Yamaha RX A2000 Owner's Manual (for USA) Omrc En1 1
User Manual: Yamaha RX-A2000 Owner's Manual (for USA)
Open the PDF directly: View PDF .Page Count: 179
Owner’s Manual
AV Receiver
English for U.S.A.
BEFORE USE
SOURCE RECEIVER
About this manual
AV
1
2
3
4
5
6
1
2
7
3
V-AUX
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
• Some features are not available in certain regions.
• This manual is created prior to production. Design and
specifications are subject to change in part as a result
of improvements, etc. In case of differences between
the manual and product, the product has priority.
• “hON SCREEN” (example) indicates the name of
the parts on the remote control. Refer to the “Remote
control” (☞p. 12) for the information about each
position of the parts.
• J1 indicates that the reference is in the footnote.
Refer to the corresponding numbers on the bottom of
the page.
• ☞ indicates the page describing the related
information.
• Click on the “
” at the bottom of the page to
display the corresponding page in “Part names and
functions.”
Front panel
Rear panel
Front panel display
Remote control
AUDIO
h
ON SCREEN
ENTER
i
Language selection
This procedure allows you to select the language of
menus and messages on the TV screen.
1
4
Press iCursor B / C to select the favorite
language from the following options.
Press hON SCREEN to display the ON
SCREEN menu.
English (English),
(Japanese),
(French),
(German),
(Spanish),
(Russian)
2
Press iCursor B / C to select “Setup” and
press iENTER.
3
Press iCursor D / E to select the
“Language” and press iENTER.
5
Press hON SCREEN to close the ON
SCREEN menu.
Supplied accessories
Check that you received all of the following parts.
•
•
•
•
•
•
•
Remote control
Simplified remote control
Batteries (AAA, R03, UM-4) x 4
Power cable
YPAO microphone
AM loop antenna
Indoor FM antenna
En
2
CONTENTS
INTRODUCTION
Features and capabilities ................................................... 5
Connecting audio/video recording devices .................... 38
Connecting to the network ............................................. 38
Connecting a USB storage device .................................. 39
Using the TV OSD to operate the unit ............................. 6
Basic OSD menu operations............................................. 6
Viewing or modifying content for the current input source
........................................................... 6
Configuring settings for this unit
...................................................... 6
Adjust settings for each input source ..... 7
Connecting the FM/AM antennas .................................. 40
Part names and functions.................................................. 8
Front panel........................................................................ 8
Front panel with the cover opened ................................... 9
Rear panel....................................................................... 10
Front panel display ......................................................... 11
Remote control ............................................................... 12
Remote control with the cover open............................... 13
On-screen display ........................................................... 14
Changing input settings with a single key
(SCENE function) ............................................................ 50
Selecting a SCENE suited to an external component .... 50
CONNECTIONS
Connecting speakers ........................................................ 15
Speaker channels and functions...................................... 15
Speaker layout ................................................................ 16
Connecting speakers and subwoofers............................. 20
Advanced speaker configuration .................................... 24
Speaker layout utilizing an external power amplifier..... 24
Connecting an external amplifier ................................... 26
Connecting external components.................................... 27
Jacks and cables.............................................................. 27
Connecting a TV monitor............................................... 28
Connecting BD/DVD players and other devices ............ 31
Connecting game consoles or video camcorders............ 36
Connecting a multi-format player
or an external decoder .................................................... 36
Connecting a SCENE link
playback-compatible device ........................................... 37
Using the Trigger function to link
external component power.............................................. 37
Setting up the speaker parameters automatically
(YPAO).............................................................................. 41
PLAYBACK
Basic playback procedure ............................................... 48
Enjoying favorite sound field effect ............................... 51
Selecting sound programs and sound decoders.............. 51
Enjoying surround sound
with the CINEMA DSP function ................................... 51
Enjoying unprocessed playback
(Straight decoding mode) ............................................... 52
Enjoying Hi-Fi Sound Quality (Pure Direct Mode) ....... 53
Enjoying stereo playback ............................................... 53
Enjoying compressed music source with better sound
quality (Compressed Music Enhancer) .......................... 53
Sound programs.............................................................. 54
Using the TV display to control this unit....................... 56
Basic operations via the TV screen display ................... 56
Configuring settings specific to an individual input
source (Option menu) ...................................................... 58
Option menu display and setup ...................................... 58
Option menu................................................................... 59
Confirming and operating input sources
from the content window................................................. 62
Displaying the content window on the TV screen ......... 62
Switching the display between the Now Playing view
and the Browse view ...................................................... 62
Navigating the FM/AM tuner
from the content window ............................................... 64
Listening to the HD Radio™ .......................................... 66
Selecting HD Radio™ audio programs ......................... 66
Using the iTunes Tagging .............................................. 67
Displaying the HD Radio™ information ....................... 67
Navigating the HD Radio™ tuner
from the content window ............................................... 68
Listening to the SIRIUS Satellite Radio™ .................... 70
Connecting the SiriusConnect™ tuner .......................... 70
Activating SIRIUS Satellite Radio™ subscription ........ 71
SIRIUS Satellite Radio™ operations............................. 71
Registering and recalling the SIRIUS Satellite Radio™
channels.......................................................................... 72
Displaying the SIRIUS Satellite Radio™ information .. 73
Navigating the SIRIUS Satellite Radio™ tuner
from the content window ............................................... 74
Playing back tunes on the PC......................................... 76
Windows Media Player setup......................................... 76
Playback of PC music contents...................................... 76
Playing back tunes on the USB storage devices............ 78
Playback of the USB storage device .............................. 78
Listening to the Internet Radio ...................................... 80
Listening to Internet Radio ............................................ 80
Using the Rhapsody® service.......................................... 82
Rhapsody® account sign-in............................................ 82
Playback of Rhapsody® contents................................... 83
Listening to the SIRIUS Internet Radio........................ 86
SIRIUS Internet Radio account sign-in ......................... 86
Navigating the Sirius Internet Radio menu.................... 87
Using shortcut function................................................... 89
FM/AM tuning ................................................................. 63
Selecting a frequency for reception (Normal tuning)..... 63
En
3
Playing back tunes from your iPod™/iPhone™ ........... 90
Connecting the Universal Dock for iPod........................ 90
Controlling an iPod™/iPhone™ .................................... 90
Playing iPod™/iPhone™ from the menu screen
(Menu browse control) ................................................... 91
Operating basic playback functions
via the remote control (Simple remote control) ............. 92
Playing iPod™/iPhone™ with wireless connection....... 92
Playing back tunes from Bluetooth™ components....... 94
Connecting a Yamaha Bluetooth
Wireless Audio Receiver ................................................ 94
Pairing Bluetooth™ components.................................... 94
Using Bluetooth™ components ..................................... 95
Controlling this unit by using the Web browser
(Web Control Center) ...................................................... 96
Displaying and Operating Web Control Center.............. 96
SETUP
Configuring input sources (Input menu) ....................... 98
Configuring input sources .............................................. 98
Input menu...................................................................... 99
Editing the SCENE function (Scene menu) ................. 102
Editing a scene.............................................................. 102
Scene menu................................................................... 103
Simple registering as the SCENE................................. 104
Setting sound program parameters
(Sound Program menu) ................................................. 105
Editing sound programs................................................ 105
CINEMA DSP parameters ........................................... 106
Parameters usable in certain sound programs .............. 108
Parameters usable in surround decoder ........................ 109
Setting various functions (Setup menu) ....................... 110
Operating the Setup menu ............................................ 110
Setup menu ................................................................... 111
Manages settings for speakers ...................................... 111
Setting the audio output function of this unit ............... 115
Setting this unit’s video output function....................... 117
Setting HDMI functions ............................................... 118
Adjusting this unit’s network parameters..................... 121
Setting this unit’s multi-zone function ......................... 122
Making the receiver easier to use ................................. 123
Language ...................................................................... 126
Confirming information of this unit
(Information menu) ....................................................... 127
Selecting information ................................................... 127
Controlling the remote control to operate various
functions ......................................................................... 129
Keys connecting external components ......................... 129
Customizing the remote control ................................... 130
Setting remote control codes ........................................ 130
Programming from other remote controls.................... 132
Changing source names in the display window ........... 134
Macro programming features ....................................... 135
Clearing configurations ................................................ 136
Simplified remote control............................................. 138
Extended functionality that can be configured
as needed (Advanced Setup menu)............................... 139
Displaying/Setting the Advanced Setup menu............. 139
Setting the impedance of speakers .............................. 139
Remote sensor .............................................................. 139
Avoiding crossing remote control signals
when using multiple Yamaha receivers ........................ 140
Resetting the SIRIUS Satellite Radio™
parental lock code......................................................... 140
Changing TV format .................................................... 140
Removing HDMI video output up-scaling limits......... 141
Recovery and backup of the system settings................ 141
Initializing various settings for this unit....................... 141
Firmware update........................................................... 142
Firmware version.......................................................... 142
APPENDIX
Troubleshooting ............................................................. 150
General ......................................................................... 150
HDMI™ ....................................................................... 152
Tuner (FM/AM) ........................................................... 153
HD Radio™ Reception ................................................ 153
iTunes Tagging............................................................. 154
SIRIUS Satellite Radio™ ............................................ 154
USB and Network ........................................................ 155
iPod™/iPhone™ .......................................................... 157
Bluetooth™ .................................................................. 157
Remote control............................................................. 158
Glossary .......................................................................... 159
Audio information........................................................ 159
Sound program information ......................................... 160
Video information ........................................................ 161
Compatibility of the input and output video signals .... 161
Information on HDMI™............................................... 162
About trademarks ......................................................... 163
Specifications.................................................................. 164
Index ............................................................................... 166
Using the HDMI Control function ............................... 143
Enjoying the contents in another room ....................... 147
Connecting Zone2 or Zone3......................................... 147
Controlling Zone2 or Zone3......................................... 149
Enjoying the music in all rooms................................... 149
En
4
INTRODUCTION
Features and capabilities
■ Built-in high-quality, high-power 7-channel amplifier
■ Playback of music on the USB storage devices ................................................... 78
■ Multi-channel speaker configuration capability
■ Sophisticated on-screen display (OSD) for easy operation
–
–
–
–
–
2- to 7.1-channel speaker configurations .................................................................................................16
Presence speaker connections for playback with a richer sound field effect...........................................15
Bi-amplification connections for high-quality playback .........................................................................21
External amplifier connections for high-quality playback and expansion of channels ...........................24
Speaker impedance configuration............................................................................................................21
■ HDMI compatibility
– 8 HDMI input jacks (7 on the rear, 1 on the front) supporting 3D video signal input ............................31
– 2 selectable HDMI output jacks supporting Audio Return Channel and 3D video signal ......................29
■ Automatic setup for speaker acoustic parameters
(YPAO - Yamaha Parametric Room Acoustic Optimizer) ......................................41
■ Extensive inputs (max. 13) for external playback components
–
–
–
–
–
–
BD/DVD/CD player connection ..............................................................................................................31
Game console / video camcorder connection ..........................................................................................36
Multi-format player / external decoder connection .................................................................................36
iPod/iPhone wired connection .................................................................................................................90
iPod/iPhone wireless connection .............................................................................................................92
Bluetooth component connection ............................................................................................................94
–
–
–
–
Selection of input sources, scenes, and sound programs .........................................................................56
Navigation for the current input source (content window) ......................................................................62
Setup for this unit (ON SCREEN menu) .................................................................................................98
Setup for each input source (Option menu) .............................................................................................58
Most of functions can be operated with on-screen display on the TV screen. Refer to “Using the TV
OSD to operate the unit” on the following pages for information on functions that can be controlled
using the on-screen display.
■ Customizable remote control
– Remote control code setup for operation of external components ........................................................130
– Learning function from other remote controls.......................................................................................132
– Programming macro for a series of operations......................................................................................135
■ Multi-room listening capability (Zone2/Zone3) ................................................... 147
■ 1-button input/sound program/setting switching (SCENE function) ...................50
■ Built-in sound programs and surround decoders for playback variety of sources
–
–
–
–
Spatial sound playback with sound field effects (CINEMA DSP) ..........................................................51
Playback with no sound field effects (straight decoding) ........................................................................52
High-fidelity sound playback (Pure Direct).............................................................................................53
Enhanced sound playback for compressed sources (Compressed Music Enhancer)...............................53
■ Tuner playback
– FM/AM broadcast....................................................................................................................................63
– HD Radio™ digital broadcast..................................................................................................................66
– SIRIUS Satellite Radio™ broadcast........................................................................................................70
■ Playback and control via network
– Playback of music on the PC and DLNA server......................................................................................76
– Internet radio service playback ................................................................................................................80
– Control this unit via network (Web Browser Control).............................................................................96
En
5
INTRODUCTION
Using the TV OSD to operate the unit
This unit features a sophisticated on-screen display (OSD) for the TV screen. The OSD is designed to enable visual guidance that simplifies operations. The OSD mainly displays the ON SCREEN and
Option menus, as well as the content window that displays the content of current input sources.
Basic OSD menu operations
Configuring settings for this unit
■ Select an input source, scene and sound program
■ Configure an input source
– Select an input source ..............................................................................................................................56
– Select a scene ...........................................................................................................................................56
– Select a sound program............................................................................................................................57
■ Select a language
– Change the language displayed on the TV screen ............................................................126
Viewing or modifying content for the current input source
■ Operate the FM/AM tuner, HD Radio or SIRIUS Satellite Radio
– Display preset stations/channels for selection .............................................................................64, 68, 74
– Display information on the station/channel currently received ...................................................64, 68, 74
– Perform operations such as searching for and registering stations/channels
using the screen button.................................................................................................................64, 68, 74
■ Operate the Internet radio, Rhapsody or SIRIUS Internet Radio
–
–
–
–
–
Account setup for Rhapsody or SIRIUS Internet Radio....................................................................82, 86
Display information on the station/channel currently received ...................................................80, 83, 87
Play back radio contents ..............................................................................................................80, 83, 87
Bookmark Internet radio stations.............................................................................................................80
Add Rhapsody items to “My Library”.....................................................................................................85
■ Operate the iPod music sources
– Display the list of iPod music sources for selection ................................................................................91
– Perform operations such as play, stop and pause using the TV screen ............91
–
–
–
–
–
–
–
–
Change the input source name ...........................................................................99
Specify a format for digital audio signals ................................................................100
Enhance the sound of compressed audio ..........................................................................100
Output a video signal input from another input source
while playing a multi-channel audio signal .....................................................................101
Charge the iPod/iPhone when this unit is in standby mode ....................................100
Limit access to specific SIRIUS Satellite channels .....................................................74
Play music sources on a PC using external controls ..................................................100
Register your Rhapsody or SIRIUS Internet Radio account
..........................................................................................82, 86
■ Customize a scene
– Register or clear settings for a selected scene , , ....................................103, 104
– Turn on a Yamaha BD/DVD player or CD player connected to this unit automatically
when a scene is selected .................................................................................................103
– Changing a scene name and icon .....................................................................104
■ Adjust a sound program (sound program)
– Adjust sound program parameters .........................................................................................................105
■ Display settings information for this unit
–
–
–
–
–
–
Display audio signal information ................................................................................127
Display video signal information ................................................................................127
Display HDMI signal information ...........................................................................127
Display network information ..............................................................................................128
Display system information ..................................................................................................128
Display Zone information ........................................................................................................128
Continues to the
next page
En
6
INTRODUCTION
Using the TV OSD to operate the unit
■ Adjust acoustic parameters to match your speakers and listening environment
– Specify speaker acoustic parameters automatically
(Yamaha Parametric Room Acoustic Optimizer - YPAO).......................................................................41
– Set up this unit’s speaker configuration simply ................................................112
– Specify settings for each speaker ...............................................................................112
– Control volume control for each speaker ................................................................................114
– Apply speaker distance settings .........................................................................................114
– Control equalizer sound quality ................................................................................114
– Adjust test tone speaker ....................................................................................................115
■ Adjust audio signals output from this unit
–
–
–
–
–
–
Correct lag between audio and video signals ......................................................................115
Select a dynamic range adjustment method ...........................................................116
Specify the maximum volume .....................................................................................116
Specify the initial volume ..........................................................................................116
Restrict video signal in Pure Direct Mode ...........................................................116
Adjust DSP effect and volume level ................................................................116
■ Adjust video signals output from this unit
– Convert analog video signal to another type of signal .....................117
– Specify the resolution and aspect ratio of video signals and adjust video quality ..........117
■ HDMI settings
–
–
–
–
Assign the audio input source for the TV ...............................................................119
Listen to TV audio with HDMI cable connection ............................119
Transmit HDMI audio/video to the TV during standby mode .............................120
Change the output destination of HDMI input audio signals .....................................120
■ Specify other functions for this unit
–
–
–
–
–
Enter standby mode automatically when no operations are performed .............124
Assign jacks to the selected input source .................................................................125
Change the wall paper displayed on the TV screen ........................................................125
Specify the function of the TRIGGER OUT jack for controlling external components
......................................................................................................125
– Prohibit changes to settings .....................................................................................126
Adjust settings for each input source
–
–
–
–
–
–
–
–
–
–
–
Adjust bass and treble levels .........................................................................................60
Enable low-volume background music ......................................................................60
Enjoying more spatial sound fields ............................................................60
Adjust the vertical position of dialogues ......................................................................60
Select the 5.1-channel signal playback method ..................................................60
Adjust the volume of input sources ...............................................................................61
Selecting a video adjustment preset ......................................................................61
Selecting audio input jacks ............................................................................................61
Shuffle or repeat playback ..........................................................................................61
Connect / Disconnect Bluetooth component to this unit ...................................61
Pairing Bluetooth component with this unit ...........................................................................61
■ Network settings
– Specify this unit’s IP address ..........................................................................................121
– Accept the commands over a LAN network when this unit is in the standby mode
...............................................................................................................................121
– Specify the mac address filter for this unit ......................................................121
■ Enable listening in multiple rooms (multi-zone function)
– Adjust Zone2/Zone3 volume ..........................................................................122
– Display the Zone2/Zone3 menu on the TV ......................................................122
– Rename zones or scenes .....................123
En
7
INTRODUCTION
Part names and functions
c Front panel display
Front panel
Displays information on this unit (☞p. 11).
d PURE DIRECT
a MAIN ZONE A (Power)
e
Switches this unit between on and standby mode.
b HDMI Through/iPod Charge indicator
Lights up in any of the following cases while the unit is in standby mode.
• When the Standby Through function is enabled and audio/video from
an external component connected with HDMI is output to a TV
during standby mode (☞p. 120).
• When an iPod/iPhone, which is placed in the Universal Dock for iPod,
is charging while the unit is in standby mode (☞p. 100).
This indicator also lights up when the Yamaha Wireless System for
iPod is connected to this unit (☞p. 92).
a
e
b
f
Switches this unit to Pure Direct Mode (☞p. 53).
INPUT selector
Selects an input source from which to playback. Rotate this selector to
cycle through the input sources in order.
VOLUME
Adjusts the volume level.
c
■ Opening and closing the front panel door
To use controls or jacks behind the front panel door, gently press
the bottom of the door to open it. Keep the door closed when not
using controls or jacks behind the front panel door.
d
f
Continues to the
next page
En
8
INTRODUCTION
Part names and functions
Front panel with the cover opened
m MULTI ZONE
g ON SCREEN
Turns on and off the ON SCREEN menu.
h OPTION
Turns on and off the Option menu (☞p. 58).
i TONE/BALANCE
j
k
l
Adjusts high-frequency/low-frequency output of speakers/headphones
in each zone (☞p. 49, p. 149).
Adjusts the balance of the volume of the left and right channels in
Zone2 or Zone3 (☞p. 149).
STRAIGHT
Changes a sound program to straight decoding mode (☞p. 52).
PROGRAM l / h
Selects a sound program (☞p. 51). Press the left or right key repeatedly
to cycle through sound programs.
SCENE
Switches the input source, the sound program, and the HDMI OUT with
a single button (☞p. 50, p. 102). When this unit is in standby mode,
press this key to switch on.
n
o
p
q
r Cursor B / C / D / E, ENTER, RETURN
ZONE2
Switches to enable/disable the audio and video output to Zone2
(☞p. 122, p. 147).
ZONE3
Switches to enable/disable the audio and video output to Zone3
(☞p. 122, p. 148).
ZONE CONTROLS
Switches to Zone2 or Zone3 operation mode. This unit, or its remote
control, can be used to select input sources or adjust volume for an
external amplifier in another room or the built-in amplifier for speakers
in another room (☞p. 149).
INFO
Changes the information displayed on the front panel display (☞p. 11).
MEMORY
Registers FM/AM stations as preset stations (☞p. 63) or SIRIUS
channels as preset channels (☞p. 72). J1
FM/AM (CATEGORY l / h)
Sets the FM/AM tuner band to FM or AM (☞p. 63). J1
Selects a channel category for a SIRIUS (☞p. 72).
PRESET j / i
Selects an FM/AM preset station (☞p. 64) or a SIRIUS preset channel
(☞p. 73). J1
g
h i jk
rs
n t uv
l
Cursor B / C / D / E Select menu items and change settings when
menus, etc., are displayed.
ENTER
Confirms a selected item.
RETURN
Returns to the previous screen when menus are
displayed, or close the menu.
s USB port
For connecting a USB memory device or portable USB audio player (☞p. 39).
t DISPLAY
u
v
w
x
Switches the display between the Now Playing view and the Browse
view.
YPAO MIC jack
Connect the supplied YPAO microphone and adjust the speaker balance
automatically (☞p. 41).
PHONES jack
For plugging headphones in. Sound effects applied during playback can
also be heard through the headphones.
VIDEO AUX jacks
For connecting game consoles to this unit temporarily (☞p. 36).
TUNING/CH jj / ii
Changes FM/AM tuner frequencies (☞p. 63) or SIRIUS Satellite Radio
channels (☞p. 72). J1
mn o p q
w
x
J 1 : Usable when you have selected TUNER or SIRIUS input.
En
9
INTRODUCTION
Part names and functions
h MONITOR OUT/ZONE OUT jacks (COMPONENT VIDEO
Rear panel
For connecting TV that are compatible with component video signals,
using three cables to output video signal (☞p. 29).
REMOTE IN/OUT1-2 jacks
For connecting an external component that supports the remote
control function (☞p. 37).
TRIGGER OUT 1-2 jack
For connecting an external component that supports the trigger
function to operate it linked with operation of this unit (☞p. 37).
RS-232C terminal
This is a control expansion terminal for custom installation. Consult
your dealer for details.
SIRIUS jack
For connecting a SiriusConnect tuner (sold separately) (☞p. 70).
AV1-4 jacks
For connecting to external components equipped with audio/video
outputs to receive audio/video signals (☞p. 32).
ANTENNA jacks
For connecting AM and FM antennas (☞p. 40).
a PHONO jacks
b
c
d
e
f
g
o AV OUT jacks
jacks)
For connecting a turntable (☞p. 35).
DOCK jack
For connecting an optional Universal Dock for iPod (such as YDS12), Wireless System for iPod (YID-W10), or Bluetooth Wireless
Audio Receiver (YBA-10) (☞p. 90, p. 92, p. 94).
NETWORK port
For connecting to a network (☞p. 38).
HDMI OUT 1-2 jacks
For connecting an HDMI - compatible TV to output audio/video
signals (☞p. 29).
MON.OUT/ZONE OUT jacks (S-VIDEO/VIDEO jacks)
For connecting a TV capable of receiving video input, and outputting
video signals to it (☞p. 29, p. 30).
COMPONENT VIDEO jacks
For connecting external components that support component video
output for video signal reception (☞p. 32).
HDMI input jacks
For connecting external components equipped with HDMIcompatible outputs to receive audio/video signals (☞p. 31).
a
c
b
DOCK
de
NETWORK
ARC
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
j
k
l
m
n
f
g
h
i
j
HDMI
HDMI OUT
2
1
AV 1
i
AV 1
AV 2
AV 3
AV 4
AV 5
AV 6
MON.OUT/ZONE OUT
AV 7
Y
PB
PR
Y
AV 3
PB
C
TRIGGER
OUT
PR
AV 1
A
PHONO
MONITOR OUT/ZONE OUT
Y
PB
PR
GND
REMOTE
1
IN
OUT
IN
(SINGLE)
(FRONT)
1
2
D
AV 4
AUDIO 2
AUDIO 3
t
u
2
B
(2 TV)
s
OUT
AV 2
AUDIO 1
r
Distinguishing the input and output jacks
The area around the audio/video output jacks is marked
in white to prevent connection errors. Use these jacks to
output audio/video signals to a TV or other external
component.
