifications V3.1
14
3.3.5 GPI Control Command
24) SGO: Used to control GPI OUT.
SGO
Option
0 [Port number] [ON/OFF] …
The DME's ACKs when it succeeds
SGO OK
The DME's ACKs when it fails
SGO ERR
The command name stands for "Set Gpi Out".
- The first option will always take "0." It is reserved for future extensions to the command.
- The second option will have a port number by a character string.
- The third option will have a character string of either "ON" or "OFF."
- One or more spaces are needed between the command and the option, and between the options.
- Multiple GPI outputs can be controlled by adding another option.
- SGO command changes GPI OUT port status without affecting any parameters in DME components.
E.g.) To set port 3 on:
SGO 0 3 ON
To set port 10 on, port 11 off:
SGO 0 10 ON 11 OFF
To set port 1 on, port 3 off, port 4 on and port 5 on:
SGO 0 1 ON 3 OFF 4 ON 5 ON
- The DME will return a one-line character string of "SGO OK" if it succeeds.
- The DME will return a one-line character string of "SGO ERR" if it fails.
E.g.) ACK when it succeeds in setting GPI port 3 on:
SGO OK
ACK when it fails in setting GPI port 3 on:
SGO ERR
3.3.6 WAV FILE PLAYER Control Command
25) PWF: Used to play back a file.
PWF
Option
0 [An index to Wav File Manager]
The DME's ACKs when it succeeds
PWF OK
The DME's ACKs when it fails
PWF ERR
The command name stands for "Play Wav File".
This command will enable the user to play back a specified song in the DME's WAV File Player.
A file should be registered in WAV File Manager in advance to play the song.
- The first option will always take "0." It is reserved for future extensions to the command.
- The second option will have an index to Wav File Manager by a character string.
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To play back a WAV file registered in Wav File Manager 4:
PWF 0 4
- The DME will return a one-line character string of "PWF OK" if it succeeds.
- The DME will return a one-line character string of "PWF ERR" if it fails.
E.g.) ACK when it succeeds in playing back a WAV file registered in Wav File Manager 4:
PWF OK
ACK when it fails in playing back a WAV file registered in Wav File Manager 4:
PWF ERR
DME Remote Control Protocol Specifications V3.1
15
26) SWF: Used to stop playback of a file.
SWF
Option
0
The DME's ACKs when it succeeds
SWF OK
The DME's ACKs when it fails
SWF ERR
The command name stands for "Stop Wav File."
This command only applies to DME firmware V3.11 or later.
This command will enable the user to stop playback of a song in the DME's WAV File Player.
- The option will always take "0." It is reserved for future extensions to the command.
- One or more spaces are needed between the command and the option.
E.g.) To stop playback of a WAV file
SWF 0
- The DME will return a one-line character string of "SWF OK" if it succeeds.
- The DME will return a one-line character string of "SWF ERR" if it fails.
E.g.) ACK when it succeeds in stopping playback of a WAV file:
SWF OK
ACK when it fails in stopping playback of a WAV file:
SWF ERR
3.4 Utility Command
3.4.1 Command for Debug
27) ECHO: Used to set/cancel Echo Back.
Command Option
ECHO
0 [ON/OFF]
The DME's ACKs when it succeeds
ECHO OK
The DME's ACKs when it fails
ECHO ERR
A character string received by the DME can be echoed back to debug the controller.
Switching the Echo function on will cause a character string to be echoed back until the Echo function or the DME is switched off.
The default is OFF.
It may be controlled normally while it is echoed back.
- The first option will always take "0." It is reserved for future extensions to the command.
- [ON/OFF] will have a character string of either "ON" or "OFF."
- One or more spaces are needed between the command and the option, and between the options.
E.g.) To switch the DME Echo on:
ECHO 0 ON
To switch the DME Echo off:
ECHO 0 OFF
A character string of "ECHO OK" will be output to the controller when it succeeds, or "ECHO ERR" when it fails.
DME Remote Control Protocol Specifications V3.1
16
4. Command Sequence
The following are examples of the main command sequence.
A parameter change (executed by Remote Controller)
A parameter set command
DME
SPR 0 1 0 (setting parameter 1 to 0)
Remote Controller
SPR OK (ACK from the DME)
PRM 0 1 0 (parameter 1 is set to 0)
A parameter change (executed by other than Remote Controller)
DME
A parameter set command
Remote Controller
PRM 0 1 0 (parameter 1 is set to 0)
Obtaining a parameter
DME
GPR 0 1 (obtaining parameter 1)
Remote Controller
GPR OK (ACK from the DME)
PRM 0 1 0 (current value for parameter 1 is 0)
Scene recall (executed by Remote Controller)
DME
RSC 0 1 (recalling scene 1)
Remote Controller
RSC OK (ACK from the DME)
SCN 0 1 (scene 1 is recalled)
Scene recall (executed by other than Remote Controller)
DME
Remote Controller
SCN 0 1 (scene 1 is recalled)
Obtaining current scene information
DME
GCS (obtaining the current scene number)
Remote Controller
GCS OK (ACK from the DME)
CSN 0 1 ("1" is the current scene)
Command to obtain a level meter
DME
GMT 0 1
(obtaining a meter registered in "1")
Remote Controller
GMT OK (ACK from the DME)
MTR 0 1 -100 -500 -200 …
(meter registered in "1" is obtained)
DME Remote Control Protocol Specifications V3.1
17
Registration to obtain level meter cycle
SMC 0 500
(setting the cycle for obtaining the meter to 500 msec)
DME
SMC OK
GCMT 0 1 0
(cyclically obtaining every meter registered in "1")
GCMT OK
Remote Controller
MTR 0 1 CUR -100 -500 -200 …
(obtaining a meter registered in "1")
MTR 0 1 CUR -100 -500 -200 …
(obtaining a meter registered in "1")
500msec
：
：
：
QCMT 0 1 0
(stopping the cyclical process of obtaining a component meter registered in "1")
QCMT OK
Mute Control
DME
SMUT 0 ON
(turning mute on)
Remote Controller
SMUT OK
MUTE 0 ON
(notifying that the mute function is turned on)
Obtaining mute condition
DME
GMUT 0
（obtaining mute condition）
Remote Controller
GMUT OK
MUTE 0 ON
（notifying that the mute condition is on)
GPI OUT Control
DME
Remote Controller
SGO 0 1 ON 2 OFF 3 ON
(turning GPI OUT CH1 on, CH2 off and CH3 on)
SGO OK
Playing Back WAV file
DME
Remote Controller
PWF 0 1
(playing back a file registered in WAV File Manager 1)
PWF OK
Stopping playback of a WAV file
DME
Remote Controller
SWF 0
(stopping playback of a WAV file)
SWF OK
DME Remote Control Protocol Specifications V3.1
18
Troubleshooting (FAQ)
Q: Is it possible to communicate with the DME at a baud rate other than 38400bps for serial communication via the REMOTE
connector?
