Z Com 0XG650 54Mbps Wireless Mini PCI Adapter User Manual XG 650 Maunal 930225

Z Com Inc 54Mbps Wireless Mini PCI Adapter XG 650 Maunal 930225

Contents

OEM installers manual

FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.
54Mbps IEEE802.11g Wireless Network Mini PCI Adapter complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional radiator
shall caution the user that changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To comply with FCC RF exposure compliance requirements, a separation distance of at
least 20 cm must be maintained between the antenna of this device and all persons.
This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and
users. The transmitter module may not be co-located with any other transmitter or
antenna. As long as the 2 conditions above are met, further transmitter testing will not
be required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be
installed such that 20 cm may be maintained between the antenna and users (for
example access points, routers, wireless ASDL modems and similar equipment). The
final end product must be labeled in a visible area with the following: "Contains TX FCC
ID:M4Y-0XG650 ".
RF Exposure Manual Information That Must be Included
The users manual for end users must include the following information in a prominent
location "IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter."
Additional Information That Must be Provided to OEM Integrators
The end user should NOT be provided any instructions on how to remove or install the
device.
Service Center in U.S.A
Company Name : Zcomax.
Company Address:14545 Valley View Ave., Suite S Santa Fe Springs, CA 90670
Tel:562-926-4588
1. Introduction
54Mbps IEEE802.11g Wireless Network Mini PCI Adapter is the perfect solution for your
wireless network applications based on the IEEE 802.11g standard offering a data rate
of 54Mbps in a wireless LAN environment.
XG-650 is designed for Access Point, Router gives you wireless access the web and
network resource without the wire.
XG-650 provides high-speed access to network resources and has built-in 40/64-bit,
128 bit and 256 bit of WEP (Wired Equivalent Privacy) data encryption. With Direct
Spread Spectrum Signaling (DSSS) and Orthogonal Frequency Division Multiplexing
(OFDM), domain access control, WEP encryption and group security, the modules will
safeguard all your wireless data transmissions from your nosy neighbors.
XG-650 allows you to take full advantage of your devices mobility with access to
real-time information and online services anytime and anywhere.
2. Feature
. Complies with IEEE 802.11b/g Standard for 2.4GHz Wireless LAN.
. Works with All Existing Network Infrastructures.
. Compatible with Wi-Fi Wireless Products and Services
. Capable of up to 256-Bit WEP Encryption.
. Freedom to Roam While staying Connected
. 54 Mbps High-Speed Transfer Rate
. Two UF-L Connectors for External Antenna
. Support Antenna diversity for Better Sensitivity
. Lower Power Consumption.
3. Specification
HOST INTERFACE
33MHz, 32-bit MiniPCI, Type III B (support TI VLYNQ bus)
RADIO
Chipset TI TNETW1130 ; Radia RC2422B & RC2326
Antenna Two UFL Connectors
USA (FCC) 11 Channels: 2.412GHz~2.462GHz
Europe (ETSI) 13 Channels : 2.412GHz~2.472GHz
Frequency
Japan (TELEC) 14 Channels : 2.412GHz~2.483GHz (14th ch only for
11b)
11g / 11g+ :OFDM (64QAM, 16QAM, QPSK, BPSK) Modulation 11b: DSSS (CCK, DQPSK, DBPSK) / 11b+: PBCC
11g / 11g+ : 64QAM 13dBm Typical Output Power 11b: DBPSK,DQPSK,CCK 17dBm Typical
11g / 11g+ : 54Mbps OFDM < -65dBm Receive Sensitivity
11b+: 22Mbps PBCC, <-80dBm
11g / 11g+ : mode: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Data Rate
11b mode: 11, 5.5, 2, 1 Mbps
11g / 11g+ : TX:650mA ; RX: 500mA (max) Power Consumption
11b: TX: 650mA ; RX: 500mA (max)
Voltage 3.3V + 5%
PHYSICAL SPECIFICATIONS
Dimension 59.60mm(L)*44.45mm(W)*3.25mm(H)
Weight <15g
ENVIRONMENTAL SPECIFICATIONS
Temperature (Ambient) Humidity
(non-condensing)
Operating 0~55℃ 90%
Storage -10~65℃ 5~95%
4. Hardware Installation
The following sections in this chapter describe how to install XG-650 Module
4.1. Installation Overview
XG-650 wireless module is design for Access Point and Router only.
4.2. Safety Recommendations
The safety guidelines are as follows:
λ Keep the board area clear and dust-free before, during, and after installation.
λ Keep tools away from walk areas where you and others could fall over them.
λ Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains, that
could get caught in the board.
λ Wear safety glasses if you are working under any conditions that might be
hazardous to your eyes.
λ Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe.
λ Never attempt to lift an object that is too heavy for one person to handle.
4.3. Maintaining Safety with Electricity
Warning: Before working on a board or working near power supplies, unplug the power
cord on AC units; on DC units, disconnect the power at the circuit breaker.
Follow these guidelines when working on equipment powered by electricity:
λ Do not work alone if potentially hazardous conditions exist anywhere in your work
space.
λ Never assume that power is disconnected from a circuit; always check the circuit,
extension cables, frayed power cords, and missing safety grounds.
λ If an electrical accident occurs, proceed as follows:
– Use caution; do not become a victim yourself.
– Disconnect power from the system.
– If possible, send another person to get medical aid. Otherwise, assess the
condition of the victim and then call for help.
– Determine if the person needs rescue breathing or external cardiac compressions;
then take appropriate action.
4.4. Installing a XG-650
λ Remove the XG-650 module from its protective packaging.
λ Avoiding Electrostatic Discharge
Before you install the XG-650 module, ground yourself by touching a piece of metal to
avoid electrostatic discharge (ESD). You should also take the following precautions to
prevent damage to the XG-650 module:
λ Keep the XG-650 module in its antistatic-shielded bag until you are ready to install
it.
λ Handle the XG-650 module by its edges.
λ Ensure the connector is connected to above Model’s board tightly.

Navigation menu