Yamaha RX V571 Easy Setup Guide
User Manual: Yamaha RX-V571 Easy Setup Guide
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
English 1 Preparation Accessories Check that the following accessories are supplied with the unit. AV Receiver Easy Setup Guide Remote control Batteries (AAA, R03, UM-4) x 2 Insert the batteries into the battery case in correct directions (+ and -). AM antenna FM antenna* NATURAL SOUND AV RECEIVER RX-V571 DIRECT YPAO MIC INFO MEMORY PRESET FM AM TUNING VOLUME SCENE BD DVD PHONES SILENT CINEMA USB INPUT TONE CONTROL iPod/iPhone TV CD PROGRAM RADIO VIDEO AUX STRAIGHT HDMI IN VIDEO L AUDIO R The Easy Setup Guide explains the general procedures for setting up the 5.1 or 7.1-channel system and how to produce surround sounds from BD/DVD. For more details, please refer to the “Owner’s Manual” contained in the CD-ROM. About the symbols in this manual. • “ • “ VIDEO AUX input YPAO microphone cover ” indicates the explanations for better use. ” indicates the cautions concerning operations or setup of the unit. A PDF format of this guide and the “Owner’s Manual” can be downloaded from the following website. http://download.yamaha.com/ CD-ROM Easy Setup Guide Safety Brochure (Owner’s Manual) (this manual) * The supplied FM antenna will differ depending on your country or region. Preparing cables Prepare the following cables (not supplied) for connection according to the instructions in this guide. Speaker cable (for each speaker) Monaural pin cable x 1 HDMI cable x 2 Digital optical cable x 1 • A digital optical cable is not required when your TV supports the Audio Return Channel (ARC) function. 2 Placing speakers Place the speakers in as shown below. Other layouts (except for 5.1-channel speaker layout and 7.1-channel speaker layout) are shown in the “Owner’s Manual.” 5.1-channel system 7.1-channel system 60° 60° 80° 80° 30 cm (1 ft.) or more 60° 60° 80° 2 80° FL Front speaker (L) FR Front speaker (R) C Center speaker SL Surround speaker (L) SR Surround speaker (R) SBL Surround back speaker (L) SBR Surround back speaker (R) SW Subwoofer 3 Connecting speakers • (U.S.A. and Canada models only) The unit is configured to 8Ω speakers as the factory setting. 6Ω speakers can be also connected. • (Except for U.S.A. and Canada models) Use the speakers with an impedance of at least 6Ω. • Use a subwoofer with a built-in amplifier. 1 Connect the front speakers ( the FRONT ( / / ) terminals. FRONT L CENTER 2 Connect the center speaker ( ) to the CENTER terminal. The unit (rear) The unit (rear) R ) to R SURROUND L R SURROUND BACK/ BI-AMP L R FRONT L CENTER R SURROUND L SURROUND BACK/ BI-AMP L R SINGLE SINGLE • Disconnect the power plug before connecting the speakers. • Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of the unit. If this happens, it may damage the unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES!” will appear on the front panel display when the unit is switched on. SPEAKERS SPEAKERS SUBWOOFER SUBWOOFER Connecting speaker cables Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colorcoded to prevent confusion, you should connect the black side to the negative terminal and the other wire to the positive terminal. 1 Remove approximately 10 mm (0.4 in.) of insulation from the end of the speaker cable and twist the bare wire firmly. 2 Loosen the speaker terminal. + (Red) FR ON T - (Black) 3 Insert the bare wire into the gap on the side of the terminal. When it is difficult to insert the wire into the gap on the side, insert it into the gap downside of terminal. 4 Tighten the terminal. Connecting banana plugs (Except U.K., Europe, Asia and Korea models) Tighten the knob, and then insert the banana plug into the end of the terminal. FR ON T Banana plug 3 3 3 Connect the surround speakers ( to the SURROUND ( / / ) terminals. FRONT L CENTER 4 Connect the subwoofer ( ) to the SUBWOOFER jack. Before connecting the subwoofer, turn off the subwoofer. The unit (rear) R ) R SURROUND L SURROUND BACK/ BI-AMP L R SINGLE The unit (rear) R FRONT L CENTER R SURROUND L For the 7.1-channel system Connect the surround back speakers ( / ) to the SURROUND BACK ( / ) terminals. SURROUND BACK/ BI-AMP L R SINGLE The unit (rear) R FRONT L CENTER R SURROUND L SURROUND BACK/ BI-AMP L R SINGLE SPEAKERS SUBWOOFER SPEAKERS SUBWOOFER SPEAKERS Use a monaural pin cable to connect the subwoofer. 