Yunlink Technology P48 Outdoor Access Point User Manual HWAP80 P48

Download:
Mirror Download [FCC.gov]
Document ID	3790482
Application ID	FPB5jxZa3bJ05E9oqKv5/g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	236.48kB (2956019 bits)
Date Submitted	2018-03-21 00:00:00
Date Available	2018-03-21 00:00:00
Creation Date	2018-03-14 15:32:24
Document Lastmod	2018-03-14 15:32:59
Document Title	HWAP80-P48 英文说明书
Document Creator	Doro PDF Writer [2.11] [http://www.the-sz.com/]

User Manual of 11ac 1200Mbps Outdoor Access
Point :HWAP80-P48
This is the user manual of 11ac 1200Mbps Outdoor Access Point, which will approximate guide you how to set and
apply the Outdoor Access Point, it provide a convenient graphical interface for network construction and maintenance
person, as well as a user through a simple and accurate operation, and configuration management of the ceiling
wireless access point.
1 s t Hardware Instruction
AP Setup
AP Interface:
RST: Reset Button, it make AP revert to default data after press it 15 seconds.
WAN/PoE: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Outdoor Access
Point and WiFi Repeater operation mode.
SMA Connector: have 2.4G and 5.8G, connect with 2.4G or 5.8G antenna.
2 n d ： Login
）Connect the Outdoor Access Point with computer
2）Configure the PC’s local connection IP address as 192.168.188.X (X is number from 2 to 254),
255.255.255.0, follow P4 and P5 to finish.
P4
Setting of computer’s IP address
subnet mask is
P5
Setting of computer’s IP address
3) Input 192.168.188.253 into IE browser, then pop up the login page, the default login user name: Admin,
Passwords: admin, pls do following P6
P6 Login
3rd : WEB GUI interface Setting:
1) Status
After login, then P7 Device Status will be showed:
P7: Device Status
In this ceiling Outdoor Access Point, the default operation mode is AP mode.
Then in 2.4G Wireless Setting, GUI configuration page showed as below:
User can configure the SSID, password, band width, channel here, then Apply to finish.
P8. 2.4G Wireless setting
5.8G Wireless Setting GUI configuration setting showed as P8:
P9
5.8G Wireless Setting
LAN Setting to configure the DHCP or Fix IP
P10 LAN Setting
AP location setting: can mark where the AP set up, and AP name as P11:
P11 AP Postion setting
2) Wizard Configuration:
Click Wizard in Status page, will pop up following page to configure the operation mode:
There are four operation mode of this ceiling Outdoor Access Point, and there are explanation for each operation mode
for better application.
P12 Operation mode
1. Gateway Mode:
Click Gateway mode, will pop up following pictures:
Pls choose the right WAN setting mode, then click next to continue.
P13. WAN setting in Gateway Mode
P14 Wireless Setting in Gateway Mode
When click Next, then will complete the Gateway mode setting and show following picture:
P15
Complete the setting in Gateway Mode
When return to Status, the page showed as follow:
P16 Status in Gateway Mode
2. WiFi Repeater mode
Click WiFi Repeater operation mode in Wizard, then following page will pop up, and choose the right SSID to bridge,
then next.
P17 Repeater Mode
After click Next button, then should configure the wireless settig as follow, then click Next to finish:
P18 Wireless Setting in Repeater Mode
Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure this
data in this page if required.
P19 Status in Repeater Mode
Pls note, when click wireless relay setting, following page will pop up, you can make change from here easy:
P20 Wireless Relay Setting
3. WISP Operation mode:
Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based on
the stepes showed in picture:
P21 WISP Mode
Configure the right WAN setting in WISP operation mode, then next.
P22 WAN setting in WISP mode
Configure wireless data showed as follow:
P23 Wireless Setting in WISP mode
Then complete and back to status, will show the connection fail or success, then can configure the data based on
request:
P24 Status in WISP mode
Remark: When click WAN Setting, will pop up following picture:
P25 WAN setting in WISP mode
4. AP Operation mode:
Set the wireless data, AP Location info as required, then click next to continue and enter into LAN setting.
After LAN setting, complete the AP mode configuration and back to Status:
P26 Wireless setting in AP Mode
P27 LAN Setting in AP Mode
P28 Status in AP Mode
3) Advanced Setting:
In advanced setting, user can check the Outdoor Access Point’s firmware version, working status, 2.4G wireless, 5.8G
Wireless, LAN Status,
upgrade firmware, Reset...
Let’s Click Advanced Setting in status page, will show return home, Setup Wizard which we showed before.
