Yamaha RS 80 Owner's Manual Rs80 En
Yamaha Corporation RS-80 Owner's Manual rs80_en Yamaha Corporation - RS-80 - Owner's Manual
Yamaha Corporation RS-80 Owner's Manual rs80_en Yamaha Corporation - RS-80 - Owner's Manual
User Manual: Yamaha RS-80 Owner's Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Electronic Drum Rack System RS-80 Assembly Instructions Thank you for purchasing the Yamaha Electronic Drum Rack System RS-80. Before using, thoroughly read this assembly manual, and use this product safely and correctly. ■ RS-80 Rack Stand Parts ■ RS-80 + Pad grouping : Set up example * Before assembling the rack stand, make sure all of the parts shown below are included. A Left Side Assembly (x1) w e e q B Right Side Arm (x1) K C Right Side Assembly (x1) K F D w G H w I I w H E H J H r J H B D Center Pipe Assembly (x1) I Drum Pad Clamp (Short) (x2) t y A J E Center Bar (x1) C Drum Pad Clamp (Long) (x3) ● Pad and Drum Trigger Grouping (option) F Module Holder (x1) K Cymbal Holder (x2) L Cable Band (x10) q DTX Drum Trigger Module w TP80S/TP80 Drum Pad e PCY80S/PCY80 Cymbal Pad r KP80 Kick Pad t HH80 Hi-hat Control Pedal y Foot Pedal * FP-820 etc. (4 screws included) G H Module Holder Clamp (x1) M Tuning Key (x1) N Assembly Instructions (this sheet) Hex Rod Cylinder (x6) * Specifications are subject to change without notice. Printed in Taiwan ■ RS-80 Assembly * A screw driver (+ or -) is necessary to complete the assembly. Over-tightening of the fixing bolts may result in damage. Take care when tightening fixing bolts and screws. 1 Insert the Right Side Assembly C pipe into the Right Side Arm B , and tighten the fixing bolts. 2 Insert the Left Side Assembly A pipe and the Right Side Assembly C pipe into the Center Bar E , and tighten the fixing bolts. Make sure that the Left and Right Side Assemblies are not reversed. 3 Above the Center Bar E , attach the Center Pipe D , and tighten the fixing bolts. Attach the Center Pipe D 5 Attach the Drum Pad Clamps 5-1 Insert the Hex Rod Cylinders H into the Drum Pad Clamps I J , and tighten the fixing bolts. 5-2 Attach the Drum Pad Clamps (Short) I to the snare drum and floor tom positions. The Drum Pad Clams (Long) J should be attached to the hihat and tom tom positions. 5-3 Insert the Hex Rod Cylinders H in the pads, adjust the position of the pad and tighten the fixing bolts. Tighten Tighten Tighten Center Bar Step 3 Step 2 Tighten E Step Right Side Arm 1 6 Attach the Cymbal Holders 6-1 Insert the Cymbal Holders K into the Cymbal Holder Clamps that are attach to the left and right sides of the Center Pipe D , and tighten all fixing bolts. 6-2 Attach the Cymbal Pad to the Cymbal Holders K , adjust the position and tighten the fixing bolts. (Refer to the Cymbal Pad’s Owner’s Manual for instructions on attaching the cymbal pad to the cymbal holder.) B Step Left Side Assembly A Right Side Assembly C 4 Attach the Module Holder 4-1 Cymbal Pad Insert the Hex Rod Cylinder H into the Module Holder Clamp G , and tighten the fixing bolts. Step 4-2 4-3 4-4 6-2 Attach the Module Holder Clamp G to the Left Side Assembly A pipe. Attach the DTX to the Module Holder F . With a screwdriver, use the screws included with the Module Holder to attach the holder to the bottom of the DTX. Attach the Module Holder F (with the DTX attached) to the Module Holder Clamp G . Hex Rod Cylinder 5-1 Drum Pad Clamp (Long) J H Tighten Cymbal Holder K Cymbal Holder K Drum Pad Clamp (Long) J Step 6-1 DTX Drum Pad Clamp(short) Module Holder I F Step Step 4-3 Step 4-4 Step Hex Rod Cylinder 5-3 Drum Pad Clamp(short) H Step Tighten A I 4-1 Step Attach the Module Holder Left Side Assembly 5-2 4-2 G After the above assembly is complete, set the Kick Pad, Hi-Hat Control Pedal, etc. into position and connect the necessary cables. To keep cable out of the way while playing, use the supplied Cable Bands to hold the cables to the rack systems’s pipes.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res Create Date : 2004:12:07 13:39:04Z Modify Date : 2005:01:25 10:48:57+09:00 Page Count : 2 Creation Date : 2004:12:07 13:39:04Z Producer : Acrobat Distiller 4.05 for Macintosh Mod Date : 2005:01:25 10:48:57+09:00 Metadata Date : 2005:01:25 10:48:57+09:00EXIF Metadata provided by EXIF.tools