York Lx Mini Split Air Conditioners Owner S 898147 UUM B 0713 User Manual
Lx-Mini-Split-Heat-Pumps-Owner-S york-lx-mini-split-heat-pumps-owner-s-manual
Lx-Multi-Zone-Multi-Split-Heat-Pumps-Owner-S york-lx-multi-zone-multi-split-heat-pumps-owner-s-manual
Mini-Split-Air-Conditioner-Users-Manual york-mini-split-air-conditioner-users-manual-812479
Johnson-Controls-Johnson-Controls-Inc-Air-Conditioner-16-Users-Manual-566924 johnson-controls-johnson-controls-inc-air-conditioner-16-users-manual-566924
16 to the manual 2867acee-fa53-42a8-a593-2e155962c6ca
2014-07-06
User Manual: York Lx-Mini-Split-Air-Conditioners-Owner-S
Open the PDF directly: View PDF 
.
Page Count: 10
| Download | |
| Open PDF In Browser | View PDF |
USER’S INFORMATION MANUAL SINGLE AND MULTI-ZONE DUCTLESS SYSTEM AIR CONDITIONER OR HEAT PUMP MODELS: 16 & 22 SEER TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DUCTLESS SYSTEM DEFFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . 2 EQUIPMENT MODEL NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DUCTLESS SYSTEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TYPICAL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 GENERAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 REMOTE CONTROL BATTERIES REPLACEMENT . . . . . . . . . . . . .6 EMERGENCY OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 INSTALLATION AND MAINTENANCE OF HEALTHY FILTER . . . . .7 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 CONTACT INFORMATION • • Johnson Controls Unitary Products Consumer Relations 5005 York Drive Norman, OK 73069 Go to website at www.york.com, then click on “Contact Us” and follow the instructions. Contact us by mail: Read this manual and keep for future reference. GENERAL LX SERIES PREMIUM SERIES This Manual is a guide to help assist with the operation of this ductless system. It does not contain the service procedures that have to be performed by a qualified HVAC service technician. • Make sure you read this manual before you start operating your new ductless system. • After reading this manual, if you still need more information that may not have been covered in this manual, please contact your HVAC contractor. • To ensure comfort, make sure that temperature selection has been properly set at the remote control. To ensure efficient operation, do not block air intake or outlet at either the indoor or outdoor unit. Also, do not stand nor put items on top of outdoor and indoor units. • If any issues with your system were to arise, please contact your HVAC contractor. • Make sure your windows and doors are shut when operating your ductless system. NOTICE The refrigerant inside your ductless product uses PVE oil (Polyvinyl Ether Oil) that readily absorbs moisture from the atmosphere. To limit this “hygroscopic” action, the system should remain sealed whenever possible. If a system has been open to the atmosphere for more than 4 hours, the compressor oil must be replaced. Do not break a vacuum with air and always change the driers when opening the system for component replacement. For specific handling concerns with PVE oil, contact your HVAC contractor. Failure to follow these recommendations could result in equipment damage. Johnson Controls Unitary Products 898147-UUM-B-0713 898147-UUM-B-0713 SAFETY MULTI-SPLIT SYSTEM A multi-zone system consists of a single outdoor unit and two to five indoor units. Each zone is controlled separately by a remote control (included with the indoor unit). ELECTRICAL SHOCK, FIRE, OR EXPLOSION HAZARD. • This product must be installed and serviced by a qualified installer or service agency. Improper or incomplete installation, adjustment, alteration, service or maintenance could cause personal injury, loss of life, or damage to property. Installation and service must be performed by a licensed professional dealer or contractor. • Failure to follow safety warnings exactly could result in dangerous operation, serious injury, death or property damage. • When servicing your ductless system, your HVAC contractor must use factory supplied service and replacement parts. Failure to follow these instructions may result in property damages such as fire, personal injury or death. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. • The power supply must be of proper amperage and conform with local codes. • Don't cut or damage the power cords and control cords. Electric shock or fire could result. If they are damaged, immediately call your HVAC contractor to have your ductless system serviced. • Do not operate your ductless system without the air filter installed. The air filter should be removed and cleaned periodically to assure maximum efficiency. • If a burning smell or smoke occurs, please turn off the power supply immediately and contact your HVAC contractor. Not doing so may cause electric shock or fire. • Do not use flammable sprays near your ductless system. They can cause a fire or explosion. • R410A Refrigerant High Pressure Warning! The units described in this