Yamaha DTXPRESS IV Standard Set Assembly Manual Dtxp4std En Am A0

User Manual: Yamaha DTXPRESS IV Standard Set Assembly Manual

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadYamaha DTXPRESS IV Standard Set Assembly Manual Dtxp4std En Am A0
Open PDF In BrowserView PDF
CAUTION

If this symbol is ignored and the equipment is used
improperly, there is a danger or injury to persons handling
the equipment, and material damage could occur.

Figure 4: Rack Assembly-2

Figure 6: Rack Assembly-4

Watch your fingers when adjusting clamps. They may become pinched, resulting in
injury.

Standard Set V2 Assembly Manual

M

Make sure you hold onto the plug, not the cable, when connecting or disconnecting
the cable. Also, never place any heavy or sharp objects on the cable. Applying
excessive force to the cable may result in damage to the cable, such as the wires being
severed, etc.

This manual describes the regular assembly of the DTXPRESS IV Standard Set V2.
After assembling the parts and connecting the cords as shown in Figure 1, the
unit is ready to be turned on.
* To assemble the unit, make sure you have the following three packages:

B

Do not step on or place heavy objects on the product. It may result in damage.

- RS70 (Rack System)
- DTP4K2STD (Pad Set)
- DTXP4 (Trigger Module)

Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may
injure your fingers.

Before assembling the unit, lay a drum mat (sold separately).
Before assembling the unit, lay a drum mat on the floor. Alternately, to prevent
damaging your floor, lay the cardboard of the included packages, etc. on the
floor before assembling the two parts shown in the circles in Figure 1.

Do not put your hands or feet under the foot pedal or foot switch. They may be
pinched, resulting in injury.
Do not use or keep the product in places with extremely high temperature (places in
direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom,
outside on a rainy day, etc.). Doing so may result in deformation, discoloration,
damage or deterioration.

Figure 1: Unit Regular Assembly

When cleaning the product, do not use benzine, thinner or alcohol as it may result in
discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has
been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent
on a cloth then wipe with a damp cloth that has been wrung out thoroughly to
remove any remaining detergent. Also pay close attention so as not to let the water
and detergent come into contact with the cushions used in the product; doing so
may result in deterioration.

A
3

See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90
degrees from the pipe with the YAMAHA logo. Tighten the two knobs loosened in step 2
and fix the position of pipe .
4 See Figure 3 again. Loosen the two knobs (d) and (e) on your right.
5 See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction
until it is parallel with pipe . Tighten the two knobs loosened in step 4 and fix the position
of pipe .
* In the following steps, loosen the knobs first, decide the position of the pipe, and then
tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed.

Figure 5: Rack Assembly-3

Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged
and drums may drop, causing injury.

K

Checking the contents of RS70

J

C

D

Open the RS70 (Rack System) package and confirm the contents.
Figure 2: RS70 (Rack System)

F

Cable Band (10) *1

RS70 (1)
DTXP4 (Drum Trigger Module)
TP65S (3-zone Drum Pad)
AC Adaptor
HH65 (Hi-Hat Controller)
PCY135 (3-zone Cymbal Pad)
TP65 (Drum Pad)
KP65 (Kick Pad)
RS70 (Rack System)

If this symbol is ignored and the equipment is used
improperly, fatal injury to persons or serious damage could
occur.

Do not let small children assemble or set up this product by themselves, or they may
be injured. Always assemble this product with adult supervision.
Be careful with the edges of the cymbal holders and the tom holders. The sharp holder
ends may result in injury.