4 Monaural pin cable SUBWOOFER 1 Connect external devices to the unit. 4 Connecting external devices 1 Connect a BD/DVD player to the unit with an HDMI cable. If the BD/DVD player are connected to a TV directly with an HDMI cable, disconnect the cable from the TV and connect it to the unit. TV Audio output (Digital optical) HDMI input HDMI output HDMI HDMI BD/DVD player OPTICAL HDMI O 2 Connect the TV to the unit with an HDMI cable. 3 Connect the TV to the unit with an optical cable. This connection enables the TV audio to be played through the unit. If your TV supports the Audio Return Channel function (ARC), this connection is unnecessary. HDMI VOLTAGE SELECTOR (General model only) Set the switch position of the VOLTAGE SELECTOR according to your local voltage using a straight slot screwdriver. Voltages are AC 110-120/ 220-240 V, 50/60 Hz. HDMI SURROUND BACK/ BI-AMP R L SINGLE 110V120V 220V240V HDMI VOLTAGE SELECTOR HDMI 1 SUBWOOFER HDMI OUT jack HDMI1 jack 4 Connect the power cable to an electric outlet. • (General model only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. ARC (BD/DVD) HDMI1 HDMI OUT Plug into an electric outlet ARC HDMI OUT DOCK (BD/DVD) HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5 ANTENNA COMPONENT VIDEO R FRONT CENTER L R SURROUND L SURROUND BACK/ BI-AMP R L SINGLE AM FM PR 2 Turn on the TV, BD/DVD player and the unit. 3 Confirm that the video images input from 75Ω PB VIDEO Y MONITOR OUT MONITOR OUT L R O AV4 (OPTICAL) jack OPTICAL OPTICAL OPTICAL COAXIAL COAXIAL (TV) AV 1 1 AV AV AV 2 2 AV 4 COAXIAL (CD) AV 3 OPTICAL (TV) AV 4 AV 5 AV 6 AV OUT • For connecting other devices, such as a radio antenna, refer to “SETUP” in the “Owner’s Manual.” BD/DVD player is displayed on the TV screen. SUBWOOFER SPEAKERS AUDIO The unit (rear) a Change video input source for the TV to the unit. NATURAL SOUND AV RECEIVER RX-V571 DIRECT YPAO MIC Turn on the unit INFO MEMORY PRESET FM AM TUNING VOLUME SCENE BD DVD PHONES SILENT CINEMA USB INPUT TONE CONTROL TV CD PROGRAM iPod/iPhone b Press HDMI1 to select “HDMI1” as the input source. If the video image input from BD/DVD player is displayed on the TV screen, all settings have been completed. Go to the next page, and refer to “Optimizing the speaker settings automatically (YPAO).” RADIO VIDEO AUX STRAIGHT HDMI IN VIDEO L AUDIO R The unit (front) 5 5 Optimizing the speaker settings automatically (YPAO) 1 Connect YPAO microphone to the YPAO MIC jack on the front panel. The following image is displayed on the TV screen. The YPAO microphone (supplied) detects the status of speaker connections and the distance between the speakers and the listening position, and adjusts the volume balance and the tone settings automatically (YPAO: Yamaha Parametric room Acoustic Optimizer). • The volume level is fixed to 0 dB while measuring. • The test tone is output at a high volume while measuring. Be careful that the test tone does not frighten any small children. • The room must be quiet while measuring. • Do not connect headphones to the unit. • YPAO measurement does not work correctly if any obstacles are in the room. Move everything out of the room or place it in the corners while measuring. It takes approximately three minutes to finish this measurement. CODE SET SOURCE RECEIVER HDMI 1 2 3 A AV 1 2 3 4 5 6 AUDIO DOCK USB TUNER Preparation before using YPAO FM AM INFO MEMORY MOVIE MUSIC PRESET (If necessary) Select the language displayed on the TV screen with “Language” in the “Setup” menu referring to “Owner’s Manual” (p.75). VOLUME • To cancel the measurement, disconnect the YPAO microphone before measuring starts. TUNING SUR. DECODE STRAIGHT ENHANCER SLEEP • Turn on the subwoofer and set its volume to approximately half. And, set the crossover frequency (if available) to maximum. 4 V-AUX V VAUX 5 The unit (front) 2 Confirm that “Start” is selected, and then DIRECT SCENE BD DVD TV CD SETUP OPTION SETUP VOLUME ENTER RETURN DISPLAY A TOP MENU CROSSOVER/ HIGH CUT RADIO POP-UP MENU Cursor keys ENTER RETURN press SETUP. The measurement starts in ten seconds. After the measurement is complete, the following image is displayed on the TV screen. MUTE MODE MIN MAX MIN MAX • When a subwoofer with the automatic standby function (turn off automatically during no signals input) is used, disable the function before going to the next step. YPAO microphone listening position 2 3 5 6 7 9 0 10 4 8 ENT TV INPUT TV VOL TV CH MUTE The height of your ears Set the YPAO microphone at the height of your ears. We recommend that you use equipment that allows you to adjust the height (such as a tripod) as a microphone stand. If you are using a tripod, use the tripod screws to fix the microphone in place. 