A: No, it is not possible. Be sure to set the baud rate of the remote controller to 38400bps.
For more information, see the section "1.2 Remote Controller Settings."
Q: What should be used as a line feed code of a command?
A: LF (0x0A) can be used as a line feed code ("$0A" for AMX, "\x0A" for Crestron).
For more information, see the section "3.1 Basic Command Specifications."
Q: Up to how many parameters can be controlled with the communication protocol?
A: The maximum number of specifically defined controllable parameters is 256, as set in the Remote Control Setup List of DME Designer.
Other controls such as scene recall are in addition to this.
Q: How can I control more than 256 types of parameters?
A: You can use MIDI and/or GPI signals in addition to the remote control protocol.
Q: Can the MIDI parameter change and/or control change be transmitted via Ethernet?
A: No, the MIDI parameter change and/or control change cannot be transmitted via Ethernet.
The SPR command can be used to change parameters. The RSC command can be used to recall a scene.
Q: Can the DME receive the parameter setting command SPR in the middle of scene recall processing?
A: No, the command is disabled during recall. All the commands transmitted to the DME in the middle of scene recall processing will be
ignored. When scene recalls are complete, the DME will restart receiving the SPR command.
The parameter setting command can be transmitted after checking the SCN command notified from the DME when scene recalls
are complete.
Q: Is there any difference in response time for parameter changing, depending on the type of component?
A: A component (such as Matrix Mixer 64x64) with various parameters may require longer time for parameter change than a
component with a small number of parameters.
Q: If the response speed of the DME to a command is slow, what are the possible causes and solutions?
A: When a large number of commands are transmitted to the DME in a short time, processing time may be longer because data is
accumulated in the receive buffer.
In this case, make sure that the transmission interval between the commands for the remote controller is long enough for optimum
processing.
Q: If the response speed of the meter is slow, what are the possible causes and solutions?
A: The response speed of the meter will be slow when the number of meters displayed on the screen increases.
In this case, try the following solutions.
・If the cyclical period for automatically obtaining a meter is too short, the response speed will be slow due to the accumulation of
data. Try to set a cycle as long as possible using the SMC command.
・The response speed will be faster by using the GCMT command that can obtain data cyclically than by using the GMT command
that obtains data each time, because the volume of communication decreases.
・If you want to display multiple meters in the same component, you can ensure a faster response speed by assigning a value of "0"
to a meter number to obtain data all at once, rather than by assigning a meter number to obtain data individually.
・If you want to display a meter in the Meter component, you can ensure a faster response speed by assigning the multiple-channel
Meter component, rather than by assigning multiple one-channel Meter components.
For more information on commands see GMT and GCMT in the section "3.3.3 Command to Obtain Level Meter."
Q: If a parameter is assigned to "GPI OUT" and the port is controlled by the SGO command, does the parameter link?
A: No, the parameter does not link.
Only the GPI output from a port specified by the SGO command is controlled.