manual use R410A refrigerant which operates at 50 to 70% higher pressures than R-22. Failure to use R-410A approved service equipment could result in equipment explosion which could result in death or serious injury. • The refrigerant provided by the manufacturer complies with all the requirements of this system. When using recycled or reprocessed refrigerant, its quality has to be as good as that of a new refrigerant. It is necessary to have the recycled or reprocessed refrigerant tested by a qualified laboratory. Failure to do so could void the warranty. • Grounding your ductless system is required! Follow proper local electrical code on requirements for grounding. Failure to follow code could result in death or serious injury. • Do not use this system if it has been in a flooded area and underwater. Call a licensed HVAC professional to inspect the system and replace controls and electrical components that have been damaged or replace the system, if determined necessary. • Keep combustible materials at least 3 feet away from either the indoor or outdoor unit. • Do not insert your hands, tools or any other item into the air intake or air outlet at either the indoor or outdoor unit. • If outdoor unit is installed on a raised stand, check condition of stand occasionally to ensure its stability. EQUIPMENT MODEL NUMBERS TABLE 1: OUTDOOR MODEL NUMBER INDOOR MODEL NUMBER LX 16 SEER Single Split Cooling Only Model Numbers DCMF09CSM42Q1 DCMF09NWM42Q1 DCMF12CSM42Q1 DCMF12NWM42Q1 DCMF18CSM42Q1 DCMF18NWM42Q1 DCMF24CSM42Q1 DCMF24NWM42Q1 LX 16 SEER Single Split Heat Pump Model Numbers DHMF09CSM42Q1 DHMF09NWM42Q1 DHMF12CSM42Q1 DHMF12NWM42Q1 DHMF18CSM42Q1 DHMF18NWM42Q1 DHMF24CSM42Q1 DHMF24NWM42Q1 Premium 22 SEER Single Split Cooling Only Model Numbers DCPM09CSM41Q1 DCPM09NWM41Q1 DCPM09CSM42Q1 DCPM12CSM41Q1 DCPM12CSM42Q1 DCPM18CSM42Q1 DCPM24CSM42Q1 DCPM09NWM42Q1 DCPM12NWM41Q1 DCPM12NWM42Q1 DCPM18NWM42Q1 DCPM24NWM42Q1 DCPM36CSM42Q1 DCPM36NWM42Q1 Premium 22 SEER Single Split Heat Pump Model Numbers DHPM09CSM41Q1 DHPM09NWM41Q1 DHPM09CSM42Q1 DHPM09NWM42Q1 DHPM12CSM41Q1 DHPM12NWM41Q1 DHPM12CSM42Q1 DHPM12NWM42Q1 DHPM18CSM42Q1 DHPM18NWM42Q1 DHPM24CSM42Q1 DHPM24NWM42Q1 DHPM30CSM42Q1 DHPM30NWM42Q1 DHPM36CSM42Q1 DHPM36NWM42Q1 LX 16 SEER Multi-Splits Heat Pump Outdoor Unit Model Numbers DHMF18CMM42Q1 \ DHMF24CMM42Q1 \ DHMF30CMM42Q1 \ DHMF36CMM42Q1 \ DHMF42CMM42Q1 \ LX 16 SEER Multi-Splits Heat Pump Indoor Unit Model Numbers \ DHPM09NWM42Q1 \ \ DHPM12NWM42Q1 DHPM18NWM42Q1 DUCTLESS SYSTEM DEFFINITIONS SINGLE SPLIT SYSTEM A single split system consists of a single outdoor unit and a single indoor unit. The single split system is controlled using a remote control (included with indoor unit). 2 Johnson Controls Unitary Products 898147-UUM-B-0713 DUCTLESS SYSTEM OPERATION MUTI-SPLITS APPLICATION ONLY In a multi-split application, the operating mode is determined by the zone that initiates the first demand for heating or cooling. If the system is energized and a heating demand has been initiated by zone 1, an error code (E7) will be displayed of the front panel of the indoor unit of any zone trying to initiate a cooling demand. The zone 1 remote (and remotes for other zones calling for heating) must be powered off in order to allow the system operating mode to switch to the cooling mode. Once the zone initiates the cooling demand, the mode will have to be reset in the same way to allow a heating demand in another zone. This situation occurs only when there are very different requirements in two or more zones in the system. SINGLE SPLIT AND MULTI-SPLITS APPLICATIONS COOLING MODE OPERATION 1. Cooling Mode Operation Principles - In the cooling mode, the indoor coil absorbs the heat from the room and transfers it to the outdoor coil where it is discharged. The system cooling capacity is affected by the outdoor ambient temperature. The indoor fan operates continuously in cooling mode even when the cooling setpoint temperature is reached. The indoor unit swing louver is fixed in an upward position. The cooling operating range of the outdoor unit is typically from 5°F (-15°C) to 115°F (46°C) for small capacity systems (9K & 12K) and 14°F (-10°C) to 115°F (46°C) for large capacity systems (18+K). 2. Anti-Freezing Protection in Cooling Mode - If the unit is running in cooling mode and frost starts forming on the indoor coil, the outdoor unit compressor will stop to protect your ductless system. 1. AUTO Mode - Cooling Operation - If the indoor ambient temperature is greater than 77°F (25°C), the ductless system will operate in cooling mode and will continue to run until the indoor ambient temperature reaches 75°F (24°C). At this point, the outdoor unit's compressor and outdoor fan will operate for another 60 seconds, then they will both turn off. The indoor fan will run continuously at a speed determined by the indoor ambient temperature. When the system is in AUTO mode and in cooling operation, the indoor unit swinging louver is fixed in an upward position. 