ZEGO ELECTRONIC 16RX Copter of Dominator User Manual
ZEGO ELECTRONIC COMPANY LIMITED Copter of Dominator Users Manual
Users Manual
6001432 User’s Guide Age 12+ Dominator 2.0 Blade guard Drone 6001432_PM_En.indd 1 6/21/2016 12:04:20 PM Contents Features............................................................................................. 3 Package Contents............................................................................. 3 Specifications.................................................................................... 3 Fly Safely............................................................................................ 3 Charge the Drone.............................................................................. 4 Lithium Battery Notes...............................................................................................4 Install Batteries in the Remote Control........................................... 4 Battery Notes...............................................................................................................5 About Expert/ Easy Modes (Ex/Ez)................................................. 5 Pairing................................................................................................. 5 Remote Control Overview............................................................... 6 Fly Your Drone................................................................................... 8 Trim Your Drone...........................................................................................................8 Land Your Drone..........................................................................................................8 Perform Stunts............................................................................................................8 Replace Damaged Propellers........................................................... 9 Troubleshooting................................................................................ 9 Drone does not respond...........................................................................................9 Drone difficult to control...........................................................................................9 Drone swerves or moves erratically before taking off.................................. 10 FCC Information.............................................................................. 10 Limited Warranty............................................................................. 10 CHOKING HAZARD! Small parts. Not for children under 3 years. 6001432_PM_En.indd 2 6/21/2016 12:04:20 PM We hope you enjoy your Dominator 2.0 Blade Guard Drone from RadioShack. Congratulations! No FAA Registration is required for this drone. Please read this user’s guide before setting up and using your drone. Features •• •• •• •• 6-axis super stabilizing control system 360° flip stunt mode Easy (Ez) and Expert (Ex) play modes Detachable blade guards to create two looks Package Contents Blade guards detached •• Drone with detachable propeller guards •• Remote Control • USB Charging Cable •• Spare Propellers with screw (4) • User’s Guide Specifications Power......................................................................................................................................... Drone..........................................built-in 3.7V, 390mAh lithium polymer battery Remote Control............................................................................. 4 × AAA batteries Control Distance.......................................................................................... 