Q: Can the input level to the Audio Detector be detected if it exceeds the threshold?
A: Yes it can.
For more information on detecting the level see the section "3.3.3 Command to Obtain Level Meter."
DME Remote Control Protocol Specifications V3.1
19
Appendix
A Fader Table of -∞ to 0 dB
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Data
Value
-InfdB
64
-138.00dB
65
-136.00dB
66
-134.00dB
67
-133.00dB
68
-132.00dB
69
-131.00dB
70
-130.00dB
71
-129.00dB
72
-128.00dB
73
-127.00dB
74
-126.00dB
75
-125.00dB
76
-124.00dB
77
-123.00dB
78
-122.00dB
79
-121.00dB
80
-120.00dB
81
-119.00dB
82
-118.00dB
83
-117.00dB
84
-116.00dB
85
-115.00dB
86
-114.00dB
87
-113.00dB
88
-112.00dB
89
-111.00dB
90
-110.00dB
91
-109.00dB
92
-108.00dB
93
-107.00dB
94
-106.00dB
95
-105.00dB
96
-104.00dB
97
-103.00dB
98
-102.00dB
99
-101.50dB 100
-101.00dB 101
-100.50dB 102
-100.00dB 103
-99.50dB
104
-99.00dB
105
-98.50dB
106
-98.00dB
107
-97.50dB
108
-97.00dB
109
-96.50dB
110
-96.00dB
111
-95.50dB
112
-95.00dB
113
-94.50dB
114
-94.00dB
115
-93.50dB
116
-93.00dB
117
-92.50dB
118
-92.00dB
119
-91.50dB
120
-91.00dB
121
-90.50dB
122
-90.00dB
123
-89.50dB
124
-89.00dB
125
-88.50dB
126
-88.00dB
127
Data
-87.50dB
-87.00dB
-86.50dB
-86.00dB
-85.50dB
-85.00dB
-84.50dB
-84.00dB
-83.50dB
-83.00dB
-82.50dB
-82.00dB
-81.50dB
-81.00dB
-80.50dB
-80.00dB
-79.50dB
-79.00dB
-78.50dB
-78.00dB
-77.80dB
-77.60dB
-77.40dB
-77.20dB
-77.00dB
-76.80dB
-76.60dB
-76.40dB
-76.20dB
-76.00dB
-75.80dB
-75.60dB
-75.40dB
-75.20dB
-75.00dB
-74.80dB
-74.60dB
-74.40dB
-74.20dB
-74.00dB
-73.80dB
-73.60dB
-73.40dB
-73.20dB
-73.00dB
-72.80dB
-72.60dB
-72.40dB
-72.20dB
-72.00dB
-71.80dB
-71.60dB
-71.40dB
-71.20dB
-71.00dB
-70.80dB
-70.60dB
-70.40dB
-70.20dB
-70.00dB
-69.80dB
-69.60dB
-69.40dB
-69.20dB
Value
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Data
-69.00dB
-68.80dB
-68.60dB
-68.40dB
-68.20dB
-68.00dB
-67.80dB
-67.60dB
-67.40dB
-67.20dB
-67.00dB
-66.80dB
-66.60dB
-66.40dB
-66.20dB
-66.00dB
-65.80dB
-65.60dB
-65.40dB
-65.20dB
-65.00dB
-64.80dB
-64.60dB
-64.40dB
-64.20dB
-64.00dB
-63.80dB
-63.60dB
-63.40dB
-63.20dB
-63.00dB
-62.80dB
-62.60dB
-62.40dB
-62.20dB
-62.00dB
-61.80dB
-61.60dB
-61.40dB
-61.20dB
-61.00dB
-60.80dB
-60.60dB
-60.40dB
-60.20dB
-60.00dB
-59.80dB
-59.60dB
-59.40dB
-59.20dB
-59.00dB
-58.80dB
-58.60dB
-58.40dB
-58.20dB
-58.00dB
-57.80dB
-57.60dB
-57.40dB
-57.20dB
-57.00dB
-56.80dB
-56.60dB
-56.40dB
Value
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
Data
-56.20dB
-56.00dB
-55.80dB
-55.60dB
-55.40dB
-55.20dB
-55.00dB
-54.80dB
-54.60dB
-54.40dB
-54.20dB
-54.00dB
-53.80dB
-53.60dB
-53.40dB
-53.20dB
-53.00dB
-52.80dB
-52.60dB
-52.40dB
-52.20dB
-52.00dB
-51.80dB
-51.60dB
-51.40dB
-51.20dB
-51.00dB
-50.80dB
-50.60dB
-50.40dB
-50.20dB
-50.00dB
-49.90dB
-49.80dB
-49.70dB
-49.60dB
-49.50dB
-49.40dB
-49.30dB
-49.20dB
-49.10dB
-49.00dB
-48.90dB
-48.80dB
-48.70dB
-48.60dB
-48.50dB
-48.40dB
-48.30dB
-48.20dB
-48.10dB
-48.00dB
-47.90dB
-47.80dB
-47.70dB
-47.60dB
-47.50dB
-47.40dB
-47.30dB
-47.20dB
-47.10dB
-47.00dB
-46.90dB
-46.80dB
Value
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
Data
-46.70dB
-46.60dB
-46.50dB
-46.40dB
-46.30dB
-46.20dB
-46.10dB
-46.00dB
-45.90dB
-45.80dB
-45.70dB
-45.60dB
-45.50dB
-45.40dB
-45.30dB
-45.20dB
-45.10dB
-45.00dB
-44.90dB
-44.80dB
-44.70dB
-44.60dB
-44.50dB
-44.40dB
-44.30dB
-44.20dB
-44.10dB
-44.00dB
-43.90dB
-43.80dB
-43.70dB
-43.60dB
-43.50dB
-43.40dB
-43.30dB
-43.20dB
-43.10dB
-43.00dB
-42.90dB
-42.80dB
-42.70dB
-42.60dB
-42.50dB
-42.40dB
-42.30dB
-42.20dB
-42.10dB
-42.00dB
-41.90dB
-41.80dB
-41.70dB
