Youngs Watch MD15366 Bluetooth Smart Watch User Manual 16690 YPM MD15366 101x75P46 Youngs E

Youngs Watch Co., Ltd. Bluetooth Smart Watch 16690 YPM MD15366 101x75P46 Youngs E

User Manual

Select(1) This device may not cause harmful interference, and FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsi-ble for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (2) this device must accept any interference received, including interference that may cause undesired operation.Sports type: walking and runningSOS For SOS number setting see Page17.StepDistanceSpeedSelect the type of pedometerIn the pedometer on state,press and hold "B" switch to the type of pedometer.WalkingRunningSports type: walking and running.The goal of step range: 1000~100000.Distance of walk&run: 30~180cm, 4~118inch.Weight range: 20~200kg, 44~440lbs.Height range: 90~221cm, 35~87inch.Age range: 07~99.CaloriesTime of walking/runningClear data2sWhen a user continuous walking/running movement after 10 steps, the watch will record cumulative step. RecallTotal recordTotal step Record1Step Clear data2sPress and hold key "C" After 2sRecord mode"C""D""B""A"After 3~5sUser opens the APP, and click the icons below, it will open the APP interface.Chart A --- Interface for time setting, controlling camera thru BT, watch locator & other functions.Chart AThe directions of APP home and icons are shown below.Chart B --- For browsing sports data.Chart C --- For browsing sleeping data.Chart D --- For changing sports parameters & setting the sleep monitoring & sedentary reminderWhen mobile phone and watch are in normal connection state, clicking "synchronization" button, the APP data will synchronize with the watch (sync the latest 7 days sports data with the watch); click "Share" button, user can share the sports data to QQ, WeChat, Facebook......Click hereToday sports data Yesterday sports data This month sports data The sports data from last monthClick here, the APP data will synchronize with the watch dataIn the APP sports interface, the user can browse the intraday steps, distance, calories consumption and time.In the APP sports interface, the user can browse historical data (including the daily and monthly sports data).In the APP sleeping interface, the user can browse intraday deep sleep time, shallow sleep time, sleep quality and other data(for a single sleep time less than 2 hours, no sleep statistical data will be recorded).In the APP sleeping interface, user can browse the historical data (including the daily and monthly sleeping data).In this function we can set the age, weight, target steps, tracks the distance, the same method used in the height function.The sport parameter setting Adjusting numeric valueSelect numeric valueClick confirm(Taking height setting as an example)Click "confirm" button, the parameter setting of thewatch user will coincide with the APPSetting sex When the watch bluetooth function is off, it cannot set the step parameter by APP, the user can enter pedometer mode to set the sports parameter (see Page30).The operation to set the height is the same as setting the sleeping time on and off (see Page11).When the watch bluetooth function is off, it can not set the sleeping time ,on and off for the watch.Timekeeping mode The setup is successfulAfter 2sClick the APP of "confirm" buttonWhen the watch display "Done", it means the sports parameter setting is finishedSlide up the phone'sscreenSetting up sleep monitorSleeping switch"Confirm" buttonSetting the sleeping time (on and off)When the watch display "Done", it means the sleeping monitor setting is finishedFor watch sleeping monitor parameter setting, see Page12.For more details of watch sports parameter setting, see Pages11or 30.Sports interface When the sleeping monitor setting is "on", & the current time within sleeping monitor time, the watch will display " " icon, it will monitor the user sleeping quality;Can browse the sleeping time and quality by APP (see Page10).Setting up sedentary reminderSedentary switchSetting the sedentary on and off timeWhen the watch display "Done", it means the sedentary reminder setting is finishedSetting the sedentary on and off as well as time is the same method used in the height function (see Page11).When the watch bluetooth function is off, it cannot set the sedentary on and off as well as time for the watch.When the watch sedentary reminder setting is "ON", the watch will display" " icon.No caller ID in contacts With caller ID in contactsFor callers not in contacts, the watch will display the telephone numberwhile for those from contacts, the watch will display phone's address