RS-232C
COMPONENT VIDEO
q
k
(1 BD/DVD)
ARC
p
For outputting audio/video signals received when analog inputs are
selected (☞p. 38).
AUDIO1-4 jacks
For connecting external components equipped with audio outputs to
receive audio signals (☞p. 35).
MULTI CH INPUT jacks
For connecting a player that supports a multi-channel output
(☞p. 36).
ZONE OUT jacks
Outputs sound of this unit to an external amplifier set in a different
room. (☞p. 147).
PRE OUT terminals
For connecting a subwoofer with built-in amplifier or an external
power amplifier (☞p. 23, p. 26).
SPEAKERS terminals
For connecting the front, center, surround and surround back speakers
(☞p. 20). Connect the presence speakers (☞p. 20) or the speakers for
Zone2 and Zone3 (☞p. 21) to the EXTRA SP jacks.
AC IN
For connecting the supplied power cable.
+12V 0.1A MAX.
MULTI CH INPUT
CENTER
ZONE OUT
PRE OUT
HDMI
HDMI OUT
2
1
AUDIO 4
(3 CD)
ARC
SELECTABLE
AV 1
AV 2
AV 3
AV 4
AV 5
AV 6
AV 7
(1 BD/DVD)
ARC
1
AV OUT
TRIGGER
OUT
COMPONENT VIDEO
MON.OUT/ZONE OUT
Y
PB
PR
Y
AV 3
PB
C
PR
AV 1
A
2
Y
PB
PR
REMOTE
1
IN
OUT
IN
1
2
OUT
AV 2
2
B
D
AV 4
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
SURROUND
SUR. BACK
(REAR)
SUBWOOFER
AUDIO 1
CENTER
(2 TV)
SPEAKERS
SURROUND
ZONE2/ZONE3
SURROUND BACK/
BI-AMP
CENTER
FRONT
ZONE2/ZONE3/
F.PRESENCE
AUDIO 4
MULTI CH INPUT
CENTER
ZONE OUT
PRE OUT
(SINGLE)
SURROUND
SUR. BACK
(FRONT)
1
2
CAL
FM
AUDIO 3
(3 CD)
AC IN
FRONT
e OPTICAL f COAXIAL
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
ZONE 3
CENTER
SPEAKERS
ANTENNA
75
AUDIO 2
+12V 0.1A MA
ZONE2/ZONE3
HD Radio (4 RADIO)
GND AM
EXTRA SP2
SURROUND
SURROUND BACK/
BI-AMP
CENTER
FRONT
EXTRA SP1
SINGLE
EXTRA SP2
SINGLE
Output jacks
l
m
n
o p
q
r
s
t
u
En
10
INTRODUCTION
Part names and functions
j ENHANCER indicator
Front panel display
k
a Tuner indicator
Light up according to the status of a received station (☞p. 63).
b HD indicator
c
d
e
f
g
h
i
l
Lights up when this unit is tuned into the HD Radio station (☞p. 66).
TAG indicator
Lights up when the selected HD Radio program (or song being
played) supports iTunes Tagging (☞p. 67).
ZONE2/ZONE3 indicator
Lights up when the audio or video output to Zone2 or Zone3 is
enabled (☞p. 149).
SLEEP indicator
Blinks when the sleep timer is on (☞p. 13, p. 149).
PARTY indicator
Lights up when the party mode is active (☞p. 122).
Multi information display
Displays a range of information on menu items and settings.
VOLUME indicator
Displays the current volume level.
HDMI indicator
Lights up during normal HDMI communication.
IN indicator
Lights up when this unit detects the external component connected to
the HDMI input jack (☞p. 31).
OUT 1/OUT 2 indicators
Indicate which HDMI OUT jack outputs audio/video signals (☞p. 29).
d e f
ab c
ij
k
n
o
Lights when the adaptive dynamic range control feature is tuned on
(☞p. 60).
■ Switching information on the front panel display
The front panel can display sound programs and surround
decoder names as well as the active input source.
Press uINFO repeatedly to cycle through displayed
informations. J2
Center speaker
Subwoofer 1
Front L speaker
Subwoofer 2
Front R speaker
Presence L speaker
Surround L speaker
Surround back L
speaker
Input source name
AV1
Standard
VOLUME
Sound program (DSP program)
Presence R speaker
Surround R speaker
Surround back
speaker J1
Surround back R
speaker
g
PARTY
STEREO TUNED
ENHANCER
m
p ADAPTIVE DRC indicator
Lights up when the Compressed Music Enhancer is active (☞p. 53).
CINEMA DSP indicator
Lights up when a sound field effect that uses CINEMA DSP
technology is selected.
CINEMA DSP 3D indicator
Lights up when CINEMA DSP 3D is activated (☞p. 52).
Cursor indicators
Light up if corresponding cursors on the remote control are available
for operations.
MUTE indicator
Blinks when audio is muted.
Speaker indicators
Indicate speaker terminals from which signals are output.
h
MUTE VOLUME
ADAPTIVE DRC
SLEEP
l
m
nm
o
p
J 1 : “SB” is displayed when using a 6.1-channel configuration only.
J 2 : During FM/AM reception, the frequency is displayed instead of the input source. During SIRIUS Satellite Radio signals reception, the channel is displayed instead of the input source.
En
11
INTRODUCTION
Part names and functions
a Remote control signal transmitter
Remote control
Transmits infrared signals.
b SOURCE A (SOURCE Power)
Switches an external component on and off.
a
c Display window
Displays remote control information.
SOURCE RECEIVER
b
l
m
c
AV
d
1
2
5
6
3
4
7
V-AUX
3
4
AUDIO
1
2
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
1
2
f
PROGRAM
3
MUTE
4
VOLUME
n
o
g
h
ON SCREEN
OPTION
p
RETURN
DISPLAY
q
TAG
PRG SELECT
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
r
PRESET
TV
f PROGRAM k / n
s
g External component operation keys
Operate recording, playback, and menu displays etc. for external
components (☞p. 129). J1
h ON SCREEN
Selects a preset station when the FM/AM tuner or SIRIUS Satellite
Radio tuner is operated.
k TV control keys
Operate a monitor such as a TV.
l RECEIVER A (RECEIVER Power)
Switches this unit between on and standby mode.
m SOURCE/RECEIVER
Switches remote control key function to operate this unit or an
external component (☞p. 129). Operate an external component when
this key glows green, or this unit when this key glows orange.
n VOLUME +/Adjust the volume level (☞p. 48).
o MUTE
Turns the mute function of the sound output on and off (☞p. 48).
p OPTION
Turns on and off the Option menu (☞p. 58).
q DISPLAY
Switches the display between the Now Playing view and the Browse
view.
r HD Radio / SIRIUS Satellite Radio keys
HOLD
TAG
PRG SELECT
Remains the current artist name and song title
displayed (☞p. 68, p. 74).
Stores “tag” data to the iPod or internal memory
of this unit (☞p. 67).
Selects an HD Radio audio program (☞p. 66).
s Sound selection keys
Switch between the current sound field effect (sound program) and the
surround decoder (☞p. 51).
Turns on and off the ON SCREEN menu.
PURE
DIRECT
INPUT
k
e SCENE
Selects a sound program (☞p. 51). Press the up or down key
repeatedly to cycle through sound programs.
REC
j
[A]
AV1-7 jacks
Front panel VIDEO AUX jacks
AUDIO1-4 jacks
PHONO jacks
MULTI CH INPUT jacks
A USB storage device connected to the USB port.
Rhapsody service, SIRIUS internet radio, internet
radio, a USB connected to the USB port, or a PC
connected to the NETWORK port.
A Universal Dock for iPod, Wireless System for
iPod, or Bluetooth Wireless Audio Receiver
connected to the DOCK jack.
FM/AM tuner
A SIRIUS Satellite Radio tuner connected to the
SIRIUS jack.
Changes the external component to operate with
the gExternal component operation keys
without changing inputs. J1
Switch the input source and the sound program with a single button
(☞p. 50). When this unit is in standby mode, press this key to switch
on.
ENTER
HOLD
TUNER
SIRIUS
POP-UP/MENU
TOP MENU
i
g
Select an input source on this unit from which to playback.
DOCK
SCENE
e
Cursor B / C / D / E Select menu items and change settings when
menus, etc., are displayed.
ENTER
Confirms a selected item.
RETURN
Returns to the previous screen when menus are
displayed, or close the menu.
j PRESET F / G
d Input selector
AV1-7
V-AUX
AUDIO1-4
PHONO
MULTI
USB
NET
i Cursor B / C / D / E, ENTER, RETURN
TV VOL
TV CH
MUTE
J 1 : You can use gExternal component operation keys for each input source to operate registered components. Remote control codes must be registered for each input
in advance if you want to operate external components (☞p. 131).
En
12
INTRODUCTION
Part names and functions
Remote control with the cover open
t Sound selection keys
Switch between the current sound field effect (sound program) and the
surround decoder (☞p. 51).
u INFO
SOURCE RECEIVER
Cycles the information displayed on the front panel display (the name
of the currently selected input source, the sound program, the
surround decoder, the FM/AM tuner frequency, etc.).
v Numeric keys
2
5
6
3
4
7
V-AUX
w PARTY
x
AUDIO
1
2
PHONO
DOCK
3
4
MULTI
USB
NET
TUNER
SIRIUS
[A]
y
SCENE
1
2
PROGRAM
3
MUTE
4
VOLUME
ON SCREEN
Switches the party mode on and off (☞p. 149).
HDMI OUT
Switches the output jack connected to an HDMI compatible TV
(☞p. 48).
Radio control keys
Operates the FM/AM tuner or SIRIUS Satellite Radio tuner. These
keys are used when using the tuner input.
MEMORY
FM
AM
(CATEGORY D / E)
TUN./CH H / I
POP-UP/MENU
TOP MENU
When inserting batteries in the remote control, remove the
battery compartment cover from the reverse side of the remote
control, and insert four AAA batteries into the battery
compartment so that they match with the polarity markings (+
and -).
Enter numbers.
AV
1
■ Installing batteries in the remote control
OPTION
Presets radio stations.
Sets the FM/AM tuner band to FM.
Sets the FM/AM tuner band to AM.
Selects a category of the SIRIUS Satellite Radio
channel.
Changes tuning frequencies or SIRIUS Satellite
Radio channels.
Switches this unit to standby mode automatically after a specified
period of time has elapsed (sleep timer). Press this key repeatedly to
set the time for the sleep timer function.
DISPLAY
t
SUR.
DECODE
ENHANCER
PARTY
u
INFO
MEMORY
FM
1
2
3
4
5
6
HDMI OUT
120min.
w
x
Off
90min.
30min.
60min.
CATEGORY
AM
The SLEEP indicator lights up when the sleep timer is on.
y
TUN./CH
v
a
c
b
Battery compartment
Replace the batteries with new ones if the remote control can
only be operated within a narrow range.
z SLEEP
ENTER
RETURN
Battery compartment
cover
NOTE
If there are remote control codes for external components
registered to the remote control, removing the batteries for more
than 2 minutes, or leaving exhausted batteries in the remote
control, may clear the remote control codes. If this should occur,
replace the batteries with new ones, and set the remote control
codes.
A LEVEL
Adjusts the output level for each speaker (☞p. 114).
7
8
9
SLEEP
z
10
0
ENT
LEVEL
A
ZONE
SETUP
B
C
B SETUP
Setup this remote control (☞p. 130).
C ZONE
Switches the zone to be operated by the remote control between the
Main zone, Zone2, and Zone3 (☞p. 149).
En
13
INTRODUCTION
Part names and functions
On-screen display
When a TV is connected to this unit, the supplied remote control can be used to specify and verify this
unit’s settings via menus and options displayed on the TV screen.
The following displays are available in the on-screen display.
Content window
ON SCREEN menu
Press hON SCREEN to display the ON
SCREEN menu.
Press dInput selector to display the content
window.
Detailed settings for this unit can be
configured. Use this menu to select desired
settings, change their values, or check the
current status of this unit.
Refer to “SETUP” (☞p. 98) for details.
Includes the Browse view and the Now
Playing view. The Now Playing view displays
the status of the source from which music is
currently played back. Adjust settings for
music content from the Browse view.
Refer to “Confirming and operating input
sources from the content window” (☞p. 62)
for details.
Option menu
Press pOPTION to display the Option menu.
Configure the optional settings for each input
source. Settings such as “Tone Control” and
“Volume Trim” are applied to this unit
regardless of the input source.
Refer to “Configuring settings specific to an
individual input source (Option menu)”
(☞p. 58) for details.
En
14
CONNECTIONS
Connecting speakers
This unit uses acoustic field effects and sound decoders to bring you the impact of a real movie theater or concert hall. These effects will be brought to you with ideal speaker positioning and
connections in your listening environment.
Speaker channels and functions
■ Front left and right speakers
The front speakers are used for the front channel sounds (stereo
sound) and effect sounds.
■ Surround left and right speakers
■ Surround back left and right speakers
The surround speakers are for effect and vocal sounds while
playing back more than 5.1-channel source. When used with no
surround back speaker while playing back more than 6.1-channel
source (including surround back channel), sound of surround back
channel is distributed between the left and right surround speakers.
The surround back speakers are for rear effect sounds while
playing back more than 6.1-channel source. When used with only
one surround back speaker while playing back more than 7.1channel source, sound of the left and right surround back channel is
mixed and output from a single speaker.
E.g.
E.g.
E.g.
Front speaker layout:
Place these speakers at an equal distance from the ideal listening
position in the front of the room. When using a projector screen,
the appropriate top positions of the speakers are about 1/4 of the
screen from the bottom.
■ Center speaker
The center speaker is for the center channel sounds (dialogue,
vocals, etc.).
Surround speaker layout:
Place the speakers at the rear of the room on the left and right sides
facing the listening position. They should be placed between 60
degrees and 80 degrees from the listening position and with the
speaker tops at a height of 4.9 – 5.9 ft. (1.5 – 1.8 m) from the floor.
■ Presence left and right speakers
The presence speakers are used for front effect sounds. When used
in combination with the sound programs (☞p. 54), a sound with a
richer and more spatial presence is possible.
Surround back speaker layout:
When used with 7.1ch sound, arrange the left and right speakers
towards the listening position, to the rear of the listening position.
Arrange the left and right speakers at least 1 ft. (30 cm) apart. The
same separation as with the front left and right speakers is optimum.
When used with 6.1ch sound, arrange these to the rear of the
listening position.
■ Subwoofer
The subwoofer speaker is used for bass sounds and low-frequency
effect (LFE) sounds included in Dolby Digital and DTS. Use a
subwoofer that is equipped with built-in amplifier.
E.g.
Center speaker layout:
Place it halfway between the left and right front speakers. When
using a TV, place the speaker just above or just under the center of
the TV with the front surfaces of the TV and the speaker aligned.
When using a screen, place it just under the center of the screen.
E.g.
Presence speaker layout:
Place the left and right presence speakers 1.6 – 3.3 ft. (0.5 – 1 m) to
the outside of the left and right front speakers respectively. The
tops of the presence speakers should be 5.9 ft. (1.8 m) above the
floor.
E.g.
Subwoofer speaker layout:
Place it to the outside of the front left and right speakers facing
slightly inward to reduce echoes from the wall. You can use one or
two subwoofers and select the position of subwoofers from “Left +
Right,” “Front + Rear” and “Monaural x2” (☞p. 113).
En
15
CONNECTIONS
Connecting speakers
Speaker layout
■ Enjoying the 7.1 channel audio source
■ 7.1-channel speaker layout (7 speakers + subwoofer)
In addition to the 7.1-channel speaker layout, a variety of speaker configurations can be specified with
presence speaker connection, bi-amp connection or the Zone2/Zone3 function.
In addition, this unit is equipped with the “Power Amp Assign” function, which can be used to easily
apply the appropriate speaker settings to this unit according to speaker configuration.
Front R speaker
Subwoofer
Front L speaker
Surround R
speaker
■ Connection of speakers
Connect the speakers to the appropriate jacks shown in the table for each speaker layout. Refer to
“Connecting speakers and subwoofers” (☞p. 20) for details on connecting speakers.
You can also use two subwoofers by connecting them to both SUBWOOFER1 (FRONT) and
SUBWOOFER2 (REAR) jacks. And, you can use the EXTRA SP1 jacks for Zone3 speakers and
EXTRA SP2 jacks for Zone2 by setting the assignment with “Power Amp Assign” (☞p. 112).
Center speaker
■ Assigning a speaker configuration
A speaker configuration must be assigned to this unit to activate the speakers. Use the Power Amp
Assign function to apply the appropriate settings shown in the table for each speaker layout. Refer to
“Power Amp Assign” (☞p. 112) for details on setting.
12 in (30 cm)
or more
Surround L speaker
Surround back L speaker J1
Surround back R speaker
Audio from a 7.1-channel audio source can be played back with no degradation with this speaker
configuration.
■ Connections of speakers
FRONT jacks
Front L/R speakers
SURROUND
BACK jacks
Surround back L/R speakers
CENTER jack
Center speaker
SUBWOOFER
(PRE OUT) jack
Subwoofer
SURROUND jacks
Surround L/R speakers
■ Assigning a speaker configuration
Power Amp Assign
7ch Normal (Default)
J 1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back
speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.
En
16
CONNECTIONS
Connecting speakers
■ Adding the presence speakers for a richer sound field effect
■ Enjoying the audio source without surround back speakers
■ Presence speaker layout (7 speakers + subwoofer + presence speakers)
■ 5.1-channel speaker layout (5 speakers + subwoofer)
Front R speaker
Front L
speaker
Front R speaker
Presence R speaker
Front L speaker
Subwoofer
Presence
L speaker
Subwoofer
Surround R
speaker
Surround R
speaker
Center speaker
Center speaker
Surround back
R speaker
Surround L speaker
12 in (30 cm)
or more
Surround L speaker
Surround back L speaker J1
This unit automatically selects the presence speakers or surround back speakers to output sounds
according to the selected sound program.
When the sound program is changed, the speakers that output the sound are switched between the
presence speakers and surround back speakers automatically. J2
■ Connections of speakers
FRONT jacks
Front L/R speakers
SURROUND
BACK jacks
Surround back L/R speakers
CENTER jack
Center speaker
SUBWOOFER
(PRE OUT) jack
Subwoofer
SURROUND jacks
Surround L/R speakers
EXTRA SP1 jacks
Presence L/R speakers
This unit can mix 7.1-channel audio source down to 5.1-channel sound. This enables 7.1-channel
sound without surround back speakers.
■ Connections of speakers
FRONT jacks
Front L/R speakers
SURROUND jacks
Surround L/R speakers
CENTER jack
Center speaker
SUBWOOFER
(PRE OUT) jack
Subwoofer
■ Assigning a speaker configuration
Power Amp Assign
7ch Normal (Default)
■ Assigning a speaker configuration
Power Amp Assign
7ch Normal (Default)
J 1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back
speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.
J 2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1
jacks.
En
17
CONNECTIONS
Connecting speakers
■ Using the front speakers that support bi-amp connections for a
■ Using speakers in two rooms (Zone2 function)
■ 5.1-channel speaker layout (Front speakers (Bi-amp) + 3 speakers)
■ 7.1-channel speaker layout + Zone2 (7 speakers (in main zone) + subwoofer (in
main zone) + front speakers (in secondary zone))
high quality sound
Main zone
Front R speaker
(Bi-amp connection)
Front L speaker
(Bi-amp connection)
Subwoofer
Front L speaker
Zone2
Front R speaker Subwoofer
Surround R
speaker
Surround R speaker
Front L speaker
Center speaker
Center speaker
Surround L speaker
Surround L speaker
12 in (30 cm)
or more
Surround back L speaker J1
Using the front speakers that support bi-amp connections reproduces a high quality sound.
FRONT jacks
Front L/R speakers (bi-amp)
SURROUND
BACK jacks
Front L/R speakers (bi-amp)
CENTER jack
Center speaker
SUBWOOFER
(PRE OUT) jack
Subwoofer
■ Connections of speakers
FRONT jacks
Front L/R speakers
SURROUND
BACK jacks
Surround back L/R speakers
CENTER jack
Center speaker
SUBWOOFER
(PRE OUT) jack
Subwoofer
SURROUND jacks
Surround L/R speakers
EXTRA SP1
jacks J3
Zone2 speakers
Surround L/R speakers
■ Assigning a speaker configuration
Power Amp Assign
Surround back R
speaker
In addition to the main room, speakers in another room can also be controlled.
When the built-in amplifier assigned to speakers in another room is turned on, sound output
automatically switches from the surround back speakers to the speakers in the other room. J2
■ Connections of speakers
SURROUND jacks
Front R speaker
5ch BI-AMP
■ Assigning a speaker configuration
Power Amp Assign
7ch + 1ZONE
J 1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back
speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.
J 2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1
jacks.
J 3 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power Amp Assign” (☞p. 112).
En
18
CONNECTIONS
Connecting speakers
■ Using speakers in three rooms (Zone2 and Zone3 functions)
■ Connections of speakers
■ 7.1-channel speaker layout + Zone2 + Zone3 (7 speakers (in main zone) +
subwoofer (in main zone) + front speakers (in secondary and tertiary zones))
FRONT jacks
Front L/R speakers
SUBWOOFER
(PRE OUT) jack
Subwoofer
Main zone
CENTER jack
Center speaker
EXTRA SP1
jacks J4
Zone2 speakers
SURROUND jacks
Surround L/R speakers
EXTRA SP2
jacks J5
Zone3 speakers
SURROUND
BACK jacks
Surround back L/R speakers
Zone2
Front R
speaker
Front R speaker
Front L speaker
Subwoofer
Surround R
speaker
Front L speaker
Zone3
■ Assigning a speaker configuration
Front R
speaker
Power Amp Assign
7ch + 2ZONE
Center speaker
Surround L speaker
Surround back L speaker J1
Surround back
12 in (30 cm) R speaker
or more
Front L speaker
In addition to the main room, speakers in other two rooms can also be controlled.
When the built-in amplifier assigned to speakers in another room is turned on, sound output
automatically switches from the surround back and/or surround speakers to the speakers in the other
rooms. J2, J3
J 1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back
speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.
J 2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1
jacks.
J 3 : Sound cannot be output from the surround speakers when it is output from the speakers connected to the EXTRA SP2 jacks.
J 4 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power Amp Assign” (☞p. 112).
J 5 : EXTRA SP2 jacks can also be assigned to the Zone2 speakers with “Power Amp Assign” (☞p. 112).
En
19
CONNECTIONS
Connecting speakers
Connecting speakers and subwoofers
Connect your speakers to their respective terminals on the rear panel.
CAUTION
• Remove the power cable of this unit from the power outlet before connecting the speakers.
• Generally speaker cables consist of two parallel insulated cables. One of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the “+”
(positive, red) terminal on this unit and the speakers, and the other cable into the “–” (negative, black) terminal.
• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP
WIRES!” will appear on the front panel display when this unit is switched on.
■ Front/Center/Surround/Surround back speaker and
Subwoofer connection
When connecting only one surround back speaker, connect the
speaker to the SURROUND BACK L (SINGLE) jacks.
■ Presence speaker connection
When using the presence speakers, connect the speakers to the
EXTRA SP1 jacks as shown in the diagram below.
Presence speaker
Front speaker
R
L
Subwoofer
The presence speakers (PL/PR) that output front effect sounds can
be connected to this unit. With the sound programs (☞p. 58),
sound with a richer and more spatial presence can be created.
R
L
1.8 m
HDMI
AV 2
AV 3
AV 5
AV 6
0.5 – 1 m
PL
PR
L
R
1.8 m
RS-232C
RS-232C
AV 4
0.5 – 1 m
AV 6
AV 7
AV 7
DVD)
PR
Y
AV 3
PB
C
TRIGGER
OUT
TRIGGER
OUT
OMPONENT VIDEO
PR
Y
MONITOR OUT/ZONE OUT
PB
PR
1
REMOTE
1
IN
OUT
IN
PRE OUT
(SINGLE)
(FRONT)
SURROUND
SUR. BACK
((REAR))
SUBWOOFER
REMOTE
1
2
OUT
IN
OUT
IN
SINGLE)
(FRONT)
UR. BACK
((REAR))
SUBWOOFER
OUT
2
2
D
AV 4
MULTI CH INPUT
CENTER
+12V 0.1A MAX.