Open the DTP4K2STD (Pad Set) and Trigger Module package and confirm the
contents.
Figure 7: Pad Set DTP4K2STD
TP65 (Drum Pad) (3)

TP65S (3-zone Drum Pad) (2)

E
Assembly Manual (1) *2
- RS70

PRECAUTIONS

WARNING

12

and set up the upper part of
the cymbal holder. Tighten the wing bolt loosened and fix the position of the cymbal holder
. Set up the upper part of the cymbal holders
in the same manner.
Loosen the two knobs (p) aligned along the pipe with the Trigger Module attachment part
.
so the operating panel will face upward
Adjust the Trigger Module attachment part
firmly and
diagonally to your side when set. Hold the Trigger Module attachment part
turn it gradually. Tighten the two knobs loosened and fix the position of the Trigger Module
attachment part .

Connecting to a power source”. (Spare bands are included.)

Assembling the Rack System
1

Take out the rack system from the package and remove all the cushioning. Remove the
bubble wrap on the pipes while assembling the rack system.

The pipe ends may injure your fingers.
Figure 3: Rack Assembly-1

TP65S has a grooved rim.

PCY135 (Cymbal Pad) (2)

6

8
*1 Use cable bands to bind cables to pipes in “
*2 Not this manual.

9

Felt (Large) (2)
See Figure 5. Loosen the two knobs ((f) on the upper left) aligned at the base of pipe
, and move pipe
slightly outward in a clockwise direction. Tighten the two knobs
loosened and fix the position of pipe .
Loosen the two knobs ((g) on the middle right) aligned at the base of pipe . Move pipe
in a counterclockwise direction until it is about 90 degrees from the pipe with the
YAMAHA logo. Tighten the two knobs loosened and fix the position of pipe .
Loosen the knobs (h) and (j) (shown with on the opposite side of pipe ) of the cymbal
and
on the right and left and pull up the cymbal holders vertically to the
holders
height illustrated. Tighten the knobs loosened and fix the positions of the cymbal holders.
Loosen the two knobs ((k) on the middle left) aligned at the base of pipe
and the knob
all the way
((m) on the lower left) on the slim pipe supporting pipe . Move pipe
in a counterclockwise direction until it is about 90 degrees from
around the vertical pipe
the pipe with the YAMAHA logo. Tighten the three knobs loosened and fix the position of
and the slim pipe supporting it.
pipe

HH65 (Hi-Hat Controller) (1)

KP65 (Kick Pad) (1)

Stopper (2)

Drum Key (1)

Be sure to move pipe in a counterclockwise direction. If you move it in
a clockwise direction, the slim pipes may collide and bend.

10 Check that the entire rack system is stable. Hold the upper area of the vertical pipe

and
, and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2
to 5.

9-channel snake cable (1)

Instruction Manual (4)
- TP65/65S/100/120SD
- PCY65/65S/135/155
- HH65
- KP65

Be careful with the edges of the spurs attached to the base. The sharp spur ends may
result in injury.
If this product is used with the rack system or a cymbal stand, make sure all bolts are
tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen
the bolts. Loose bolts may result in the rack overturning or parts dropping, causing
injury.

Clamp Bolt (5)

G

7

Before using, please read this assembly manual, and use this product in a safe
and proper manner. Particularly in the case of children and young users, parents
or an instructor should teach the children the proper manner in which to use the
device.

11 See Figure 6. Loosen the wing bolt (n) of the cymbal holder

Checking the contents of the Pad Set and the
Trigger Module

L

H

q
w
e
r
t
y
u
i

L

K

Figure 8: Trigger Module

Always set the product on a flat and solid surface. Placement on a sloping, unstable
surface or on steps may result in the product being unstable and subject to
overturning.

DTXP4 (1)

Wing Bolt (2)

AC Adaptor (1)

Module Stand (1)

When setting the product, please pay close attention to the handling and setting of
cables. Carelessly placed cables may cause the user and others to trip and fall.
Do not alter the product. Doing so may result in injury or damage/deterioration to the
product.
Do not sit or step on the rack. The rack may overturn or be damaged, resulting in
injury.

* YAMAHA logo printed on pipe

2

is facing the opposite side.

See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe
facing the
opposite side from you. Support the rack system with your right hand, and loosen the two
knobs (b) and (c) on your left.