book name(only english name).USER'S MANUAL( Bluetooth Smart Watch )Made in ChinaNon-professionals, do not disassemble.16690-YPM(MD15366)-EThe operation of buttons are indicated by using the letters shown in the illustration. BUTTONSA -- S et / ResetB -- ModeC -- EL backlight / -D -- Start / Stop / +EL (electro-luminescent) is used as backlight to glow for easy reading in the dark.Use EL Backlight In the timekeeping mode, press "C" to illuminate the display about 3 seconds.BACKLIGHTDAC Dhaka +06BKK Bangkok +07HKG Hong Kong +08Tokyo +09TYOSydney +10SYDNoumea +11NOUWellington +12WLGGuam, VladivostokSeoul, PyongyangSingapore, Kuala Lumpur, Beijing, Taipei, ManilaJakarta, Phnom Penh, Hanoi, VientianeNovosibirsk, ColomboSuva, Christchurch, Nauru Island, NadiPort vilaKarachi +05KHI MaleDXB Dubai +04 Abu Dhabi, MuscatJeddah +03JEDCAI Cairo Cape Town , Sofia, Athens, Helsinki, IstanbulParis +01PAR Milan, Rome, Amsterdam, AlgiersMadrid, London +00LON (UTC), Lisbon, Casablanca, ReykjavikRIO Rio de Janeiro -03-04Buenos Aires, MontevideoLa Paz, Port Of SpainNew York -05NYC Montreal, Detroit, Miami, Boston, Panama CityCHI Chicago -06 Houston, Dallas/Fort Worth, New OrleansDEN Denver -07 Phoenix, Edmonton, Chihuahua-08LAX Los Angeles San Francisco, Las Vegas, Vancouver, SeattleANC Anchorage -09 NomeHNL Honolulu -10 PapeetePago Pago -11PPG Pago Pago City code City Other major cities in same time zone Differential GMT +02SCL Santiago-02-01FENRAI PraiaFernando de NoronhaMoscow, Addis Ababa, AdenFernando deNoronhaPraiaWorld Time Form3. In the timekeeping mode BLE off state, press and hold "D" to turn on the watch bluetooth function( "Link" will be displayed); BLE off state "Hold" flashingAfter 2sNext page5. When the watch is connected with the phone, all icons are displayed in color in the APP main menu.Click YoungsWatch or 2U WatchClickhereAfter 2sDoneContinued from previous pageBLE on stateSetting menuMain menuPress and hold key "D"Link Continued from previous page4. When mobile phone locates the watch, click YoungsWatch or 2U Watch, a few seconds later, the watch will be connected to the phone automatically;Before using APP, please ensure the mobile phone and watch are already connected normally.Click settingClick okBack tothe main menu Scanning... Click connect watchNext pageContinued from previous pageNotification accessClick here1. Never try to open the case or remove its back cover.2. Do not operate buttons underwater.3. Should moisture appear inside the watch, have it checked immediately by your dealer. Otherwise it can cause corrosion of the metal parts of the watch.4. Though the watch is designed to withstand normal use, you should avoid rough use or dropping the watch. 5. Avoid exposing the watch to extreme temperatures.6. Wipe the watch with dry, soft cloth only. Avoid allowing it to come into direct contact with chemical materials, which can cause deterioration of the plastic parts of the watch. 7. Avoid to wear the watch in electromagnetic, static conditions.A T T E N T I O NThe screen shown in below:DISPLAYDateDay of weekSecondsAlarmChimeLow power indicatorDaylight saving timeMinutesHourBuletoothBuzzerVibrationCall NoticeMessage Notice E-Mail NoticeEvent NoticeSleep SedentaryWalk RunIf the battery voltage level is insufficient, the icon " " will appear to remind to replace a new battery.Change BatteryCoin can be used to open the battery hatch and change with the same battery specification.Caseback of the watch sketch CoinLOW POWERTROUBLE SHOOTING3. Click Youngs Watch APP, in the APP main menu state, click "setting\ disconnection" to clear current connection;2. At mobile phone bluetooth menu state , un-pair "ALL" paired device;When user is unable to connect bluetooth function, please follow the steps below to re-pair the watch and mobile phone."Hold+Clear" flashing Clear connectionUser modeAfter 2s1. To enter mobile phone setting menu, check the bluetooth function is on or not;Click setting Click disconnect Click ok5. Please re-pair APP(See Page 5~7).Press and hold key "D"4. In the user mode USER state (when the watch bluetooth function is off), press and hold "D" to clear historical connection(clear the display " " ); Pacer Setting1. In the pacer mode, press and hold "A" until the tempo number will flash (flashing is indicated in the setting mode); 1. Press "D" to start; 2. To stop, press "D" again.Use The Pacer3. Press "A" to exit the set state after setting.iPACER2. Press "C" or "D" to select the tempo in the following sequence: 10 20 30 40 50 60 70 80 90 100 120 140 160 180 200 240 280 320; 2. In the world time mode, press and hold "A" to turn