-41.60dB
-41.50dB
-41.40dB
-41.30dB
-41.20dB
-41.10dB
-41.00dB
-40.90dB
-40.80dB
-40.70dB
-40.60dB
-40.50dB
-40.40dB
Value
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
Data
-40.30dB
-40.20dB
-40.10dB
-40.00dB
-39.90dB
-39.80dB
-39.70dB
-39.60dB
-39.50dB
-39.40dB
-39.30dB
-39.20dB
-39.10dB
-39.00dB
-38.90dB
-38.80dB
-38.70dB
-38.60dB
-38.50dB
-38.40dB
-38.30dB
-38.20dB
-38.10dB
-38.00dB
-37.90dB
-37.80dB
-37.70dB
-37.60dB
-37.50dB
-37.40dB
-37.30dB
-37.20dB
-37.10dB
-37.00dB
-36.90dB
-36.80dB
-36.70dB
-36.60dB
-36.50dB
-36.40dB
-36.30dB
-36.20dB
-36.10dB
-36.00dB
-35.90dB
-35.80dB
-35.70dB
-35.60dB
-35.50dB
-35.40dB
-35.30dB
-35.20dB
-35.10dB
-35.00dB
-34.90dB
-34.80dB
-34.70dB
-34.60dB
-34.50dB
-34.40dB
-34.30dB
-34.20dB
-34.10dB
-34.00dB
DME Remote Control Protocol Specifications V3.1
Value
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
Data
-33.90dB
-33.80dB
-33.70dB
-33.60dB
-33.50dB
-33.40dB
-33.30dB
-33.20dB
-33.10dB
-33.00dB
-32.90dB
-32.80dB
-32.70dB
-32.60dB
-32.50dB
-32.40dB
-32.30dB
-32.20dB
-32.10dB
-32.00dB
-31.90dB
-31.80dB
-31.70dB
-31.60dB
-31.50dB
-31.40dB
-31.30dB
-31.20dB
-31.10dB
-31.00dB
-30.90dB
-30.80dB
-30.70dB
-30.60dB
-30.50dB
-30.40dB
-30.30dB
-30.20dB
-30.10dB
-30.00dB
-29.95dB
-29.90dB
-29.85dB
-29.80dB
-29.75dB
-29.70dB
-29.65dB
-29.60dB
-29.55dB
-29.50dB
-29.45dB
-29.40dB
-29.35dB
-29.30dB
-29.25dB
-29.20dB
-29.15dB
-29.10dB
-29.05dB
-29.00dB
-28.95dB
-28.90dB
-28.85dB
-28.80dB
Value
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
Data
-28.75dB
-28.70dB
-28.65dB
-28.60dB
-28.55dB
-28.50dB
-28.45dB
-28.40dB
-28.35dB
-28.30dB
-28.25dB
-28.20dB
-28.15dB
-28.10dB
-28.05dB
-28.00dB
-27.95dB
-27.90dB
-27.85dB
-27.80dB
-27.75dB
-27.70dB
-27.65dB
-27.60dB
-27.55dB
-27.50dB
-27.45dB
-27.40dB
-27.35dB
-27.30dB
-27.25dB
-27.20dB
-27.15dB
-27.10dB
-27.05dB
-27.00dB
-26.95dB
-26.90dB
-26.85dB
-26.80dB
-26.75dB
-26.70dB
-26.65dB
-26.60dB
-26.55dB
-26.50dB
-26.45dB
-26.40dB
-26.35dB
-26.30dB
-26.25dB
-26.20dB
-26.15dB
-26.10dB
-26.05dB
-26.00dB
-25.95dB
-25.90dB
-25.85dB
-25.80dB
-25.75dB
-25.70dB
-25.65dB
-25.60dB
20
Value
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
Data
-25.55dB
-25.50dB
-25.45dB
-25.40dB
-25.35dB
-25.30dB
-25.25dB
-25.20dB
-25.15dB
-25.10dB
-25.05dB
-25.00dB
-24.95dB
-24.90dB
-24.85dB
-24.80dB
-24.75dB
-24.70dB
-24.65dB
-24.60dB
-24.55dB
-24.50dB
-24.45dB
-24.40dB
-24.35dB
-24.30dB
-24.25dB
-24.20dB
-24.15dB
-24.10dB
-24.05dB
-24.00dB
-23.95dB
-23.90dB
-23.85dB
-23.80dB
-23.75dB
-23.70dB
-23.65dB
-23.60dB
-23.55dB
-23.50dB
-23.45dB
-23.40dB
-23.35dB
-23.30dB
-23.25dB
-23.20dB
-23.15dB
-23.10dB
-23.05dB
-23.00dB
-22.95dB
-22.90dB
-22.85dB
-22.80dB
-22.75dB
-22.70dB
-22.65dB
-22.60dB
-22.55dB
-22.50dB
-22.45dB
-22.40dB
Value
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
Data
-22.35dB
-22.30dB
-22.25dB
-22.20dB
-22.15dB
-22.10dB
-22.05dB
-22.00dB
-21.95dB
-21.90dB
-21.85dB
-21.80dB
-21.75dB
-21.70dB
-21.65dB
-21.60dB
-21.55dB
-21.50dB
-21.45dB
-21.40dB
-21.35dB
-21.30dB
-21.25dB
-21.20dB
-21.15dB
-21.10dB
-21.05dB
-21.00dB
-20.95dB
-20.90dB
-20.85dB
-20.80dB
-20.75dB
-20.70dB
-20.65dB
-20.60dB
-20.55dB
-20.50dB
-20.45dB
-20.40dB
-20.35dB
-20.30dB
-20.25dB
-20.20dB
-20.15dB
-20.10dB
-20.05dB
-20.00dB
-19.95dB
-19.90dB
-19.85dB
-19.80dB
-19.75dB
-19.70dB
-19.65dB
-19.60dB
-19.55dB
-19.50dB
-19.45dB
-19.40dB
-19.35dB
-19.30dB
-19.25dB
-19.20dB
Value
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
Data
-19.15dB
-19.10dB
-19.05dB
-19.00dB
-18.95dB
-18.90dB
-18.85dB
-18.80dB
-18.75dB
-18.70dB
-18.65dB
-18.60dB
-18.55dB
-18.50dB
-18.45dB
-18.40dB
-18.35dB
