Z Wave B004Ekopoe Kwikset Smartcode 910 Installation Guide User Manual Smart Code
B004Uhja5U Kwikset Smartcode 910 Installation Guide B004UHJA5U_Kwikset_SmartCode_910_Installation_Guide B004UHJA5U_Kwikset_SmartCode_910_Installation_Guide 182 docs
2017-03-24
User Manual: Z-Wave B004Ekopoe Kwikset Smartcode 910 Installation Guide B004EKOPOE_Kwikset_SmartCode_910_Installation_Guide 176 docs
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
61019 / 02 1 Parts in the Box ENGLISH Latch and Strike Exterior Assembly B L D E 2-3/8" (60 mm) or 2-3/4" (70 mm) K 1-3/8" — 1-3/4"* 35 mm — 44 mm* 2-1/8" 1-1/2" or 54 mm 38 mm N F 1" 25 mm A2 Use and programming instructions are located on the reverse side of this document. Additional Tools (depending on application) G If needed, please contact Kwikset to order a drive-in latch for your lock. Kwikset 1-866-863-6584 www.kwikset.com 3 A 4 Adjust the backset of latch (if needed) Hold the latch in front of the door hole, with the latch face flush against the door edge. B Additional door preparation may be required for doors with 1-1/2" (38 mm) holes. Consult the drilling instructions at www.kwikset.com/doorprep. Q P H J R S 5 For doors with chiseled edge *Service kits for 2-1/4" (57 mm) thick doors are available through Kwikset. Select models only: Install latch If the latch holes are centered in the door hole, no adjustment is required. Proceed to step 4. If the latch holes are NOT centered, adjust latch. See “Latch Adjustment.” A / A2 M Installation Guide Required Tools Extend latch bolt Interior Assembly C A 2 Check dimensions 6 Prepare exterior keypad A For doors with 2-1/8" (54 mm) holes For doors without chiseled edge Install keypad and mounting plate B Route cable through center hole, then push cable into side hole. 2-1/8" A 54 mm A2 K Cable goes underneath latch G center hole side hole A / A2 E B C F A Latch Adjustment (only if needed) H G C (2x) 1-1/2" C 180° D Keep parallel to edge of door For doors with 1-1/2" (38 mm) holes wood block Tighten screws evenly 38 mm D Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (Q). Remove key when finished and make sure the latch bolt is fully extended. Q Q (2x) 7 8 Disassemble interior assembly and load battery pack A B C L Perform door handing process B This step will teach your lock the orientation of your door and is crucial to lock operation. ZigBee locks: Perform the Inclusion process after installation is complete. See “Z-Wave and ZigBee Systems” on the reverse side of this document. A B Make sure turnpiece is in the vertical position. N AA 10 Install interior assembly A “Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller. M D 9 Z-Wave locks only: Perform the Inclusion process Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller, and initiate the Inclusion process at the controller. Refer to your Z-Wave control system instructions for more information. Press button “A” on the lock one time to include it in your system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process. L Button “A” x4 C Lay cable flat against the interior housing. K N Ensure tight cable connection. Did the latch bolt retract and extend on its own when the battery pack was installed? D Z-Wave Controller HOLD L latch bolt A B D (2x) Programming instructions are located on the reverse side