Yazoo Kees Sbsic050 Rhon050 Users Manual OM, Comber/Rake, 2002 02, RBSIC050, RBSIT550, RBSIT551, SBSIC050, (Turf Care)

RBSIC050, RBSIT550, RBSIT551, SBSIC050, RHON050 to the manual cb2945cc-6dce-45e1-8108-1eacc0abc934

: Yazoo-Kees Kees-Sbsic050-Rhon050-Users-Manual yazoo-kees-sbsic050-rhon050-users-manual-474408 yazoo-kees pdf

Open the PDF directly: View PDF .
Page Count: 11

MANUAL No. 100431 REV. 07 (02/19/02)

Professional Quality Lawn Care Equipment

since 1945

Thank you for buying a YAZOO/KEES! Before operating your new power rake, read,

understand and follow the important safety instructions and the other instructions con-

tained in this manual. Lawnmowers and all power equipment, can be potentially danger-

ous if used improperly. SAFETY REQUIRES GOOD JUDGEMENT, CAREFUL USE

IN ACCORDANCE WITH INSTRUCTIONS AND COMMON SENSE.

Safety and Operator's Manual for

Printed in U.S.A.

RBSIC050

RBSIT550

RBSIT551

SBSIC050

RHON050

MODELS:

2

IMPORTANT SAFETY INSTRUCTIONS

2. Do not put hands or feet near or under rotating parts. Keep

clear of discharge area while engine is running.

3. Stop engine when crossing gravel drives, walks, roads, or

under any condition where thrown objects might be a hazard.

4. After striking a foreign object or if machine vibrates

abnormally, stop the engine and disconnect the spark plug.

Inspect the machine for any damage and repair the damage.

5. Stop the engine whenever you leave the operating position

for any reason, including clearing debris, inspecting, or

making adjustments.

6. Rake across slopes, never up and down. Use caution

when changing direction on slopes. Do not rake very steep

slopes, or areas where stability or safety might be in doubt.

7. Do not rake water-soaked lawns. This will pull turf off the

surface. Cut tall grass before raking.

MAINTENANCE

1. Keep all nuts, bolts, and screws tight to keep mower in

safe operating condition.

2. Never store machine with gas in the tank inside a building

where fumes can reach an open flame or spark. Allow engine

to cool before storing in an enclosure.

3. To reduce fire hazard, keep machine free of grass, leaves,

or excessive grease.

4. Have your machine inspected and serviced each year by

an authorized Yazoo/ Kees dealer. Determine if any additional

devices are available which might upgrade the safety of your

machine.

5. Use only authentic Yazoo/Kees replacement parts to

insure the safety of your machine is maintained.

TRAINING

1. Read this manual carefully and question your dealer if

something is not clear.Should the dealer be unable or

unavailable to answer to your satisfaction, write or call our

factory. Be thoroughly familiar with the controls and proper

use of the equipment.

2. DO NOT allow children in yard or area when machine is

operated.

3. DO NOT allow pre-teenage children to operate unit.

4. Allow only responsible teenagers with mature judgment to

operate machine and only under close supervision.

5. Keep the area clear of all persons, particularly small

children and pets.

PREPARATION

1. Never operate machine without proper guards, covers,

safety switches and devices in place and properly functioning.

Inspect to determine that these safety devices are installed

properly, are in good repair, and operate properly. If the

condition of these devices are questionable, they must be

repaired or replaced before using the machine.

2. Thoroughly inspect the area where machine is to be used

and remove all stones, sticks, wire, and other debris. Also

note the location of holes, stumps, and other possible

hazards.

3. Do not operate the machine when barefoot or wearing open

shoes.Always wear substantial footwear and long pants.

4. Fill gasoline tank before starting the engine. Use only an

approved gasoline container. Do not smoke near open gasoline

container. Do not fill gasoline tank indoors or when engine is

running. Allow engine to cool off for at least 10 minutes before

refueling. Wipe off any spilled gasoline before starting engine.

Do not run engine indoors.

5. Never attempt to make a depth adjustment while engine

is running.

6. Operate only in daylight or in good artificial light.

7. Never operate machine in wet grass. Always be sure of

your footing; keep a firm hold on the handle and walk, never

run.

OPERATION

1. Do not change engine governor settings or overspeed the

engine.

