Yuneec Technology SR24 Radio Controller Receiver User Manual 20150324 v2

Download:
Mirror Download [FCC.gov]
Document ID	2564161
Application ID	1Msoxm3iyM7kNgeWeZfk7Q==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.49kB (506139 bits)
Date Submitted	2015-03-24 00:00:00
Date Available	2015-03-24 00:00:00
Creation Date	2015-03-24 16:45:46
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2015-03-24 16:45:46
Document Title	Microsoft Word - User Manual 20150324 v2
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

SR24 User Manual
Connecting SR24 to ST24
Plug the cable from FC0(flight control for THE AIRCRAFT) into SR24 socket, and power
on THE AIRCRAFT. Lean THE AIRCRAFT nose forward twice times, the BLUE LED of
SR24 will flash slowly, indicating the receiver ready for binding. When the binding between
SR24 and ST24 completes (see the following instructions of Binding THE AIRCRAFT
and ST24), the BLUE LED will be off. Turn on ST24, press FPV and press ‘Take off’.
Binding THE AIRCRAFT and ST24
z THE AIRCRAFT with gimbal, camera and LINK58
Push the POWER Switch to the left side and Power on ST24→Keep THE AIRCRAFT
nose to north, and power on THE AIRCRAFT as the arrow shows →Wait until THE
AIRCRAFT completes self-inspection, and BLUE LED flashes→ Hold THE AIRCRAFT tail
and lean the copter forward twice, and YELLOW LED flashes →Press ‘PAD’ →Press
‘Settings’ and find WiFi signal of LINK58, choose it and enter the password, press
‘Connect’, it will show “Connected”→Press
twice and back to the main interface
→Press ‘FPV’ on the main screen of ST24 →Press ‘System Settings’ →Press ‘Refresh’
→Choose your Model and Camera →Press ‘Bind’ →Press
→Press ‘Take Off’ and
you will hear 2 beeps,
z Lack anyone of gimbal, camera or LINK58
Push the POWER Switch to the left side and Power on ST24→Keep THE AIRCRAFT
nose to north, and power on THE AIRCRAFT as the arrow shows →Wait until THE
AIRCRAFT completes self-inspection, and BLUE LED flashes→ Hold THE AIRCRAFT tail
and lean the copter forward twice, and YELLOW LED flashes →Press RC → Press
‘system settings’ →Press ‘Refresh’ →Choose your receiver’s code of THE
AIRCRAFT→Press ‘Bind’ →Press
→Press ‘Ready’ and you will hear 2 beeps
Antenna
Socket for gimbal
Socket for FC0
SR24 YELLOW LED Status
Three statuses for SR24 BLUE LED: solid, fast flash, slow flash.
-Solid YELLOW LED indicates the receiver is ready to bind;
-Fast flash YELLOW LED indicates SR24 is connected with the transmitter;
-Slow flash YELLOW LED indicates SR24 is disconnected with the transmitter.
FCC Statement:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
(1) Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment. (2) The modules FCC ID and IC ID are not visible when
installed in the host, or (3) If the host is marketed so that end users do not have straight forward
commonly used methods for access to remove the module so that the FCC ID and IC ID of the module is
visible; then an additional permanent label referring to the enclosed module: Contains Transmitter
Module FCC ID:2ACS5-SR24; IC: 11554B-SR24 or Contains FCC ID:2ACS5-SR24; IC: 11554B-SR24
must be used.
RF exposure warning
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment must be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provided with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure compliance.
IC Radiation Exposure Statement for Canada
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Information for the OEMs and Integrators
This device is intended for OEM integrators only.
Please See the full Grant of Equipment document for other restrictions.
Information To Be Supplied to the End User by the OEM or Integrator
The following regulatory and safety notices must be published in documentation supplied to the end user of the product or
system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains FCCID:
2ACS5-SR24“, FCC ID displayed on label.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2015:03:24 16:45:46+08:00
Create Date                     : 2015:03:24 16:45:46+08:00
Format                          : application/pdf
Title                           : Microsoft Word - User Manual 20150324 v2
Creator                         : Administrator
Document ID                     : uuid:770851a9-30df-451c-9fd0-806851fde23a
Instance ID                     : uuid:180a8d12-57a6-45fe-bf1c-97c753e505d3
Page Count                      : 4
Author                          : Administrator

EXIF Metadata provided by EXIF.tools