-18.30dB
-18.25dB
-18.20dB
-18.15dB
-18.10dB
-18.05dB
-18.00dB
-17.95dB
-17.90dB
-17.85dB
-17.80dB
-17.75dB
-17.70dB
-17.65dB
-17.60dB
-17.55dB
-17.50dB
-17.45dB
-17.40dB
-17.35dB
-17.30dB
-17.25dB
-17.20dB
-17.15dB
-17.10dB
-17.05dB
-17.00dB
-16.95dB
-16.90dB
-16.85dB
-16.80dB
-16.75dB
-16.70dB
-16.65dB
-16.60dB
-16.55dB
-16.50dB
-16.45dB
-16.40dB
-16.35dB
-16.30dB
-16.25dB
-16.20dB
-16.15dB
-16.10dB
-16.05dB
-16.00dB
Value
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
Data
-15.95dB
-15.90dB
-15.85dB
-15.80dB
-15.75dB
-15.70dB
-15.65dB
-15.60dB
-15.55dB
-15.50dB
-15.45dB
-15.40dB
-15.35dB
-15.30dB
-15.25dB
-15.20dB
-15.15dB
-15.10dB
-15.05dB
-15.00dB
-14.95dB
-14.90dB
-14.85dB
-14.80dB
-14.75dB
-14.70dB
-14.65dB
-14.60dB
-14.55dB
-14.50dB
-14.45dB
-14.40dB
-14.35dB
-14.30dB
-14.25dB
-14.20dB
-14.15dB
-14.10dB
-14.05dB
-14.00dB
-13.95dB
-13.90dB
-13.85dB
-13.80dB
-13.75dB
-13.70dB
-13.65dB
-13.60dB
-13.55dB
-13.50dB
-13.45dB
-13.40dB
-13.35dB
-13.30dB
-13.25dB
-13.20dB
-13.15dB
-13.10dB
-13.05dB
-13.00dB
-12.95dB
-12.90dB
-12.85dB
-12.80dB
Value
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
Data
-12.75dB
-12.70dB
-12.65dB
-12.60dB
-12.55dB
-12.50dB
-12.45dB
-12.40dB
-12.35dB
-12.30dB
-12.25dB
-12.20dB
-12.15dB
-12.10dB
-12.05dB
-12.00dB
-11.95dB
-11.90dB
-11.85dB
-11.80dB
-11.75dB
-11.70dB
-11.65dB
-11.60dB
-11.55dB
-11.50dB
-11.45dB
-11.40dB
-11.35dB
-11.30dB
-11.25dB
-11.20dB
-11.15dB
-11.10dB
-11.05dB
-11.00dB
-10.95dB
-10.90dB
-10.85dB
-10.80dB
-10.75dB
-10.70dB
-10.65dB
-10.60dB
-10.55dB
-10.50dB
-10.45dB
-10.40dB
-10.35dB
-10.30dB
-10.25dB
-10.20dB
-10.15dB
-10.10dB
-10.05dB
-10.00dB
-9.95dB
-9.90dB
-9.85dB
-9.80dB
-9.75dB
-9.70dB
-9.65dB
-9.60dB
Value
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
Data
-9.55dB
-9.50dB
-9.45dB
-9.40dB
-9.35dB
-9.30dB
-9.25dB
-9.20dB
-9.15dB
-9.10dB
-9.05dB
-9.00dB
-8.95dB
-8.90dB
-8.85dB
-8.80dB
-8.75dB
-8.70dB
-8.65dB
-8.60dB
-8.55dB
-8.50dB
-8.45dB
-8.40dB
-8.35dB
-8.30dB
-8.25dB
-8.20dB
-8.15dB
-8.10dB
-8.05dB
-8.00dB
-7.95dB
-7.90dB
-7.85dB
-7.80dB
-7.75dB
-7.70dB
-7.65dB
-7.60dB
-7.55dB
-7.50dB
-7.45dB
-7.40dB
-7.35dB
-7.30dB
-7.25dB
-7.20dB
-7.15dB
-7.10dB
-7.05dB
-7.00dB
-6.95dB
-6.90dB
-6.85dB
-6.80dB
-6.75dB
-6.70dB
-6.65dB
-6.60dB
-6.55dB
-6.50dB
-6.45dB
-6.40dB
DME Remote Control Protocol Specifications V3.1
Value
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
Data
-6.35dB
-6.30dB
-6.25dB
-6.20dB
-6.15dB
-6.10dB
-6.05dB
-6.00dB
-5.95dB
-5.90dB
-5.85dB
-5.80dB
-5.75dB
-5.70dB
-5.65dB
-5.60dB
-5.55dB
-5.50dB
-5.45dB
-5.40dB
-5.35dB
-5.30dB
-5.25dB
-5.20dB
-5.15dB
-5.10dB
-5.05dB
-5.00dB
-4.95dB
-4.90dB
-4.85dB
-4.80dB
-4.75dB
-4.70dB
-4.65dB
-4.60dB
-4.55dB
-4.50dB
-4.45dB
-4.40dB
-4.35dB
-4.30dB
-4.25dB
-4.20dB
-4.15dB
-4.10dB
-4.05dB
-4.00dB
-3.95dB
-3.90dB
-3.85dB
-3.80dB
-3.75dB
-3.70dB
-3.65dB
-3.60dB
-3.55dB
-3.50dB
-3.45dB
-3.40dB
-3.35dB
-3.30dB
-3.25dB
-3.20dB
Value
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
Data
-3.15dB
-3.10dB
-3.05dB
-3.00dB
-2.95dB
-2.90dB
-2.85dB
-2.80dB
-2.75dB
-2.70dB
-2.65dB
-2.60dB
-2.55dB
-2.50dB
-2.45dB
-2.40dB
-2.35dB
-2.30dB
-2.25dB
-2.20dB
-2.15dB
-2.10dB
-2.05dB
-2.00dB
-1.95dB
-1.90dB
-1.85dB
-1.80dB
-1.75dB
-1.70dB
-1.65dB
-1.60dB
-1.55dB
-1.50dB
-1.45dB
-1.40dB
-1.35dB
-1.30dB
-1.25dB
-1.20dB
-1.15dB
-1.10dB
-1.05dB
-1.00dB
-0.95dB
-0.90dB
-0.85dB
-0.80dB
-0.75dB
-0.70dB
-0.65dB
-0.60dB
-0.55dB
-0.50dB
-0.45dB
-0.40dB
-0.35dB
-0.30dB
-0.25dB
-0.20dB
-0.15dB
-0.10dB
-0.05dB
0.00dB
21
A Fader Table of -∞ to 10 dB
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Data
Value
-InfdB
64
-138.00dB
65
-135.00dB
