Yamaha YAS 108/ATS 1080 Firmware Update Installation Manual YAS108_ATS1080 YAS108 ATS1080
User Manual: Yamaha YAS108_ATS1080 Firmware Update Installation Manual
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
EN Manual Development Group © 2018 Yamaha Corporation Published 05/2020 YJOD-C0 AV17-0324 Update Guide Equipment required for firmware update This Guide provides instructions for updating firmware with a USB flash drive on the following products. • YAS-108 • ATS-1080* * Sold only in certain countries or regions Prepare the following items before attempting to update firmware. • USB flash drive Use a USB flash drive that meets all of the following requirements. – Supports the USB mass storage device class – Formatted in FAT16 or FAT32 format – No encryption applied – No data stored on the device (empty) See product pages on the Yamaha website for details regarding the issues resolved, and functions added, by updating firmware. • Computer that can be connected to the Internet Download the firmware from the Yamaha website. 1 Preparing the firmware 1 2 Download the latest version of firmware from the Yamaha website to a computer. See product pages on the Yamaha website for more information. Decompress the downloaded file and save the firmware data file to the USB flash drive. The compressed file contains multiple data files (.108.) Be sure to save all firmware data files in the top folder (root folder) of the USB flash drive. Do not change the file name when saving them. 2 Checking the current firmware version 2 Depending on the current firmware version of your unit, the procedure of the firmware update differs. Before the update, check the current firmware version. 1 Tap “INFORMATION” and then check “System Version”. Access to the unit with the Home Theater Controller app. System Version Version 6.xx: See “Procedure for the version 6.xx units” on page 4. Other versions: See “Procedure for other units” on page 5. 3 Updating the unit’s firmware 3 Procedure for the version 6.xx units 1 Turn off the unit. 2 Connect the USB flash drive to the UPDATE ONLY jack on the unit. Touch and hold least 5 seconds. and together for at The firmware update begins. During the update, all indicators will turn off. Wait for 5 minutes or more without any operation. YAS-108 ATS-1080 4 After 5 minutes or more, touch twice. If the firmware update is completed successfully, the unit will turn on. Refer to “Checking the current firmware version” on page 3 to confirm the updated version. USB flash drive containing the firmware data file * Remove the cover. 5 Disconnect the USB flash drive. NOTICE Do not unplug the power cable or disconnect the USB flash drive until the following procedures are completed. The firmware update has been completed. 4 3 Procedure for other units 1 Turn off the unit. 2 Connect the USB flash drive to the UPDATE ONLY jack on the unit. Touch and hold least 5 seconds. and together for at The firmware update begins. The indicators will glow as shown below while the firmware is being updated. YAS-108 ATS-1080 Running display (glow in succession) Glows The indicators will flash as shown below when the firmware update has been successfully completed. USB flash drive containing the firmware data file * Remove the cover. NOTICE Flash Do not unplug the power cable or disconnect the USB flash drive until the following procedures are completed. If indicators flash differently than shown above, or fail to glow or flash at all, see “Troubleshooting” (p. 8 and 9). 4 Touch when the firmware update is complete. The unit will turn off. 5 5 Disconnect the USB flash drive. The firmware update has been completed. Refer to “Checking the current firmware version” on page 3 to confirm the updated version. 6 Troubleshooting If the firmware update fails, the indicators will flash as illustrated below. Confirm the problem and try updating the firmware again. Flashing (red) indicator Flashes (red) Cause Remedy Cause Remedy The USB flash drive is not connected to the unit correctly. 1. Terminate the update by touching z. 2. Connect the USB flash drive to the unit correctly. 3. Try updating the firmware again. The firmware data file was not properly saved to the USB flash drive. 1. Terminate the update by touching z. 2. Disconnect the USB flash drive and be sure that the firmware data files have been saved as follows. • Each file name has not been changed. • All files are stored in the top folder (root folder). 3. Connect the USB flash drive and try updating the firmware again. 7 Cause Indicators off Remedy The USB flash drive was disconnected from the unit while firmware was being updated. 1. Terminate the update by touching z. 2. Connect the USB flash drive to the unit correctly. 3. Try updating the firmware again. The USB flash drive is damaged. 1. Terminate the update by touching z. 2. Save the firmware data file to another USB flash drive and try updating the firmware again. The power cable was unplugged while firmware was being updated. There is a problem with the firmware data file. 1. Terminate the update by touching z. 2. Download the firmware data file for your unit from the Yamaha website and save it to the USB flash drive. 3. Try updating the firmware again. 1. Plug the power cable into an AC wall outlet. 2. Be sure that the USB flash drive is correctly connected to the unit. 3. Touch z. The firmware update will resume. A power failure occurred. 1. Be sure that the USB flash drive is correctly connected to the unit. 2. Touch z. The firmware update will resume. Turned off Cause 8 Remedy
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Copy, Extract, Print high-res Language : en XMP Toolkit : Adobe XMP Core 5.6-c016 91.163616, 2018/10/29-16:58:49 Instance ID : uuid:6dc1901d-aab3-4d28-8ef0-3eed1397d2ab Document ID : uuid:5615E7D8-4715-FEC8-7CB8-097677659081 Producer : Acrobat Distiller 20.0 (Windows) Creator Tool : FrameMaker 2017.0.4 Modify Date : 2020:05:13 08:39:43+09:00 Create Date : 2017:06:26 10:43:10Z Metadata Date : 2020:05:13 08:39:43+09:00 Format : application/pdf Title : YAS-108/ATS-1080 Firmware Update Installation Manual Creator : Yamaha Corporation History Action : linearized, encrypted History Software Agent : PDFlib PLOP 5.0 (.NET/Win64), PDFlib PLOP 5.0 (.NET/Win64) History When : 2020:05:13 08:39:43+09:00, 2020:05:13 08:39:43+09:00 Page Mode : UseOutlines Page Count : 8 Author : Yamaha CorporationEXIF Metadata provided by EXIF.tools