ON/OFF the Daylight Saving Time.1. In the world time mode, press "D" to forward select the time zone, press "C" to backward select the time zone, press and hold to adjust at high speed; hWORLD TIME Countdown Timer Setting1. In the countdown mode, press and hold "A" until the hour will flash (flashing is indicated in the setting mode); 3. Press "B" to select the next selection;2. Press "D" to increase the hour, press "C" to decrease the hour, press and hold to adjust at high speed; 1. Press "D" to start the countdown timer; 2.To pause, press "D" again.Use Countdown Timer6. Press "A" to exit the set state after setting.4. Press "D" to increase the number, press "C" to decrease the number, press and hold to adjust at high speed;gCOUNTDOWN When the countdown timer reacheszero, the alarm beeps for about 10 seconds, press any button to stop it. 5. Repeat steps 3 and 4, the selection in the following sequence: Hour Minutes Seconds;3. Press "A" to reset the stopwatch.A Lap Time1. In the stopwatch mode, press "D" to start the stopwatch;3. Press "A" to reset the stopwatch.2. To stop the stopwatch, press "D" again;5. Press "D" to stop the stopwatch;Split Time2. Press "A" to display the split time, stopwatch timing continues internally; 4. Repeat steps 2 and 3, you can measure the multi split time;3. Press "A" to clear the split time and to continue time measurement;1. In the stopwatch mode, press "D" to start the stopwatch;f STOPWATCH Alarm And ChimeThe alarm beeps about 10 seconds at the preset time each day, press any button to stop it.Alarm Time Setting1. In the alarm state, press and hold "A" until the hour will flash, the indicator " " appears (flashing is indicated in the setting mode);eALARM5. Press "A" to exit the set state after setting. 3. Press "B" to select the minutes;4. Press "D" to increase the minutes, Press "C" to decrease the minutes, press and hold to adjust at high speed;2. Press "D" to increase the hour, press "C" to decrease the hour, press and hold to adjust at high speed; In the alarm mode, press "D" to turn on/off the alarm and chime in the following sequences: Alarm & Chime off Alarm on Chime on Alarm & Chime on.aTIMEKEEPING Time Setting2. Press "C" or "D" to select the city code, press and hold to adjust at high speed; 1. In the timekeeping mode, press and hold "A" until the city code will flash(flashing is indicated in the setting mode);3. Press "B" to select the Daylight Saving Time;4. Press "C" or "D" to turn ON/OFF the Daylight Saving Time.6. Press "A" to exit the set state after setting (The day of week is automatically displayed in accordance with year, month and date setting).5. Repeat steps 3 and 4, the selection in the following sequence: City code Daylight Saving Time Seconds Hour Minutes 12/24H Format Year Month Date Key Tone(ON/OFF);BLE off state"Hold" flashingLink cartoonTurn ON The BluetoothIn the BLE off state, press and hold "D" to turn on bluetooth function.Press and hold key "D"After 2sBLE on stateBLE offPress and hold key "D"After 2s"Hold" flashingIn the BLE on state, press and hold "D" to turn off bluetooth function.Turn OFF The BluetoothWhen the watch bluetooth is on, please refer to page5~7 for the pairing method.The icon " " is displayed after the watch pairing is successful.(Timekeeping mode)SleepCountdown TimerBattery(CR2032)ChimeAlarmEL BacklightStopwatchWorld Time11 100 Years Calendar50 50M Water Resistant PacerMessage NoticeE-Mail Notice Event NoticeCall NoticeSOSSOSVibrationFind CameraSync TimeSafety Range NoticePedometerLow power indicatorSedentary Notice(Timekeeping mode)eALARMChime;18 tempo(10 ~ 320).iPACERhWORLD TIMEThe time for other time zones. The alarm sounds at the preset time each day.FIND, Camera.bUSERMODE SELECTIONaTIMEKEEPINGHour, Minutes, Seconds, Year,Month, Date, Day of week;12/24H Format;100 years Calendar(2000 ~ 2099).cPEDOMETERfSTOPWATCH1/100 second unit;Measuring range:0'00"00 ~ 99:59'59".gCOUNTDOWNCountdown timer range:99:59'59" ~ 0'00"00.Step range: 0~999999;Press "B" to change the mode in the following sequence:Timekeeping Mode User Mode Pedometer Mode Record Mode Alarm Mode Stopwatch Mode Countdown Timer Mode World Time Mode Pacer Mode.7 Records (Record1~Record7);Auto storage record.dRECORDSOS FINDCAMERAIn the BLE on state, press and hold "B" to perform SOS function.In the FIND state, press and hold "D" to perform watch find mobile phone function (See page18).In the camera state, press "D" toperform remote photo shooting function(See page19).When the watch bluetooth is off, the SOS and camera aredisabled.BLE on state(Timekeeping mode)Press and hold key "B"After 2s"Hold" flashingWhen