Youngshin Electronics JR200AMEN Car Alarm System User Manual M861AR200 FCC ID

Youngshin Electronics Co., LTD. Car Alarm System M861AR200 FCC ID

Users Manual

USER’S GUIDEBy Youngshin Electronics Co., Ltd.www.magicar.comFCC ID : O44JR200AMENThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.
User’s GUIDE TABLE OF CONTENTSSafety InformationRemote : R200Remote Button FunctionsRemote Learning RoutineKeyless EntryAlarm ModeTrunk ReleasePanic ModeValet ModeOptional Programmable FeaturesIgnition LockPassive LockingOptional Installation FeaturesDoor pulse DurationFlashing Signal LightAnti-jackingPage 4Page 4Page 5Page 5Page 6Page 6Page 7Page 7Page 7Page 8Page 8Page 8Page 8Page 8Page 8Page 8Page 3User’s GUIDE
The model name, R200 stands for One Way AM 4 Button Remote.Safety Information Please take these safety precautions into consideration, under the following conditions : Page 41. Servicing the vehicleWhen servicing your automobile (i.e. changing the oil, washing your car), the Magicar system should be in Valet Mode. 2. Loaning your vehicle to othersWhenever you loan your vehicle to an individual who is not familiar with Magicar, please put the vehicle in Valet mode. This will prevent the vehicle barrower from accidentally activating the Magicar auto-security system. Remote Page 5Remote Button Functions12345678910Lock0.5 sec0.5 sec0.5 sec0.5 secUnlockButton Press Function2 sec Panic, Press Lock to shut off Siren Valet Mode - on/offSiren Chirps for Lock /Unlock - on/off0.5 sec Ignition Lock - on/off0.5 sec Passive Arming - on/off0.5 sec Shock Sensor - on/off2 sec Trunk Release2 sec Programming Menu - Installer OnlyNote : ""Means pressing the button for 2 seconds."()"Means simultaneously pressing the buttons."()"Means simultaneously pressing the buttons for 2 seconds.Remote Learning RoutineThe Magicar will allow up to three remotes to be programmed to one vehicle.Please perform the following procedure to add or reprogram additional remotes.Step1:Activate Valet/ Programming mode by manually turning the ignition on and off three times (between Acc and On)with the key within a 7 second period.The parking lights will flash once with successful completion of this step.
You can exit Valet Mode only by pressing buttons simultaneously.To arm the vehicle, press the button .To disarm the vehicle, press the button. If pressing the arm/disarm buttons does not arm/disarm the vehicle, you will need torelease the button and try again, as the remote stops transmitting as soon as theLED stops flashing.Press the buttons for a 0.5 second to mute the vehicle siren when arming or disarming your vehicle. Keep in mind that your siren will still be activatedfor all other modes(i.e.panic or alarm trigger) regardless of whether or not your sirenis in mute mode. The siren will be mute only when arming or disarming your vehicle.When the alarm is armed, the starter kill function (an optional feature provided byyour installer) is activated. This feature disengages the starter mechanism on yourvehicle and prevents it from starting, even with a key.To lock the vehicle, pressing the button for a 0.5 second. To unlock the vehicle, press the button for a 0.5 second. If the pressing of thelock/unlock buttons does not lock/unlock the doors, you will need to release thebutton and try again, as the remote stops transmitting as soon as the LED stopsflashing. If the button is pressed for 2 seconds, it will panic the system.Page 7Keyless EntryAlarm ModePage 6Step2 :Within a 7 second period after cycling the ignition for the 3rd time,Press the button for a 0.5 second. The parking lights will flash once to confirm that the transmitter has been programmed. You can continue programming additional remotes. The parking lights will flash two times when the programming mode has expired.Note :If you lose your remote after you have armed the vehicle, use your key to open the door. The siren will go off. Turn the ignition on and off, 3 times with your key to shut down the alarm and put the system into valet mode. You can cancel valet mode with a remote later on. See: Valet mode, on page 7.Trunk ReleasePress the button for 2 seconds, in order to unlock and release your trunk door. If pressing the trunk release button does not release the trunk, you will need torelease the button and try again, as the remote stops transmitting as soon as theLED stops flashing.Note that the trunk release function will not only release the trunkbut will unlock the all doors as well.Panic Mode If Anti-Jacking option has been programmed (ask your dealer if you wouldlike to have this option) and the Ignition-Kill has been installed , Panic Mode works as Anti-Jacking if the car key in the ignition. In Anti-Jackingmode is activated while key is in the ignition,a) the Siren will go off for 1.5 minutes, and b) Ignition-Kill will be activated after the first 30 seconds. This is to give a 30 second warning to the hijacker, then to disconnect the ignition to stop the vehicle.Press the button for 2 seconds to enter Panic Mode. In this mode, the car will bearmed,if not armed already, and the siren will be activated and the parking lights will beflashed. In order to disengage Panic Mode, press the button.Then, press the button for a 0.5 second to unlock/ disarm your vehicle. Valet Mode While the vehicle is in valet mode, the only feature is the keyless entry and optional auxiliaryfunctions.In order to enter Valet mode, press the buttons simultaneously for a 0.5 sec-ond. In order to manually enter Valet Mode, insert your car key into the ignition and turn theignition on and off (between ACC and ON)three times within 7 seconds