100 ft. (30m) Specifications are subject to change and improvement without notice. Actual product may vary from the images found in this document. Fly Safely • Do not fly the drone near or at other people or animals. • Do not fly your drone where emergency responders are working, or emergency aircraft are operating. • When flying outdoors, keep the drone away from power lines, trees, weeds, and water. • Do not fly your drone over private property where you are not welcomed. • When flying indoors, keep the drone away from walls, air conditioning, air vents, fans, breakable objects, and other obstacles. • Keep eyes, hands, hair, and loose clothing away from moving propellers. •• Adult supervision is recommended at all times. 6001432_PM_En.indd 3 Complies with the European Union’s “Restriction of Hazardous Substances Directive,” which protects the environment by restricting specific hazardous materials and products. 6/21/2016 12:04:21 PM Charge the Drone 1. Make sure the drone is turned off. 2. Connect the included USB charging cable to the drone's CHG jack and a USB power source. The USB connector LED lights red during charging, and turns off when charging is complete. CHG LED ON/ OFF A full charge takes about 55-60 minutes, and provides up to 5 minutes of flight time. 3. After charging, unplug the charging cable. Caution •• Use only the included USB charging cable to charge the drone's battery. Other cables may damage the drone. •• Always let the drone battery cool before recharging. Lithium Battery Notes Your drone uses a built-in lithium polymer battery for power. Follow the instructions for charging. •• Do not charge longer than recommended. Unplug the charging cable when the drone is charged. •• Do not puncture or crush. Do not disassemble. •• Do not dispose of lithium batteries in the trash. •• If the electrolyte in the cells should get on your skin, thoroughly wash with soap and water. If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention. •• Do not attempt to charge or operate damaged toys. Install Batteries in the Remote Control 1. Make sure the remote control is turned off. 2. Use a screwdriver to open the twin battery compartments. Then insert four AAA batteries (not included), matching the polarities (+ and –) marked inside. Replace the cover. 6001432_PM_En.indd 4 6/21/2016 12:04:21 PM Note: If the remote control’s LED flashes during use, the batteries are low and should be replaced. Battery Notes •• Dispose of old batteries promptly and properly. Do not burn or bury them. Use only fresh batteries of the required size and recommended type. •• Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. •• Remove batteries during longer storage periods. Batteries can leak chemicals that can damage electronic parts. About Expert/ Easy Fly Modes (Ex/Ez) This drone is designed with 2 play modes: Ex (Expert) for advanced pilots to fly at a higher speed and perform stunts. Ez (Easy) for beginners and new drone owners. This operates at a slower speed to help you focus on basic navigation and develop a feel of the throttle's sensitivity. By default, in Ez mode, the stunt and speed options are disabled to prevent them from being accidentally activated. •• When pairing and flying for the first time, we recommend you use Ez for test flights and honing your takeoff, steering and landing skills. Pairing 1. Turn on the drone. The drone's LEDs flash. 2. Place the drone on level ground. 3. Turn on the remote control to Ez or Ex . The remote control's LED flashes. 4. Move the throttle all the way up and then down to pair the remote control with the drone. The drone’s propellers remain still during pairing. When paired, the LEDs on both the remote control and drone light steadily. Note: If pairing fails, turn off the drone and remote control and repeat the steps above, or change locations to avoid electrical interference. 