WARNING: Failure to comply with the following instructions may result in serious injury to the operator or other persons. The

owner of the machine must understand these instructions, and must allow only persons who understand these instructions

to operate the machine. Each person operating the machine must be of sound mind and body and must not be under the

influence of any substance which might impair vision, dexterity or judgment. If you have any questions about your machine

which your dealer cannot answer to your satisfaction , call or write YAZOO / KEES POWER EQUIPMENT, Beatrice, NE

68310 ( Phone 402-223-2391)

THE ENGINE EXHAUST FROM

THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE

OF CALIFORNIA TO CAUSE

CANCER, BIRTH DEFECTS OR

OTHER REPRODUCTIVE HARM.

!

!WARNING

3

FAMILIARIZATION

NOMENCLATURE

The nomenclature drawing above (Figure 1) shows the

essential parts of the Yazoo/Kees Power Rake/Slicer. It is

recommended that all operators of this equipment become

thoroughly familiar with the controls, parts and operation of

this machine before operating. Specific details involving the

engine are found in the seperate engine owner’s manual.

Study these manuals before operating and keep both handy

for future reference.

Figure 1

This manual has been prepared for the operators of the

Yazoo/Kees Power Rake, Model RBSIC050 and Slicer,

Model SBSIC050. Its purpose, aside from recommending

operating instructions and routine service requirements, is to

promote safety through the use of accepted operating

practices. READ, UNDERSTAND AND FOLLOW the safety

and operating instructions herein before attempting any work

with the machine.

4

OPERATING INSTRUCTIONS

Figure 2 Figure 4

BEFORE OPERATING:

Be thoroughly familiar with all controls and how to use them

before operating the Dethatcher/Slicer. Make the following

checks and perform the service as required before each start

up.

PRE-START CHECK LIST

CHECK ENGINE OIL and bring level up to full. (Refer to

engine manual for oil specifications).

CHECK AIR CLEANER and service according to instructions

in Engine Manual.

FILL FUEL TANK where fumes will be safely dissipated.

Refer to Engine Manual for fuel specifications.

CHECK DETHATCHER OR SLICER SHAFT ASSEMBLY to

make sure it is free of dirt and other debris.

CHECK EXTERNAL SURFACES and remove any dirt and

dust accumulation.

CHECK GUARDS to make sure all are in proper position and

securely tightened.

STARTING-STOPPING

Know beforehand how to stop the engine and rotation

of the DETHATCHER or SLICER shaft in preparation for

possible emergencies.

The engine of the DETHATCHER/SLICER is stopped by

pulling the engine THROTTLE CONTROL to the rear to

“STOP”. See Figure 2

Figure 3

Shaft rotation is stopped by releasing the CLUTCH CONTROL

BAIL. See Figure 3.

OPERATE ENGINE AS FOLLOWS:

STEP 1:

Move HEIGHT ADJUSTMENT LEVER to “TRANSPORT”

position. (This insures that the Shaft Assembly is clear of the

ground/pavement should accidental engagement of CLUTCH

CONTROL BAIL occur.) See Figure 4.

5

STEP 2:

On cold starts, move the CHOKE CONTROL on the engine

forward into “CHOKE" position. See Figure 5.

STEP 3:

Move THROTTLE CONTROL to the “RUN” position.

STEP 4:

While remaining on right side of unit, place foot on top of right

wheel, hold handle bar and pull ROPE STARTER on engine

in smooth, steady motion until engine starts. To prolong the

life of the rope, guide the STARTER handle back to the engine

rather than allowing it to snap back .

STEP 5:

Allow brief engine warm-up period, move CHOKE LEVER

rearward and move the engine THROTTLE CONTROL to the

rear to the desired speed setting. Refer to DETHATCHING/

SLICING section.

STEP 6:

To stop the engine, pull the engine THROTTLE CONTROL to

the rear to “STOP”.

HANDLE BAR ADJUSTMENT

Loosen knobs on each side of HANDLE BAR. Adjust

HANDLE BAR “UP” or “DOWN” as desired. Retighten

Knobs. See Figure 6.

Figure 5

Figure 6

TRANSPORTING TO SITE

To avoid damage to the machine, lawn or pavement, always

move HEIGHT ADJUSTMENT LEVER to “TRANSPORT”

position when moving from one location to another. Refer to

Figure 4. Also, when transporting, the

machine is more easily steered when tilted backwards onto

its rear wheels.

DETHATCHING PROCEDURE

The DETHATCHER/SLICER SHOULD NOT BE PULLED

BACKWARDS! If an area must be gone over again, turn the

machine around.

NOTE

*Do not use this machine on wet or water soaked

lawns. This will pull turf off the surface of the lawn,

particularly in rough or bumpy areas.

*Before using your machine, inspect the lawn and

remove all sticks, stones, wire and any foreign objects

that are likely to damage the machine.

*Do not use machine in tall grass. You receive a

better job when raking after a recent mowing.