of this document. M Install the battery cover and re-key the lock B Select models only: NO Door handing process was successful! Proceed to Step 11 after latch bolt stops moving. Remove battery pack, wait 15 seconds, then attempt the process again. C If your door requires drilling, cut out the template and place it on the exterior side of the door. Complete door drilling instructions are available on the SmartCode deadbolt page of www.kwikset.com. S ball tip YES Template Edge R (3x) Keep “S” in a safe place, as you will need it to access the back panel for additional programming. Face J If needed, re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information. 1-3/8" (35 mm) 13 Program the lock Fold Centerline 1-3/4" (44 mm) 12 Install strike P (2x) If Inclusion is unsuccessful, initiate the Exclusion process at the controller, then press button “A” on the lock one time. Once the lock is fully excluded from the system, repeat the Inclusion process. 2-1/4" (57 mm) Do not install battery pack yet! Ensure correct polarity. For best results, use new non-rechargeable Alkaline batteries only. 11 B L Hold button until the latch bolt starts moving on its own. L C 12" 305 mm A Press and hold the Lock button while installing battery pack (L). 2-3/8" (60 mm) 2-3/4" (70 mm) Backset 61019 / 02 A B SmartCode at a Glance ENGLISH Exterior Note: Although the arched 910 model is illustrated, instructions are the same for all 910 models. C Normal Operation Unlocking the Door Interior (cover removed) Lock Inclusion Tip: You can press the Lock button before entering your user code to light up the keypad at night. User Guide Kwikset Keypad Lock button 1-866-863-6584 www.kwikset.com ZigBee: Initiate the Inclusion process at your ZigBee controller. Refer to your control system instructions for more information. Locking the Door Press Lock button once. Program button Switches Unsuccessful ZigBee Inclusion: Press button “B” nine times. Repeat the inclusion process. If no user codes are programmed, the Lock button will be disabled. Status LED Troubleshooting and FAQs are available online at www.kwikset.com. SmartKey tool hole Installation instructions are located on the reverse side of this document. Keyway Inclusion Exclusion Z-Wave Press button “A” once. Press button “A” once. ZigBee Press button “A” four times. Press button “B” nine times. System Notes Lock Exclusion “Exclusion” refers to the process in which the lock is removed from a Z-Wave or ZigBee controller. Initiate the Exclusion process at your Z-Wave or ZigBee controller. Refer to your control system instructions for more information. Incorrect Codes Turnpiece System Z-Wave: Perform the Inclusion process during lock installation. See step 8 in the Installation Guide. Button “A” Button “B” Use the chart to determine which button to press during Inclusion and Exclusion. “Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller. Enter user code. Back panel Switches, Z-Wave & Status ZigBeeLED Systems Colors and Keypad Warnings Codes Entered Lock Behavior Next Step One incorrect code entered. Keypad flashes red three times with three beeps* Re-enter code. Three incorrect codes entered within one minute. Keypad flashes red 15 times with 15 beeps* Re-enter code after 60 second keypad lockout. Z-Wave ZigBee In order to fully utilize this product, you must have a Z-Wave controller compatible with door locks. Z-Wave is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35 feet+ being typical installed distance from network controller. It may be necessary to install additional Z-Wave beaming capable devices that can serve as repeaters to enhance the communication path between the lock and controller for a more robust Z-Wave network. ZigBee is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the network controller. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller for a more robust ZigBee network. *If switch #3 is ON D a Programming Codes b Programming Information c Enabling and Adding a Mastercode (Optional for Enhanced Security) User codes can be programmed with or without a mastercode. Using a mastercode is an optional, added-security measure. It is not enabled by default. A mastercode is used to add and delete user codes, but it cannot unlock the door (unless the same code is programmed as a user code, though this is not recommended). The mastercode must be 4-8 digits. It is recommended that you add and delete all user codes through your Z-Wave or ZigBee control system. If your system does not allow this, the sections below will provide instructions for how to add and delete codes at the lock. Mastercode NOT enabled: 1 Press the Program button User Codes Requirements 1 Press and HOLD 2 Enter new mastercode. Program button until keypad flashes green (about 5 seconds). Each user code must be a unique code between 4 and 8 digits, depending on your control system. A total of 30 user codes may be programmed. the number of times that corresponds to the user code position being programmed. 3 Press Lock button once. Example: If programming the third code, press the button three times. How the Keypad Works Each button represents two numbers (i.e. 1 and 2 for the first button). You only need to push the button once to get either 1 or 2. For example: If your code is 1-2-5-6-8, 1 2 5 6 2 Enter new USER code. 8 4 Re-enter mastercode. 5 Press Lock button once. IF UNSUCCESSFUL Make sure the mastercode has not been programmed already. Attempt this procedure again, making sure to enter the same new mastercode in steps 2 and 4. Programming Behavior Successful Programming The keypad will flash green once, and you will hear one beep*. Deleting User Codes In order to delete a user code, you must override the code by adding a different user code in the same position. For example, if you want to delete the third code, add a different user code in position three. Mastercode enabled: 1 Press Program button once. Test the old user code to make sure it is inactive. The keypad will flash green and you will hear three beeps. If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock. See section “H.” 2 Enter MASTERCODE (the code that was enabled in section b) e Disabling and Deleting the Mastercode 3 Press Lock button once. 1 Press and HOLD TEST Make sure switch #3 is on, and then press the Program button once. If you hear three beeps and see the keypad flash green three times, the mastercode is enabled. the number of times that corresponds to the user code position being programmed. 3 Press Lock button once. Example: If programming the third code, press the button three times. 