6 1 • When “W-1:Out of Phase” appears, refer to ‘When “W-1: Out of Phase” appears’ on the next page. • If a message such as an error message and warning appears, refer to “Error messages” and “Warning messages” in the “Owner’s Manual.” 3 Confirm that “Save / Exit” is selected, and then press ENTER. When “W-1: Out of Phase” appears Use the following procedure to check the speaker connections. Warning messages may appear depending on the types of speakers or the place where you set them even if they are connected correctly. 4 Confirm that “SAVE” is selected, and then press ENTER. a Press the cursor key to select “Result,” and then press ENTER. b Confirm that “Wiring” is selected. c Check the cable connection (+ and -) of the speaker indicated as red-boxed “Reverse.” If the speakers are connected correctly: Save the results of the measurement. Press RETURN, and go to step 3 on the left column. 5 Remove the YPAO microphone from the If the speakers are connected incorrectly: Turn off the unit and connect the speaker cables again, and then try YPAO measurement again. unit. All the settings for the speakers are complete. • The YPAO microphone is sensitive to heat. Protect the YPAO microphone from high temperatures (such as from AV equipment) and direct sunlight. 7 6 Playing back a BD/DVD More various features! More various functions are available with the unit. Let’s play a BD/DVD disc. We recommend playing back a disc recorded with multi-channel sound (at least 5.1ch) to enjoy the surround sound effects enough. 1 Press HDMI1 to select “HDMI1” as the input source. CODE SET SOURCE RECEIVER Refer to the “Owner’s Manual” for details on effective use of the unit. Connecting external devices other than BD/DVD players (p.23) VOL. HDMI 1 2 3 4 HDMI1 V-AUX V VAUX 5 2 3 4 5 6 AUDIO DOCK USB TUNER FM AM INFO MEMORY MOVIE MUSIC PRESET ENHANCER BD DVD R SR VOL. TUNING Volume -30.0dB SUR. DECODE STRAIGHT SLEEP L SL 2 Play a BD/DVD with a BD/DVD player. 3 Press VOLUME to adjust the volume. A AV 1 HDMI1 SW C DIRECT L SL SW C R SR The 5.1 or 7.1-channel system is installed and the procedures to play a BD/DVD are complete. RADIO Various devices, audio players, such as CD players, video games, camcorders, etc. can be connected to the unit. Selecting the favorite sound programs (p.36) You can select various sound programs (CINEMA DSP) and sound decoders in many different categories suitable for movies, music, video games, sports programs, and so on. SETUP VOLUME RETURN TOP MENU POP-UP MUTE MODE 1 2 3 4 5 6 7 8 9 0 10 ENT VOLUME • “STRAIGHT” is set to the sound program as the initial settings. “STRAIGHT” (straight decoding) is the sound program which output recorded sound from each channel directly from each speaker. Therefore, surround back speakers have no sound when 5.1-channels are played back on a 7.1-channel system. When no sound is output from surround speakers TV INPUT TV VOL MUTE TV CH Sound is only output from front speakers even when playing multi-channel source Confirm the digital audio output settings of the BD/DVD player. Signals may be set to normally output on 2 channels (such as PCM). No sound is output from a specific speaker Playing songs with your iPod (p.46) You can play an iPod with the unit using a USB cable supplied with the iPod, the Yamaha iPod universal dock (optional) or an iPod wireless system (optional). z Listening to FM/AM (p.41) z Playing back songs with Bluetooth devices (p.53) z Playing back songs with USB storage devices (p.55) z Changing input settings with a single key (SCENE function) (p.35) For more detail, see “What you can do with the unit” (p.5). Refer to “Troubleshooting” in the “Owner’s Manual.” © 2011 Yamaha Corporation YD340C0/ESEN
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Page Mode : UseOutlines XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : FrameMaker 7.1 Modify Date : 2011:03:24 14:01:22-07:00 Create Date : 2010:12:18 17:22:39Z Metadata Date : 2011:03:24 14:01:22-07:00 Format : application/pdf Title : Creator : . Document ID : uuid:9cfc1dc4-cc3c-4b86-ab52-43d94c244419 Instance ID : uuid:56e01627-a8d3-4000-b5eb-ff2e640a0fc9 Page Count : 8 Page Layout : SinglePageEXIF Metadata provided by EXIF.tools