Let’s shown mode in Device Status, 2.4G Wireless, 5.8G Wireless, Network and Management.
P29 Device Status
Device Status: In this page, mainly to check the Outdoor Access Point’s status in firmware version, 2,4G Wireless,
5.8G Wireless and LAN status:
P30 2.4G Wireless Status
P31 5.8G Wireless Status
P32 LAN Status
2.4G Wireless Setting:
In this part, will show the 2.4G Basic Setting, Virtual AP, Access control and Advanced Setting:
P33 Basic Setting in 2.4G Wireless
2G Wireless Analyzer: Mainly to analyze the AP’s singal strength in some channel, to make user more easy to choose
the right channel
and avoid the wifi interface.
P34 Wireless Analyzer
Virtural AP:
There are 3 virtural AP in 2.4G wireless, if need virtural SSID, then users can configure it showed in following picture:
P35 Virtual AP
2.4G Access Control: Mainly show MAC allow or deny:
P36 MAC Access Control
2.4G Advanced Settings:
In this page, will show the regional, RF Power, Max user access...
P37 Advanced Setting
5.8G Wireless Setting: Almost same as 2.4G Wireless:
P38 5.8G Wireless Setting
Network setting:
In this page, mainly to show the LAN setting and VLAN as follow:
P39 Network Setting
P40 Tag VLAN Setting
Management:
In this part, show the system time, Logs, upgrade firmware, system, user info.
And we show System time, how to upgrade firmware and system page to users:
P41 System Time
P42 Firmware Upgrade
P43 System info
4th Share Internet and Obtain IP address automatically
Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as
following picture showed.
the computer will obtain the IP address from router or base station to get Internet.
Tr o u b l e S h o o t i n g :
F1
The Failure phenomenon and solution
Failure phenomenon
SYS Indicator off
Solution
Pls make sure the PoE module connection is right. POE Port
connect with AP, LAN port connect with computer
Pls check the IP address of computer and Outdoor Access Point to
see whether they are in same networking segment, The method is
click “start”-“Run” input“cmd” ping 192.168.188.253 to test the
Outdoor Access Point connectivity.
Reset Outdoor Access Point and load it again;
Pls make sure the IP address 192.168.188.253 is not occupied by
other device in Outdoor Access Point’s networking;
Check computer and cable problem, recommend to use 10/100M
UTP unshielded cable;
Clean up Arp binding from “Start”-“Run” input“cmd” arp –d
Clean the IE Brower’s temporary files and Cache file
Try to scan the avaliable wireless networking again
Make sure the Outdoor Access Point’s wireless standard 11b/g/n,
2.4G is correct
The Security and passwords are matched between Outdoor Access
Point and AP
The signal strength of AP is too weak to connect, should be more
than -75dBm
Scan it several times more
Make sure there are 5G signal existed.
Reset the Outdoor Access Point, scan it again after Outdoor Access
Point restart
Pls Check the computer’s IP address and DNS setting. If it is
dynamin, set the network card as automatically obtain. If it is static
IP, pls contact with ISP for correct IP address and DNS address.
Press the “Reset” button more than 15 seconds after power on. The
Outdoor Access Point will restore factory default after the Outdoor
Access Point restart.
，
Can’t land to Outdoor Access Point
through Web page
。
；
Outdoor Access Point can’t connect with
AP
the status display unconnected
（
）
Can’t scan the Outdoor Access Point
The connection of Outdoor Access Point
and AP is success, but the computer can’t
share internet
How to Reset Outdoor Access Point
）
；
；
；
；
；
（
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note 1: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note 2: 1.Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. The minimum separation generally be used is at least 20 cm.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2018:03:14 15:32:24+08:00
Creator Tool                    : Doro PDF Writer [2.11] [http://www.the-sz.com/]
Modify Date                     : 2018:03:14 15:32:59+08:00
Metadata Date                   : 2018:03:14 15:32:59+08:00
Format                          : application/pdf
Description                     : HWAP80-P48 英文说明书
Creator                         : 
Title                           : HWAP80-P48 英文说明书
Producer                        : 
Document ID                     : uuid:1c7f7270-ad51-4bd7-98d2-51b6e3527877
Instance ID                     : uuid:b1147602-e25d-4ac7-85a0-eb630c6fa9dc
Page Count                      : 27
Subject                         : HWAP80-P48 英文说明书
Author                          : 
Keywords                        : HWAP80-P48, 英文说明书

EXIF Metadata provided by EXIF.tools