Youngshin Electronics JR1800A433 Car Alram System User Manual R1800 AM FCC ID

Youngshin Electronics Co., LTD. Car Alram System R1800 AM FCC ID

Users Manual

USER’S GUIDER1800-AMFCC ID : 044JR1800A433Young Shin Electronics, Inc.www.magicar.comUSER’S GUIDEOne-Way AM RemoteFCC ID : O44JR1800A433This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device. R1800-AM
Page 2 Page 3TABLE OF CONTENTSSafety InformationRemote : R1800AMRemote Button FunctionsRemote Learn RoutineKeyless EntryAlarm ModeAuto-Start FunctionReservation ModeTrunk ReleasePanic ModeValet ModeTimer Start ModeSafety Shut Down FeaturesOptional Programmable FeaturesIgnition LockPassive LockingTurbo ModeOptional Installation FeaturesCold Start ModeOptional Auxiliary 1& Auxiliary 2Page 4Page 4Page 5Page 5Page 6Page 6Page 7Page 8Page 9Page 9Page 10Page 10Page 11Page 11Page 11Page 11Page 11Page 12Page 12Page 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...... . . . . . . . . . . ............. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The model name,R1800AM, is a Safety Information Please take these safety precautions into consideration under the following conditions : Under normal circumstances, Reservation Mode is cancelled when a door or hatchback opens. Please verify that the openingof any door or hatchback cancels Reservation Mode. If any of the doors or hatchbackare not monitored by Scosche because of improper installation or a faulty dome lightswitch, do not use the Scosche and take your vehicle immediately to the dealer forrepair. Do not set Reservation Mode if the window(s) are open or if there is anyone inside the vehicle, this includes animals. Remote start installation in a manualtransmission vehicle with a convertible top is not recommended.Page 4Important!When servicing your automobile (i.e. changing the oil, washing your car), the Young Shin Electronics, Inc system should be in Valet Mode. There is a safety shutdownswitch under the hood that deactivates the remote starter function if the hood is open. However, if the switch has been damaged or the switch has been installed improperly,the vehicle may start when the button is pressed for 2 seconds, even if the hood is open. Whenever you loan your vehicle to an individual who is not familiar with Young ShinElectronics, Inc, you may want to put the vehicle in Valet mode. This will prevent the borrower from accidentally activating the Scosche auto-security system. If the Young Shin Electronics, Inc. R1800 is installed in a manual transmission vehicle,extra precautions are required because the Scosche does not monitor the gear shifter : Remote : R1800AMPage 5Remote Button Functions123567891011121314Button Press Function0.5 sec Horn - on/off0.5 sec Valet Mode - on/off0.5 sec Passive Locking - on/off0.5 sec0.5 secTimer Start Mode - on/offTurbo Mode - on/off2 sec Programming Menu 1- Installer Only2 sec Programming Menu 2- Installer OnlyNote : ""Represents pressing the button for 2 seconds." "Represents simultaneously pressing the buttons." "Represents simultaneously pressing the buttons for 2 seconds.4Lock. If held for 3.5 seconds, it will panic the system.0.5 sec0.5 sec0.5 sec0.5 secUnlock2 sec Auto -start Function - on/offAuxiliary Option 2Auxiliary Option 1 2 sec Trunk Release3.5 sec Panic, Press to shut off the siren.Remote Learn RoutineThe Young Shin Electronics, Inc system will allow up to three remotes to be programmed to one vehicle. Please perform the following procedure to add orreprogram additional remotes.
