Z Com XG-630 IEEE 802.11b/g Mini PCI Card User Manual C XG 630 User Maunal 060210

Download:
Mirror Download [FCC.gov]
Document ID	709519
Application ID	fBQW12vHAYnSUaaDHtqbig==
Document Description	Uers Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.64kB (120490 bits)
Date Submitted	2006-09-26 00:00:00
Date Available	2006-09-26 00:00:00
Creation Date	2006-08-22 16:56:46
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2006-09-25 10:30:16
Document Title	Microsoft Word - C_XG-630_User Maunal_060210.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	queenlin

FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the
user that changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm
must be maintained between the antenna of this device and all persons.
This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users. For
laptop installations, the antenna must be installed to ensure that the proper spacing is maintained
in the event the users places the device in their lap during use (i.e. positioning of antennas must be
placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user
places the device in their lap for use) and The transmitter module may not be co-located with any
other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing
will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be installed
such that 20 cm may be maintained between the antenna and users (for example access points,
routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final
end product must be labeled in a visible area with the following: "Contains TX FCC ID:M4Y-XG-630
".
RF Exposure Manual Information That Must be Included
The users manual for end users must include the following information in a prominent location
"IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or
transmitter."
Additional Information That Must be Provided to OEM Integrators
The end user should NOT be provided any instructions on how to remove or install the device.
Service Center in U.S.A
Company Name : Zcomax.
Company Address:14545 Valley View Ave., Suite S Santa Fe Springs, CA 90670
Tel:562-926-4588
1. Introduction
54Mbps IEEE802.11g Wireless Network Mini PCI Adapter is the perfect solution for your wireless network
applications based on the IEEE 802.11g standard offering a data rate of 54Mbps in a wireless LAN
environment.
XG-630 is designed for Access Point, Router, ATUR, Printer Server series, IP Camera series and
Internet Video Server gives you wireless access the web and network resource without the wire.
XG-630 provides high-speed access to network resources and has built-in 40/64-bit, 128 bit and 256
bit of WEP (Wired Equivalent Privacy) data encryption. With Direct Spread Spectrum Signaling
(DSSS) and Orthogonal Frequency Division Multiplexing (OFDM), domain access control, WEP
encryption and group security, the modules will safeguard all your wireless data transmissions from
your nosy neighbors.
XG-630 allows you to take full advantage of your devices mobility with access to real-time
information and online services anytime and anywhere.
2. Feature
Complies with IEEE 802.11b/g Standard for 2.4GHz Wireless LAN.
Works with All Existing Network Infrastructures.
Compatible with Wi-Fi Wireless Products and Services
Capable of up to 256-Bit WEP Encryption.
Freedom to Roam While staying Connected
54 Mbps High-Speed Transfer Rate
Two UF-L Connectors for External Antenna
Support Antenna diversity for Better Sensitivity
Lower Power Consumption.
3. Specification
XG-630 802.11b/g WLAN Mini PCI Card
Product Description
IEEE 802.11b/g 2.4 GHz WLAN miniPCI card
Host Interface
32-bit miniPCI
Operating Voltage
DC3.3V ± 5%
Chipset
Mac/BB Processor
RF Chip
WINBOND W89C33DG
AIROHA AL2230
Power Consumption
11b
11g
TX: < 450mA
TX: < 450 mA
RX: ≦
RX: ≦
400 mA
400 mA
Radio
Antenna
Output Power
(Average)
one U.FL-R-SMT connectors
IEEE 802.11b:
16 dBm (± 1.5dB) @ 1/2/5.5/11Mbps
IEEE 802.11g:
13 dBm (± 1.5dB) @ 54Mbps
Sensitivity
IEEE 802.11g