*Do not let the DETHATCHER set in one spot without

having the clutch disengaged. Failure to do this will

cause the unit to dig up turf.

OPERATING INSTRUCTIONS

6

Figure 7

Figure 8

1. SET HANDLE BAR in desired position before engaging

CLUTCH CONTROL.

2. SET HEIGHT ADJUSTMENT LEVER to desired raking

height.

3. SET SPEED by moving THROTTLE CONTROL to desired

speed setting.

4. BEGIN dethatching by stepping behind DETHATCHER,

lifting “UP” on CLUTCH CONTROL BAIL and pushing machine

forward.

5. TO MAKE SHARP TURNS, release CLUTCH CONTROL

BAIL and tilt machine back on its rear wheels.

DETHATCHER DEPTH ADJUSTMENT

Normal Depth Adjustment on the DETHATCHER is

accomplished by placing the machine on a hard surface,

making sure one of the satellite shafts is at dead bottom, and

adjusting the wheels so that the fingers are just touching the

ground. (IMPORTANT: DO NOT set the fingers so that they

will penetrate the ground. This will counteract the centrifugal

force of the fingers and prevent them from doing a proper de-

thatching job).

Through constant use, the raking edges of the fingers will

begin to wear. When this occurs, remove the end plates and

turn the entire Shaft Assembly, end-for-end and replace it in

the machine. This will give the fingers a new square raking

edge. See Figure 7.

SLICING PROCEDURE

The following text gives instructions for making depth

adjustments on the SLICER. For machine operation, see

“DETHATCHING PROCEDURE” in preceding column.

SLICER DEPTH ADJUSTMENT

Normal depth setting for proper blade penetration for slicing

and aerating is approximately 1/2" to 3/4" into the ground. To

obtain the proper setting, place the machine on the lawn

surface and adjust the wheel height one to two notches.

For the crawling type grasses such as Bermuda, Zoysia,

Bahia, St. Augustine, etc., the setting is obtained in the

same manner, except the wheels are raised only one notch.

For single strand grasses such as Bluegrass and Rye grass,

it is best to slice in two separate directions, perpendicular to

each other. For example, when slicing the first time,

direction of travel is north and south. Then it is best to slice

again in a east-west direction. (IMPORTANT: It is necessary

to water thoroughly after the aerating process is complete.

Fertilizer and seed, if desired, can be applied after slicing).

As the blades wear, they may be rotated four times to give

new cutting edges each time. See Figure 9.

Extra holes in the Main Shaft are provided for longer life of the

Main Shaft. If the hole holding the satellite shaft becomes

distorted, rotate all four (4) satellite shafts to the next

adjacent hole. See Figure 8.

OPERATING INSTRUCTIONS

7

Figure 10Figure 9

Figure 11

MOVING PARTS: (ALL MACHINES)

1. Lubricate HEIGHT ADJUSTMENT LEVER and related

parts monthly (or more often if required) with oil.

2. SATELLITE oil to assure free movement of FINGERS.

SERVICE PARTS & ASSISTANCE

To retain the original quality of your DETHATCHER/SLICER,

use only genuine Yazoo/Kees replacement parts. Specify

the model and serial number as found on the nameplate of

your machine when contacting your Yazoo/Kees Dealer for

parts or service assistance.

Your Yazoo/Kees Dealer has a complete listing of all

components. For engine parts, look for the engine

manufacturer’s dealers under the heading ENGINES - gasoline

in the yellow pages of your telephone directory.

DETHATCHER/SLICER LUBRICATION

CRANKSHAFT ASSEMBLY: Lubricate each ENDCAP

BEARING with 2 shots of grease every 8 operating hours and

before running if unit has been unused for a long period of

time. See Figure 10.

WHEELS: DETHATCHER/SLICER

Lubricate each wheel with 1 shot of grease every 8 operating

hours. See Figure 11

OPERATING INSTRUCTIONS

8

SERVICE

Figure 13

Figure 12

2. Lubricate SATELLITE SHAFTS on DETHATCHER with

CLUTCH CONTROL CABLE

Lubricate CABLE with oil, graphite or a penetrating-

type spray lubricant as required.

BELT/CLUTCH ADJUSTMENT

Position of Bail when CLUTCH engages, is adjusted by

loosening jam nuts on threaded barrel end of CLUTCH

CONTROL CABLE, turning jam nuts to desired position, then

tightening in new position. See Figure 13.