+12V 0.1A MAX.
ZONE OUT
1
1
2
2
URROUND
SUR. BACK
SUBWOOFER
SURROUND
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
SURROUND BACK/
BI-AMP
CENTER
SINGLE
R
L
Surround
speaker
R
L
Surround back
speaker
Connection of presence speakers is recommended to take full
advantage of the effects of CINEMA DSP sound programs.
1
2
CENTER
FRONT
ZONE2/ZON
F.PRESEN
EXTRA SP1
CENTER
CENTER
FRONT
ZONE2/ZONE3/
F.PRESENCE
AC IN
Continues to the
next page
EXTRA SP1
Center speaker
En
20
CONNECTIONS
Connecting speakers
■ Bi-amp connection
This unit can be connected to speakers that support bi-amp
connections. When connecting speakers, connect the FRONT jacks
and the SURROUND BACK/BI-AMP jacks as in the diagram
below. Configure the bi-amp settings to activate connections.
■ Multi-zone audio system using the internal
amplifier of this unit
Connect the speakers in the second zone and the third zone to the
EXTRA SP1/EXTRA SP2 jacks as in the diagram below.
Zone3 J1
SPEAKERS
Zone2 J1
FRONT
SURROUND BACK/
BI-AMP
ZONE2/ZONE3
ZONE2/ZONE3/
F.PRESENCE
■ Changing speaker impedance
This unit is configured for 8 Ω speakers at factory setting.
When connecting to 6 Ω speakers, carry out the following
procedure to switch to 6 Ω. When this unit is configured for 6 Ω
speakers, 4 Ω speakers can also be used as the front speakers.
1
2
Switch this unit to the standby mode.
Press MAIN ZONE A while pressing and holding
STRAIGHT on the front panel.
Release the keys when “ADVANCED SETUP” is displayed on
the front panel display.
After approximately a few seconds, the top menu item is
displayed. J2
SINGLE
MAIN ZONE A
DOCK
NETWORK
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
HDMI
HDMI OUT
2
1
SELECTABLE
AV 2
AV 1
AV 3
AV 5
AV 6
Y
PB
PR
Y
AV 3
PB
C
TRIGGER
OUT
PR
AV 1
A
Y
GND
MONITOR OUT/ZONE OUT
PB
PR
REMOTE
1
IN
OUT
1
2
IN
OUT
AV 2
2
B
D
AV 4
AUDIO 1
(2 TV)
AUDIO 2
EXTRA SP1
AV 7
COMPONENT VIDEO
MON.OUT/ZONE OUT
PHONO
EXTRA SP2
RS-232C
AV 4
(1 BD/DVD)
ARC
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
CENTER
+12V 0.1A MAX.
ZONE OUT
PRE OUT
(SINGLE)
(FRONT)
SURROUND
SUR. BBACK
(REAR)
FER
SUBWOOFER
1
2
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
SUR. BACK
SUBWOOFER
E2
ZONE
ZONE 3
FRONT/
F. PRESENCE
CENTER
ZONE 3
SPEAKERS
ZONE2/ZONE3
SURROUND
SURROUND BACK/
BI-AMP
CENTER
FRONT
ZONE2/ZONE3/
F.PRESENCE
AC IN
DOCK
NETWORK
FM
ARC
HD Radio (4 RADIO)
GND AM
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
HDMI
HDMI OUT
2
1
ANTENNA
75
SELECTABLE
AV 2
AV 1
AV 3
RS-232C
AV 4
AV 5
AV 6
AV 7
(1 BD/DVD)
ARC
TRIGGER
OUT
COMPONENT VIDEO
MON.OUT/ZONE OUT
Y
PB
PR
Y
AV 3
PB
C
PR
AV 1
A
PHONO
EXTRA SP2
SINGLE
Y
GND
EXTRA SP1
MONITOR OUT/ZONE OUT
PB
PR
REMOTE
1
IN
OUT
PRE OUT
(SINGLE)
(FRONT)
IN
SURROUND
SUR. BACK
(REAR)
SUBWOOFER
1
2
OUT
AV 2
2
B
D
AV 4
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
CENTER
+12V 0.1A MAX.
ZONE OUT
1
2
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
AXIAL
e OPTICAL f COAXIAL
SURRO
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
CENTER
SPEAKERS
ZONE2/ZONE3
SURROUND
SURROUND BACK/
BI-AMP
CENTER
FRONT
ZONE2/ZONE3/
F.PRESENCE
AC IN
ANTENNA
75
NOTE
Before making bi-amplification connections, remove any
brackets or cables that connect a woofer with a tweeter. Refer to
the instruction manuals of speakers for details. When not
making bi-amplification connections, make sure that the
brackets or cables are connected before connecting the speaker
cables.
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
SINGLE
EXTRA SP1
CAUTION
The EXTRA SP jacks of this unit should not be connected to a
Passive Loudspeaker Selector Box or more than one loudspeaker
per channel.
Connection to a Passive Loudspeaker Selector Box or multiple
speakers per channel could create an abnormally low impedance
load resulting in amplifier damage. See this owner’s manual for
correct usage.
Compliance with minimum speaker impedance information for all
channels must be maintained at all times. This information is found
on the back panel of this unit.
STRAIGHT
Continues to the
next page
J 1 : EXTRA SP1 jacks can be assigned to Zone3 and EXTRA SP2 jacks can be
assigned to Zone2 by using “Power Amp Assign” (☞p. 112).
J 2 : Refer to the “Extended functionality that can be configured as needed
(Advanced Setup menu)” (☞p. 139) for details on the Advanced Setup menu.
En
21
CONNECTIONS
Connecting speakers
3
Check that “SPEAKER IMP.” is displayed on the
front panel.
4
5
SPEAKERIMP.
8MIN
Press STRAIGHT repeatedly to select a “6ΩMIN.”
■ Connecting speakers
This type of jack can connect to the following speakers or
connection.
•
•
•
•
•
•
•
Front L/R speakers
Center speaker
Surround L/R speakers
Surround back L/R speakers
Presence L/R speakers
Zone2/Zone3 speakers
Bi-amp connection (Front L/R speakers)
Connecting the banana plug
Tighten the knob, and then insert the banana plug into the end of
the terminal.
+
FR
ON
T
Banana plug
Switch this unit to the standby mode, and then
switch it on again.
The power turns on, when the settings you made has been
configured.
+
3
FR
ON
T
2
1
-
4
1
Remove approximately 0.4 in. (10 mm) of insulation
from the ends of the speaker cables, and twist the
bare wires of the cables together firmly so that they
will not cause short circuits.
2
3
4
Loosen the speaker terminals.
Insert the bare wire of the speaker cable into the gap
on the side of the terminal.
Tighten the terminal.
En
22
CONNECTIONS
Connecting speakers
■ Connecting the subwoofers
PRE
OUT
(SIN
G
LE)
(FR
O
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than
half).
NT)
1
Crossover frequency (if available): Set to maximum.
2
SURR
UND
SUR.
BACK
WOO
FER
CEN
VOLUME
(R
SUB EAR)
CEN
TER
TER
MIN
1
CROSSOVER/
HIGH CUT
Connect the subwoofer input jack to the
SUBWOOFER 1 and/or 2 jack on this unit with an
audio pin cable. J1
MAX
MIN
MAX
Subwoofer examples
NOTE
After connection, applying this setting to this unit is required to
activate all speaker connections. With using “Power Amp
Assign” function, you can easily apply the speaker
configuration.
Refer to “Power Amp Assign” (☞p. 112) for details on using
“Power Amp Assign” function.
J 1 : When only one subwoofer is used, connect the subwoofer to the
SUBWOOFER1 jack.
En
23
CONNECTIONS
Advanced speaker configuration
Speaker layout utilizing an external power
amplifier
More speakers can be used by connecting an external amplifier to this
unit’s PRE OUT jacks. The speaker layout specified using the Power
Amp Assign function varies when an external amplifier is connected.
■ Using a hi-fi amplifier to improve front
■ Using an external amplifier to output the
■ 9.1-channel speaker layout
(7 speakers + subwoofer + external front speakers)
■ 7.1 + Presence speaker layout
(7 speakers + subwoofer + external front presence
speakers)
speaker sound quality
PL
L Front L speaker
PL Front presence L speaker
C Center speaker
PR Front presence R speaker
Speakers that output sound
SR Surround R speaker
SBL Surround back L speaker
EA External amplifier
SBR Surround back R speaker
■ Connections of speakers
Connect the speakers to the following jacks according to the speaker
layout. Refer to “Front/Center/Surround/Surround back speaker and
Subwoofer connection” and “Presence speaker connection” for details
on connecting speakers (☞p. 20). Refer “Connecting an external
amplifier” for details on connecting an external amplifier (☞p. 26).
■ Assigning a speaker configuration
A speaker configuration must be assigned to this unit to activate
speakers and an external amplifier. Use the “Power Amp Assign”
function to easily apply the appropriate speaker settings to this unit
in accordance with speaker configuration.
PR
EA
R
C
L
R
SW
SL
Speakers that output sound
depending upon settings
PL
C
SW
R Front R speaker
SL Surround L speaker
PR
EA
L
Symbols on the table
presence speaker channel
SBL
SBR
SR
The front speaker channel can be enhanced by using an external
amplifier possible of greater output power than this unit.
SL
SBL
SBR
SR
The front presence and surround back speaker channels can be
output at the same time.
■ Connections of speakers
■ Connections of speakers
CENTER jack
Center speaker
SURROUND jacks
Surround L/R speakers
FRONT jacks
Front L/R speakers
SURROUND BACK jacks
Surround back L/R speakers
CENTER jack
Center speaker
External amplifier
(for front L/R speakers)
SURROUND jacks
Surround L/R speakers
SURROUND BACK jacks
Surround back L/R speakers
SUBWOOFER (PRE OUT) jack J1
Subwoofer
F.PRESENCE (PRE OUT) jacks
EXTRA SP1 jacks
Presence L/R speakers
External amplifier
(for presence L/R speakers)
SUBWOOFER (PRE OUT) jack J1
Subwoofer
FRONT (PRE OUT) jacks
■ Assigning a speaker configuration
Power Amp Assign
■ Assigning a speaker configuration
7ch + FRONT
Power Amp Assign
7ch + FPR
J 1 : You can also use two subwoofers by connecting them to both SUBWOOFER1
(FRONT) and SUBWOOFER2 (REAR) jacks.
En
24
CONNECTIONS
Advanced speaker configuration
■ Using the presence speakers in the main
■ Using front speakers that support bi-amp
■ Using front speakers that support bi-amp
■ 9-1-channel speaker layout
(7 speakers + subwoofer + external presence
speakers + front speakers (in secondary zone))
■ 7.1-channel speaker layout
(Front speaker (Bi-amp) + 3 speakers + subwoofer
+ external front presence speakers)
■ 7.1-channel speaker layout
(Front speaker (Bi-amp) + 3 speakers + subwoofer
+ external surround back speakers)
room and speakers in another room
PL
PR
EA
PL
R
R
L
C
BI-AMP
BI-AMP
R
L
SW
SL
SBL
SBR
connection and surround back speakers
PR
EA
BI-AMP
C
L
L
connection and front presence speakers
BI-AMP
C
R
SW
SW
SR
SL
SL
SR
SBL
SBR
SR
EA
The presence speakers in the main room can be used while the
front speakers in another room are used. J1
■ Connections of speakers
A richer sound field can be created with the simultaneous use of
front speakers that support bi-amp connection and front
presence speakers.
■ Connections of speakers
Connecting surround back speakers to an external amplifier
enables simultaneous use of front speakers that support bi-amp
connection and surround back speakers.
■ Connections of speakers
FRONT jacks
Front L/R speakers
CENTER jack
Center speaker
FRONT jacks
Front L/R speakers (bi-amp)
FRONT jacks
Front L/R speakers (bi-amp)
SURROUND jacks
Surround L/R speakers
CENTER jack
Center speaker
CENTER jack
Center speaker
SURROUND BACK jacks
Surround back L/R speakers
SURROUND jacks
Surround L/R speakers
SURROUND jacks
Surround L/R speakers
EXTRA SP1 jacks J2
Zone2 speakers
SURROUND BACK jacks
Front L/R speakers (bi-amp)
SURROUND BACK jacks
Front L/R speakers (bi-amp)
F.PRESENCE (PRE OUT) jacks
External amplifier
(for presence L/R speakers)
F.PRESENCE (PRE OUT) jacks
External amplifier
(for presence L/R speakers)
SUR.BACK (PRE OUT) jacks
External amplifier
(for surround back L/R speakers)
SUBWOOFER (PRE OUT) jack J3
Subwoofer
SUBWOOFER (PRE OUT) jack J3
Subwoofer
SUBWOOFER (PRE OUT) jack J3
Subwoofer
■ Assigning a speaker configuration
Power Amp Assign
7ch + FPR + 1ZONE
J 1 : Sound cannot be output from the surround back speakers when it is output from
speakers connected to the EXTRA SP1 jacks.
J 2 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power
Amp Assign” (☞p. 112).
■ Assigning a speaker configuration
Power Amp Assign
5ch BI-AMP + FPR
■ Assigning a speaker configuration
Power Amp Assign
5ch BI-AMP + SB
J 3 : You can also use two subwoofers by connecting them to both SUBWOOFER1
(FRONT) and SUBWOOFER2 (REAR) jacks.
En
25
CONNECTIONS
Advanced speaker configuration
■ Using front speakers that support bi-amp
connection, surround back speakers and
front presence speakers
■ 9.1-channel speaker layout
(Front speaker (Bi-amp) + 3 speakers + subwoofer
+ external surround back speakers + external front
presence speakers)
PR
PL
BI-AMP
BI-AMP
C
L
R
SW
SL
SBL
SBR
SR
EA
When an external amplifier is used, front presence speakers and
surround back speakers can be used simultaneously with front
speakers that support bi-amp connection. J1
Connecting an external amplifier
Y
The same channel signals are output from the jacks of the PRE
OUT and ZONE OUT terminals as from their corresponding
SPEAKERS terminals. When connecting an external power
amplifier (pre-main amplifier) to enhance speaker output, connect
the input terminals of the power amplifier to the PRE OUT and
ZONE OUT terminals of this unit.
FRONT jacks
Front L/R speakers (bi-amp)
CENTER jack
Center speaker
SURROUND jacks
Surround L/R speakers
SURROUND BACK jacks
Front L/R speakers (bi-amp)
SUR.BACK (PRE OUT) jacks
External amplifier
(for surround back L/R speakers)
F.PRESENCE (PRE OUT) jacks
External amplifier
(for presence L/R speakers)
SUBWOOFER (PRE OUT) jack J2
Subwoofer
REMOTE
1
IN
OUT
IN
(SINGLE)
(FRONT)
1
2
OUT
2
D
AV 4
PUT
CENTER
+12V 0.1A MAX.
ZONE OUT
PRE OUT
1
2
BACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
SURROUND
SUR. BACK
((REAR))
SUBWOOFER
CENTER
SPEAKERS
SURROUND
SURROUND BACK/
BI-AMP
CENTER
FRONT
ZONE2/ZONE3/
F.PRESENCE
NOTES
• When a component is connected to the PRE OUT and ZONE
OUT terminals, do not connect speakers to the SPEAKERS
terminals corresponding to those PRE OUT and ZONE OUT
terminals.
• When an external amplifier equipped with a volume adjustment
function is connected, a sufficient volume level may not be
achieved.
Use of the following components is recommended.
– An amplifier with no volume adjustment function.
– An integrated amplifier equipped with a function that bypasses
volume circuitry, such as the Yamaha A-S2000 with MAIN IN
input.
abcde
f
a ZONE2 jacks
Zone2 channel output jacks.
b ZONE3 jacks
Zone3 channel output jacks.
c FRONT/F.PRESENCE (PRE OUT) jacks
Front channel or front presence channel output jacks.
d SURROUND (PRE OUT) jacks
Surround channel output jacks.
e SUR. BACK (PRE OUT) jacks
f
■ Connections of speakers
MONITOR OUT/ZONE OUT
PB
PR
Surround back output jacks. When you only connect one external
amplifier for the surround back channel, connect it to the SUR.
BACK (SINGLE) jack.
CENTER (PRE OUT) jack
Center channel output jack.
■ Assigning a speaker configuration
Power Amp Assign
5ch BI-AMP + SB + FPR
J 1 : An external amplifier equipped with four channels is required for this speaker
layout.
J 2 : You can also use two subwoofers by connecting them to both SUBWOOFER1
(FRONT) and SUBWOOFER2 (REAR) jacks.
En
26
CONNECTIONS
Connecting external components
Jacks and cables
S-VIDEO jacks
This unit is equipped with the following input/output jacks. Use jacks and cables appropriate for
components that you are going to connect.
To transmit S-video signals that include luminance These jacks transmit conventional analog video
(Y) and chrominance (C) components.
signals.
Use S-video cables.
Use video pin cables.
VIDEO jacks
■ Audio/Video jacks
S-video cable
AV 1
Video pin cable
HDMI jacks
Digital video and digital sound are transmitted through a single jack.
Only use an HDMI cable.
AV 1
HDMI cable
• Use a 19-pin HDMI cable with the HDMI logo.
• We recommend using a cable less than 16.4 ft. (5.0 m) long to prevent signal quality degradation.
• When a TV that supports HDMI functions and Audio Return Channel function is connected, audio
output from the TV can be input to this unit (☞p. 145).
• When a player and TV that support the 3D video format are connected to this unit, 3D content can be
played back.
• If you connect this unit to a component that has a DVI jack, an HDMI/DVI-D cable is required.
■ Analog video jacks
■ Audio jacks
OPTICAL jacks
COAXIAL jacks
These jacks transmit optical digital audio signals.
Use fiber-optic cables for optical digital audio
signals.
These jacks transmit coaxial digital audio signals.
Use pin cables for digital audio signals.
Digital audio fiber-optic cable
Digital audio pin cable
AUDIO jacks
COMPONENT VIDEO jacks
The signal is separated into three components:
luminance (Y), chrominance blue (PB), and chrominance red (PR).
Use component video pin cables with three plugs.
Component video pin cable
These jacks transmit conventional analog audio
signals.
Use stereo pin cables, connecting the red plug to
the red R jack, and the white plug to the white L
jack.
Stereo pin cable
EN
PON
COM
AV 1
A
En
27
CONNECTIONS
Connecting external components
Connecting a TV monitor
When connecting to a non-HDMI compatible TV
This unit is equipped with the following four types of output jack for connection to a TV.
HDMI OUT 1-2, COMPONENT VIDEO, S-VIDEO or VIDEO. Select the proper connection
according to the input signal format supported by your TV.
COMPONENT VIDEO jacks
(MONITOR OUT)
HDMI OUT 1-2 jacks
WORK
ARC
AV 4
AV OUT
SELECTABLE
Input
Output
COMPONENT
VIDEO
COMPONENT
VIDEO
AV 1
AV 2
AV 3
AV 4
AV 5
(1 BD/DVD)
ARC
COMPONENT VIDEO
MON.OUT/ZONE OUT
Y
VIDEO jack
(MONITOR OUT)
PB
PR
Y
AV 3
PB
C
S VIDEO
PR
S VIDEO
AV 1
A
Y
TV
Component
video input
HDMI
HDMI OUT
2
1
Connect to the TV using the same type of connection that you used to connect to the external
component, and change the inputs on your TV to match that of the external component you are using
for playback. If the external component and TV are equipped with different types of analog video
jacks, this unit will convert the component video, S-video or video signal to component video, S-video
or video signal, according to the type of video input jacks used by the TV. J2, J3
MONITOR OUT/ZONE OUT
PB
PR
S-video input
1
IN
AV 2
B
D
AV 4
S-VIDEO jack
(MONITOR OUT)
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
CENTER
ZONE OUT
PRE OUT
VIDEO
(SINGLE)
VIDEO
Video input
AL
d OPTICAL
e OPTICAL f COAXIAL
FRONT
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
SURROUND
SUR. BACK
SU
SPEAKERS
SURROUND
ZONE2/ZONE3
SURROUND BACK/
BI-AMP
CENT
RADIO)
D AM
Through
Converted
When connecting to an HDMI compatible TV
Video signal such as component video, S-video and video received by this unit is converted to HDMI and output to
the TV. Just select HDMI input on the TV to view video from any external source connected to this unit. J1
Input
Output
HDMI
HDMI
TV
HDMI input
COMPONENT
VIDEO
S VIDEO
VIDEO
Through
Converted
J 1 : You can change the resolution and aspect ratio when converting to HDMI to suit your requirements (☞p. 117).
J 2 : Set “Analog to Analog Conversion” to “On” (☞p. 117).
J 3 : Analog to analog conversion is available only for 480i/576i-resolution video signal.
En
28
CONNECTIONS
Connecting external components
■ Connecting an HDMI video monitor
■ Connecting a component video monitor J1
Connect the HDMI cable to one of the HDMI OUT 1-2 jacks.
Connect the component video cable to the COMPONENT VIDEO (MONITOR OUT) jacks.
HDMI input
HDMI
HDMI OUT
2
HDMI
SELECTABLE
AV 1
AV 2
AV 3
AV 4
AV 5
AV
(1 BD/DVD)
ARC
Component video input
HDMI
COMPONENT VIDEO
MON.OUT/ZONE OUT
Y
PB
PR
Y
PB
AV 3
C
PR
COMPONENT
VIDEO
AV 1
A
HDMI
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
Y
SELECTABLE
COMPONEN
Y
HDMI
PB
O
(SINGLE)
(FR
SUR. BACK
((RE
SUBW
PR
B
(1 BD/DVD)
MON.OUT/ZONE OUT
1
IN
AV 2
AV 1
ARC
MONITOR OUT/ZONE OUT
PB
PR
PR
D
AV 4
TV
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
ZONE OUT
CENTER
PRE OUT
Y
PB
PR
ZONE 3
FRONT/
F. PRESENCE
SURROUND
PB
AV 1
Y
A
PHONO
GND
AV 2
B
FRONT
e OPTICAL f COAXIAL
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
SPEAKERS
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
SURROUND
ZONE2/ZONE3
SURROUND BACK/
BI-AMP
CENTER
TV
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
HDMI
75
EXTRA SP2
SINGLE
HDMI
ANTENNA
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
Projector
■ Connecting a S-video monitor J1
Connect the S-video cable to the S-VIDEO (MONITOR OUT) jack.
• Use a 19-pin HDMI cable with the HDMI logo.
• We recommend using a cable less than 16.4 ft. (5.0 m) long to prevent signal quality degradation.
• When a TV that supports the HDMI function and Audio Return Channel function is connected, audio
output from the TV can be input to this unit (☞p. 145).
• When a player and TV that support the 3D video format are connected to this unit, 3D content can be
played back.
• This unit is equipped with HDMI OUT 1 and 2 jacks. The active HDMI OUT jack(s) can be selected
(☞p. 48). The active HDMI OUT jack(s) can be registered with the SCENE function (☞p. 102).
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
AV 1
(1 BD/DVD)
ARC
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
AV 1
A
PHONO
GND
S-video input
AV 2
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
S
VIDEO
S
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
TV
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
J 1 : The video signal for the COMPONENT VIDEO or S-VIDEO jacks is converted and output from HDMI OUT 1-2 jacks.
When connecting to a TV via the HDMI jack, you do not need to use these jacks.
En
29
CONNECTIONS
Connecting external components
■ Connecting a video monitor J1
When using other TVs
Connect the video pin cable to the VIDEO (MONITOR OUT) jack.
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
To transmit sound from the TV to this unit, connect the TV’s audio output to the AUDIO1-4 jacks.
TV audio output
AV 1
(1 BD/DVD)
ARC
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
Connection
Optical digital audio output
Connect to the OPTICAL jack of the AUDIO1 with a fiber-optic cable.
Coaxial digital audio output
Connect to the COAXIAL jack of the AUDIO2 with a digital audio pin
cable.
Analog stereo output
Connect to one of the AUDIO1-4 with a stereo pin cable.
AV 1
A
PHONO
GND
Video input
AV 2
V
AUDIO 1
(2 TV)
B
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
VIDEO
V
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
TV
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
Select the input source connected via TV’s audio output jack to enjoy the TV sound.
If the TV supports optical digital audio output, we recommend that you connect the TV audio output
to the receiver’s AUDIO1 jack.
Connecting to AUDIO1 allows you to switch the input source to AUDIO1 with just a single key
operation using the SCENE function (☞p. 50).