4 Press Lock button once. 5 Enter new USER code. 5 Re-enter mastercode. 6 Press Lock button once. red (x3) (x1) If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure. 6 Press Lock button once. (x3) IF UNSUCCESSFUL red (x6) Mastercode NOT enabled (x2) Note: The lock will time out after five seconds Make sure to enter a valid mastercode in step 2. TEST CODE Switch #3 OFF (x6) Make sure switch #3 is on, and then press the Program button once. If you don’t immediately hear three beeps or see the keypad flash green three times, the mastercode is disabled. If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Timeout Behavior Mastercode enabled TEST Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Timeout If no button is pressed for five seconds, the system will time out and you will need to restart the procedure. Switch #3 ON IF UNSUCCESSFUL Make sure the mastercode has been enabled before trying to disable it. Attempt this procedure again, making sure to enter the same mastercode in steps 3 and 5. IF UNSUCCESSFUL green (x1) 3 Enter mastercode. 4 Press the Program button Note: The lock will time out after five seconds. Unsuccessful Programming 2 Press Lock button once. Program button until keypad flashes green (about 5 seconds). Unsuccessful Programming The keypad will flash red three times, and you will hear three beeps*. Successful Programming d Adding User Codes While the door is open, test the user code to make sure it unlocks the door. red (x6) red (x3) TEST CODE While the door is open, test the user code to make sure it unlocks the door. If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure. *If switch #3 is ON E Regulatory Compliance This product complies with standards established by the following regulatory bodies: • • Federal Communications Commission (FCC) Industry Canada FCC F equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation. • • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. Troubleshooting Switches 1 Switch 1 2 3 OFF Function Door lock status LED blinks every 6 seconds Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed. 3 Audio Not used I Factory Reset 1 Remove Keypad Status LED battery pack. 4 2 4 H A factory reset will delete all codes associated with the lock. ON Industry Canada This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: ( 1 ) this device may not cause interference, and ( 2 ) this device must accept any interference, including interference that may cause undesired operation of the device. G Switches, Status LED Colors and Keypad Warnings Color Blinking green Lock Status Warning Unlocked Blinking amber Locked Blinking Red Low battery Solid Red Door Handing Process did not work properly. See online Troubleshooting guide. Keypad flashes red with fast beeping sound* for 3 – 4 seconds. *If switch #3 is ON Reason Solution Low battery Replace batteries Door jammed while attempting to lock Relock door. If needed, reposition strike. No user code programmed Program at least one user code 2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. status LED Problem: The latch bolt is not moving in the correct direction and the turnpiece will not rotate. Reason: The door handing process was not executed during installation, and the lock does not know the orientation of the door. Solution: Perform the door handing process, step 10 in the installation guide. For more troubleshooting, download the online Troubleshooting Guide, available at www.kwikset.com. 3 Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset. 4 Perform the door handing process again. See step 10 in the Installation Guide, on the reverse side of this document. 