the watch bluetooth is off, the SOS is disabled.Setting USERFINDbUSERSelectIn the user mode, press "A" to select USER, FIND, CAMERA function.Press key "A" 6. Press "A" to exit the set state after setting.1. In the user state, press and hold "A" until the icon " " flash (flashing is indicated in the setting mode); 2. Press "D" to select the remind methods in the following sequence:buzzing vibration buzzing+vibration silent;3. Press "C" to select the remind methods in the following sequence:buzzing vibration buzzing+vibration silent;Press key "A" CAMERARE-CONNECTThe watch will automatically re-connect with mobile phone after PS wake up (See page21).The watch after safe range remind state & back to safe range within 1 minute, it will automatically re-connect with mobile phone (See page20).The watch and mobile phone are in normal connection state, if short time disconnections will be encountered (maybe caused by environmental interference or other causes), this does not mean that there is something wrong with the watch, after a few seconds the watch will automatically re-connect with mobile phone.In the re-connecting state, the watch will automatically connect with the mobile phone several times, it will automatically close bluetooth function after 1 minute if still unable to connect with the watch.At the watch bluetooth function off state, phone, message, e-mail, event reminder and other functions are disabled, user need to turn on the watch bluetooth function manually to connect with mobile phone again(See page6~7).Enter PSPOWER SAVINGPower saving setting(See page28).The watch bluetooth function will automatically turn off after entering power save mode, the mobile phone and watch will automatically disconnect to save battery power.Wake up PSPS mode Moving the watchMoving the watch after1 minute Timekeeping " " flashingAfter 2sAfter a few secondsTimekeeping Connect succeed At the watch bluetooth function off state, phone, message, e-mail, event reminder and other functions are disabled.For receiving reminder of phone call, message, e-mail, event and others on time, user can turn off the PS function (See page28), please be reminded it will consume more battery power (shorten battery life).When PS setting is on, the mobile phone and watch are in normal connection state, if no watch activity happens within 10 minutes, it will automatically enter to power saving mode ( "PS" displayed).When watch is in PS mode , it will automatically go back to timekeeping mode, the watch will automatically wake up if an activity happens within 1 minute (the watch will automatically re-connect with mobile phone).When the distance between watch and mobile phone is beyond the safe range(around 6 meters), the watch will alarm and/or vibrate to remind user( " " flashing).After the beyond safe range reminder, if user is back to safe range within 1~2 minutes, the watch will automatically re-connect with mobile phone.SAFE RANGE REMINDAfter 2sTimekeeping mode Back tosafe rangeConnect succeed Safe range remind When the watch icon " " is flashing, press any button to stop it (the watch bluetooth function will automatically turn off ). The watch will alarm and/or vibrate to remind user( " " flashing) when the mobile phone bluetooth function is turned off .1. In the App main menu state, click icon to enter picture taking screen; Camera3. In the user mode camera state, press "D" to perform remote photo shooting function.Click camera2. Aim the camera through the phone screen to take photo; After 2sPress key "D"Remote photo shootingCAMERA4. Press "B" to select the PS;5. Press "C" or "D" to turn ON/OFF the PS function (PS ON/OFF).Four methods of reminder setting:buzzing, vibration, buzzing+vibration, silent.Click "Find Youngs Watch"F I N DThe Mobile Phone Find Watch The Watch Find Mobile Phone In the user mode FIND state, press and hold "D" to perform the watch find mobile phone function, the mobile phone will alarm and/or vibrate to remind user.FIND state "Hold" flashingAfter 10sAfter 2sPress and hold key "D"The watch find mobile phone After 10sThe mobile phone find watchTimekeeping modeIn the APP main menu state, click icon to perform the mobile phone find watch function, the watch will alarm and/or vibrate to remind user.Click SOS Input SOS phone number2. In the setting menu state, click SOS to set the phone number.SOS SettingS O SClick settings1. In the APP main menu state, click the icon to enter setting menu.Activate the SOS function"Hold" flashingTimekeeping modeAfter 10sPress and hold key "B" After 2sSOS UseIn the timekeeping mode, press and hold "B" to activate the SOS