Available input jacks
■ Listening to TV audio
To transmit sound from the TV to this unit, connect as followings according to the TV:
Audio output
(Optical, coaxial, or analog)
DOCK
NETWORK
AUDIO
COAXIAL
OPTICAL
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
AV 1
(1 BD/DVD)
ARC
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
AV 1
A
PHONO
GND
AV 2
B
AUDIO 1
When using a TV that supports the Audio Return Channel function and HDMI
Control function
When your TV supports both HDMI Control (e.g., Panasonic VIERA Link) and Audio Return
Channel functions, audio/video output from the unit to the TV and audio output from the TV to the
unit are possible using a single HDMI cable.
The input source is switched automatically to match operations carried out on the TV, and that
makes TV sound control easier to use.
For the connections and settings, refer to “Single HDMI cable input to TV audio with Audio Return
Channel function” (☞p. 145).
When using a TV that supports the HDMI Control functions
(2 TV)
TV
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
You can control your TV using the receiver’s remote control by entering the TV’s remote control
code (☞p. 131).
When using a TV that supports HDMI Control functions (e.g., Panasonic VIERA Link), if HDMI
Control functions are enabled on the unit, then input source can be switched automatically to match
operations carried out on the TV.
For the connections and settings, refer to “Switching the input source on this unit automatically
when listening to TV audio” (☞p. 144).
J 1 : The video signal for the VIDEO jacks is converted and output from HDMI OUT 1-2 jacks. When connecting to a TV via the
HDMI jack, you do not need to use these jacks.
En
30
CONNECTIONS
Connecting external components
SOURCE RECEIVER
Connecting BD/DVD players and other devices
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
This unit has the following input jacks. Connect them to the appropriate output jacks on
d the playback devices such as BD/DVD players.
AUDIO
Input jack
Video input
Audio input
AV1 J1
HDMI/Component video/S-video/Video
HDMI/Coaxial digital/Analog (Stereo)
AV2 J1
HDMI/Component video/S-video/Video
HDMI/Coaxial digital/Analog (Stereo)
■ Receiving video signals from the HDMI jack and audio signals
from jacks other than HDMI
This unit can use the AV1-4 or AUDIO1-4 input jacks to receive audio signals from
other input jacks.
For example, if a playback device cannot produce audio signals from an HDMI jack,
use the following method to change the audio input.
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV3 J1
HDMI/Component video/S-video/Video
AV 1
HDMI/Optical digital/Analog (Stereo)
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
AV 1
HDMI/Component video/S-video/Video
HDMI/Audio (Optical)
output
HDMI/Optical digital/Analog (Stereo)
AV5
HDMI
HDMI
AV6
HDMI
HDMI
COMPONEN
Y
PB
HDMIPR
AV 1
A
PHONO
AV4 J1
(1 BD/DVD)
ARC
MON.OUT/ZONE OUT
GND
AV 2
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
HDMI
OPTION
ENTER
HDMI
p
i
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
HDMI
HDMI
AUDIO1
—
Optical digital/Analog (Stereo)
AUDIO2
—
Coaxial digital/Analog (Stereo)
AUDIO3
—
Analog (Stereo)
AUDIO4
—
Analog (Stereo)
VIDEO AUX
HDMI/S-video/Video
HDMI/Optical digital/Analog (Stereo)
PHONO
—
Analog (for turntable connection only)
SURROUND
ZONE2/ZONE3
O
AV7
FRONT
e OPTICAL f COAXIAL
OPTICAL
O
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
BD/DVD player
■ Connecting BD/DVD players and other devices with
HDMI cable
Connect the device with an HDMI cable to one of the HDMI jacks of the AV1-7. The
HDMI IN jack of the VIDEO AUX on the front panel can also be used.
Select the input source (AV1-7 or V-AUX) that the playback device is connected to for
playback.
HDMI
AV 1
HDMI output
AV 2
AV 3
AV 4
AV 5
AV 6
AV 7
(1 BD/DVD)
TRIGGER
OUT
COMPONENT VIDEO
Y
PB
HDMI
PR
HDMI
Y
AV 3
PB
C
PR
Y
HDMI
MONITOR OUT/ZONE OUT
PB
PR
1
REMOTE
IN
OUT
IN
PRE OUT
(SINGLE)
(FRONT)
SURROUND
SUR. BACK
((REAR))
SUBWOOFER
1
2
1
2
3
4
5
Press dInput selector to choose an input source (AV1-4, V-AUX,
AUDIO1-4, or PHONO).
Press pOPTION to enter the Option menu.
Press iCursor B / C to choose “Audio Select” and press
iENTER.
Press iCursor D / E to choose an audio input jack and press
iENTER.
Once setup is complete, press pOPTION to close the Option menu.
OUT
2
D
AV 4
AUDIO 4
MULTI CH INPUT
CENTER
+12V 0.1A MAX.
ZONE OUT
1
2
BD/DVD player
FRONT
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
CENTER
SPEAKERS
J 1 : Coaxial digital and optical digital jack function can be assigned to other AV jacks using “Input Assignment.” Refer to “Input Assignment” for details (☞p. 124).
En
31
CONNECTIONS
Connecting external components
■ Connecting BD/DVD players and other devices with component
video cables
Using analog stereo audio output sources
Connect the playback device to the AV1, AV2, AV3, or AV4 jacks.
Connect the device with a component video cable to one of the AV1-4 input jacks.
Component video /
Audio output
Using optical digital audio output sources
DOCK
Connect the playback device to the AV3 or AV4 jacks.
NETWORK
HDMI OUT
2
1
ARC
SELECTABLE
AV 1
ARC
Y
PB
Y
PB
AV 2
AV 3
(1 BD/DVD)
PR
COMPONENT
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
MON.OUT/ZONE OUT
PR
Y
PB
C
PR
AV 1
PR
Component video /
Audio (Optical)
output
A
PHONO
GND
NETWORK
H
HDMI OUT
2
1
ARC
SELECTABLE
AV 1
AV 2
AV 2
B
PB
AV 3
PR
PB
Y
(1 BD/DVD)
ARC
(2 TV)
AV 2
AV 3
AV 4
AV OUT
MON.OUT/ZONE OUT
COMPONENT
Y
COMPONE
Y
PB
PR
Y
AV 3
PB
C
PR
D
AV 4
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
CENTER
ZONE O
L
AV 1
A
Y
AV 2
PR
D
AV 4
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
AUDIO
R
L
B
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
ZONE2/ZONE3
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
Z
SURROUND
ZONE OUT
CENTER
R
PB
ANTENNA
Y
75
b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
OPTICAL
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
FM
HD Radio (4 RADIO)
GND AM
ZON
SURROUND
ZONE2/ZONE3
EXTRA SP2
O
O
ANTENNA
FM
BD/DVD player
HD Radio (4 RADIO)
GND AM
EXTRA SP2
BD/DVD player
Using coaxial digital audio output sources
Connect the playback device to the AV1 or AV2 jacks.
Component video /
Audio (Coaxial)
output
DOCK
NETWORK
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
COMPONENT
VIDEO
HDMI OUT
2
1
AV OUT
SELECTABLE
Y
ARC
AV 1
PB
PR
AV
(1 BD/DVD)
ENT V
MON.OUT/ZONE OUT
Y
PB
PR
Y
AV 1
A
PHONO
GND
AV 2
PR
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INP
(3 CD)
PB
Y
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
COAXIAL
FRONT
e OPTICAL f COAXIAL
SURROUND
SUR.
ZONE2/ZONE3
C
C
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
BD/DVD player
En
32
CONNECTIONS
Connecting external components
■ Connecting BD/DVD players and other devices with S-video
cables
Using analog stereo audio output sources
Connect the playback device to the AV1, AV2, AV3, or AV4 jacks.
Connect the playback device with a S-video cable to one of the AV1-4 input jacks.
DOCK
Using optical digital audio output sources
NETWORK
HDMI OUT
2
1
ARC
Connect the playback device to the AV3 or AV4 jacks.
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
S-video / Audio
output
DOCK
NETWORK
ARC
SELECTABLE
AV 1
(1 BD/DVD)
ARC
AV 1
AV 2
AV 3
AV 4
Y
PB
PB
PR
A
GND
AV 2
B
AUDIO 1
S
COMPONEN
Y
AV 1
PHONO
VIDEO
COMPONEN
MON.OUT/ZONE OUT
AV OUT
(1 BD/DVD)
MON.OUT/ZONE OUT
(2 TV)
(1 BD/DVD)
AV 1
ARC
S
HDMI OUT
2
1
AV OUT
SELECTABLE
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
L
PR
AV 1
AUDIO
A
PHONO
R
GND
S-video / Audio (Optical)
output
AV 2
S
L
B
AUDIO 1
(2 TV)
AUDIO 2
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
R
ANTENNA
VIDEO
75
FM
HD Radio (4 RADIO)
GND AM
S
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
OPTICAL
SURROUND
ZONE2/ZONE3
EXTRA SP2
O
O
BD/DVD player
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
BD/DVD player
Using coaxial digital audio output sources
Connect the playback device to the AV1 or AV2 jacks.
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
AV 1
(1 BD/DVD)
ARC
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
AV 1
A
PHONO
GND
S-video / Audio (Coaxial)
output
AV 2
S
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
VIDEO
S
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
COAXIAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
C
C
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
BD/DVD player
En
33
CONNECTIONS
Connecting external components
■ Connecting BD/DVD players and other devices with video cables
Connect the playback device with a video pin cable to one of the AV1-4 input jacks.
Using analog stereo audio output sources
Connect the playback device to the AV1, AV2, AV3, or AV4 jacks.
Using optical digital audio output sources
DOCK
NETWORK
Connect the playback device to the AV3 or AV4 jacks.
HDMI OUT
2
1
ARC
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV OUT
(1 BD/DVD)
SELECTABLE
Video / Audio
output
AV 1
(1 BD/DVD)
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
AV 1
V
A
PHONO
GND
AV 2
B
COMPONEN
MON.OUT/ZONE OUT
Y
PB
VIDEO
AUDIO 1
(2 TV)
PR
V
AV 1
V
AV 1
ARC
(1 BD/DVD)
ARC
A
PHONO
AV OUT
(1 BD/DVD)
SELECTABLE
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
L
GND
AUDIO
AV 2
Video / Audio (Optical)
output
R
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
L
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
R
VIDEO
ANTENNA
V
75
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
OPTICAL
FM
HD Radio (4 RADIO)
GND AM
SURROUND
ZONE2/ZONE3
O
O
EXTRA SP2
ANTENNA
FM
75
HD Radio (4 RADIO)
GND AM
BD/DVD player
EXTRA SP2
BD/DVD player
Using coaxial digital audio output sources
Connect the playback device to the AV1 or AV2 jacks.
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
AV 1
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
AV 1
V
A
PHONO
Video / Audio (Coaxial)
output
(1 BD/DVD)
ARC
GND
AV 2
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
VIDEO
V
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
COAXIAL
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
C
C
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
BD/DVD player
En
34
CONNECTIONS
Connecting external components
■ Connecting CD players and other audio devices
Using coaxial digital output sources
Connect the playback device to the AUDIO2 jack.
Using analog stereo output sources
Connect the playback device to the AUDIO1, AUDIO2, AUDIO3, or AUDIO4 jacks.
DOCK
NETWORK
HDMI OUT
2
1
ARC
DOCK
NETWORK
AV 1
HDMI OUT
2
1
ARC
SELECTABLE
AV 2
AV 3
AV 4
(1 BD/DVD)
AV 1
SELECTABLE
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
Y
PB
PB
PR
A
GND
COMPONEN
MON.OUT/ZONE OUT
AV OUT
Y
AV 1
PHONO
AV 1
COMPONEN
MON.OUT/ZONE OUT
AV OUT
(1 BD/DVD)
ARC
(1 BD/DVD)
ARC
PR
AV 2
B
AV 1
A
PHONO
AUDIO 1
(2 TV)
GND
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
AV 2
B
AUDIO 1
(2 TV)
Audio output
L
AUDIO
R
AUDIO 2
AUDIO 3
AUDIO 4
Audio (Coaxial) output
MULTI CH
(3 CD)
SIRIUS
L
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
COAXIAL
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
C
C
SURROUND
SURROUND
ZONE2/ZONE3
ANTENNA
ZONE2/ZONE3
75
FM
HD Radio (4 RADIO)
GND AM
R
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
CD player
EXTRA SP2
CD player
We recommend connecting audio devices with a coaxial digital output to the AUDIO2 coaxial digital jack on this
unit. This connection allows you to switch to the AUDIO2 just by pressing the “CD” SCENE key (☞p. 50).
Using optical digital output sources
■ Connecting a turntable
Connect the playback device to the AUDIO1 jack.
Connect the audio output of the turntable to PHONO jacks of this unit. J1
DOCK
NETWORK
HDMI OUT
2
1
ARC
SELECTABLE
AV 1
(1 BD/DVD)
ARC
DOCK
NETWORK
HDMI OUT
2
1
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
COMPONEN
MON.OUT/ZONE OUT
Y
PB
ARC
SELECTABLE
AV 1
(1 BD/DVD)
ARC
PR
AV 1
AV 1
A
PHONO
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
COMPONEN
MON.OUT/ZONE OUT
GND
Y
PB
PR
AV 1
AV 2
Audio output
B
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
A
AUDIO 4
GND
AV 2
MULTI CH
(3 CD)
B
GND
AUDIO 1
(2 TV)
Audio (Optical) output
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
L
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
FRONT
e OPTICAL f COAXIAL
OPTICAL
AUDIO
SURROUND
ZONE2/ZONE3
O
R
L
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
O
75
FM
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
R
ANTENNA
HD Radio (4 RADIO)
GND AM
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
EXTRA SP2
CD player
Turntable
Connect your turntable to the GND terminal of this unit to reduce noise in the signal.
J 1 : When connecting a turntable with a low-output MC cartridge to the PHONO jacks, use an in-line boosting transformer or MC-head amplifier.
En
35
CONNECTIONS
Connecting external components
Connecting game consoles or video camcorders
Connecting a multi-format player or an external decoder
Use the VIDEO AUX jacks on the front panel to temporarily connect devices such as a game console or
video camcorder to the receiver.
Select the V-AUX input to use these connected devices.
This unit has 8 sets of input jacks (FRONT L/R, CENTER, SURROUND L/R, SUR. BACK and
SUBWOOFER) to input multi-channel analog sound signals. If your playback component, such as a
DVD player or SACD player, has multi-channel analog output capability, you can enjoy up to 7.1channel multi-channel sound. To output multi-channel sound, connect the audio output jacks of your
playback component to the MULTI CH INPUT jacks of this unit, and set the input source of this unit to
“MULTI CH.”
■ When connecting an HDMI compatible device
Connect the HDMI output of the device to the HDMI IN jack of the VIDEO AUX.
MULTI CH INPUT
FRONT
Game Console,
Video Camcorder,
etc.
L
R
L
SURROUND
SUR. BACK
R
L
CENTER
SUBWOOFER
R
HDMI
HDMI output
HDMI
HDMI
Center out
Subwoofer out
Surround back out
Front out
Connect the video and audio outputs of the device to the VIDEO or S-VIDEO, and AUDIO or
OPTICAL jacks of the VIDEO AUX.
Surround out
■ When connecting an non-HDMI compatible device
Multi-format player/External decoder
(7.1-channel output)
S
V
L
R
O
S-video output
VIDEO
S
Video output
VIDEO
Game Console,
Video Camcorder,
etc.
V
AUDIO
L
Analog audio output
R
Audio (Optical) output
OPTICAL
• When you select “MULTI CH” as the input source, the digital sound field processor and tone control are
automatically disabled.
• As this unit does not redirect signals input through the MULTI CH INPUT jacks to compensate for
missing speakers, make appropriate settings on the multi-format player or the external decoder that suit
to the speaker configuration.
• When the input source is switched to “MULTI CH,” images input from a component connected to the
AV1-7 or VIDEO AUX jacks can be displayed on a video monitor (☞p. 101). If your DVD player does
not support multi-channel digital output, connect it to these input jacks.
O
• Be sure to turn down the volume when connecting this unit and the other devices.
• When both the HDMI connection and the analog video/audio connection are performed between the
HDMI compatible device and this unit, only the HDMI signal will be input.
En
36
CONNECTIONS
Connecting external components
Connecting a SCENE link playback-compatible device
Using the Trigger function to link external component power
When the components are the Yamaha products and have the capability of the transmission of the
remote control signals, connect the REMOTE IN and REMOTE OUT jacks to the remote control input
and output jack with the monaural analog mini cable as follows.
When this unit is connected to a Yamaha subwoofer that supports the system connection or the
component with TRIGGER IN jack, you can turn on and off the component by using this unit.
System connection input
HDMI
1
AV 2
AV 3
AV 4
AV 5
AV 6
Remote control in
AV 7
(1 BD/DVD)
TRIGGER
OUT
COMPONENT VIDEO
PR
Y
AV 3
PB
C
PR
Y
MONITOR OUT/ZONE OUT
PB
PR
1
1
IN
Yamaha component
(CD or DVD player, etc.)
2
OUT
IN
OUT
2
D
AV 4
MULTI CH INPUT
CENTER
+12V 0.1A MAX.
ZONE OUT
PRE OUT
(SINGLE)
HDMI
2
AV 3
RS-232C
AV 4
AV 5
AV 6
AV 7
DEO
AV 3
(FRONT)
PB
C
PR
OUT
1
Y
MONITOR OUT/ZONE OUT
PB
PR
REMOTE
1
IN
OUT
IN
(SINGLE)
(FRONT)
1
2
OUT
2
2
D
AV 4
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
SURROUND
SUR. BACK
((REAR))
SUBWOOFER
UT
CENTER
CENTER
+12V 0.1A MAX.
ZONE OUT
PRE OUT
1
SPEAKERS
SURROUND
SURROUND BACK/
BI-AMP
CENTER
FRONT
Remote control out
Yamaha subwoofer
that supports the system
connection
2
ACK
SUBWOOFER
ZONE 2
ZONE 3
FRONT/
F. PRESENCE
SURROUND
SUR. BACK
((REAR))
SUBWOOFER
CENTER
SPEAKERS
SINGLE
EX
Infrared signal receiver or
Yamaha component
SURROUND
SURROUND BACK/
BI-AMP
CENTER
FRONT
ZONE2/ZONE3
F.PRESENCE
Trigger input
TRIGGER IN
SINGLE
EXTRA SP1
• When a Yamaha component that supports the SCENE link playback function is connected via the
REMOTE OUT jack, playback begins automatically when the SCENE function is used (☞p. 50).
• If the component connected to the REMOTE OUT jack is not a Yamaha product, set “SCENE IR” in the
Scene menu to “Off” (☞p. 103).
Component with the
TRIGGER IN jack
(Power amplifier or
DVD player, etc.)
Functions of the TRIGGER OUT jack can be specified (☞p. 125).
En
37
CONNECTIONS
Connecting external components
Connecting audio/video recording devices
Connecting to the network
This receiver can transmit selected incoming audio/video signals to external components through the
AV OUT jacks. You can record these input audio and video signals to VCRs or similar devices, or send
them to other TVs or external components.
To connect this unit to your network, plug one end of a network cable (CAT-5 or higher straight cable)
into the NETWORK port of this unit, and plug the other end into one of the LAN ports on your router
that supports the DHCP (Dynamic Host Configuration Protocol) server function. To enjoy Internet
Radio or music files saved on PC and DLNA server such as NAS (Network Attached Storage), each
device must be connected properly in the network.
Video / Audio
input
DOCK
NETWORK
HD
HDMI OUT
2
1
ARC
SELECTABLE
AV 1
AV 2
VIDEO
AV 3
(1 BD/DVD)
ARC
V
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
COMPONENT VIDEO
MON.OUT/ZONE OUT
Y
PB
PR
Y
AV 3
PB
C
PR
VIDEO
AV 1
V
A
PHONO
M
Y
GND
AV 2
S
B
D
AV 4
AUDIO 1
(2 TV)
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
CENTER
AUDIO
ZONE OUT
L
L
R
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
S
• Use an STP (shielded twisted pair) cable (commercially available) to connect a network hub or router
and this unit.
• If the DHCP server function on your router is disabled, you need to configure the network settings
manually (☞p. 121).
R
FRONT
e OPTICAL f COAXIAL
ZONE2/ZONE3
O
SURROUND
SUR. BACK
SUBWOOFER
ZONE 2
NAS
(Network Attached Storage)
ZONE
Internet
OPTICAL
SURROUND
O
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
WAN
PC
EXTRA SP2
LAN
VCR/Audio recorder
HDMI audio/video signals and component video signals cannot be transmitted from these jacks.
Modem
Router
Network cable
DOCK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
AV 1
(1 BD/DVD)
ARC
COMPONEN
MON.OUT/ZONE OUT
Y
PB
PR
AV 1
A
PHONO
GND
AV 2
B
AUDIO 1
(2 TV)
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH
(3 CD)
FRONT
e OPTICAL f COAXIAL
SURROUND
ZONE2/ZONE3
ANTENNA
75
FM
HD Radio (4 RADIO)
GND AM
EXTRA SP2
En
38
CONNECTIONS
Connecting external components
Connecting a USB storage device
Connect a USB memory device or USB portable audio player to the USB port on the front panel of this
unit.
USB memory device or
USB portable audio player
NOTE
Be careful that the USB storage device is facing the correct way when inserted into the USB port of
this unit.
En
39
CONNECTIONS
Connecting the FM/AM antennas
An indoor FM antenna and an AM loop antenna are supplied with this receiver. Connect these antennas
properly to their respective jacks.
AM loop antenna
Position the AM antenna away from the receiver. The
wires of the AM antenna have no polarity.
You can connect either wire to the AM jack or the
GND jack.
Indoor FM antenna
DOCK
NETWORK
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
HD
HDMI OUT
2
1
AV OUT
SELECTABLE
AV 1
AV 2
AV 3
(1 BD/DVD)
ARC
COMPONENT VIDEO
MON.OUT/ZONE OUT
Y
PB
PR
Y
AV 3
PB
C
PR
■ Improving FM reception
We recommend using an outdoor antenna. For more information, consult the nearest authorized
dealer.
■ Improving AM reception
Connect this unit to an outdoor antenna with a 16.4 – 32.8 ft. (5 – 10 m) vinyl-coated wire. Make
sure the AM loop antenna is still connected.
Connecting the GND jack can reduce noise. Connect the jack to a store-bought ground bar or copper
plate with a vinyl-covered wire and bury this new attachment in moist ground.
The GND jack is not to be connected to the ground socket of an electrical outlet.
AV 1
A
PHONO
M
Y
GND
AV 2
B
D
AV 4
AUDIO 1
(2 TV)
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
AUDIO 2
AUDIO 3
AUDIO 4
MULTI CH INPUT
(3 CD)
FRONT
e OPTICAL f COAXIAL
SURROUND
SUR. BACK
ZONE2/ZONE3
75
FM
CENTER
SUBWOOFER
ZONE OUT
ZONE 2
ZONE
SURROUND
HD Radio (4 RADIO)
GND AM
EXTRA SP2
Connecting the AM loop antenna
Press and hold
Insert
Release
Assembling the AM loop antenna
En
40
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
This unit is equipped with a Yamaha Parametric Room Acoustic Optimizer (YPAO) that adjusts the configuration, size, and volume balance of the speakers in order to provide an optimal sound field.
Using YPAO allows you to automatically configure settings, such as adjusting speaker output and acoustic parameters to suit your listening room (the room in which this unit is placed). J1
Be aware of the following when using YPAO.
• The amount of time for measurement varies from about two to ten
minutes according to settings.
• The test tone is output at high volume. Refrain from using this
function at night when it may be a nuisance to others.
• Take care that the test tone does not frighten small children.
YPAO operations can be viewed on the front panel display or
TV screen.
1
Check the following before using YPAO.
2
Place the supplied YPAO microphone at ear height in
your listening position.
Face the head of the YPAO microphone upwards.
This unit
• The headphones are removed.
YPAO microphone
TV
• This unit is connected to the TV correctly.
• The power is turned on.
• The video input to which the video output from this unit has been
selected.
Subwoofer
• The power is turned on.
• Volume is set to approximately half, and the cross-over frequency (if
present) is set to maximum.
VOLUME
MIN
MAX
CROSSOVER/
HIGH CUT
MIN
When positioning the microphone, we recommend that you use
equipment that allows you to adjust the height (such as a tripod)
as a microphone stand. When using a tripod, use the tripod
screws to fix the microphone in place.