5 Perform the inclusion process again to add the lock back into your network and controller. Important Safeguards 1. Read all instructions in their entirety. 2. Familiarize yourself with all warning and caution statements. 3. Remind all family members of safety precautions. 4. Restrict access to your lock’s back panel and routinely check your settings to ensure they have not been altered without your knowledge. 5. Protect your user codes and mastercode. 6. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional. ©2014 Kwikset Corporation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.2-c003 61.141987, 2011/02/22-12:03:51 Create Date : 2014:06:19 13:03:42-07:00 Metadata Date : 2014:06:19 13:04:08-07:00 Modify Date : 2014:06:19 13:04:08-07:00 Creator Tool : Adobe InDesign CS5.5 (7.5) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 13967 bytes, use -b option to extract), (Binary data 12666 bytes, use -b option to extract) Instance ID : uuid:f9b2cff5-f595-4c80-9c90-bcc8e90a78b9 Document ID : xmp.did:857AD469DAE5E3118879EA17BA6B5071 Original Document ID : xmp.did:E30AB4B5B7C1E31195C5ED5447666419 Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:E30AB4B5B7C1E31195C5ED5447666419, xmp.iid:E70AB4B5B7C1E31195C5ED5447666419, xmp.iid:E80AB4B5B7C1E31195C5ED5447666419, xmp.iid:A05D21B0BCC1E31195C5ED5447666419, xmp.iid:0FFFD2AAC3C1E31195C5ED5447666419, xmp.iid:EA3328F8C3C1E31195C5ED5447666419, xmp.iid:18953B40D2C1E311B1D18B72A385EAE2, xmp.iid:868124CBF4C1E311B1D18B72A385EAE2, xmp.iid:878124CBF4C1E311B1D18B72A385EAE2, xmp.iid:C2F1A5C4F5C1E311B1D18B72A385EAE2, xmp.iid:B06ABAD5F5C1E311B1D18B72A385EAE2, xmp.iid:B16ABAD5F5C1E311B1D18B72A385EAE2, xmp.iid:FC9F950DF6C1E311B1D18B72A385EAE2, xmp.iid:F360FE94F6C1E311B1D18B72A385EAE2, xmp.iid:4E856D09FBC1E311B1D18B72A385EAE2, xmp.iid:1F471791FEC1E311B1D18B72A385EAE2, xmp.iid:28FB2DB2E3C3E31185D6DB07404AEAD3, xmp.iid:694FB7B2E3C3E31185D6DB07404AEAD3, xmp.iid:6A4FB7B2E3C3E31185D6DB07404AEAD3, xmp.iid:D5254A0EE6C3E31185D6DB07404AEAD3, xmp.iid:E8749969E7C3E31185D6DB07404AEAD3, xmp.iid:E9749969E7C3E31185D6DB07404AEAD3, xmp.iid:81CA56AFE8C3E31185D6DB07404AEAD3, xmp.iid:66496F4DEAC3E31185D6DB07404AEAD3, xmp.iid:A7DDC95AEAC3E31185D6DB07404AEAD3, xmp.iid:A8DDC95AEAC3E31185D6DB07404AEAD3, xmp.iid:B4B417B4EBC3E31185D6DB07404AEAD3, xmp.iid:5C14D0B9EBC3E31185D6DB07404AEAD3, xmp.iid:5D14D0B9EBC3E31185D6DB07404AEAD3, xmp.iid:5E14D0B9EBC3E31185D6DB07404AEAD3, xmp.iid:76045798F0C3E31185D6DB07404AEAD3, xmp.iid:8ECF775DF1C3E31185D6DB07404AEAD3, xmp.iid:C154E9E5F2C3E31185D6DB07404AEAD3, xmp.iid:43738FEEF2C3E31185D6DB07404AEAD3, xmp.iid:A0FD823BF3C3E31185D6DB07404AEAD3, xmp.iid:4B3FA181FEC3E31185D6DB07404AEAD3, xmp.iid:5BB72DA6FEC3E31185D6DB07404AEAD3, xmp.iid:0FECCB5A00C4E31185D6DB07404AEAD3, xmp.iid:FD8591AD00C4E31185D6DB07404AEAD3, xmp.iid:691CEDC200C4E31185D6DB07404AEAD3, xmp.iid:8A17343212C4E31185D6DB07404AEAD3, xmp.iid:6AE3145C15C4E31185D6DB07404AEAD3, xmp.iid:0D84F9ED18C4E31185D6DB07404AEAD3, xmp.iid:80D2F51319C4E31185D6DB07404AEAD3, xmp.iid