Page 6Step2 :Within a 7 second period after cycling the ignition for the 5th time,Press the button for a 1/2 sec. The parking lights will flash once to confirm that the transmitter has been programmed. You can continue programming additional remotes. The parking lights will flash two times when the programming mode has expired. Keyless EntryTo lock the vehicle, press the button for 0.5 seconds.To unlock the vehicle, press the button for 0.5 seconds. If the pressing of thelock/unlock buttons does not lock/unlock the doors, you will need to release the button and try again, as the remote stops transmitting as soon as the LED stopsflashing. If the button is pressed for 3.5 seconds, it will panic the system.Alarm ModeTo arm the vehicle, press the buttonuntil the LED on the remote stops flashing.To disarm the vehicle, press the buttonuntil the LED on the remote stops flashing. If pressing the arm/disarm buttons does not arm/disarm the vehicle, youwill need to release the button and try again, as the remote stops transmitting assoon as the LED stops flashing.Press the buttons for a 1/2 second to mute the vehicle horn or sirenwhen arming or disarming your vehicle. Keep in mind that your horn/siren will stillactivate for all other modes (i.e. panic or alarm trigger) regardless of whether or notyour horn/siren is in mute mode. The horn/siren will be mute only when arming ordisarming your vehicle. When the alarm is armed, the starter kill function (an optional feature provided byyour installer) is activated. This feature disengages the starter mechanism on yourvehicle and prevents it from starting, even with a key.Step1:Activate Valet/ Programming mode by manually turning the ignition on and off five times with the key within a 7 second period.The parking lights will flash once with successful completion of this step.Page 7Auto-Start Function Press the button for 2 seconds to auto-start an automatic transmissionengine. Remember, that an actual key in the ignition is required to drive the car. For manual transmission vehicles, please use reservation mode.Press the button for 2 seconds in order to turn off an auto-started car.The engine will run 15 or 25 minutes (25 or 45 min for diesel) depending on presetoptions at the time of installation, and then shut off.1234567Error Number(# of times the car chirps & parking lights flash)Error ReasonEngine OnKey OnDoor OpenTrunk OpenBrake On Hood OpenReservation Off (Manual Transmission Only)If there is a problem in auto-starting your vehicle,the Young Shin Electronics, Incsystem will do one of two things ; if it fails for any of the reasons listed in the tablebelow, it will flash the parkinglights three times then flash the error number.Otherwise, it will attempt to start the vehicle three times. If, after three times, thevehicle will not start or stay running, the Young Shin Electronics, Inc. system willshut down. In either case, please see your istaller to resolve the situation.Note :If you lose your remote after you have armed the vehicle, use your keyto open the door. The siren will go off. Turn the ignition on then off, 5 times with your key to shut down the alarm and put the system into valet mode. You can cancel the valet mode with a remote later on. See : Valet mode, on page 10. Note : Siren duration is 30 to 60 seconds depending on the options set at the time of initial installation.
When the vehicle shuts off after reservation mode, the Young Shin Electronics, Inc system will lock/arm the vehicle. Take care to not lock your keys inside.If you try to auto-start the vehicle when reservation mode hasnot been set, the auto-start feature will not work. When you press the auto-start button, the car parking lights will flash three times,pause, then flash seven times.Page 9•If you do not want to set reservation mode, shut off the engine before you exit the vehicle. The engine will shut off for the following reasons : You did not activate the parking brake or pressed the foot brake when you turned the manual key to the off position. You released the parking brake while the engine was running. You entered Valet Mode after the Reservation Mode has been completed. Trunk ReleasePress the button until the LED on the remote stops flashing, in order to unlockand release your trunk door. If pressing the trunk release button does not releasethe trunk, you will need to release the button and try again, as the remote stopstransmitting as soon as the LED stops flashing.Note that the trunk release function will not only release the trunk but will unlock theall doors as well. Important!Important!Panic Mode Press the button for 3.5 seconds to enter Panic Mode. In this mode, the car will arm, if not armed already, and the siren/horn will activate and the parking lights will flash.In order to disengage Panic Mode, press the button until the LED stops flashing.Then, press the button for a 1/2 second to unlock/ disarm your vehicle. Your vehicle is now ready for auto-starting. However, the reservation mode will be cancelled if a door or hatch is opened, or if the Scosche system is put in Valet mode.Once cancelled, you will have to start the vehicle with the key and repeat the above 5 steps if you want to restore reservation mode.In order to auto-start your manual transmission vehicle, you must first set the Young ShinElectronics, Inc. system to Reservation Mode before leaving your vehicle. The purpose ofReservation Mode is to leave the transmission gear in the neutral position when you leaveyour vehicle. Reservation mode is intended for use on MANUAL TRANSMISSIONS ONLY and NOT FOR AUTOMATIC TRANSMISSIONS. Reservation Mode must be engagedeach and every time you leave your manual transmission vehicle in order to auto-start it.Note : The system is not recommended for manual transmission vehicles with removable or convertible tops. •The transmission must be in the NEUTRAL position. The vehicle windows must be rolled up. Do not set the reservation mode with people in the vehicle. Do not auto-start the vehicle with people inside it. •Step1 : After arriving at your destination, and BEFORE TURNING YOUR ENGINE OFF, place the transmission in the Neutral position.Step2 : Activate the parking brake.Step3 : Remove your foot from the foot brake.Step4 : Remove the key from the ignition, and the engine will remain running.Step5 : Exit the vehicle and close the door within two minutes after activating the parking brake. The engine will shut off and reservation mode for the remote starter is now complete.Page 8Reservation Mode (manual transmission only)The anti-grind circuit (an optional feature provided by your installer) preventsyou from engaging the starter on a remote-started vehicle.While your vehicle is running with your key, press the button for 2 seconds, you are now in the continuation mode. Your engine will continue running for thepreset time even if you take your key out of the ignition. You can now lock/arm thevehicle if you wish to.For a quick stop when you don’t want to restart the vehicle.