2. Auto Mode - Heating Operation (heat pump only) - If the indoor ambient temperature is less than 68°F (20°C), the system will operate in heating mode and will continue to run until the indoor ambient temperature reaches 69°F (21°C). At this point, the outdoor unit's compressor and outdoor fan will operate for another 60 seconds, then they will both turn off. The indoor fan will run continuously at a speed determined by the indoor ambient temperature. When the system is in AUTO mode and in heating operation, the indoor unit swing louver is fixed in a downward position. FAN MODE OPERATION When the system is set to operate in FAN mode, the indoor fan runs continuously in AUTO, low, medium or high speed. The outdoor unit is off. In AUTO fan mode, the fan speed is determined by the indoor ambient air temperature. DRY MODE OPERATION When the system is set to operate in DRY mode, the indoor fan runs continuously at low speed to maximize indoor air moisture removal. TYPICAL INSTALLATION SINGLE SPLIT HEATING OPERATION 1. Heating Operation Principles - The refrigerant flow is reversed during the heating cycle. The outdoor coil absorbs the heat from outside and transfers it to the indoor coil where it is discharged into the living space. The system heating capacity is also affected by the outdoor ambient temperature. In heating mode, the indoor blower will continue to operate for 60 seconds after the outdoor unit shuts off. The indoor unit swing louver is fixed in a downward position. The heating operating range of the outdoor unit is from 19 °F (7°C) to 75°F (24°C). In extreme low temperature conditions, it may be necessary to supplement heating using other means such as space heater, fireplace, etc. 2. Auto Defrost - When the outdoor temperature is low and/or with high humidity, frost may form on the outdoor coil, reducing the ability of the unit to transfer energy. The unit will go into Auto Defrost mode and the heating will be discontinued for 8 to 10 minutes. When the defrost cycle is complete, the system will start running in heating mode. While the outdoor unit is in defrost mode, the following occur: • The fan motors of the indoor and outdoor units will stop running. • The indoor unit indicator flashes, and moisture may flow from the outdoor unit and steam may be observed. 3. Cold Air Prevention - Hot Heat Pump - In heating mode, if the indoor coil has not achieved a certain temperature, the indoor fan will not operate for up to 3 minutes. This may occur during: • Initial start-up of a heating cycle • Immediately after completion of an Auto mode operation • Heating under extremely low indoor temperatures INDOOR UNIT AIR IN 3 2 ON/OFF 7 4 5 6 AIR OUT 1. Power Cable* 2. Remote Control 3. Front Panel 2 4. Filter 5. Guide Louver 6. Wall Pipe 7 Bind Tape OUTDOOR UNIT 8. Drainage Pipe * To be provided at field AIR IN 1 AUTO MODE OPERATION 8 When AUTO mode is selected, the setpoint temperatures in heating and cooling modes are predetermined. When AUTO mode is activated, the remote control temperature setpoint and fan operation cannot be adjusted. AIR OUT FIGURE 1: Single-Split Indoor Johnson Controls Unitary Products 3 898147-UUM-B-0713 MULTI-SPLITS AIR IN 1 INDOOR UNIT 2 5 AIR OUT 4 3 8 1. Front Panel 2. Filter 3. Guide Louver 4. Wall Pipe 6 5. Bind Tape 6. Connection Wire 7 7 Drainage Pipe 8. Remote Control OUTDOOR UNIT 18 KBTU OUTDOOR UNIT (ONE TO TWO ZONES) 24 KBTU OUTDOOR UNIT (TWO TO THREE ZONES) 42 KBTU OUTDOOR UNIT (TWO TO FIVE ZONES) 30 KBTU OUTDOOR UNIT (TWO TO FOUR ZONES) FIGURE 2: Multi-Split Units 4 Johnson Controls Unitary Products 898147-UUM-B-0713 REMOTE CONTROL OPERATION The wireless remote control gives the homeowner the ability to operate their ductless system at the touch of a button. The indoor unit and remote control send information back and forth continuously. The remote control must be placed on a table or other surface in direct line of sight with the indoor unit infrared receiver. The remote control should not be placed in a drawer. Make sure that there are no obstructions between the indoor unit receiver and the remote control. Make sure you do not throw nor drop the remote control. The remote should never come in contact with liquids and should not be left in direct contact with the sun or any place that's very hot. POWER BUTTON When this button is pressed, the system will turn on. When pressed the second time, the system will turn off. When turning the system on or off, the Timer and Sleep functions (if activated) will be canceled; however the clock time will be continue to operate even when the system is off. MODE BUTTON Press this button to select system operating modes. AUTO mode is the default setting when the system is AUTO turn on. As MODE button is pressed, COOL COOL, DRY, FAN and HEAT (for heat pump only) modes can be DRY selected in this order. The selected FAN mode is displayed on both the HEAT remote control and the indoor unit's (Only for cooling and heating units) cover panel displays. When AUTO mode is selected, the