Page 9Page 8OPTIONAL PROGRAMMABLE FEATURESIgnition LockThese additional features may be programmed to the Magicar system by yourauthorized Magicar dealer. This programmable option enables your vehicle to automatically lock the doors oncethe key is in the ignition for 30 Seconds.(Also you can lock the doors, If you step onthe brake pedal within 30 Seconds) In addition, the vehicle will automatically unlockthe doors when the key is pulled out of the ignition. Passive LockingYou can turn this function on or off by pressing the buttons for a 0.5 sec-ond. When setting to passive locking, your system will lock automatically 30 secondsafter all the car doors are closed. OPTIONAL INSTALLATION FEATURES- Door Lock/ Unlock, Pulse Duration:if you set this mode, Door Lock/UnlockPulse Duration will be changed 0.8 second to 4 seconds.- Flashing Signal Lights during Door Open: When you leave your car without closing the doors, the signal lights will flash.Anti-Jacking: It can be programmed to send a signal to a relay to disconnect the ignition wire of the vehicle upon anytime the vehicle is armed so that the vehicle cannot start or run by a remote or a key.And the running of vehicle can be shut off by remote’s panic command.Start-Kill : It can be programmed to send a signal to a relay to disconnect thestarter wire of the vehicle upon arming. Page 10Page 11Page 12Page 13Page 14Page 16Page 16Page 16Page 17Page 17Page 18Page 19Page 19INSTALLATION GUIDE TABLE OF CONTENTSINSTALLATION GUIDEInstallation Tips & RecommendationsR200 Wiring Digram CON 1CON 2 CON 3CON 4CON 5AntennaOption ModeProgramming Menu OptionHow to set OptionsCanceling(Going to Factory Default)Option ModeConfirmation of Wrong Programming. . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 10 Page 111-1. Please be careful not to lock yourself out.Please lower the glass windows before you start the installation in case the door lockswith the key inside. Also, learn the remote to the brain module after the installationhas been completed.1-2. Use Digital Multimeter for testingUse a Digital Multimeter for all testing of wires in the vehicle. This should be done on all wires even if you feel that you know exactly what they are and how they should test. Use of lamp tester may damage the electrical circuit of the vehicle. 1-3. Find Good GroundOne of the most important wire connections is the ground connection. Please find a spot that does not have any resistance to the battery ground. Improper ground will result in malfunction of the system.1-4. Make sure your installation does not become a driving hazard later to the driver.During installation process, please try to foresee there are any potential problemsto the driver later.Potential Driving Hazards There should be no wiring around the brake. Connection problem or Insulation problemPlease make sure all the connections are done by soldering and are properly insulated by electrical tape. Will any of your installation be affected by the vibration and engine heat during driving?Tie securely every components of your installation by use of bolts or cable tie. Be sure that engine heat will not damage any wiring inside of the engine compartment. Organizing wiring after the installationImproper wiring organization will result in electrical noise, connection problems, safety hazards. Installation Tips & RecommendationsUser’s familiarity with operating manualInstaller should thoroughly explain system operation to the user.1-5. Vehicle check-up prior to and after the installation.For your protection, check the vehicle inside and out including all of the vehicle operating conditions and various factory systems to make sure theywork properly after installation in the same manner as prior to the installation.AntennaM861A Wiring Digram
No 1 (Red) : (+)12V InputSolder this wire to the vehicle’s 12V constant. This wire must be supplied power all of the time and must be able to withstand high current draw.No 2 (Green/ White) : (+)Output for parking LightNo 3 (Brown) : (+)12V Siren OutputThe Black wire at the siren is to be chassis grounded. The siren volume can be reduced by cutting the volume wire attached to the siren.No 4 (Gray) : (+)12V Trunk OutputIf the vehicle is equipped with electrical trunk release, the trunk out isconnected to trigger the trunk solenoid. No 5 (Black) : Chassis GroundThis will be the one of the most important connections. Connect this wire to baremetal of the vehicle. We do not recommend using the steering column for a ground-ing point. Make sure you strip back the paint or use a factory grounding point. Bad grounding on this wire will be the beginning of future troubles. Page 12C0N1trunkSolenoidtrunk Release SwitchCON1-4C0N2Page 13< Circuit diagram >The Wires of CN2 are not connected with any part of insideConnect +12V to the wire placed between the Connector and the Fuse (20A)< Circuit diagram during unlock output >< Circuit diagram during lock output>Installers are able to install as per the following methods when you install, please find a suitable method as per the door system of your vehicleMethod 1 :Negative Trigger Door Lock System (W/O Actuator)-Method 2 : Positive Trigger Door Lock System(W/O Actuator)Positive parking light output.