:CACD8FC119C4E31185D6DB07404AEAD3, xmp.iid:7DB4D3B01AC4E31185D6DB07404AEAD3, xmp.iid:A2B3BA161EC4E31185D6DB07404AEAD3, xmp.iid:34BEE088ABC4E3119403B2F41AB2B203, xmp.iid:AB290DB4ABC4E3119403B2F41AB2B203, xmp.iid:AC290DB4ABC4E3119403B2F41AB2B203, xmp.iid:1D12B9B5C1C4E3119403B2F41AB2B203, xmp.iid:A6B91C34CCC4E3119403B2F41AB2B203, xmp.iid:8F85908DD9C4E3119403B2F41AB2B203, xmp.iid:0321FB9CE3C4E3119403B2F41AB2B203, xmp.iid:297E0AECE5C4E3119403B2F41AB2B203, xmp.iid:984E7F03E7C4E3119403B2F41AB2B203, xmp.iid:12C2D726E7C4E3119403B2F41AB2B203, xmp.iid:2F6A167DE8C4E3119403B2F41AB2B203, xmp.iid:EB266DDCE8C4E3119403B2F41AB2B203, xmp.iid:53A34D227CC5E311B2EFF83EBE3F5BB4, xmp.iid:891E60A27CC5E311B2EFF83EBE3F5BB4, xmp.iid:6DFA07957DC5E311B2EFF83EBE3F5BB4, xmp.iid:102740D47DC5E311B2EFF83EBE3F5BB4, xmp.iid:03E530DD7DC5E311B2EFF83EBE3F5BB4, xmp.iid:909E48EB7EC5E311B2EFF83EBE3F5BB4, xmp.iid:B59C6E2584C5E311B2EFF83EBE3F5BB4, xmp.iid:901B3C4084C5E311B2EFF83EBE3F5BB4, xmp.iid:33497FFF84C5E311B2EFF83EBE3F5BB4, xmp.iid:7386A17E96C5E311B2EFF83EBE3F5BB4, xmp.iid:95AFC71BB2C5E311B2EFF83EBE3F5BB4, xmp.iid:658F58C439C6E31181E3B11DCA995B9F, xmp.iid:718E555F3BC6E31181E3B11DCA995B9F, xmp.iid:D8397B6F3BC6E31181E3B11DCA995B9F, xmp.iid:38F86D8B54C6E311B4BAA2F2C494799F, xmp.iid:DD3F0AC655C6E311B4BAA2F2C494799F, xmp.iid:6AD8623198C9E311BA019F54F15970A5, xmp.iid:69BD781B28CAE31181CFFDF8C92D6326, xmp.iid:2516617F3ACAE31181CFFDF8C92D6326, xmp.iid:9EDE4180E3D3E311BED7EE8EA759DE57, xmp.iid:F4E44581E3D3E311BED7EE8EA759DE57, xmp.iid:38CB1EC0E8D3E311BED7EE8EA759DE57, xmp.iid:B5D530F2EBD3E311BED7EE8EA759DE57, xmp.iid:643F6A80F2D3E311BED7EE8EA759DE57, xmp.iid:00631BD2F2D3E311BED7EE8EA759DE57, xmp.iid:C184B66B43D5E311AC04D48B814078D3, xmp.iid:DD80167843D5E311AC04D48B814078D3, xmp.iid:76E3681112D6E3118E3AEBFB09EA2718, xmp.iid:BBCBFA3A12D6E3118E3AEBFB09EA2718, xmp.iid:B97806BFBFD6E311B9EAA20DABB633A1, xmp.iid:0338A06674DFE3119454952CD818B72D, xmp.iid:93CB627674DFE3119454952CD818B72D, xmp.iid:F89B608D75DFE3119454952CD818B72D, xmp.iid:DC5DB3B878DFE311A9B5E71517C62F31, xmp.iid:5E85044287DFE311A157DF9E82AAE2A1, xmp.iid:16A7748796DFE311A157DF9E82AAE2A1, xmp.iid:5A73C46B5EE0E311BE67B78019BF83CB, xmp.iid:9C285B13A9E5E3118879EA17BA6B5071, xmp.iid:BA1E0727A9E5E3118879EA17BA6B5071, xmp.iid:2785F15ADAE5E3118879EA17BA6B5071, xmp.iid:857AD469DAE5E3118879EA17BA6B5071, xmp.iid:6C987AED4AF2E31192F5BF50D74FD63B, xmp.iid:A85AB20B4BF2E31192F5BF50D74FD63B, xmp.iid:5A6760484CF2E31192F5BF50D74FD63B, xmp.iid:B9EEC3854DF2E31192F5BF50D74FD63B, xmp.iid:2719755A61F5E31185DAE97480D0FE5C, xmp.iid:3C3FBF0F9DF5E31185DAE97480D0FE5C, xmp.iid:BA7EF5249DF5E31185DAE97480D0FE5C, xmp.iid:5C32FC669EF5E31185DAE97480D0FE5C, xmp.iid:63AFC9C628F6E311ABA999F32053E387, xmp.iid:44A5BE1C2BF7E3119018D989EE91D309, xmp.iid:C19CF69CBBF7E311AE558D6EF27062D9, xmp.iid:3582022FBDF7E311AE558D6EF27062D9, xmp.iid:210FB62EE2F7E311BE7C87FDBDE90CDB, xmp.iid:220FB62EE2F7E311BE7C87FDBDE90CDB, xmp.iid:899E3295E9F7E311BE7C87FDBDE90CDB, xmp.iid:FBB3E2A0E9F7E311BE7C87FDBDE90CDB History When : 2014:04:11 13:38:04-07:00, 2014:04:11 14:02:33-07:00, 2014:04:11 14:02:33-07:00, 2014:04:11 14:03:10-07:00, 2014:04:11 14:53:08-07:00, 2014:04:11 14:55:17-07:00, 2014:04:11 16:37:31-07:00, 2014:04:11 20:44:47-07:00, 2014:04:11 20:47:37-07:00, 2014:04:11 20:51:46-07:00, 2014:04:11 20:52:14-07:00, 