temperature will not be displayed. When in COOL mode, the default setpoint temperature is 77°F (25°C). When in HEAT mode, the default setpoint temperature is 69°F (21°C). +/- BUTTONS Use plus (+) and minus (-) buttons to adjust the temperature setting up or down. NOTICE The temperature cannot be adjusted when the system is in AUTO mode. FAN BUTTON Press FAN button to select fan speed. AUTO AUTO fan is the default setting. In MIDDLE FAN LOW FAN AUTO fan mode, the indoor fan speed HIGH FAN is determined by the indoor ambient temperature. Press FAN button to select the desired fan setting in the following order AUTO, Low Speed, Medium Speed and High Speed. The fan speed selection is displayed at the top of the remote control display by one of these symbols. NOTICE I FEEL BUTTON Press the I FEEL button to activate the I FEEL feature. When the I FEEL icon appears, the system will satisfy your cooling or heating (heat pump only) setpoint temperatures where the remote control is located. Press the I FEEL button again to deactivate. When I FEEL function is deactivated, the system will satisfy the cooling and heating (heat pump only) setpoint temperatures where the indoor unit is located. To use the I FEEL mode, the remote control must be placed in direct line of sight with the indoor unit infrared receiver. Make sure that there are no obstructions between the indoor unit receiver and the remote control when I FEEL feature is activated. SWITCH FROM °C TO °F With system OFF, press MODE and (-) buttons simultaneously to switch from Centigrade to Fahrenheit. The current selection is displayed to the right of the temperature display on the remote control. CLOCK BUTTON Press the CLOCK button to adjust the time displayed on the remote control. The clock icon will flash. Press the (-) and + buttons to adjust the time up or down in one minute increments. Press and hold the button to adjust the time in 10 minute increments. Press the CLOCK button again when correct time is displayed. If no button is pushed for 5 seconds while the display is still flashing, the timer setting will not be saved. X-FAN BUTTON Press the X-FAN button once to initiate extended blower operation. This function allows removal of excess moisture from the indoor unit coil after in order to prevent possible mold or bacterial growth. When the X-FAN function is activated, the indoor fan will continue to run at low speed for 10 minutes after the unit is turned off using the POWER button. The extended fan operation icon is displayed when this feature is turned on. To deactivate, press X-FAN button again and the indoor unit fan will stop running. LOUVER SETTING BUTTON Press this button to set the position of the indoor unit swing louver. When this feature is turned on, icon appears on the remote OFF control display. Continue to press the LOUVER icon to select the desired swing angle as shown in the following sequence. When activated, the louver will start swinging right to left. SLEEP BUTTON Use the SLEEP button to activate or cancel the sleep function. To activate sleep function, press SLEEP button and the sleep icon should appear on the remote control display. Press SLEEP button to cancel sleep function and the sleep icon on the remote control should disappear. In cooling mode, SLEEP function increases temperature by 2°F per hour over a two hour period from the time sleep function is activated. In heating mode, SLEEP function decreases temperature (-2°F per hour) over a two hour period from the time sleep function is activated. Sleep function is defaulted to off when the system is turned on. If the system is turned off the Sleep function is automatically disabled. NOTICE The sleep function is not available in AUTO or FAN modes. The fan speed is not adjustable in DRY mode operation. The low fan speed is necessary to ensure optimal humidity control. Johnson Controls Unitary Products 5 898147-UUM-B-0713 TIMER ON BUTTON Use the TIMER ON button to initiate or cancel a single timed ON event. Use this feature to bring the system on when you return home or when you wake up in the morning. Press the TIMER ON button once. The clock icon disappears and a time setting appears with the word ON flashing at the right. Use the (-) and + keys to adjust the time setting to the desired time for the system to begin operation. Press the TIMER ON button again to accept the setting. To make sure the function is turned on successfully, the word ON will appear to the right of the current time display. Press the TIMER ON button again if you want to cancel the timed ON event. TIMER OFF BUTTON Use the TIMER OFF button to initiate or cancel a single timed OFF event. Use this feature to turn the system off when you leave the house or when you go to sleep. Use the same method described above to set the desired time for the system to stop operation. To make sure the function is turned off successfully, the word OFF will appear to the right of the current time display. Press the TIMER OFF button again if you