Yamaha RS150 Assembly Instructions En
Yamaha Corporation RS150 Assembly Instructions rs150_en Yamaha Corporation - RS150 - Assembly Instructions
Yamaha Corporation RS150 Assembly Instructions rs150_en Yamaha Corporation - RS150 - Assembly Instructions
User Manual: Yamaha RS150 Assembly Instructions
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
■ Handling Precautions RS150 • Do not alter the product. Doing so may result in damage or deterioration to the product. • Do not step on or place heavy objects on the product. It may result in damage. • Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation, discoloration, stickiness, damage or deterioration. • To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product, it may result in deterioration. ASSEMBLY INSTRUCTIONS INTRODUCTION Thank you for purchasing the Yamaha Electronic Drum Rack System RS150. ■ Inside This Package Before using, thoroughly read these assembly instructions, and use this product safely and correctly. Before setup, please make sure that all of the items listed below are present and accounted for. If anything is missing, please contact the dealer from whom you purchased the unit. PRECAUTIONS Before using, please read this “Assembly Instruction” sheet, and use this product in a safe and proper manner. Especially for children, parents or an instructor should teach the children the proper manner in which to use the device. To prevent against accidents and injury * Before assembling the rack stand, make sure all of the parts shown below are included. Please follow the cautions listed below ◆Piller（C） ◆Piller（L） Acts indicated with this icon are prohibited and should not be attempted. WARNING ◆Piller（R） ◆Center Pipe（A） Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. Holder Clamp Leg Connector ◆Center Pipe（B） If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the instrument being unstable and overturning. Holder Clamp Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury. ◆Center Pipe（C） When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or causing injury to hands or fingers. ◆Cross Pipe ◆Module Holder Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury. Please be careful when children are close to or touching the product. The product has many pipes and arms so careless movement around the product may result in injury. ◆Center Pipe（D） When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may become entangled in the cables resulting in falls. CAUTION ◆Tom Clamp CL-940A（x4） If this symbol is ignored and the equipment is used improperly, there is a danger of injury to persons handling the equipment, and material damage could occur. ◆Cymbal Holder CH745 Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury. ◆ Cymbal Holder CH740（x2） ◆Small Screws M5 x 8 Watch your fingers when adjusting clamps. They may become pinched resulting in injury. ◆Cable Band（x10） （Module Holder Fixing Screws x4） Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. ◆Assembly Instructions Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. （this sheet） * Specifications are subject to change without notice. ■ RS150 Assembly * Parts for the RS150's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly. A Phillips (+) screwdriver is required when attaching the DTXTREME IIS. Please prepare one before starting assembly. 1 After removing the unit from the box, remove all cushion material. 2 Setting up the parts Follow the setup order (q~o) in the diagrams shown below. q Temporarily remove the leg connector from pillar (R). w Attach center pipe (D) to pillar (R) and pillar (C), and secure. e Reattach the leg connector. y u i o r Attach the cross pipe to the leg connector. Attach center pipe (B) to pillar (R) and pillar (C), and secure. Attach center pipe (A) to pillar (L) and pillar (C), and secure. Attach the module holder to pillar (L), and secure. Attach the cymbal holders and tom clamps to the holder clamps, and secure. t Attach center pipe (C) to pillar (L) and pillar (C), and secure. Caution : Make sure the bolts marked with a " Piller (L) Cymbal Holder (CH740) Tom Clamp (CL-940A) " are loosened before setting up. Cymbal Holder (CH740) Center Pipe (A) i Piller (C) Holder Clamp o Holder Clamp Cymbal Holder (CH745) Tom Clamp (CL-940A) o Holder Clamp o Center Pipe (B) Piller (R) u Module Holder Holder Clamp t $ Caution Tom Clamp (CL-940A) o o Leg Connector y q Remove temporarily. e Tighten knob of Center Pipe (C) Holder Clamp leg connector w Leg (L) Leg (C) Center Pipe (D) Holder Clamp r Cross Pipe Memory Clamps Using the memory clamps let you obtain the same height setting for all future setups. Leg (R) Leg Connector o ■ Optional Parts ■ Set up example ● Pad and Drum Trigger Grouping q DTXTREME IIS Drum Trigger Module w PCY130/130S Cymbal Pad r RHH130 Real Hi-hat Pad e PCY150S Cymbal Pad Satellite Speaker PCY130S Satellite Speaker w PCY150S e w PCY130 q t TP100 Drum Pad y TP120SD Drum Pad o Snare Stand !0 Hi-hat Stand *SS652 etc. *HS-740 etc. t t u KP65 i Foot Pedal Kick Pad u * DFP-9310 etc. y r ● Monitor System and Attachement Grouping • TPCL150 • CYAT150 • SPAT1 (1 set L/R units) • MS100DR • Sub Woofer amp unit • MS50DR • Sub Woofer • Satellite Speakers amp unit 3 Sub Woofer amp unit • Satellite Speakers Attaching the DTXTREME IIS 3-1 4 Attaching the cymbal pads Attach the cymbal pads to the cymbal holders and adjust their position, then secure in place. (Please refer to the Owner's Manual that came with the cymbal pads on attaching the cymbal pads.) Remove the module holder from the holder clamp, and use the supplied screws to attach the DTXTREME IIS. Make sure only the supplied screws are used. Using any other screws may result in the unit falling off the holder or damage. 5 3-2 i o !0 Slide the module holder, with the DTXTREME IIS already attached, into the holder clamp. Attaching the drum pads Attach the drum pads to the tom clamp and adjust their position, then secure in place. Step 4 DTXTREME IIS Step 3 Felt Module Holder Step 3-2 Step 3-1 Step 5 Cymbal Pad (PCY130/130S/150S) Drum Pad Holder Clamp Maker sure all bolts on clamps, pads, etc., are tightened firmly. However, loose or over-tightened bolts may result in the part falling off and/or damage. Please use caution. After assembly is complete, setup the kick pad, real hi-hat pad, etc., and connect the cables. Use the supplied cable bands to secure the cables to the frame pipes to keep cables out of the way during performance. If the rack is moved even after setup is complete, make sure the bolts are loosened before moving the rack. Anti-swivel brace (supplied with the (PCY130/130S/150S) Printed in Indonesia WG24090
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res Create Date : 2005:07:07 01:50:55Z Modify Date : 2005:07:07 16:36:17+09:00 Page Count : 2 Creation Date : 2005:07:07 01:50:55Z Mod Date : 2005:07:07 16:36:17+09:00 Producer : Acrobat Distiller 5.0.5 for Macintosh Metadata Date : 2005:07:07 16:36:17+09:00 Has XFA : NoEXIF Metadata provided by EXIF.tools