Timer Start Mode In Timer Start Mode, your car automatically starts every 1.5 or 3.0 hours, depending on preset options during the time of installation, for a 24-hour period. This mode is cancelled automatically after 24 hours or once you start your vehicle with the key or remote. In orderto enter Timer Start Mode, press the buttons simultaneously for a 1/2 second. Please note : Timer Start Mode becomes once an optional temperature sensor is installed. Important!Timer Start Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such asa garage or carport.Page 10Valet Mode While the vehicle is in valet mode, the only features that will function will be the keyless entry and optional auxiliary functions.In order to enter Valet mode, press the buttons simultaneously for a 1/2second. In order to manually enter Valet Mode, insert your key into the ignition and turn the ignition on and off five times within 7 secondsYou can exit Valet Mode only by pressing buttons simultaneously for 1/2 second.If the Anti-Jacking option has been programmed (ask your dealer if you would liketo have this option) and the Ignition-Kill has been installed , the Panic Mode worksas Anti-Jacking if the key is in the ignition. If Anti-Jacking mode is activated while keyis in the ignition, a) the siren will go off for 1.5 minutes, and b) the Ignition-Killwill be activated after the first 30 seconds. This is to give a 30 second warning to the hijacker, then to disconnect the ignition to stop the vehicle.Page 11Safety Shut Down FeaturesThe Young Shin Electronics, Inc R1800 system has several shut down safety features. The following actions will shut down the engine or prevent the car fromauto-starting : Opening the hood, pressing the brake, or if valet mode is turned on.OPTIONAL PROGRAMMABLE FEATURESIgnition LockThese additional features may be programmed to the Young Shin Electronics, Inc.system by your authorized Young Shin Electronics, Inc dealer. This progammable option will automatically lock the vehicle doors once the key is in the ignition and the brake pedal is pressed. The doors will unlock as soon as the key isremoved from the ignition.This progammable option will automatically lock the vehicle doors once the key is in the ignition and the brake pedal is pressed. The doors will automatically unlock when the emergency brake is set while the vehicle is running with the key.Passive LockingYou can turn this function on or off by pressing the buttons for a 1/2 second. When set to passive locking, your system will lock automatically, 30 secondsafter all the doors/ hatch have been closed. Turbo Mode you can turn this feature on and off by pressing Buttons for a 1/2second .
Page 12Cold Start Mode OPTIONAL INSTALLATION FEATURESThe Young Shin Electronics, Inc R1800 remote has additional features andexpansion possibilities that require additional parts and labor. Timer Start Modebecomes Cold Start Mode. In this mode, your car automatically starts if the temper-ature of the inside of the vehicle goes below the preset temperature. The minimum interval between the starts will be 1.5 or 3.0 hours depending on preset options during the time of installation. Cold Start Mode is activated or deactivated by pressing Buttons for a 1/2 second.Optional Auxiliary 1 & Auxiliary 2The auxiliary system is an optional feature that can be tailored for your vehicleby your local authorized Young Shin Electronics, Inc dealership. For example, youcan customize your car to have remote power control of your windows, radio, andsunroof in addition to the rooftop on your convertible car.In this mode, if the emergency brake has been engaged, the engine will continue to runafter the key has been taken out of the ignition. It will run until two minutes after the emergency brake has been set.To utilize this mode, the emergency brake sensing wire has to be connected to the emergency brake wire of the vehicle. Consult the authorized dealer for this mode.This option is ideal for turbo charged vehicles because it allows the turbo to cool down after operation.

Navigation menu