6001432_PM_En.indd 5 6/21/2016 12:04:22 PM Remote Control Overview Forward / Reverse Movement Trim LED Throttle Ascend Turn left 6001432_PM_En.indd 6 Push (Stunt mode) Turn right Descend 6/21/2016 12:04:22 PM 6001432_PM_En.indd 7 Left / Right Slide Trim Steering Forward Slide left Push (High/low Slide right speed) Backward Ex/ OFF/ Ez Expert/ Off/ Easy mode 6/21/2016 12:04:22 PM Fly Your Drone 1. After pairing, with the drone on the ground, move the throttle forward to ascend. To avoid ground air turbulence, fly the drone at least 1 ft. (30cm) off the ground. For advanced users: Hold the remote control with one hand, resting your thumb on the throttle. Throw the drone about 9 ft. (3m) away from you, and move the throttle forward to fly. The drone adjusts itself automatically and flies smoothly. 2. For speed options, pair and fly in Ex mode. Push the steering control in to switch between high speed (double beep) and low speed (single beep). IMPORTANT: If your drone crashes upside down, pull the throttle all the way down. Wait till the propellers have stopped still before you handle the drone. Trim Your Drone Move the throttle forward and see how the drone reacts. Reverse/ Forward Movement Trim: If the drone tends to move forward, press ; if it tends to move backward, press . Left/Right Slide Trim: If the drone tends to slide right, press ; if it tends to slide left, press . Note: The remote control beeps when you press a trim control, but stops beeping when you reach maximum trim adjustment. Land Your Drone 1. Slowly move the throttle backward to descend. Avoid moving the throttle too quickly, as it can stop the propellers instantly and cause the drone to crash. 2. When you finish playing, turn off the remote control and drone. Perform Stunts CAUTION: Make sure there is enough space for the drone to perform stunts without crashing into objects or people. 1. In Ex mode, push the throttle control to activate stunt mode. The remote control beeps repeatedly. 2. Use the steering control to perform stunts: •• Front flip: Move steering forward •• Back flip: Move steering backward •• Barrel roll: Move steering right or left 3. The drone automatically exits stunt mode after performing a stunt, or push in the throttle control again to exit immediately. 6001432_PM_En.indd 8 6/21/2016 12:04:22 PM Replace Damaged Propellers The left and right propellers of the drone are different, and marked A/B on the propeller. You must use the correct propeller in the correct location, otherwise the drone will fail to take off. To replace a damaged propeller, use a screwdriver to remove the old propeller. Insert a new matching propeller onto the propeller axle, then screw securely, but do not overtighten as the propeller then won't turn. WARNING: •• To avoid injury and damage, check the propellers for nicks and breaks and make sure they are securely attached before and after each flight. Replace any damaged propellers. •• Use only the supplied propellers. Do not alter, modify, or customize the propellers. Troubleshooting Drone does not respond •• Make sure the drone and remote control are switched on and paired. •• Drone battery maybe low. Fully charge the battery. See “Charge the Drone.“ •• Remote control batteries maybe low. Replace the batteries. •• Make sure the drone is within the control range (100 ft./30 m) and in line of sight. Drone difficult to control •• The throttle control is very sensitive. Use small, fine movements to control. •• Practice in Ez (Easy) mode. •• Propellers maybe deformed or damaged. Adjust propellers by hand. If you cannot adjust them, replace with the spare propellers. 6001432_PM_En.indd 9 6/21/2016 12:04:23 PM Drone swerves or moves erratically before taking off •• The gyroscope inside your drone needs calibrating: Do the following: 1. With your drone and remote control switched on and paired, place the drone on level ground. 