MAX
Subwoofer examples
Power Amp Assign
• “Power Amp Assign” applies the appropriate speaker settings to this
unit according to speaker configuration.
Refer to “Speaker layout” and “Speaker layout utilizing an external
power amplifier” for details (☞p. 16, p. 24).
3
Switch this unit on.
Continues to the
next page
J 1 : When you have changed the number of speakers or the locations in which they
are installed, first use YPAO to adjust the speaker balance.
En
41
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
SOURCE RECEIVER
4
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Connect the YPAO microphone to the YPAO
MIC jack on the front panel.
5
Press iCursor B / C to select the “Multi
Position” and press iENTER to set the
number of listening positions to measure.
To measure at the multiple listening positions (up to 8),
press iCursor B / C to select “Yes” and press
iENTER.
AUDIO
To measure at one listening position, press
iCursor B / C to select “No” and press iENTER.
YPAO
ENTER
i
M L T . P o s i t i o n
>YesNo
VOLUME
“Mic On View ON SCREEN” appears on the front
panel display, and the following display appears on the
front panel display or TV screen.
6
Press iCursor B / C repeatedly to select
the “Measure” and press iENTER to start
measurement.
Auto measurement starts in 10 seconds.
• To start the measurement immediately, press
iENTER again.
• To cancel the automatic setup, press iRETURN and
then iENTER.
Display during measurement
YPAO
M e a s u r i n g . . .
Progress0%
VOLUME
RETURN
YPAO
M e a s u r e m e n t
ENTERtoStart
VOLUME
“Multi Position” is set to “Yes” at initial factory
settings. If not necessary, skip this step.
This completes preparation. To achieve more accurate
results, take note of the following when measuring
acoustics.
Continues to the
next page
• It takes a few minutes to accurately measure acoustics
for one position. Keep the room as quiet as possible
while acoustics are measured.
• Wait in a corner of the room, or leave it entirely, while
acoustics are measured to avoid creating an
obstruction between the speakers and the YPAO
microphone.
En
42
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
SOURCE RECEIVER
When “Multi Position” is set to “No” in step 5
The following display appears when measurement
finishes without any problems.
AV
1
2
5
6
3
4
7
V-AUX
YPAO
AUDIO
1
2
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
ENTER
i
M e a s u r e . F i n i s h
Save/Exit
Auto measurement restarts in 10 seconds.
YPAO
M e a s u r e . F i n i s h
Save/Exit
VOLUME
The following illustration shows how to place the
optimizer microphone to optimize the setup of this
unit for eight listening positions for example. Up to 8
listening positions can be measured. J1
8
6
4
When “Multi Position” is set to “Yes” in step 5
The following display appears when measurement at the
first position finishes without any problems.
M L T . P o s i t i o n 2 ?
>YesNo
The following display appears when measurement at
the last position finishes without any problems.
VOLUME
Go to step 8.
YPAO
7
Replace the optimizer microphone at your
choosing position and press iENTER to
restart the automatic measurement.
21 3
7
5
VOLUME
Repeat step 7 until the measurement at all listening
positions are made.
NOTE
If a problem occurs, an error message or report is
displayed either during or after acoustic measurement.
Refer to “When an error message is displayed during
measurement” (☞p. 46), or “When a warning
message is displayed after measurement” (☞p. 46) to
resolve the problem and measure acoustics with
YPAO again.
Continues to the
next page
Go to step 7.
J 1 : Measure from the most frequent listening position, such as
directly in front of the TV, first.
En
43
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
SOURCE RECEIVER
Result
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Displays the results of automatic
acoustics measurement. Refer to
“Reviewing automatic setup parameters”
(☞p. 45) for details.
8
YPAO
AUDIO
ENTER
RETURN
Save/Exit
SAVE
Applies the result to the
speaker setup and
finishes the automatic
measurement. J1
CANCEL
Returns to the previous
screen.
EXIT
Finishes the automatic
measurement without
applying the result to the
speaker setup.
Press iCursor B / C to select “Save/Exit”
and press iENTER.
S a v e / E x i t
Select:Save
VOLUME
10
Press iENTER.
Automatic setup is completed. Disconnect the
YPAO microphone.
The YPAO microphone is sensitive to heat. When you
have finished measuring, store the microphone out of
direct sunlight, and away from locations that may
experience high temperatures, such as on top of AV
equipment.
i
• When the warning message appears on this display,
refer to “When an error message is displayed during
measurement” (☞p. 46) for details.
• Press iRETURN to return to the previous screen.
9
Press iCursor D / E to select “SAVE”
and press iENTER.
YPAO
F I N I S H
DisconnectMic
VOLUME
J 1 : The result of the measurement is assigned to the “Setting Pattern”
currently selected. Refer “Setting Pattern” (☞p. 111) for details
on “Setting Pattern.”
En
44
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
SOURCE RECEIVER
■ Reviewing automatic setup
parameters
The results of automatic acoustics measurement can be
reviewed once measurement is complete.
AV
1
2
5
6
3
4
7
V-AUX
2
Select the desired menu item (or enable a
function) using iCursor B / C / D / E and
iENTER.
AUDIO
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
1
Press iCursor B / C repeatedly to select
“Result” and press iENTER immediately
after the automatic measurement.
Wiring
The Result menu can be viewed only when the
automatic measurement is performed.
The results of acoustics measurement are displayed.
Size
ENTER
RETURN
i
a
c
b
a List of menu items
Menu items available in the Result menu are displayed.
c
Displays the size of the connected
speakers and the bass cross over
frequency (“Bass Crossover”).
• “Large” is displayed when the
connected speaker has the ability to
reproduce the low-frequency signals
effectively.
• “Small” is displayed when the
connected speaker does not have the
ability to reproduce the low-frequency
signals effectively.
Distance
Displays the distance from the listening
position to speakers. The unit for distance
can be switched between “ft” (feet) and
“m” (meter) by pressing
iCursor D / E (☞p. 114).
Level
Displays the result of the adjustment of
each connected speaker output level.
Setup Reload J1
Clears the fine-adjustment with Manual
Setup and reloads the result of automatic
setup. For details, refer to “Reloading
automatic setup parameters.”
b Number of measurement
Indicates the number of measurements for multiple
listening positions.
Diagram
Shows the speaker setup and sound adjustment as diagram.
Displays the speakers connected to this
unit and the polarity of each connected
speaker.
• “Normal” is displayed when the
polarity of the connected speaker is
normal.
• “Reverse” is displayed when the
polarity of the connected speaker is
opposite.
3
Press iRETURN to finish the Result menu.
The result of automatic setup can be fine-tuned
manually by “Manual Setup.” Refer to “Manual
speaker setup” (☞p. 111) for details.
■ Reloading automatic setup
parameters
If you are not satisfied with the fine-adjustment of setup
parameters with Manual Setup, the result of automatic
setup saved on this unit can be reloaded. Select “Setup
Reload” in the Result menu.
NOTE
When automatic setup parameters are reloaded,
manually configured settings are cleared. To avoid
clearing manually configured settings by reloading
automatic setup parameters, see “Prohibiting setting
changes” (☞p. 126).
J 1 : This item is displayed after the fine-adjustment is performed with
“Manual Setup.” Use this item to return the settings to the result
of automatic setup.
En
45
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
SOURCE RECEIVER
■ When an error message is
displayed during measurement
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
See “Error messages” (☞p. 47) for instructions on
resolving the problem and measure acoustics again.
AUDIO
3
Press iCursor E to select “RETRY.”
4
Press iENTER to use YPAO again.
■ When a warning message is
displayed after measurement
See “Warning messages” (☞p. 47) for instructions on
resolving the problem. The speaker causing the problem
can be confirmed from the TV screen display.
When “E-5” or “E-9” is displayed:
Check the error code displayed and use YPAO to
measure acoustics again as described below.
ENTER
i When “E-1,” “E-2,” “E-3,” “E-4” or “E-6” is
displayed:
1
2
3
4
5
Press iENTER.
Press iCursor E to select “EXIT.”
Press iENTER.
Check that the environment is suitable for
accurate measurement.
NOTE
Press iCursor D / E to select a option.
PROCEED:
When “E-5” is displayed, measurement can proceed.
However, the measurement in noisy environment may
reduce the accuracy.
When “E-9” is displayed, resume the aborted step.
RETRY:
Restart measurement from the beginning.
Press iENTER to execute the selected
option.
Press iENTER to terminate YPAO, and
switch the unit to standby mode.
4
Check that the speakers are properly
connected.
When “E-10” is displayed:
Turn on the unit and use YPAO again.
When “E-7” or “E-8” is displayed:
1
2
1
2
3
Press iENTER.
Check that the environment is suitable for
accurate measurement.
1
2
3
4
Press iENTER.
Press iCursor E to select “EXIT.”
Although the results of acoustics measurement can be
applied when a warning message is displayed, optimal
sound will not be achieved. Resolving the problem
and using YPAO to measure acoustics again is
recommended.
To exit YPAO with some options
1
2
Use iCursor B / C to select “Save/Exit”
and press iENTER.
Use iCursor D / E to select one of the
following options and press iENTER.
SAVE:
Exits YPAO applying the results of measurement.
CANCEL:
Returns to the previous screen (warning message
screen).
EXIT:
Exits YPAO without saving the results.
Press iENTER to terminate YPAO, and
switch the unit to standby mode.
Turn on the unit and use YPAO again.
En
46
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
■ Message list
E-8:
No Signal
NOTE
The YPAO microphone could not distinguish a
test tone.
Check that each speaker has been connected
and installed correctly.
If the following messages appear, resolve the problems that have occurred and carry out the
measurement process again.
The YPAO microphone or the YPAO MIC jack
may be broken. Inquire at the retailer where
you purchased this unit, or the nearest Yamaha
service center.
■ When a warning message is displayed before measurement
Connect MIC!
The YPAO microphone is not connected.
Connect the YPAO microphone to the YPAO
MIC jack on the front panel.
Unplug HP!
The headphones are connected.
Remove the headphones.
Memory Guard!
The settings of this unit are protected.
Set “Memory Guard” in the Setup menu to
“Off” (☞p. 126).
E-9:
User Cancel
You have carried out an operation that has
cancelled the measuring process.
Carry out the measuring process again. Do not
operate this unit by, for example, adjusting the
volume.
E-10:
Internal Error
An internal error has occurred.
Carry out the measuring process again. Contact
a Yamaha service center if “E-10” is displayed
again.
■ Error messages
E-1:
No Front SP
The unit was not able to find the front channel.
Check that the left and right front speakers are
connected correctly.
E-2:
No Sur. SP
The unit was only able to find one of side of the
surround channels.
Check that the left and right surround speakers
are connected correctly.
E-3:
No F.PRNS SP
The unit was only able to find one of side of the
presence channels.
Check that the left and right presence speakers
are connected correctly.
E-4:
SBR→SBL
Only one surround back speaker is connected
and only the right side surround back channel
sound is detected.
When only one surround back speaker is
connected, connect to the left side (SINGLE)
terminal.
The noise is too loud, preventing accurate
measurements from being taken.
Measure again in quiet surroundings. Turn off
any devices in the room that may be emitting
noise, or place them further away from the
YPAO microphone.
When this message is displayed, selecting
“PROCEED” will allow you to continue
measuring. However, we recommend resolving
the problem and measuring again, as continuing
measurement without doing so will not give
accurate results.
E-5:
Noisy
E-6:
Check Sur.
E-7:
No MIC
Even though surround left and right speakers
are not connected, only the surround back
speakers are connected.
When using surround back speakers, connection
of the surround left/right speakers is necessary.
The YPAO microphone has been removed.
While measuring, take care not to touch the
YPAO microphone.
Check that the YPAO microphone has been
installed correctly.
■ Warning messages
W-1:
Out of Phase
The speakers displayed are connected with the
opposite polarity. Depending on the type of
speakers you are using and the environment in
which you have them installed, this message
may occur even if the speakers are connected
correctly.
Depending on the type of speakers, “W-1” may
display even if the speakers are connected
correctly.
W-2:
Over 24m/80ft
The speakers displayed are separated from the
listening position by more than 24 m, and
cannot be adjusted correctly.
Install the speakers with 24 m of the listening
position.
W-3:
Level Error
Volume level varies greatly for individual
channels, and cannot be adjusted correctly.
Check that all speakers are installed in the
same surroundings.
Check that the speaker polarity + (positive),
and - (negative) are correct. If these are
connected correctly, you can use the speakers
normally even this message appears.
Check that the speaker polarity + (positive),
and - (negative) are correct.
We recommend the same speakers or speakers
with as similar specifications as possible.
Adjust the volume of the subwoofer.
If “W-2” or “W-3” appears, you can apply measurement results, but they will not give optimal
results. We recommend that you resolve the problem and carry out the measurement process again.
En
47
PLAYBACK
SOURCE RECEIVER
Basic playback procedure
AV
1
2
5
6
3
4
7
V-AUX
AUDIO
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
d
1
2
Turn on external components (TV, DVD
player, etc.) connected to this unit.
Use the dInput selector to select the input
source.
4
Press nVOLUME +/- to adjust the volume.
To mute the output.
Press oMUTE to mute the audio output.
Press oMUTE again to unmute.
■ Selecting the active HDMI OUT jack
Use this function to select the HDMI OUT jack(s) used
to output signal.
Press xHDMI OUT repeatedly to select setting.
The HDMI output setting changes as follows.
The name of the selected input source is displayed on
the front panel display. J1
MUTE
VOLUME
When USB, NET, DOCK, TUNER or SIRIUS is
selected, the content window is displayed (☞p. 62).
n
HDMIOUTSel.
OUT1+2
HDMIOUTSel.
OUT1
HDMIOUTSel.
Off
HDMIOUTSel.
OUT2
o
3
Play the external component that you have
selected as the source input, or select a
radio station on the tuner.
Refer to the instruction manuals provided with the
external component for details on playback.
HDMI OUT
CATEGORY
TUN./CH
x
For details on the following operations, refer to the
corresponding pages:
•
•
•
•
•
•
•
•
•
•
“FM/AM tuning” (☞p. 63)
“Listening to the HD Radio™” (☞p. 66)
“Listening to the SIRIUS Satellite Radio™” (☞p. 70)
“Playing back tunes on the PC” (☞p. 76)
“Playing back tunes on the USB storage devices”
(☞p. 78)
“Listening to the Internet Radio” (☞p. 80)
“Using the Rhapsody® service” (☞p. 82)
“Listening to the SIRIUS Internet Radio” (☞p. 86)
“Playing back tunes from your iPod™/iPhone™”
(☞p. 90)
“Playing back tunes from Bluetooth™ components”
(☞p. 94)
OUT 1+2
Outputs the signal at both the HDMI OUT 1
and HDMI OUT 2 jacks simultaneously.
OUT 1
Outputs the signals at the HDMI OUT 1 jack.
OUT 2
Outputs the signals at the HDMI OUT 2 jack.
Off
Any signals are not output at the HDMI OUT
1 and HDMI OUT 2 jacks. Select this setting
when you do not use the video monitor
connected to one of the HDMI OUT jacks.
• The HDMI OUT jack that utilizes the HDMI Control
function can be selected with “Control Select”
(☞p. 119).
• When “HDMI Control” is set to “On,” the HDMI OUT
jack selected with “Control Select” is automatically
enabled in addition to the HDMI OUT jack selected
here by commands from the external component
supporting HDMI Control connected to the jack
(☞p. 119).
• The active HDMI OUT jack(s) can be registered with
the SCENE function (☞p. 102).
J 1 : You can change the input source name displayed on the front
panel display as necessary (☞p. 99).
En
48
PLAYBACK
Basic playback procedure
■ Adjusting high/low-frequency sound
(Tone control)
You can adjust the balance of the high-frequency range (Treble)
and low-frequency range (Bass) of sounds output from the front
left and right speakers to obtain desired tone.
The tone control of the speakers or headphones can be set
separately. Set the headphone tone control with the headphones
connected.
1
Press TONE/BALANCE on the front panel repeatedly
to select “Treble” or “Bass.”
TONE/BALANCE
2
Press PROGRAM l / h to adjust the output level in
the following frequency range.
Adjustable range
-6.0 dB to +6.0 dB
Adjustment
increments
0.5 dB
The display returns to the previous display soon after you release
the key.
• The tone control settings are not effective when this unit is in the
Pure Direct Mode or “MULTI CH” is selected as an input source.
• If you set the balance extremely off, sounds may not match those
from other channels well.
• The tone control can also be adjusted in the Option menu
(☞p. 60).
PROGRAM l / h
The current setting is displayed on the front panel display.
Tone Control
Treble+0.5dB
VOLUME
En
49
PLAYBACK
Changing input settings with a single key (SCENE function)
This unit has a SCENE function that allows you switch this unit on and change input sources, the settings of Audio Select, HDMI Output, Sound Program, Pure Direct Mode, Tone Control, Adaptive
DRC, and Compressed Music Enhancer with one key.
Selecting a SCENE suited to an external component
SCENE 3
Settings are configured for listening to CD content. Press this key and play back content from the CD
player connected to the AUDIO2 jack on this unit.
At initial factory settings, SCENE functions are configured for the following components.
Select a scene according to the component that will be used for playback.
SCENE 4
Settings are configured for listening to a radio station. Press this key and tune into a radio station.
SCENE
1
2
BD/DVD TV
3
4
CD
RADIO
SCENE 5-12
The nothing is registered on the scenes at initial factory setting. The favorite settings can be registered on the
scenes and reloaded by using “Save” and “Load” in Scene menu. For details, refer to “Scene menu” (☞p. 103).
SCENE 1
Settings are configured for viewing DVD or Blu-ray Disc content. Press this key and play back content
from the DVD or Blu-ray Disc player connected to the AV1 jack on this unit.
• When switching scenes, also change the external component that the remote control operates (☞p. 129).
• We recommend that selecting a scene and editing the SCENE function are performed in the Scene menu
(☞p. 102).
• This unit has eight additional scene functions. After selecting one of these scenes, one of the additional
eight scenes may also be selected (☞p. 103).
• Press and hold eSCENE key for about three seconds to register the current setting to the scene.
SCENE 2
Settings are configured for viewing TV content. Press this key and turn on the TV connected to the
AUDIO1 jack on this unit.
Four scenes are available for different uses, such as playing movies or music. The following settings such as input sources, sound programs, and HDMI Output are provided at initial factory settings.
Settings that are not checked ( ) are not enabled when a scene key is pressed. Use “Load” in the Scene menu to check settings to be enabled. Refer to “Adjusting settings registered with the SCENE function”
for details (☞p. 103).
Audio
Select
Input
SCENE
✓
1
AV1
(BD/DVD
Movie Viewing)
Auto
HDMI
Output
Sound
Program
✓
OUT 1+2 Drama
Pure Direct
Adaptive
Tone Control
Mode
DRC
✓
Compressed CINEMA
Music
DSP 3D
Enhancer
Mode
Dialogue
Lift
Extended
Video
Video
Master
Lipsync
Surround Adjustment Processing Volume
Delay
Setting
Pattern
PEQ
Select
✓
Auto
Bass: 0.0dB
Treble: 0.0dB
On
Off
On
0
Auto
Off
Off
-40.0dB
Auto
0ms
Pattern1
Natural
2
(TV Viewing)
AUDIO1 Auto
OUT 1+2 STRAIGHT Auto
Bass: 0.0dB
Treble: 0.0dB
On
On
On
0
Auto
Off
Off
-40.0dB
Auto
0ms
Pattern1
Natural
3
(CD Music
Listening)
AUDIO2 Auto
OUT 1+2 STRAIGHT Auto
Bass: 0.0dB
Treble: 0.0dB
Off
Off
On
0
Auto
Off
Off
-40.0dB
Auto
0ms
Pattern1
Natural
4
(Radio
Listening)
TUNER ---
OUT 1+2 STRAIGHT Auto
Bass: 0.0dB
Treble: 0.0dB
Off
On
On
0
Auto
Off
Off
-40.0dB
Auto
0ms
Pattern1
Natural
En
50
PLAYBACK
Enjoying favorite sound field effect
SOURCE RECEIVER
This unit is also equipped with a Yamaha digital sound field processing (DSP) chip. Multi-channel playback from almost any audio source can be enjoyed using a variety
of sound decoders and various sound field effect programs stored on the chip. Sound field effect programs built into this unit are called “sound programs.”
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
Selecting sound programs and
sound decoders
This unit offers sound programs in many different
categories suitable for movies, music and other uses.
Choose a sound program that sounds best with the
f source you are playing back, rather than relying on the
name or explanation of the program.
PROGRAM
Sound programs are stored for each input source.
When you change the input source, the sound
program previously selected for that input source is
applied again.
Selecting sound program (☞p. 54):
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
PURE
DIRECT
CLASSICAL category: Press sCLASSICAL
repeatedly J1
s LIVE/CLUB category: Press sLIVE/CLUB
repeatedly J1
ENTERTAIN category: Press sENTERTAIN
repeatedly J1
MOVIE category: Press sMOVIE repeatedly J1
Enjoying surround sound with the
CINEMA DSP function
Turning on Pure Direct Mode (☞p. 53):
Press sPURE DIRECT
Turning on Compressed Music Enhancer
(☞p. 53):
Press tENHANCER repeatedly
surround speakers
Sound program categories
Movie
MOVIE
Sci-Fi
■ Enjoying sound programs without
VOLUME
Program
• You can use the speaker indicators on the front panel
display to check what speakers are currently
outputting sound (☞p. 11).
• You can adjust sound field elements (sound field
parameters) for each of the programs (☞p. 105).
This unit allows you to use virtual surround speakers to
enjoy sound field surround effects, even without any
surround speakers (Virtual CINEMA DSP mode). You
can even enjoy surround sound presence with just a
minimal configuration of the front speakers only.
This unit will switch to Virtual CINEMA DSP mode
automatically when Surround is set to “None” in
Configuration (☞p. 113). J2
■ Enjoying sound programs with
headphones
Even when headphones are connected, you can enjoy the
reproduction sound field presence with ease (SILENT
CINEMA mode). J3
Selecting stereo reproduction (☞p. 53):
Press sSTEREO repeatedly J1
Selecting surround decoder:
SUR.
DECODE
t Press tSUR. DECODE repeatedly J1
ENHANCER
CATEGORY
Turning on Straight decoding mode (☞p. 52):
Press sSTRAIGHT
TUN./CH
J 1 : A sound program, stereo reproduction option or sound decoder
can also be selected by pressing fPROGRAM k / n.
J 2 : However, Virtual CINEMA DSP mode is not available under the
following conditions:
• When headphones are connected to this unit.
• When a “7ch Stereo” or “2ch Stereo” sound program is
selected.
• When Pure Direct Mode or straight decoding mode is selected.
J 3 : However, SILENT CINEMA mode is not available under the
following conditions:
• When a “2ch Stereo” sound program is selected.
• When Pure Direct Mode or straight decoding mode is selected.
En
51
PLAYBACK
Enjoying favorite sound field effect
SOURCE RECEIVER
■ Enjoying more spatial sound fields
■ Enjoying sound programs without
CINEMA DSP 3D mode creates an intensive and
accurate stereoscopic sound field in the listening room.
Connection of presence speakers is recommended to
take full advantage of the effects of CINEMA DSP 3D
mode. Do the following steps. J1
This unit allows you to use virtual presence speakers to
create an intensive and accurate stereoscopic sound field,
even when no presence speakers are connected (Virtual
CINEMA DSP 3D mode). You can even enjoy surround
sound presence with front speakers, center speaker, and
surround speakers.
This unit automatically switches to Virtual CINEMA
DSP 3D mode when presence speakers are not available.
Do the following steps.
(CINEMA DSP 3D mode)
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
AUDIO
• Connect the presence speakers to the EXTRA SP1 jacks
and set the speakers to use (☞p. 20).
• Enable CINEMA DSP 3D in the Option menu (☞p. 58).
When a sound program runs in CINEMA DSP 3D mode,
the CINEMA DSP 3D indicator on the front panel lights
up.
Music
CLASSICAL
HallinVienna
VOLUME
presence speakers
• At minimum, connect the front speakers, center speaker,
and surround speakers.
• Enable the center speaker and surround speakers in
“Configuration” (☞p. 112).
• Enable CINEMA DSP 3D in the Option menu (☞p. 60).