2014:04:11 20:53:27-07:00, 2014:04:11 20:53:48-07:00, 2014:04:11 20:57:35-07:00, 2014:04:11 21:29:29-07:00, 2014:04:11 21:54:45-07:00, 2014:04:14 07:47:26-07:00, 2014:04:14 07:47:27-07:00, 2014:04:14 07:56:09-07:00, 2014:04:14 08:04:20-07:00, 2014:04:14 08:14:02-07:00, 2014:04:14 08:22:50-07:00, 2014:04:14 08:23:09-07:00, 2014:04:14 08:34:44-07:00, 2014:04:14 08:35:06-07:00, 2014:04:14 08:35:18-07:00, 2014:04:14 08:44:45-07:00, 2014:04:14 08:44:55-07:00, 2014:04:14 08:45:22-07:00, 2014:04:14 08:45:56-07:00, 2014:04:14 09:19:46-07:00, 2014:04:14 09:25:17-07:00, 2014:04:14 09:36:15-07:00, 2014:04:14 09:36:30-07:00, 2014:04:14 09:38:39-07:00, 2014:04:14 10:59:21-07:00, 2014:04:14 11:00:22-07:00, 2014:04:14 11:12:35-07:00, 2014:04:14 11:14:54-07:00, 2014:04:14 11:15:30-07:00, 2014:04:14 13:20:18-07:00, 2014:04:14 13:42:56-07:00, 2014:04:14 14:08:30-07:00, 2014:04:14 14:09:33-07:00, 2014:04:14 14:14:25-07:00, 2014:04:14 14:21:06-07:00, 2014:04:14 14:45:26-07:00, 2014:04:15 07:37:56-07:00, 2014:04:15 07:39:09-07:00, 2014:04:15 07:39:57-07:00, 2014:04:15 11:31:47-07:00, 2014:04:15 11:31:47-07:00, 2014:04:15 13:07:21-07:00, 2014:04:15 14:19:22-07:00, 2014:04:15 14:35:53-07:00, 2014:04:15 14:43:42-07:00, 2014:04:15 14:44:41-07:00, 2014:04:15 14:54:16-07:00, 2014:04:15 14:56:56-07:00, 2014:04:16 08:31:09-07:00, 2014:04:16 08:34:44-07:00, 2014:04:16 08:41:31-07:00, 2014:04:16 08:43:17-07:00, 2014:04:16 08:43:32-07:00, 2014:04:16 08:51:05-07:00, 2014:04:16 09:28:30-07:00, 2014:04:16 09:29:15-07:00, 2014:04:16 09:34:36-07:00, 2014:04:16 11:39:51-07:00, 2014:04:16 14:57:58-07:00, 2014:04:17 07:08:36-07:00, 2014:04:17 07:20:05-07:00, 2014:04:17 07:20:32-07:00, 2014:04:17 10:20:17-07:00, 2014:04:17 10:29:04-07:00, 2014:04:21 14:02:05-07:00, 2014:04:22 07:12:16-07:00, 2014:04:22 09:23:54-07:00, 2014:05:04 16:26:21-07:00, 2014:05:04 16:26:23-07:00, 2014:05:04 17:03:56-07:00, 2014:05:04 17:26:48-07:00, 2014:05:04 18:13:44-07:00, 2014:05:04 18:16:01-07:00, 2014:05:06 10:25:29-07:00, 2014:05:06 10:25:50-07:00, 2014:05:07 11:04:44-07:00, 2014:05:07 11:05:53-07:00, 2014:05:08 07:47:58-07:00, 2014:05:19 09:41:18-07:00, 2014:05:19 09:41:44-07:00, 2014:05:19 09:49:32-07:00, 2014:05:19 10:12:13-07:00, 2014:05:19 11:56:17-07:00, 2014:05:19 13:45:36-07:00, 2014:05:20 13:36:29-07:00, 2014:05:27 07:13:28-07:00, 2014:05:27 07:14:01-07:00, 2014:05:27 13:06:38-07:00, 2014:05:27 13:06:39-07:00, 2014:06:12 09:02:17-07:00, 2014:06:12 09:03:08-07:00, 2014:06:12 09:11:59-07:00, 2014:06:12 09:20:52-07:00, 2014:06:16 07:20:23-07:00, 2014:06:16 14:27:47-07:00, 2014:06:16 14:28:23-07:00, 2014:06:16 14:37:23-07:00, 2014:06:17 07:07:54-07:00, 2014:06:18 13:57:08-07:00, 2014:06:19 07:11:31-07:00, 2014:06:19 07:22:46-07:00, 2014:06:19 11:47:37-07:00, 2014:06:19 11:47:56-07:00, 2014:06:19 12:40:35-07:00, 2014:06:19 12:40:54-07:00 History Software Agent : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Derived From Instance ID : xmp.iid:2785F15ADAE5E3118879EA17BA6B5071 Derived From Document ID : xmp.did:F4E44581E3D3E311BED7EE8EA759DE57 Derived From Original Document ID: xmp.did:E30AB4B5B7C1E31195C5ED5447666419 Derived From Rendition Class : default Doc Change Count : 5801 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 2 Creator : Adobe InDesign CS5.5 (7.5)EXIF Metadata provided by EXIF.tools