IEEE 802.11b
Sensitivity @ Packet Error Rate: 10%
Sensitivity @ Packet Error Rate: 8%
♦
♦
♦
♦
♦
♦
♦
♦
Modulation
54Mbps:≦-65dBm
48Mbps:≦-66dBm
36Mbps:≦-70dBm
24Mbps:≦-74dBm
18Mbps:≦-77dBm
12Mbps:≦-79dBm
9Mbps:≦-81dBm
6Mbps:≦-82dBm
IEEE 802.11g (OFDM/DSSS)
♦
48/54 Mbps (QAM-64)
♦
24/36 Mbps (QAM-16)
♦
12/18 Mbps (QPSK)
♦
6/9 Mbps (BPSK)
IEEE 802.11b (DSSS)
5.5/11 Mbps (CCK)
♦
2 Mbps (DQPSK)
♦
1 Mbps (DBPSK)
♦
♦
♦
♦
♦
11Mbps:≦-80dBm
5.5Mbps:≦-83dBm
2Mbps:≦-84dBm
1Mbps:≦-87dBm
Operating
Frequency
IEEE 802.11b/g ISM Band
♦
USA(FCC): 2.412GHz ~ 2.462 GHz (CH1 ~ CH11)
♦
Europe(ETSI): 2.412 GHz ~ 2.472 GHz (CH1 ~ CH13)
♦
Japan(TELEC) : 2.412 GHz ~ 2.472 GHz (CH1 ~ CH13)
Software Specification
Supported OS Identical to Winbond Latest Version
Security
Identical to Winbond Latest Version
Physical Specification
Dimension
59.6mm(L) * 44.5mm(W) * 3.25mm(H)
Weight
≦ 50 g
Environment Specification
Operating
Storage
Warranty
12 months
Temperature (Ambient)
0 ~ 55 ℃
-20 ~ 80 ℃
Humidity (non-condensing)
90%
5 ~ 90%
4. Hardware Installation
The following sections in this chapter describe how to install XG-630 Module
4.1. Installation Overview
XG-630 wireless module is design for Access Point, Router, ATU-R, Printer Server series, IP Camera
series and Internet Video Server only.
4.2. Safety Recommendations
The safety guidelines are as follows:
λ Keep the board area clear and dust-free before, during, and after installation.
λ Keep tools away from walk areas where you and others could fall over them.
λ Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains, that could get
caught in the board.
λ Wear safety glasses if you are working under any conditions that might be hazardous to your
eyes.
λ Do not perform any action that creates a potential hazard to people or makes
the equipment unsafe.
λ Never attempt to lift an object that is too heavy for one person to handle.
4.3. Maintaining Safety with Electricity
Warning: Before working on a board or working near power supplies, unplug the power cord on AC units;
on DC units, disconnect the power at the circuit breaker.
Follow these guidelines when working on equipment powered by electricity:
λ Do not work alone if potentially hazardous conditions exist anywhere in your
work space.
λ Never assume that power is disconnected from a circuit; always check the
circuit.
extension cables, frayed power cords, and missing safety grounds.
λ If an electrical accident occurs, proceed as follows:
– Use caution; do not become a victim yourself.
– Disconnect power from the system.
– If possible, send another person to get medical aid. Otherwise, assess the condition of the victim
and then call for help.
– Determine if the person needs rescue breathing or external cardiac compressions; then take
appropriate action.
-7-
4.4. Installing a XG-630
λ Remove the XG-630 module from its protective packaging.
λ Avoiding Electrostatic Discharge
Before you install the XG-630 module, ground yourself by touching a piece of metal
to avoid electrostatic discharge (ESD). You should also take the following
precautions to prevent damage to the XG-630 module:
λ Keep the XG-630 module in its antistatic-shielded bag until
you are ready to install it.
λ Handle the XG-630 module by its edges.
λ Ensure the connector is connected to above Model’s board tightly.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2006:08:22 16:56:46+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2006:09:25 10:30:16+08:00
Metadata Date                   : 2006:09:25 10:30:16+08:00
Format                          : application/pdf
Creator                         : queenlin
Title                           : Microsoft Word - C_XG-630_User Maunal_060210.doc
Document ID                     : uuid:58431380-d472-4e83-b5ef-263505c4b355
Instance ID                     : uuid:7f5bd132-31aa-4343-8c19-4f724c53db39
Page Count                      : 6
Author                          : queenlin

EXIF Metadata provided by EXIF.tools