want to cancel the timed OFF event. REMOTE LOCK Press (-) and + buttons simultaneously to either lock or unlock the remote control buttons. When locked, the icon is displayed. TEMP BUTTON Use the TEMP button to change the temperature display shown on the remote control. When the system is powered on, the current temperature setting is displayed along with this icon . Press the TEMP button one more time to display the current indoor ambient temperature, along with this icon . Press the TEMP button again to display the outdoor ambient temperature with this icon . The selected temperature will return to the display screen after 5 seconds. The TEMP button can also be used to temporarily display the indoor ambient temperature on the indoor unit display panel. 9. Use X-FAN button to turn on and off extended fan operation feature in cooling and DRY modes. 10. Use TURBO button to speed up cooling or heating. 11. Use I FEEL button to control your setpoint temperature from the remote control in cooling and heating modes. REMOTE CONTROL BATTERIES REPLACEMENT If the remote control operation becomes erratic, remove batteries. Wait 30 seconds and reinsert batteries. If proper remote control operation is not restored, replace batteries. The wireless remote control requires two AAA, 1.5V batteries. Follow the steps below and the illustrated graphics to replace the batteries when necessary. Use the LIGHT button to turn the indoor unit display light on and off. When the light is on, the icon appears on the remote control. If the wireless remote is lost or damaged, the system can be operated using the manual switch or code switch. The system will run in AUTO mode, and will not change the temperature setting or the fan speed. 5. Press button, to activate the swinging louver. Press again to select a desired louver angle. 6. Press SLEEP button to initiate sleep function. Press again to deactivate. 7. Use TIMER ON and TIMER OFF buttons to schedule desired timed on and off settings 8. Use LIGHT button to set display light on or off. 6 3 If the remote control is not going to be used for a long period of time, make sure to remove batteries to avoid damage to the control. EMERGENCY OPERATION 1. To turn the system ON, press ON/OFF button, the system should start to run. (Note: when the system is powered off, the swing louver of indoor unit will close automatically). 2. Press MODE button to select the desired mode. Keep pressing until the desired mode is displayed on the remote control. 3. Pressing +or - button to set the desired temperature (temperature cannot be adjusted in AUTO mode). 4. Keep pressing FAN button to select desired fan speed. Fan speed selection is as follow: AUTO FAN, LOW, MID and HIGH. 1 1. Remove screw that secures the battery access panel to the remote control. Slide the panel in the direction of the arrow. 4 2. Remove the existing AAA, 1.5V batteries. 3. Replace batteries with fully charged AAA, 1.5V batteries. Make sure to pay attention to proper polarity of batteries. Remote control will not operate if batteries are improperly installed. 4. Reposition battery access panel and slide forward until panel snaps into locked position. 5. Reinsert screw. LIGHT BUTTON GENERAL OPERATION 2 The manual switch can be operated as follows: • To operate the unit, press the AUTO/STOP button once and the unit will enter into AUTO RUN mode. The microcomputer will select the (COOL, HEAT, FAN) mode automatically to maintain optimum room comfort. • To stop the unit from operating, press the AUTO/STOP button once and the unit will shut down. AUTO/STOP MANUAL SWITCH AUTO TEST RUN STOP CODE SWITCH The code switch can be operated as follows: • To operate the unit, adjust the code switch to the AUTO position and the unit will enter into AUTO RUN mode. The microcomputer will select the (COOL, HEAT, FAN) mode automatically to maintain optimum room comfort. • To stop the unit from operating, adjust the code switch to the STOP position and the unit will shut down. Johnson Controls Unitary Products 898147-UUM-B-0713 NOTICE The TEST button is for the technicians' testing, which should not be used by our user. MAINTENANCE OUTDOOR UNIT 1. Ensure power is off before cleaning. 2. It may be necessary to wash the outdoor coil more frequently if it is exposed to substances which are corrosive or which block airflow across the coil (e.g., pet urine, cottonwood seeds, fertilizers, fluids that may contain high levels of corrosive chemicals such as salts). 3. Outdoor Coil (Sea Coast) - Moist air in ocean locations can carry salt, which is corrosive to most metal. Units that are located near the ocean require frequent inspections and maintenance. These inspections will determine the need to wash the unit including the outdoor coil. Consult your installing contractor for proper intervals/ procedures for your geographic area or service contract. 4. Outdoor unit fan motor is pre-lubricated and sealed. No further lubrication is needed. 5. Visually inspect all connecting lines, joints and coils for evidence of oil leaks. 