function, the mobile phone will automatically call SOS number.SOS only available for android system, iOS system do not support thisfeature.SYNC TIME"AT" flashing DoneAfter 2sThe watch time will synchronize with mobile phone time after completing bluetooth time calibration.Click set clockTimezone setting3. The watch will automatically go back to timekeeping mode after bluetooth time calibration is finished.1. In the APP main menu state, click the icon to enter bluetooth time calibration menu;Sync timeClick sync timeTimekeeping mode2. In the bluetooth time calibration menu state, click sync time, the watch time will synchronize with mobile phone; After a few secondsIn the APP main menu state, click the icon to turn on/off the message notice( ).In gray means the function is offE-mail NoticeIn the APP main menu state, click the icon to turn on/off the E-mail notice ( ).In gray means the function is offEvent NoticeIn the APP main menu state, click the icon to turn on/off the event notice ( ).In gray means the function is offWhen having new E-mail on phone, the watch will alarm and/or vibrate to remind user, at the same time the watch icon " " will be flashing, press any button to stop it.After Youngs Watch APP event setup, when the event time is up, the watch will alarm and/or vibrate to remind user, at the same time the watch icon" " will be flashing, press any button to stop it.The requirement of E-mail address: Gmail, yahoo e-mail for android system, iCloud e-mail for iOS system.Calling DeclinePress any buttonNOTICECall rejection only available for android system, iOS do not support this feature.When there is an incoming call, the watch will alarm and/or vibrate to remind user, at the same time the watch icon " + CALL" will be flashing ("Rolling displayCaller ID and phone's address book") pressing any button will reject the call.Call NoticeMessage NoticeIn the APP main menu state, click the icon to turn on/off the call notice (In gray means the function is off).When there is missed call, the watch icon " " will be flashing, press any button to stop it.When having new message on phone, the watch will alarm and/or vibrate to remind user, at the same time the watch icon " " will be flashing, press any button to stop it.Press key "D" cPEDOMETERTurn ON/OFF The PedometerIn the pedometer mode, press "A" to turn on/off the pedometer.2. Press "C" or "D" to set the goal of step;1. In the pedometer mode, press and hold "A" until the goal of step to flash (flashing indicated in setting mode);Setting3. Press "B" to select the sex;4. Press "C" or "D" to switch the sex between male and female;5. Repeat steps 3 and 4, the selection in the following sequence: The goal of step Sex Age Metric/Imperial Height Weight Distance of Walk Distance of Run;6. Press "A" to exit the set state after setting.The Parameter Setting RangeAfter 3sPress and hold key "B" Recall In the pedometer mode, press "D" to browse the information in the following sequence: Step distance speed calories time of walking/running.Press key "D" Press key "D" Press key "D" Clear DataIn the pedometer mode, press and hold "C" 2s ("Hold+Clear" flashing), reset the data (thetotal data no change). Please turn off the pedometer to save power if you do not use the pedometer.When the mobile phone and watch are in normal connection state, click APP "sync" button to browse the updated data(see Page9).dRECORD In the record mode, press"A" to browse the selection in the following sequence: total record record1~record7. In the total record state, press "D" to browse the information in the following sequence: Total step total distance totalcalories total time of walking&running.Press key "D" Press key "D" Total distanceTotal caloriesTotal time of walking & runningPress key "D" Press key "D" In the record1 state, press "D" to browse the information in the following sequence: Step distance calories time of walking/running.Press key "D" Continued from previous pageNext pageDistancePress key "D" Press key "D" Press key "D" CaloriesTime of walking/running The way to recall record1~record7 is the same.Clear In the record1~record7 state, press and hold "C" for 2s ( "Hold+ Clear" flashing), clear the current record and return to total record (the total record no change).In the total record state, press and hold "C" 2s ("Hold+Clear" flashing), will reset all the data.The pedometer automatically store a record for more thanone minute walking when thedate is updated.The latest day exercise record isrecord1 (R01). NAVIGATION KEY MAUNAL SPORTChart BChart C Chart DClick hereClick hereSLEEPToday sleeping data Yesterday sleeping data This