Yunmai Technology M1805 YUNMAI Smart Scale User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4076773
Application ID	xaz8hoxx6Wf3ng5MO2jRXg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	49.63kB (620418 bits)
Date Submitted	2018-11-19 00:00:00
Date Available	2018-11-19 00:00:00
Creation Date	2018-11-16 12:05:48
Document Lastmod	2018-11-16 14:20:43
Document Title	User Manual
Document Creator	WPS 文字
Document Author:	yunmai_android

Do not disassmeble, squeeze, puncture the product or put it into water,
fire, or exposes it to temperature higher than 60℃ (140℉)
Important Notice:
YUNMAI Smart Scale should not be used to diagnose or treat any
medical situation.
Notice before Use
* Please ingore the first weighing reading at your first time use or after
move the scale.
* After scale power on or reset, please wait for the LED display flash
"0.0" for several seconds, and then start your weight-in.
* After each move of the scale, please wait for 5 seconds for the sensor
to self-recalibarate with the floor, and then weight for accurate reading.
Statement:
Weighing Notice
* Do not weight when charging battery.
* The scale surface may become slippery in humid places, please watch
your steps and don't slip during weighing.
* "weighing before meal or before bath" is the most recommend time
for weighing, because eating and bathing may affect the body moisture
and temperature, which might affect the sensor accuracy.
* Recommend to weigh yourself at the same time and same condition in
each day for more accurate data record.
Maintenance
* Use a damp cloth to wipe the surface of the scale
* Do not use any detergent to clean the scale, because detergent might
damage the electrodes which may affect the accuracy of detecting body
fat data.
Products Instruction and Installation
Thank you for choosing YUNMAI Smart Scale.
(1) Note: Charging port. Plug the charge cable into the charging port to
recharge the battery.
(2) Note: Power Switch. Press the button down to power on.
1. Install the YUNMAI APP
2. Start Using
Correct Standing Posture
Make sure your feet placement and standing posture is correct as shown
below:
（1）Remarks : LED on: Charging
LED flash: Low Power
3. YUNMAI APP
Download YUNMAI APP to use together with YUNMAI S scale, you can
record, analyze and set goals for your personal health.
YUNMAI saves all your information to cloud and provides brief health
reports and improvement recommendations.
FCC Statement
FCC ID: 2ADEB-M1805
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonabl e protection against harmful inte「ference
。
in a residential installati n. This equipment generates uses and can radiate
。
radio frequency energy and, if not installed and used In ace rdanca with the
ins甘uctions, rr咀y cause harmful interference to radio communications. However,
。
there is no gua 用ntee that interference will not occur in a particular installatl n
If this equipm制t d创始cause hannful interferen<万to radio or television r自沟以ion,
which can be determined by turning the equipment o仔and on, the user is
enCQuraged to try to corr，创t the inte厅e「ence by one or more of the following
measures·
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
( 1 )This device may not cause harmful interference.
(2）刊is device must accept any interference received, including interterence
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Material : Tempered Glass (Panel)+ ABS&PS (Bottom Cover)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : yunmai_android
Comments                        : 
Company                         : 
Create Date                     : 2018:11:16 12:05:48+04:00
Modify Date                     : 2018:11:16 14:20:43+08:00
Source Modified                 : D:20181116120548+04'05'
Subject                         : 
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Creator Tool                    : WPS 文字
Metadata Date                   : 2018:11:16 14:20:43+08:00
Keywords                        : 
Producer                        : 
Format                          : application/pdf
Creator                         : yunmai_android
Description                     : 
Title                           : 
Document ID                     : xmp.d
Instance ID                     : uuid:a168bfd3-77f2-4cb7-aec9-87865030cbae
History Action                  : editedScannedDoc
History When                    : 2018:11:16 14:20:43+08:00
History Parameters              : Page:8
Page Count                      : 9

EXIF Metadata provided by EXIF.tools