Continued on the next page (on the back side)

DTXPRESS_ST-set_en_0407.indd 1

2009/04/15 16:27:44

Mounting the pads and the trigger module on the
rack system

Figure 15: Cymbal holder-2

Figure 16: Cymbal holder-3

Installing the HH65 (Hi-Hat controller) and KP65 (Kick pad)
Figure 22: HH65 and KP65

Mount the pads and the trigger module on the rack system. Then position the
kick pad and the hi-hat.

Mounting the TP65/65S (Drum pads) on the rack system
Figure 9: Pads Assembly-1

Figure 10: TP65/65S

1
@4 Stopper
@5 Drum key
@6 Key bolt

2
3
4
!1 TP65S
!2 TP65/65S (Rear side)
!3 Clamp bolt

1

2

Figure 17: Cymbal holder and Cymbal pad

5

Q

See Figure 17. Insert the end of the L-shaped part of the stopper into the oval-shaped hole
on the cymbal pad (shown with ) to set the cymbal pad on the cymbal holder.
Attach the included round-shaped felt with a large hole-diameter to the cymbal holder,
then attach the wing nut removed in step 1 and tighten it. Turn the wing nut until you are
certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit
the surface, even when the wing nut is tightened securely.

Mounting the DTXP4 (Trigger module)
Figure 18: Pads Assembly-4

T
E

2
3

* A foot pedal (sold separately) is necessary to use the kick pad.

^1 Power supply jack (DC IN 12V)
^2 Cable clip
^1 Power switch

1

Make sure to turn the power off (the Standby/
On switch (^3) is set to the standby position
( )).

Figure 27: Cable clip (DTXP4 rear panel)

2

Connect the output jacks of the pad and the input jacks of the trigger module
with the 9-channel snake cable.
Figure 23: DTXP4 (Rear panel)

6

P

%1 TP65S
%2 HH65
%3 KP65

Connect the AC adaptor to the DTXP4.
Figure 26: Power switch (DTXP4 rear panel)

Connecting the pads to the Trigger Module

See Figure 10.
Attach the clamp bolts (!3) on TP65/65Ss (!2). Tighten the clamp bolts five to six turns each.

Figure 11: Pads Assembly-2

3

See Figure 15. Attach the stopper to the cymbal holder, and fix at a position where the
L-shaped part of the stopper is on the opposite side from you. To fix the position of the
stopper (@4), use the drum key (@5) and tighten the key bolt (@6) firmly.
See Figure 16. Attach the black plastic part removed in step 1 to the cymbal holder, and
tighten it in a clockwise direction.
Attach one of the felt washers removed in step 1 to the cymbal holder. The other felt washer
will not be used within the regular assembly described in this manual.

If a drum mat (sold separately) is not available, lay
a cardboard on the floor to prevent scratching the
surface.
Place the HH65 (Hi-Hat controllER) (%2) under the
TP65S (pad for Hi-Hat cymbal) (%1).
Place the KP65 (Kick pad) (%3) at the bottom center of
the rack system.

Connecting to a power source

Attach the AC adaptor to connect to a power
source.
Insert the DC plug into the power supply jack
(^1) and twist the cable around the cable clip
(^2) to prevent the DC plug from falling out.

Figure 28: Using Cable Band

3
Figure 24: 9-channel Snake Cable

Use the cable bands to bind the cables to the
pipes at the six points marked with circles.

* Leaving the cable slacked may interfere with your performance.

Figure 19: Module stand

R
S

See Figure 11. Loosen the knobs of the tom holders
and
at the center of the rack
system (shown with ). Move the tom holders as shown in Figure 11-(a). Then tighten the
and .
knobs and fix the position of the tom holders
Loosen the knob of the tom holder
on the right (shown with ). Move the tom holder
inward as shown in Figure 11-(b). Tighten the knobs and attach the tom holder firmly at a
position where it points slightly downward.

#1 Wing nut
#2 Module stand
#3 DTXP4 (Rear side)

1

* Each straight plug is labeled indicating the input jacks to which they are to be connected.