66
-132.00dB
67
-129.00dB
68
-126.00dB
69
-123.00dB
70
-120.00dB
71
-117.00dB
72
-114.00dB
73
-111.00dB
74
-108.00dB
75
-105.00dB
76
-102.00dB
77
-99.00dB
78
-96.00dB
79
-95.00dB
80
-94.00dB
81
-93.00dB
82
-92.00dB
83
-91.00dB
84
-90.00dB
85
-89.00dB
86
-88.00dB
87
-87.00dB
88
-86.00dB
89
-85.00dB
90
-84.00dB
91
-83.00dB
92
-82.00dB
93
-81.00dB
94
-80.00dB
95
-79.00dB
96
-78.00dB
97
-77.80dB
98
-77.60dB
99
-77.40dB
100
-77.20dB
101
-77.00dB
102
-76.80dB
103
-76.60dB
104
-76.40dB
105
-76.20dB
106
-76.00dB
107
-75.80dB
108
-75.60dB
109
-75.40dB
110
-75.20dB
111
-75.00dB
112
-74.80dB
113
-74.60dB
114
-74.40dB
115
-74.20dB
116
-74.00dB
117
-73.80dB
118
-73.60dB
119
-73.40dB
120
-73.20dB
121
-73.00dB
122
-72.80dB
123
-72.60dB
124
-72.40dB
125
-72.20dB
126
-72.00dB
127
Data
-71.80dB
-71.60dB
-71.40dB
-71.20dB
-71.00dB
-70.80dB
-70.60dB
-70.40dB
-70.20dB
-70.00dB
-69.80dB
-69.60dB
-69.40dB
-69.20dB
-69.00dB
-68.80dB
-68.60dB
-68.40dB
-68.20dB
-68.00dB
-67.80dB
-67.60dB
-67.40dB
-67.20dB
-67.00dB
-66.80dB
-66.60dB
-66.40dB
-66.20dB
-66.00dB
-65.80dB
-65.60dB
-65.40dB
-65.20dB
-65.00dB
-64.80dB
-64.60dB
-64.40dB
-64.20dB
-64.00dB
-63.80dB
-63.60dB
-63.40dB
-63.20dB
-63.00dB
-62.80dB
-62.60dB
-62.40dB
-62.20dB
-62.00dB
-61.80dB
-61.60dB
-61.40dB
-61.20dB
-61.00dB
-60.80dB
-60.60dB
-60.40dB
-60.20dB
-60.00dB
-59.80dB
-59.60dB
-59.40dB
-59.20dB
Value
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Data
-59.00dB
-58.80dB
-58.60dB
-58.40dB
-58.20dB
-58.00dB
-57.80dB
-57.60dB
-57.40dB
-57.20dB
-57.00dB
-56.80dB
-56.60dB
-56.40dB
-56.20dB
-56.00dB
-55.80dB
-55.60dB
-55.40dB
-55.20dB
-55.00dB
-54.80dB
-54.60dB
-54.40dB
-54.20dB
-54.00dB
-53.80dB
-53.60dB
-53.40dB
-53.20dB
-53.00dB
-52.80dB
-52.60dB
-52.40dB
-52.20dB
-52.00dB
-51.80dB
-51.60dB
-51.40dB
-51.20dB
-51.00dB
-50.80dB
-50.60dB
-50.40dB
-50.20dB
-50.00dB
-49.80dB
-49.60dB
-49.40dB
-49.20dB
-49.00dB
-48.80dB
-48.60dB
-48.40dB
-48.20dB
-48.00dB
-47.80dB
-47.60dB
-47.40dB
-47.20dB
-47.00dB
-46.80dB
-46.60dB
-46.40dB
Value
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
Data
-46.20dB
-46.00dB
-45.80dB
-45.60dB
-45.40dB
-45.20dB
-45.00dB
-44.80dB
-44.60dB
-44.40dB
-44.20dB
-44.00dB
-43.80dB
-43.60dB
-43.40dB
-43.20dB
-43.00dB
-42.80dB
-42.60dB
-42.40dB
-42.20dB
-42.00dB
-41.80dB
-41.60dB
-41.40dB
-41.20dB
-41.00dB
-40.80dB
-40.60dB
-40.40dB
-40.20dB
-40.00dB
-39.90dB
-39.80dB
-39.70dB
-39.60dB
-39.50dB
-39.40dB
-39.30dB
-39.20dB
-39.10dB
-39.00dB
-38.90dB
-38.80dB
-38.70dB
-38.60dB
-38.50dB
-38.40dB
-38.30dB
-38.20dB
-38.10dB
-38.00dB
-37.90dB
-37.80dB
-37.70dB
-37.60dB
-37.50dB
-37.40dB
-37.30dB
-37.20dB
-37.10dB
-37.00dB
-36.90dB
-36.80dB
Value
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
Data
-36.70dB
-36.60dB
-36.50dB
-36.40dB
-36.30dB
-36.20dB
-36.10dB
-36.00dB
-35.90dB
-35.80dB
-35.70dB
-35.60dB
-35.50dB
-35.40dB
-35.30dB
-35.20dB
-35.10dB
-35.00dB
-34.90dB
-34.80dB
-34.70dB
-34.60dB
-34.50dB
-34.40dB
-34.30dB
-34.20dB
-34.10dB
-34.00dB
-33.90dB
-33.80dB
-33.70dB
-33.60dB
-33.50dB
-33.40dB
-33.30dB
-33.20dB
-33.10dB
-33.00dB
-32.90dB
-32.80dB
-32.70dB
-32.60dB
-32.50dB
-32.40dB
-32.30dB
-32.20dB
-32.10dB
-32.00dB
-31.90dB
-31.80dB
-31.70dB
-31.60dB
-31.50dB
-31.40dB
-31.30dB
-31.20dB
-31.10dB
-31.00dB
-30.90dB
-30.80dB
-30.70dB
-30.60dB
-30.50dB
-30.40dB
Value
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
Data
-30.30dB
-30.20dB
-30.10dB
-30.00dB
-29.90dB
-29.80dB
-29.70dB
-29.60dB
-29.50dB
-29.40dB
-29.30dB
-29.20dB
-29.10dB
-29.00dB
-28.90dB
-28.80dB
-28.70dB
-28.60dB
-28.50dB
-28.40dB
-28.30dB
-28.20dB
-28.10dB
-28.00dB
-27.90dB
-27.80dB
-27.70dB
-27.60dB