6. Check all wiring for loose connections. 7. Check for correct voltage at unit (unit operating) Fig. B AIR FILTER HEALTHY FILTER Fig. C FIGURE 3: Filter Replacement CLEANING AND MAINTENANCE INDOOR UNIT 1. 2. 3. 4. 5. 6. Fig. A Clean or change filters. Check all wiring for loose connections Check for correct voltage at unit (blower operating). Clean coil, if necessary. Check connecting lines and coils for signs of oil leaks. Check condensate line and clean, if necessary. NOTICE The filter must be in place and the front panel must be closed any time the unit is in operation. INSTALLATION AND MAINTENANCE OF HEALTHY FILTER (ACCESSORY) INSTALLATION OF HEALTHY FILTER (REFER TO FIGURE 3) • Lift up the front panel from its two ends and remove the factory supplied air filter as shown in Fig.A. • Attach the healthy filter to the air filter as shown in Fig. B. • Install the air filter properly as shown in Fig. C and then close the panel. • Remove the healthy filter and clean thoroughly. Do not use a brush or any hard objects to clean the filter. • Dry the air filter before reinstalling it. TROUBLESHOOTING Whenever there is a problem with the system, an error code will be displayed on the front cover of the indoor unit. If more than one error has occurred, the codes will alternate so that all codes are shown. Make note of the code (E4, F6, H4, etc.), then reset the display by pressing the ON/OFF button on the wireless remote. Press the ON/OFF button a second time to reapply power to system. If code is still displayed, disconnect and restore power at the unit disconnect switch or circuit breaker. If the problem was temporary, the code will not reappear. If the error code reappears after power has been restored, contact your HVAC contractor. If one of the following situations occur, please unplug the unit and contact your HVAC contractor immediately: • • • • • • There is very loud sound during operation The strong odor coming from the indoor unit during operation Water is leaking into the room Circuit breaker trips frequently Water or other liquid has been splashed into the indoor unit There is an abnormal heat in power supply cord and power plug If none of the above conditions exist, check the following items before calling your HVAC contractor. Johnson Controls Unitary Products 7 898147-UUM-B-0713 * The temperature readout (either temperature setpoint or indoor ambient) will be replaced by an error code if there is a malfunction. If multiple errors are detected, the display will alternate between each error code. INFRARED SIGNAL RECEIVER DEHUMIDIFY MODE RUN TEMPERATURE* NOTE: No history is kept on past error codes. COOL INDICATOR HEAT INDICATOR 72 FIGURE 4: Indoor Unit Front Panel Indicators TABLE 2: Problem Possible Cause Unit does not operate immediately after being restarted. Unit control initiates a 3 minute delay at the end of each cycle to protect the compressor from damage. A whoosh or gurgling noise can be heard at Sometimes, the refrigerant can be heard in the indoor coil when the outdoor unit starts or stops the indoor unit. operation. This is not a malfunction. Mist is coming out of the indoor unit during cooling operation. This sometimes happens when the indoor temperature and humidity are very high and the air is being cooled quickly. The mist will disappear as the indoor temperature and humidity are lowered. A creaking or popping noise can be heard when the unit starts or stops. The plastic components of the indoor units sometimes expand and contract when they are heated and cooled. Are the TIMER ON and TIMER OFF features being used incorrectly? Unit is not operating. Is power disconnected or has circuit breaker tripped. Is power shut down? Is temperature setting correct? Are either the air inlet or air outlet blocked on the outdoor or indoor unit? System is not cooling (or heating) efficiently. Is filter dirty? Is fan at low speed? Are windows and doors properly shut? Wireless remote is not working. Water is leaking from indoor unit. Water is leaking from condensate line at indoor unit. Is remote in direct line of sight with indoor unit infrared receiver? Has the remote been damaged? Remove remote control batteries for 30 seconds, then reinsert them. Replace batteries, if necessary. Indoor humidity level is very high and water is being blown from indoor coil. This will stop as humidity level is reduced. Check condensate line outside to make sure it is not obstructed. Check condensate line to make sure it has not been disconnected from indoor unit. During operation in high humidity areas, condensate will form on cold outdoor refrigerant pipes. Water is leaking from the outdoor unit. Clicking noise heard inside. When heat pump is operating in defrost mode, ice will thaw from around outdoor coil and water will flow from the unit. Sometimes, the sound of the outdoor unit fan or compressor relay can be transmitted in a way that makes it seem to be coming from the indoor unit. Heat pump units − In HEAT mode, a timed delay keeps indoor fan off for two minutes to prevent unheated air from being circulated by the indoor fan. Indoor fan is not working. Heat pump units − In HEAT mode, cold outdoor temperatures and high humidity cause frost to accumulate on the outdoor unit. When this happens, the unit will enter a defrost cycle. The indoor fan is off during the 3 − 12 minute cycle. In DRY mode, indoor fan operation may be stopped to avoid delivery of moist air to the room. Do not adjust temperature setting. 