2. Move the throttle all the way down. 3. Move the steering forward and hold this position for a few seconds until the drone LEDs start to blink. 4. Release the steering. The drone LEDs light steadily, indicating successful calibration. You are now ready for takeoff. •• See “Trim Your Drone" to fine tune hovering and movement to further improve control of your drone after calibration. FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • onnect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. If you cannot eliminate the interference, the FCC requires that you stop using your equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Limited Warranty Go to www.radioshack.com/help for details. RadioShack Customer Relations 300 RadioShack Circle, Fort Worth, TX 76102 www.radioshack.com © 2016 General Wireless Operations Inc. All rights reserved. RadioShack is a registered trademark used by General Wireless Operations Inc. dba RadioShack 6001432_PM_En.indd 10 Printed in China 06A16 6001432 10 6/21/2016 12:04:23 PM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:12:18 Create Date : 2016:06:21 12:04:19+08:00 Metadata Date : 2016:06:21 12:04:23+08:00 Modify Date : 2016:06:21 12:04:23+08:00 Creator Tool : Adobe InDesign CS4 (6.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9851 bytes, use -b option to extract) Instance ID : uuid:92f3f4d0-a49b-4904-a369-7b9e17a39f36 Document ID : xmp.did:AC4C797A0329E511895EA42A20E81BFE Original Document ID : xmp.did:AC4C797A0329E511895EA42A20E81BFE Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:AC4C797A0329E511895EA42A20E81BFE, xmp.iid:AD4C797A0329E511895EA42A20E81BFE, xmp.iid:AE4C797A0329E511895EA42A20E81BFE, xmp.iid:AF4C797A0329E511895EA42A20E81BFE, xmp.iid:EBE9E68C3229E511B65BAF2671903B2A, xmp.iid:0B5DB2D5DF29E511ADF9FA8FB5FEC066, xmp.iid:0C5DB2D5DF29E511ADF9FA8FB5FEC066, xmp.iid:DB239B13622BE5118242D9AB48BF1E5D, xmp.iid:746BF150722BE5118242D9AB48BF1E5D, xmp.iid:7FC294EC492CE51192859544A231B23D, xmp.iid:81C294EC492CE51192859544A231B23D, xmp.iid:82C294EC492CE51192859544A231B23D, xmp.iid:83C294EC492CE51192859544A231B23D, xmp.iid:40A6E299702CE511A017DF602D7CBD09, xmp.iid:4D584102AB2EE51180C2EB3845C0A494, xmp.iid:4F584102AB2EE51180C2EB3845C0A494, xmp.iid:356D12201E30E511A426CBD70BCA519F, xmp.iid:DDD75736E530E5118F2BB9FA721EDF5B, xmp.iid:E0D75736E530E5118F2BB9FA721EDF5B, xmp.iid:74BD3A7D103CE5118B6B8615AA2EC394, xmp.iid:A3AE045ACA3CE511AB69E3D93D05B71D, xmp.iid:A5AE045ACA3CE511AB69E3D93D05B71D, xmp.iid:151071290C3FE511AC23CC9977624C9A, xmp.iid:171071290C3FE511AC23CC9977624C9A, xmp.iid:DFD76A593B3FE511AC23CC9977624C9A, xmp.iid:71BD782FD93FE511A25BC23D283EB671, xmp.iid:7E2C1889F93FE511A25BC23D283EB671, xmp.iid:BE31EE56A840E5118B34912914868200, xmp.iid:BF31EE56A840E5118B34912914868200, xmp.iid:C331EE56A840E5118B34912914868200, xmp.iid:19830D319141E5118CA68ABD9B14510E, xmp.iid:1E830D319141E5118CA68ABD9B14510E, xmp.iid:15B8503AA12BE611987BCBDCE322D010, xmp.iid:16B8503AA12BE611987BCBDCE322D010, xmp.iid:B607EAA9562CE61189C4C0B5D9746829, xmp.iid:B707EAA9562CE61189C4C0B5D9746829, xmp.iid:BB07EAA9562CE61189C4C0B5D9746829, xmp.iid:B9478530312DE61188A9C93685EBDC67, xmp.iid:F814BA4F6B33E61196ABE3F508F7EFC4, xmp.iid:F914BA4F6B33E61196ABE3F508F7EFC4, xmp.iid:A9460484AC33E61196ABE3F508F7EFC4, xmp.iid:F50B8BE95234E611AD4EB04D14F884E5, xmp.iid:F80B8BE95234E611AD4EB04D14F884E5, xmp.iid:F90B8BE95234E611AD4EB04D14F884E5, xmp.iid:FB0B8BE95234E611AD4EB04D14F884E5, xmp.iid:FC0B8BE95234E611AD4EB04D14F884E5, xmp.iid:4A0E1C345F37E611ACAFED6DB2A11F23 History When : 2015:07:13 12:02:01+08:00, 2015:07:13 12:07:28+08:00, 2015:07:13 12:07:28+08:00, 2015:07:13 12:12:43+08:00, 2015:07:13 15:41:28+08:00, 2015:07:14 12:21:44+08:00, 2015:07:14 12:25:13+08:00, 2015:07:16 11:40:50+08:00, 2015:07:16 16:41:57+08:00, 2015:07:17 14:06:11+08:00, 2015:07:17 14:40:56+08:00, 