CAUTION:

NEVER ADJUST MACHINE WITH

ENGINE RUNNING

OFF SEASON STORAGE

Thoroughly clean all external surfaces,

Shaft Assembly (including Fingers or Slicers) and underside

of unit before storing the unit. Grease all fittings and lubricate

all wear surfaces with oil.

1. Drain gasoline from fuel system and drain the crankcase

oil (Refer to Engine Manual for details).

2. At the start of the new season, replenish engine crankcase

oil and add gasoline to the fuel tank.

3. Before starting, move the ENGINE CONTROL to “STOP”

and pull Rope Starter slowly several times. If excessive

resistance is felt, remove the spark plug and pull Rope Starter

rapidly to spin the engine and clear oil from the cylinder.

Clean and reinstall the spark plug before attempting to start

the engine.

9

Yazoo/Kees Limited Two Year Warranty

1. This Limited two-year Warranty is issued by Yazoo/Kees Power Equipment, only to the original

purchaser. The warranty period is limited to ninety (90) days when product is or has been used

for rental purposes.

2. Yazoo/Kees warrants that all new equipment manufactured by Yazoo/Kees (Yazoo/Kees Prod-

ucts), listed in paragraph 9 hereof, shall be free of defects in material and workmanship for the

term described in paragraph 4 below. Component parts, equipment, and accessories not manu-

factured by Yazoo/Kees are not warranted hereunder, but are warranted by the original manu-

facturer only to the extent of any original manufacturer’s warranty, with the exception of the

following; five years on wheel motors, ninety days on belts, hoses, tires, and battery, one year

on electrical components, and one year on Peerless model 700 transmissions (first ninety days

warranted by Peerless, remainder by Yazoo/Kees).

3. In the event that any Yazoo/Kees Product warranted hereunder shall be defective or fail to

conform with this limited warranty, Yazoo/Kees shall, subject to the provisions hereof, pay for,

or provide labor and materials for, the repair or replacement of such defective Yazoo/Kees

Product.

4. This limited warranty is for two years (24 months) from purchase date for Yazoo/Kees Products.

5. To obtain limited warranty service on a Yazoo/Kees Product use this procedure:

a. Locate the nearest Yazoo/Kees dealer or distributor.

b. If you have moved, notify any Yazoo/Kees dealer or distributor in your area. You must

be able to confirm purchase date to validate your warranty.

c. Make arrangements to have the equipment delivered to the dealer or distributor (refer

to paragraph 6a).

d. If you have questions concerning the Yazoo/Kees Limited Warranty, they should be

referred to :

Yazoo/Kees Power Equipment

P.O. Box 8

700 Park Street

Beatrice, NE 68310

Attention: Customer Service Department

(402) 223-2391

e. Warranty service on Yazoo/Kees Products must be performed by an authorized Yazoo/

Kees dealer.

6. This limited warranty does not cover the following:

a. Transportation to and from the Yazoo/Kees dealer or distributor.

10

b. Normal maintenance services and normal maintenance items such as brakes, brake

shoes, spark plugs, oil, air filters, mower blades, gauge wheels, skids and other wear

items.

c. Any Yazoo/Kees Product which had been altered or modified in any way.

d. Any repair or replacement caused by customer neglect or lack of maintenance. (The

purchaser is responsible for making sure that Yazoo/Kees Products are operated and

serviced as directed in the applicable manual or service instruction. Incorrect use or

maintenance will void this Limited Warranty.

7. YAZOO/KEES MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, OR WARRAN-

TIES AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

ALL WARRANTIES ARE LIMITED IN DURATION TO THE TERMS SET OUT IN PARA-

GRAPH 4, ABOVE. YAZOO/KEES SHALL HAVE NO LIABILITY FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING FROM THE BREACH OF ANY WAR-

RANTY, INCLUDING, BUT NOT LIMITED TO, LIABILITY FOR INCONVENIENCE,

RENTAL OR PURCHASES OF REPLACEMENT EQUIPMENT, OR FOR LOSS OF PROF-

ITS OR OTHER COMMERCIAL LOSS. SOME STATES DO NOT ALLOW A LIMITA-

TION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE STATEMENT

MAY NOT APPLY TO YOU. SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

8. This warranty is not subject to change or modification by anyone, including Yazoo/Kees dealers

or distributors, and no Yazoo/Kees dealer or distributor is authorized to make any representa-

tions on behalf of Yazoo/Kees Power Equipment.

Note: This Warranty is for the following machines or products:

•ZTMax Midmount Riding Mowers

•Kutter Midsize Walk-behind Rotary Mowers

•Power Rake Dethatchers

•Power Slicer Aerators

•Core Plugger Aerators

•Classic High-wheel Walk-behind Rotary Mowers

11