Enjoying unprocessed playback
(Straight decoding mode)
Use straight decoding mode when you want to playback
sound without sound field processing. You can playback
as follows in straight decoding mode.
2-channel sources such as CD
Stereo sound plays through the front left and right
speakers.
Multi-channel playback sources such as BD/
DVD
Plays back audio from a playback source without
applying sound field effects, using an appropriate
decoder to split the signal into multiple channels.
Press sSTRAIGHT to enable the straight
decoding mode.
Lights up
STRAIGHT
STRAIGHT
VOLUME
s
To disable straight decoding mode, press
sSTRAIGHT again.
Movie
MOVIE
Sci-Fi
VOLUME
Previously selected program
J 1 : However, CINEMA DSP 3D mode is not available under the
following conditions:
• When headphones are connected to this unit.
• When a “7ch Stereo” or “2ch Stereo” sound program is
selected.
• When Pure Direct Mode or straight decoding mode is selected.
En
52
PLAYBACK
Enjoying favorite sound field effect
SOURCE RECEIVER
Enjoying Hi-Fi Sound Quality (Pure
Direct Mode)
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Use Pure Direct Mode to enjoy the pure high fidelity
sound of the selected source. When Pure Direct Mode is
enabled, this unit plays back the selected source with the
least circuitry. J1
AUDIO
Press sPURE DIRECT to turn Pure Direct Mode
on. J2
Enjoying stereo playback
Select “2ch Stereo” from the sound programs when you
want to playback 2-channel stereo sound (from the front
speakers only), regardless of the playback source.
Selecting “2ch Stereo” will playback as follows for the
playback of CD and BD/DVD sources.
2-channel sources such as CD
Compressed Music Enhancer improves the sound quality
of the compressed music source closer to its original
depth and width. J3
This mode can be used along with any other DSP modes.
Stereo sound plays back through the front speakers.
Multi-channel sources such as BD/DVD
To disable Pure Direct Mode, press
sPURE DIRECT again.
Enjoying compressed music source
with better sound quality
(Compressed Music Enhancer)
Playback channels other than the front channels in the
playback source are mixed with the front channels and
played back through the front speakers.
Press tENHANCER to turn Compressed Music
Enhancer on.
EnhancerOn
VOLUME
ENHANCER
Press sSTEREO repeatedly to select “2ch
Stereo.”
Music
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
STEREO
2chStereo
Lights up when the Compressed Music Enhancer is
active
VOLUME
To disable Compressed Music Enhancer, press
tENHANCER again.
To disable stereo playback, press any of the
sSound selection keys to select a sound program
other than “2ch Stereo.”
s
PURE
DIRECT
t
ENHANCER
CATEGORY
TUN./CH
J 1 : The following features are disabled in Pure Direct Mode.
• sound program, tone control, PEQ Select, and Adaptive DRC
• displaying and operating the Option menu and ON SCREEN
menu
J 2 : While Pure Direct Mode is on, the front panel display screen turns
off in order to reduce noise. When turning Pure Direct Mode off,
the screen returns on.
J 3 : However, Compressed Music Enhancer is not available in the
following audio:
• Signals of which sampling rate is over 48kHz
• High Definition stream
En
53
PLAYBACK
Enjoying favorite sound field effect
Sound programs
■ Category: ENTERTAINMENT
Sound programs are optimized for video sources such as TV programs and games.
in the table indicates the sound program for CINEMA DSP.
Sports
This program allows the listeners to enjoy stereo sport broadcasts and studio variety
programs with enriched live feeling. In sports broadcasts, the voices of the commentator and
sportscaster are positioned clearly at the center while the atmosphere of the stadium expands
in an optimal space to offer the listeners a feeling of presence in the stadium.
Action Game
This sound field is suitable for action games such as car racing, fighting games and FPS
games. The reality of, and emphasis on, various effects makes the player feel like they are
right in the middle of the action, allowing for greater concentration.
Use this program in combination with Compressed Music Enhancer for a more dynamic and
strong sound field.
Roleplaying Game
This sound field is suitable for role-playing and adventure games. This program adds depth
to the sound field for natural and realistic reproduction of background music, special effects
and dialogue from a wide variety of scenes.
Use this program in combination with Compressed Music Enhancer for a more clear and
spatial sound field.
Music Video
This sound field offers an image of a concert hall for live performance of pop, rock and jazz
music. The listener can indulge oneself in a hot live space thanks to the presence sound field
that emphasizes the vividness of vocals and solo play and the beat of rhythm instruments,
and to the surround sound field that reproduces the space of a big live hall.
Recital/Opera
This program controls the amount of reverberations at an optimum level and emphasizes the
depth and clarity of human voices. “Recital/Opera” offers the reverberations of an orchestra
box in front the listener at the same time as providing the acoustic positioning and feeling of
presence on the stage. The surround sound field is relatively moderate, but the data for
concert hall effects are used to represent the inherent beauty of music. The listener will not
be fatigued even after long hours of opera entertainment.
■ Category: CLASSICAL
This sound field is suitable when listening to music sources such as CDs.
Hall in Munich
This sound field simulates a concert hall with approximately 2500 seats in Munich, using
stylish wood for the interior finishing as normal standards for European concert halls. Fine,
beautiful reverberations spread richly, creating a calming atmosphere. The listener’s virtual
seat is at the center left of the arena.
Hall in Vienna
This is an approximately 1700-seat, middle-sized concert hall with a shoebox shape that is
traditional in Vienna. Pillars and ornate carvings create extremely complex reflections from
all around the audience, producing a very full, rich sound.
Hall in Amsterdam
The large, shoe box shaped hall seats about 2200 around the circle stage. Reflections are
rich and pleasing while the sound travels freely.
Church in Freiburg
Located in the south of Germany, this grand, stone-built church has a pointed tower at 120
meters in height. Its long and narrow shape and the high ceiling enable the elongated
reverberation time and limited initial reflection time. Thus, the rich reverberation rather than
the sound itself reproduces the atmosphere of the church.
Church in Royaumont
This program features the sound field created by the refectory (dining hall) of a beautiful
medieval Gothic monastery located in Royaumont on the outskirts of Paris.
Chamber
This program creates a relatively wide space with a high ceiling like an audience hall in a
palace. It offers pleasant reverberations that are suitable for courtly music and chamber music.
■ Category: LIVE/CLUB
This sound field is suitable when listening to music sources such as CDs.
Village Vanguard
The Jazz club is on 7th Avenue, New York. This small club with the low ceiling makes the
powerful reflections converge toward the stage located in the center.
Warehouse Loft
The warehouse resembles some lofts in Soho. Sound reflects off the concrete walls clearly
with a lot of energy.
Cellar Club
This program simulates a live house with a low ceiling and homey atmosphere. A realistic,
live sound field features powerful sound as if the listener is in a row in front of a small stage.
The Roxy Theatre
This is the sound field of a rock music live house in Los Angeles, with approximately 460
seats. The listener’s virtual seat is at the center left of the hall.
The Bottom Line
This is the sound field at stage front in The Bottom Line, a famous New York jazz club once.
The floor can seat 300 people to the left and right in a sound field offering real and vibrant
sound.
En
54
PLAYBACK
Enjoying favorite sound field effect
■ Category: MOVIE
■ Category: STEREO
Sound programs optimized for viewing video sources such as movies.
Sound programs are optimized for listening to stereo sources.
Standard
This program creates a sound field emphasizing the surround feeling without disturbing the
original acoustic positioning of multi-channel audio such as Dolby Digital and DTS. It has
been designed with the concept of an ideal movie theater, in which the audience is
surrounded by beautiful reverberations from the left, right and rear.
Spectacle
This program represents the spectacular feeling of large-scale movie productions. It
reproduces a broad theater sound field that matches cinemascope and wider-screen movies
with an excellent dynamic range providing everything from very small sound effects to
large, impressive sounds.
Sci-Fi
This program clearly reproduces the finely elaborated sound design of the latest science
fiction and special effects-featuring movies. You can enjoy a variety of cinematographically
created virtual spaces reproduced with clear separation between dialogue, sound effects and
background music.
Adventure
Drama
Mono Movie
This program is ideal for precisely reproducing the sound design of action and adventure
movies. The sound field restrains reverberations but puts emphasis on reproducing a
powerful space expanded widely to the left and right. The reproduced depth is also
restrained relatively to ensure the separation between audio channels and the clarity of the
sound.
This sound field features stable reverberations that match a wide range of movie genres from
serious dramas to musicals and comedies. The reverberations are modest but offer an
optimum 3D feeling, reproducing effects tones and background music softly but cubically
around clear words and center positioning in a way that does not fatigue the listener even
after long hours of viewing.
This program is provided for reproducing monaural video sources such as a classic movie in
an atmosphere of a good old movie theater. The program produces the optimum expansion
and reverberation to the original audio to create a comfortable space with a certain sound
depth.
2ch Stereo
Use this program to mix down multi-channel sources to 2-channels. When multi-channel
signals are input, they are down mixed to 2-channels and output from the front left and right
speakers.
7ch Stereo
Use this program to output sound from all speakers. When you playback multi-channel
sources, this unit down-mixes the source to 2-channels, and then outputs the sound from all
speakers. This program creates a larger sound field and is ideal for background music at
parties, etc.
■ Category: SUR.DECODE (Surround decode mode)
Select this program to playback sources with selected decoders. You can playback 2-channel audio
sources in up to 7-channels using a surround decoder.
q Pro Logic
Reproduces sound using the Dolby Pro Logic decoder. This is suitable for all kinds of audio
sources.
q PLIIx Movie /
q PLII Movie
Reproduces sound using the Dolby Pro Logic IIx (or Dolby Pro Logic II) decoder. This is
suitable for movies. J1
q PLIIx Music /
q PLII Music
Reproduces sound using the Dolby Pro Logic IIx (or Dolby Pro Logic II) decoder. This is
suitable for music. J1
q PLIIx Game /
q PLII Game
Reproduces sound using the Dolby Pro Logic IIx (or Dolby Pro Logic II) decoder. This is
suitable for games. J1
Neo:6 Cinema
Reproduces sound using the DTS Neo:6 decoder. This is suitable for movies.
Neo:6 Music
Reproduces sound using the DTS Neo:6 decoder. This is suitable for music.
J 1 : You cannot select the Dolby Pro Logic IIx decoder in the following conditions:
• When “Surround Back” is set to “None” (☞p. 113).
• When headphones are connected.
En
55
PLAYBACK
Using the TV display to control this unit
SOURCE RECEIVER
This unit features a sophisticated on-screen display (OSD) that helps you to control the amplifier function of this unit. With the OSD, you can view information of the
signals being input and the status of this unit. Visual guidance simplifies operations for menus.
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Basic operations via the TV screen
display
AUDIO
2
Use iCursor D / E to select a Input source
press iENTER.
The input source is selected.
2
Use iCursor D / E to select a scene and
press iENTER.
The scene is selected.
A TV screen is required to display the ON SCREEN
or Option menu. Refer to “Connecting a TV monitor”
for instructions on connecting a TV screen (☞p. 28).
h
This section describes basic operations for configuring
“Input,” “Scene” and “Sound Program” using the OSD.
ON SCREEN
ENTER
RETURN
i Press hON SCREEN.
The ON SCREEN menu is displayed on the TV screen.
■ Selecting an input source
1
Use iCursor B / C to select “Input” and
press iENTER.
• Pressing iRETURN displays the previous menu
screen. Press iRETURN repeatedly to close the ON
SCREEN menu.
• In addition to selecting an input source, detailed
settings for each input source can be configured. Refer
to “Configuring input sources (Input menu)” (☞p. 98)
for details.
■ Selecting a scene
1
• Pressing iRETURN displays the previous menu
screen. Press iRETURN repeatedly to close the ON
SCREEN menu.
• Refer to “Changing input settings with a single key
(SCENE function)” (☞p. 50) for details on the default
scene settings.
• Detailed SCENE function settings can be edited. Refer
to “Editing the SCENE function (Scene menu)”
(☞p. 102) for details.
Use iCursor B / C to select “Scene” and
press iENTER.
Input source icons are displayed at the bottom of the
TV screen.
Scene icons are displayed at the bottom of the TV
screen.
En
56
PLAYBACK
Using the TV display to control this unit
SOURCE RECEIVER
■ Selecting a sound program
1
AV
1
2
3
4
5
6
7
V-AUX
Use iCursor B / C to select “Sound
Program” and press iENTER.
AUDIO
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
NOTES
Menus can be operated and the status of this unit
confirmed from the following three main displays.
• ON SCREEN menu (☞p. 98)
• Option menu (☞p. 58)
• Content window (☞p. 62)
These menus and status features can be used to
configure more various functions in addition to
selecting “Input,” “Scene” and “Sound Program.”
Refer to each references for details on menus and
status.
Sound program icons are displayed at the bottom of the
TV screen.
ENTER
RETURN
i
2
Use iCursor D / E to select a sound
program and press iENTER.
The sound program is selected.
• Pressing iRETURN displays the previous menu
screen. Press iRETURN repeatedly to close the ON
SCREEN menu.
• Refer to “Enjoying favorite sound field effect” (☞p. 51)
for various sound programs.
• You can configure the detailed settings for each sound
program. Refer to “Setting sound program parameters
(Sound Program menu)” (☞p. 105) for details.
En
57
PLAYBACK
Configuring settings specific to an individual input source (Option menu)
SOURCE RECEIVER
This unit has a unique Option menu for each input source. Option menus can be used to enable features such as volume trim for compatible input sources or to display
audio/video data.
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
OPTION
ENTER
RETURN
d
Option menu display and setup
Option menu operations are displayed on the front panel
display or TV screen. TV display is used here to explain
operation.
p
i
1
2
Use dInput selector to select an input
source to which options will be applied.
Press pOPTION.
The Option menu is displayed.
3
Use iCursor B / C to select the desired
setting and press iENTER.
5
Press pOPTION to close the Option menu.
Parameters of the selected item are displayed.
4
Use iCursor D / E to select the desired
item (or enable a function).
The keys on the remote control may not respond for a
few seconds after the Option menu is closed. Should
this occur, select the input source again.
• Press iRETURN to display the previous screen or
close the Option menu.
• The Option menu may close automatically when some
functions are enabled.
Option menu
The displayed Option menu settings differ depending
on the input source.
For more information, refer to the “Option menu” on
the next page.
En
58
PLAYBACK
Configuring settings specific to an individual input source (Option menu)
Option menu
The following items are provided for each input source. “✓” indicates the available menu for each input source. J1
USB
PC
NET
RADIO
Rhapsody
SIRIUS IR
DOCK
(iPod)
DOCK
(Bluetooth)
TUNER
SIRIUS
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓ J3
Volume Trim
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Video
Adjustment
✓
✓
✓ J4
✓ J4
Audio Select
✓
✓
✓ J3
✓ J3
Shuffle
✓
✓
✓
✓ J5
Repeat
✓
✓
✓
✓ J5
AV1-4
AV5-7
V-AUX
AUDIO1-4
PHONO
Tone Control
✓
✓
✓
✓
Adaptive DRC
✓
✓
✓
CINEMA DSP
3D Mode
✓
✓
Dialogue
Lift J2
✓
Extended
Surround
MULTI CH
✓
Connect
✓
Disconnect
✓
Pairing
✓
J 1 : When “Tone Control,” “Adaptive DRC,” “CINEMA DSP 3D Mode,”
“Dialogue Lift,” or “Extended Surround” is adjusted for an input source, the
same value is applied to other input sources and “ALL” is displayed on the
front panel display. When settings specific to a certain input source are
selected, the input source name is displayed on the front panel display. If the
name of the input source has been changed (☞p. 99), the original name of the
input source is displayed.
J 2 : “Dialogue Lift” can be adjusted only when the presence speakers are available.
J 3 : This function is only available when “Coax/Opt” is assigned to this input
source from “Input Assignment” in the Setup menu. Refer to “Assigning
component input and output jacks” for details (☞p. 124).
J 4 : This function can be set only when “Component” is assigned to this input
source from “Input Assignment” in the Setup menu. Refer to “Assigning
component input and output jacks” for details (☞p. 124).
J 5 : Not available for Yamaha Wireless System for iPod.
En
59
PLAYBACK
Configuring settings specific to an individual input source (Option menu)
■ Adjusting high/low-frequency sound
Tone Control
■ Enjoying more spatial sound fields
CINEMA DSP 3D Mode
You can adjust the balance of the high-frequency range (Treble)
and low-frequency range (Bass) of sounds output from the front
left and right speakers to obtain desired tone.
Adjustable range
-6.0 dB to +6.0 dB
Adjustment
increments
0.5 dB
When CINEMA DSP 3D is enabled, set whether to use sound
programs in CINEMA DSP 3D mode (☞p. 52).
■ Adjusts the vertical position of dialogues
• “Dialogue Lift” can be adjusted only when the presence speakers
are available.
• You cannot move the dialogue position lower than the default
setting.
■ Selecting the 5.1-channel signal playback
method
Dialogue Lift
Extended Surround
■ Auto-adjusting the sound level to make
Adjusts the vertical position of center sound such as dialogues
when presence speakers are used. Increasing this parameter raises
the position.
even low volumes more audible
Selects whether to reproduce 5.1-channel input signals in 6.1- or
7.1-channel when surround back speakers are used. J2
Auto (Default)
Automatically selects the most suitable decoder if a
flag for reproducing surround back channel is present,
and reproduces the signals in 6.1- or 7.1-channel.
The ideal dialogue
position
q PLIIx Movie
If the dialogue seems to come out from a lower position than the
video monitor screen, increase this parameter.
Always reproduces signals in 7.1-channel using the
Dolby Pro Logic IIx Movie decoder whether or not
surround back channel signals are contained. You can
select this parameter when two surround back
speakers are connected.
q PLIIx Music
Always reproduces signals in 6.1- or 7.1-channel
using the Dolby Pro Logic IIx Music decoder whether
or not surround back channel signals are contained.
You can select this parameter when one or two
surround back speakers are connected.
EX/ES
Automatically selects the most suitable decoder for
input signals whether or not the flag for reproducing
surround back channel is present, and always
reproduces signals in 6.1-channel.
Off
Always reproduces original channels whether or not
the flag for reproducing surround back channel is
present.
Adaptive DRC
Adjusts the dynamic range in conjunction with the volume level
(from minimum to maximum). When this item is set to “On,”
dialogue and sound effects are clearer. J1
Off (Default)
Does not adjust the dynamic range automatically.
On
Adjusts the dynamic range automatically.
When “On” is selected, the dynamic range is adjusted as follows.
On
Off
Input Level
Volume: low
Output Level
Output Level
If the volume level is low, the dynamic range is narrow.
If the volume level is high, the dynamic range is wide.
Move up to the ideal
dialogue position
On
Off
“0” (default) corresponds to the lowest position and “5” to the
highest position.
Input Level
Volume: high
J 1 : “Adaptive DRC” is also effective when you use headphones.
J 2 : AV5-6 or AUDIO1-2 are available when “Audio Return Channel” is on, and
the input source is used for “TV Audio Input.”
En
60
PLAYBACK
Configuring settings specific to an individual input source (Option menu)
■ Adjusting volume between input sources
Volume Trim
■ Selecting audio input jacks
Audio Select
Reduces any change in volume when switching between input
sources by correcting volume differences in each input source. You
can adjust this parameter for each input source.
-6.0 dB to +6.0 dB
Default setting
0.0 dB
Adjustment
increments
0.5 dB steps
■ Selecting a video adjustment preset
Video Adjustment
Repeat
Select the audio input jack through which source signal is input
when an input source is connected to more than one jack.
Auto (Default)
Adjustable range
Automatically selects input signal in the following
order:
(1) HDMI
(2) Digital signal
(3) Analog signal
HDMI
Selects only HDMI signal. When no HDMI signal is
input, no sound is output.
Coax/Opt
Selects only coaxial or optical signal. When no signal
is input, no sound is output.
Analog
Selects only analog signal. If no analog signal is
input, no sound is output.
Selects the desired “Adjustment” (☞p. 118) preset to be applied to
the selected input source.
■ Repeat playback
Plays songs or albums repeatedly. When the repeat function is
enabled, “
(Single / One[iPod])” or “
(All)” appears on
the TV screen. J1
Off
The repeat function is turned off.
Single / One[iPod]
Plays a song back repeatedly.
All
When all songs have completed playback, returns to
the start and repeats playback.
■ Connect / Disconnect Bluetooth
component
Connect
Disconnect
■ Shuffle playback
Shuffle
Plays back songs or albums in random order. When the shuffle
function is enabled, “
” appears on the TV screen. J1
Off
The shuffle function is turned off.
On J2
The shuffle function is tuned on.
Songs J3
Plays songs back in random order.
Albums J3
Plays albums back in random order.
Switches communication with a Bluetooth component on and off
(☞p. 94).
■ Pairing Bluetooth component
Pairing
Performs pairing of this unit and a Bluetooth component (☞p. 94).
J 1 : Not available for Yamaha Wireless System for iPod.
J 2 : This item is displayed only when PC, USB or Rhapsody is selected as input
source.
J 3 : This item is displayed only when DOCK (iPod) is selected as input source.
En
61
PLAYBACK
Confirming and operating input sources from the content window
SOURCE RECEIVER
When USB, NET, DOCK, TUNER or SIRIUS is selected, the content window is displayed on the TV screen. Playback style for iPod, functions for FM/AM tuner, SIRIUS
Satellite Radio, Rhapsody, SIRIUS Internet Radio, Internet Radio, PC, and USB can be set in the content window.
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
d
A TV screen is required to display the content
window. Refer to “Connecting a TV monitor” for
instructions on connecting a TV monitor (☞p. 28).
Displaying the content window on
the TV screen
ENTER
RETURN
DISPLAY
Press dUSB, dNET, dDOCK, dTUNER or
dSIRIUS to display the content window.
i The content window consists of two main displays, the
Now Playing view and the Browse view.
q
Below is the example of the Now Playing view for DOCK
(iPod).
a
b
c
a Image display
b
Icon for each input source or album art is displayed.
Information display
Information on the current input source is displayed.
c Screen button area
Buttons to operate each input source are displayed here.
These buttons vary depending on the selected input. For
details on operations for each input, see the following.
– FM/AM stations (☞p. 64)
– HD Radio stations (☞p. 66)
– SIRIUS channels (☞p. 70)
– PC servers (☞p. 77)
– USB storage (☞p. 79)
– Internet Radio (☞p. 81)
– Rhapsody (☞p. 82)
– SIRIUS Internet Radio (☞p. 86)
– iPod (☞p. 91)
• In the Now Playing view, press iENTER and use
iCursor B / C to select a button. Then press
iENTER to execute the selection.
• In the Browse view, press iCursor E and use
iCursor B / C to select a button. Then press
iENTER to execute the selection.
• Press iRETURN repeatedly to exit from the
operation.
Switching the display between the
Now Playing view and the Browse
view
You can switch the display between the Now Playing
view and the Browse view by the following methods.
• Press qDISPLAY to cycle between the Now
Playing view and the Browse view.
• In the Browse view, press iCursor E and use
iCursor B / C to select the
icon. Then
press iENTER to switch to the Now Playing
view.
Browse view
or
qDISPLAY
or
qDISPLAY
Now Playing view
When selecting “DOCK (iPod)” as input source and
playing back video content of iPod/iPhone, the screen
switches as follows by pressing qDISPLAY
repeatedly.
Now Playing view → Browse view →
Video playback screen (content window disappears)
→ Now Playing view
• In the Now Playing view, press iENTER and
use iCursor B / C to select the
icon.
Then press iENTER to switch to the Browse
view.
En
62
PLAYBACK
FM/AM tuning
SOURCE RECEIVER
When using the FM/AM tuner, adjust the direction of
the FM/AM antenna connected to this unit to get the
best reception.
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
AUDIO
d
Selecting a frequency for reception
(Normal tuning)
1
2
Press dTUNER to switch to the tuner input.
Press yFM or yAM to select a band to
receive.
3
Use yTUN./CH H / I to set a frequency to
receive.
yTUN./CH H
Increases the frequency. Press and hold this key for
longer than a second to search automatically for a station
on a higher frequency than the current one. J1
yTUN./CH I
Decreases the frequency. Press and hold this key for
longer than a second to search automatically for a station
on a lower frequency than the current one. J1
Lights up when a broadcast is received
from a station
STEREO TUNED
ENHANCER
PRG SELECT
FM87.5MHz
STEREO TUNED
VOLUME
ENHANCER
FM98.5MHz
VOLUME
Lights up when a stereo broadcast is received
r
■ Registering stations manually (Manual
Preset)
Select stations manually and register them as presets
individually.
