Yamaha FIRMWARE UPDATING PROCEDURE RX A710 Update_Installation_Manual RXA710 Installation Manual
User Manual: Yamaha RX-A710 Firmware Update_Installation_Manual
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
RX-A710 FIRMWARE UPDATING PROCEDURE IMPORTANT NOTICE Do not attempt to update your Yamaha receiver using any other data file except those provided directly from the Yamaha website or through your network connection. Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by Yamaha. Improperly updated products may cause improper operation, and any parts or service required to restore proper operation will not be covered under the Yamaha Limited Warranty. Choose from the following 2 methods to update to the latest firmware. Click here for Firmware Update Through the Internet (Connection to the Internet is required) Click here for Firmware Update by USB (A USB thumb drive is required) In case of error, see the Troubleshooting section 1 RX-A710 Firmware Update Through the Internet Requirement: Internet connection Your receiver is connected to the Internet if you can receive Internet radio stations. (See owner’s manual for details) 1 Power off the receiver (Standby mode) 2 Enter the ADVANCED SETUP mode While pressing the STRAIGHT button, press the MAIN ZONE button and keep STRAIGHT button pressed until “ A D V A N C E D S E T U P ” appears on the front panel display. * “ A D V A N C E D S E T U P ” is displayed only for a few seconds. ADVANCED SETUP 3 Select “FIRM UPDATE” from the menu a. Press the PROGRAM button until “ F I R M U P D A T E U S B ” is displayed. b. Then, press STRAIGHT button until “ N E T W O R K ” is displayed. FIRM UPDATE USB FIRM UPDATE NETWORK 4 Start firmware update a. Press INFO button to start the update. (Update process may take up to 15 minutes) * If “ U P D A T E U N A V A I L ” appears, this means your receiver is already up-to-date. In this case, power off to exit from Advanced Setup. Your AV receiver is ready for normal use. Firmware update in progress NETWORK UPDATE VERIFYING... Sx-x:xx% Caution DO NOT interrupt power during the update. In case the power is accidentally cut off resulting in a condition where you can’t recover normal operation, refer to the troubleshooting method (Troubleshooting CASE 2) on the last page. b. When completed, “ U P D A T E S U C C E S S ” appears on the display. UPDATE SUCCESS c. Turn off the power of the receiver by pressing the MAIN ZONE button. MAIN ZONE button PROGRAM button 2 INFO button STRAIGHT button RX-A710 5 Check the updated firmware version a. Power on the AV receiver and press the ON SCREEN button on the remote control. b. Select “Information” > “System”. c. Confirm that the firmware version is updated to the latest version. ON SCREEN button Congratulations! You have completed the firmware update. Your AV receiver is ready for normal use. 3 RX-A710 Firmware Update by USB Requirement: USB thumb drive, with enough free space to store over 25MB. (File system with FAT16 or FAT32 format) Firmware file provided by YAMAHA,”RXA710-xxxx.bin”. 1 Prepare USB thumb drive for the update Download the firmware, unzip and copy “RXA710-xxxx.bin” into the root directory of the USB thumb drive. Drag & Drop the file into USB thumb drive. 2 Power off the receiver (Standby mode) 3 Insert the USB thumb drive USB port is located at the lower left corner of the front panel. 4 Enter the ADVANCED SETUP mode While pressing the STRAIGHT button, press the MAIN ZONE button and keep STRAIGHT button pressed until “ A D V A N C E D S E T U P ” appears on the front panel display. ADVANCED SETUP 5 Select firmware update from the menu Press the PROGRAM button until “ F I R M U P D A T E U S B ” is displayed. FIRM UPDATE USB MAIN ZONE button PROGRAM button USB port 4 STRAIGHT button RX-A710 6 Start firmware update a. Press INFO button to start the update. (Update process may take up to 15 minutes) * If “ U P D A T E U N A V A I L ” appears, this means your receiver is already up-to-date. In this case, power off to exit from Advanced Setup. Your AV receiver is ready for normal use. Firmware update in progress USB UPDATE VERIFYING... Sx-x:xx% Caution DO NOT interrupt power during the update. In case the power is accidentally cut off resulting in a condition where you can’t recover normal operation, refer to the troubleshooting method (Troubleshooting CASE 2) on the last page. b. When completed, “ U P D A T E S U C C E S S ” appears on the display. UPDATE SUCCESS c. Turn off the power of the receiver by pressing the MAIN ZONE button. MAIN ZONE button INFO button USB port 7 Check the updated firmware version a. Power on the AV receiver and press the ON SCREEN button on the remote control. b. Select “Information” > “System”. c. Confirm that the firmware version is updated to the latest version. ON SCREEN button Congratulations! You have completed the firmware update. Your AV receiver is ready for normal use. 5 RX-A710 Troubleshooting CASE 1 “UPDATE FAIL” appeared during the update Cause: For some reason, the receiver can’t read the firmware data. Method: For your solution, check the following [Update through Internet] ❏ Check Internet connection. Your Internet connection is working by playing an Internet radio station. (See owner’s manual for details) [Update by USB thumb drive] ❏ USB thumb drive is connected properly to the receiver. ❏ USB thumb drive is not password protected. (AV receiver cannot read data from a security protected USB thumb drive) ❏ Make sure the USB thumb drive is inserted before the receiver is powered on for the update. ❏ The firmware data, RXA710-xxxx.bin is stored in the root directory of the USB thumb drive. ❏ There is no other data except the firmware data in the USB thumb drive. ❏ No folders are created in the USB thumb drive. Else, retry the update by USB using another USB thumb drive. CASE 2 Firmware update doesn’t start for other reasons ● Receiver doesn’t power up after the update. ● Or, “ERROR” appeared when confirming the firmware version. Recovery method using USB method: 1. Unplug the AC power cable from wall outlet. 2. Insert the USB thumb drive which has the firmware data stored inside, into the USB port located on the front panel. 3. Press and hold the PURE DIRECT button and keep it pressed while you plug the AC power cable back into the wall outlet again. “ U S B U P D A T E ” will appear on the front display. Then, release the PURE DIRECT button. 4. The update will start automatically. 5. When “ U P D A T E S U C C E S S ” appears on the display, firmware update is completed. Power off the receiver and remove the USB thumb drive. 6. Confirm updated firmware version. USB UPDATE UPDATE SUCCESS PURE DIRECT button USB port 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Instance ID : uuid:dfd87533-fcf8-4724-8aac-78fd9efc21a4 Document ID : uuid:AB5DAE14-0C85-E904-91BB-A00FAB3F428A History Action : linearized, encrypted History Software Agent : PDFlib PLOP 5.0 (.NET/Win64), PDFlib PLOP 5.0 (.NET/Win64) History When : 2016:11:25 18:43:15+09:00, 2016:11:25 18:43:15+09:00 Producer : Acrobat Distiller 8.2.6 (Windows) Creator Tool : Adobe InDesign CS3_J (5.0.4) Modify Date : 2016:11:25 18:43:15+09:00 Create Date : 2011:06:27 07:48:40+09:00 Metadata Date : 2016:11:25 18:43:15+09:00 Format : application/pdf Title : FIRMWARE UPDATING PROCEDURE Creator : YAMAHA CORP. Description : RX-A710 Page Count : 6 Page Layout : SinglePage Subject : RX-A710 Author : YAMAHA CORP.EXIF Metadata provided by EXIF.tools