Yamaha RXA2020_RXA3020_RXV2073_RXV3073 Firmware Update_Installation_Manual RXA2020 A3020 RXV2073 V3073 Update

User Manual: Yamaha RXA2020_RXA3020_RXV2073_RXV3073 Firmware Update_Installation_Manual

Open the PDF directly: View PDF PDF.
Page Count: 3

DownloadYamaha RXA2020_RXA3020_RXV2073_RXV3073 Firmware Update_Installation_Manual RXA2020 A3020 RXV2073 V3073 Update
Open PDF In BrowserView PDF
FIRMWARE UPDATING PROCEDURE
IMPORTANT NOTICE
Do not attempt to update your Yamaha receiver using any other data file except those provided directly from the
Yamaha website or through your network connection.
Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by
Yamaha.
Improperly updated products may cause improper operation, and any parts or service required to restore proper
operation will not be covered under the Yamaha Limited Warranty.

In case of error, see the Troubleshooting section

Requirement:

USB thumb drive, with enough free space to store over 25MB.
(File system with FAT16 or FAT32 format)
Firmware file provided by YAMAHA, “R0316-xxxx.bin”.

1 Prepare USB thumb drive for the update
Download the firmware, unzip and copy “R0316-xxxx.bin” into the root directory of the USB thumb drive.

Drag & Drop the file into USB thumb drive.

2 Power off the receiver (Standby mode)

3 Insert the USB thumb drive
USB port is located at the lower left corner of the front panel.

4 Enter the ADVANCED SETUP mode
While pressing the STRAIGHT key, press the MAIN ZONE
“ ADVANCED SETUP ” appears on the front panel display.

key and keep STRAIGHT key pressed until

1

5 Select firmware update from the menu
Press the PROGRAM key until “ FIRM UPDATE USB ” is displayed.

STRAIGHT key
MAIN ZONE

key

PROGRAM key
USB port

6 Start firmware update
a. Press INFO key to start the update.
(Update process may take up to 10 minutes)
* If “ UPDATE SUCCESS ” appears, this means your receiver is already up-to-date. In this case, power off to exit
from Advanced Setup. Your AV receiver is ready for normal use.
Firmware update in progress

Caution
DO NOT interrupt power during the update.
In case the power is accidentally cut off resulting in a condition where you can’t recover normal operation, refer to
the troubleshooting method (Troubleshooting CASE 2) on the last page.
b. When completed, “ UPDATE SUCCESS ” appears on the display.

c. Turn off the power of the receiver by pressing the MAIN ZONE

key.

INFO key
MAIN ZONE

key

USB port

7 Select “FIRM UPDATE” from the menu
a. Power on the AV receiver and press the ON SCREEN key on the remote control.
b. Select “Information” > “System”.
c. Confirm that the firmware version is updated to the latest version.
ON SCREEN key

Congratulations!
You have completed the firmware update. Your AV receiver is ready for normal use.
2

Troubleshooting
CASE 1 Error message appeared during the update
Cause:
Method:

For some reason, the receiver can’t read the firmware data.
For your solution, check the following

❏USB thumb drive is connected properly to the receiver.
❏USB thumb drive is not password protected.
(AV receiver cannot read data from a security protected USB thumb drive)

❏Make sure the USB thumb drive is inserted before the receiver is powered on for the
update.

❏The firmware data, R0316-xxxx.bin is stored in the root directory of the USB thumb drive.
❏There is no other data except the firmware data in the USB thumb drive.
❏No folders are created in the USB thumb drive.
Else, retry the update using another USB thumb drive.

CASE 2 Firmware update doesn’t start for other reasons
● Receiver doesn’t power up after the update.
● Or, error message appeared when confirming the firmware version.
Recovery method:
1. Unplug the AC power cable from wall outlet.
2. Insert the USB thumb drive which has the firmware data stored inside, into the USB port
located on the front panel.
3. Press and hold the PURE DIRECT key and keep it pressed while you plug the AC power
cable back into the wall outlet again.
“ FIRM UPDATE USB ” will appear on the front display. Then, release the PURE DIRECT
key.
4. The update will start automatically.
5. When “ UPDATE SUCCESS ” appears on the display, firmware update is completed.
Power off the receiver and remove the USB thumb drive.
6. Confirm updated firmware version.

PURE DIRECT key

USB port

3
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Instance ID                     : uuid:8d925cb8-9a94-471e-9e6e-0ec5f748c58b
Document ID                     : uuid:CDA7E719-BB93-AF92-7D15-0C9734B9BF21
History Action                  : linearized, encrypted
History Software Agent          : PDFlib PLOP 5.0 (.NET/Win64), PDFlib PLOP 5.0 (.NET/Win64)
History When                    : 2016:11:25 18:43:13+09:00, 2016:11:25 18:43:13+09:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2016:11:25 18:43:13+09:00
Create Date                     : 2013:04:04 19:37:47+09:00
Metadata Date                   : 2016:11:25 18:43:13+09:00
Format                          : application/pdf
Creator                         : Yamaha Corporation
Producer                        : Acrobat Distiller 9.5.3 (Windows)
Keywords                        : 
Page Count                      : 3
Author                          : Yamaha Corporation
EXIF Metadata provided by EXIF.tools

Navigation menu