month sleeping dataClick here, the APP data will synchronize with the watch dataSleeping interfaceClick hereClick hereClick hereWhen mobile phone and watch are in normal connection state, clicking "synchronization" button, the APP data will synchronize with thewatch(sync the latest 7 days sleep data with the watch); click "Share" button, user can share the sleep data to QQ, WeChat, Facebook......The sport parameter settingClick hereClick confirmSetting unitsSetting up sleep monitorThe sports parameter settingClick the APP of "confirm" buttonAfter 2sThe setup is successfulTimekeeping modeTimekeeping modeTimekeeping mode The setup is successfulThe setup is successfulAfter 2sAfter 2sClick the APP of "confirm" buttonClick the APP of "confirm" buttonSetting up sedentary reminderSlide up the phone'sscreenSetting up sleep monitorClick confirm Otherwise during the exercise, note walking slowly, going along thebrae up and down, walking in the crowded place, standing and sitting again and again, playing ball, up and down sporting without normal walking will affect normal step counting, it is not a sign of watch malfunction . Exercise may include some risk, especially for those who have been sedentary. Before starting a regular exercise program you are recommended to answer to the following questions for health status checking. If the answer is YES to any of the questions, we recommend to consult a doctor before starting an exercise.Minimising Possible Risks In ExercisingHave you not exercised for the past 5 years?Do you have high blood pressure?Do you have high blood cholesterol?Do you have symptoms of any disease?Are you recovering from a serious illness or medical treatment? It is important to be sensitive to your body's reactions during exercise.If you feel unexpected pain or excessive fatigue when exercising, it is recommended to stop the exercise or continue at a lighter intensity.WARNING19103456782911 141312 15 16 17 18120 21 22 2336 37 38 4224 25 26 27 28 29 30 31 32 33 34 35 39 40 41 43 44 This watch belongs to the general sports and sleeping measure level meter & does not necessarily replace precision measurement equipment.PS---Power Saving. The watch is already an electronic precise one for monitoring sports and sleeping, but due to possible user operation errors, external interference or failure factors, etc., the results may become inaccurate which is only for users' reference and we also advise the watch to be used in conjunction with medical equipment.W-Time --- Walking Time; R-Time --- Running Time. When the user reach the set targetsteps, the watch will beep for about 10 seconds ("GOAL" flashing), press any button to stop it. Share ShareSleep Level: very good, good, general, poor, very poor.The sleeping data from last monthif the current time is out of sleeping monitor time or the sleeping monitor setting is "off", the watch icon " " will not be displayed.When the sleeping monitor setting is "on", the watch will monitor user's sleeping quality every day.The pedometer function will be automatically off when the sleeping monitor setting is "on"(the icon" " is displayed).For watch sleeping monitor default is off.APP INSTALLClick Youngs watch.apk Click nextInstalling...Click installClick confirmClick doneAPP Install For Android System1. Use mobile phone log in (searching on google play, find "Youngswatch" APP then follow the instructions to install on you mobile phone), if you mobile phone already installed "360 assistant" you can directly search "Youngswatch", then you can install the APP prompt.https://play.google.com/store2. To install the "Youngswatch" APP in the following steps:After a few secondsBluetooth version: BLE4.0 or above.Turn on APP Store Search "Youngswatch" then install Click install3. Click finish back to phone desktop, after finished the APP installation.APP Install For iOS SystemSearching on APP store and find "Youngswatch" APP then follow instructions to install to you phone.System Requirement For Mobile PhoneAndroid system: Samsung mobile phone android version 4.3 above (such as : Note4,Note5,Galaxy S5, Galaxy S6 and others), other brand mobile phone reference to use.iPhone system: iOS7.0 or above of iPhone 5/5s/6/6s...After 1sAPP PAIRINGLogo Guide page1Click startNotification accessClick here Next page1. Firstly turn on the phone's bluetooth function;2. Enter into APP search screen follow the steps as below: Click the icon Youngs watch on phone desktopGuide page2Guide page3Sliding phone screen to left Sliding phone screento left Please conduct pairing when the watch connect with mobile phone first time.

Navigation menu