1
Attach the module stand (#2) onto the rear side of the DTXP4 (#3) using the wing nuts (#1).

Figure 20: Module stand and clamp

Insert the straight plugs (Figure 24-(a)) of the 9-channel snake cable into the input jacks on
the rear panel of the trigger module. For regular assembly, connect the straight plugs to the
input jacks in accordance with the indication on each label.

The assembly is now completed.
* To check the actual sound, connect the unit with an amplified speaker or a headphone before turning on the
power.

Figure 25: Diagram of standard connection

Figure 12: Tom Holder and Drum Pad

4
5
6
7

!4 Tom holder
!5 Clamp bolt
Attach the TP65 (Drum pad) to the tom holder
as shown in Figure 12. Tighten the clamp
bolt and fix the position.
See Figure 11 again. Repeat step 3 and 4 in the same manner for tom holder
at the
on the right, and attach the TP65 (Drum
center of the rack system and for tom holder
pad) to each tom holder.
Loosen the knobs of the tom holder
on the left (shown with ). Move the tom holder
inward as shown in Figure 11-(c) until it is pointing slightly downward than pipe .
Attach the 3-zone drum pad TP65S to the tom holder
set down in step 6. Tighten the
(right near
clamp bolt and attach the TP65S firmly. Attach the TP65S to the tom holder
until it is pointing slightly
the tom holder ) in the same manner. Move the tom holder
outward than pipe .

#4 DTXP4 + Module stand
#5 Clamp
#6 Knob

2

Attach the module stand (#4) onto the clamp (#5). Tighten the knob (#6) and fix the
position.

Assembling the KP65 (Kick pad)
1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent
scratching the surface.

Figure 21: KP65 Assembly

Mounting the PCY135 (Cymbal pads) on the rack system
Figure 13: Pads Assembly-3

Figure 14: Cymbal holder-1

@1 Cymbal holder
@2 Wing nut
@3 Felt washer

1

See Figure 14.
Remove the wing nut (@2) and the two felt washers (@3) from the cymbal holder (@1). Then
turn the black plastic part in a counterclockwise direction and remove it.

$1
$2
$3
$4
$5

2

Remove the wing bolt ($3), the spring washer ($4) and the washer ($5) from the body ($1),
and keep the four sets nearby in the order removed.
* If the wing bolt, the spring washer and/or the washer are separated from each other, set
them as illustrated in Figure 21-(a).

3

DTXPRESS_ST-set_en_0407.indd 2

Body
Base
Wing bolt
Spring washer
Washer

Set the base ($2) on the body ($1), and attach them using the wing bolt, the spring washer
and the washer removed in step 2.

2

Insert the L-shaped plugs (Figure 24-(b)) of the 9-channel snake cable into each
corresponding pad. It is recommended to connect the cables in order from numbers q to
o shown in Figure 25 (from the shortest cable to the longest cable).

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©2009 Yamaha Corporation
WS41320 ********.*-****
Printed in Indonesia

2009/04/15 16:27:47



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
XMP Toolkit                     : 3.1-702
Format                          : application/pdf
Creator                         : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
Title                           : DTXPRESS IV Standard Set Assembly Manual
Description                     : dtxp4std_en_am_a0.pdf
Create Date                     : 2009:04:15 16:29:42+09:00
Creator Tool                    : Adobe InDesign CS4_J (6.0)
Modify Date                     : 2009:11:27 13:21:13+09:00
Metadata Date                   : 2009:11:27 13:21:13+09:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:242b7f58-3b8b-4bed-ba6b-1329b3a2a9ca
Instance ID                     : uuid:b7dddadf-26ff-47e7-bd3e-6e5ee5dc92da
Page Count                      : 2
Page Layout                     : SinglePage
Subject                         : dtxp4std_en_am_a0.pdf
Author                          : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
EXIF Metadata provided by EXIF.tools

Navigation menu