Yuneec Technology CGO3 3-Axis Gimbal Camera User Manual CGO3 02

Yuneec Technology Co., Limited 3-Axis Gimbal Camera CGO3 02

Users Manual

CGO3 USER MANUALINTRODUCTIONCGO3 (available separately) is an innovave combinaon of 3-axis brushlessgimbal, camera and digital video downlink.The Self-Stabilizing gimbal makes it possible to capture amazing photographs andvideo footage for an array of uses. And the built-in digital video link deliversstreaming video to 5.8GHz WiFi compable iOS® and Android™ equipped devicesincluding smart-phones and tablets as well as YUNEEC Personal Ground Staons.OPERATING INSTRUCTIONS:(1) Insert the micro SD card into CGO3, plug in the power cord and slide the power switch, then     CGO3 start to work;(2) When the green light starts to flash , it indicates that wifi has started to work. At this me, you      can take device to connect to CGO3's wifi, when the device is connected, the light will grow      solid green.(3) Then press the shuer buon, CGO3 will take a picture; long press the shuer buon, CGO3       will enter recording funcon;(4) Toggle the switch ,then CGO3 will be powered off.OPERATION:(1) Plug the 3-Pin power cord into the appropriate socket head.(2) Install the gimbal under the belly of plane.(3) Power on the plane, then gimbal will work.FCC STATEMENT:This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protecon against harmful interference in a resi-denal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separaon between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is con-nected.This device complies with part 15 of the FCC rules. Operaon is subject to the following two condi-ons:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.  NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pro-tecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-ons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will  not occur  in a parcular installaon. If  this equipment does cause  harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separaon between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.—Consult the dealer or an experienced radio/TV technician for help.CAUTION: Any changes or modificaons not expressly approved by the party responsible for com-pliance could void the user's authority to operate this equipment. RF EXPOSURE WARNING• This equipment must be installed and operated in accordance with provided instrucons and the antenna(s) used for this transmier must be installed to provide a separaon distance of at least 20 cm from all persons and must not be co-located or operang in conjuncon with any other antenna or transmier. End-users and installers must be provide with antenna installaon instrucons and transmier operang condions for sasfying RF exposure compliance.IC RADIATION EXPOSURE STATEMENT FOR CANADAThis device complies with Industry Canada licence-exempt RSS standard(s).Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera-on of the device.Le  présent  appareil  est  conforme  aux  CNR  d'Industrie  Canada  applicables  aux  appareils  radio exempts de licence. L'exploitaon est autorisée aux deux condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter tout brouillage radioélec-trique subi, même si le brouillage est suscepble d'en compromere le fonconnement.This equipment complies  with IC RSS-102 radiaon exposure limit set forth for an uncontrolled environment.Cet équipement respecte les limites d'exposion aux rayonnements IC définies pour un environne-ment non contrôlé
CGO3 USER MANUALINTRODUCTIONCGO3 (available separately) is an innovave combinaon of 3-axis brushlessgimbal, camera and digital video downlink.The Self-Stabilizing gimbal makes it possible to capture amazing photographs andvideo footage for an array of uses. And the built-in digital video link deliversstreaming video to 5.8GHz WiFi compable iOS® and Android™ equipped devicesincluding smart-phones and tablets as well as YUNEEC Personal Ground Staons.OPERATING INSTRUCTIONS:(1) Insert the micro SD card into CGO3, plug in the power cord and slide the power switch, then     CGO3 start to work;(2) When the green light starts to flash , it indicates that wifi has started to work. At this me, you      can take device to connect to CGO3's wifi, when the device is connected, the light will grow      solid green.(3) Then press the shuer buon, CGO3 will take a picture; long press the shuer buon, CGO3       will enter recording funcon;(4) Toggle the switch ,then CGO3 will be powered off.OPERATION:(1) Plug the 3-Pin power cord into the appropriate socket head.(2) Install the gimbal under the belly of plane.(3) Power on the plane, then gimbal will work.FCC STATEMENT:This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protecon against harmful interference in a resi-denal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separaon between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is con-nected.This device complies with part 15 of the FCC rules. Operaon is subject to the following two condi-ons:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.  NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pro-tecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-ons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will  not occur  in a parcular installaon. If  this equipment does cause  harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separaon between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.—Consult the dealer or an experienced radio/TV technician for help.CAUTION: Any changes or modificaons not expressly approved by the party responsible for com-pliance could void the user's authority to operate this equipment. RF EXPOSURE WARNING• This equipment must be installed and operated in accordance with provided instrucons and the antenna(s) used for this transmier must be installed to provide a separaon distance of at least 20 cm from all persons and must not be co-located or operang in conjuncon with any other antenna or transmier. End-users and installers must be provide with antenna installaon instrucons and transmier operang condions for sasfying RF exposure compliance.IC RADIATION EXPOSURE STATEMENT FOR CANADAThis device complies with Industry Canada licence-exempt RSS standard(s).Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera-on of the device.Le  présent  appareil  est  conforme  aux  CNR  d'Industrie  Canada  applicables  aux  appareils  radio exempts de licence. L'exploitaon est autorisée aux deux condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter tout brouillage radioélec-trique subi, même si le brouillage est suscepble d'en compromere le fonconnement.This equipment complies  with IC RSS-102 radiaon exposure limit set forth for an uncontrolled environment.Cet équipement respecte les limites d'exposion aux rayonnements IC définies pour un environne-ment non contrôlé

Navigation menu