Yanfeng Visteon Automotive Electronics BTM01 2.4GHz Bluetooth Module User Manual BTM01
Yanfeng Visteon Automotive Electronics Co.,Ltd 2.4GHz Bluetooth Module BTM01
BTM01 User Manual
BTM01 User Manual
Features
Fully qualified Bluetooth® v2.1 + EDRspecification
Piconet and scatternet support
Minimum external components
UART to 4Mbaud
SDIO (Bluetooth Type A)/CSPI interface
Integrated CSR AuriStream® low-power codec for
wide-band voice quality
General Description
BTM01 is a single-chip radio and baseband Module for Bluetooth 2.4GHz systems
including EDR to 3Mbps.It is based on CSR BlueCore6-ROM QFN Automotive chip. It
provides a fully compliant Bluetooth v2.1 + EDR specification system for data and voice
communications.
BTM01includes AuriStream, which offers significant power reduction over the CVSD-
based system when used at both ends of the link.
Applications
Automotive
The device incorporates auto-calibration and BIST routines to simplify development, type
approval and production test. All hardware and device firmware is fully compliant with
the Bluetooth v2.1 + EDR specification.
Electrical parameters
VCC=3.3+/-0.3V
Operation temperature:-30 to 75 degree
Device Pinout
1BT_RST
2PCM_OUT
3 PCM_SYNC
4 BT_RX
5BT_TX
63.3V
7GND
8BT_RTS
9 BT_CTS
10 PCM_CLK
11 PCM_IN
12 GND
EC DECLARATION OF CONFORMITY
We Yanfeng Visteon Automotive Electronics Co.,Ltd. declared that following
designated product:
Product Name: Bluetooth Module of R0-13
Model No: BTM01
Complies with the essential protection requirements of the Radio and
Telecommunication Terminal Equipment Directive (EC Directive 1999/5/EC) and the
Electromagnetic Compatibility Directive(2004/108/EC).
This declaration applies to all specimens manufactured identical to the samples
submitted for testing/evaluation. Assessment of compliance of the product with the
requirements relating to the Radio and Telecommunication Terminal Equipment
Directive (EC Directive 1999/5/EC) and the Electromagnetic Compatibility
Directive(2004/108/EC) was performed by British Approvals Board for
Telecommunications (BABT) (Notified Body No.0168), based on the following standards:
Safety:
EN 60950-1:2006+ A1:2010+A11:2009+A12:2011
IEC 60950-1:2005+A1:2009
EN 62479:2010
Radio:
ETSI EN 300 328 v1.7.1
EMC:
ETSI EN 301 489-1 v1.9.2
ETSI EN 301 489-17 v2.2.1
NOTE: This equipment has been tested and found to comply with the limits for a
ClassB digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generate, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Caution: the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Caution: the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.