2015:07:17 14:41:32+08:00, 2015:07:17 14:42:02+08:00, 2015:07:17 18:43:03+08:00, 2015:07:20 16:00:14+08:00, 2015:07:20 17:42:11+08:00, 2015:07:22 18:03:49+08:00, 2015:07:23 14:09:43+08:00, 2015:07:23 16:44:51+08:00, 2015:08:06 16:51:20+08:00, 2015:08:07 16:31:03+08:00, 2015:08:07 17:03:51+08:00, 2015:08:10 16:01:26+08:00, 2015:08:10 16:12:04+08:00, 2015:08:10 19:02:48+08:00, 2015:08:11 15:04+08:00, 2015:08:11 16:56:09+08:00, 2015:08:12 12:16:45+08:00, 2015:08:12 12:17:51+08:00, 2015:08:12 12:25:59+08:00, 2015:08:13 17:12:20+08:00, 2015:08:13 17:51:44+08:00, 2016:06:06 19:22:15+08:00, 2016:06:06 19:25:31+08:00, 2016:06:07 10:22:21+08:00, 2016:06:07 10:51:42+08:00, 2016:06:07 14:27:39+08:00, 2016:06:08 12:53:34+08:00, 2016:06:16 17:35:20+08:00, 2016:06:16 17:40:04+08:00, 2016:06:16 19:14:45+08:00, 2016:06:17 14:15:39+08:00, 2016:06:17 15:40:55+08:00, 2016:06:17 15:46:16+08:00, 2016:06:17 17:02:25+08:00, 2016:06:17 17:19:51+08:00, 2016:06:21 11:28:48+08:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0 History Changed : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, / Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 240.00, 240.00, 300.00, 240.00, 240.00, 240.00, 72.00, 300.00, 300.00, 300.00, 240.00, 240.00, 300.00, 240.00, 240.00, 300.00, 72.00 Manifest Placed Y Resolution : 300.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 240.00, 240.00, 300.00, 240.00, 240.00, 240.00, 72.00, 300.00, 300.00, 300.00, 240.00, 240.00, 300.00, 240.00, 240.00, 300.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : xmp.iid:D97037E9D2FFE4119F89C098347FA4CC, xmp.iid:4A6A0DDAE27DE511AF06BA6A6BE2DAAC, xmp.iid:068BDB1F2D34E611BD6CD10DC53E15B9, xmp.iid:149E821184F1E3118267EBCE727CA1B8, xmp.iid:0480117407206811822AD28DAC455A03, xmp.iid:068BDB1F2D34E611BD6CD10DC53E15B9, xmp.iid:12EC64C0ADA5E2119884F4F49E79F0EF, xmp.iid:F21EDE7D52E2E41191C8F568AFAC1FC3, xmp.iid:946395F3F20FE511A25083AA911E4A56, xmp.iid:B7E382822C34E611BD6CD10DC53E15B9, xmp.iid:1836CDFB21206811822AACF055DA9159, xmp.iid:AFE382822C34E611BD6CD10DC53E15B9, xmp.iid:1836CDFB21206811822AACF055DA9159, xmp.iid:8E3D5C9B3A83E31196D6A30769117383, xmp.iid:96A3B86F5F34E611B6D7BB548EBFF580, xmp.iid:7C806E735734E611BD6CD10DC53E15B9, xmp.iid:7C806E735734E611BD6CD10DC53E15B9, xmp.iid:632822F6270FE51190F9F7D2A6D24887, xmp.iid:612822F6270FE51190F9F7D2A6D24887, xmp.iid:058BDB1F2D34E611BD6CD10DC53E15B9, xmp.iid:3643AC4F0310E511A25083AA911E4A56, xmp.iid:6363A6670110E511A25083AA911E4A56, xmp.iid:068BDB1F2D34E611BD6CD10DC53E15B9, uuid:a05e4252-5794-4caa-b008-83799a7e7f98 Manifest Reference Document ID : xmp.did:D97037E9D2FFE4119F89C098347FA4CC, xmp.did:4A6A0DDAE27DE511AF06BA6A6BE2DAAC, xmp.did:f0a21b48-33b7-441a-858e-7bda3a6f262b, xmp.did:149E821184F1E3118267EBCE727CA1B8, xmp.did:f5e2f668-70c7-4ebf-a1b0-92084816a7bf, xmp.did:f0a21b48-33b7-441a-858e-7bda3a6f262b, xmp.did:12EC64C0ADA5E2119884F4F49E79F0EF, xmp.did:3C68B56148E2E41191C8F568AFAC1FC3, xmp.did:D341939DE20FE511A25083AA911E4A56, xmp.did:CB157C2D3A206811822AACF055DA9159, xmp.did:955F6A18E60FE511A25083AA911E4A56, xmp.did:955F6A18E60FE511A25083AA911E4A56, xmp.did:955F6A18E60FE511A25083AA911E4A56, xmp.did:8E3D5C9B3A83E31196D6A30769117383, xmp.did:ce46b3a7-b932-4fea-a814-1dbf479b04ae, xmp.did:ce46b3a7-b932-4fea-a814-1dbf479b04ae, xmp.did:ce46b3a7-b932-4fea-a814-1dbf479b04ae, xmp.did:B76234639209E5119CC0A32A3D882BD6, xmp.did:B76234639209E5119CC0A32A3D882BD6, xmp.did:b294c78b-82f7-47a7-b952-03469d50f3e8, xmp.did:986395F3F20FE511A25083AA911E4A56, xmp.did:6063A6670110E511A25083AA911E4A56, xmp.did:f0a21b48-33b7-441a-858e-7bda3a6f262b, xmp.did:88C42DEB402AE411B642B824226E9C2F Doc Change Count : 2365 Format : application/pdf Producer : Adobe PDF Library 9.0 Trapped : False Page Count : 10 Creator : Adobe InDesign CS4 (6.0)EXIF Metadata provided by EXIF.tools