-27.50dB
-27.40dB
-27.30dB
-27.20dB
-27.10dB
-27.00dB
-26.90dB
-26.80dB
-26.70dB
-26.60dB
-26.50dB
-26.40dB
-26.30dB
-26.20dB
-26.10dB
-26.00dB
-25.90dB
-25.80dB
-25.70dB
-25.60dB
-25.50dB
-25.40dB
-25.30dB
-25.20dB
-25.10dB
-25.00dB
-24.90dB
-24.80dB
-24.70dB
-24.60dB
-24.50dB
-24.40dB
-24.30dB
-24.20dB
-24.10dB
-24.00dB
DME Remote Control Protocol Specifications V3.1
Value
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
Data
-23.90dB
-23.80dB
-23.70dB
-23.60dB
-23.50dB
-23.40dB
-23.30dB
-23.20dB
-23.10dB
-23.00dB
-22.90dB
-22.80dB
-22.70dB
-22.60dB
-22.50dB
-22.40dB
-22.30dB
-22.20dB
-22.10dB
-22.00dB
-21.90dB
-21.80dB
-21.70dB
-21.60dB
-21.50dB
-21.40dB
-21.30dB
-21.20dB
-21.10dB
-21.00dB
-20.90dB
-20.80dB
-20.70dB
-20.60dB
-20.50dB
-20.40dB
-20.30dB
-20.20dB
-20.10dB
-20.00dB
-19.95dB
-19.90dB
-19.85dB
-19.80dB
-19.75dB
-19.70dB
-19.65dB
-19.60dB
-19.55dB
-19.50dB
-19.45dB
-19.40dB
-19.35dB
-19.30dB
-19.25dB
-19.20dB
-19.15dB
-19.10dB
-19.05dB
-19.00dB
-18.95dB
-18.90dB
-18.85dB
-18.80dB
Value
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
Data
-18.75dB
-18.70dB
-18.65dB
-18.60dB
-18.55dB
-18.50dB
-18.45dB
-18.40dB
-18.35dB
-18.30dB
-18.25dB
-18.20dB
-18.15dB
-18.10dB
-18.05dB
-18.00dB
-17.95dB
-17.90dB
-17.85dB
-17.80dB
-17.75dB
-17.70dB
-17.65dB
-17.60dB
-17.55dB
-17.50dB
-17.45dB
-17.40dB
-17.35dB
-17.30dB
-17.25dB
-17.20dB
-17.15dB
-17.10dB
-17.05dB
-17.00dB
-16.95dB
-16.90dB
-16.85dB
-16.80dB
-16.75dB
-16.70dB
-16.65dB
-16.60dB
-16.55dB
-16.50dB
-16.45dB
-16.40dB
-16.35dB
-16.30dB
-16.25dB
-16.20dB
-16.15dB
-16.10dB
-16.05dB
-16.00dB
-15.95dB
-15.90dB
-15.85dB
-15.80dB
-15.75dB
-15.70dB
-15.65dB
-15.60dB
22
Value
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
Data
-15.55dB
-15.50dB
-15.45dB
-15.40dB
-15.35dB
-15.30dB
-15.25dB
-15.20dB
-15.15dB
-15.10dB
-15.05dB
-15.00dB
-14.95dB
-14.90dB
-14.85dB
-14.80dB
-14.75dB
-14.70dB
-14.65dB
-14.60dB
-14.55dB
-14.50dB
-14.45dB
-14.40dB
-14.35dB
-14.30dB
-14.25dB
-14.20dB
-14.15dB
-14.10dB
-14.05dB
-14.00dB
-13.95dB
-13.90dB
-13.85dB
-13.80dB
-13.75dB
-13.70dB
-13.65dB
-13.60dB
-13.55dB
-13.50dB
-13.45dB
-13.40dB
-13.35dB
-13.30dB
-13.25dB
-13.20dB
-13.15dB
-13.10dB
-13.05dB
-13.00dB
-12.95dB
-12.90dB
-12.85dB
-12.80dB
-12.75dB
-12.70dB
-12.65dB
-12.60dB
-12.55dB
-12.50dB
-12.45dB
-12.40dB
Value
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
Data
-12.35dB
-12.30dB
-12.25dB
-12.20dB
-12.15dB
-12.10dB
-12.05dB
-12.00dB
-11.95dB
-11.90dB
-11.85dB
-11.80dB
-11.75dB
-11.70dB
-11.65dB
-11.60dB
-11.55dB
-11.50dB
-11.45dB
-11.40dB
-11.35dB
-11.30dB
-11.25dB
-11.20dB
-11.15dB
-11.10dB
-11.05dB
-11.00dB
-10.95dB
-10.90dB
-10.85dB
-10.80dB
-10.75dB
-10.70dB
-10.65dB
-10.60dB
-10.55dB
-10.50dB
-10.45dB
-10.40dB
-10.35dB
-10.30dB
-10.25dB
-10.20dB
-10.15dB
-10.10dB
-10.05dB
-10.00dB
-9.95dB
-9.90dB
-9.85dB
-9.80dB
-9.75dB
-9.70dB
-9.65dB
-9.60dB
-9.55dB
-9.50dB
-9.45dB
-9.40dB
-9.35dB
-9.30dB
-9.25dB
-9.20dB
Value
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
Data
-9.15dB
-9.10dB
-9.05dB
-9.00dB
-8.95dB
-8.90dB
-8.85dB
-8.80dB
-8.75dB
-8.70dB
-8.65dB
-8.60dB
-8.55dB
-8.50dB
-8.45dB
-8.40dB
-8.35dB
-8.30dB
-8.25dB
-8.20dB
-8.15dB
-8.10dB
-8.05dB
-8.00dB
-7.95dB
-7.90dB
-7.85dB
-7.80dB
-7.75dB
-7.70dB
-7.65dB
-7.60dB
-7.55dB
-7.50dB
-7.45dB
-7.40dB
-7.35dB
-7.30dB
-7.25dB
-7.20dB
-7.15dB
-7.10dB
-7.05dB
-7.00dB
-6.95dB
-6.90dB
-6.85dB
-6.80dB
-6.75dB
-6.70dB
-6.65dB
-6.60dB
-6.55dB
-6.50dB
-6.45dB
-6.40dB
-6.35dB
-6.30dB
-6.25dB
-6.20dB
-6.15dB
-6.10dB
-6.05dB
-6.00dB
Value
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
Data
-5.95dB
-5.90dB
-5.85dB
-5.80dB