8 Johnson Controls Unitary Products 898147-UUM-B-0713 Limited Warranty WARRANTY TERMS: Johnson Controls Unitary Products (hereinafter “Company”) warrants this product to be free from defects in factory workmanship and material under normal use and service and will, at its option, repair or replace any parts, without charge, subject to the exclusions below, that prove to have such defects according to the terms outlined in this warranty. Company reserves the right, at its sole discretion, to provide a replacement unit in the place of repair parts, in which case the warranty period for the replacement unit is limited to the remainder of the original warranty period. Alternatively, Company may, at its option, extend a replacement allowance to be applied toward the purchase of a new unit marketed by Company. The exact amount of the allowance will be determined at the discretion of Company, based upon current market conditions, but in no case shall this allowance exceed thirty (30) percent of the original consumer purchase price of the unit excluding such items as ductwork, wiring, piping, and installation costs. The warranty period for repair or replacement parts or unit provided hereunder shall not extend beyond the warranty period stated below. Company shall have no responsibility hereunder for installation, shipping, handling, or other charges except as specifically provided herein. This warranty covers only the equipment described by the Product Model Number and Unit Serial Number on the equipment or listed on the Warranty Registration Card, and applies only to products installed in the United States, Canada, or Puerto Rico. Tampering, altering, defacing, or removing the product serial number will serve to void this warranty. This warranty extends only to the original consumer purchaser and is nontransferable. For this warranty to apply, the product must be installed according to Company recommendations and specifications, and in accordance with all local, state, and national codes; and the product or residence must not be removed from its place of original installation. This warranty does not apply to any unit sold over the Internet, by telephone or other electronic means unless the dealer that buys or sells a unit over the Internet, by telephone or other electronic means also installs the unit. In the absence of a recorded Warranty Registration Card, the warranty period will begin upon product shipment from Company. If you are unaware of the date the warranty became effective, contact Company at (877) 874-7378 or visit www.upgproductregistration.com. ADDITIONAL CONDITIONS FOR HEAT EXCHANGER WARRANTY: This warranty shall cover the heat exchanger (primary and/or secondary, if applicable) only if: 1. The product has not been operated with an input rate in excess of the rating plate attached to the product. 2. The product has not been allowed to operate without the use of the proper automatic limit control on the maximum warm air temperature and/or without adequate circulation. 3. The product is installed so that the combustion air is not contaminated by compounds of chlorine, fluorine, or other damaging chemicals (or vapors). 4. The product is installed such that the heat exchangers are not exposed to return air temperatures below stated ratings. FOR PRODUCT REGISTRATION: For your benefit and protection, register your product with Company promptly after installation. This will initiate the warranty period and allow us to contact you, should it become necessary. You can register your product online at www.upgproductregistration.com or by returning the Warranty Registration Card on the back page of this packet. Product Model Number: _________________________________ Installation Date: _________________________________ Unit Serial Number: ____________________________________ Installing Dealer: _________________________________ FOR WARRANTY SERVICE OR REPAIR: Notify your Installing Dealer or a Participating Dealer, preferably in writing, as soon as possible after discovery of the problem. Be sure to include the Product Model Number, Unit Serial Number, Installation Date, and a description of the problem. You may find the Installing Dealer's name on this page or on the equipment, and you can locate Participating Dealers online at www.yorkupg.com. If a Dealer response is not received within a reasonable amount of time, notify Company at: Johnson Controls Unitary Products, Consumer Relations, 5005 York Drive, Norman, OK 73069 or