1
Tune in to the station you want to
register, referring to “Selecting a
frequency for reception (Normal
tuning).” J3
2
Use one of the following methods to
register the station you are currently
receiving.
■ Registering to a preset number to which
no station is registered
Press yMEMORY for 3 seconds or longer.
The station will be registered automatically to the
lowest open preset number (or the next number after
the one registered most recently).
■ Entering a frequency number
In normal tuning mode, use the vNumeric keys to
enter a frequency. Leave the decimal point out when
entering a number. J2
For example, enter as follows to select a station on
98.5 MHz.
9
8
Registered frequencies
Preset
STEREO TUNED
ENHANCER
01:FM98.5MHz
Memorized
VOLUME
5
Continues to the
next page
CATEGORY
MEMORY
FM
2
3
AM
y
1
TUN./CH
4
5
6
7
8
9
v
0
J 1 : When searching for a station, release the key once the search has
started.
J 2 : “Wrong Station!” appears on the front panel display when you
enter a frequency that is out of receivable range. Make sure that
the frequency entered is correct.
J 3 : When registering a sub-audio program “HD2” to “HD8” of the
FM HD Radio station, press rPRG SELECT to select the
desired audio program.
En
63
PLAYBACK
FM/AM tuning
SOURCE RECEIVER
AV
1
2
5
6
1
2
PHONO
DOCK
Navigating the FM/AM tuner from
the content window
■ Designating a preset number for
registration
3
4
7
V-AUX
3
4
MULTI
USB
NET
TUNER
SIRIUS
[A]
Press yMEMORY once, to display “Manual Preset”
on the front panel display. After a small wait, the
preset number that the station has been registered to
will appear. J1
AUDIO
d
Preset number
Blinks
Preset
STEREO TUNED
ENHANCER
Empty, or the frequency
registered most
previously
01:Empty
FM98.5MHz
VOLUME
The station currently received can be confirmed from the
menu displayed on the TV screen. Various FM/AM tuner
operations can be performed from the content window
rather than controls on the front panel display. The
content window is displayed when dTUNER is
pressed.
You can operate the FM/AM tuner from the Now
Playing view or the Browse view.
■ Operating from the Now Playing
view
The newly registered frequency
Press jPRESET F / G to select the preset number
to register the station to, and then press yMEMORY
to register.
RETURN
j
PRESET
c
e
d
g
To select a registered station, press
jPRESET F / G to select the preset number
of the station. J2
f
a Tuned indicator
b
c
CATEGORY
y
MEMORY
1
2
3
4
5
6
7
8
9
d
TUN./CH
v
The frequency currently received is displayed.
f Frequency guide
g
The frequency currently received is displayed as a cursor
on the bar.
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
Screen buttons on the Now Playing view
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
Manual Tuning
You can tune in to a desired FM/AM station by
specifying its frequency.
a b
i
ENTER
e Frequency
Lights up when a station is received.
Stereo indicator
Lights up when a stereo broadcast is received. When
“Auto Mode” is set to “Mono,” the indicator does not
light.
Preset number
The selected preset number is displayed.
Band
The selected band (FM or AM) is displayed.
FM
Switches a band to FM.
AM
Switches a band to AM.
Tuning -
Decreases the frequency.
Tuning +
Increases the frequency.
Auto -
Automatically searches for a station on a
lower frequency than the current station.
Auto +
Automatically searches for a station on a
higher frequency than the current station.
Direct
Selects the frequency manually.
Memory
Registers the station currently received as
a preset station. Up to 40 FM/AM stations
can be registered.
0
J 1 : Press iRETURN or wait with no operation for 30 seconds to
exit the Manual Preset mode.
J 2 : To select a station by selecting a preset number, use the
vNumeric keys to enter the preset number of the station you
want to listen. When an invalid number is entered, “Wrong Num.”
appears on the front panel display. Check that you have entered
the correct number.
En
64
PLAYBACK
FM/AM tuning
SOURCE RECEIVER
■ Operating from the Browse view
Preset Select
You can call preset stations.
AV
1
2
5
6
3
4
7
V-AUX
3
4
1 Page Down
AUDIO
1
2
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
ENTER
1 Page Up
Preset -
Selects the previous preset number.
Preset +
Selects the next preset number.
Preset -8
Returns the previous page.
Preset +8
Goes to the next page.
Memory
Registers the station currently received as
a preset station. Up to 40 FM/AM stations
can be registered.
Direct
Selects a station directly by entering the
preset number.
Now Playing
Switches the display to the Now Playing view.
a
b
a Preset station list
The list of preset stations is displayed.
b Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
i
Utility
Auto Mode
Scrolls the list to the next or previous page.
Selects “Auto” or “Mono” when receiving
the FM station (☞p. 63).
Scroll
Screen buttons on the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
Utility
Switches the scroll target.
Browse
Auto Preset
Detects FM stations with a strong signal
and automatically registers up to 40 FM
stations, beginning with the next number
after the current number (☞p. 65). AM
stations cannot be registered by using
“Auto Preset.”
Clear Preset
Clears registration of the preset station
highlighted in the preset station list
(☞p. 65).
Clear All Preset
Clears registration of all preset stations.
Switches the display to the Browse view.
En
65
PLAYBACK
Listening to the HD Radio™
SOURCE RECEIVER
HD Radio technology is a new technology that enables FM and AM radio stations to broadcast programs digitally. Digital broadcasting provides listeners with radically
improved audio quality and reception as well as new data services. Furthermore, supplemental program services allow listeners to select from up to 8 HD Radio programs
multicast on a single FM HD Radio channel. For further information on HD Radio technology, visit “http://www.ibiquity.com/”.
This unit is equipped with an HD Radio reception feature, facilitating CD quality FM broadcasts as well as analog FM stereo quality AM broadcasts. In addition, this unit
can receive both audio and data (such as song titles, artist names, program types, and comments) from all HD Radio programs (HD1 to HD8).
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
• The tuning method for HD Radio stations are same as
analog FM/AM radio stations; however, you only tune
into the analog part of a hybrid HD Radio station
while this unit is in the monaural tuning mode
(☞p. 69).
• This unit is capable of receiving both hybrid and alldigital HD Radio station signals. However, this unit
may not automatically receive all-digital FM station
signals and the automatic tuning operation may stop.
In this case, enter the frequency of the desired alldigital FM HD Radio station directly by using
vNumeric keys (☞p. 63).
PRG SELECT
r
Selecting HD Radio™ audio
programs
The HD indicator lights up in the front panel display
when this unit is tuned into an HD Radio station. In this
state, you can select the desired audio program if the
selected FM HD Radio station provides multiple audio
programs (up to 8).
■ When multiple audio programs are
provided
Lights up when a broadcast is received from a HD
Radio station
TUNED
ENHANCER
FM98.5MHz1
VOLUME
Audio program number (absolute)
■ When only one audio program is
provided
If this unit is tuned into an FM HD Radio station
including only one audio program or an AM HD Radio
station, you cannot select audio programs.
Lights up when a broadcast is received from a HD
Radio station
TUNED
Press rPRG SELECT b / a repeatedly to
select the desired audio programs.
Audio programs can also be selected using
vNumeric keys (1-8) and vENT when this unit is in
the automatic or manual tuning mode. When the selected
audio program is not available currently, “HDx Off” (“x”
indicates the program number) appears.
• When reception for an audio program ceases, the HD
indicator disappears from the front panel display and
HD1 is automatically selected after approximately
20 seconds.
• Some audio programs may not contain data programs
depending on the broadcasting station and the time
period.
ENHANCER
FM98.5MHz
VOLUME
■ Behavior of the display
This unit automatically shows the HD Radio information
(Station Info, etc.) on the front panel display after
3 seconds. You can switch HD Radio information to be
displayed (☞p. 67).
Audio program number (absolute)
TUNED
ENHANCER
FM88.9MHz1
WXYZ-FM<1/3>
VOLUME
Audio program number (relative/total)
CATEGORY
1
2
3
4
5
6
7
8
9
0
ENT
TUN./CH
v
En
66
PLAYBACK
Listening to the HD Radio™
SOURCE RECEIVER
Using the iTunes Tagging
This unit is equipped with the iTunes Tagging that
enables HD Radio listeners to “tag” songs for
subsequent preview and purchase on iTunes.
For details on the iTunes Tagging, visit
“http://www.ibiquity.com/”.
AV
1
2
3
4
5
6
1
2
7
3
V-AUX
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
1
Tune into an HD Radio station and select
HD Radio audio program (if available).
Displaying the HD Radio™
information
If the selected HD Radio program (or song being
played) supports the iTunes Tagging, the TAG
indicator lights up on the front panel display.
You can display the HD Radio information on the front
panel display. J1
Lights up
TUNED
ENHANCER
TAG
r
2
FM88.9MHz1
WXYZ-FM<1/3>
Press uINFO repeatedly to toggle the HD Radio
information display modes as shown below.
Album
Album title, frequency, audio program number (absolute)
Tag Info
The number of iTunes Tagging information files stored
in the internal memory, frequency, audio program
number (absolute)
DSP Program
Current sound field program (☞p. 54), frequency,
audio program number (absolute)
VOLUME
While a song you want to tag is being
played back, press rTAG.
If a song is tagged, “StorageSuccess” and the number
of stored iTunes Tagging information files (up to 50)
appear in the front panel display.
• “Insufficient Data” is displayed on the front panel
display if tagging is not possible.
• If a status or error message is displayed on the front
panel, see “iTunes Tagging” (☞p. 154).
Station Info
Station Info, frequency, audio program number
(absolute)
Audio Decoder
Current audio decoder (☞p. 51), frequency, audio
program number (absolute)
Category
Back to “Station Info”
Program category, frequency, audio program number
(absolute)
Display example (DSP Program)
TUNED
ENHANCER
Artist / Song
FM88.9MHz1
7chStereo
VOLUME
Artist name, song title, frequency, audio program
number (absolute)
CATEGORY
u
INFO
This unit transmits the “tag” data to the iPod/iPhone if an
iPod/iPhone that supports iTunes Tagging is placed in
the Universal Dock for iPod (YDS-12, sold separately)
connected to the DOCK terminal of this unit. Otherwise,
this unit stores the “tag” data (up to 50) in the internal
memory and will transmit it next time your iPod/iPhone
is placed in the dock.
TUN./CH
J 1 : If the HD Radio information contains a character that cannot be
recognized by this unit, the character will be displayed with a
space.
When an information is unavailable, “––––” appears.
En
67
PLAYBACK
Listening to the HD Radio™
SOURCE RECEIVER
a HOLD indicator
Lights up when rHOLD is pressed to activate the hold
Navigating the HD Radio™ tuner
from the content window
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
A HD Radio station currently received can be confirmed
from the menu displayed on the TV screen. Various HD
Radio operations can be performed from the content
d window rather than controls on the front panel display.
The content window is displayed when dTUNER is
pressed.
The HD Radio tuner can be operated from the Now
Playing view or the Browse view.
b
■ Operating from the Now Playing
f
view
ENTER
HOLD
i
r
b
c
d
e
c
d
e
g
a
f
h
g
h
i
j
k
l
m
n
i
j
k
l
m
n
function. The artist name and song title currently received
will remain displayed. Press rHOLD again to cancel the
hold function.
TAG indicator
Lights up when the selected station supports the iTunes
Tagging.
Preset number
The selected preset number is displayed.
Band
The selected band (FM or AM) is displayed.
HD Radio indicator
Lights up when receiving the HD Radio station.
Tuned indicator
Lights up when a station is received.
Frequency
The frequency currently received is displayed.
Frequency guide
The frequency currently received is displayed as a cursor
on the bar.
Channel Name
The channel name currently received is displayed.
Channel Category
The category of the channel is displayed.
Artist Name
The artist name of the current song is displayed.
Song Title
The title of the current song is displayed.
Album Name
The album name of the current song is displayed.
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
Screen buttons on the Now Playing view
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
Manual Tuning
You can tune in to a desired FM/AM station by
specifying its frequency.
FM
Switches a band to FM.
AM
Switches a band to AM.
Tuning -
Decreases the frequency.
Tuning +
Increases the frequency.
Auto -
Automatically searches for a station on a
lower frequency than the current station.
Auto +
Automatically searches for a station on a
higher frequency than the current station.
Direct
Selects the frequency manually.
Memory
Registers the station currently received as
a preset station. Up to 40 FM/AM stations
can be registered.
Program -
Select the previous program of the HD
Radio.
Program +
Select the next program of the HD Radio.
Hold
Activates the hold function. The artist
name and song title currently received
will remain displayed.
Tag
Applies the iTunes Tagging.
En
68
PLAYBACK
Listening to the HD Radio™
SOURCE RECEIVER
■ Operating from the Browse view
Preset Select
You can call preset stations registered.
AV
1
2
5
6
3
4
7
V-AUX
3
4
1 Page Down
AUDIO
1
2
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
ENTER
1 Page Up
Preset -
Selects the previous preset number.
Preset +
Selects the next preset number.
Preset -8
Returns the previous page.
Preset +8
Goes to the next page.
Direct
Selects a station directly by entering the
preset number.
Memory
Registers the station currently received as
a preset station. Up to 40 FM/AM stations
can be registered.
Hold
Activates the hold function. The artist
name and song title currently received
will remain displayed.
Tag
Applies the iTunes Tagging.
i
Now Playing
Switches the display to the Now Playing view.
a
b
a Preset station list
The list of preset stations is displayed.
b Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
Screen buttons on the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
Utility
Audio Mode
Scrolls the list to the next or previous page.
Selects “Auto” or “Mono” when
receiving the FM (or HD Radio) station
(☞p. 66).
Auto
Stereo reception. HD Radio
program is received by
priority.
Mono
Monaural reception.
Reception is better in
monaural mode. HD Radio
program is not received.
Utility
Auto Preset
Detect HD FM, HD AM or analog FM
stations with a strong signal and
automatically registers up to 40 stations,
beginning with the next number after the
current number (☞p. 69). Analog AM
stations cannot be registered by using
“Auto preset.”
Clear Preset
Clears registration of the preset station
highlighted in the preset station list.
Clear All Preset
Clears registration for all preset stations.
Scroll
Switches the scroll target (channel name, channel
category, artist name, song name, or album name).
Browse
Switches the display to the Browse view.
En
69
PLAYBACK
Listening to the SIRIUS Satellite Radio™
To listen to Satellite Radio, you’ll need to connect a SIRIUS Satellite Radio tuner (sold separately) to your Sirius-Ready receiver. SIRIUS Satellite Radio is available to residents of the US (except
Alaska and Hawaii) and Canada.
Satellite Radio delivers a variety of commercial-free music from categories ranging from Pop, Rock, Country, R&B, Dance, Jazz, Classical and many more plus coverage of all the top professional and
college sports including play by play games from select leagues and teams. Additional programming includes expert sports talk, uncensored entertainment, comedy, family programming, local traffic
and weather and news from your most trusted sources.
Once you’ve purchased a SIRIUS tuner you’ll need to activate it and subscribe to begin enjoying the service. Easy to follow installation and setup instructions are provided with the SIRIUS tuner. There
are a variety of programming packages available, including the option of adding “The Best of XM” programming to the SIRIUS service. The “Best of XM” service is not available to SIRIUS Canada
subscribers at this time. Please check with SIRIUS Canada for any updates using the numbers and web address below.
Family friendly packages are also available to restrict channels featuring content that may be inappropriate for children.
To subscribe to SIRIUS, U.S. and Canadian customers can call 1-888-539-SIRI (1-888-539-7474) or visit sirius.com (US) or siriuscanada.ca (Canada).
SIRIUS Radio Legal
SIRIUS and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All other marks and logos are the property of their respective owners. All rights reserved. SIRIUS
subscription sold separately. Taxes and a one-time activation fee may apply. SIRIUS tuner required (sold separately) to receive the SIRIUS service. All programming and fees subject to change. It is prohibited
to copy, decompile, disassemble, reverse engineer, hack, manipulate or otherwise make available any technology or software incorporated in receivers compatible with the SIRIUS Satellite Radio System.
Service not available in Alaska or Hawaii.
Connecting the SiriusConnect™ tuner
Connect the SiriusConnect tuner (sold separately) to the SIRIUS
jack on the rear panel of this unit. For details, see the instruction
manuals provided with the SiriusConnect tuner.
SiriusConnect Tuner
and the antenna
(sold separately)
DOCK
NETWORK
HDMI OUT
2
1
ARC
AV 1
AV 2
AV 3
AV 4
(1 BD/DVD)
AV OUT
SELECTABLE
ARC
MON.OUT/ZONE OUT
PHONO
GND
AUDIO 1
(2 TV)
SIRIUS
a COAXIAL b COAXIAL c OPTICAL d OPTICAL
AUDIO 2
AUDI
(3 CD)
• To ensure optimal reception of the SIRIUS Satellite Radio
signals, the antenna of the SiriusConnect tuner must be placed at
or near a window with no obstacles in the path to the sky. The
orientation of the antenna for the best reception differs depending
on the area. Refer to the instruction manuals provided with the
SiriusConnect tuner for the installation of the antenna. You can
mount it indoors or outdoors.
• Use the Antenna information on the front panel display or the
SIRIUS information screen on the TV screen (☞p. 74) to check
the antenna reception level and adjust the orientation of the
antenna.
• You need to connect the SiriusConnect tuner to the AC wall
outlet.
NOTES
• If “CHECK SR TUNER” or “ANTENNA ERROR” appears on
the front panel display, the connection of the SiriusConnect tuner
or antenna is incorrect. In such cases, check the connection of the
SiriusConnect tuner and the antenna.
• If “NOT SUPPORTED” appears on the front panel display, this
unit does not support the connected SiriusConnect tuner.
e OPTICAL f COAXIAL
T
AN
DC
5V
ANTENNA
75
HD Radio (4 RADIO)
FM
GND AM
EX
To the AC wall outlet
En
70
PLAYBACK
Listening to the SIRIUS Satellite Radio™
SOURCE RECEIVER
Activating SIRIUS Satellite Radio™
subscription
AV
1
2
3
4
5
6
7
V-AUX
AUDIO
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Before using the SIRIUS Satellite Radio feature, you
need to activate your SIRIUS Satellite Radio
subscription. To activate the subscription you need the
d Sirius ID which is uniquely assigned to the
SiriusConnect tuner. Sirius ID is 12-digit number which
is indicated on the package of the SiriusConnect tuner
and on the label of the SiriusConnect tuner. Sirius ID is
also configured on the front panel display when you tune
into the SIRIUS Satellite Radio channel “0.”
■ Displaying the Sirius ID of your
SiriusConnect tuner
CATEGORY
TUN./CH
0
ENT
v
1
Press dSIRIUS.
2
Press v0 and then vENT to display the
Sirius ID of your SiriusConnect tuner.
“000 Sirius ID” and “xxxxxxxxxxxx”
(“xxxxxxxxxxxx” indicates the 12-digit Sirius ID of
your SiriusConnect tuner) appears alternately on the
front panel display.
Write down the Sirius ID in the space provided below.
ID:________________________________________
3
Contact SIRIUS Satellite Radio to activate
your subscription.
SIRIUS Satellite Radio online information
Contact for activation
URL: https://activate.siriusradio.com/
Phone: 1-888-539-SIRIUS (1-888-539-7474)
Status messages appear on the front panel display and
the TV screen during the activation. For details, see
“SIRIUS Satellite Radio™” (☞p. 154). Once the
activation is finished, “SUB UPDATED” appears.
2
Search for a channel by using one of the
SIRIUS Satellite Radio search modes.
All channel search mode
Selects a channel from the all channel list (☞p. 72).
Direct number access mode
Selects a channel directly by entering the channel
number (☞p. 72).
Press dSIRIUS to select “SIRIUS” as the
input source.
The SIRIUS Satellite Radio information (such as
channel number, channel name, category, artist name,
or song title) for the currently selected channel appears
on the front panel display. J1
Channel number
• Before activating your subscription, you can only
select “184” or “000.”
• If a status message or an error message appears on the
front panel display or TV screen, refer to “SIRIUS
Satellite Radio™” (☞p. 154).
Category search mode
Selects a channel by category (☞p. 72).
SIRIUS Satellite Radio™
operations
1
NOTES
Channel name
Traf/Wx
184Weather
CitybyCity/
VOLUME
Preset search mode
Selects a channel from the preset channels (☞p. 73).
You can preset channels by registering them to specific
numbers, and later just select those numbers to tune in.
• SIRIUS Satellite Radio information can be displayed
on the front panel display and the TV screen (☞p. 74).
• If you tune into a channel that you do not subscribe,
“CALL SIRIUS on the front panel display” or “CALL
888-539-SIRIUS TO SUBSCRIBE” appears on the
TV screen.
J 1 : When you select “SIRIUS” as the input source, this unit
automatically calls the previously selected channel.
En
71
PLAYBACK
Listening to the SIRIUS Satellite Radio™
SOURCE RECEIVER
■ All channel search mode
Press yTUN./CH H / I repeatedly to search for
a channel within all channels.
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
NOTE
All channel search mode
AUDIO
AllCH
001Hits1
Pop
VOLUME
• You can search for a channel quickly by pressing and
holding yTUN./CH H / I.
• You can skip channels to the previous or next category
by pressing yCATEGORY D / E.
■ Category search mode
1
When you select the category, the first channel in the
category is selected.
CATEGORY
MEMORY
FM
1
2
3
4
5
6
7
8
9
0
ENT
AM
y
TUN./CH
Press yCATEGORY D / E to select the
channel category.
Category
search mode
Category name
v
Category
Pop
001Hits1
VOLUME
The first channel in the category
If you don’t operate within 10 seconds, the category
search mode returns to “ALL (All Channel Search).”
2
This unit skips the following channels in all channel
search mode or category search mode. This is not a
malfunction.
• channels that are locked (☞p. 74)
• channels that are not currently in service
• channels that you do not subscribe to
■ Direct number access mode
Registering and recalling the
SIRIUS Satellite Radio™ channels
Up to 40 SIRIUS Satellite Radio channels can be
registered as preset channels.
■ Registering preset channels
1
Press the vNumeric keys to enter the desired
three-digit channel number.
For example, to enter the number 123, press “1,” “2” and
then “3” of the vNumeric keys.
• When entering a one-digit or two-digit channel
number, enter the number using the vNumeric
keys and then press vENT to confirm your entry.
• This unit automatically accepts your entry if you do
not press vENT within a few seconds after entering
the number.
• If the selected channel is locked, “PIN:___” appears
on the front panel display. Enter the 4-digit Parental
Lock code number by using the vNumeric keys or
press vENT to cancel (☞p. 74).
• If the selected channel is not available, an advisory
message may appear. For details, refer to “SIRIUS
Satellite Radio™” (☞p. 154).
• If this unit is in preset search mode, a preset number is
selected instead of a channel number when you press
the vNumeric keys. To switch to direct number
access mode, press yTUN./CH H / I.
Search for a channel to be registered.
For details on searching channels, refer to the
following pages.
• All channel search mode (☞p. 72)
• Category search mode (☞p. 72)
• Direct number access mode (☞p. 72)
2
Use one of the following methods to
register the channel currently received.
■ Registering to a preset number for which
no channel has been registered
Press and hold yMEMORY for at least 2 second.
The channel will be automatically registered to the
lowest available preset number (or the next number after
the last to which a channel was registered).
Preset number
Preset01
Registered channel
023HairNath
Memorized
VOLUME
While “Category” is displayed on the front
panel display, press yTUN./CH H / I
repeatedly to search for a channel within
the selected channel category.
You can search for a channel quickly by pressing and
holding yTUN./CH H / I.
En
72
PLAYBACK
Listening to the SIRIUS Satellite Radio™
SOURCE RECEIVER
■ Designating a preset number for
registration
Press yMEMORY once.
AV
1
2
5
6
Displaying the SIRIUS Satellite
Radio™ information
3
4
7
V-AUX
3
4
Preset number
(Blinks)
AUDIO
1
2
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Preset01
Previously registered channel (or “---”
if no channel has been registered)
023HairNatn
001Hits1
You can display the SIRIUS Satellite Radio information
on the front panel display. J1
Signal reception level
Search mode
Pop
Channel number
008Big'80s
VOLUME
NOTE
VOLUME
If a status message or an error message appears on the
front panel display or TV screen, see “SIRIUS
Satellite Radio™” (☞p. 154).