-5.75dB
-5.70dB
-5.65dB
-5.60dB
-5.55dB
-5.50dB
-5.45dB
-5.40dB
-5.35dB
-5.30dB
-5.25dB
-5.20dB
-5.15dB
-5.10dB
-5.05dB
-5.00dB
-4.95dB
-4.90dB
-4.85dB
-4.80dB
-4.75dB
-4.70dB
-4.65dB
-4.60dB
-4.55dB
-4.50dB
-4.45dB
-4.40dB
-4.35dB
-4.30dB
-4.25dB
-4.20dB
-4.15dB
-4.10dB
-4.05dB
-4.00dB
-3.95dB
-3.90dB
-3.85dB
-3.80dB
-3.75dB
-3.70dB
-3.65dB
-3.60dB
-3.55dB
-3.50dB
-3.45dB
-3.40dB
-3.35dB
-3.30dB
-3.25dB
-3.20dB
-3.15dB
-3.10dB
-3.05dB
-3.00dB
-2.95dB
-2.90dB
-2.85dB
-2.80dB
Value
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
Data
-2.75dB
-2.70dB
-2.65dB
-2.60dB
-2.55dB
-2.50dB
-2.45dB
-2.40dB
-2.35dB
-2.30dB
-2.25dB
-2.20dB
-2.15dB
-2.10dB
-2.05dB
-2.00dB
-1.95dB
-1.90dB
-1.85dB
-1.80dB
-1.75dB
-1.70dB
-1.65dB
-1.60dB
-1.55dB
-1.50dB
-1.45dB
-1.40dB
-1.35dB
-1.30dB
-1.25dB
-1.20dB
-1.15dB
-1.10dB
-1.05dB
-1.00dB
-0.95dB
-0.90dB
-0.85dB
-0.80dB
-0.75dB
-0.70dB
-0.65dB
-0.60dB
-0.55dB
-0.50dB
-0.45dB
-0.40dB
-0.35dB
-0.30dB
-0.25dB
-0.20dB
-0.15dB
-0.10dB
-0.05dB
0.00dB
0.05dB
0.10dB
0.15dB
0.20dB
0.25dB
0.30dB
0.35dB
0.40dB
Value
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
Data
0.45dB
0.50dB
0.55dB
0.60dB
0.65dB
0.70dB
0.75dB
0.80dB
0.85dB
0.90dB
0.95dB
1.00dB
1.05dB
1.10dB
1.15dB
1.20dB
1.25dB
1.30dB
1.35dB
1.40dB
1.45dB
1.50dB
1.55dB
1.60dB
1.65dB
1.70dB
1.75dB
1.80dB
1.85dB
1.90dB
1.95dB
2.00dB
2.05dB
2.10dB
2.15dB
2.20dB
2.25dB
2.30dB
2.35dB
2.40dB
2.45dB
2.50dB
2.55dB
2.60dB
2.65dB
2.70dB
2.75dB
2.80dB
2.85dB
2.90dB
2.95dB
3.00dB
3.05dB
3.10dB
3.15dB
3.20dB
3.25dB
3.30dB
3.35dB
3.40dB
3.45dB
3.50dB
3.55dB
3.60dB
Value
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
Data
3.65dB
3.70dB
3.75dB
3.80dB
3.85dB
3.90dB
3.95dB
4.00dB
4.05dB
4.10dB
4.15dB
4.20dB
4.25dB
4.30dB
4.35dB
4.40dB
4.45dB
4.50dB
4.55dB
4.60dB
4.65dB
4.70dB
4.75dB
4.80dB
4.85dB
4.90dB
4.95dB
5.00dB
5.05dB
5.10dB
5.15dB
5.20dB
5.25dB
5.30dB
5.35dB
5.40dB
5.45dB
5.50dB
5.55dB
5.60dB
5.65dB
5.70dB
5.75dB
5.80dB
5.85dB
5.90dB
5.95dB
6.00dB
6.05dB
6.10dB
6.15dB
6.20dB
6.25dB
6.30dB
6.35dB
6.40dB
6.45dB
6.50dB
6.55dB
6.60dB
6.65dB
6.70dB
6.75dB
6.80dB
Value
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
Data
6.85dB
6.90dB
6.95dB
7.00dB
7.05dB
7.10dB
7.15dB
7.20dB
7.25dB
7.30dB
7.35dB
7.40dB
7.45dB
7.50dB
7.55dB
7.60dB
7.65dB
7.70dB
7.75dB
7.80dB
7.85dB
7.90dB
7.95dB
8.00dB
8.05dB
8.10dB
8.15dB
8.20dB
8.25dB
8.30dB
8.35dB
8.40dB
8.45dB
8.50dB
8.55dB
8.60dB
8.65dB
8.70dB
8.75dB
8.80dB
8.85dB
8.90dB
8.95dB
9.00dB
9.05dB
9.10dB
9.15dB
9.20dB
9.25dB
9.30dB
9.35dB
9.40dB
9.45dB
9.50dB
9.55dB
9.60dB
9.65dB
9.70dB
9.75dB
9.80dB
9.85dB
9.90dB
9.95dB
10.00dB
© 2005-2009 Yamaha Corporation
DME Remote Control Protocol Specifications V3.1
23
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : Yes
Encryption : Standard V2.3 (128-bit)
User Access : Print, Copy, Extract, Print high-res
Page Mode : UseOutlines
XMP Toolkit : 3.1-702
About : uuid:e8d590bb-5d00-46a7-9265-3035b5b3daef
Producer : Acrobat Distiller 6.0.1 (Windows)
Creator Tool : Excel 用 Acrobat PDFMaker 6.0
Modify Date : 2010:11:15 18:07:57+09:00
Create Date : 2009:01:21 15:49:00+09:00
Metadata Date : 2010:11:15 18:07:57+09:00
Document ID : uuid:fe2ca75c-531a-4fe9-a907-12e3bb7a1fa2
Instance ID : uuid:99353144-054f-45fe-9419-631dbc95a5b4
Format : application/pdf
Title : DME Remote Control Protocol Specifications
Creator : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
Description : DME_RemoteCtrlProtocolSpecs_v310_2_en.pdf
Page Count : 23
Subject : DME_RemoteCtrlProtocolSpecs_v310_2_en.pdf
Author : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
EXIF Metadata provided by EXIF.tools
.