by telephone at (877) 874-7378. All warranty service or repair will be performed during regular business hours, Monday through Friday 9:00 AM - 5:00 PM. Service requests sent to Company without prior Dealer contact will be referred back to a Participating Dealer. Because this process takes time, it is in the best interest of the Consumer to contact a Participating Dealer directly. WARRANTY PERIOD: The warranty period in years, depending on the part, is as shown in the chart below. CONDENSING UNITS CONDENSING UNITS ALL MODELS COMPRESSOR PARTS 6 years 2 years MAINTENANCE: Company strongly recommends regular periodic preventive maintenance on this equipment. The person most familiar with the equipment in your HVAC system is a Participating Dealer. The Participating Dealer can ensure that your maintenance program meets the “Company Warranty” conditions, maximize the equipment efficiency, and service your unit within the mandated guidelines with regard to unlawful discharge of refrigerants into the atmosphere. Johnson Controls Unitary Products 9 EXCLUSIONS: This warranty does not cover any: 1. Shipping, labor, or material charges or damages resulting from transportation, installation, or servicing. 2. Damage or repairs required as a consequence of mishandling, faulty installation, misapplication, abuse, improper servicing, unauthorized alteration, or improper operation. 3. Damages or failure to start resulting from improper voltage conditions, blown fuses, open circuit breakers, or other inadequacy or interruption of electrical service or fuel supply. 4. Fuses, either internal or external to the product. 5. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing, or handling of either defective parts or replacement parts. 6. Products removed from their original location for reinstallation purposes. 7. Damages resulting from accident, abuse, fire, flood, alteration, or acts of God. 8. Damages resulting from use of the product in a corrosive atmosphere. 9. Normal maintenance, or damages resulting from failure to perform normal maintenance, as outlined in the installation and servicing instructions or owner's manual. 10. Cleaning or replacement of filters, nozzles, or orifices. 11. 11. Damages resulting from operation with inadequate supply of air or water; Damages resulting from failure to properly and regularly clean air and/or water side of condenser and evaporator. 12. Damages resulting from: (I) freezing of condenser water or condensate; (II) inadequate or interrupted water supply; (III) use of corrosive water; (IV) fouling or restriction of the water circuit by foreign material or like causes. 13. Damages caused by improper parts, components or accessories not suitable for use in or with the unit. For a list of parts that are known to be compatible please reference the equipment renewal parts list, contact a Participating Dealer for assistance, or call 1-877-874-7378. 14. Electricity or fuel costs, or increases in fuel or electric costs, for any reason including additional or unusual use of supplemental electric heat. This warranty is in lieu of all other express warranties. All implied warranties, including the implied warranty of merchantability and fitness for a particular purpose are limited in duration to the actual warranty period applicable to the part. Some states do not allow the disclaimer of implied warranties, so the above disclaimer may not apply to you. In addition, some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event, whether as a result of breach of warranty or contract, tort (including negligence), strict liability, or otherwise, shall Company be liable for special, incidental, or consequential damages or expenses, including but not limited to loss of use of the equipment or associated equipment, lost revenues or profits, cost of substitute equipment, or cost of fuel or electricity. The above limitations shall inure to the benefit of Company's suppliers and subcontractors. The above limitation on consequential damages shall not apply to injuries to persons in the case of consumer goods. Company does not assume, or authorize any other person to assume for Company, any other liability for the sale of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Subject to change without notice. Published in U.S.A. Copyright © 2013 by Johnson Controls, Inc. All rights reserved. 898147-UUM-B-0713 Supersedes: 898147-UUM-A-0112 York International Corp. 5005 York Drive Norman, OK 73069
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : csardom Create Date : 2013:08:05 08:30:43-05:00 Modify Date : 2013:08:05 08:32:41-05:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2013:08:05 08:32:41-05:00 Producer : Acrobat Distiller 10.0.0 (Windows) Format : application/pdf Title : 898147-UUM-B-0713.fm Creator : csardom Document ID : uuid:2e397b17-37f1-4d35-9dfb-abcd8d0eb2b3 Instance ID : uuid:7bd1329a-44c5-4406-8e8d-989d84af3b71 Page Layout : OneColumn Page Mode : UseThumbs Page Count : 10EXIF Metadata provided by EXIF.tools