Page 15No 2 (Blue) : Negative Starter-Kill Output Please use the pre-wired starter kill relay. Page 14No 1 (Green) : (+12V)Ignition InputThis wire will test (using your digital multi-meter) 0V with the key off, and 12V withthe key in the ‘ON or RUN’ ‘positionC0N387Relay8586 3087a CutStarterKey Cylinder Starter WireOFFACCONSTART.... Anti Jacking Mode ... 87Relay8586 3087a CutEngineKey CylinderIgnition WireOFFACCONSTART.... Starterkill Mode ... No 3 (Red/Black) : Negative Trigger Door Open SenseNo 4 (Red) : Positive Trigger Door Open Sense+12VCON3-3(-) Door TriggerDome LightDoorTrigger SW DoorTrigger SW+12VCON3-4(+) Door TriggerDome LightPlease make sure you have found a correct door sensing wire that monitors all doors. No 5 (Violet / Black ) : (-)Trunk Trigger Input.connect this to wire to the trunk lamp wire as shown belowNo6 (Light Blue / White) : (+) Brake Trigger InputConnect this wire to the foot Brake Wire as shown below. +12VCON3-6(+)Brake TriggerStop LampFoot Brake S/WCON 3-5(-)Trunk Trigger InputTrunk Lamp +12V< External Actuator>Method 3 : External Actuator
Page 16Options ModePress buttons and Simultaneously for 2 seconds in order to enterOption Mode.Note : "1. Door Lock/Unlock Pulse Duration : If you set this mode, Door Lock/Unlock Pulse Duration wil be changed 0.8 second to 4 seconds. 2. Start Kill Mode Anti-Jacking(Ignition-Kill) : The #2 wire of CON3 can be programmed to send a signal to a relay to disconnectthe ignition wire of the vehicle anytime the vehicle is armed so that the vehicle cannotstart or run by remote or key. The vehicle can also be shut off with remote by use ofthe panic command, even if it is running with a key in the ignition. Srarter-Kill : The #2 wire of CON3 can be programmed to send a signal to a relay to disconnectthe srarter wire of the vehicle upon arming. 3. Parking Light Flashing :With this option, the parking lights will flash if any door remains open while the vehi-cle is disarmed. Door Lock/Unlock Pulse Duration Application of Pre-wired Kill Relay Flashing Parking Light During Door Open0.8 Sec Starter KillDisabled4 SecAnti-jacking (IG-kill) ActivatedFeatures (Factory Default)Programming Menu OptionC0N4No 1 (Black) : GNDNo 2 (Black/White) : (+)LEDC0N 5Antenna} LED Ass’yNo 1 (Black) : GNDNo 2 (White) : (-)and stage shock InputNo 3 (Red) : (+12)No 4 (Yellow) :(-)1st stage shock InputPage 17}Dual stage shock sensorNo7 (Black /White) : (-) Input for optional SensorWhen installing additional sensors, use this wire as the input wire for those sensors.Always remember, when attaching more than one sensor to any input, you must diode iso-late them so that they don’t backfeed into each other.When Magicar systems are installed, please pay attention to stretch out the wire ofantenna. If the wire is bended or twisted seriously, it will be one of the reasons,which will reduce the receiving range.Antenna ModuleFCC ID: O44J1WAMLEDANT
EX ) When you would like to program Option 3 which is for Flashing parkingLight during door open1.Press button for 2 seconds (The siren and signal lights will chirp one time each)2.Press button three times (The siren and signal lights will chirp and flash one time whenever press button ) and wait for 5 seconds.You can only program one option at a time. You will have to repeat the procedure forevery option you would like to change.Step1: Press buttons for 2 seconds. The siren and signal lights will chirp and flash one time each. - If you fail to program, the siren and signal lights will chirp and flashthree times each.Step2: Press button the number of times to go to the option number you want to change.- The siren and signal lights will chirp and flash one time whenever you press button . Step3: Wait a few seconds. You will hear a number of chirps and see a numberof parking light flashes corresponding to the option number you want to change. If the number of chirps or flashes does not match the option number you want, wait 10 seconds, then start over at step 1.Step4: Press button or as you want to program the option. - If you press button , the option will be set to the default setting. The siren and signal lights will chirp and flash one time each. - If you press button , the option will be set to the optional setting. The siren and signal lights will chirp and flash two times each. 3.The siren and signal lights will chirp and flash three times after 5 seconds4.Press button after confirmation of the siren and signal lights as no. 3 (The siren and signal lights will chirp and flash two times each.)Page 18How to set Options+Page 19Canceling(Going to factory default)Option ModeStep1: Press buttons for 2 seconds (The siren and signal lights will chirp and flash one time each).- If you fail to program, the siren and lights will chirp and flash three times each.Step2: Press button three times. (The siren and signal lights will chirp and flash once time the button is pressed.)Step3: All options will be reset to factory defaults after the confirming 3 chirps and flashes. Confirmation of Wrong ProgrammingWhen you press the buttons incorrectly, Option Mode will not be programmed and the siren will activate for 1 second. ++

Navigation menu