Signal reception level
Signal reception is shown in four levels.
Channel to be registered
Press jPRESET F / G to select the preset number to
which the channel will be registered and then press
yMEMORY to register.
i
RETURN
To cancel registration, press iRETURN or do not
operate the remote control for about 30 seconds.
■ Recalling a preset channel (Preset
■ Front panel display
Press uINFO repeatedly to toggle the SIRIUS
Satellite Radio information display modes as
shown below.
DSP Program
Current sound program (☞p. 54), channel number
Artist/Song
Audio Decoder
Artist name, song title, channel number
Current Audio Decoder (☞p. 51), channel number
Search mode)
Specify preset numbers to recall registered channels.
j
PRESET
Composer
Preset number
Back to “Artist/Song”
Composer name, channel number
Preset01
008Big'80s
Pop
VOLUME
Antenna Level
Press jPRESET F / G to change the preset
numbers (1 to 40).
CATEGORY
INFO
MEMORY
1
2
3
4
5
6
7
8
9
u
y
TUN./CH
v
Antenna reception level, channel number
• Preset numbers to which no channel has been
registered are skipped.
• Preset numbers can also be selected by pressing
vNumeric keys.
0
J 1 : If the SIRIUS Satellite Radio information contains a character
that cannot be recognized by this unit, the character will be
displayed with a space.
When an information is unavailable, “––––” appears.
En
73
PLAYBACK
Listening to the SIRIUS Satellite Radio™
SOURCE RECEIVER
AV
1
5
2
3
6
4
7
V-AUX
d Channel number
Navigating the SIRIUS Satellite
Radio™ tuner from the content
window
The channel number currently received is displayed.
The channel name currently received is displayed.
f Channel Category
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
The SIRIUS Satellite Radio channel currently received
can be confirmed from the menu displayed on the TV
d
screen. Various SIRIUS Satellite Radio operations can
be performed from the content window rather than
controls on the front panel display. The content window
is displayed when dSIRIUS is pressed.
The SIRIUS Satellite Radio tuner can be operated from
the Now Playing view or the Browse view.
■ Operating from the Now Playing
ENTER
HOLD
Parental Lock
Restricts the access to specified channel.
The category of the channel is displayed.
AUDIO
1
Utility
e Channel Name
view
i
r
h
i
j
The artist name of the current song is displayed.
Song Title
The title of the current song is displayed.
Composer Name
The composer name of the current song is displayed.
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
b
c
e
j
a HOLD indicator
Lights up when rHOLD is pressed to activate the hold
function. The artist name and song title currently received
will remain displayed. Press rHOLD again to cancel the
hold function.
Signal reception level
Indicates the signal reception level.
1
Use iCursor D / E to select a number, and
press iENTER to enter the selected
number.
2
3
Repeat step 1 to enter the desired 4-digit
code number.
Screen buttons on the Now Playing view
Radio Control
Select a channel for reception.
Preset -
Select the previous preset number.
Preset +
Select the next preset number.
CAT -
Select the previous category.
CAT +
Select the next category.
CH -
Scan channels downwards from the
current channel.
CH +
Scan channels upwards from the current
channel.
Memory
Register the current channel as a preset
number. Up to 40 channels can be
registered.
Direct
Specify a specific channel by manually
entering the channel number.
Hold
Weak signal
When the parental lock function is enabled for a
particular channel, that channel is skipped in all channel
search mode and category search mode.
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
a
d
f
g
h
i
b
g Artist Name
Strong signal
c Preset number
Use iCursor C to select “Enter,” and press
iENTER to confirm the 4-digit code
number.
Selecting “Clear” and pressing iENTER clears all
the code entered.
4
Use iCursor B / C to select the category
and press iENTER.
Continues to the
next page
Activates the hold function. The artist
name and song title currently received
will remain displayed.
The selected preset number is displayed.
En
74
PLAYBACK
Listening to the SIRIUS Satellite Radio™
SOURCE RECEIVER
5
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
Use iCursor B / C to select the channel to
be locked and press iENTER.
Check mark
AUDIO
i
ENTER
When iENTER is pressed, the selected channel is
received for confirmation. Each time iENTER is
pressed after that, lock switches between on and off.
RETURN
To lock channels in other categories, press
iRETURN to display the category selection screen,
and follow the procedure described above.
CATEGORY
1
2
3
4
5
6
7
8
9
TUN./CH
0
v
NOTES
• If a code number is already registered and the different
code number is entered, “Wrong Number” appears.
Use iCursor B / C to select Parental Lock and
press iENTER, and then enter the correct number.
• If you forget the parental lock code or want to change
it, reset it using “SR PIN” (☞p. 140).
Receiving locked channels
Use direct number access mode (☞p. 72) or preset
search mode (☞p. 73) to receive locked channels. When
a locked channel is received, “Locked” is displayed
followed by the parental lock code input screen. Use
vNumeric keys to enter the 4-digit code.
Browse
Now Playing
Switches the display to the Browse view.
Switches the display to the Now Playing view.
■ Operating from the Browse view
a
b
a Preset station list
The list of preset stations is displayed.
b Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
Screen buttons on the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
Utility
Parental Lock
Restricts the access to specified channel
(☞p. 74).
Clear Preset
Clears registration of the preset station
highlighted in the preset station list.
Clear All Preset
Clears registration of all preset stations.
1 Page Up
Scroll
Switches the scroll target (channel name, channel
category, artist name, song title, or composer name).
1 Page Down
Scrolls the list to the next or previous page.
En
75
PLAYBACK
Playing back tunes on the PC
SOURCE RECEIVER
You can enjoy playback of audio files stored on PCs connected to this unit via your network. To play back audio files on your PC, you need to install Windows Media
Player on the PC and configure the media sharing setting of Windows Media Player.
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
d
If you do not use a DHCP server, configure the
network parameters (IP address, etc.) of this unit
manually (☞p. 121).
Windows Media Player setup
1
ENTER
i
Install Windows Media Player on your PC.
You can download the installer of Windows Media
Player from the Microsoft website, or use the upgrade
function of the installed Microsoft Windows Media
Player.
Playback of PC music contents
Screen buttons on the Browse view
For a complete list of status messages that appear on
the front panel display and GUI screen, see “USB and
Network” (☞p. 155).
The PC music contents can be operated from the menu
displayed on the TV screen.
You can operate the PC contents from the Now Playing
view or the Browse view.
■ Operating from the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
10 Pages Up
10 Pages Down
Goes to 10 pages forwards or backwards.
1 Page Up
RETURN
2
Activate Windows Media Player first, enable the media
sharing and then select this unit as a device to which
the media is shared.
NOTES
• Some security software installed on your PC (antivirus software, firewall software, etc.) may block the
access of this unit to your PC. In such cases, configure
the security software appropriately.
• You can connect this unit to up to 16 PC servers, and
each server must be connected to the same subnet as
this unit.
1 Page Down
a b c
Turn on your PC then allow media sharing.
e
f
Scrolls the list to the next or previous page.
d
g
h
a
b
c
d
e
f
g
h
Repeat icon
Shuffle icon
Play icon
Current directory name
Menu items
Album art / Input icon
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
Current menu number / Number of all menu items
Now Playing
Switches the display to the Now Playing view.
1
2
Press dNET repeatedly to select “PC” as
the input source.
Press iCursor B / C to select a PC server
and music file to play back.
• To select a PC server, folder or file, press
iCursor B / C.
• To confirm the selection, press iENTER.
• To return to the previous menu, press iRETURN.
3
Press iENTER to start playback.
The Now Playing view appears during playback.
En
76
PLAYBACK
Playing back tunes on the PC
SOURCE RECEIVER
■ Operating from the Now Playing
view
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
a b c
Screen buttons on the Now Playing view
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
Play Control
AUDIO
Operates the basic playback functions of PC.
e
f
d
h
i
a
b
c
d
e
g f
g
i
ENTER
PRG SELECT
h
i
g
Repeat icon
Shuffle icon
Play icon
Album image
Artist name
Album title
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
Song title
Elapsed time
• You can switch the information displayed on the front
panel display by pressing uINFO (☞p. 11).
• Album images are available only when the file
contains image data.
p (Play)
Starts playback.
s (Stop)
Stops playback.
e (Pause)
Stops playback temporarily.
b (Skip -)
Skips to the beginning of the currently
playing song. Press iENTER at the
beginning of the song to skip to a previous
song.
a (Skip +)
Skips to the beginning of the next song.
■ Compatibility of Digital Media
Controller
A DLNA-compliant Digital Media Controller (DMC)
device can also be used to control music playback. Refer
to “Using a PC to control this unit over a network”
(☞p. 100) for details. J1, J2
CAUTION
When DMC controls are used to adjust volume,
playback volume may be unexpectedly loud. This
could result in damage to this unit or the speakers.
“Max Volume” can be used to specify the maximum
volume level to prevent excessively loud playback
(☞p. 116).
■ Operating basic playback functions
with the remote control
Scroll
Switches the scroll target (artist name, album title, or
song title).
Browse
Switches the display to the Browse view.
Use the following remote control keys to operate
(playback, stop, skip, etc.) your PC contents.
gp
Play
gs
Stop
ge
Switches between playback and pause.
ga
Skip forward during playback
gb
Skip backward during playback
■ Shuffle/repeat playback
Use the Option menu to apply playback shuffle and
repeat settings. Refer to “Shuffle playback” (☞p. 61)
and “Repeat playback” (☞p. 61) for details.
CATEGORY
u
INFO
TUN./CH
J 1 : A shortcut button cannot be registered when a DMC is used.
J 2 : Set “DMC Control” to “Disable” to automatically play back the
last song played when this unit is turned on.
En
77
PLAYBACK
Playing back tunes on the USB storage devices
SOURCE RECEIVER
You can enjoy playback of WAV (PCM format only), MP3, WMA, MPEG-4 AAC and FLAC files stored on your USB memory device or USB portable player connected
to the USB port on the front panel of this unit. This unit supports USB mass storage class devices (FAT 16 or FAT 32 format, except USB HDDs).
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
ENTER
d
• You can play back only the files stored in the first
partition.
• Some files may not be playable depending on models
and types of USB storage devices.
• For a complete list of status messages that appear on
the front panel display and GUI screen, see “USB and
Network” (☞p. 155).
• This unit is compatible with sampling frequency of up
to 48 kHz for the USB storage device.
Playback of the USB storage device
The USB storage device can be operated from the menu
displayed on the TV screen.
You can operate the contents of USB storage device
from the Now Playing view or the Browse view.
10 Pages Up
10 Pages Down
Goes to 10 pages forwards or backwards.
■ Operating from the Browse view
1 Page Up
If you have connected the USB storage device to this
unit before, playback of the music file played at the last
time automatically starts.
1 Page Down
i
Scrolls the list to the next or previous page.
a b c
RETURN
Now Playing
e
f
d
g
h
a
b
c
d
e
f
g
h
Repeat icon
Shuffle icon
Play icon
Current directory name
Menu items
Input icon
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
Current menu number / Number of all menu items
Switches the display to the Now Playing view.
1
2
3
4
Connect your USB storage device to the
USB port on the front panel (☞p. 39).
Rotate the INPUT selector (or press dUSB)
to select “USB” as the input source.
Press iCursor B / C / D / E to select a
music file to play back.
• To select a file or folder, press iCursor B / C.
• To confirm the selection, press iENTER.
• To return to the previous menu, press iRETURN.
Press iENTER to start playback.
The Now Playing view appears during playback.
Screen buttons on the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
En
78
PLAYBACK
Playing back tunes on the USB storage devices
SOURCE RECEIVER
■ Operating from the Now Playing
view
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
with the remote control
Operates the basic playback functions of USB.
AV
1
■ Operating basic playback functions
Play Control
a b c
AUDIO
e
f
d
h
i
g
s (Stop)
Stops playback.
b (Skip -)
Skips to the beginning of the currently
playing song. Press iENTER at the
beginning of the song to skip to a previous
song.
a (Skip +)
Skips to the beginning of the next song.
ENTER
PRG SELECT
h
i
Repeat icon
Shuffle icon
Play icon
Album image
Artist name
Album title
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
Song title
Elapsed time
gp
Play
gs
Stop
ga
Skip forward during playback
gb
Skip backward during playback
■ Shuffle/repeat playback
Scroll
a
i b
c
d
e
g f
g
Use the following remote control keys to operate
(playback, stop, skip, etc.) USB storage device.
Switches the scroll target (artist name, album title, or
song title).
Use the Option menu to apply playback shuffle and
repeat settings. Refer to “Shuffle playback” (☞p. 61)
and “Repeat playback” (☞p. 61) for details.
Browse
Switches the display to the Browse view.
• You can switch the information displayed on the front
panel display by pressing uINFO (☞p. 11).
• Album images are available only when the file
contains image data.
Screen buttons on the Now Playing view
CATEGORY
u
INFO
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
TUN./CH
En
79
PLAYBACK
Listening to the Internet Radio
SOURCE RECEIVER
You can listen to Internet Radio stations using the vTuner Internet Radio station database service particularly customized for this unit, providing a database of over 2000
radio stations. Also, you can store your favorite stations with bookmarks.
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
AUDIO
ENTER
RETURN
d
i
• To use this feature, your network must be connected to
the Internet.
• A narrowband Internet connection (i.e. 56K modem,
ISDN) will not provide satisfactory results, and a
broadband connection is strongly recommended (i.e. a
cable modem, an xDSL modem, etc.). For detailed
information, consult with your ISP.
• If you do not use a DHCP server, configure the
network parameters (IP address, etc.) of this unit
manually (☞p. 121).
• Some security devices (such as firewall) may block the
access of this unit to Internet Radio stations. In such
cases, configure the security settings appropriately.
• This service may be discontinued without notice.
• Some Internet Radio stations may not be played.
Listening to Internet Radio
For a complete list of status messages that appear on
the front panel display and GUI screen, see “USB and
Network” (☞p. 155).
The Internet Radio can be operated from the menu
displayed on the TV screen.
You can operate the Internet Radio from the Now
Playing view or the Browse view.
■ Operating from the Browse view
a
10 Pages Up
10 Pages Down
Goes to 10 pages forwards or backwards.
b
c
d
e
1 Page Up
1 Page Down
f
a
b
c
d
e
f
Play icon
Current directory name
Menu items
Album art / Input icon
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
Current menu number / Number of all menu items
Scrolls the list to the next or previous page.
Now Playing
Switches the display to the Now Playing view.
1
2
Screen buttons on the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
Bookmark On
3
Press dNET repeatedly to select “NET
RADIO” as the input source.
Press iCursor B / C to select an item to
play back.
• To select an item, press iCursor B / C.
• To confirm the selection, press iENTER.
• To return to the previous menu, press iRETURN.
Press iENTER to start playback.
The Now Playing view appears during playback.
The selected Internet Radio station is added to the
Bookmarks list in “NET RADIO.”
Bookmark Off
This item is displayed in the bookmark directory.
The selected Internet Radio station is removed from the
Bookmarks list.
En
80
PLAYBACK
Listening to the Internet Radio
SOURCE RECEIVER
■ Operating from the Now Playing
view
Switches the display to the Browse view.
AV
1
2
5
6
1
2
PHONO
MULTI
3
4
7
V-AUX
3
4
USB
NET
a
AUDIO
DOCK
TUNER
SIRIUS
■ Operating basic playback functions
with the remote control
Use the following remote control keys to operate
(playback, stop) the Internet Radio.
[A]
e
b
cd
a
i b
c
g d
e
ENTER
Browse
Play icon
Album image
Elapsed time
Current station name
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
You can switch the information displayed on the front
panel display by pressing uINFO (☞p. 11).
Screen buttons on the Now Playing view
gp
Play
gs
Stop
You can also register your favorite Internet Radio
stations on this unit by accessing the website with the
web browser on your PC. To use this feature, you
need the vTuner ID of this unit and your e-mail
address to create your personal account. For details,
refer to the help information on the website.
URL: http://yradio.vtuner.com/
NOTE
To clear the personal account such as vTuner ID or email address, perform “NETWORK” of
“INITIALIZE” in the Advanced Setup menu
(☞p. 141).
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
Bookmark On
The station currently being played back is added to the
Bookmarks list in “NET RADIO.”
CATEGORY
u
INFO
Play Control
TUN./CH
The following operation is available.
s (Stop)
Stops playback.
En
81
PLAYBACK
Using the Rhapsody® service
SOURCE RECEIVER
Prohibition
AV
1
2
3
4
5
6
7
V-AUX
1
2
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
It is strictly prohibited to modify, reproduce, reverse-engineer or use this unit and/or built-in software for use other than audiovisual purposes.
AUDIO
The Rhapsody® service is the power behind the Rhapsody® Media Player (the Rhapsody® player software that you can download to your computer). Rhapsody® service
d supplies the music, keeps My Library up to date, provides you with Rhapsody® channels, the Playlist Central online community, and manages your downloads. Your
software connects to Rhapsody® service through the internet. Because your account information and Rhapsody® content are on servers instead of any individual computer,
your music is infinitely portable. Much of what you see in the Display area comes from Rhapsody® service. What you can do with Rhapsody® service depends on your
subscription. You can use Rhapsody® service for free, or get even more from a paid membership. The Rhapsody® service also brings you Rhapsody® Online, a
streamlined, internet version of Rhapsody® that you can access from almost anywhere. Just sign in to your Rhapsody® account to start letting the Rhapsody® service work
for you.
h For more information, http://www.rhapsody.com/
Rhapsody® account sign-in
ON SCREEN
ENTER
i
When you select “Rhapsody” for the first time, the signin screen appears. Sign in to your Rhapsody® account to
start using the Rhapsody service on this unit.
3
Use iCursor D / E to select “Rhapsody”
and press iCursor B.
4
Press iCursor B / C to select “Sign In” and
then press iENTER.
The following display appears when “Sign In” has not
been completed yet. Read the description and then
press iENTER. J1
Use the Utility function later to view information for
your Rhapsody® account.
1
2
Press hON SCREEN.
Use iCursor B / C to select “Input” and
press iENTER.
If “Rhapsody Trial” is selected, the URL for free 30day trial service content is displayed. You can get
started with a free trial by registering an account in
the specified website.
Continues to the
next page
J 1 : When “Sign In” has not been completed yet, this description can
be directly displayed by pressing dNET repeatedly to select
“Rhapsody” as input source.
En
82
PLAYBACK
Using the Rhapsody® service
SOURCE RECEIVER
5
6
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
DOCK
MULTI
USB
NET
TUNER
SIRIUS
[A]
AUDIO
Press iENTER to enter the User Name
entry screen.
Use iCursor B / C / D / E and iENTER to
enter your user name password (up to
64 characters) and then select “OK” and
press iENTER.
7
8
Press iENTER to enter the User Password
entry screen.
Use iCursor B / C / D / E and iENTER to
enter your password (up to 64 characters)
and then select “OK” and press iENTER.
“Please wait” appears followed by the confirmation
screen.
Playback of Rhapsody® contents
The Rhapsody can be operated from the content window
on the TV screen.
You can operate the Rhapsody from the Now Playing
view or the Browse view.
■ Operating from the Browse view
a b c
NOTE
If registration failed, the error message appears. In
this case, read the message and start all over again.
ENTER
9
i
Press iENTER.
d
f
e
The Rhapsody Browse view is displayed.
To clear the characters entered in step 6 and 8, select
“CLEAR” and press iENTER.
g
a
b
c
d
e
f
g
Repeat icon
Shuffle icon
Play icon
Menu items
Album art / Input icon
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Browse view” for details.
Current menu number / Number of all menu items
En
83
PLAYBACK
Using the Rhapsody® service
SOURCE RECEIVER
■ Operating from the Now Playing
Screen buttons on the Browse view
To use these buttons, first press iCursor E. Then
select the desired one with iCursor B / C and
iENTER.
AV
1
2
5
6
3
4
7
V-AUX
1
2
3
4
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Utility
d
i
ENTER
RETURN
view
Switches the display to the Now Playing view.
a b c
You can navigate the Rhapsody menu with the following
remote control buttons.
AUDIO
PHONO
Now Playing
Play
Plays back the song or album highlighted
in the list.
Add track to My
Library
Adds the track currently selected to “My
Library.”
Add album to My
Library
Adds the album currently selected to “My
Library.”
Add CH to My
Library
Adds the channel currently selected to
“My Library.”
Remove from My
Library
Removes the content currently selected
from “My Library.”
1
2
Press dNET repeatedly to select
“Rhapsody” as the input source.
Press iCursor B / C to select an item to
play back.
• To select an item, folder or file, press iCursor B / C.
• To confirm the selection, press iENTER.
• To return to the previous menu, press iRETURN.
Rhapsody Music
Guide
Select a track from the lists organized by
category (artist, album, etc.).
Rhapsody Radio
Select a network radio channel from the
lists of the channels provided by
Rhapsody.
Search
Use the software keyboard to search the
desired item (artist, album, etc.) by
keyword.
My Library
Select a track from items (artist, album,
etc.) added to “My Library.”
10 Pages Up
10 Pages Down
Goes to 10 pages forwards or backwards.
1 Page Up
1 Page Down
Scrolls the list to the next or previous page.
3
Press iENTER to start playback.
The Now Playing view appears during playback.
e
f
d
h
k
a
b
c
d
e
f
g
h
i
j
k
g
i
j
Repeat icon
Shuffle icon
Play icon
Album image
Artist name
Album title
Screen button area
Buttons for available operations are displayed. See
“Screen buttons on the Now Playing view” for details.
Song title
Total playback time
Progress bar
Elapsed time
• You can switch the information displayed on the front
panel display by pressing uINFO (☞p. 11).
• Album images are available only when the file
contains image data.
CATEGORY
u
INFO
TUN./CH
En
84
PLAYBACK
Using the Rhapsody® service
SOURCE RECEIVER
Screen buttons on the Now Playing view
To use these buttons, first press iENTER. Then select
the desired one with iCursor B / C and iENTER.
AV
1
2
3
4
5
6
1
2
7
V-AUX
3
4
PHONO
MULTI
USB
NET
DOCK
TUNER
SIRIUS
[A]
Play Control
■ Operating basic playback functions
with the remote control
Use the following remote control keys to operate
(playback, stop, skip, etc.) your PC contents.
AUDIO
Operates the basic playback functions of PC.
i
ENTER
p (Play)
Starts playback.
s (Stop)
Stops playback.
e (Pause)
Stops playback temporarily.
b (Skip -)
Skips to the beginning of the currently
playing song. Press iENTER at the
beginning of the song to skip to a previous
song.
a (Skip +)
Skips to the beginning of the next song.
gp
Play
gs
Stop
ge
Switches between playback and pause.
ga
Skip forward during playback
gb
Skip backward during playback
■ Shuffle/repeat playback
Use the Option menu to apply playback shuffle and
repeat settings. Refer to “Shuffle playback” (☞p. 61)
and “Repeat playback” (☞p. 61) for details.
Utility
PRG SELECT
g
Add track to My
Library
Adds the track currently selected to “My
Library.”
Add album to My
Library
Adds the album currently selected to “My
Library.”
Add CH to My
Library
Adds the channel currently selected to
“My Library.”
Scroll
Switches the scroll target (artist name, album name, or
song name).
Browse
Switches the display to the Browse view.
En
85
PLAYBACK
Listening to the SIRIUS Internet Radio
Listening to the SIRIUS Internet Radio
SOURCE RECEIVER
It’s easy to enjoy SIRIUS entertainment at home. Listen to over 80 channels of commercial-free music, plus sports talk, news and entertainment. It all comes through your
audio / video receiver and high-speed Internet connection.
If you’re not a SIRIUS subscriber, you can sign up today for a PREMIUM SIRIUS Internet Radio subscription at www.sirius.com Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.4
Linearized : Yes
Encryption : Standard V2.3 (128-bit)
User Access : Print, Extract, Print high-res
Has XFA : No
XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer : Acrobat Distiller 7.0.5 (Windows)
Create Date : 2010:06:22 10:49:17Z
Creator Tool : FrameMaker 7.1
Modify Date : 2010:10:05 16:43:02+09:00
Metadata Date : 2010:10:05 16:43:02+09:00
Format : application/pdf
Title :
Creator :
Document ID : uuid:bf935165-3f60-47ab-ad51-a1137c0d6090
Instance ID : uuid:f50624e4-2bd5-493d-9b89-aed1774c32f2
Page Layout : SinglePage
Page Mode : UseOutlines
Page Count : 179
EXIF Metadata provided by EXIF.tools
.